Thierry Reding [Fri, 20 Mar 2015 12:24:22 +0000 (13:24 +0100)]
ARM: tegra: Make pinmux.h standalone includible
This header file uses type definitions (u8, u32) from linux/types.h but
doesn't include it. If includes aren't carefully ordered this can cause
build failures.
Cc: Tom Warren <twarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Wed, 5 Aug 2015 22:47:12 +0000 (00:47 +0200)]
apalis/colibri_t30: fix usb dm regression
Unfortunately currently both Apalis T30 as well as Colibri T30 crash
upon starting USB host support. This is due to the following patch not
having taken into account that our T30 device trees were defaulting to
peripheral only mode instead of otg:
Marcel Ziswiler [Wed, 5 Aug 2015 22:47:11 +0000 (00:47 +0200)]
colibri_t20: fix reset out pin
Make sure SODIMM pin 87 nRESET_OUT is released properly by explicitly
setting its pin mux function to GMI. This solves some issues with e.g.
USB not being fully operational on carrier boards with USB hubs
connected to reset if U-Boot got loaded via recovery mode aka rcm.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Wed, 5 Aug 2015 22:47:10 +0000 (00:47 +0200)]
apalis/colibri_t20/30: clean-up
Various clean-ups either in comments, order or spacing without any
functional impact:
- Add some comments in the device trees resp. reorder some parameters
for consistency across all our modules.
- Sort some include files alphabetically (while leaving common.h on
top of course).
- Streamline some comments in the configuration files and fix the
spacing from using spaces to tabs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Wed, 5 Aug 2015 22:47:05 +0000 (00:47 +0200)]
tegra: nand: fix read_byte required for proper onfi detection
Fix PIO read_byte() implementation not only used for the legacy READ ID
but also the PARAM command required for proper ONFI detection.
This fix is inspired by Lucas Stach's Linux Tegra NAND driver of late
(not mainline yet but getting there soon I hope).
I vaguely remember that those commands are special on 16-bit bus NAND
(e.g. always return 8-bit data regardless) and later Linux MTD fixed/
changed the way this is handled which in turn broke once U-Boot pulled
that in. Basically instead of doing PIO read regular DMA block read is
now used which this patch actually fixes.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Marcel Ziswiler [Wed, 5 Aug 2015 22:47:04 +0000 (00:47 +0200)]
colibri_t20: disable PMIC sleep mode on low supply voltage
The Colibri T20's PMIC enters a sleep mode on low supply voltage < 3.0V
±2.5% (2.92...3.08V). Rising the main supply voltage again does not
bring it back to regular operation. Not even a full reset does bring
the module back. A full power cycle was required to reboot the system.
A long positive pulse on the PMICs resume pin also reboots the system
but this pin is only accessible as a test point on the module.
This patch configures the PMIC through I2C to not enter this sleep mode
plus force it to normal state upon sleep request exit should this ever
happen.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stefan Agner [Wed, 5 Aug 2015 15:17:01 +0000 (17:17 +0200)]
logos: add Toradex logo
Use the boot loader splash screen from WinCE which matches our
wallpapers position wise. Although the logo is an 8-bit indexed BMP as
well colours looked odd at first in U-Boot. After converting to full
RGB palette and converting back to an indexed BMP using imagemagick
the Logo showed up properly.
This fixes the following warning (and the runtime error reporting):
../common/image-fdt.c:491:4: warning: 'fdt_ret' may be used
uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Simon Glass <sjg@chromium.org>
Marcel Ziswiler [Wed, 5 Aug 2015 15:17:00 +0000 (17:17 +0200)]
generic-board: allow showing custom board info
Allow showing custom board info from a checkboard() function being
implemented if CONFIG_CUSTOM_BOARDINFO is specified. Previously the
device tree model was always displayed not taking any
CONFIG_CUSTOM_BOARDINFO into account.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Simon Glass <sjg@chromium.org>
fs/fs.c: read up to EOF when len would read past EOF
http://lists.denx.de/pipermail/u-boot/2012-September/134347.html
allows for reading files in chunks from the shell.
When this feature is used to read past the end of a file an error
was returned instead of returning the bytes read up to the end of
file. Thus the following fails in the shell:
offset = 0
len = chunksize
do
read file, offset, len
write data
until bytes_read < len
The patch changes the behaviour to printing an informational
message and returning the actual read number of bytes aka read(2)
behaviour for convenient use in U-Boot scripts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Marcel Ziswiler [Tue, 4 Aug 2015 13:49:50 +0000 (15:49 +0200)]
common/lcd_console: fix console/logo regression
The following commit changed the order of the column vs. row parameter
to the lcd_init_console() function but missed actually changing it as
well the second time it is called from lcd_clear() which resulted in a
garbled text console which this patch fixes.
