obj-y += nand_util.o
obj-y += nand_ecc.o
obj-y += nand_base.o
+obj-y += nand_timings.o
endif # not spl
#define PMECC_MAX_TIMEOUT_US (100 * 1000)
+/* Reserved bytes in oob area */
+#define PMECC_OOB_RESERVED_BYTES 2
+
#endif
static int onfi_timing_mode = NAND_DEFAULT_TIMINGS;
-/* We define a macro here that combines all interrupts this driver uses into
- * a single constant value, for convenience. */
+/*
+ * We define a macro here that combines all interrupts this driver uses into
+ * a single constant value, for convenience.
+ */
#define DENALI_IRQ_ALL (INTR_STATUS__DMA_CMD_COMP | \
INTR_STATUS__ECC_TRANSACTION_DONE | \
INTR_STATUS__ECC_ERR | \
INTR_STATUS__INT_ACT | \
INTR_STATUS__LOCKED_BLK)
-/* indicates whether or not the internal value for the flash bank is
- * valid or not */
+/*
+ * indicates whether or not the internal value for the flash bank is
+ * valid or not
+ */
#define CHIP_SELECT_INVALID -1
#define SUPPORT_8BITECC 1
*/
#define mtd_to_denali(m) container_of(m->priv, struct denali_nand_info, nand)
-/* These constants are defined by the driver to enable common driver
- * configuration options. */
+/*
+ * These constants are defined by the driver to enable common driver
+ * configuration options.
+ */
#define SPARE_ACCESS 0x41
#define MAIN_ACCESS 0x42
#define MAIN_SPARE_ACCESS 0x43
+#define PIPELINE_ACCESS 0x2000
#define DENALI_UNLOCK_START 0x10
#define DENALI_UNLOCK_END 0x11
#define ADDR_CYCLE 1
#define STATUS_CYCLE 2
-/* this is a helper macro that allows us to
- * format the bank into the proper bits for the controller */
+/*
+ * this is a helper macro that allows us to
+ * format the bank into the proper bits for the controller
+ */
#define BANK(x) ((x) << 24)
/* Interrupts are cleared by writing a 1 to the appropriate status bit */
* read/write data. The operation is performed by writing the address value
* of the command to the device memory followed by the data. This function
* abstracts this common operation.
-*/
+ */
static void index_addr(struct denali_nand_info *denali,
uint32_t address, uint32_t data)
{
*pdata = readl(denali->flash_mem + INDEX_DATA_REG);
}
-/* We need to buffer some data for some of the NAND core routines.
- * The operations manage buffering that data. */
+/*
+ * We need to buffer some data for some of the NAND core routines.
+ * The operations manage buffering that data.
+ */
static void reset_buf(struct denali_nand_info *denali)
{
denali->buf.head = 0;
static void reset_bank(struct denali_nand_info *denali)
{
uint32_t irq_status;
- uint32_t irq_mask = INTR_STATUS__RST_COMP |
- INTR_STATUS__TIME_OUT;
+ uint32_t irq_mask = INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT;
clear_interrupts(denali);
/* Reset the flash controller */
static uint32_t denali_nand_reset(struct denali_nand_info *denali)
{
- uint32_t i;
+ int i;
for (i = 0; i < denali->max_banks; i++)
writel(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT,
uint32_t twhr[6] = {120, 80, 80, 60, 60, 60};
uint32_t tcs[6] = {70, 35, 25, 25, 20, 15};
- uint32_t tclsrising = 1;
uint32_t data_invalid_rhoh, data_invalid_rloh, data_invalid;
uint32_t dv_window = 0;
uint32_t en_lo, en_hi;
data_invalid_rloh = (en_lo + en_hi) * CLK_X + trloh[mode];
- data_invalid =
- data_invalid_rhoh <
- data_invalid_rloh ? data_invalid_rhoh : data_invalid_rloh;
+ data_invalid = data_invalid_rhoh < data_invalid_rloh ?
+ data_invalid_rhoh : data_invalid_rloh;
dv_window = data_invalid - trea[mode];
acc_clks = DIV_ROUND_UP(trea[mode], CLK_X);
- while (((acc_clks * CLK_X) - trea[mode]) < 3)
+ while (acc_clks * CLK_X - trea[mode] < 3)
acc_clks++;
- if ((data_invalid - acc_clks * CLK_X) < 2)
+ if (data_invalid - acc_clks * CLK_X < 2)
debug("%s, Line %d: Warning!\n", __FILE__, __LINE__);
addr_2_data = DIV_ROUND_UP(tadl[mode], CLK_X);
re_2_re = DIV_ROUND_UP(trhz[mode], CLK_X);
we_2_re = DIV_ROUND_UP(twhr[mode], CLK_X);
cs_cnt = DIV_ROUND_UP((tcs[mode] - trp[mode]), CLK_X);
- if (!tclsrising)
- cs_cnt = DIV_ROUND_UP(tcs[mode], CLK_X);
if (cs_cnt == 0)
cs_cnt = 1;
if (tcea[mode]) {
- while (((cs_cnt * CLK_X) + trea[mode]) < tcea[mode])
+ while (cs_cnt * CLK_X + trea[mode] < tcea[mode])
cs_cnt++;
}
/* Sighting 3462430: Temporary hack for MT29F128G08CJABAWP:B */
- if ((readl(denali->flash_reg + MANUFACTURER_ID) == 0) &&
- (readl(denali->flash_reg + DEVICE_ID) == 0x88))
+ if (readl(denali->flash_reg + MANUFACTURER_ID) == 0 &&
+ readl(denali->flash_reg + DEVICE_ID) == 0x88)
acc_clks = 6;
writel(acc_clks, denali->flash_reg + ACC_CLKS);
static uint32_t get_onfi_nand_para(struct denali_nand_info *denali)
{
int i;
+
/*
* we needn't to do a reset here because driver has already
* reset all the banks before
nand_onfi_timing_set(denali, i);
- /* By now, all the ONFI devices we know support the page cache */
- /* rw feature. So here we enable the pipeline_rw_ahead feature */
+ /*
+ * By now, all the ONFI devices we know support the page cache
+ * rw feature. So here we enable the pipeline_rw_ahead feature
+ */
+
return 0;
}
{
uint32_t tmp;
- /* Workaround to fix a controller bug which reports a wrong */
- /* spare area size for some kind of Toshiba NAND device */
+ /*
+ * Workaround to fix a controller bug which reports a wrong
+ * spare area size for some kind of Toshiba NAND device
+ */
if ((readl(denali->flash_reg + DEVICE_MAIN_AREA_SIZE) == 4096) &&
(readl(denali->flash_reg + DEVICE_SPARE_AREA_SIZE) == 64)) {
writel(216, denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
writel(0, denali->flash_reg + DEVICE_WIDTH);
break;
default:
- debug("Spectra: Unknown Hynix NAND (Device ID: 0x%x)."
