* (C) Copyright 2002
* Sysgo Real-Time Solutions, GmbH <www.elinos.com>
* Marius Groeger <mgroeger@sysgo.de>
- * Gary Jennejohn <gj@denx.de>
+ * Gary Jennejohn <garyj@denx.de>
* David Mueller <d.mueller@elsoft.ch>
*
* Modified for the friendly-arm SBC-2410X by
/*
* Size of malloc() pool
*/
-#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024)
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/*
* Hardware drivers
/*
* select serial console configuration
*/
+#define CONFIG_S3C24X0_SERIAL
#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on SBC2410X */
/************************************************************
#define CONFIG_BAUDRATE 115200
-/***********************************************************
- * Command definition
- ***********************************************************/
-#define CONFIG_COMMANDS \
- (CONFIG_CMD_DFL | \
- CFG_CMD_CACHE | \
- /*CFG_CMD_NAND |*/ \
- /*CFG_CMD_EEPROM |*/ \
- /*CFG_CMD_I2C |*/ \
- /*CFG_CMD_USB |*/ \
- CFG_CMD_REGINFO | \
- CFG_CMD_DATE | \
- CFG_CMD_PING | \
- CFG_CMD_DHCP | \
- CFG_CMD_ELF)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_PING
+
#define CONFIG_BOOTDELAY 3
-#define CONFIG_BOOTARGS "console=ttySAC0 root=/dev/nfs nfsroot=192.168.0.1:/friendly-arm/rootfs_netserv ip=192.168.0.69:192.168.0.1:192.168.0.1:255.255.255.0:debian:eth0:off"
+#define CONFIG_BOOTARGS "console=ttySAC0 root=/dev/nfs " \
+ "nfsroot=192.168.0.1:/friendly-arm/rootfs_netserv " \
+ "ip=192.168.0.69:192.168.0.1:192.168.0.1:255.255.255.0:debian:eth0:off"
#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_IPADDR 192.168.0.69
/*#define CONFIG_BOOTFILE "elinos-lart" */
#define CONFIG_BOOTCOMMAND "dhcp; bootm"
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
/* what's this ? it's not used anywhere */
#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "[ ~ljh@GDLC ]# " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x30000000 /* memtest works on */
-#define CFG_MEMTEST_END 0x33F00000 /* 63 MB in DRAM */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "[ ~ljh@GDLC ]# " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */
+#define CONFIG_SYS_MEMTEST_START 0x30000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x33F00000 /* 63 MB in DRAM */
-#define CFG_LOAD_ADDR 0x33000000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x33000000 /* default load address */
/* the PWM TImer 4 uses a counter of 15625 for 10 ms, so we need */
/* it to wrap 100 times (total 1562500) to get 1 sec. */
-#define CFG_HZ 1562500
+#define CONFIG_SYS_HZ 1562500
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*-----------------------------------------------------------------------
* Stack sizes
#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
-#define CFG_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
/*-----------------------------------------------------------------------
* FLASH and environment organization
#define CONFIG_AMD_LV800 1 /* uncomment this if you have a LV800 flash */
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#ifdef CONFIG_AMD_LV800
#define PHYS_FLASH_SIZE 0x00100000 /* 1MB */
-#define CFG_MAX_FLASH_SECT (19) /* max number of sectors on one chip */
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x0F0000) /* addr of environment */
+#define CONFIG_SYS_MAX_FLASH_SECT (19) /* max number of sectors on one chip */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x0F0000) /* addr of environment */
#endif
#ifdef CONFIG_AMD_LV400
#define PHYS_FLASH_SIZE 0x00080000 /* 512KB */
-#define CFG_MAX_FLASH_SECT (11) /* max number of sectors on one chip */
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x070000) /* addr of environment */
+#define CONFIG_SYS_MAX_FLASH_SECT (11) /* max number of sectors on one chip */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x070000) /* addr of environment */
#endif
/* timeout values are in ticks */
-#define CFG_FLASH_ERASE_TOUT (5*CFG_HZ) /* Timeout for Flash Erase */
-#define CFG_FLASH_WRITE_TOUT (5*CFG_HZ) /* Timeout for Flash Write */
+#define CONFIG_SYS_FLASH_ERASE_TOUT (5*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
+#define CONFIG_SYS_FLASH_WRITE_TOUT (5*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
/*-----------------------------------------------------------------------
* NAND flash settings
*/
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define NAND_WAIT_READY(nand) NF_WaitRB()
-#define NAND_DISABLE_CE(nand) NF_SetCE(NFCE_HIGH)
-#define NAND_ENABLE_CE(nand) NF_SetCE(NFCE_LOW)
-#define WRITE_NAND_COMMAND(d, adr) NF_Cmd(d)
-#define WRITE_NAND_COMMANDW(d, adr) NF_CmdW(d)
-#define WRITE_NAND_ADDRESS(d, adr) NF_Addr(d)
-#define WRITE_NAND(d, adr) NF_Write(d)
-#define READ_NAND(adr) NF_Read()
-/* the following functions are NOP's because S3C24X0 handles this in hardware */
-#define NAND_CTL_CLRALE(nandptr)
-#define NAND_CTL_SETALE(nandptr)
-#define NAND_CTL_CLRCLE(nandptr)
-#define NAND_CTL_SETCLE(nandptr)
-/* #undef CONFIG_MTD_NAND_VERIFY_WRITE */
-#endif /* CONFIG_COMMANDS & CFG_CMD_NAND */
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_NAND_S3C2410
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
+#endif /* CONFIG_CMD_NAND */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_CMDLINE_TAG
-#define CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_CMDLINE_EDITING
projects / karo-tx-uboot.git / blobdiff