/*
+ * (C) Copyright 2005-2008
+ * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
+ *
* (C) Copyright 2001-2004
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
*
/*
* board/config.h - configuration options, board specific
*/
-
#ifndef __CONFIG_H
#define __CONFIG_H
* High Level Configuration Options
* (easy to change)
*/
-
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_APCG405 1 /* ...on a APC405 board */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
+#define CONFIG_BOARD_EARLY_INIT_R 1
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
#define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */
#define CONFIG_BOARD_TYPES 1 /* support board types */
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_BOOTDELAY 1 /* autoboot after 3 seconds */
#undef CONFIG_BOOTARGS
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "bootm ffc00000 ffca0000"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "bootm ffc00000"
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#define CFG_USB_LOAD_COMMAND "fatload usb 0 200000 pImage;" \
+ "fatload usb 0 300000 pImage.initrd"
+#define CFG_USB_SELF_COMMAND "usb start;run usb_load;usb stop;" \
+ "run ramargs addip addcon usbargs;" \
+ "bootm 200000 300000"
+#define CFG_USB_ARGS "setenv bootargs $(bootargs) usbboot=1"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hostname=abg405\0" \
+ "bd_type=abg405\0" \
+ "serial#=AA0000\0" \
+ "kernel_addr=fe000000\0" \
+ "ramdisk_addr=fe100000\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$(serverip):$(rootpath)\0" \
+ "addip=setenv bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
+ ":$(hostname)::off panic=1\0" \
+ "addcon=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)" \
+ " $(optargs)\0" \
+ "flash_self=run ramargs addip addcon;" \
+ "bootm $(kernel_addr) $(ramdisk_addr)\0" \
+ "net_nfs=tftp 200000 $(img);run nfsargs addip addcon;" \
+ "bootm\0" \
+ "rootpath=/tftpboot/abg405/target_root\0" \
+ "img=/tftpboot/abg405/pImage\0" \
+ "load=tftp 100000 /tftpboot/abg405/u-boot.bin\0" \
+ "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \
+ "cp.b 100000 fff80000 80000\0" \
+ "ipaddr=10.0.111.111\0" \
+ "netmask=255.255.0.0\0" \
+ "serverip=10.0.0.190\0" \
+ "splashimage=ffe80000\0" \
+ "usb_load="CFG_USB_LOAD_COMMAND"\0" \
+ "usb_self="CFG_USB_SELF_COMMAND"\0" \
+ "usbargs="CFG_USB_ARGS"\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run flash_self;run usb_self"
+
+#define CONFIG_ETHADDR 00:02:27:8e:00:00
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_NET_MULTI 1
+#undef CONFIG_HAS_ETH1
+
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1
+#define CONFIG_RESET_PHY_R 1 /* use reset_phy() */
#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
-
/*
* BOOTP options
*/
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-
/*
* Command line configuration.
*/
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_AUTOSCRIPT
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_SUPPORT_VFAT
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#define CONFIG_AUTO_UPDATE 1 /* autoupdate via CF or USB */
-#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
-#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
+#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
+
+#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-
-#undef CFG_HUSH_PARSER /* use "hush" command parser */
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
+#define CFG_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#if 1 /* test-only */
#define CFG_EXT_SERIAL_CLOCK 14745600 /* use external serial clock */
-#else
-#undef CFG_EXT_SERIAL_CLOCK /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
-#define CFG_BASE_BAUD 691200
-#endif
/* The following table includes the supported baudrates */
#define CFG_BAUDRATE_TABLE \
- { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
+ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
/* Only interrupt boot if space is pressed */
/* If a long serial cable is connected but */
/* other end is dead, garbage will be read */
-#define CONFIG_AUTOBOOT_KEYED 1
-#define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d seconds\n"
-#define CONFIG_AUTOBOOT_DELAY_STR "d"
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d seconds\n"
+#undef CONFIG_AUTOBOOT_DELAY_STR
#define CONFIG_AUTOBOOT_STOP_STR " "
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
-/*-----------------------------------------------------------------------
+/*
