--- /dev/null
+/*
+ * S3C24xx SD/MMC driver
+ *
+ * Based on OpenMoko S3C24xx driver by Harald Welte <laforge@openmoko.org>
+ *
+ * Copyright (C) 2014 Marek Vasut <marex@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <mmc.h>
+#include <errno.h>
+#include <asm/arch/s3c24x0_cpu.h>
+#include <asm/io.h>
+#include <asm/unaligned.h>
+
+#define S3C2440_SDICON_SDRESET (1 << 8)
+#define S3C2410_SDICON_FIFORESET (1 << 1)
+#define S3C2410_SDICON_CLOCKTYPE (1 << 0)
+
+#define S3C2410_SDICMDCON_LONGRSP (1 << 10)
+#define S3C2410_SDICMDCON_WAITRSP (1 << 9)
+#define S3C2410_SDICMDCON_CMDSTART (1 << 8)
+#define S3C2410_SDICMDCON_SENDERHOST (1 << 6)
+#define S3C2410_SDICMDCON_INDEX 0x3f
+
+#define S3C2410_SDICMDSTAT_CRCFAIL (1 << 12)
+#define S3C2410_SDICMDSTAT_CMDSENT (1 << 11)
+#define S3C2410_SDICMDSTAT_CMDTIMEOUT (1 << 10)
+#define S3C2410_SDICMDSTAT_RSPFIN (1 << 9)
+
+#define S3C2440_SDIDCON_DS_WORD (2 << 22)
+#define S3C2410_SDIDCON_TXAFTERRESP (1 << 20)
+#define S3C2410_SDIDCON_RXAFTERCMD (1 << 19)
+#define S3C2410_SDIDCON_BLOCKMODE (1 << 17)
+#define S3C2410_SDIDCON_WIDEBUS (1 << 16)
+#define S3C2440_SDIDCON_DATSTART (1 << 14)
+#define S3C2410_SDIDCON_XFER_RXSTART (2 << 12)
+#define S3C2410_SDIDCON_XFER_TXSTART (3 << 12)
+#define S3C2410_SDIDCON_BLKNUM 0x7ff
+
+#define S3C2410_SDIDSTA_FIFOFAIL (1 << 8)
+#define S3C2410_SDIDSTA_CRCFAIL (1 << 7)
+#define S3C2410_SDIDSTA_RXCRCFAIL (1 << 6)
+#define S3C2410_SDIDSTA_DATATIMEOUT (1 << 5)
+#define S3C2410_SDIDSTA_XFERFINISH (1 << 4)
+
+#define S3C2410_SDIFSTA_TFHALF (1 << 11)
+#define S3C2410_SDIFSTA_COUNTMASK 0x7f
+
+/*
+ * WARNING: We only support one SD IP block.
+ * NOTE: It's not likely there will ever exist an S3C24xx with two,
+ * at least not in this universe all right.
+ */
+static int wide_bus;
+
+static int
+s3cmmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
+{
+ struct s3c24x0_sdi *sdi_regs = s3c24x0_get_base_sdi();
+ uint32_t sdiccon, sdicsta, sdidcon, sdidsta, sdidat, sdifsta;
+ uint32_t sdicsta_wait_bit = S3C2410_SDICMDSTAT_CMDSENT;
+ unsigned int timeout = 100000;
+ int ret = 0, xfer_len, data_offset = 0;
+ const uint32_t sdidsta_err_mask = S3C2410_SDIDSTA_FIFOFAIL |
+ S3C2410_SDIDSTA_CRCFAIL | S3C2410_SDIDSTA_RXCRCFAIL |
+ S3C2410_SDIDSTA_DATATIMEOUT;
+
+
+ writel(0xffffffff, &sdi_regs->sdicsta);
+ writel(0xffffffff, &sdi_regs->sdidsta);
+ writel(0xffffffff, &sdi_regs->sdifsta);
+
+ /* Set up data transfer (if applicable). */
+ if (data) {
+ writel(data->blocksize, &sdi_regs->sdibsize);
+
+ sdidcon = data->blocks & S3C2410_SDIDCON_BLKNUM;
+ sdidcon |= S3C2410_SDIDCON_BLOCKMODE;
+#if defined(CONFIG_S3C2440)
+ sdidcon |= S3C2440_SDIDCON_DS_WORD | S3C2440_SDIDCON_DATSTART;
+#endif