+ debug("Spectra: Unknown Hynix NAND (Device ID: 0x%x).\n"
"Will use default parameter values instead.\n",
device_id);
}
denali->total_used_banks = 1;
for (i = 0; i < denali->max_banks; i++) {
- index_addr(denali, (uint32_t)(MODE_11 | (i << 24) | 0), 0x90);
- index_addr(denali, (uint32_t)(MODE_11 | (i << 24) | 1), 0);
- index_addr_read_data(denali,
- (uint32_t)(MODE_11 | (i << 24) | 2),
- &id[i]);
+ index_addr(denali, MODE_11 | (i << 24) | 0, 0x90);
+ index_addr(denali, MODE_11 | (i << 24) | 1, 0);
+ index_addr_read_data(denali, MODE_11 | (i << 24) | 2, &id[i]);
if (i == 0) {
if (!(id[i] & 0x0ff))
static uint32_t denali_nand_timing_set(struct denali_nand_info *denali)
{
- uint32_t id_bytes[5], addr;
- uint8_t i, maf_id, device_id;
-
- /* Use read id method to get device ID and other
- * params. For some NAND chips, controller can't
- * report the correct device ID by reading from
- * DEVICE_ID register
- * */
- addr = (uint32_t)MODE_11 | BANK(denali->flash_bank);
- index_addr(denali, (uint32_t)addr | 0, 0x90);
- index_addr(denali, (uint32_t)addr | 1, 0);
- for (i = 0; i < 5; i++)
+ uint32_t id_bytes[8], addr;
+ uint8_t maf_id, device_id;
+ int i;
+
+ /*
+ * Use read id method to get device ID and other params.
+ * For some NAND chips, controller can't report the correct
+ * device ID by reading from DEVICE_ID register
+ */
+ addr = MODE_11 | BANK(denali->flash_bank);
+ index_addr(denali, addr | 0, 0x90);
+ index_addr(denali, addr | 1, 0);
+ for (i = 0; i < 8; i++)
index_addr_read_data(denali, addr | 2, &id_bytes[i]);
maf_id = id_bytes[0];
device_id = id_bytes[1];
detect_partition_feature(denali);
- /* If the user specified to override the default timings
+ /*
+ * If the user specified to override the default timings
* with a specific ONFI mode, we apply those changes here.
*/
if (onfi_timing_mode != NAND_DEFAULT_TIMINGS)
return 0;
}
-/* validation function to verify that the controlling software is making
+/*
+ * validation function to verify that the controlling software is making
* a valid request
*/
static inline bool is_flash_bank_valid(int flash_bank)
static void denali_irq_init(struct denali_nand_info *denali)
{
- uint32_t int_mask = 0;
+ uint32_t int_mask;
int i;
/* Disable global interrupts */
denali_irq_enable(denali, int_mask);
}
-/* This helper function setups the registers for ECC and whether or not
- * the spare area will be transferred. */
+/*
+ * This helper function setups the registers for ECC and whether or not
+ * the spare area will be transferred.
+ */
static void setup_ecc_for_xfer(struct denali_nand_info *denali, bool ecc_en,
bool transfer_spare)
{
- int ecc_en_flag = 0, transfer_spare_flag = 0;
+ int ecc_en_flag, transfer_spare_flag;
/* set ECC, transfer spare bits if needed */
ecc_en_flag = ecc_en ? ECC_ENABLE__FLAG : 0;
writel(transfer_spare_flag, denali->flash_reg + TRANSFER_SPARE_REG);
}
-/* sends a pipeline command operation to the controller. See the Denali NAND
+/*
+ * sends a pipeline command operation to the controller. See the Denali NAND
* controller's user guide for more information (section 4.2.3.6).
*/
static int denali_send_pipeline_cmd(struct denali_nand_info *denali,
- bool ecc_en, bool transfer_spare,
- int access_type, int op)
+ bool ecc_en, bool transfer_spare,
+ int access_type, int op)
{
uint32_t addr, cmd, irq_status;
static uint32_t page_count = 1;
setup_ecc_for_xfer(denali, ecc_en, transfer_spare);
- /* clear interrupts */
clear_interrupts(denali);
addr = BANK(denali->flash_bank) | denali->page;
/* helper function that simply writes a buffer to the flash */
static int write_data_to_flash_mem(struct denali_nand_info *denali,
- const uint8_t *buf, int len)
+ const uint8_t *buf, int len)
{
- uint32_t i = 0, *buf32;
+ uint32_t *buf32;
+ int i;
- /* verify that the len is a multiple of 4. see comment in
- * read_data_from_flash_mem() */
+ /*
+ * verify that the len is a multiple of 4.
+ * see comment in read_data_from_flash_mem()
+ */
BUG_ON((len % 4) != 0);
/* write the data to the flash memory */
/* helper function that simply reads a buffer from the flash */
static int read_data_from_flash_mem(struct denali_nand_info *denali,
- uint8_t *buf, int len)
+ uint8_t *buf, int len)
{
- uint32_t i, *buf32;
+ uint32_t *buf32;
+ int i;
/*
- * we assume that len will be a multiple of 4, if not
- * it would be nice to know about it ASAP rather than
- * have random failures...
- * This assumption is based on the fact that this
- * function is designed to be used to read flash pages,
- * which are typically multiples of 4...
+ * we assume that len will be a multiple of 4, if not it would be nice
+ * to know about it ASAP rather than have random failures...
+ * This assumption is based on the fact that this function is designed
+ * to be used to read flash pages, which are typically multiples of 4.
*/
-
BUG_ON((len % 4) != 0);
/* transfer the data from the flash */
static void read_oob_data(struct mtd_info *mtd, uint8_t *buf, int page)
{
struct denali_nand_info *denali = mtd_to_denali(mtd);
- uint32_t irq_mask = INTR_STATUS__LOAD_COMP,
- irq_status = 0, addr = 0x0, cmd = 0x0;
+ uint32_t irq_mask = INTR_STATUS__LOAD_COMP;
+ uint32_t irq_status, addr, cmd;
denali->page = page;
DENALI_READ) == 0) {
read_data_from_flash_mem(denali, buf, mtd->oobsize);
- /* wait for command to be accepted
- * can always use status0 bit as the mask is identical for each
- * bank. */
+ /*
+ * wait for command to be accepted
+ * can always use status0 bit as the
+ * mask is identical for each bank.
+ */
irq_status = wait_for_irq(denali, irq_mask);
if (irq_status == 0)
printf("page on OOB timeout %d\n", denali->page);
- /* We set the device back to MAIN_ACCESS here as I observed
+ /*
+ * We set the device back to MAIN_ACCESS here as I observed
* instability with the controller if you do a block erase
* and the last transaction was a SPARE_ACCESS. Block erase
* is reliable (according to the MTD test infrastructure)
}
}
-/* this function examines buffers to see if they contain data that
+/*
+ * this function examines buffers to see if they contain data that
* indicate that the buffer is part of an erased region of flash.
