Stefan Roese [Fri, 5 Jan 2007 10:46:05 +0000 (11:46 +0100)]
[PATCH] nand: Fix problem with oobsize calculation
Here the description from Brian Brelsford <Brian_Brelsford@dell.com>:
The Hynix part returns a 0x1d in the 4th ID byte. The Samsung part
returns a 0x15. In the code fragment below bits [1:0] determine the
page size, it is ANDed via "(extid & 0x3)" then shifted out. The
next field is also ANDed with 0x3. However this is a one bit field
as defined in the Hynix and Samsung parts in the 4th ID byte that
determins the oobsize, not a two bit field. It works on Samsung as
bits[3:2] are 01. However for the Hynix there is a 11 in these two
bits, so the oob size gets messed up.
I checked the correct linux code and the suggested fix from Brian is
also available in the linux nand mtd driver.
Bartlomiej Sieka [Thu, 28 Dec 2006 18:08:21 +0000 (19:08 +0100)]
Few V38B changes:
- fix a typo in V38B config file
- move watchdog initialisation earlier in the boot process
- add "wdt=off" to default kernel command line (disables kernel watchdog)
Stefan Roese [Wed, 29 Nov 2006 14:42:37 +0000 (15:42 +0100)]
[PATCH] Add support for Prodrive P3M750 & P3M7448 (P3Mx) boards
This patch adds support for the Prodrive P3M750 (PPC750 & MV64460)
and the P3M7448 (MPC7448 & MV64460) PMC modules. Both modules are
quite similar and share the same board directory "prodrive/p3mx"
and the same config file "p3mx.h".
Stefan Roese [Wed, 29 Nov 2006 11:53:15 +0000 (12:53 +0100)]
[PATCH] common/cmd_elf.c: Enable loadaddr as parameter in bootvx command
In the bootvx command the load address was only read from the env
variable "loadaddr" and not optionally passed as paramter as described
in the help. This is fixed with this patch. The behaviour is now the
same as in the bootelf command.
Stefan Roese [Mon, 27 Nov 2006 16:34:10 +0000 (17:34 +0100)]
[PATCH] Select NAND embedded environment from board configuration
The current NAND Bootloader setup forces the environment
variables to be in line with the bootloader. This change
enables the configuration to be made in the board include
file instead so that it can be individually enabled.
Signed-off-by: Nick Spence <nick.spence@freescale.com> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Mon, 27 Nov 2006 16:04:06 +0000 (17:04 +0100)]
[PATCH] Allow CONFIG_OF_FLAT_TREE to boot a non-arch/powerpc kernel
This patch allows an arch/ppc kernel to be booted by just passing 1 or 2
arguments to bootm. It removes the getenv("disable_of") test that used
to be used for this purpose.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Jon Loeliger <jdl@freescale.com>
Stefan Roese [Mon, 13 Nov 2006 12:55:24 +0000 (13:55 +0100)]
[PATCH] CFI driver AMD Command Set Top boot geometry reversal, etc. [Updated]
* Adds support for AMD command set Top Boot flash geometry reversal
* Adds support for reading JEDEC Manufacturer ID and Device ID
* Adds support for displaying command set, manufacturer id and
device ids (flinfo)
* Makes flinfo output to be consistent when CFG_FLASH_EMPTY_INFO defined
* Removes outdated change history (refer to git log instead)
Signed-off-by: Tolunay Orkun <listmember@orkun.us> Signed-off-by: Stefan Roese <sr@denx.de>
Bartlomiej Sieka [Sat, 11 Nov 2006 21:43:00 +0000 (22:43 +0100)]
Change the GPIO pin multiplexing configuration for V38B. The USB GPIO pin
group is enabled for USB earlier (in cpu_init_f() instead of
usb_lowlevel_init()).
Timur Tabi [Sat, 4 Nov 2006 01:15:00 +0000 (19:15 -0600)]
mpc83xx: Update 83xx to use fsl_i2c.c
Update the 83xx tree to use I2C support in drivers/fsl_i2c.c. Delete
cpu/mpc83xx/i2c.c, include/asm-ppc/i2c.h, and all references to those files.
Added multiple I2C bus support to fsl_i2c.c.
Dave Liu [Fri, 3 Nov 2006 00:05:50 +0000 (18:05 -0600)]
mpc83xx: Fix the incorrect dcbz operation
The 834x rev1.x silicon has one CPU5 errata.
The issue is when the data cache locked with
HID0[DLOCK], the dcbz instruction looks like no-op inst.
The right behavior of the data cache is when the data cache
Locked with HID0[DLOCK], the dcbz instruction allocates
new tags in cache.
The 834x rev3.0 and later and 8360 have not this bug inside.
