======================================================================
-Changes since U-Boot 0.2.0:
+Changes since U-Boot 0.2.1:
+======================================================================
+
+* Add dual ethernet support on PM826
+
+* Add support for LXT971 PHY on PM826
+
+* Patch by Tord Andersson, 16 Jan 2003:
+ Fix flash sector count for TQM8xxL
+
+* Fix I2C EEPROM problem on ICU862 board (would only write the first
+ 16 bytes out of each 32 byte block)
+
+======================================================================
+Changes for U-Boot 0.2.1:
======================================================================
* Add support for V37 board
/* Port B configuration */
{ /* conf ppar psor pdir podr pdat */
- /* PB31 */ { 0, 1, 0, 1, 0, 0 }, /* PB31 */
- /* PB30 */ { 0, 1, 0, 0, 0, 0 }, /* PB30 */
- /* PB29 */ { 0, 1, 1, 1, 0, 0 }, /* PB29 */
+ /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 TX_ER */
+ /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 RX_DV */
+ /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 TX_EN */
+#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1)
+#ifdef CONFIG_ETHER_ON_FCC2
+#error "SCC1 conflicts with FCC2"
+#endif
/* PB28 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 TXD */
- /* PB27 */ { 0, 1, 0, 0, 0, 0 }, /* PB27 */
- /* PB26 */ { 0, 1, 0, 0, 0, 0 }, /* PB26 */
- /* PB25 */ { 0, 1, 0, 1, 0, 0 }, /* PB25 */
- /* PB24 */ { 0, 1, 0, 1, 0, 0 }, /* PB24 */
- /* PB23 */ { 0, 1, 0, 1, 0, 0 }, /* PB23 */
- /* PB22 */ { 0, 1, 0, 1, 0, 0 }, /* PB22 */
- /* PB21 */ { 0, 1, 0, 0, 0, 0 }, /* PB21 */
- /* PB20 */ { 0, 1, 0, 0, 0, 0 }, /* PB20 */
- /* PB19 */ { 0, 1, 0, 0, 0, 0 }, /* PB19 */
- /* PB18 */ { 0, 1, 0, 0, 0, 0 }, /* PB18 */
+#else
+ /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 RX_ER */
+#endif
+ /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 COL */
+ /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 CRS */
+ /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 TxD[3] */
+ /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 TxD[2] */
+ /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 TxD[1] */
+ /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 TxD[0] */
+ /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 RxD[0] */
+ /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 RxD[1] */
+ /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 RxD[2] */
+ /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 RxD[3] */
/* PB17 */ { 0, 0, 0, 0, 0, 0 }, /* PB17 */
/* PB16 */ { 0, 0, 0, 0, 0, 0 }, /* PB16 */
/* PB15 */ { 1, 1, 0, 0, 0, 0 }, /* SCC2 RXD */
/* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* PC23 */
/* PC22 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 TXCK */
/* PC21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 RXCK */
- /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* PC20 */
- /* PC19 */ { 0, 1, 0, 0, 0, 0 }, /* PC19 */
- /* PC18 */ { 0, 1, 0, 0, 0, 0 }, /* PC18 */
+ /* PC20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 TXCK(2) */
+ /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 RXCK */
+ /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 TXCK */
/* PC17 */ { 0, 0, 0, 1, 0, 0 }, /* PC17 */
/* PC16 */ { 0, 0, 0, 1, 0, 0 }, /* PC16 */
/* PC15 */ { 1, 1, 0, 1, 0, 0 }, /* SMC2 TXD */
*/
contr_reg[0] = 0;
for (i = 0; i < MAX_ACKNOWLEDGE_POLLS; i++) {
- if (i2c_read (addr_void[0], addr_void[1], 1, contr_reg, 1) == 1)
+ if (i2c_read (addr_void[0], addr_void[1], 1, contr_reg, 1) == 0)
break; /* got ack */
#if defined(CFG_EEPROM_PAGE_WRITE_DELAY_MS)
udelay(CFG_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
*/
#include <common.h>
+#include <malloc.h>
#include <asm/cpm_8260.h>
#include <mpc8260.h>
-#include <net.h>