*/
static bool is_erased(uint8_t *buf, int len)
{
- int i = 0;
+ int i;
+
for (i = 0; i < len; i++)
if (buf[i] != 0xFF)
return false;
/* programs the controller to either enable/disable DMA transfers */
static void denali_enable_dma(struct denali_nand_info *denali, bool en)
{
- uint32_t reg_val = 0x0;
-
- if (en)
- reg_val = DMA_ENABLE__FLAG;
-
- writel(reg_val, denali->flash_reg + DMA_ENABLE);
+ writel(en ? DMA_ENABLE__FLAG : 0, denali->flash_reg + DMA_ENABLE);
readl(denali->flash_reg + DMA_ENABLE);
}
index_addr(denali, mode | denali->page, 0x2000 | op | page_count);
/* 2. set memory high address bits 23:8 */
- index_addr(denali, mode | ((uint32_t)(addr >> 16) << 8), 0x2200);
+ index_addr(denali, mode | ((addr >> 16) << 8), 0x2200);
/* 3. set memory low address bits 23:8 */
- index_addr(denali, mode | ((uint32_t)addr << 8), 0x2300);
+ index_addr(denali, mode | ((addr & 0xffff) << 8), 0x2300);
- /* 4. interrupt when complete, burst len = 64 bytes*/
+ /* 4. interrupt when complete, burst len = 64 bytes */
index_addr(denali, mode | 0x14000, 0x2400);
#endif
}
{
struct denali_nand_info *denali = mtd_to_denali(mtd);
int status = denali->status;
+
denali->status = 0;
return status;
}
-static void denali_erase(struct mtd_info *mtd, int page)
+static int denali_erase(struct mtd_info *mtd, int page)
{
struct denali_nand_info *denali = mtd_to_denali(mtd);
+
uint32_t cmd, irq_status;
- /* clear interrupts */
clear_interrupts(denali);
/* setup page read request for access type */
if (irq_status & INTR_STATUS__ERASE_FAIL ||
irq_status & INTR_STATUS__LOCKED_BLK)
- denali->status = NAND_STATUS_FAIL;
- else
- denali->status = 0;
+ return NAND_STATUS_FAIL;
+
+ return 0;
}
static void denali_cmdfunc(struct mtd_info *mtd, unsigned int cmd, int col,
case NAND_CMD_READID:
case NAND_CMD_PARAM:
reset_buf(denali);
- /* sometimes ManufactureId read from register is not right
+ /*
+ * sometimes ManufactureId read from register is not right
* e.g. some of Micron MT29F32G08QAA MLC NAND chips
* So here we send READID cmd to NAND insteand
- * */
+ */
addr = MODE_11 | BANK(denali->flash_bank);
index_addr(denali, addr | 0, cmd);
index_addr(denali, addr | 1, col & 0xFF);
denali->nand.ecc.mode = NAND_ECC_HW;
denali->nand.ecc.size = CONFIG_NAND_DENALI_ECC_SIZE;
+ /* no subpage writes on denali */
+ denali->nand.options |= NAND_NO_SUBPAGE_WRITE;
+
/*
* Tell driver the ecc strength. This register may be already set
* correctly. So we read this value out.
* SPDX-License-Identifier: GPL-2.0+
*/
+#ifndef __DENALI_H__
+#define __DENALI_H__
+
#include <linux/mtd/nand.h>
#define DEVICE_RESET 0x0
#define CUSTOM_CONF_PARAMS 0
-#ifndef _LLD_NAND_
-#define _LLD_NAND_
-
#define INDEX_CTRL_REG 0x0
#define INDEX_DATA_REG 0x10
uint32_t max_banks;
};
-#endif /*_LLD_NAND_*/
+#endif /* __DENALI_H__ */
return read_page(mtd, nand, buf, page, 1);
}
-static void docg4_erase_block(struct mtd_info *mtd, int page)
+static int docg4_erase_block(struct mtd_info *mtd, int page)
{
struct nand_chip *nand = mtd->priv;
struct docg4_priv *doc = nand->priv;
write_nop(docptr);
poll_status(docptr);
write_nop(docptr);
+
+ return nand->waitfunc(mtd, nand);
}
static int read_factory_bbt(struct mtd_info *mtd)
nand->read_buf = docg4_read_buf;
nand->write_buf = docg4_write_buf16;
nand->scan_bbt = nand_default_bbt;
- nand->erase_cmd = docg4_erase_block;
+ nand->erase = docg4_erase_block;
nand->ecc.read_page = docg4_read_page;
nand->ecc.write_page = docg4_write_page;
nand->ecc.read_page_raw = docg4_read_page_raw;
static struct fsl_elbc_ctrl *elbc_ctrl;
+/* ECC will be calculated automatically, and errors will be detected in
+ * waitfunc.
+ */
+static int fsl_elbc_write_subpage(struct mtd_info *mtd, struct nand_chip *chip,
+ uint32_t offset, uint32_t data_len,
+ const uint8_t *buf, int oob_required)
+{
+ fsl_elbc_write_buf(mtd, buf, mtd->writesize);
+ fsl_elbc_write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ return 0;
+}
+
static void fsl_elbc_ctrl_init(void)
{
elbc_ctrl = kzalloc(sizeof(*elbc_ctrl), GFP_KERNEL);
nand->ecc.read_page = fsl_elbc_read_page;
nand->ecc.write_page = fsl_elbc_write_page;
+ nand->ecc.write_subpage = fsl_elbc_write_subpage;
priv->fmr = (15 << FMR_CWTO_SHIFT) | (2 << FMR_AL_SHIFT);
/* device info */
struct fsl_ifc regs;
- uint8_t __iomem *addr; /* Address of assigned IFC buffer */
+ void __iomem *addr; /* Address of assigned IFC buffer */
unsigned int cs_nand; /* On which chipsel NAND is connected */
unsigned int page; /* Last page written to / read from */
unsigned int read_bytes; /* Number of bytes read during command */
fsl_ifc_run_command(mtd);
- /* Chip sometimes reporting write protect even when it's not */
- out_8(ctrl->addr, in_8(ctrl->addr) | NAND_STATUS_WP);
+ /*
+ * The chip always seems to report that it is
+ * write-protected, even when it is not.
+ */
+ if (chip->options & NAND_BUSWIDTH_16)
+ ifc_out16(ctrl->addr,
+ ifc_in16(ctrl->addr) | NAND_STATUS_WP);
+ else
+ out_8(ctrl->addr, in_8(ctrl->addr) | NAND_STATUS_WP);
return;
case NAND_CMD_RESET:
len = bufsize - ctrl->index;
}
- memcpy_toio(&ctrl->addr[ctrl->index], buf, len);
+ memcpy_toio(ctrl->addr + ctrl->index, buf, len);
ctrl->index += len;
}
struct nand_chip *chip = mtd->priv;
struct fsl_ifc_mtd *priv = chip->priv;
struct fsl_ifc_ctrl *ctrl = priv->ctrl;
+ unsigned int offset;
- /* If there are still bytes in the IFC buffer, then use the
- * next byte. */
- if (ctrl->index < ctrl->read_bytes)
- return in_8(&ctrl->addr[ctrl->index++]);
+ /*
+ * If there are still bytes in the IFC buffer, then use the
+ * next byte.
+ */
+ if (ctrl->index < ctrl->read_bytes) {
+ offset = ctrl->index++;
+ return in_8(ctrl->addr + offset);
+ }
printf("%s beyond end of buffer\n", __func__);
return ERR_BYTE;
* next byte.