+ if (wide_bus)
+ sdidcon |= S3C2410_SDIDCON_WIDEBUS;
+
+ if (data->flags & MMC_DATA_READ) {
+ sdidcon |= S3C2410_SDIDCON_RXAFTERCMD;
+ sdidcon |= S3C2410_SDIDCON_XFER_RXSTART;
+ } else {
+ sdidcon |= S3C2410_SDIDCON_TXAFTERRESP;
+ sdidcon |= S3C2410_SDIDCON_XFER_TXSTART;
+ }
+
+ writel(sdidcon, &sdi_regs->sdidcon);
+ }
+
+ /* Write CMD arg. */
+ writel(cmd->cmdarg, &sdi_regs->sdicarg);
+
+ /* Write CMD index. */
+ sdiccon = cmd->cmdidx & S3C2410_SDICMDCON_INDEX;
+ sdiccon |= S3C2410_SDICMDCON_SENDERHOST;
+ sdiccon |= S3C2410_SDICMDCON_CMDSTART;
+
+ /* Command with short response. */
+ if (cmd->resp_type & MMC_RSP_PRESENT) {
+ sdiccon |= S3C2410_SDICMDCON_WAITRSP;
+ sdicsta_wait_bit = S3C2410_SDICMDSTAT_RSPFIN;
+ }
+
+ /* Command with long response. */
+ if (cmd->resp_type & MMC_RSP_136)
+ sdiccon |= S3C2410_SDICMDCON_LONGRSP;
+
+ /* Start the command. */
+ writel(sdiccon, &sdi_regs->sdiccon);
+
+ /* Wait for the command to complete or for response. */
+ for (timeout = 100000; timeout; timeout--) {
+ sdicsta = readl(&sdi_regs->sdicsta);
+ if (sdicsta & sdicsta_wait_bit)
+ break;
+
+ if (sdicsta & S3C2410_SDICMDSTAT_CMDTIMEOUT)
+ timeout = 1;
+ }
+
+ /* Clean the status bits. */
+ setbits_le32(&sdi_regs->sdicsta, 0xf << 9);
+
+ if (!timeout) {
+ puts("S3C SDI: Command timed out!\n");
+ ret = TIMEOUT;
+ goto error;
+ }
+
+ /* Read out the response. */
+ if (cmd->resp_type & MMC_RSP_136) {
+ cmd->response[0] = readl(&sdi_regs->sdirsp0);
+ cmd->response[1] = readl(&sdi_regs->sdirsp1);
+ cmd->response[2] = readl(&sdi_regs->sdirsp2);
+ cmd->response[3] = readl(&sdi_regs->sdirsp3);
+ } else {
+ cmd->response[0] = readl(&sdi_regs->sdirsp0);
+ }
+
+ /* If there are no data, we're done. */
+ if (!data)
+ return 0;
+
+ xfer_len = data->blocksize * data->blocks;
+
+ while (xfer_len > 0) {
+ sdidsta = readl(&sdi_regs->sdidsta);
+ sdifsta = readl(&sdi_regs->sdifsta);
+
+ if (sdidsta & sdidsta_err_mask) {
+ printf("S3C SDI: Data error (sdta=0x%08x)\n", sdidsta);
+ ret = -EIO;
+ goto error;
+ }
+
+ if (data->flags & MMC_DATA_READ) {
+ if ((sdifsta & S3C2410_SDIFSTA_COUNTMASK) < 4)
+ continue;
+ sdidat = readl(&sdi_regs->sdidat);
+ put_unaligned_le32(sdidat, data->dest + data_offset);
+ } else { /* Write */
+ /* TX FIFO half full. */
+ if (!(sdifsta & S3C2410_SDIFSTA_TFHALF))
+ continue;
+
+ /* TX FIFO is below 32b full, write. */
+ sdidat = get_unaligned_le32(data->src + data_offset);
+ writel(sdidat, &sdi_regs->sdidat);
+ }
+ data_offset += 4;
+ xfer_len -= 4;
+ }
+
+ /* Wait for the command to complete or for response. */
+ for (timeout = 100000; timeout; timeout--) {
+ sdidsta = readl(&sdi_regs->sdidsta);
+ if (sdidsta & S3C2410_SDIDSTA_XFERFINISH)
+ break;
+