* PCI stuff
- *-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
/* resource configuration */
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-
-#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
-
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_SKIP_HOST_BRIDGE 1
#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
-/*-----------------------------------------------------------------------
+/*
* IDE/ATA stuff
- *-----------------------------------------------------------------------
*/
-#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#define CONFIG_IDE_RESET 1 /* reset for ide supported */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#define CONFIG_IDE_RESET 1 /* reset for ide supported */
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
-#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS) /* max. 1 drives per IDE bus */
-#define CFG_ATA_BASE_ADDR 0xF0100000
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_BASE_ADDR 0xF0100000
+#define CFG_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
-#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
+#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0000 /* Offset for normal register access */
+#define CFG_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
-/*-----------------------------------------------------------------------
+/*
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_MONITOR_BASE 0xFFF80000
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CFG_MALLOC_LEN (2*1024*1024) /* Reserve 2MB for malloc() */
+#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
+#define CFG_MALLOC_LEN (2*1024*1024) /* Reserve 2MB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Init. Memory map for Linux */
-/*-----------------------------------------------------------------------
+/*
* FLASH organization
*/
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#undef CFG_FLASH_PROTECTION /* don't use hardware protection */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_BASE 0xFE000000 /* test-only...*/
-#define CFG_FLASH_INCREMENT 0x01000000 /* test-only */
-
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#ifndef __ASSEMBLY__
+extern int flash_banks;
+#endif
-#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains u-boot */
+#define CFG_FLASH_BASE 0xFE000000
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */
+#define CFG_MAX_FLASH_BANKS flash_banks /* max num of flash banks */
+ /* updated in board_early_init_r */
+#define CFG_MAX_FLASH_BANKS_DETECT 2
+#define CFG_FLASH_QUIET_TEST 1
+#define CFG_FLASH_INCREMENT 0x01000000
+#define CFG_FLASH_PROTECTION 1 /* use hardware protection */
+#define CFG_FLASH_AUTOPROTECT_LIST { \
+ {0xfe000000, 0x500000}, \
+ {0xffe80000, 0x180000} \
+ }
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CFG_FLASH_BANKS_LIST { \
+ CFG_FLASH_BASE, \
+ CFG_FLASH_BASE + CFG_FLASH_INCREMENT \
+ }
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-/*-----------------------------------------------------------------------
+/*
* Environment Variable setup
*/
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
- /* total size of a CAT24WC16 is 2048 bytes */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the */
+ /* beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/
+#define CONFIG_ENV_OVERWRITE 1 /* allow overwriting vendor vars */
-#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
-#define CFG_NVRAM_SIZE 242 /* NVRAM size */
+#define CFG_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */
+#define CFG_NVRAM_SIZE 242 /* NVRAM size */
-/*-----------------------------------------------------------------------
+/*
* I2C EEPROM (CAT24WC16) for environment
*/
#define CONFIG_HARD_I2C /* I2c with hardware support */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
-#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
+#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+/* mask of address bits that overflow into the "EEPROM chip address" */
#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
+#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
- /* last 4 bits of the address */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+ /* last 4 bits of the address */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
#define CFG_EEPROM_PAGE_WRITE_ENABLE
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */
- /* have only 8kB, 16kB is save here */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
+/*