*/
if (ctrl->index < ctrl->read_bytes) {
- data = ifc_in16((uint16_t *)&ctrl->
- addr[ctrl->index]);
+ data = ifc_in16(ctrl->addr + ctrl->index);
ctrl->index += 2;
return (uint8_t)data;
}
return;
avail = min((unsigned int)len, ctrl->read_bytes - ctrl->index);
- memcpy_fromio(buf, &ctrl->addr[ctrl->index], avail);
+ memcpy_fromio(buf, ctrl->addr + ctrl->index, avail);
ctrl->index += avail;
if (len > avail)
#include <asm/io.h>
#include <asm/errno.h>
-/*
- * CONFIG_SYS_NAND_RESET_CNT is used as a timeout mechanism when resetting
- * a flash. NAND flash is initialized prior to interrupts so standard timers
- * can't be used. CONFIG_SYS_NAND_RESET_CNT should be set to a value
- * which is greater than (max NAND reset time / NAND status read time).
- * A conservative default of 200000 (500 us / 25 ns) is used as a default.
- */
-#ifndef CONFIG_SYS_NAND_RESET_CNT
-#define CONFIG_SYS_NAND_RESET_CNT 200000
-#endif
-
static bool is_module_text_address(unsigned long addr) {return 0;}
/* Define default oob placement schemes for large and small page devices */
}
/**
- * nand_read_byte16 - [DEFAULT] read one byte endianness aware from the chip
* nand_read_byte16 - [DEFAULT] read one byte endianness aware from the chip
* @mtd: MTD device structure
*
uint8_t buf[2] = { 0, 0 };
int ret = 0, res, i = 0;
- ops.datbuf = NULL;
+ memset(&ops, 0, sizeof(ops));
ops.oobbuf = buf;
ops.ooboffs = chip->badblockpos;
if (chip->options & NAND_BUSWIDTH_16) {
}
/**
- * nand_block_checkbad - [GENERIC] Check if a block is marked bad
+ * nand_block_isreserved - [GENERIC] Check if a block is marked reserved.
* @mtd: MTD device structure
* @ofs: offset from device start
*
- * Check if the block is mark as reserved.
+ * Check if the block is marked as reserved.
*/
static int nand_block_isreserved(struct mtd_info *mtd, loff_t ofs)
{
}
EXPORT_SYMBOL_GPL(nand_wait_ready);
+/**
+ * nand_wait_status_ready - [GENERIC] Wait for the ready status after commands.
+ * @mtd: MTD device structure
+ * @timeo: Timeout in ms
+ *
+ * Wait for status ready (i.e. command done) or timeout.
+ */
+static void nand_wait_status_ready(struct mtd_info *mtd, unsigned long timeo)
+{
+ register struct nand_chip *chip = mtd->priv;
+ u32 time_start;
+
+ timeo = (CONFIG_SYS_HZ * timeo) / 1000;
+ time_start = get_timer(0);
+ while (get_timer(time_start) < timeo) {
+ if ((chip->read_byte(mtd) & NAND_STATUS_READY))
+ break;
+ WATCHDOG_RESET();
+ }
+};
+
/**
* nand_command - [DEFAULT] Send command to NAND device
* @mtd: MTD device structure
{
register struct nand_chip *chip = mtd->priv;
int ctrl = NAND_CTRL_CLE | NAND_CTRL_CHANGE;
- uint32_t rst_sts_cnt = CONFIG_SYS_NAND_RESET_CNT;
/* Write out the command to the device */
if (command == NAND_CMD_SEQIN) {
NAND_CTRL_CLE | NAND_CTRL_CHANGE);
chip->cmd_ctrl(mtd,
NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
- while (!(chip->read_byte(mtd) & NAND_STATUS_READY) &&
- (rst_sts_cnt--));
+ /* EZ-NAND can take upto 250ms as per ONFi v4.0 */
+ nand_wait_status_ready(mtd, 250);
return;
/* This applies to read commands */
int column, int page_addr)
{
register struct nand_chip *chip = mtd->priv;
- uint32_t rst_sts_cnt = CONFIG_SYS_NAND_RESET_CNT;
/* Emulate NAND_CMD_READOOB */
if (command == NAND_CMD_READOOB) {
/*
* Program and erase have their own busy handlers status, sequential
- * in, and deplete1 need no delay.
+ * in and status need no delay.
*/
switch (command) {
NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
chip->cmd_ctrl(mtd, NAND_CMD_NONE,
NAND_NCE | NAND_CTRL_CHANGE);
- while (!(chip->read_byte(mtd) & NAND_STATUS_READY) &&
- (rst_sts_cnt--));
+ /* EZ-NAND can take upto 250ms as per ONFi v4.0 */
+ nand_wait_status_ready(mtd, 250);
return;
case NAND_CMD_RNDOUT:
* ecc.pos. Let's make sure that there are no gaps in ECC positions.
*/
for (i = 0; i < eccfrag_len - 1; i++) {
- if (eccpos[i + start_step * chip->ecc.bytes] + 1 !=
- eccpos[i + start_step * chip->ecc.bytes + 1]) {
+ if (eccpos[i + index] + 1 != eccpos[i + index + 1]) {
gaps = 1;
break;
}
mtd->oobavail : mtd->oobsize;
uint8_t *bufpoi, *oob, *buf;
+ int use_bufpoi;
unsigned int max_bitflips = 0;
int retry_mode = 0;
bool ecc_fail = false;
bytes = min(mtd->writesize - col, readlen);
aligned = (bytes == mtd->writesize);
+ if (!aligned)
+ use_bufpoi = 1;
+ else
+ use_bufpoi = 0;
+
/* Is the current page in the buffer? */
if (realpage != chip->pagebuf || oob) {
- bufpoi = aligned ? buf : chip->buffers->databuf;
+ bufpoi = use_bufpoi ? chip->buffers->databuf : buf;
+
+ if (use_bufpoi && aligned)
+ pr_debug("%s: using read bounce buffer for buf@%p\n",
+ __func__, buf);
read_retry:
chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page);
ret = chip->ecc.read_page(mtd, chip, bufpoi,
oob_required, page);
if (ret < 0) {
- if (!aligned)
+ if (use_bufpoi)
/* Invalidate page cache */
chip->pagebuf = -1;
break;
max_bitflips = max_t(unsigned int, max_bitflips, ret);
/* Transfer not aligned data */
- if (!aligned) {
+ if (use_bufpoi) {
if (!NAND_HAS_SUBPAGE_READ(chip) && !oob &&
!(mtd->ecc_stats.failed - ecc_failures) &&
(ops->mode != MTD_OPS_RAW)) {
int ret;
nand_get_device(mtd, FL_READING);
+ memset(&ops, 0, sizeof(ops));
ops.len = len;
ops.datbuf = buf;
- ops.oobbuf = NULL;
ops.mode = MTD_OPS_PLACE_OOB;
ret = nand_do_read_ops(mtd, from, &ops);
*retlen = ops.retlen;
static int nand_read_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
int page)
{
- uint8_t *buf = chip->oob_poi;
int length = mtd->oobsize;
int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad;
int eccsize = chip->ecc.size;
- uint8_t *bufpoi = buf;
+ uint8_t *bufpoi = chip->oob_poi;
int i, toread, sndrnd = 0, pos;
chip->cmdfunc(mtd, NAND_CMD_READ0, chip->ecc.size, page);
/**
- * nand_write_subpage_hwecc - [REPLACABLE] hardware ECC based subpage write
+ * nand_write_subpage_hwecc - [REPLACEABLE] hardware ECC based subpage write
* @mtd: mtd info structure
* @chip: nand chip info structure
* @offset: column address of subpage within the page
