Changes since for U-Boot 0.1.0:
======================================================================
+* Vince Husovsky, 7 Nov 2002:
+ Add "-n" to linker options to get rid of "Not enough room for
+ program headers" problem
+
+* Patch by David Müller, 05 Nov 2002
+ Rename CONFIG_PLL_INPUT_FREQ to CONFIG_SYS_CLK_FREQ
+ so we can use an already existing name
+
+* Patch by Pierre Aubert, 05 Nov 2002
+ Hardware relatied improvments in FDC boot code
+
+* Patch by Holger Schurig, 5 Nov 2002:
+ Make the PXA really change it's frequency
+
+* Patch by Pierre Aubert, 05 Nov 2002
+ Add support for slave serial Spartan 2 FPGAs
+
+* Fix uninitialized memory (MAC address) in 8xx SCC/FEC ethernet
+ drivers
+
* Add support for log buffer which can be passed to Linux kernel's
syslog mechanism; used especially for POST results.
"include/configs/TQM823L.h".
+Many of the options are named exactly as the corresponding Linux
+kernel configuration options. The intention is to make it easier to
+build a config tool - later.
+
+
The following options need to be configured:
- CPU Type: Define exactly one of
configuration.
-Many of the options are named exactly as the corresponding Linux
-kernel configuration options. The intention is to make it easier to
-build a config tool - later.
-
Low Level (hardware related) configuration options:
- CFG_CACHELINE_SIZE:
to be able to adjust the position of the IMMR
register after a reset.
+- Floppy Disk Support:
+ CFG_FDC_DRIVE_NUMBER
+
+ the default drive number (default value 0)
+
+ CFG_ISA_IO_STRIDE
+
+ defines the spacing between fdc chipset registers
+ (default value 1)
+
+ CFG_ISA_IO_OFFSET
+
+ defines the offset of register from address. It
+ depends on which part of the data bus is connected to
+ the fdc chipset. (default value 0)
+
+ If CFG_ISA_IO_STRIDE CFG_ISA_IO_OFFSET and
+ CFG_FDC_DRIVE_NUMBER are undefined, they take their
+ default value.
+
+ if CFG_FDC_HW_INIT is defined, then the function
+ fdc_hw_init() is called at the beginning of the FDC
+ setup. fdc_hw_init() must be provided by the board
+ source code. It is used to make hardware dependant
+ initializations.
+
- CFG_IMMR: Physical address of the Internal Memory Mapped
Register; DO NOT CHANGE! (11-4)
[MPC8xx systems only]
static FDC_COMMAND_STRUCT cmd; /* global command struct */
+/* If the boot drive number is undefined, we assume it's drive 0 */
+#ifndef CFG_FDC_DRIVE_NUMBER
+#define CFG_FDC_DRIVE_NUMBER 0
+#endif
+
+/* Hardware access */
+#ifndef CFG_ISA_IO_STRIDE
+#define CFG_ISA_IO_STRIDE 1
+#endif
+
+#ifndef CFG_ISA_IO_OFFSET
+#define CFG_ISA_IO_OFFSET 0
+#endif
+
+
/* Supporting Functions */
/* reads a Register of the FDC */
unsigned char read_fdc_reg(unsigned int addr)
{
- volatile unsigned char *val = (volatile unsigned char *)(CFG_ISA_IO_BASE_ADDRESS | addr);
- return val[0];
+ volatile unsigned char *val = (volatile unsigned char *)(CFG_ISA_IO_BASE_ADDRESS + (addr * CFG_ISA_IO_STRIDE) + CFG_ISA_IO_OFFSET);
