-* Patch by Rune Torgersen, 23 May 2003:
- Update for MPC8266ADS board
-
-* Get (mostly) rid of CFG_MONITOR_LEN definition; compute real length
- instead CFG_MONITOR_LEN is now only used to determine _at_compile_
- _time_ (!) if the environment is embedded within the U-Boot image,
- or in a separate flash sector.
-
-* Cleanup CFG_DER #defines in config files (wd maintained only)
-
-* Fix data abort exception handling for arm920t CPU
-
-* Fix alignment problems with flash driver for TRAB board
-
-* Patch by Donald White, 21 May 2003:
- fix calculation of base address in pci_hose_config_device()
-
-* Fix bug in command line parsing: "cmd1;cmd2" is supposed to always
- execute "cmd2", even if "cmd1" fails. Note that this is different
- to "run var1 var2" where the contents of "var2" will NOT be
- executed when a command in "var1" fails.
-
-* Add zero-copy ramdisk support (requires corresponding kernel support!)
-
-* Patch by Kyle Harris, 20 May 2003:
- In preparation for an ixp port, rename cpu/xscale and arch-xscale
- into cpu/pxa and arch-pxa.
-
-* Patch by Stefan Roese, 23 May 2003:
- - IBM PPC405EP port added.
- - CONFIG_UART1_CONSOLE added. If defined internal UART1 (and not
- UART0) is used as default U-Boot console. PPC4xx only!
- - esd ASH405 board added (PPC405EP based).
- - BUBINGA405EP board added (PPC405EP based - IBM Eval Board).
- - esd CPCI405AB board added.
- - esd PMC405 board added.
- - Update of some esd boards.
-
-* Patch by Denis Peter, 19 Mai 2003:
- add support for the MIP405-3 board
-
-* Patch by Dave Ellis, 22 May 2003:
- Fix problem with only partially cleared .bss segment
-
-* Patch by Rune Torgersen, 12 May 2003:
- get PCI to work on a MPC8266ADS board; incorporate change to
- cpu/mpc8260/pci.c to enable overrides of PCI memory parameters
-
-* Patch by Nye Liu, 1 May 2003:
- minor patches for the FADS8xx
-
-* Patch by Thomas Schäfer, 28 Apr 2003:
- Fix SPD handling for 256 ECC DIMM on Walnut
-
-* Add support for arbitrary bitmaps for TRAB's VFD command;
- allow to pass boot bitmap addresses in environment variables;
- allow for zero boot delay
-
-* Patch by Christian Geißinger, 19 May 2002:
- On TRAB: wait until the dummy byte has been completely sent
-
-* Patch by David Updegraff, 22 Apr 2003:
- update for CrayL1 board
-
-* Patch by Pantelis Antoniou, 21 Apr 2003:
- add boot support for ARTOS (a proprietary OS)
-
-* Patch by Steven Scholz, 11 Apr 2003:
- Add support for RTC DS1338
-
-* Patch by Rod Boyce, 24 Jan 2003:
- Fix counting of extended partitions in diskboot command
-
-* Patch by Christophe Lindheimer, 20 May 2003:
- allow the use of CFG_LOADS when CFG_NO_FLASH is set
-
-* Fix SDRAM timing on Purple board
-
-* Add support for CompactFlash on ATC board
- (includes support for Intel 82365 and compatible PC Card controllers,
- and Yenta-compatible PCI-to-CardBus controllers)
-
-* Patch by Mathijs Haarman, 08 May 2003:
- Add lan91c96 driver (tested on Lubbock and custom PXA250 board only)
-
-* Fix problem with usage of "true" (undefined in current versions of bfd.h)
-
-* Add support for Promess ATC board
-
-* Patch by Keith Outwater, 28 Apr 2003:
- - Miscellaneous corrections and additions to GEN860T board specific code.
- - Added GEN860_SC variant to GEN860T.
- - Miscellaneous corrections to GEN860T documentation.
- - Correct duplicate entry in U-Boot CREDITS file.
- - Add GEN860T_SC entry in MAINTAINERS file.
- - Update CREDITS file with GEN860T_SC info.
-
-* Update Smiths Aerospace addresses in MAINTAINERS file
-
-* Fix error handling in hush's version of "run" command
-
-* LWMON extensions:
- - Splashscreen support
- - modem support
- - sysmon support
- - temperature dependend enabling of LCD
-
-* Allow booting from old "PPCBoot" disk partitions
-
-* Add support for TQM8255 Board / MPC8255 CPU
-
-======================================================================
-Changes for U-Boot 0.3.1:
-======================================================================
-
-* Make sure Block Lock Bits get cleared in R360MPI flash driver
-
-* MPC823 LCD driver: Fill color map backwards, to allow for steady
- display when Linux takes over
-
-* Patch by Erwin Rol, 27 Feb 2003:
- Add support for RTEMS (this time for real).
