This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
#if defined(CONFIG_8xx)
#define _machine _MACH_8xx
#define have_of 0
-#elif defined(CONFIG_OAK)
-#define _machine _MACH_oak
-#define have_of 0
#elif defined(CONFIG_WALNUT)
#define _machine _MACH_walnut
#define have_of 0
-#elif defined(CONFIG_APUS)
-#define _machine _MACH_apus
-#define have_of 0
-#elif defined(CONFIG_GEMINI)
-#define _machine _MACH_gemini
-#define have_of 0
#elif defined(CONFIG_MPC8260)
#define _machine _MACH_8260
#define have_of 0
#elif defined(CONFIG_SANDPOINT)
#define _machine _MACH_sandpoint
-#elif defined(CONFIG_HIDDEN_DRAGON)
-#define _machine _MACH_hidden_dragon
-#define have_of 0
#else
#error "Machine not defined correctly"
#endif
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = hidden_dragon.o flash.o
+++ /dev/null
-U-Boot for Hidden Dragon board
-------------------------------
-
-Hidden Dragon is a MPC824x-based board by Motorola. For the most
-part it is similar to Sandpoint8245 board. So unless otherwise
-mentioned, the codes in this directory are adapted from ../sandpoint
-directory.
-
-Apparently there are very few of this board out there. Even Motorola
-website does not have any info on it.
-
-RAM:
- start = 0x0000 0000
- size = 0x0200 0000 (32 MB)
-
-Flash:
- BANK ONE:
- start = 0xFFE0 0000
- size = 0x0020 0000 (2 MB)
- flash chip = 29LV160TE (1x16 Mbits or 2x8 Mbits)
- flash sectors = 16K, 2x8K, 32K, 31x64K
-
- BANK TWO:
- NONE
-
-The processor interrupt vectors reside on the first 256 bytes
-starting from address 0xFFF00000. The "reset vector" (first
-instruction executed after reset) is located on 0xFFF0 0100.
-
-U-Boot is configured to reside in flash starting at the address of
-0xFFF00000. The environment space is located in flash separately from
-U-Boot, at the second sector of the first flash bank, starting from
-0xFFE04000 until 0xFFE06000 (8KB).
-
-Network:
- - RTL8139 chip on the base board (SUPPORTED)
- - RTL8129 chip on the processor board (NOT SUPPORTED)
-
-Serial:
- - Two NS16550 compatible UART on the processor board (SUPPORTED)
- - One NS16550 compatible UART on the base board (UNTESTED)
-
-Misc:
- VIA686A PCI SuperIO peripheral controller
- - 2 USB ports (UNTESTED)
- - 2 PS2 ports (UNTESTED)
- - Parallel port (UNTESTED)
- - IDE & floppy interface (UNTESTED)
-
- S3 Savage4 video card (UNTESTED)
-
-TODO:
------
-- Support for the VIA686A based peripherals
-- The RTL8139 driver frequently gives rx error.
-- Support for RTL8129 network controller. (Why is the support removed from
- rtl8139.c driver?)