blockmask = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1;
/* Invalidate the page cache, when we write to the cached page */
- if (to <= (chip->pagebuf << chip->page_shift) &&
- (chip->pagebuf << chip->page_shift) < (to + ops->len))
+ if (to <= ((loff_t)chip->pagebuf << chip->page_shift) &&
+ ((loff_t)chip->pagebuf << chip->page_shift) < (to + ops->len))
chip->pagebuf = -1;
/* Don't allow multipage oob writes with offset */
int bytes = mtd->writesize;
int cached = writelen > bytes && page != blockmask;
uint8_t *wbuf = buf;
+ int use_bufpoi;
+ int part_pagewr = (column || writelen < (mtd->writesize - 1));
+
+ if (part_pagewr)
+ use_bufpoi = 1;
+ else
+ use_bufpoi = 0;
WATCHDOG_RESET();
- /* Partial page write? */
- if (unlikely(column || writelen < (mtd->writesize - 1))) {
+ /* Partial page write?, or need to use bounce buffer */
+ if (use_bufpoi) {
+ pr_debug("%s: using write bounce buffer for buf@%p\n",
+ __func__, buf);
cached = 0;
- bytes = min_t(int, bytes - column, (int) writelen);
+ if (part_pagewr)
+ bytes = min_t(int, bytes - column, writelen);
chip->pagebuf = -1;
memset(chip->buffers->databuf, 0xff, mtd->writesize);
memcpy(&chip->buffers->databuf[column], buf, bytes);
/* Grab the device */
panic_nand_get_device(chip, mtd, FL_WRITING);
+ memset(&ops, 0, sizeof(ops));
ops.len = len;
ops.datbuf = (uint8_t *)buf;
- ops.oobbuf = NULL;
ops.mode = MTD_OPS_PLACE_OOB;
ret = nand_do_write_ops(mtd, to, &ops);
int ret;
nand_get_device(mtd, FL_WRITING);
+ memset(&ops, 0, sizeof(ops));
ops.len = len;
ops.datbuf = (uint8_t *)buf;
- ops.oobbuf = NULL;
ops.mode = MTD_OPS_PLACE_OOB;
ret = nand_do_write_ops(mtd, to, &ops);
*retlen = ops.retlen;
}
/**
- * single_erase_cmd - [GENERIC] NAND standard block erase command function
+ * single_erase - [GENERIC] NAND standard block erase command function
* @mtd: MTD device structure
* @page: the page address of the block which will be erased
*
- * Standard erase command for NAND chips.
+ * Standard erase command for NAND chips. Returns NAND status.
*/
-static void single_erase_cmd(struct mtd_info *mtd, int page)
+static int single_erase(struct mtd_info *mtd, int page)
{
struct nand_chip *chip = mtd->priv;
/* Send commands to erase a block */
chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page);
chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1);
+
+ return chip->waitfunc(mtd, chip);
}
/**
(page + pages_per_block))
chip->pagebuf = -1;
- chip->erase_cmd(mtd, page & chip->pagemask);
-
- status = chip->waitfunc(mtd, chip);
+ status = chip->erase(mtd, page & chip->pagemask);
/*
* See if operation failed and additional status checks are
return 0;
}
-
/* Set default functions */
static void nand_set_defaults(struct nand_chip *chip, int busw)
{
chip->options |= type->options;
chip->ecc_strength_ds = NAND_ECC_STRENGTH(type);
chip->ecc_step_ds = NAND_ECC_STEP(type);
+ chip->onfi_timing_mode_default =
+ type->onfi_timing_mode_default;
*busw = type->options & NAND_BUSWIDTH_16;
chip->onfi_version = 0;
if (!type->name || !type->pagesize) {
- /* Check is chip is ONFI compliant */
+ /* Check if the chip is ONFI compliant */
if (nand_flash_detect_onfi(mtd, chip, &busw))
goto ident_done;
}
chip->badblockbits = 8;
- chip->erase_cmd = single_erase_cmd;
+ chip->erase = single_erase;
/* Do not replace user supplied command function! */
if (mtd->writesize > 512 && chip->cmdfunc == nand_command)
type->name);
#endif
- pr_info("%dMiB, %s, page size: %d, OOB size: %d\n",
+ pr_info("%d MiB, %s, erase size: %d KiB, page size: %d, OOB size: %d\n",
(int)(chip->chipsize >> 20), nand_is_slc(chip) ? "SLC" : "MLC",
- mtd->writesize, mtd->oobsize);
+ mtd->erasesize >> 10, mtd->writesize, mtd->oobsize);
return type;
}
}
EXPORT_SYMBOL(nand_scan_ident);
+/*
+ * Check if the chip configuration meet the datasheet requirements.
+
+ * If our configuration corrects A bits per B bytes and the minimum
+ * required correction level is X bits per Y bytes, then we must ensure
+ * both of the following are true:
+ *
+ * (1) A / B >= X / Y
+ * (2) A >= X
+ *
+ * Requirement (1) ensures we can correct for the required bitflip density.
+ * Requirement (2) ensures we can correct even when all bitflips are clumped
+ * in the same sector.
+ */
+static bool nand_ecc_strength_good(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct nand_ecc_ctrl *ecc = &chip->ecc;
+ int corr, ds_corr;
+
+ if (ecc->size == 0 || chip->ecc_step_ds == 0)
+ /* Not enough information */
+ return true;
+
+ /*
+ * We get the number of corrected bits per page to compare
+ * the correction density.
+ */
+ corr = (mtd->writesize * ecc->strength) / ecc->size;
+ ds_corr = (mtd->writesize * chip->ecc_strength_ds) / chip->ecc_step_ds;
+
+ return corr >= ds_corr && ecc->strength >= chip->ecc_strength_ds;
+}
/**
* nand_scan_tail - [NAND Interface] Scan for the NAND device
case NAND_ECC_HW_OOB_FIRST:
/* Similar to NAND_ECC_HW, but a separate read_page handle */
if (!ecc->calculate || !ecc->correct || !ecc->hwctl) {
- pr_warn("No ECC functions supplied; "
- "hardware ECC not possible\n");
+ pr_warn("No ECC functions supplied; hardware ECC not possible\n");
BUG();
}
if (!ecc->read_page)
ecc->read_page == nand_read_page_hwecc ||
!ecc->write_page ||
ecc->write_page == nand_write_page_hwecc)) {
- pr_warn("No ECC functions supplied; "
- "hardware ECC not possible\n");
+ pr_warn("No ECC functions supplied; hardware ECC not possible\n");
BUG();
}
/* Use standard syndrome read/write page function? */
}
break;
}
- pr_warn("%d byte HW ECC not possible on "
- "%d byte page size, fallback to SW ECC\n",
- ecc->size, mtd->writesize);
+ pr_warn("%d byte HW ECC not possible on %d byte page size, fallback to SW ECC\n",
+ ecc->size, mtd->writesize);
ecc->mode = NAND_ECC_SOFT;
case NAND_ECC_SOFT:
ecc->read_oob = nand_read_oob_std;
ecc->write_oob = nand_write_oob_std;
/*
- * Board driver should supply ecc.size and ecc.bytes values to
- * select how many bits are correctable; see nand_bch_init()
- * for details. Otherwise, default to 4 bits for large page
- * devices.
