* enough as to be incompatible for compilation purposes.
*/
-#ifdef CONFIG_DM_I2C
-
enum dm_i2c_chip_flags {
DM_I2C_CHIP_10BIT = 1 << 0, /* Use 10-bit addressing */
DM_I2C_CHIP_RD_ADDRESS = 1 << 1, /* Send address for each read byte */
DM_I2C_CHIP_WR_ADDRESS = 1 << 2, /* Send address for each write byte */
};
+struct udevice;
/**
* struct dm_i2c_chip - information about an i2c chip
*
* An I2C chip is a device on the I2C bus. It sits at a particular address
* and normally supports 7-bit or 10-bit addressing.
*
- * To obtain this structure, use dev_get_parentdata(dev) where dev is the
- * chip to examine.
+ * To obtain this structure, use dev_get_parent_platdata(dev) where dev is
+ * the chip to examine.
*
* @chip_addr: Chip address on bus
* @offset_len: Length of offset in bytes. A single byte offset can
uint flags;
#ifdef CONFIG_SANDBOX
struct udevice *emul;
+ bool test_mode;
#endif
};
* bus can operate at different speeds (measured in Hz, typically 100KHz
* or 400KHz).
*
- * To obtain this structure, use bus->uclass_priv where bus is the I2C
- * bus udevice.
+ * To obtain this structure, use dev_get_uclass_priv(bus) where bus is the
+ * I2C bus udevice.
*
* @speed_hz: Bus speed in hertz (typically 100000)
*/
};
/**
- * i2c_read() - read bytes from an I2C chip
+ * dm_i2c_read() - read bytes from an I2C chip
*
* To obtain an I2C device (called a 'chip') given the I2C bus address you
* can use i2c_get_chip(). To obtain a bus by bus number use
*
* @return 0 on success, -ve on failure
*/
-int i2c_read(struct udevice *dev, uint offset, uint8_t *buffer,
- int len);
+int dm_i2c_read(struct udevice *dev, uint offset, uint8_t *buffer, int len);
/**
- * i2c_write() - write bytes to an I2C chip
+ * dm_i2c_write() - write bytes to an I2C chip
*
- * See notes for i2c_read() above.
+ * See notes for dm_i2c_read() above.
*
* @dev: Chip to write to
* @offset: Offset within chip to start writing
*
* @return 0 on success, -ve on failure
*/
-int i2c_write(struct udevice *dev, uint offset, const uint8_t *buffer,
- int len);
+int dm_i2c_write(struct udevice *dev, uint offset, const uint8_t *buffer,
+ int len);
/**
- * i2c_probe() - probe a particular chip address
+ * dm_i2c_probe() - probe a particular chip address
*
* This can be useful to check for the existence of a chip on the bus.
* It is typically implemented by writing the chip address to the bus
* @devp: Returns the device found, or NULL if none
* @return 0 if a chip was found at that address, -ve if not
*/
-int i2c_probe(struct udevice *bus, uint chip_addr, uint chip_flags,
- struct udevice **devp);
+int dm_i2c_probe(struct udevice *bus, uint chip_addr, uint chip_flags,
+ struct udevice **devp);
+
+/**
+ * dm_i2c_reg_read() - Read a value from an I2C register
+ *
+ * This reads a single value from the given address in an I2C chip
+ *
+ * @addr: Address to read from
+ * @return value read, or -ve on error
+ */
+int dm_i2c_reg_read(struct udevice *dev, uint offset);
+
+/**
+ * dm_i2c_reg_write() - Write a value to an I2C register
+ *
+ * This writes a single value to the given address in an I2C chip
+ *
+ * @addr: Address to write to
+ * @val: Value to write (normally a byte)
+ * @return 0 on success, -ve on error
+ */
+int dm_i2c_reg_write(struct udevice *dev, uint offset, unsigned int val);
/**
- * i2c_set_bus_speed() - set the speed of a bus
+ * dm_i2c_set_bus_speed() - set the speed of a bus
*
* @bus: Bus to adjust
* @speed: Requested speed in Hz
* @return 0 if OK, -EINVAL for invalid values
*/
-int i2c_set_bus_speed(struct udevice *bus, unsigned int speed);
+int dm_i2c_set_bus_speed(struct udevice *bus, unsigned int speed);
/**
- * i2c_get_bus_speed() - get the speed of a bus
+ * dm_i2c_get_bus_speed() - get the speed of a bus
*
* @bus: Bus to check
* @return speed of selected I2C bus in Hz, -ve on error
*/
-int i2c_get_bus_speed(struct udevice *bus);
+int dm_i2c_get_bus_speed(struct udevice *bus);
/**
* i2c_set_chip_flags() - set flags for a chip
*
* @offset_len: New offset length value (typically 1 or 2)
*/
-
int i2c_set_chip_offset_len(struct udevice *dev, uint offset_len);
+
+/**
+ * i2c_get_offset_len() - get the offset length for a chip
+ *
+ * @return: Current offset length value (typically 1 or 2)
+ */
+int i2c_get_chip_offset_len(struct udevice *dev);
+
/**
* i2c_deblock() - recover a bus that is in an unknown state
*
*/
int i2c_deblock(struct udevice *bus);
+#ifdef CONFIG_DM_I2C_COMPAT
+/**
+ * i2c_probe() - Compatibility function for driver model
+ *
+ * Calls dm_i2c_probe() on the current bus
+ */
+int i2c_probe(uint8_t chip_addr);
+
+/**
+ * i2c_read() - Compatibility function for driver model
+ *
+ * Calls dm_i2c_read() with the device corresponding to @chip_addr, and offset
+ * set to @addr. @alen must match the current setting for the device.
