VERSION = 2012
PATCHLEVEL = 04
SUBLEVEL =
-EXTRAVERSION = -rc1
+EXTRAVERSION = -rc2
ifneq "$(SUBLEVEL)" ""
U_BOOT_VERSION = $(VERSION).$(PATCHLEVEL).$(SUBLEVEL)$(EXTRAVERSION)
else
int mmcif_mmc_init(void);
#endif /* _SH_MMC_H_ */
-
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
-#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
#define SPI_PAD_CTRL (PAD_CTL_HYS | \
int ret;
if (cfg->esdhc_base == USDHC3_BASE_ADDR) {
- gpio_direction_input(192); /*GPIO7_0*/
- ret = !gpio_get_value(192);
+ gpio_direction_input(192); /*GPIO7_0*/
+ ret = !gpio_get_value(192);
} else {
- gpio_direction_input(38); /*GPIO2_6*/
- ret = !gpio_get_value(38);
+ gpio_direction_input(38); /*GPIO2_6*/
+ ret = !gpio_get_value(38);
}
return ret;
u32 index = 0;
for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
- switch (index) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(
- usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
- break;
- case 1:
- imx_iomux_v3_setup_multiple_pads(
- usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
- break;
- default:
- printf("Warning: you configured more USDHC controllers"
- "(%d) then supported by the board (%d)\n",
- index + 1, CONFIG_SYS_FSL_USDHC_NUM);
- return status;
- }
-
- status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
+ switch (index) {
+ case 0:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+ break;
+ case 1:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+ break;
+ default:
+ printf("Warning: you configured more USDHC controllers"
+ "(%d) then supported by the board (%d)\n",
+ index + 1, CONFIG_SYS_FSL_USDHC_NUM);
+ return status;
+ }
+
+ status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
}
return status;
MII_KSZ9021_EXT_RGMII_CLOCK_SKEW, 0xf0f0);
if (phydev->drv->config)
phydev->drv->config(phydev);
-
+
return 0;
}
Choice #1 does not enable CONFIG_PCI, and assumes that the PCI slot
will be left empty (M66EN high), and so the board will operate with
-a base clock of 66MHz. Note that you need both PCI enabled in u-boot
+a base clock of 66MHz. Note that you need both PCI enabled in u-boot
and linux in order to have functional PCI under linux.
The second enables PCI support and builds for a 33MHz clock rate. Note
to reflect a different CCB:SYSCLK ratio]
The third option builds PCI support in, and leaves the clocking at the
-default 66MHz. Options four and five are just repeats of option two
+default 66MHz. Options four and five are just repeats of option two
and three, but with PCI-e support enabled as well.
PCI output listing with an intel e1000 PCI-x and a Syskonnect SK-9Exx
-is shown below for sbc8548_PCI_66_PCIE_config. (Note that PCI-e with
+is shown below for sbc8548_PCI_66_PCIE_config. (Note that PCI-e with
a 33MHz PCI configuration is currently untested.)
=> pci 0
Scanning PCI devices on bus 0
- BusDevFun VendorId DeviceId Device Class Sub-Class
+ BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
- 00.00.00 0x1057 0x0012 Processor 0x20
- 00.01.00 0x8086 0x1026 Network controller 0x00
+ 00.00.00 0x1057 0x0012 Processor 0x20
+ 00.01.00 0x8086 0x1026 Network controller 0x00
=> pci 1
Scanning PCI devices on bus 1
- BusDevFun VendorId DeviceId Device Class Sub-Class
+ BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
- 01.00.00 0x1957 0x0012 Processor 0x20
+ 01.00.00 0x1957 0x0012 Processor 0x20
=> pci 2
Scanning PCI devices on bus 2
- BusDevFun VendorId DeviceId Device Class Sub-Class
+ BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
- 02.00.00 0x1148 0x9e00 Network controller 0x00
+ 02.00.00 0x1148 0x9e00 Network controller 0x00
=>
Memory Size and using SPD:
fix has been applied:
1) Remove R314 (RES-R0174-033, 1K, 0603). R314 is located on
- the back of the PCB behind the DDR SDRAM SODIMM connector.