-
-* Add support for "bmp info" and "bmp display" commands to load
- bitmap images; this can be used (for example in a "preboot"
- command) to display a splash screen very quickly after poweron.
-
-* Add support for 133 MHz clock on INCA-IP board
-
-* Patch by Lutz Dennig, 10 Apr 2003:
- Update for R360MPI board
-
-* Add new meaning to "autostart" environment variable:
- If set to "no", a standalone image passed to the
- "bootm" command will be copied to the load address
- (and eventually uncompressed), but NOT be started.
- This can be used to load and uncompress arbitrary
- data.
-
-* Patch by Stefan Roese, 10 Apr 2003:
- Changed DHCP client to use IP address from server option field #54
- from the OFFER packet in the server option field #54 in the REQUEST
- packet. This fixes a problem using a Windows 2000 DHCP server,
- where the DHCP-server is not the TFTP-server.
-
-* Set max brightness for MN11236 displays on TRAB board
-
-* Add support for TQM862L modules
-
-======================================================================
-Changes for U-Boot 0.3.0:
-======================================================================
-
-* Patch by Arun Dharankar, 4 Apr 2003:
- Add IDMA example code (tested on 8260 only)
-
-* Add support for Purple Board (MIPS64 5Kc)
-
-* Add support for MIPS64 5Kc CPUs
-
-* Fix missing setting of "loadaddr" and "bootfile" on ARM and MIPS
-
-* Patch by Denis Peter, 04 Apr 2003:
- - update MIP405-4 board
-
-* Patch by Stefan Roese, 4 Apr 2003:
- - U-Boot version environment variable "ver" added
- (CONFIG_VERSION_VARIABLE).
- - Changed PPC405GPr version from A to B.
- - Changed CPCI405 to use CTS instead of DSR on PPC405 UART1.
-
-* Patches by Denis Peter, 03 April 2003:
- - fix PCI IRQs on MPL boards
- - fix two more un-relocated pointer problems
-
-* Fix behaviour of "run" command:
- - print error message iv variable does not exist
- - terminate processing of arguments in case of error
-
-* Patches by Peter Figuli, 10 Mar 2003
- - Add support for BTUART on PXA platform
- - Add support for WEP EP250 (PXA) board
-
-* Fix flash problems on INCA-IP; add tool to allow bruning images to
- flash using a BDI2000
-
-* Implement fix for I2C Edge Conditions problem for all boards that
- use the bit-banging driver (common/soft_i2c.c)
-
-* Patch by Martin Winistoerfer, 23 Mar 2003
- - Add port to MPC555/556 microcontrollers
- - Add support for cmi customer board with
- Intel 28F128J3A, 28F320J3A or 28F640J3A flash.
-
-* Patch by Rick Bronson, 28 Mar 2003:
- - fix common/cmd_nand.c
-
-* Patch by Arun Dharankar, 24 Mar 2003:
- - add threads / scheduler example code
-
-* Add patches by Robert Schwebel, 31 Mar 2003:
- - add ctrl-c support for kermit download
- - align bdinfo output on ARM
- - csb226 board: bring in sync with innokom/memsetup.S
- - csb226 board: fix MDREFR handling
- - misc doc fixes / extensions
- - innokom board: cleanup, MDREFR fix in memsetup.S, config update
- - add BOOT_PROGRESS to armlinux.c
-
-* Add CPU ID, version, and clock speed for INCA-IP
-
-* Patches by Dave Ellis, 18 Mar 2003 for SXNI855T board:
- - fix SRAM and SDRAM memory sizing
- - add status LED support
- - add MAC address for second (SCC1) ethernet port
-
-* Update default environment for TQM8260 board
-
-* Patch by Rick Bronson, 16 Mar 2003:
- - Add NAND flash support for reading, writing, and erasing NAND
- flash (certain forms of which are called SmartMedia).
- - Add support for Atmel AT91RM9200DK ARM920T based development kit.
-
-* Patches by Robert Schwebel, 19 Mar 2003:
- - use arm-linux-gcc as default compiler for ARM
- - fix i2c fixup code
- - fix missing baudrate setting
- - added $loadaddr / CFG_LOAD_ADDR support to loadb
- - moved "ignoring trailing characters" _before_ u-boot wants to
- print out diagnostics messages; removes bogus characters at the
- end of transmission
-
-* Patch by John Zhan, 18 Mar 2003:
- Add support for SinoVee Microsystems SC8xx boards
-
-* Patch by Rolf Offermanns, 21 Mar 2003:
- ported the dnp1110 related changes from the current armboot cvs to
- current u-boot cvs. smc91111 does not work. problem marked in
- smc91111.c, grep for "FIXME".