-
-(C) Copyright 2004
-Yusdi Santoso, Adaptec Inc., yusdi_santoso@adaptec.com
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Yusdi Santoso, Adaptec Inc., yusdi_santoso@adaptec.com
- *
- * (C) Copyright 2000-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <asm/processor.h>
-#include <asm/pci_io.h>
-#include <w83c553f.h>
-
-#define ROM_CS0_START 0xFF800000
-#define ROM_CS1_START 0xFF000000
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-
-/*flash command address offsets*/
-
-#define ADDR0 (0xAAA)
-#define ADDR1 (0x555)
-#define ADDR3 (0x001)
-
-#define FLASH_WORD_SIZE unsigned char
-
-/*-----------------------------------------------------------------------
- */
-
-static unsigned long flash_id (unsigned char mfct, unsigned char chip)
- __attribute__ ((const));
-
-typedef struct {
- FLASH_WORD_SIZE extval;
- unsigned short intval;
-} map_entry;
-
-static unsigned long flash_id (unsigned char mfct, unsigned char chip)
-{
- static const map_entry mfct_map[] = {
- {(FLASH_WORD_SIZE) AMD_MANUFACT,
- (unsigned short) ((unsigned long) FLASH_MAN_AMD >> 16)},
- {(FLASH_WORD_SIZE) FUJ_MANUFACT,
- (unsigned short) ((unsigned long) FLASH_MAN_FUJ >> 16)},
- {(FLASH_WORD_SIZE) STM_MANUFACT,
- (unsigned short) ((unsigned long) FLASH_MAN_STM >> 16)},
- {(FLASH_WORD_SIZE) MT_MANUFACT,
- (unsigned short) ((unsigned long) FLASH_MAN_MT >> 16)},
- {(FLASH_WORD_SIZE) INTEL_MANUFACT,
- (unsigned short) ((unsigned long) FLASH_MAN_INTEL >> 16)},
- {(FLASH_WORD_SIZE) INTEL_ALT_MANU,
- (unsigned short) ((unsigned long) FLASH_MAN_INTEL >> 16)}
- };
-
- static const map_entry chip_map[] = {
- {AMD_ID_F040B, FLASH_AM040},
- {(FLASH_WORD_SIZE) STM_ID_x800AB, FLASH_STM800AB}
- };
-
- const map_entry *p;
- unsigned long result = FLASH_UNKNOWN;
-
- /* find chip id */
- for (p = &chip_map[0];
- p < &chip_map[sizeof chip_map / sizeof chip_map[0]]; p++)
- if (p->extval == chip) {
- result = FLASH_VENDMASK | p->intval;
- break;
- }
-
- /* find vendor id */
- for (p = &mfct_map[0];
- p < &mfct_map[sizeof mfct_map / sizeof mfct_map[0]]; p++)
- if (p->extval == mfct) {
- result &= ~FLASH_VENDMASK;
- result |= (unsigned long) p->intval << 16;
- break;
- }
-
- return result;
-}
-
-unsigned long flash_init (void)
-{
- unsigned long i;
- unsigned char j;
- static const ulong flash_banks[] = CONFIG_SYS_FLASH_BANKS;
-
- /* Init: no FLASHes known */
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
- flash_info_t *const pflinfo = &flash_info[i];
-
- pflinfo->flash_id = FLASH_UNKNOWN;
- pflinfo->size = 0;
- pflinfo->sector_count = 0;
- }
-
- /* Enable writes to Hidden Dragon flash */
- {
- register unsigned char temp;
-
- CONFIG_READ_BYTE (CONFIG_SYS_WINBOND_ISA_CFG_ADDR + WINBOND_CSCR,
- temp);
- temp &= ~0x20; /* clear BIOSWP bit */
- CONFIG_WRITE_BYTE (CONFIG_SYS_WINBOND_ISA_CFG_ADDR + WINBOND_CSCR,
- temp);
- }
-
- for (i = 0; i < sizeof flash_banks / sizeof flash_banks[0]; i++) {
- flash_info_t *const pflinfo = &flash_info[i];
- const unsigned long base_address = flash_banks[i];
- volatile FLASH_WORD_SIZE *const flash =
- (FLASH_WORD_SIZE *) base_address;
-
- flash[0xAAA << (3 * i)] = 0xaa;
- flash[0x555 << (3 * i)] = 0x55;
- flash[0xAAA << (3 * i)] = 0x90;
- __asm__ __volatile__ ("sync");
-
- pflinfo->flash_id =
- flash_id (flash[0x0], flash[0x2 + 14 * i]);
-
- switch (pflinfo->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM040:
- pflinfo->size = 0x00080000;
- pflinfo->sector_count = 8;