Nikita Kiryanov [Mon, 3 Aug 2015 09:36:58 +0000 (12:36 +0300)]
kconfig: add config option for shell prompt
Add option to set shell prompt string from menuconfig and migrate
boards globally.
The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
files. This results in a streamlined default value across platforms, and
includes the following files: spear-common, sunxi-common, mv-common,
ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
not updated in their respective defconfig files under the assumption that
since they did not explicitly define a value, they're fine with whatever
the default is.
- On the other hand, boards that relied on a value defined in some
<boards>_common.h file such as woodburn_common, rpi-common,
bur_am335x_common, ls2085a_common, siemens_am33x_common, and
omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
assigning a value for CONFIG_SYS_PROMPT.
Cc: Tom Rini <trini@konsulko.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion] Signed-off-by: Tom Rini <trini@konsulko.com>
Masahiro Yamada [Sat, 1 Aug 2015 07:39:13 +0000 (16:39 +0900)]
ARM: drop "optional" from target select in favor of ARCH_VERSATILE
Since commit a26cd04920dc ("arch: Make board selection choices
optional"), Kconfig could create such an insane .config file that
no SoC/board is selected.
This is now a real problem for Buildroot, for example.
(http://lists.busybox.net/pipermail/buildroot/2015-July/135125.html)
This commit drops the "optional" from the ARM target select menu
in favor of "Versatile family".
Rationale:
- Historically, Linux chose versatile_defconfig as the default
of ARM defconfig. (arch/arm/Makefile of Linux describes:
KBUILD_DEFCONFIG := versatile_defconfig)
Tom Rini [Fri, 31 Jul 2015 23:55:10 +0000 (19:55 -0400)]
ARM: SPL: Use CONFIG_SPL_DM not CONFIG_DM
We now have the CONFIG_SPL_DM for code within SPL to toggle caring about
DM or not. Without this change platforms that do enable CONFIG_DM but
not CONFIG_SPL_DM may be broken (such as OMAP5).
Cc: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 31 Jul 2015 23:55:09 +0000 (19:55 -0400)]
gpio: omap: Drop 'method' parameter
The "method" parameter was part of the original port of the driver from
the kernel. At some point this may have been added to allow for future
differentiation (as omap1 and omap2 have different GPIO IP blocks, so
this wasn't an unreasonable thing to do). At this point however it's
just extra overhead, so drop.
- Re-sync DT files for am33xx with Linux Kernel v4.1
- Include DT file now for the "AM335x GP EVM" and build target for it,
via device tree and DM.
- We only need to provide platform data for UART when OF_CONTROL isn't
also enabled really. We can just push GPIO to coming from DT
Peter Griffin [Thu, 30 Jul 2015 17:55:23 +0000 (18:55 +0100)]
ARM64: hikey: hi6220: Add u-boot support for the 96boards CE HiKey board.
HiKey is the first 96boards consumer edition compliant board. It features a hi6220
SoC which has eight ARM A53 cpu's.
This initial port adds support for: -
1) Serial
2) eMMC / SD card
3) USB
4) GPIO
It has been tested with Arm Trusted Firmware running u-boot as the BL33 executable.
Notes:
eMMC has been tested with basic reading of eMMC partition into DDR. I have not
tested writing / erasing. Due to lack of clock control it won't be
running in the most performant high speed mode.
SD card slot has been tested for reading and booting kernels into DDR.
It is also currently configured to save the u-boot environment to the
SD card.
USB has been tested with ASIX networking adapter to tftpboot kernels
into DDR. On v2015.07-rc2 dhcp now works, and also USB mass storage
are correctly enumerated.
GPIO has been tested using gpio toggle GPIO4_1-3 to flash the LEDs.
Basic SoC datasheet can be found here: -
https://github.com/96boards/documentation/blob/master/hikey/
Hi6220V100_Multi-Mode_Application_Processor_Function_Description.pdf
Board schematic can be found here: -
https://github.com/96boards/documentation/blob/master/hikey/
96Boards-Hikey-Rev-A1.pdf
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Peter Griffin [Thu, 30 Jul 2015 17:55:22 +0000 (18:55 +0100)]
mmc: hi6220_dw_mmc: Add hi6220 glue code for dw_mmc controller.