#include <command.h>
#include <config.h>
+#include <net.h>
-#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_COMMANDS & CFG_CMD_NET)
-
-/*---------------------------------------------------------------------*/
-#if (CONFIG_ETHER_INDEX == 1)
-
-#define PROFF_ENET PROFF_FCC1
-#define CPM_CR_ENET_SBLOCK CPM_CR_FCC1_SBLOCK
-#define CPM_CR_ENET_SBLOCK CPM_CR_FCC1_SBLOCK
-#define CPM_CR_ENET_PAGE CPM_CR_FCC1_PAGE
-
-/*---------------------------------------------------------------------*/
-#elif (CONFIG_ETHER_INDEX == 2)
-
-#define PROFF_ENET PROFF_FCC2
-#define CPM_CR_ENET_SBLOCK CPM_CR_FCC2_SBLOCK
-#define CPM_CR_ENET_PAGE CPM_CR_FCC2_PAGE
+#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_COMMANDS & CFG_CMD_NET) && \
+ defined(CONFIG_NET_MULTI)
-/*---------------------------------------------------------------------*/
-#elif (CONFIG_ETHER_INDEX == 3)
+static struct ether_fcc_info_s
+{
+ int ether_index;
+ int proff_enet;
+ ulong cpm_cr_enet_sblock;
+ ulong cpm_cr_enet_page;
+ ulong cmxfcr_mask;
+ ulong cmxfcr_value;
+}
+ ether_fcc_info[] =
+{
+#ifdef CONFIG_ETHER_ON_FCC1
+{
+ 0,
+ PROFF_FCC1,
+ CPM_CR_FCC1_SBLOCK,
+ CPM_CR_FCC1_PAGE,
+ CFG_CMXFCR_MASK1,
+ CFG_CMXFCR_VALUE1
+},
+#endif
-#define PROFF_ENET PROFF_FCC3
-#define CPM_CR_ENET_SBLOCK CPM_CR_FCC3_SBLOCK
-#define CPM_CR_ENET_PAGE CPM_CR_FCC3_PAGE
+#ifdef CONFIG_ETHER_ON_FCC2
+{
+ 1,
+ PROFF_FCC2,
+ CPM_CR_FCC2_SBLOCK,
+ CPM_CR_FCC2_PAGE,
+ CFG_CMXFCR_MASK2,
+ CFG_CMXFCR_VALUE2
+},
+#endif
-/*---------------------------------------------------------------------*/
-#else
-#error "FCC Ethernet not correctly defined"
+#ifdef CONFIG_ETHER_ON_FCC3
+{
+ 2,
+ PROFF_FCC3,
+ CPM_CR_FCC3_SBLOCK,
+ CPM_CR_FCC3_PAGE,
+ CFG_CMXFCR_MASK3,
+ CFG_CMXFCR_VALUE3
+},
#endif
+};
+
/*---------------------------------------------------------------------*/
/* Maximum input DMA size. Must be a should(?) be a multiple of 4. */
#error "rtx must be 64-bit aligned"
#endif
-int eth_send(volatile void *packet, int length)
+static int fec_send(struct eth_device* dev, volatile void *packet, int length)
{
int i;
int result = 0;
return result;
}
-int eth_rx(void)
+static int fec_recv(struct eth_device* dev)
{
int length;
}
-int eth_init(bd_t *bis)
+static int fec_init(struct eth_device* dev, bd_t *bis)
{
+ struct ether_fcc_info_s * info = dev->priv;
int i;
volatile immap_t *immr = (immap_t *)CFG_IMMR;
volatile cpm8260_t *cp = &(immr->im_cpm);
/* 28.9 - (3): connect FCC's tx and rx clocks */
immr->im_cpmux.cmx_uar = 0;
- immr->im_cpmux.cmx_fcr = (immr->im_cpmux.cmx_fcr & ~CFG_CMXFCR_MASK) |
- CFG_CMXFCR_VALUE;
+ immr->im_cpmux.cmx_fcr = (immr->im_cpmux.cmx_fcr & ~info->cmxfcr_mask) |
+ info->cmxfcr_value;
/* 28.9 - (4): GFMR: disable tx/rx, CCITT CRC, Mode Ethernet */
- immr->im_fcc[CONFIG_ETHER_INDEX-1].fcc_gfmr =
+ immr->im_fcc[info->ether_index].fcc_gfmr =
FCC_GFMR_MODE_ENET | FCC_GFMR_TCRC_32;
/* 28.9 - (5): FPSMR: enable full duplex, select CCITT CRC for Ethernet */
- immr->im_fcc[CONFIG_ETHER_INDEX-1].fcc_fpsmr = CFG_FCC_PSMR | FCC_PSMR_ENCRC;
+ immr->im_fcc[info->ether_index].fcc_fpsmr = CFG_FCC_PSMR | FCC_PSMR_ENCRC;
/* 28.9 - (6): FDSR: Ethernet Syn */
- immr->im_fcc[CONFIG_ETHER_INDEX-1].fcc_fdsr = 0xD555;
+ immr->im_fcc[info->ether_index].fcc_fdsr = 0xD555;
/* reset indeces to current rx/tx bd (see eth_send()/eth_rx()) */
rxIdx = 0;
rtx.txbd[TX_BUF_CNT - 1].cbd_sc |= BD_ENET_TX_WRAP;
/* 28.9 - (7): initialise parameter ram */
- pram_ptr = (fcc_enet_t *)&(immr->im_dprambase[PROFF_ENET]);
+ pram_ptr = (fcc_enet_t *)&(immr->im_dprambase[info->proff_enet]);
/* clear whole structure to make sure all reserved fields are zero */
memset((void*)pram_ptr, 0, sizeof(fcc_enet_t));
* can do this. Later, we will add resource management for
* this area.