- for (j = 0; j < 8; j++) {
- pflinfo->start[j] =
- base_address + 0x00010000 * j;
- pflinfo->protect[j] = flash[(j << 16) | 0x2];
- }
- break;
- case FLASH_STM800AB:
- pflinfo->size = 0x00100000;
- pflinfo->sector_count = 19;
- pflinfo->start[0] = base_address;
- pflinfo->start[1] = base_address + 0x4000;
- pflinfo->start[2] = base_address + 0x6000;
- pflinfo->start[3] = base_address + 0x8000;
- for (j = 1; j < 16; j++) {
- pflinfo->start[j + 3] =
- base_address + 0x00010000 * j;
- }
- break;
- default:
- /* The chip used is not listed in flash_id
- TODO: Change this to explicitly detect the flash type
- */
- {
- int sector_addr = base_address;
-
- pflinfo->size = 0x00200000;
- pflinfo->sector_count = 35;
- pflinfo->start[0] = sector_addr;
- sector_addr += 0x4000; /* 16K */
- pflinfo->start[1] = sector_addr;
- sector_addr += 0x2000; /* 8K */
- pflinfo->start[2] = sector_addr;
- sector_addr += 0x2000; /* 8K */
- pflinfo->start[3] = sector_addr;
- sector_addr += 0x8000; /* 32K */
-
- for (j = 4; j < 35; j++) {
- pflinfo->start[j] = sector_addr;
- sector_addr += 0x10000; /* 64K */
- }
- }
- break;
- }
- /* Protect monitor and environment sectors
- */
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[0]);
-#endif
-
-#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR)
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1,
- &flash_info[0]);
-#endif
-
- /* reset device to read mode */
- flash[0x0000] = 0xf0;
- __asm__ __volatile__ ("sync");
- }
-
- /* only have 1 bank */
- return flash_info[0].size;
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- static const char unk[] = "Unknown";
- const char *mfct = unk, *type = unk;
- unsigned int i;
-
- if (info->flash_id != FLASH_UNKNOWN) {
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD:
- mfct = "AMD";
- break;
- case FLASH_MAN_FUJ:
- mfct = "FUJITSU";
- break;
- case FLASH_MAN_STM:
- mfct = "STM";
- break;
- case FLASH_MAN_SST:
- mfct = "SST";
- break;
- case FLASH_MAN_BM:
- mfct = "Bright Microelectonics";
- break;
- case FLASH_MAN_INTEL:
- mfct = "Intel";
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_AM040:
- type = "AM29F040B (512K * 8, uniform sector size)";
- break;
- case FLASH_AM400B:
- type = "AM29LV400B (4 Mbit, bottom boot sect)";
- break;
- case FLASH_AM400T:
- type = "AM29LV400T (4 Mbit, top boot sector)";
- break;
- case FLASH_AM800B:
- type = "AM29LV800B (8 Mbit, bottom boot sect)";
- break;
- case FLASH_AM800T:
- type = "AM29LV800T (8 Mbit, top boot sector)";
- break;
- case FLASH_AM160T:
- type = "AM29LV160T (16 Mbit, top boot sector)";
- break;
- case FLASH_AM320B:
- type = "AM29LV320B (32 Mbit, bottom boot sect)";
- break;
- case FLASH_AM320T:
- type = "AM29LV320T (32 Mbit, top boot sector)";
- break;
- case FLASH_STM800AB:
- type = "M29W800AB (8 Mbit, bottom boot sect)";
- break;
- case FLASH_SST800A:
- type = "SST39LF/VF800 (8 Mbit, uniform sector size)";
- break;
- case FLASH_SST160A:
- type = "SST39LF/VF160 (16 Mbit, uniform sector size)";
- break;
- }
- }
-
- printf ("\n Brand: %s Type: %s\n"
- " Size: %lu KB in %d Sectors\n",
- mfct, type, info->size >> 10, info->sector_count);
-
- printf (" Sector Start Addresses:");
-
- for (i = 0; i < info->sector_count; i++) {
- unsigned long size;
- unsigned int erased;
- unsigned long *flash = (unsigned long *) info->start[i];
-
- /*
- * Check if whole sector is erased
- */
- size = (i != (info->sector_count - 1)) ?