+ the back of the PCB behind the DDR SDRAM SODIMM connector.
2) Solder RES-R0174-033 (1K, 0603) resistor from R314 pin 2 pad
- to R313 pin 2. Pin 2 for each resistor is the end of the
- resistor closest to the CPU.
+ to R313 pin 2. Pin 2 for each resistor is the end of the
+ resistor closest to the CPU.
Boards without the mod will have R314 and R313 in parallel, like "||".
After the mod, they will be touching and form an "L" shape.
===================
The following contains some summary information on hardware settings
-that are relevant to u-boot, based on the board manual. For the
+that are relevant to u-boot, based on the board manual. For the
most up to date and complete details of the board, please request the
reference manual ERG-00327-001.pdf from www.windriver.com
Required properties:
- clocks : Two clocks must be given, each as a phandle to the Tegra's
- CAR node and the clock number as a parameter:
+ CAR node and the clock number as a parameter:
- the I2C clock to use for the peripheral
- the pll_p_out3 clock, which can be used for fast operation. This
- does not change and is the same for all I2C nodes.
+ does not change and is the same for all I2C nodes.
Example:
(TODO: merge with existing example):
dev, pipe, buffer, length, interval);
return ehci_submit_async(dev, pipe, buffer, length, NULL);
}
-
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
#define __CONFIG_H
#define CONFIG_MX6Q
-#define CONFIG_SYS_MX6_HCLK 24000000
-#define CONFIG_SYS_MX6_CLK32 32768
+#define CONFIG_SYS_MX6_HCLK 24000000
+#define CONFIG_SYS_MX6_CLK32 32768
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_REVISION_TAG
/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_MXC_GPIO
#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART2_BASE
+#define CONFIG_MXC_UART_BASE UART2_BASE
#define CONFIG_CMD_SF
#ifdef CONFIG_CMD_SF
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
-#define CONFIG_FEC_MXC
-#define CONFIG_MII
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
+#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 6
#define CONFIG_PHYLIB
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
/* Command definition */
#undef CONFIG_CMD_IMLS
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 3
-#define CONFIG_LOADADDR 0x10800000
-#define CONFIG_SYS_TEXT_BASE 0x17800000
+#define CONFIG_LOADADDR 0x10800000
+#define CONFIG_SYS_TEXT_BASE 0x17800000
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
"mmcpart=2\0" \
"mmcroot=/dev/mmcblk0p3 rootwait rw\0" \
"mmcargs=setenv bootargs console=${console},${baudrate} " \
- "root=${mmcroot}\0" \
+ "root=${mmcroot}\0" \
"loadbootscript=" \
- "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
- "source\0" \
+ "source\0" \
"loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
"mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "bootm\0" \
+ "run mmcargs; " \
+ "bootm\0" \
"netargs=setenv bootargs console=${console},${baudrate} " \
- "root=/dev/nfs " \
- "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"netboot=echo Booting from net ...; " \
- "run netargs; " \
- "dhcp ${uimage}; bootm\0" \
+ "run netargs; " \
+ "dhcp ${uimage}; bootm\0" \
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev};" \
"if mmc rescan ${mmcdev}; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loaduimage; then " \
- "run mmcboot; " \
- "else run netboot; " \
- "fi; " \
- "fi; " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
"else run netboot; fi"
#define CONFIG_ARP_TIMEOUT 200UL
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#define CONFIG_SYS_PROMPT "MX6QSABRELITE U-Boot > "
+#define CONFIG_SYS_PROMPT "MX6QSABRELITE U-Boot > "
#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_CBSIZE 256
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_MEMTEST_START 0x10000000
-#define CONFIG_SYS_MEMTEST_END 0x10010000
+#define CONFIG_SYS_MEMTEST_END 0x10010000
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_SYS_HZ 1000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_SYS_HZ 1000
#define CONFIG_CMDLINE_EDITING
-#define CONFIG_STACKSIZE (128 * 1024)
+#define CONFIG_STACKSIZE (128 * 1024)
/* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
-#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_CMD_CACHE
#endif
-#endif /* __CONFIG_H */
+#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / commitdiff