So, when 834x rev3.0/8360 are working with ECC, the dcbz
instruction will corrupt the stack in cache, the processor will
checkstop reset.
However, the 834x rev1.x can work with ECC with these code,
because the sillicon has this cache bug. The dcbz will not
corrupt the stack in cache.
Really, it is the fault code running on fault sillicon.
This patch fix the incorrect dcbz operation. Instead of
CPU FP writing to initialise the ECC.
CHANGELOG:
* Fix the incorrect dcbz operation instead of CPU FP
writing to initialise the ECC memory. Otherwise, it
will corrupt the stack in cache, The processor will checkstop
reset.
* For the 8349E-mITX, fix some size values in pci_init_board(), enable
the clock for the 2nd USB board (Linux kernel will hang otherwise),
and fix the CONFIG_BOOTARGS macro.
Timur Tabi [Wed, 1 Nov 2006 00:44:42 +0000 (18:44 -0600)]
mpc83xx: Add support for the MPC8349E-mITX
PREREQUISITE PATCHES:
* This patch can only be applied after the following patches have been applied:
1) DNX#2006090742000024 "Add support for multiple I2C buses"
2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x"
3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c"
4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems"
5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems"
CHANGELOG:
* Add support for the Freescale MPC8349E-mITX reference design platform.
The second TSEC (Vitesse 7385 switch) is not supported at this time.
Ben Warren [Thu, 7 Sep 2006 20:51:04 +0000 (16:51 -0400)]
Multi-bus I2C implementation of MPC834x
Hello,
Attached is a patch implementing multiple I2C buses on the MPC834x CPU
family and the MPC8349EMDS board in particular.
This patch requires Patch 1 (Add support for multiple I2C buses).
Testing was performed on a 533MHz board.
Signed-off-by: Ben Warren <bwarren@qstreams.com>
CHANGELOG:
Implemented driver-level code to support two I2C buses on the
MPC834x CPU family and the MPC8349EMDS board. Available I2C bus speeds
are 50kHz, 100kHz and 400kHz on each bus.
Ben Warren [Thu, 7 Sep 2006 20:50:54 +0000 (16:50 -0400)]
Add support for multiple I2C buses
Hello,
Attached is a patch providing support for multiple I2C buses at the
command level. The second part of the patch includes an implementation
for the MPC834x CPU and MPC8349EMDS board.
Signed-off-by: Ben Warren <bwarren@qstreams.com>
Overview:
1. Include new 'i2c' command (based on USB implementation) using
CONFIG_I2C_CMD_TREE.
2. Allow multiple buses by defining CONFIG_I2C_MULTI_BUS. Note that
the commands to change bus number and speed are only available under the
new 'i2c' command mentioned in the first bullet.
3. The option CFG_I2C_NOPROBES has been expanded to work in multi-bus
systems. When CONFIG_I2C_MULTI_BUS is used, this option takes the form
of an array of bus-device pairs. Otherwise, it is an array of uchar.
CHANGELOG:
Added new 'i2c' master command for all I2C interaction. This is
conditionally compiled with CONFIG_I2C_CMD_TREE. New commands added for
setting I2C bus speed as well as changing the active bus if the board
has more than one (conditionally compiled with
CONFIG_I2C_MULTI_BUS). Updated NOPROBE logic to handle multiple buses.
Updated README.
Timur Tabi [Wed, 1 Nov 2006 00:13:36 +0000 (18:13 -0600)]
mpc83xx: Add support for Errata DDR6 on MPC 834x systems
CHANGELOG:
* Errata DDR6, which affects all current MPC 834x processors, lists changes
required to maintain compatibility with various types of DDR memory. This
patch implements those changes.
Nick Spence [Sat, 30 Sep 2006 07:32:59 +0000 (00:32 -0700)]
NAND Flash verify across block boundaries
This patch addresses a problem when CONFIG_MTD_NAND_VERIFY_WRITE is
defined
and the write crosses a block boundary. The pointer to the verification
buffer (bufstart) is not being updated to reflect the starting of the
new
block so the verification of the second block fails.
CHANGELOG:
* Fix NAND FLASH page verification across block boundaries
- Fix issues related to the use of ELDK 4 when compiling for MarelV38B:
* remove warnings when compiling ethaddr.c
* adjust linker script (fixes a crash resulting from incorrect
definition of __u_boot_cmd_start)
- Some MarelV38B code cleanup.
- Add MPC5XXX register definition MPC5XXX_WU_GPIO_DATA_I and change the
MPC5XXX_WU_GPIO_DATA macro to MPC5XXX_WU_GPIO_DATA_O (per MPC5200 User's
Manual). Replace the uses of MPC5XXX_WU_GPIO_DATA with
MPC5XXX_WU_GPIO_DATA_O for affected boards.
projects / karo-tx-uboot.git / log