+ * Board driver should supply ecc.size and ecc.strength values
+ * to select how many bits are correctable. Otherwise, default
+ * to 4 bits for large page devices.
*/
if (!ecc->size && (mtd->oobsize >= 64)) {
ecc->size = 512;
- ecc->bytes = 7;
+ ecc->strength = 4;
}
+
+ /* See nand_bch_init() for details. */
+ ecc->bytes = DIV_ROUND_UP(
+ ecc->strength * fls(8 * ecc->size), 8);
ecc->priv = nand_bch_init(mtd, ecc->size, ecc->bytes,
&ecc->layout);
if (!ecc->priv) {
pr_warn("BCH ECC initialization failed!\n");
BUG();
}
- ecc->strength = ecc->bytes * 8 / fls(8 * ecc->size);
break;
case NAND_ECC_NONE:
- pr_warn("NAND_ECC_NONE selected by board driver. "
- "This is not recommended!\n");
+ pr_warn("NAND_ECC_NONE selected by board driver. This is not recommended!\n");
ecc->read_page = nand_read_page_raw;
ecc->write_page = nand_write_page_raw;
ecc->read_oob = nand_read_oob_std;
ecc->layout->oobavail += ecc->layout->oobfree[i].length;
mtd->oobavail = ecc->layout->oobavail;
+ /* ECC sanity check: warn if it's too weak */
+ if (!nand_ecc_strength_good(mtd))
+ pr_warn("WARNING: %s: the ECC used on your system is too weak compared to the one required by the NAND chip\n",
+ mtd->name);
+
/*
* Set the number of read / write steps for one page depending on ECC
* mode.
chip->pagebuf = -1;
/* Large page NAND with SOFT_ECC should support subpage reads */
- if ((ecc->mode == NAND_ECC_SOFT) && (chip->page_shift > 9))
- chip->options |= NAND_SUBPAGE_READ;
+ switch (ecc->mode) {
+ case NAND_ECC_SOFT:
+ case NAND_ECC_SOFT_BCH:
+ if (chip->page_shift > 9)
+ chip->options |= NAND_SUBPAGE_READ;
+ break;
+
+ default:
+ break;
+ }
/* Fill in remaining MTD driver data */
mtd->type = nand_is_slc(chip) ? MTD_NANDFLASH : MTD_MLCNANDFLASH;
* properly set.
*/
if (!mtd->bitflip_threshold)
- mtd->bitflip_threshold = mtd->ecc_strength;
+ mtd->bitflip_threshold = DIV_ROUND_UP(mtd->ecc_strength * 3, 4);
return 0;
}
res = mtd_read(mtd, from, len, &retlen, buf);
if (res < 0) {
if (mtd_is_eccerr(res)) {
- pr_info("nand_bbt: ECC error in BBT at "
- "0x%012llx\n", from & ~mtd->writesize);
+ pr_info("nand_bbt: ECC error in BBT at 0x%012llx\n",
+ from & ~mtd->writesize);
return res;
} else if (mtd_is_bitflip(res)) {
- pr_info("nand_bbt: corrected error in BBT at "
- "0x%012llx\n", from & ~mtd->writesize);
+ pr_info("nand_bbt: corrected error in BBT at 0x%012llx\n",
+ from & ~mtd->writesize);
ret = res;
} else {
pr_info("nand_bbt: error reading BBT\n");
if (td->pages[i] == -1)
pr_warn("Bad block table not found for chip %d\n", i);
else
- pr_info("Bad block table found at page %d, version "
- "0x%02X\n", td->pages[i], td->version[i]);
+ pr_info("Bad block table found at page %d, version 0x%02X\n",
+ td->pages[i], td->version[i]);
}
return 0;
}
res = mtd_read(mtd, to, len, &retlen, buf);
if (res < 0) {
if (retlen != len) {
- pr_info("nand_bbt: error reading block "
- "for writing the bad block table\n");
+ pr_info("nand_bbt: error reading block for writing the bad block table\n");
return res;
}
- pr_warn("nand_bbt: ECC error while reading "
- "block for writing bad block table\n");
+ pr_warn("nand_bbt: ECC error while reading block for writing bad block table\n");
}
/* Read oob data */
ops.ooblen = (len >> this->page_shift) * mtd->oobsize;
int nand_default_bbt(struct mtd_info *mtd)
{
struct nand_chip *this = mtd->priv;
+ int ret;
/* Is a flash based bad block table requested? */
if (this->bbt_options & NAND_BBT_USE_FLASH) {
this->bbt_md = NULL;
}
- if (!this->badblock_pattern)
- nand_create_badblock_pattern(this);
+ if (!this->badblock_pattern) {
+ ret = nand_create_badblock_pattern(this);
+ if (ret)
+ return ret;
+ }
return nand_scan_bbt(mtd, this->badblock_pattern);
}
block = (int)(offs >> this->bbt_erase_shift);
res = bbt_get_entry(this, block);
- pr_debug("nand_isbad_bbt(): bbt info for offs 0x%08x: "
- "(block %d) 0x%02x\n",
- (unsigned int)offs, block, res);
+ pr_debug("nand_isbad_bbt(): bbt info for offs 0x%08x: (block %d) 0x%02x\n",
+ (unsigned int)offs, block, res);
switch (res) {
case BBT_BLOCK_GOOD:
{"SDTNRGAMA 64G 3.3V 8-bit",
{ .id = {0x45, 0xde, 0x94, 0x93, 0x76, 0x50} },
SZ_16K, SZ_8K, SZ_4M, 0, 6, 1280, NAND_ECC_INFO(40, SZ_1K) },
+ {"H27UCG8T2ATR-BC 64G 3.3V 8-bit",
+ { .id = {0xad, 0xde, 0x94, 0xda, 0x74, 0xc4} },
+ SZ_8K, SZ_8K, SZ_2M, 0, 6, 640, NAND_ECC_INFO(40, SZ_1K),
+ 4 },
LEGACY_ID_NAND("NAND 4MiB 5V 8-bit", 0x6B, 4, SZ_8K, SP_OPTIONS),
LEGACY_ID_NAND("NAND 4MiB 3,3V 8-bit", 0xE3, 4, SZ_8K, SP_OPTIONS),
{NAND_MFR_EON, "Eon"},
{NAND_MFR_SANDISK, "SanDisk"},
{NAND_MFR_INTEL, "Intel"},
+ {NAND_MFR_ATO, "ATO"},
{0x0, "Unknown"}
};
--- /dev/null
+/*
+ * Copyright (C) 2014 Free Electrons
+ *
+ * Author: Boris BREZILLON <boris.brezillon@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <common.h>
+#include <linux/kernel.h>
+#include <linux/mtd/nand.h>
+
+static const struct nand_sdr_timings onfi_sdr_timings[] = {
+ /* Mode 0 */
+ {
+ .tADL_min = 200000,
+ .tALH_min = 20000,
+ .tALS_min = 50000,
+ .tAR_min = 25000,
+ .tCEA_max = 100000,
+ .tCEH_min = 20000,
+ .tCH_min = 20000,
+ .tCHZ_max = 100000,
+ .tCLH_min = 20000,
+ .tCLR_min = 20000,
+ .tCLS_min = 50000,
+ .tCOH_min = 0,
+ .tCS_min = 70000,
+ .tDH_min = 20000,
+ .tDS_min = 40000,
+ .tFEAT_max = 1000000,
+ .tIR_min = 10000,
+ .tITC_max = 1000000,
+ .tRC_min = 100000,
+ .tREA_max = 40000,
+ .tREH_min = 30000,