-
-* Patch by Brian Auld, 25 Mar 2003:
- Add support for STM flash chips on ebony board
-
-* Add PCI support for MPC8250 Boards (PM825 module)
-
-* Patch by Stefan Roese, 25 Mar 2003:
- - PCI405 update.
-
-* Patch by Stefan Roese, 20 Mar 2003:
- - CPCI4052 update (support for revision 3).
- - Set edge conditioning circuitry on PPC405GPr for compatibility
- to existing PPC405GP designs.
- - Clip udiv to 5 bits on PPC405 (serial.c).
-
-* Extend INCAIP board support:
- - add automatic RAM size detection
- - add "bdinfo" command
- - pass flash address and size to Linux kernel
- - switch to 150 MHz clock
-
-* Avoid flicker on the TRAB's VFD by synchronizing the enable with
- the HSYNC/VSYNC. Requires new CPLD code (Version 101 for Rev. 100
- boards, version 153 for Rev. 200 boards).
-
-* Patch by Vladimir Gurevich, 12 Mar 2003:
- Fix relocation problem of statically initialized string pointers
- in common/cmd_pci.c
-
-* Patch by Kai-Uwe Blöm, 12 Mar 2003:
- Cleanup & bug fixes for JFFS2 code:
- - the memory mangement was broken. It caused havoc on malloc by
- writing beyond the block boundaries.
- - the length calculation for files was wrong, sometimes resulting
- in short file reads.
- - data copying now optionally takes fragment version numbers into
- account, to avoid copying from older data.
- See doc/README.JFFS2 for details.
-
-* Patch by Josef Wagner, 12 Mar 2003:
- - 16/32 MB and 50/80 MHz support with auto-detection for IP860
- - ETH05 and BEDBUG support for CU824
- - added support for MicroSys CPC45
- - new BOOTROM/FLASH0 and DOC base for PM826
-
-* Patch by Robert Schwebel, 12 Mar 2003:
- Fix the chpart command on innokom board
-
-* Name cleanup:
- mv include/asm-i386/ppcboot-i386.h include/asm-i386/u-boot-i386.h
- s/PPCBoot/U-Boot/ in some files
- s/pImage/uImage/ in some files
-
-* Patch by Detlev Zundel, 15 Jan 2003:
- Fix '' command line quoting
-
-* Patch by The LEOX team, 19 Jan 2003:
- - add support for the ELPT860 board
- - add support for Dallas ds164x RTC
-
-* Patches by David Müller, 31 Jan 2003:
- - minimal setup for CardBus bridges
- - add EEPROM read/write support in the CS8900 driver
- - add support for the builtin I2C controller in the Samsung s3c24x0 chips
- - add support for MPL's VCMA9 (Samsung s3c2410 based) board
-
-* Patch by Steven Scholz, 04 Feb 2003:
- add support for RTC DS1307
-
-* Patch by Reinhard Meyer, 5 Feb 2003:
- fix PLPRCR/SCCR init sequence on 8xx to allow for
- changes of EBDF by software
-
-* Patch by Vladimir Gurevich, 07 Feb 2003:
- "API-compatibility patch" for 4xx I2C driver
-
-* TRAB fixes / extensions:
- - Restore VFD brightness as saved in environment
- - add support for Fujitsu flashes
- - make sure both buzzers are turned off (drive low level)
-
-* Patches by Robert Schwebel, 06 Mar 2003:
- - fix bug in BOOTP code (must use NetCopyIP)
- - update of CSB226 port
- - clear BSS segment on XScale
- - added support for i2c_init_board() function
- - update to the Innokom plattform
-
-* Extend support for redundand environments for configurations where
- environment size < sector size
-
-* Patch by Rune Torgersen, 13 Feb 2003:
- Add support for Motorola MPC8266ADS board
-
-* Patch by Kyle Harris, 19 Feb 2003:
- patches for the Intel lubbock board:
- memsetup.S - general cleanup (based on Robert's csb226 code)
- flash.c - overhaul, actually works now
- lubbock.c - fix init funcs to return proper value
-
-* Patch by Kenneth Johansson, 26 Feb 2003:
- - Fixed off by one in RFTA calculation.
- - No need to abort when LDF is lower than we can program it's only
- minimum timing so clamp it to what we can do.
- - Takes function pointer to function for reading the spd_nvram. Usefull
- for faking data or hardcode a module without the nvram.