+
+ return val [0];
}
/* writes a Register of the FDC */
void write_fdc_reg(unsigned int addr, unsigned char val)
{
- volatile unsigned char *tmp = (volatile unsigned char *)(CFG_ISA_IO_BASE_ADDRESS | addr);
- tmp[0]=val;
+ volatile unsigned char *tmp = (volatile unsigned char *)(CFG_ISA_IO_BASE_ADDRESS + (addr * CFG_ISA_IO_STRIDE) + CFG_ISA_IO_OFFSET);
+ tmp[0]=val;
}
/* waits for an interrupt (polling) */
head = sect / pFG->sect; /* head nr */
sect = sect % pFG->sect; /* remaining blocks */
sect++; /* sectors are 1 based */
- PRINTF("Track %ld, Head %ld, Sector %ld, Drive %d (blnr %ld)\n",track,head,sect,pCMD->drive,pCMD->blnr);
+ PRINTF("Cmd 0x%02x Track %ld, Head %ld, Sector %ld, Drive %d (blnr %ld)\n",pCMD->cmd[0],track,head,sect,pCMD->drive,pCMD->blnr);
+
if(head|=0) { /* max heads = 2 */
pCMD->cmd[DRIVE]=pCMD->drive | 0x04; /* head 1 */
pCMD->cmd[HEAD]=(unsigned char) head; /* head register */
select_fdc_drive(pCMD);
pCMD->blnr=0; /* set to the 1st block */
if(fdc_recalibrate(pCMD,pFG)==FALSE)
- break;
+ continue;
if((pCMD->result[STATUS_0]&0x10)==0x10)
- break;
+ continue;
/* ok drive connected check for disk */
state|=(1<<drives);
pCMD->blnr=pFG->size; /* set to the last block */
if(fdc_seek(pCMD,pFG)==FALSE)
- break;
+ continue;
pCMD->blnr=0; /* set to the 1st block */
if(fdc_recalibrate(pCMD,pFG)==FALSE)
- break;
+ continue;
pCMD->cmd[COMMAND]=FDC_CMD_READ_ID;
if(fdc_issue_cmd(pCMD,pFG)==FALSE)
- break;
+ continue;
state|=(0x10<<drives);
}
stop_fdc_drive(pCMD);
{
int i;
+
+#ifdef CFG_FDC_HW_INIT
+ fdc_hw_init ();
+#endif
/* first, we reset the FDC via the DOR */
write_fdc_reg(FDC_DOR,0x00);
for(i=0; i<255; i++) /* then we wait some time */
udelay(500);
/* then, we clear the reset in the DOR */
- pCMD->drive=0;
+ pCMD->drive=CFG_FDC_DRIVE_NUMBER;
select_fdc_drive(pCMD);
/* initialize the CCR */
write_fdc_reg(FDC_CCR,pFG->rate);
}
/* assuming drive 0 for rest of configuration
* issue the configure command */
- pCMD->drive=0;
+ pCMD->drive=CFG_FDC_DRIVE_NUMBER;
select_fdc_drive(pCMD);
pCMD->cmd[COMMAND]=FDC_CMD_CONFIGURE;
if(fdc_issue_cmd(pCMD,pFG)==FALSE) {
switch (argc) {
case 1:
addr = CFG_LOAD_ADDR;
- boot_drive=0; /* default boot from drive 0 */
+ boot_drive=CFG_FDC_DRIVE_NUMBER;
break;
case 2:
addr = simple_strtoul(argv[1], NULL, 16);
- boot_drive=0; /* default boot from drive 0 */
+ boot_drive=CFG_FDC_DRIVE_NUMBER;
break;
case 3:
addr = simple_strtoul(argv[1], NULL, 16);
#include <stdarg.h>
#include <malloc.h>
#include <devices.h>
+#ifdef CONFIG_LOGBUFFER
+#include <logbuff.h>
+#endif
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
#include <i2c.h>
+#endif
list_t devlist = 0;
device_t *stdio_devices[] = { NULL, NULL, NULL };
#endif
#undef CFG_FPGA_CHECK_BUSY
-#define CFG_FPGA_PROG_FEEDBACK
+#undef CFG_FPGA_PROG_FEEDBACK
/* Note: The assumption is that we cannot possibly run fast enough to
* overrun the device (the Slave Parallel mode can free run at 50MHz).