- (info->start[i + 1] - info->start[i]) >> 2 :
- (info->start[0] + info->size - info->start[i]) >> 2;
-
- for (flash = (unsigned long *) info->start[i], erased = 1;
- (flash != (unsigned long *) info->start[i] + size)
- && erased; flash++)
- erased = *flash == ~0x0UL;
-
- printf ("%s %08lX %s %s",
- (i % 5) ? "" : "\n ",
- info->start[i],
- erased ? "E" : " ", info->protect[i] ? "RO" : " ");
- }
-
- puts ("\n");
- return;
-}
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *) (info->start[0]);
- int flag, prot, sect, l_sect;
- ulong start, now, last;
- unsigned char sh8b;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id == FLASH_UNKNOWN) ||
- (info->flash_id > (FLASH_MAN_STM | FLASH_AMD_COMP))) {
- printf ("Can't erase unknown flash type - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n", prot);
- } else {
- printf ("\n");
- }
-
- l_sect = -1;
-
- /* Check the ROM CS */
- if ((info->start[0] >= ROM_CS1_START)
- && (info->start[0] < ROM_CS0_START))
- sh8b = 3;
- else
- sh8b = 0;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00AA00AA;
- addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE) 0x00550055;
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00800080;
- addr[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00AA00AA;
- addr[ADDR1 << sh8b] = (FLASH_WORD_SIZE) 0x00550055;
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (FLASH_WORD_SIZE *) (info->start[0] +
- ((info->start[sect] -
- info->start[0]) << sh8b));
- if (info->flash_id & FLASH_MAN_SST) {
- addr[ADDR0 << sh8b] =
- (FLASH_WORD_SIZE) 0x00AA00AA;
- addr[ADDR1 << sh8b] =
- (FLASH_WORD_SIZE) 0x00550055;
- addr[ADDR0 << sh8b] =
- (FLASH_WORD_SIZE) 0x00800080;
- addr[ADDR0 << sh8b] =
- (FLASH_WORD_SIZE) 0x00AA00AA;
- addr[ADDR1 << sh8b] =
- (FLASH_WORD_SIZE) 0x00550055;
- addr[0] = (FLASH_WORD_SIZE) 0x00500050; /* block erase */
- udelay (30000); /* wait 30 ms */
- } else
- addr[0] = (FLASH_WORD_SIZE) 0x00300030; /* sector erase */
- l_sect = sect;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts ();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto DONE;
-
- start = get_timer (0);
- last = start;
- addr = (FLASH_WORD_SIZE *) (info->start[0] + ((info->start[l_sect] -
- info->
- start[0]) << sh8b));
- while ((addr[0] & (FLASH_WORD_SIZE) 0x00800080) !=
- (FLASH_WORD_SIZE) 0x00800080) {
- if ((now = get_timer (start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- serial_putc ('.');
- last = now;
- }
- }
-
- DONE:
- /* reset to read mode */
- addr = (FLASH_WORD_SIZE *) info->start[0];
- addr[0] = (FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */
-
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- for (; i < 4 && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < 4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- if ((rc = write_word (info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i = 0; i < 4; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word (info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < 4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- return (write_word (info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t * info, ulong dest, ulong data)
-{
- volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *) info->start[0];
- volatile FLASH_WORD_SIZE *dest2;
- volatile FLASH_WORD_SIZE *data2 = (FLASH_WORD_SIZE *) & data;
- ulong start;
- int flag;
- int i;
- unsigned char sh8b;
-
- /* Check the ROM CS */
- if ((info->start[0] >= ROM_CS1_START)
- && (info->start[0] < ROM_CS0_START))
- sh8b = 3;
- else
- sh8b = 0;
-
- dest2 = (FLASH_WORD_SIZE *) (((dest - info->start[0]) << sh8b) +
- info->start[0]);
-
- /* Check if Flash is (sufficiently) erased */
- if ((*dest2 & (FLASH_WORD_SIZE) data) != (FLASH_WORD_SIZE) data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- for (i = 0; i < 4 / sizeof (FLASH_WORD_SIZE); i++) {