* External Bus Controller (EBC) Setup
*/
-#define FLASH0_BA 0xFF000000 /* FLASH 0 Base Address */
-#define FLASH1_BA 0xFE000000 /* FLASH 1 Base Address */
-#define CAN_BA 0xF0000000 /* CAN Base Address */
-#define DUART0_BA 0xF0000400 /* DUART Base Address */
-#define DUART1_BA 0xF0000408 /* DUART Base Address */
-#define RTC_BA 0xF0000500 /* RTC Base Address */
-#define PS2_BA 0xF0000600 /* PS/2 Base Address */
-#define CF_BA 0xF0100000 /* CompactFlash Base Address */
-#define FPGA_BA 0xF0100100 /* FPGA internal Base Address */
-#define FUJI_BA 0xF0100200 /* Fuji internal Base Address */
-#define PCMCIA1_BA 0x20000000 /* PCMCIA Slot 1 Base Address */
-#define PCMCIA2_BA 0x28000000 /* PCMCIA Slot 2 Base Address */
-#define VGA_BA 0xF1000000 /* Epson VGA Base Address */
-
-#define CFG_FPGA_BASE_ADDR FPGA_BA /* FPGA internal Base Address */
-
-/* Memory Bank 0 (Flash Bank 0) initialization */
+#define FLASH0_BA (CFG_FLASH_BASE + CFG_FLASH_INCREMENT) /* FLASH 0 BA */
+#define FLASH1_BA CFG_FLASH_BASE /* FLASH 1 Base Address */
+#define CAN_BA 0xF0000000 /* CAN Base Address */
+#define DUART0_BA 0xF0000400 /* DUART Base Address */
+#define DUART1_BA 0xF0000408 /* DUART Base Address */
+#define RTC_BA 0xF0000500 /* RTC Base Address */
+#define PS2_BA 0xF0000600 /* PS/2 Base Address */
+#define CF_BA 0xF0100000 /* CompactFlash Base Address */
+#define FPGA_BA 0xF0100100 /* FPGA internal Base Address */
+#define FUJI_BA 0xF0100200 /* Fuji internal Base Address */
+#define PCMCIA1_BA 0x20000000 /* PCMCIA Slot 1 Base Address */
+#define PCMCIA2_BA 0x28000000 /* PCMCIA Slot 2 Base Address */
+#define VGA_BA 0xF1000000 /* Epson VGA Base Address */
+
+#define CFG_FPGA_BASE_ADDR FPGA_BA /* FPGA internal Base Address */
+
+/* Memory Bank 0 (Flash Bank 0) initialization */
#define CFG_EBC_PB0AP 0x92015480
#define CFG_EBC_PB0CR FLASH0_BA | 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/
+#define CFG_EBC_PB0AP_HWREV8 CFG_EBC_PB0AP
+#define CFG_EBC_PB0CR_HWREV8 FLASH1_BA | 0xBA000 /* BS=32MB */
-/* Memory Bank 1 (Flash Bank 1) initialization */
+/* Memory Bank 1 (Flash Bank 1) initialization */
#define CFG_EBC_PB1AP 0x92015480
#define CFG_EBC_PB1CR FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/
#define CFG_EBC_PB6AP 0x050007C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CFG_EBC_PB6CR PCMCIA2_BA | 0xFA000 /*BAS=0x280,BS=128MB,BU=R/W,BW=16bit*/
-/*-----------------------------------------------------------------------
+/*
* FPGA stuff
*/
#define CFG_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
#define CFG_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
-/*-----------------------------------------------------------------------
+/*
* LCD Setup
*/
+#define CFG_LCD_BIG_MEM (VGA_BA + 0x200000) /* S1D13806 Mem Base */
+#define CFG_LCD_BIG_REG VGA_BA /* S1D13806 Reg Base */
-#define CFG_LCD_BIG_MEM 0xF1200000 /* Epson S1D13806 Mem Base Address */
-#define CFG_LCD_BIG_REG 0xF1000000 /* Epson S1D13806 Reg Base Address */
-
-#define CONFIG_LCD_BIG 2 /* Epson S1D13806 used */
+#define CONFIG_LCD_BIG 2 /* Epson S1D13806 used */
/* Image information... */
-#define CONFIG_LCD_USED CONFIG_LCD_BIG
-#define CFG_LCD_HEADER_NAME "../common/s1d13806_640_480_16bpp.h"
-#define CFG_LCD_LOGO_NAME "logo_640_480_24bpp.c"
+#define CONFIG_LCD_USED CONFIG_LCD_BIG
-#define CFG_LCD_MEM CFG_LCD_BIG_MEM
-#define CFG_LCD_REG CFG_LCD_BIG_REG
+#define CFG_LCD_MEM CFG_LCD_BIG_MEM
+#define CFG_LCD_REG CFG_LCD_BIG_REG
#define CFG_VIDEO_LOGO_MAX_SIZE (1 << 20)
-/*-----------------------------------------------------------------------
+/*
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM 1
+#define CFG_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CFG_OCM_DATA_ADDR 0xF8000000
#define CFG_OCM_DATA_SIZE 0x1000
-#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
-#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */
+#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE 128 /* reserved bytes for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
* Internal Definitions
*
* Boot Flags
*/
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#endif /* __CONFIG_H */
+/*
+ * PCI OHCI controller
+ */
+#define CONFIG_USB_OHCI_NEW 1
+#define CONFIG_PCI_OHCI 1
+#define CFG_OHCI_SWAP_REG_ACCESS 1
+#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+#define CFG_USB_OHCI_SLOT_NAME "ohci_pci"
+#define CONFIG_USB_STORAGE 1
+#define CFG_USB_OHCI_BOARD_INIT 1
+
+#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / commitdiff