static int Spartan2_ss_load (Xilinx_desc * desc, void *buf, size_t bsize)
{
- printf ("%s: Slave Serial Loading is still unsupported\n",
- __FUNCTION__);
- return FPGA_FAIL;
+ int ret_val = FPGA_FAIL; /* assume the worst */
+ Xilinx_Spartan2_Slave_Serial_fns *fn = desc->iface_fns;
+ int i;
+ char val;
+
+ PRINTF ("%s: start with interface functions @ 0x%p\n",
+ __FUNCTION__, fn);
+
+ if (fn) {
+ size_t bytecount = 0;
+ unsigned char *data = (unsigned char *) buf;
+ int cookie = desc->cookie; /* make a local copy */
+ unsigned long ts; /* timestamp */
+
+ PRINTF ("%s: Function Table:\n"
+ "ptr:\t0x%p\n"
+ "struct: 0x%p\n"
+ "pgm:\t0x%p\n"
+ "init:\t0x%p\n"
+ "clk:\t0x%p\n"
+ "wr:\t0x%p\n"
+ "done:\t0x%p\n\n",
+ __FUNCTION__, &fn, fn, fn->pgm, fn->init,
+ fn->clk, fn->wr, fn->done);
+#ifdef CFG_FPGA_PROG_FEEDBACK
+ printf ("Loading FPGA Device %d...\n", cookie);
+#endif
+
+ /*
+ * Run the pre configuration function if there is one.
+ */
+ if (*fn->pre) {
+ (*fn->pre) (cookie);
+ }
+
+ /* Establish the initial state */
+ (*fn->pgm) (TRUE, TRUE, cookie); /* Assert the program, commit */
+
+ /* Wait for INIT state (init low) */
+ ts = get_timer (0); /* get current time */
+ do {
+ CONFIG_FPGA_DELAY ();
+ if (get_timer (ts) > CFG_FPGA_WAIT) { /* check the time */
+ puts ("** Timeout waiting for INIT to start.\n");
+ return FPGA_FAIL;
+ }
+ } while (!(*fn->init) (cookie));
+
+ /* Get ready for the burn */
+ CONFIG_FPGA_DELAY ();
+ (*fn->pgm) (FALSE, TRUE, cookie); /* Deassert the program, commit */
+
+ ts = get_timer (0); /* get current time */
+ /* Now wait for INIT to go high */
+ do {
+ CONFIG_FPGA_DELAY ();
+ if (get_timer (ts) > CFG_FPGA_WAIT) { /* check the time */
+ puts ("** Timeout waiting for INIT to clear.\n");
+ return FPGA_FAIL;
+ }
+ } while ((*fn->init) (cookie));
+
+ /* Load the data */
+ while (bytecount < bsize) {
+
+ /* Xilinx detects an error if INIT goes low (active)
+ while DONE is low (inactive) */
+ if ((*fn->done) (cookie) == 0 && (*fn->init) (cookie)) {
+ puts ("** CRC error during FPGA load.\n");
+ return (FPGA_FAIL);
+ }
+ val = data [bytecount ++];
+ i = 8;
+ do {
+ /* Deassert the clock */
+ (*fn->clk) (FALSE, TRUE, cookie);
+ CONFIG_FPGA_DELAY ();
+ /* Write data */
+ (*fn->wr) ((val < 0), TRUE, cookie);
+ CONFIG_FPGA_DELAY ();
+ /* Assert the clock */
+ (*fn->clk) (TRUE, TRUE, cookie);
+ CONFIG_FPGA_DELAY ();
+ val <<= 1;
+ i --;
+ } while (i > 0);
+
+#ifdef CFG_FPGA_PROG_FEEDBACK
+ if (bytecount % (bsize / 40) == 0)
+ putc ('.'); /* let them know we are alive */
+#endif
+ }
+
+ CONFIG_FPGA_DELAY ();
+
+#ifdef CFG_FPGA_PROG_FEEDBACK
+ putc ('\n'); /* terminate the dotted line */
+#endif
+
+ /* now check for done signal */
+ ts = get_timer (0); /* get current time */
+ ret_val = FPGA_SUCCESS;
+ (*fn->wr) (TRUE, TRUE, cookie);
+
+ while (! (*fn->done) (cookie)) {
+ /* XXX - we should have a check in here somewhere to
+ * make sure we aren't busy forever... */
+
+ CONFIG_FPGA_DELAY ();
+ (*fn->clk) (FALSE, TRUE, cookie); /* Deassert the clock pin */