- addr2[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00AA00AA;
- addr2[ADDR1 << sh8b] = (FLASH_WORD_SIZE) 0x00550055;
- addr2[ADDR0 << sh8b] = (FLASH_WORD_SIZE) 0x00A000A0;
-
- dest2[i << sh8b] = data2[i];
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts ();
-
- /* data polling for D7 */
- start = get_timer (0);
- while ((dest2[i << sh8b] & (FLASH_WORD_SIZE) 0x00800080) !=
- (data2[i] & (FLASH_WORD_SIZE) 0x00800080)) {
- if (get_timer (start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- return (1);
- }
- }
- }
-
- return (0);
-}
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Yusdi Santoso, Adaptec Inc., yusdi_santoso@adaptec.com
- *
- * (C) Copyright 2000
- * Rob Taylor, Flying Pig Systems. robt@flyingpig.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc824x.h>
-#include <pci.h>
-#include <netdev.h>
-
-int checkboard (void)
-{
- /*TODO: Check processor type */
-
- puts ( "Board: Hidden Dragon "
-#ifdef CONFIG_MPC8240
- "8240"
-#endif
-#ifdef CONFIG_MPC8245
- "8245"
-#endif
- " ##Test not implemented yet##\n");
- /* TODO: Implement board test */
- return 0;
-}
-
-phys_size_t initdram (int board_type)
-{
- long size;
- long new_bank0_end;
- long mear1;
- long emear1;
-
- size = get_ram_size(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MAX_RAM_SIZE);
-
- new_bank0_end = size - 1;
- mear1 = mpc824x_mpc107_getreg(MEAR1);
- emear1 = mpc824x_mpc107_getreg(EMEAR1);
- mear1 = (mear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
- emear1 = (emear1 & 0xFFFFFF00) |
- ((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
- mpc824x_mpc107_setreg(MEAR1, mear1);
- mpc824x_mpc107_setreg(EMEAR1, emear1);
-
- return (size);
-}
-
-/*
- * Initialize PCI Devices, report devices found.
- */
-#ifndef CONFIG_PCI_PNP
-static struct pci_config_table pci_hidden_dragon_config_table[] = {
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0f, PCI_ANY_ID,
- pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x10, PCI_ANY_ID,
- pci_cfgfunc_config_device, { PCI_ENET1_IOADDR,
- PCI_ENET1_MEMADDR,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
- { }
-};
-#endif
-
-struct pci_controller hose = {
-#ifndef CONFIG_PCI_PNP
- config_table: pci_hidden_dragon_config_table,
-#endif
-};
-
-void pci_init_board(void)
-{
- pci_mpc824x_init(&hose);
-}
-
-int board_eth_init(bd_t *bis)
-{
- return pci_eth_init(bis);
-}
Orphan blackfin blackfin - - - tcm-bf537 - Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
Orphan powerpc mpc5xxx - matrix_vision mvbc_p MVBC_P MVBC_P:MVBC_P Andre Schwarz <andre.schwarz@matrix-vision.de>
Orphan powerpc mpc5xxx - matrix_vision mvsmr MVSMR - Andre Schwarz <andre.schwarz@matrix-vision.de>
-Orphan powerpc mpc824x - - hidden_dragon HIDDEN_DRAGON - Yusdi Santoso <yusdi_santoso@adaptec.com>
Orphan powerpc mpc83xx - freescale mpc8360erdk MPC8360ERDK - Anton Vorontsov <avorontsov@ru.mvista.com>
Orphan powerpc mpc83xx - freescale mpc8360erdk MPC8360ERDK_33 MPC8360ERDK:CLKIN_33MHZ Anton Vorontsov <avorontsov@ru.mvista.com>
Orphan powerpc mpc83xx - matrix_vision mergerbox MERGERBOX - Andre Schwarz <andre.schwarz@matrix-vision.de>
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+hidden_dragon powerpc mpc824x - - Yusdi Santoso <yusdi_santoso@adaptec.com>
debris powerpc mpc824x - - Sangmoon Kim <dogoil@etinsys.com>
kvme080 powerpc mpc824x - - Sangmoon Kim <dogoil@etinsys.com>
ep8248 powerpc mpc8260 - - Yuli Barcohen <yuli@arabellasw.com>
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Yusdi Santoso, Adaptec Inc., yusdi_santoso@adaptec.com
- *
- * (C) Copyright 2001, 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8245 1
-#define CONFIG_HIDDEN_DRAGON 1
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-
-#if 0