+ .tRHOH_min = 0,
+ .tRHW_min = 200000,
+ .tRHZ_max = 200000,
+ .tRLOH_min = 0,
+ .tRP_min = 50000,
+ .tRST_max = 250000000000ULL,
+ .tWB_max = 200000,
+ .tRR_min = 40000,
+ .tWC_min = 100000,
+ .tWH_min = 30000,
+ .tWHR_min = 120000,
+ .tWP_min = 50000,
+ .tWW_min = 100000,
+ },
+ /* Mode 1 */
+ {
+ .tADL_min = 100000,
+ .tALH_min = 10000,
+ .tALS_min = 25000,
+ .tAR_min = 10000,
+ .tCEA_max = 45000,
+ .tCEH_min = 20000,
+ .tCH_min = 10000,
+ .tCHZ_max = 50000,
+ .tCLH_min = 10000,
+ .tCLR_min = 10000,
+ .tCLS_min = 25000,
+ .tCOH_min = 15000,
+ .tCS_min = 35000,
+ .tDH_min = 10000,
+ .tDS_min = 20000,
+ .tFEAT_max = 1000000,
+ .tIR_min = 0,
+ .tITC_max = 1000000,
+ .tRC_min = 50000,
+ .tREA_max = 30000,
+ .tREH_min = 15000,
+ .tRHOH_min = 15000,
+ .tRHW_min = 100000,
+ .tRHZ_max = 100000,
+ .tRLOH_min = 0,
+ .tRP_min = 25000,
+ .tRR_min = 20000,
+ .tRST_max = 500000000,
+ .tWB_max = 100000,
+ .tWC_min = 45000,
+ .tWH_min = 15000,
+ .tWHR_min = 80000,
+ .tWP_min = 25000,
+ .tWW_min = 100000,
+ },
+ /* Mode 2 */
+ {
+ .tADL_min = 100000,
+ .tALH_min = 10000,
+ .tALS_min = 15000,
+ .tAR_min = 10000,
+ .tCEA_max = 30000,
+ .tCEH_min = 20000,
+ .tCH_min = 10000,
+ .tCHZ_max = 50000,
+ .tCLH_min = 10000,
+ .tCLR_min = 10000,
+ .tCLS_min = 15000,
+ .tCOH_min = 15000,
+ .tCS_min = 25000,
+ .tDH_min = 5000,
+ .tDS_min = 15000,
+ .tFEAT_max = 1000000,
+ .tIR_min = 0,
+ .tITC_max = 1000000,
+ .tRC_min = 35000,
+ .tREA_max = 25000,
+ .tREH_min = 15000,
+ .tRHOH_min = 15000,
+ .tRHW_min = 100000,
+ .tRHZ_max = 100000,
+ .tRLOH_min = 0,
+ .tRR_min = 20000,
+ .tRST_max = 500000000,
+ .tWB_max = 100000,
+ .tRP_min = 17000,
+ .tWC_min = 35000,
+ .tWH_min = 15000,
+ .tWHR_min = 80000,
+ .tWP_min = 17000,
+ .tWW_min = 100000,
+ },
+ /* Mode 3 */
+ {
+ .tADL_min = 100000,
+ .tALH_min = 5000,
+ .tALS_min = 10000,
+ .tAR_min = 10000,
+ .tCEA_max = 25000,
+ .tCEH_min = 20000,
+ .tCH_min = 5000,
+ .tCHZ_max = 50000,
+ .tCLH_min = 5000,
+ .tCLR_min = 10000,
+ .tCLS_min = 10000,
+ .tCOH_min = 15000,
+ .tCS_min = 25000,
+ .tDH_min = 5000,
+ .tDS_min = 10000,
+ .tFEAT_max = 1000000,
+ .tIR_min = 0,
+ .tITC_max = 1000000,
+ .tRC_min = 30000,
+ .tREA_max = 20000,
+ .tREH_min = 10000,
+ .tRHOH_min = 15000,
+ .tRHW_min = 100000,
+ .tRHZ_max = 100000,
+ .tRLOH_min = 0,
+ .tRP_min = 15000,
+ .tRR_min = 20000,
+ .tRST_max = 500000000,
+ .tWB_max = 100000,
+ .tWC_min = 30000,
+ .tWH_min = 10000,
+ .tWHR_min = 80000,
+ .tWP_min = 15000,
+ .tWW_min = 100000,
+ },
+ /* Mode 4 */
+ {
+ .tADL_min = 70000,
+ .tALH_min = 5000,
+ .tALS_min = 10000,
+ .tAR_min = 10000,
+ .tCEA_max = 25000,
+ .tCEH_min = 20000,
+ .tCH_min = 5000,
+ .tCHZ_max = 30000,
+ .tCLH_min = 5000,
+ .tCLR_min = 10000,
+ .tCLS_min = 10000,
+ .tCOH_min = 15000,
+ .tCS_min = 20000,
+ .tDH_min = 5000,
+ .tDS_min = 10000,
+ .tFEAT_max = 1000000,
+ .tIR_min = 0,
+ .tITC_max = 1000000,
+ .tRC_min = 25000,
+ .tREA_max = 20000,
+ .tREH_min = 10000,
+ .tRHOH_min = 15000,
+ .tRHW_min = 100000,
+ .tRHZ_max = 100000,
+ .tRLOH_min = 5000,
+ .tRP_min = 12000,
+ .tRR_min = 20000,
+ .tRST_max = 500000000,
+ .tWB_max = 100000,
+ .tWC_min = 25000,
+ .tWH_min = 10000,
+ .tWHR_min = 80000,
+ .tWP_min = 12000,
+ .tWW_min = 100000,
+ },
+ /* Mode 5 */
+ {
+ .tADL_min = 70000,
+ .tALH_min = 5000,
+ .tALS_min = 10000,
+ .tAR_min = 10000,
+ .tCEA_max = 25000,
+ .tCEH_min = 20000,
+ .tCH_min = 5000,
+ .tCHZ_max = 30000,
+ .tCLH_min = 5000,
+ .tCLR_min = 10000,
+ .tCLS_min = 10000,
+ .tCOH_min = 15000,
+ .tCS_min = 15000,
+ .tDH_min = 5000,
+ .tDS_min = 7000,
+ .tFEAT_max = 1000000,
+ .tIR_min = 0,
+ .tITC_max = 1000000,
+ .tRC_min = 20000,
+ .tREA_max = 16000,
+ .tREH_min = 7000,
+ .tRHOH_min = 15000,
+ .tRHW_min = 100000,
+ .tRHZ_max = 100000,
+ .tRLOH_min = 5000,
+ .tRP_min = 10000,
+ .tRR_min = 20000,
+ .tRST_max = 500000000,
+ .tWB_max = 100000,
+ .tWC_min = 20000,
+ .tWH_min = 7000,
+ .tWHR_min = 80000,
+ .tWP_min = 10000,
+ .tWW_min = 100000,
+ },
+};
+
+/**
+ * onfi_async_timing_mode_to_sdr_timings - [NAND Interface] Retrieve NAND
+ * timings according to the given ONFI timing mode
+ * @mode: ONFI timing mode
+ */
+const struct nand_sdr_timings *onfi_async_timing_mode_to_sdr_timings(int mode)
+{
+ if (mode < 0 || mode >= ARRAY_SIZE(onfi_sdr_timings))
+ return ERR_PTR(-EINVAL);
+
+ return &onfi_sdr_timings[mode];
+}
+EXPORT_SYMBOL(onfi_async_timing_mode_to_sdr_timings);
#define ifc_in32(a) in_le32(a)
#define ifc_out32(a, v) out_le32(a, v)
#define ifc_in16(a) in_le16(a)
+#define ifc_out16(a, v) out_le16(a, v)
#elif defined(CONFIG_SYS_FSL_IFC_BE)
#define ifc_in32(a) in_be32(a)
#define ifc_out32(a, v) out_be32(a, v)
#define ifc_in16(a) in_be16(a)
+#define ifc_out16(a, v) out_be16(a, v)
#else
#error Neither CONFIG_SYS_FSL_IFC_LE nor CONFIG_SYS_FSL_IFC_BE is defined
#endif
* be provided if an hardware ECC is available
* @calculate: function for ECC calculation or readback from ECC hardware
* @correct: function for ECC correction, matching to ECC generator (sw/hw)
- * @read_page_raw: function to read a raw page without ECC
- * @write_page_raw: function to write a raw page without ECC
+ * @read_page_raw: function to read a raw page without ECC. This function
+ * should hide the specific layout used by the ECC
+ * controller and always return contiguous in-band and
+ * out-of-band data even if they're not stored
+ * contiguously on the NAND chip (e.g.