+ CONFIG_FPGA_DELAY ();
+ (*fn->clk) (TRUE, TRUE, cookie); /* Assert the clock pin */
+
+ putc ('*');
+
+ if (get_timer (ts) > CFG_FPGA_WAIT) { /* check the time */
+ puts ("** Timeout waiting for DONE to clear.\n");
+ ret_val = FPGA_FAIL;
+ break;
+ }
+ }
+ putc ('\n'); /* terminate the dotted line */
+
+#ifdef CFG_FPGA_PROG_FEEDBACK
+ if (ret_val == FPGA_SUCCESS) {
+ puts ("Done.\n");
+ }
+ else {
+ puts ("Fail.\n");
+ }
+#endif
+
+ } else {
+ printf ("%s: NULL Interface function table!\n", __FUNCTION__);
+ }
+
+ return ret_val;
}
static int Spartan2_ss_dump (Xilinx_desc * desc, void *buf, size_t bsize)
{
- printf ("%s: Slave Serial Dumping is still unsupported\n",
+ /* Readback is only available through the Slave Parallel and */
+ /* boundary-scan interfaces. */
+ printf ("%s: Slave Serial Dumping is unavailable\n",
__FUNCTION__);
return FPGA_FAIL;
}
static int Spartan2_ss_reloc (Xilinx_desc * desc, ulong reloc_offset)
{
int ret_val = FPGA_FAIL; /* assume the worst */
- Xilinx_Spartan2_Slave_Serial_fns *fn =
+ Xilinx_Spartan2_Slave_Serial_fns *fn_r, *fn =
(Xilinx_Spartan2_Slave_Serial_fns *) (desc->iface_fns);
if (fn) {
- printf ("%s: Slave Serial Loading is still unsupported\n",
- __FUNCTION__);
+ ulong addr;
+
+ /* Get the relocated table address */
+ addr = (ulong) fn + reloc_offset;
+ fn_r = (Xilinx_Spartan2_Slave_Serial_fns *) addr;
+
+ if (!fn_r->relocated) {
+
+ if (memcmp (fn_r, fn,
+ sizeof (Xilinx_Spartan2_Slave_Serial_fns))
+ == 0) {
+ /* good copy of the table, fix the descriptor pointer */
+ desc->iface_fns = fn_r;
+ } else {
+ PRINTF ("%s: Invalid function table at 0x%p\n",
+ __FUNCTION__, fn_r);
+ return FPGA_FAIL;
+ }
+
+ PRINTF ("%s: Relocating descriptor at 0x%p\n", __FUNCTION__,
+ desc);
+
+ addr = (ulong) (fn->pre) + reloc_offset;
+ fn_r->pre = (Xilinx_pre_fn) addr;
+
+ addr = (ulong) (fn->pgm) + reloc_offset;
+ fn_r->pgm = (Xilinx_pgm_fn) addr;
+
+ addr = (ulong) (fn->init) + reloc_offset;
+ fn_r->init = (Xilinx_init_fn) addr;
+
+ addr = (ulong) (fn->done) + reloc_offset;
+ fn_r->done = (Xilinx_done_fn) addr;
+
+ addr = (ulong) (fn->clk) + reloc_offset;
+ fn_r->clk = (Xilinx_clk_fn) addr;
+
+ addr = (ulong) (fn->wr) + reloc_offset;
+ fn_r->wr = (Xilinx_wr_fn) addr;
+
+ fn_r->relocated = TRUE;
+
+ } else {
+ /* this table has already been moved */
+ /* XXX - should check to see if the descriptor is correct */
+ desc->iface_fns = fn_r;
+ }
+
+ ret_val = FPGA_SUCCESS;
} else {
printf ("%s: NULL Interface function table!\n", __FUNCTION__);
}
AFLAGS_DEBUG := -Wa,-gstabs
AFLAGS := $(AFLAGS_DEBUG) -D__ASSEMBLY__ $(CPPFLAGS)
-LDFLAGS += -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE)
+LDFLAGS += -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS)
# Location of a usable BFD library, where we define "usable" as
# "built for ${HOST}, supports ${TARGET}". Sensible values are
/* ------------------------------------------------------------------------- */
/* NOTE: This describes the proper use of this file.
