arm: ti: Increase malloc size to 16MB for armv7 boards

[karo-tx-uboot.git] / include / configs / tam3517-common.h

diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h
index 48698b57da40acfab64e6705165906735cf920bb..0c2f0f19c827f133e99066304d32f60fccc431ec 100644 (file)
--- a/include/configs/tam3517-common.h
+++ b/include/configs/tam3517-common.h
@@ -117,14 +117,13 @@
 #undef CONFIG_CMD_IMLS
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED           400000
-#define CONFIG_SYS_I2C_SLAVE           1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED    400000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE    1
+#define CONFIG_SYS_I2C_OMAP34XX
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50            /* base address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1               /* bytes of address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW    0x07
-#define CONFIG_DRIVER_OMAP34XX_I2C
-
 
 /*
  * Board NAND Info.
@@ -186,8 +185,8 @@
 /* Configure the PISMO */
 #define PISMO1_NAND_SIZE               GPMC_SIZE_128M
 
+#define CONFIG_NAND
 #define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
 #define CONFIG_ENV_IS_IN_NAND
 #define SMNAND_ENV_OFFSET              0x180000 /* environment starts here */
 
@@ -225,6 +224,7 @@
 #define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SPL_CONSOLE
 #define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SPL_NAND_SOFTECC
 #define CONFIG_SPL_NAND_WORKSPACE      0x8f07f000 /* below BSS */
 
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
@@ -250,6 +250,7 @@
 #define CONFIG_SPL_BSS_MAX_SIZE                0x80000
 
 /* NAND boot config */
+#define CONFIG_SYS_NAND_BUSWIDTH_16BIT 16
 #define CONFIG_SYS_NAND_PAGE_COUNT     64
 #define CONFIG_SYS_NAND_PAGE_SIZE      2048
 #define CONFIG_SYS_NAND_OOBSIZE                64
@@ -369,7 +370,7 @@ struct tam3517_module_info {
 
 #define TAM3517_READ_EEPROM(info, ret) \
 do {                                                           \
-       i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);   \
+       i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \
        if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,          \
                (void *)info, sizeof(*info)))                   \
                ret = 1;                                        \