+ * NAND_ECC_HW_SYNDROME interleaves in-band and
+ * out-of-band data).
+ * @write_page_raw: function to write a raw page without ECC. This function
+ * should hide the specific layout used by the ECC
+ * controller and consider the passed data as contiguous
+ * in-band and out-of-band data. ECC controller is
+ * responsible for doing the appropriate transformations
+ * to adapt to its specific layout (e.g.
+ * NAND_ECC_HW_SYNDROME interleaves in-band and
+ * out-of-band data).
* @read_page: function to read a page according to the ECC generator
* requirements; returns maximum number of bitflips corrected in
* any single ECC step, 0 if bitflips uncorrectable, -EIO hw error
* @ecc: [BOARDSPECIFIC] ECC control structure
* @buffers: buffer structure for read/write
* @hwcontrol: platform-specific hardware control structure
- * @erase_cmd: [INTERN] erase command write function, selectable due
- * to AND support.
+ * @erase: [REPLACEABLE] erase function
* @scan_bbt: [REPLACEABLE] function to scan bad block table
* @chip_delay: [BOARDSPECIFIC] chip dependent delay for transferring
* data from array to read regs (tR).
* @ecc_step_ds: [INTERN] ECC step required by the @ecc_strength_ds,
* also from the datasheet. It is the recommended ECC step
* size, if known; if unknown, set to zero.
+ * @onfi_timing_mode_default: [INTERN] default ONFI timing mode. This field is
+ * either deduced from the datasheet if the NAND
+ * chip is not ONFI compliant or set to 0 if it is
+ * (an ONFI chip is always configured in mode 0
+ * after a NAND reset)
* @numchips: [INTERN] number of physical chips
* @chipsize: [INTERN] the size of one chip for multichip arrays
* @pagemask: [INTERN] page number mask = number of (pages / chip) - 1
void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column,
int page_addr);
int(*waitfunc)(struct mtd_info *mtd, struct nand_chip *this);
- void (*erase_cmd)(struct mtd_info *mtd, int page);
+ int (*erase)(struct mtd_info *mtd, int page);
int (*scan_bbt)(struct mtd_info *mtd);
int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state,
int status, int page);
uint8_t bits_per_cell;
uint16_t ecc_strength_ds;
uint16_t ecc_step_ds;
+ int onfi_timing_mode_default;
int badblockpos;
int badblockbits;
#define NAND_MFR_EON 0x92
#define NAND_MFR_SANDISK 0x45
#define NAND_MFR_INTEL 0x89
+#define NAND_MFR_ATO 0x9b
/* The maximum expected count of bytes in the NAND ID sequence */
#define NAND_MAX_ID_LEN 8
* @options: stores various chip bit options
* @id_len: The valid length of the @id.
* @oobsize: OOB size
+ * @ecc: ECC correctability and step information from the datasheet.
* @ecc.strength_ds: The ECC correctability from the datasheet, same as the
* @ecc_strength_ds in nand_chip{}.
* @ecc.step_ds: The ECC step required by the @ecc.strength_ds, same as the
* @ecc_step_ds in nand_chip{}, also from the datasheet.
* For example, the "4bit ECC for each 512Byte" can be set with
* NAND_ECC_INFO(4, 512).
+ * @onfi_timing_mode_default: the default ONFI timing mode entered after a NAND
+ * reset. Should be deduced from timings described
+ * in the datasheet.
+ *
*/
struct nand_flash_dev {
char *name;
uint16_t strength_ds;
uint16_t step_ds;
} ecc;
+ int onfi_timing_mode_default;
};
/**
void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len);
void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len);
uint8_t nand_read_byte(struct mtd_info *mtd);
+
+/*
+ * struct nand_sdr_timings - SDR NAND chip timings
+ *
+ * This struct defines the timing requirements of a SDR NAND chip.
+ * These informations can be found in every NAND datasheets and the timings
+ * meaning are described in the ONFI specifications:
+ * www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf (chapter 4.15 Timing
+ * Parameters)
+ *
+ * All these timings are expressed in picoseconds.
+ */
+
+struct nand_sdr_timings {
+ u32 tALH_min;
+ u32 tADL_min;
+ u32 tALS_min;
+ u32 tAR_min;
+ u32 tCEA_max;
+ u32 tCEH_min;
+ u32 tCH_min;
+ u32 tCHZ_max;
+ u32 tCLH_min;
+ u32 tCLR_min;
+ u32 tCLS_min;
+ u32 tCOH_min;
+ u32 tCS_min;
+ u32 tDH_min;
+ u32 tDS_min;
+ u32 tFEAT_max;
+ u32 tIR_min;
+ u32 tITC_max;
+ u32 tRC_min;
+ u32 tREA_max;
+ u32 tREH_min;
+ u32 tRHOH_min;
+ u32 tRHW_min;
+ u32 tRHZ_max;
+ u32 tRLOH_min;
+ u32 tRP_min;
+ u32 tRR_min;
+ u64 tRST_max;
+ u32 tWB_max;
+ u32 tWC_min;
+ u32 tWH_min;
+ u32 tWHR_min;
+ u32 tWP_min;
+ u32 tWW_min;
+};
+
+/* get timing characteristics from ONFI timing mode. */
+const struct nand_sdr_timings *onfi_async_timing_mode_to_sdr_timings(int mode);
#endif /* __LINUX_MTD_NAND_H */
projects / karo-tx-uboot.git / commitdiff