- - fix other user for above change
- - fix some comments.
-
-* Patches by Brian Waite, 26 Feb 2003:
- - fix port for evb64260 board
- - fix PCI for evb64260 board
- - fix PCI scan
-
-* Patch by Reinhard Meyer, 1 Mar 2003:
- Add support for EMK TOP860 Module
-
-* Patch by Yuli Barcohen, 02 Mar 2003:
- Add SPD EEPROM support for MPC8260ADS board
-
-* Patch by Robert Schwebel, 21 Jan 2003:
- - Add support for Innokom board
- - Don't complain if "install" fails
- - README cleanup (remove duplicated lines)
- - Update PXA header files
-
-* Add documentation for existing POST code (doc/README.POST)
-
-* Patch by Laudney Ren, 15 Jan 2003:
- Fix handling of redundand environment in "tools/envcrc.c"
-
-* Patch by Detlev Zundel, 28 Feb 2003:
- Add bedbug support for 824x systems
-
-* Add support for 16 MB flash configuration of TRAB board
-
-* Patch by Erwin Rol, 27 Feb 2003:
- Add support for RTEMS
-
-* Add image information to README
-
-* Patch by Stefan Roese, 18 Feb 2003:
- CPCIISER4 configuration updated.
-
-* Patch by Stefan Roese, 17 Feb 2003:
- Fixed bug in ext. serial clock setup on PPC405 (since PPC440 port).
-
-* Patch by Stefan Roese, 13 Feb 2003:
- Add "pcidelay" environment variable (in ms, enabled via
- CONFIG_PCI_BOOTDELAY).
- PCI spec 2.2 defines, that a pci target has 2^25 pci clocks after
- RST# to respond to configuration cycles (33MHz -> 1s).
-
-* Fix dual PCMCIA slot support (when running with just one
- slot populated)
-
-* Add VFD type detection to trab board
-
-* extend drivers/cs8900.c driver to synchronize ethaddr environment
- variable with value in the EEPROM
-
-* Patch by Stefan Roese, 10 Feb 2003:
- Add support for 4MB and 128MB onboard SDRAM (cpu/ppc4xx/sdram.c)
-
-* Add support for MIPS32 4Kc CPUs
-
-* Add support for INCA-IP Board
-
-======================================================================
-Changes for U-Boot 0.2.2:
-======================================================================
-
-* Add dual ethernet support on PM826
-
-* Add support for LXT971 PHY on PM826
-
-* Patch by Tord Andersson, 16 Jan 2003:
- Fix flash sector count for TQM8xxL
-
-* Fix I2C EEPROM problem on ICU862 board (would only write the first
- 16 bytes out of each 32 byte block)
-
-======================================================================
-Changes for U-Boot 0.2.1:
-======================================================================
-
-* Add support for V37 board
- (patch by Jón Benediktsson, 11 Dec 2002)
-
-* Update baudrate in bd_info when it gets changed
-
-* Add watchdog trigger points while waiting for serial port
- (so far only 8xx -- needed on LWMON with 100ms watchdog)
-
-* Improve command line tool to access the U-Boot's environment
- (figuration of the utility, using a config file)
-
-* Add single quote support for (old) command line parser
-
-* Switch LWMON board default config from FRAM to EEPROM;
- in POST, EEPROM shows up on 8 addresses
-
-======================================================================
-Changes for U-Boot 0.2.0:
-======================================================================
-
-* Use 1-byte-read instead of -write for iprobe() function
- Add i2c commands to PM826 config
-
-* extend I2C POST code: check for list on known addresses
-
-* Improve log buffer code; use "loglevel" to decide which messages
- to log on the console, too (like in Linux); get rid of "logstart"
-
-* Add command line tool to access the U-Boot's environment
- (board-specific for TRAB now, to be fixed later)
-
-* Patch by Hans-Joerg Frieden, 06 Dec 2002
- Fix misc problems with AmigaOne support
-
-* Patch by Chris Hallinan, 3 Dec 2002:
- minor cleanup to the MPC8245 EPIC driver
-
-* Patch by Pierre Aubert , 28 Nov 2002
- Add support for external (SIU) interrupts on MPC8xx
-
-* Patch by Pierre Aubert , 28 Nov 2002
- Fix nested syscalls bug in standalone applications
-
-* Patch by David Müller, 27 Nov 2002:
- fix output of "pciinfo" command for CardBus bridge devices.
-
-* Fix bug in TQM8260 board detection - boards got stuck when board ID
- was not readable
-
-* Add LED indication for IDE activity on KUP4K board
-
-* Fix startup problems with VFD display on TRAB
-
-* Patch by Pierre Aubert, 20 Nov 2002
- Add driver for Epson SED13806 graphic controller.