-#define USE_DINK32 1
-#else
-#undef USE_DINK32
-#endif
-
-#define CONFIG_CONS_INDEX 3 /* set to '3' for on-chip DUART */
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_DRAM_SPEED 100 /* MHz */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#undef CONFIG_PCI_PNP
-
-
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-
-#define PCI_ENET0_IOADDR 0x80000000
-#define PCI_ENET0_MEMADDR 0x80000000
-#define PCI_ENET1_IOADDR 0x81000000
-#define PCI_ENET1_MEMADDR 0x81000000
-
-#define CONFIG_RTL8139
-
-/* Make sure the ethaddr can be overwritten
- TODO: Remove this on final product
-*/
-#define CONFIG_ENV_OVERWRITE
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE 0x02000000
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-
-#if defined (USE_DINK32)
-#define CONFIG_SYS_MONITOR_LEN 0x00030000
-#define CONFIG_SYS_MONITOR_BASE 0x00090000
-#define CONFIG_SYS_RAMBOOT 1
-#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_SYS_INIT_RAM_SIZE 0x10000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#else
-#undef CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_MONITOR_LEN 0x00030000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-#endif
-
-#define CONFIG_SYS_FLASH_BASE 0xFFE00000
-#define CONFIG_SYS_FLASH_SIZE (2 * 1024 * 1024) /* Unity has onboard 1MByte flash */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x00004000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */
-
-#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */
-
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */
-
-#define CONFIG_SYS_EUMB_ADDR 0xFC000000
-
-#define CONFIG_SYS_ISA_MEM 0xFD000000
-#define CONFIG_SYS_ISA_IO 0xFE000000
-
-#define CONFIG_SYS_FLASH_RANGE_BASE 0xFFE00000 /* flash memory address range */
-#define CONFIG_SYS_FLASH_RANGE_SIZE 0x00200000
-#define FLASH_BASE0_PRELIM 0xFFE00000 /* processor board flash */
-
-/*
- * select i2c support configuration
- *
- * Supported configurations are {none, software, hardware} drivers.
- * If the software driver is chosen, there are some additional
- * configuration items that the driver uses to drive the port pins.
- */
-#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-#ifdef CONFIG_SYS_I2C_SOFT
-#error "Soft I2C is not configured properly. Please review!"
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT_SPEED 50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE (iop->pdir |= 0x00010000)
-#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
-#define I2C_READ ((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
- else iop->pdat &= ~0x00010000
-#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
- else iop->pdat &= ~0x00020000
-#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-#endif /* CONFIG_SYS_I2C_SOFT */
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-
-#define CONFIG_SYS_FLASH_BANKS { FLASH_BASE0_PRELIM }
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-
-
-/* #define CONFIG_WINBOND_83C553 1 / *has a winbond bridge */
-#define CONFIG_SYS_USE_WINBOND_IDE 0 /*use winbond 83c553 internal IDE ctrlr */
-#define CONFIG_SYS_WINBOND_ISA_CFG_ADDR 0x80005800 /*pci-isa bridge config addr */
-#define CONFIG_SYS_WINBOND_IDE_CFG_ADDR 0x80005900 /*ide config addr */
-
-#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-
-/* TODO: Change this to VIA686A */
-
-/*
- * NS87308 Configuration
- */
-#define CONFIG_NS87308 /* Nat Semi super-io controller on ISA bus */
-
-#define CONFIG_SYS_NS87308_BADDR_10 1
-
-#define CONFIG_SYS_NS87308_DEVS ( CONFIG_SYS_NS87308_UART1 | \
- CONFIG_SYS_NS87308_UART2 | \
- CONFIG_SYS_NS87308_POWRMAN | \
- CONFIG_SYS_NS87308_RTC_APC )
-
-#undef CONFIG_SYS_NS87308_PS2MOD
-
-#define CONFIG_SYS_NS87308_CS0_BASE 0x0076
-#define CONFIG_SYS_NS87308_CS0_CONF 0x30
-#define CONFIG_SYS_NS87308_CS1_BASE 0x0075