*/
- mem_addr = CPM_FCC_SPECIAL_BASE + ((CONFIG_ETHER_INDEX-1) * 64);
+ mem_addr = CPM_FCC_SPECIAL_BASE + ((info->ether_index) * 64);
pram_ptr->fen_genfcc.fcc_riptr = mem_addr;
pram_ptr->fen_genfcc.fcc_tiptr = mem_addr+32;
/*
* it unique by setting a few bits in the upper byte of the
* non-static part of the address.
*/
-#define ea bis->bi_enetaddr
+#define ea eth_get_dev()->enetaddr
pram_ptr->fen_paddrh = (ea[5] << 8) + ea[4];
pram_ptr->fen_paddrm = (ea[3] << 8) + ea[2];
pram_ptr->fen_paddrl = (ea[1] << 8) + ea[0];
#endif
/* 28.9 - (8): clear out events in FCCE */
- immr->im_fcc[CONFIG_ETHER_INDEX-1].fcc_fcce = ~0x0;
+ immr->im_fcc[info->ether_index].fcc_fcce = ~0x0;
/* 28.9 - (9): FCCM: mask all events */
- immr->im_fcc[CONFIG_ETHER_INDEX-1].fcc_fccm = 0;
+ immr->im_fcc[info->ether_index].fcc_fccm = 0;
/* 28.9 - (10-12): we don't use ethernet interrupts */
* than the manual describes because we have just now finished
* the BD initialization.
*/
- cp->cp_cpcr = mk_cr_cmd(CPM_CR_ENET_PAGE,
- CPM_CR_ENET_SBLOCK,
+ cp->cp_cpcr = mk_cr_cmd(info->cpm_cr_enet_page,
+ info->cpm_cr_enet_sblock,
0x0c,
CPM_CR_INIT_TRX) | CPM_CR_FLG;
do {
} while (cp->cp_cpcr & CPM_CR_FLG);
/* 28.9 - (14): enable tx/rx in gfmr */
- immr->im_fcc[CONFIG_ETHER_INDEX-1].fcc_gfmr |= FCC_GFMR_ENT | FCC_GFMR_ENR;
+ immr->im_fcc[info->ether_index].fcc_gfmr |= FCC_GFMR_ENT | FCC_GFMR_ENR;
return 1;
}
-void eth_halt(void)
+static void fec_halt(struct eth_device* dev)
{
+ struct ether_fcc_info_s * info = dev->priv;
volatile immap_t *immr = (immap_t *)CFG_IMMR;
/* write GFMR: disable tx/rx */
- immr->im_fcc[CONFIG_ETHER_INDEX-1].fcc_gfmr &=
+ immr->im_fcc[info->ether_index].fcc_gfmr &=
~(FCC_GFMR_ENT | FCC_GFMR_ENR);
}
-#endif /* CONFIG_ETHER_ON_FCC && CFG_CMD_NET */
+int fec_initialize(bd_t *bis)
+{
+ struct eth_device* dev;
+ int i;
+
+ for (i = 0; i < sizeof(ether_fcc_info) / sizeof(ether_fcc_info[0]); i++)
+ {
+ dev = (struct eth_device*) malloc(sizeof *dev);
+ memset(dev, 0, sizeof *dev);
+
+ sprintf(dev->name, "FCC%d ETHERNET",
+ ether_fcc_info[i].ether_index + 1);
+ dev->priv = ðer_fcc_info[i];
+ dev->init = fec_init;
+ dev->halt = fec_halt;
+ dev->send = fec_send;
+ dev->recv = fec_recv;
+
+ eth_register(dev);
+ }
+
+ return 1;
+}
+
+#endif /* CONFIG_ETHER_ON_FCC && CFG_CMD_NET && CONFIG_NET_MULTI */
#define CONFIG_MPC8260 1 /* This is a MPC8260 CPU */
#define CONFIG_PM826 1 /* ...on a PM8260 module */
+#undef CONFIG_DB_CR826_J30x_ON /* J30x jumpers on D.B. carrier */
+
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
/*
* select ethernet configuration
*
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
+ * if CONFIG_ETHER_ON_SCC is selected, then
+ * - CONFIG_ETHER_INDEX must be set to the channel number (1-4)
+ * - CONFIG_NET_MULTI must not be defined
+ *
+ * if CONFIG_ETHER_ON_FCC is selected, then
+ * - one or more CONFIG_ETHER_ON_FCCx (x=1,2,3) must also be selected