This patch adds the glue code for hi6220 SoC which has 2x synopsis
dw_mmc controllers. This will be used by the hikey board support
in subsequent patches.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Peter Griffin [Thu, 30 Jul 2015 17:55:21 +0000 (18:55 +0100)]
pmic: pmic_hi6553: Add a driver for the hi6553 pmic found on hikey board.
This adds a simple pmic driver for the hi6553 pmic which is used in
conjunction with the hi6220 SoC on the hikey board. Eventually this
driver will be updated to be a proper UCLASS PMIC driver which
can parse the voltages direct from device tree.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Gong Qianyu [Thu, 30 Jul 2015 06:00:01 +0000 (14:00 +0800)]
common/cmd_source.c: Fix the source command failure under 64-bit platform
Modify the data pointer type from ulong* to u32*.
For arm64 type "ulong" could be 64-bit. Then in line 89 of common/cmd_source.c:
"while (*data++);" data will point to the next 64 bits each time. As the uImage
file generated by mkimage tool keeps the same data format in either 32-bit or 64-bit
platform, the difference would cause failure in 64-bit platform.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Register Base addresses are same for PLLs in all
keystone platforms. If a PLL is not available, the corresponding
register addresses are marked as reserved.
Hence use a common definition.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There are two types of PLL for all keystone platforms:
Main PLL, Secondary PLL. Instead of duplicating the same definition
for each secondary PLL, have a common function which does
initialization for both PLLs. And also add proper register
definitions.
Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DRA72x processor variants are single core and it does not export ACP[1].
Hence, we have no source for generating an external snoop requests which
appear to be key to the deadlock in DRA72x design.
Since we build the same image for DRA74x and DRA72x platforms, lets
runtime detect and disable the workaround (in favor of performance) on
DRA72x platforms.
Add workaround for Cortex-A15 ARM erratum 801819 which says in summary
that "A livelock can occur in the L2 cache arbitration that might
prevent a snoop from completing. Under certain conditions this can
cause the system to deadlock. "
Recommended workaround is as follows:
Do both of the following:
1) Do not use the write-back no-allocate memory type.
2) Do not issue write-back cacheable stores at any time when the cache
is disabled (SCTLR.C=0) and the MMU is enabled (SCTLR.M=1). Because it
is implementation defined whether cacheable stores update the cache when
the cache is disabled it is not expected that any portable code will
execute cacheable stores when the cache is disabled.
For implementations of Cortex-A15 configured without the “L2 arbitration
register slice” option (typically one or two core systems), you must
also do the following:
3) Disable write-streaming in each CPU by setting ACTLR[28:25] = 0b1111
So, we provide an option to disable write streaming on OMAP5 and DRA7.
It is a rare condition to occur and may be enabled selectively based
on platform acceptance of risk.
Applies to: A15 revisions r2p0, r2p1, r2p2, r2p3 or r2p4 and REVIDR[3]
is set to 0.
Note: certain unicore SoCs *might* not have REVIDR[3] not set, but
might not meet the condition for the erratum to occur when they donot
have ACP (Accelerator Coherency Port) hooked to ACE (AXI Coherency
Extensions). Such SoCs will need the work around handled in the SoC
specific manner, since there is no ARM generic manner to detect such
configurations.
Based on ARM errata Document revision 18.0 (22 Nov 2013)
ARM: cache: implement a default weak flush_cache() function
Current many cpu use the same flush_cache() function, which just call
the flush_dcache_range().
So implement a weak flush_cache() for all the cpus to use.
In original weak flush_cache() in arch/arm/lib/cache.c, there has some
code for ARM1136 & ARM926ejs. But in the arch/arm/cpu/arm1136/cpu.c and
arch/arm/cpu/arm926ejs/cache.c, there implements a real flush_cache()
function as well. That means the original code for ARM1136 & ARM926ejs
in weak flush_cache() of arch/arm/lib/cache.c is totally useless.
So in this patch remove such code in flush_cache() and only call
flush_dcache_range().
ARM: cache: add an empty stub function for invalidate/flush dcache
Since some driver like ohci, lcd used dcache functions. But some ARM
cpu don't implement the invalidate_dcache_range()/flush_dcache_range()
functions.
To avoid compiling errors this patch adds an weak empty stub function
for all ARM cpu in arch/arm/lib/cache.c.
And ARM cpu still can implemnt its own cache functions on the cpu folder.