-#define CONFIG_SYS_NS87308_CS1_CONF 0x30
-#define CONFIG_SYS_NS87308_CS2_BASE 0x0074
-#define CONFIG_SYS_NS87308_CS2_CONF 0x30
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-#if (CONFIG_CONS_INDEX > 2)
-#define CONFIG_SYS_NS16550_CLK CONFIG_DRAM_SPEED*1000000
-#else
-#define CONFIG_SYS_NS16550_CLK 1843200
-#endif
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART1_BASE)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART2_BASE)
-#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_EUMB_ADDR + 0x4500)
-#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_EUMB_ADDR + 0x4600)
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
-
-#define CONFIG_SYS_ROMNAL 7 /*rom/flash next access time */
-#define CONFIG_SYS_ROMFAL 11 /*rom/flash access time */
-
-#define CONFIG_SYS_REFINT 430 /* no of clock cycles between CBR refresh cycles */
-
-/* the following are for SDRAM only*/
-#define CONFIG_SYS_BSTOPRE 121 /* Burst To Precharge, sets open page interval */
-#define CONFIG_SYS_REFREC 8 /* Refresh to activate interval */
-#define CONFIG_SYS_RDLAT 4 /* data latency from read command */
-#define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval */
-#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */
-#define CONFIG_SYS_ACTORW 3 /* Activate to R/W */
-#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */
-#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */
-#if 0
-#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* OBSOLETE! SDMODE Burst length 2=4, 3=8 */
-#endif
-
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
-#define CONFIG_SYS_EXTROM 1
-#define CONFIG_SYS_REGDIMM 0
-
-
-/* memory bank settings*/
-/*
- * only bits 20-29 are actually used from these vales to set the
- * start/end address the upper two bits will be 0, and the lower 20
- * bits will be set to 0x00000 for a start address, or 0xfffff for an
- * end address
- */
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START 0x3ff00000
-#define CONFIG_SYS_BANK1_END 0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE 0
-#define CONFIG_SYS_BANK2_START 0x3ff00000
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x00000000
-#define CONFIG_SYS_BANK4_END 0x00000000
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x00000000
-#define CONFIG_SYS_BANK5_END 0x00000000
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x00000000
-#define CONFIG_SYS_BANK6_END 0x00000000
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x00000000
-#define CONFIG_SYS_BANK7_END 0x00000000
-#define CONFIG_SYS_BANK7_ENABLE 0
-/*
- * Memory bank enable bitmask, specifying which of the banks defined above
- are actually present. MSB is for bank #7, LSB is for bank #0.
- */
-#define CONFIG_SYS_BANK_ENABLE 0x01
-
-#define CONFIG_SYS_ODCR 0xff /* configures line driver impedances, */
- /* see 8240 book for bit definitions */
-#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 retains the */
- /* currently accessed page in memory */
- /* see 8240 book for details */
-
-/* SDRAM 0 - 256MB */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* stack in DCACHE @ 1GB (no backing mem) */
-#if defined(USE_DINK32)
-#define CONFIG_SYS_IBAT1L (0x40000000 | BATL_PP_00 )
-#define CONFIG_SYS_IBAT1U (0x40000000 | BATU_BL_128K )
-#else
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#endif
-
-/* PCI memory */
-#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* Flash, config addrs, etc */
-#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 36 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8240 CPU */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/* values according to the manual */
-#define CONFIG_DRAM_50MHZ 1
-#define CONFIG_SDRAM_50MHZ
-
-#undef NR_8259_INTS
-#define NR_8259_INTS 1
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / commitdiff