+ * - CONFIG_NET_MULTI must be defined
*
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
* defined elsewhere (as for the console), or CFG_CMD_NET must be removed
* from CONFIG_COMMANDS to remove support for networking.
*/
-#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
-#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
+#define CONFIG_NET_MULTI
#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 1 /* which SCC/FCC channel for ethernet */
-#if (CONFIG_ETHER_INDEX == 1)
+#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
+#define CONFIG_ETHER_INDEX 1 /* which SCC channel for ethernet */
+
+#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
/*
* - Rx-CLK is CLK11
* - Tx-CLK is CLK10
+ */
+#define CONFIG_ETHER_ON_FCC1
+# define CFG_CMXFCR_MASK1 (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
+#ifndef CONFIG_DB_CR826_J30x_ON
+# define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10)
+#else
+# define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
+#endif
+/*
+ * - Rx-CLK is CLK15
+ * - Tx-CLK is CLK14
+ */
+#define CONFIG_ETHER_ON_FCC2
+# define CFG_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+# define CFG_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+/*
* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
* - Enable Full Duplex in FSMR
*/
-# define CFG_CMXFCR_MASK (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
-# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10)
# define CFG_CPMFCR_RAMTYPE 0
# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
-#endif /* CONFIG_ETHER_INDEX */
-
/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
#define CONFIG_8260_CLKIN 64000000 /* in Hz */
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_NET_MULTI
#endif
#endif
+
+#if !defined(CONFIG_NET_MULTI) && defined(CONFIG_8260)
+#include <config.h>
+#if defined(CONFIG_ETHER_ON_FCC)
+#if defined(CONFIG_ETHER_ON_SCC)
+#error "Ethernet not correctly defined"
+#endif /* CONFIG_ETHER_ON_SCC */
+#define CONFIG_NET_MULTI
+#if (CONFIG_ETHER_INDEX == 1)
+#define CONFIG_ETHER_ON_FCC1
+# define CFG_CMXFCR_MASK1 CFG_CMXFCR_MASK
+# define CFG_CMXFCR_VALUE1 CFG_CMXFCR_VALUE
+#elif (CONFIG_ETHER_INDEX == 2)
+#define CONFIG_ETHER_ON_FCC2
+# define CFG_CMXFCR_MASK2 CFG_CMXFCR_MASK
+# define CFG_CMXFCR_VALUE2 CFG_CMXFCR_VALUE
+#elif (CONFIG_ETHER_INDEX == 3)
+#define CONFIG_ETHER_ON_FCC3
+# define CFG_CMXFCR_MASK3 CFG_CMXFCR_MASK
+# define CFG_CMXFCR_VALUE3 CFG_CMXFCR_VALUE
+#endif /* CONFIG_ETHER_INDEX */
+#endif /* CONFIG_ETHER_ON_FCC */
+#endif /* !CONFIG_NET_MULTI && CONFIG_8260 */
+
#include <asm/byteorder.h> /* for nton* / ntoh* stuff */
#ifdef SCC_ENET
scc_initialize(bis);
#endif
-#ifdef FEC_ENET
+#if defined(FEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
fec_initialize(bis);
#endif
projects / karo-tx-uboot.git / commitdiff