Signed-off-by: Josh Wu <josh.wu@atmel.com> Reviewed-by: York Sun <yorksun@freescale.com>
Correct License and Copyright information on few files
gpio.h - Added missing copyright in few files.
rsa-mod-exp.h - Corrected copyright in the file.
fsl_sec.h - Added missing license in files
drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license
The menuconfig for drivers are getting more and more cluttered
and unreadable because too many entries are displayed in a single
flat menu. Use hierarchic menu for each category.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Update to apply again in a few places, drop USB hunk] Signed-off-by: Tom Rini <trini@konsulko.com>
Alexander Stein [Fri, 24 Jul 2015 07:22:15 +0000 (09:22 +0200)]
arm/rpi: Enable dcache
Now that mailbox driver supports cache flush and invalidation, we can
enable dcache.
Signed-off-by: Alexander Stein <alexanders83@web.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Alexander Stein [Fri, 24 Jul 2015 07:22:14 +0000 (09:22 +0200)]
dwc2: Add dcache support
This adds dcache support for dwc2. The DMA buffers must be DMA aligned and
is flushed for outgoing transactions before starting transfer. For
ingoing transactions it is invalidated after the transfer has finished.
Signed-off-by: Alexander Stein <alexanders83@web.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[trini: Update to apply again on top of DM patches] Signed-off-by: Tom Rini <trini@konsulko.com>
Alexander Stein [Fri, 24 Jul 2015 07:22:13 +0000 (09:22 +0200)]
arm/mach-bcm283x/mbox: Flush and invalidate dcache when using fw mailbox
When using dcache the setup data for the mailbox must be actually written
into memory before calling into firmware. Thus flush and invalidate the
memory.
Signed-off-by: Alexander Stein <alexanders83@web.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Alexander Stein [Fri, 24 Jul 2015 07:22:12 +0000 (09:22 +0200)]
ARM: bcm283x: Allocate all mailbox buffers cacheline aligned
The mailbox buffer is required to be at least 16 bytes aligned, but for
cache invalidation and/or flush it needs to be cacheline aligned.
Use ALLOC_CACHE_ALIGN_BUFFER for all mailbox buffer allocations.
Signed-off-by: Alexander Stein <alexanders83@web.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Alexander Stein [Fri, 24 Jul 2015 07:22:11 +0000 (09:22 +0200)]
ARM: bcm283x: Define CONFIG_SYS_CACHELINE_SIZE
The cacheline is always 32 bytes for arm1176 CPUs, so define it at board
config level for cache handling code.
The ARM Cortex-A7 has a dcache line size of 64 bytes.
Signed-off-by: Alexander Stein <alexanders83@web.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Alexander Stein [Fri, 24 Jul 2015 07:22:10 +0000 (09:22 +0200)]
arm1136/arm1176: Merge cache handling code
As both cores are similar merge the cache handling code for both CPUs
to arm11 directory.
Signed-off-by: Alexander Stein <alexanders83@web.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Stephen Warren <swarren@wwwdotorg.org>
[trini: Add hunk to arch/arm/cpu/arm1136/Makefile] Signed-off-by: Tom Rini <trini@konsulko.com>
Alexander Stein [Fri, 24 Jul 2015 07:22:09 +0000 (09:22 +0200)]
arm1136: Remove dead code
Apparently lcd_panel_disable is not defined anywhere, so no config for
an arm1136 board would have set CONFIG_LCD. Remove the unused code.
Signed-off-by: Alexander Stein <alexanders83@web.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Stephen Warren <swarren@wwwdotorg.org>
sniper: Keypad support, with recovery and fastboot key combinations
Using the twl4030 keypad allows booting directly into some special boot modes,
such as recovery or fastboot. the VOL+ key will trigger a boot to recovery while
the VOL- key will trigger a boot to fastboot.
The G (gesture) key remains unused at this point.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
sniper: Power off when the power on reason is not a valid one
In most cases, userspace will attempt to power off the device with HALT instead
of POWER_OFF, which triggers a reset instead of a proper power off from the
TWL4030. Hence, it is up to the bootloader to actually turn the device off when
there is no reason to turn it on.
A reboot identified with the OMAP reboot mode bits set is acceptable, as well as
a power on reason from either the power button, USB or charger plug.
