X-Git-Url: https://git.kernelconcepts.de/?p=karo-tx-uboot.git;a=blobdiff_plain;f=README;h=1130b4f3291628019b86aaf71183a2c6701888d0;hp=f0ffaf491cd9c204b24a49aacf4d9712148cdf32;hb=f15ea6e1d67782a1626d4a4922b6c20e380085e5;hpb=cb7ee1b98cac6baf244daefb1192adf5a47bc983

diff --git a/README b/README
index f0ffaf491c..1130b4f329 100644
--- a/README
+++ b/README
@@ -423,16 +423,50 @@ The following options need to be configured:
 		CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
 		This value denotes start offset of DSP CCSR space.
 
-		CONFIG_SYS_FSL_DDR_EMU
-		Specify emulator support for DDR. Some DDR features such as
-		deskew training are not available.
-
 - Generic CPU options:
 		CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
 
 		Defines the endianess of the CPU. Implementation of those
 		values is arch specific.
 
+		CONFIG_SYS_FSL_DDR
+		Freescale DDR driver in use. This type of DDR controller is
+		found in mpc83xx, mpc85xx, mpc86xx as well as some ARM core
+		SoCs.
+
+		CONFIG_SYS_FSL_DDR_ADDR
+		Freescale DDR memory-mapped register base.
+
+		CONFIG_SYS_FSL_DDR_EMU
+		Specify emulator support for DDR. Some DDR features such as
+		deskew training are not available.
+
+		CONFIG_SYS_FSL_DDRC_GEN1
+		Freescale DDR1 controller.
+
+		CONFIG_SYS_FSL_DDRC_GEN2
+		Freescale DDR2 controller.
+
+		CONFIG_SYS_FSL_DDRC_GEN3
+		Freescale DDR3 controller.
+
+		CONFIG_SYS_FSL_DDRC_ARM_GEN3
+		Freescale DDR3 controller for ARM-based SoCs.
+
+		CONFIG_SYS_FSL_DDR1
+		Board config to use DDR1. It can be enabled for SoCs with
+		Freescale DDR1 or DDR2 controllers, depending on the board
+		implemetation.
+
+		CONFIG_SYS_FSL_DDR2
+		Board config to use DDR2. It can be eanbeld for SoCs with
+		Freescale DDR2 or DDR3 controllers, depending on the board
+		implementation.
+
+		CONFIG_SYS_FSL_DDR3
+		Board config to use DDR3. It can be enabled for SoCs with
+		Freescale DDR3 controllers.
+
 - Intel Monahans options:
 		CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
 
@@ -1979,6 +2013,21 @@ CBFS (Coreboot Filesystem) support
 		kernel). Defining CONFIG_STATUS_LED enables this
 		feature in U-Boot.
 
+		Additional options:
+
+		CONFIG_GPIO_LED
+		The status LED can be connected to a GPIO pin.
+		In such cases, the gpio_led driver can be used as a
+		status LED backend implementation. Define CONFIG_GPIO_LED
+		to include the gpio_led driver in the U-Boot binary.
+
+		CONFIG_GPIO_LED_INVERTED_TABLE
+		Some GPIO connected LEDs may have inverted polarity in which
+		case the GPIO high value corresponds to LED off state and
+		GPIO low value corresponds to LED on state.
+		In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
+		with a list of GPIO LEDs that have inverted polarity.
+
 - CAN Support:	CONFIG_CAN_DRIVER
 
 		Defining CONFIG_CAN_DRIVER enables CAN driver support
@@ -2056,6 +2105,42 @@ CBFS (Coreboot Filesystem) support
 		  - CONFIG_SYS_RCAR_I2C3_SPEED for for the speed channel 3
 		  - CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS for number of i2c buses
 
+		- drivers/i2c/sh_i2c.c:
+		  - activate this driver with CONFIG_SYS_I2C_SH
+		  - This driver adds from 2 to 5 i2c buses
+
+		  - CONFIG_SYS_I2C_SH_BASE0 for setting the register channel 0
+		  - CONFIG_SYS_I2C_SH_SPEED0 for for the speed channel 0
+		  - CONFIG_SYS_I2C_SH_BASE1 for setting the register channel 1
+		  - CONFIG_SYS_I2C_SH_SPEED1 for for the speed channel 1
+		  - CONFIG_SYS_I2C_SH_BASE2 for setting the register channel 2
+		  - CONFIG_SYS_I2C_SH_SPEED2 for for the speed channel 2
+		  - CONFIG_SYS_I2C_SH_BASE3 for setting the register channel 3
+		  - CONFIG_SYS_I2C_SH_SPEED3 for for the speed channel 3
+		  - CONFIG_SYS_I2C_SH_BASE4 for setting the register channel 4
+		  - CONFIG_SYS_I2C_SH_SPEED4 for for the speed channel 4
+		  - CONFIG_SYS_I2C_SH_BASE5 for setting the register channel 5
+		  - CONFIG_SYS_I2C_SH_SPEED5 for for the speed channel 5
+		  - CONFIF_SYS_I2C_SH_NUM_CONTROLLERS for nummber of i2c buses
+
+		- drivers/i2c/omap24xx_i2c.c
+		  - activate this driver with CONFIG_SYS_I2C_OMAP24XX
+		  - CONFIG_SYS_OMAP24_I2C_SPEED speed channel 0
+		  - CONFIG_SYS_OMAP24_I2C_SLAVE slave addr channel 0
+		  - CONFIG_SYS_OMAP24_I2C_SPEED1 speed channel 1
+		  - CONFIG_SYS_OMAP24_I2C_SLAVE1 slave addr channel 1
+		  - CONFIG_SYS_OMAP24_I2C_SPEED2 speed channel 2
+		  - CONFIG_SYS_OMAP24_I2C_SLAVE2 slave addr channel 2
+		  - CONFIG_SYS_OMAP24_I2C_SPEED3 speed channel 3
+		  - CONFIG_SYS_OMAP24_I2C_SLAVE3 slave addr channel 3
+		  - CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4
+		  - CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4
+
+		- drivers/i2c/zynq_i2c.c
+		  - activate this driver with CONFIG_SYS_I2C_ZYNQ
+		  - set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting
+		  - set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr
+
 		additional defines:
 
 		CONFIG_SYS_NUM_I2C_BUSES
@@ -3162,7 +3247,7 @@ FIT uImage format:
 
 		CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
 		Set for the SPL on PPC mpc8xxx targets, support for
-		arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary.
+		drivers/ddr/fsl/libddr.o in SPL binary.
 
 		CONFIG_SPL_COMMON_INIT_DDR
 		Set for common ddr init with serial presence detect in