+ if (sdidsta & S3C2410_SDIDSTA_DATATIMEOUT)
+ timeout = 1;
+ }
+
+ /* Clear status bits. */
+ writel(0x6f8, &sdi_regs->sdidsta);
+
+ if (!timeout) {
+ puts("S3C SDI: Command timed out!\n");
+ ret = TIMEOUT;
+ goto error;
+ }
+
+ writel(0, &sdi_regs->sdidcon);
+
+ return 0;
+error:
+ return ret;
+}
+
+static void s3cmmc_set_ios(struct mmc *mmc)
+{
+ struct s3c24x0_sdi *sdi_regs = s3c24x0_get_base_sdi();
+ uint32_t divider = 0;
+
+ wide_bus = (mmc->bus_width == 4);
+
+ if (!mmc->clock)
+ return;
+
+ divider = DIV_ROUND_UP(get_PCLK(), mmc->clock);
+ if (divider)
+ divider--;
+
+ writel(divider, &sdi_regs->sdipre);
+ mdelay(125);
+}
+
+static int s3cmmc_init(struct mmc *mmc)
+{
+ struct s3c24x0_clock_power *clk_power = s3c24x0_get_base_clock_power();
+ struct s3c24x0_sdi *sdi_regs = s3c24x0_get_base_sdi();
+
+ /* Start the clock. */
+ setbits_le32(&clk_power->clkcon, 1 << 9);
+
+#if defined(CONFIG_S3C2440)
+ writel(S3C2440_SDICON_SDRESET, &sdi_regs->sdicon);
+ mdelay(10);
+ writel(0x7fffff, &sdi_regs->sdidtimer);
+#else
+ writel(0xffff, &sdi_regs->sdidtimer);
+#endif
+ writel(MMC_MAX_BLOCK_LEN, &sdi_regs->sdibsize);
+ writel(0x0, &sdi_regs->sdiimsk);
+
+ writel(S3C2410_SDICON_FIFORESET | S3C2410_SDICON_CLOCKTYPE,
+ &sdi_regs->sdicon);
+
+ mdelay(125);
+
+ return 0;
+}
+
+struct s3cmmc_priv {
+ struct mmc_config cfg;
+ int (*getcd)(struct mmc *);
+ int (*getwp)(struct mmc *);
+};
+
+static int s3cmmc_getcd(struct mmc *mmc)
+{
+ struct s3cmmc_priv *priv = mmc->priv;
+ if (priv->getcd)
+ return priv->getcd(mmc);
+ else
+ return 0;
+}
+
+static int s3cmmc_getwp(struct mmc *mmc)
+{
+ struct s3cmmc_priv *priv = mmc->priv;
+ if (priv->getwp)
+ return priv->getwp(mmc);
+ else
+ return 0;
+}
+
+static const struct mmc_ops s3cmmc_ops = {
+ .send_cmd = s3cmmc_send_cmd,
+ .set_ios = s3cmmc_set_ios,
+ .init = s3cmmc_init,
+ .getcd = s3cmmc_getcd,
+ .getwp = s3cmmc_getwp,
+};
+
+int s3cmmc_initialize(bd_t *bis, int (*getcd)(struct mmc *),
+ int (*getwp)(struct mmc *))
+{
+ struct s3cmmc_priv *priv;
+ struct mmc *mmc;
+ struct mmc_config *cfg;
+
+ priv = calloc(1, sizeof(*priv));
+ if (!priv)
+ return -ENOMEM;
+ cfg = &priv->cfg;
+
+ cfg->name = "S3C MMC";
+ cfg->ops = &s3cmmc_ops;
+ cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34;
+ cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_HC | MMC_MODE_HS;
+ cfg->f_min = 400000;
+ cfg->f_max = get_PCLK() / 2;
+ cfg->b_max = 0x80;
+
+#if defined(CONFIG_S3C2410)
+ /*
+ * S3C2410 has some bug that prevents reliable
+ * operation at higher speed
+ */
+ cfg->f_max /= 2;
+#endif
+
+ mmc = mmc_create(cfg, priv);
+ if (!mmc) {
+ free(priv);
+ return -ENOMEM;
+ }
+
+ return 0;
+}
projects / karo-tx-uboot.git / commitdiff