Other cases should trigger a power off. Note that for the U-Boot reset command
to take effect, we have to fill-in the OMAP reboot bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for the fastboot USB gadget, including flashing to the
internal MMC and reboot to bootloader or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Update to use Kconfig for MUSB] Signed-off-by: Tom Rini <trini@konsulko.com>
Now that the serial number is correctly defined, we can pass it to the kernel
using the (legacy) ATAG method. It will be automatically passed via device-tree
when enabled.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
sniper: Serial number support, obtained from die ID
The OMAP3 has some die-specific ID bits that we can use to give the device a
(more or less) unique serial number. This is particularly useful for e.g. USB.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This adds support for the omap3 reboot mode mechanism and exports the reboot
mode via an environment variable, that is used in the boot command to make it
possible to boot from the recovery partition.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
The LG Optimus Black (P970) codename sniper is a smartphone that was designed
and manufactured by LG Electronics (LGE) and released back in 2011.
It is using an OMAP3630 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up. This port is aimed at running an Android version
such as Replicant, the fully free Android distribution. However, support for
upstream Linux with device-tree and common GNU/Linux distros boot commands
could be added in the future.
For more information about the journey to freeing this device, please read the
series of blog posts at:
http://code.paulk.fr/article20/a-hacker-s-journey-freeing-a-phone-from-the-ground-up-first-part
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add CONFIG_OF_SUPPORT] Signed-off-by: Tom Rini <trini@konsulko.com>
Reboot mode is written in scratchpad memory before reboot in the form of a
single char, that is the first letter of the reboot mode string as passed to the
reboot function.
This mechanism is supported on OMAP3 both my the upstream kernel and by various
TI kernels.
It is up to each board to make use of this mechanism or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
input: TWL4030 input support for power button, USB and charger
This adds support for detecting a few inputs exported by the TWL4030.
Currently-supported inputs are the power button, USB and charger presence. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This adds support for powering off (the omap3 SoC) from the twl4030. This is
especially useful when the kernel does not actually power off the device using
this method but reboots and leaves it up to the bootloader to actually turn the
power off. Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The change adds SPL build support to Timll DevKit3250 board, the
generated SPL image can be uploaded over UART5, JTAG or stored on
NAND. SPL is designed to load U-boot image from NAND.
All new NAND chip defines in board configuration are needed by
SPL NAND "simple" framework, the framework is used to reduce
potentially duplicated code from LPC32xx SLC NAND driver.
lpc32xx: devkit3250: update of board configuration
This change adds more peripherals to Timll DevKit3250 board, namely
MAC and SMSC phy, SLC NAND, GPIO, SPI and I2C.
Also the default serial console is changed to UART5, added an option
to pass device tree blob by means of bootm, predefined environment
variables are slightly extended and reserved space on NAND to store
user defined U-boot environment.
The change adds support of LPC32xx SLC NAND controller.
LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.
This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.
Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.
The driver can be included to an SPL image.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Scott Wood <scottwood@freescale.com> Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
spl: nand: simple: replace readb() with chip specific read_buf()
Some NAND controllers define custom functions to read data out,
respect this in order to correctly support bad block handling in
simple SPL NAND framework.
NAND controller specific read_buf() is used even to read 1 byte in
case of connected 8-bit NAND device, it turns out that read_byte()
may become outdated.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Tom Rini <trini@konsulko.com> Cc: Tom Warren <twarren@nvidia.com> Acked-by: Scott Wood <scottwood@freescale.com>
Rob Herring [Fri, 17 Jul 2015 15:57:17 +0000 (10:57 -0500)]
image: fix Android ramdisk support when dtb is specified
If a dtb is specified on the command-line, the Android boot image ramdisk
will not be found. Fix this so that we can specify the ramdisk address and
dtb address. The syntax is to enter the Android boot image address for
both the kernel and ramdisk.
Mark Tomlinson [Wed, 1 Jul 2015 04:38:29 +0000 (16:38 +1200)]
JFFS2: Use merge sort when parsing filesystem
When building the file system the existing code does an insertion into
a linked list. It attempts to speed this up by keeping a pointer to
where the last entry was inserted but it's still slow.
Now the nodes are just inserted into the list without searching
through for the correct place. This unsorted list is then sorted once
using mergesort after all the entries have been added to the list.
This speeds up the scanning of the flash file system considerably.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Mark Tomlinson [Wed, 1 Jul 2015 04:38:28 +0000 (16:38 +1200)]
JFFS2: Use CLEANMARKER to reduce scanning time
If a sector has a CLEANMARKER at the beginning, it indicates that the
entire sector has been erased. Therefore, if this is found, we can skip the
entire block. This was not being done before this patch.
The code now does the same as the kernel does when encountering a
CLEANMARKER. It still checks that the next few words are FFFFFFFF, and if
so, the block is assumed to be empty, and so is skipped.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
projects / karo-tx-uboot.git / log