- Add support for BMP logos in cfb_console driver.
-
-* Added support for both PCMCIA slots (at the same time!) on MPC8xx
-
-* Patch by Rod Boyce, 21 Nov 2002:
- fix PCMCIA on MBX8xx board
-
-* Patch by Pierre Aubert , 21 Nov 2002
- Add CFG_CPM_POST_WORD_ADDR to make the offset of the
- bootmode word in DPRAM configurable
-
-* Patch by Daniel Engström, 18 Nov 2002:
- Fixes for x86 port (mostly strings issues)
-
-* Patch by Ken Chou, 18 Nov 2002:
- Fix for natsemi NIC cards (DP83815)
-
-* Patch by Pierre Aubert, 19 Nov 2002:
- fix a bug for the MII configuration, and some warnings
-
-* Patch by Thomas Frieden, 13 Nov 2002:
- Add code for AmigaOne board
- (preliminary merge to U-Boot, still WIP)
-
-* Patch by Jon Diekema, 12 Nov 2002:
- - Adding URL for IEEE OUI lookup
- - Making the autoboot #defines dependent on CONFIG_AUTOBOOT_KEYED
- being defined.
- - In the CONFIG_EXTRA_ENV_SETTINGS #define, the root-on-initrd and
- root-on-nfs macros are designed to switch how the default boot
- method gets defined.
-
-* Patch by Daniel Engström, 13 Nov 2002:
- Add support for i386 architecture and AMD SC520 board
-
-* Patch by Pierre Aubert, 12 Nov 2002:
- Add support for DOS filesystem and booting from DOS floppy disk
-
-* Patch by Jim Sandoz, 07 Nov 2002:
- Increase number of network RX buffers (PKTBUFSRX in
- "include/net.h") for EEPRO100 based boards (especially SP8240)
- which showed "Receiver is not ready" errors when U-Boot was
- processing the receive buffers slower than the network controller
- was filling them.
-
-* Patch by Andreas Oberritter, 09 Nov 2002:
- Change behaviour of NetLoop(): return -1 for errors, filesize
- otherwise; return code 0 is valid an means no file loaded - in this
- case the environment still gets updated!
-
-* Patches by Jon Diekema, 9 Nov 2002:
- - improve ADC/DAC clocking on the SACSng board to align
- the failing edges of LRCLK and SCLK
- - sbc8260 configuration tweaks
- - add status LED support for 82xx systems
- - wire sspi/sspo commands into command handler; improved error
- handlering
- - add timestamp support and alternate memory test to the
- SACSng configuration
-
-* Patch by Vince Husovsky, 7 Nov 2002:
- Add "-n" to linker options to get rid of "Not enough room for
- program headers" problem
-
-* Patch by David Müller, 05 Nov 2002
- Rename CONFIG_PLL_INPUT_FREQ to CONFIG_SYS_CLK_FREQ
- so we can use an already existing name
-
-* Patch by Pierre Aubert, 05 Nov 2002
- Hardware relatied improvments in FDC boot code
-
-* Patch by Holger Schurig, 5 Nov 2002:
- Make the PXA really change it's frequency
-
-* Patch by Pierre Aubert, 05 Nov 2002
- Add support for slave serial Spartan 2 FPGAs
-
-* Fix uninitialized memory (MAC address) in 8xx SCC/FEC ethernet
- drivers
-
-* Add support for log buffer which can be passed to Linux kernel's
- syslog mechanism; used especially for POST results.
-
-* Patch by Klaus Heydeck, 31 Oct 2002:
- Add initial support for kup4k board
-
-* Patch by Robert Schwebel, 04 Nov 2002:
- - use watchdog to reset PXA250 systems
- - added progress callbacks to (some of the) ARM code
- - update for Cogent CSB226 board
-
-* Add support for FPS860 board
-
-* Patch by Guillaume Alexandre,, 04 Nov 2002:
- Improve PCI access on 32-bits Compact PCI bus
-
-* Fix mdelay() on TRAB - this was still the debugging version with
- seconds instead of ms.
-
-* Patch by Robert Schwebel, 1 Nov 2002:
- XScale related cleanup (affects all ARM boards)
-
-* Cleanup of names and README.
-
-======================================================================
-Notes for U-Boot 0.1.0:
-======================================================================
-
-This is the initial version of "Das U-Boot", the Universal Boot Loader.
-
-It is based on version 2.0.0 (the "Halloween Release") of PPCBoot.
-For information about the history of the project please see the
-PPCBoot project page at http://sourceforge.net/projects/ppcboot
-
-======================================================================