*
- * CONFIG_PLL_INPUT_FREQ should be defined as the input frequency of the PLL.
+ * CONFIG_SYS_CLK_FREQ should be defined as the input frequency of the PLL.
*
* get_FCLK(), get_HCLK(), get_PCLK() and get_UCLK() return the clock of
* the specified bus in HZ.
p = ((r & 0x003F0) >> 4) + 2;
s = r & 0x3;
- return((CONFIG_PLL_INPUT_FREQ * m) / (p << s));
+ return((CONFIG_SYS_CLK_FREQ * m) / (p << s));
}
/* return FCLK frequency */
struct eth_device* dev;
dev = (struct eth_device*) malloc(sizeof *dev);
+ memset(dev, 0, sizeof *dev);
sprintf(dev->name, "FEC ETHERNET");
dev->iobase = 0;
struct eth_device* dev;
dev = (struct eth_device*) malloc(sizeof *dev);
+ memset(dev, 0, sizeof *dev);
sprintf(dev->name, "SCC ETHERNET");
dev->iobase = 0;
#define OIER 0x1C
/* Clock Manager Registers */
+#ifdef CFG_CPUSPEED
CC_BASE: .word 0x41300000
#define CCCR 0x00
cpuspeed: .word CFG_CPUSPEED
-
+#endif
/* RS: ??? */
.macro CPWAIT
mrc p15,0,r0,c2,c0,0
mov r1, #0x00
str r1, [r0, #ICMR]
+#ifdef CFG_CPUSPEED
/* set clock speed */
ldr r0, CC_BASE
ldr r1, cpuspeed
str r1, [r0, #CCCR]
+ mov r0, #3
+ mcr p14, 0, r0, c6, c0, 0
+#endif
/*
* before relocating, we have to setup RAM timing
/* $(BOARD)/$(BOARD).c */
void reset_phy (void);
+void fdc_hw_init (void);
/* $(BOARD)/eeprom.c */
void eeprom_init (void);
#define CONFIG_SMDK2400 1 /* on an SAMSUNG SMDK2400 Board */
/* input clock of PLL */
-#define CONFIG_PLL_INPUT_FREQ 12000000 /* SMDK2400 has 12 MHz input clock */
+#define CONFIG_SYS_CLK_FREQ 12000000 /* SMDK2400 has 12 MHz input clock */
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SMDK2410 1 /* on a SAMSUNG SMDK2410 Board */
/* input clock of PLL */
-#define CONFIG_PLL_INPUT_FREQ 12000000/* the SMDK2410 has 12MHz input clock */
+#define CONFIG_SYS_CLK_FREQ 12000000/* the SMDK2410 has 12MHz input clock */
#define USE_920T_MMU 1
#undef CONFIG_TRAB_50MHZ /* run the CPU at 50 MHz */
/* input clock of PLL */
-#define CONFIG_PLL_INPUT_FREQ 12000000 /* TRAB has 12 MHz input clock */
+#define CONFIG_SYS_CLK_FREQ 12000000 /* TRAB has 12 MHz input clock */
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
/* Slave Serial Implementation function table */
typedef struct {
+ Xilinx_pre_fn pre;
Xilinx_pgm_fn pgm;
Xilinx_clk_fn clk;
- Xilinx_rdata_fn rdata;
- Xilinx_wdata_fn wdata;
+ Xilinx_init_fn init;
+ Xilinx_done_fn done;
+ Xilinx_wr_fn wr;
int relocated;
} Xilinx_Spartan2_Slave_Serial_fns;
if (eth_current->init(eth_current, bis)) {
eth_current->state = ETH_STATE_ACTIVE;
- printf("%s configured\n", eth_current->name);
return 1;
}
#
PLATFORM_CPPFLAGS += -DCONFIG_PPC -D__powerpc__
+PLATFORM_LDFLAGS += -n
projects / karo-tx-uboot.git / commitdiff