+ */
+int i2c_read(uint8_t chip_addr, unsigned int addr, int alen, uint8_t *buffer,
+ int len);
+
+/**
+ * i2c_write() - Compatibility function for driver model
+ *
+ * Calls dm_i2c_write() with the device corresponding to @chip_addr, and offset
+ * set to @addr. @alen must match the current setting for the device.
+ */
+int i2c_write(uint8_t chip_addr, unsigned int addr, int alen, uint8_t *buffer,
+ int len);
+
+/**
+ * i2c_get_bus_num_fdt() - Compatibility function for driver model
+ *
+ * @return the bus number associated with the given device tree node
+ */
+int i2c_get_bus_num_fdt(int node);
+
+/**
+ * i2c_get_bus_num() - Compatibility function for driver model
+ *
+ * @return the 'current' bus number
+ */
+unsigned int i2c_get_bus_num(void);
+
+/**
+ * i2c_set_bus_num() - Compatibility function for driver model
+ *
+ * Sets the 'current' bus
+ */
+int i2c_set_bus_num(unsigned int bus);
+
+static inline void I2C_SET_BUS(unsigned int bus)
+{
+ i2c_set_bus_num(bus);
+}
+
+static inline unsigned int I2C_GET_BUS(void)
+{
+ return i2c_get_bus_num();
+}
+
+/**
+ * i2c_init() - Compatibility function for driver model
+ *
+ * This function does nothing.
+ */
+void i2c_init(int speed, int slaveaddr);
+
+/**
+ * board_i2c_init() - Compatibility function for driver model
+ *
+ * @param blob Device tree blbo
+ * @return the number of I2C bus
+ */
+void board_i2c_init(const void *blob);
+
+/*
+ * Compatibility functions for driver model.
+ */
+uint8_t i2c_reg_read(uint8_t addr, uint8_t reg);
+void i2c_reg_write(uint8_t addr, uint8_t reg, uint8_t val);
+
+#endif
+
/*
* Not all of these flags are implemented in the U-Boot API
*/
* The bus speed value will be updated by the uclass if this function
* does not return an error. This method is optional - if it is not
* provided then the driver can read the speed from
- * bus->uclass_priv->speed_hz
+ * dev_get_uclass_priv(bus)->speed_hz
*
* @bus: Bus to adjust
* @speed: Requested speed in Hz
* Normally this can be provided by the uclass, but if you want your
* driver to check the bus speed by looking at the hardware, you can
* implement that here. This method is optional. This method would
- * normally be expected to return bus->uclass_priv->speed_hz.
+ * normally be expected to return dev_get_uclass_priv(bus)->speed_hz.
*
* @bus: Bus to check
* @return speed of selected I2C bus in Hz, -ve on error
*
* @bus: Bus to examine
* @chip_addr: Chip address for the new device
+ * @offset_len: Length of a register offset in bytes (normally 1)
* @devp: Returns pointer to new device if found or -ENODEV if not
* found
*/
-int i2c_get_chip(struct udevice *bus, uint chip_addr, struct udevice **devp);
+int i2c_get_chip(struct udevice *bus, uint chip_addr, uint offset_len,
+ struct udevice **devp);
/**
* i2c_get_chip() - get a device to use to access a chip on a bus number
*
* @busnum: Bus number to examine
* @chip_addr: Chip address for the new device
+ * @offset_len: Length of a register offset in bytes (normally 1)
* @devp: Returns pointer to new device if found or -ENODEV if not
* found
*/
-int i2c_get_chip_for_busnum(int busnum, int chip_addr, struct udevice **devp);
+int i2c_get_chip_for_busnum(int busnum, int chip_addr, uint offset_len,
+ struct udevice **devp);
/**
* i2c_chip_ofdata_to_platdata() - Decode standard I2C platform data
int i2c_chip_ofdata_to_platdata(const void *blob, int node,
struct dm_i2c_chip *chip);
-#endif
-
#ifndef CONFIG_DM_I2C
/*
projects / karo-tx-uboot.git / blobdiff