Documentation/devicetree/bindings/mmc/sdhci-st.txt

   1 * STMicroelectronics sdhci-st MMC/SD controller
   2
   3 This file documents the differences between the core properties in
   4 Documentation/devicetree/bindings/mmc/mmc.txt and the properties
   5 used by the sdhci-st driver.
   6
   7 Required properties:
   8 - compatible:           Must be "st,sdhci" and it can be compatible to "st,sdhci-stih407"
   9                         to set the internal glue logic used for configuring the MMC
  10                         subsystem (mmcss) inside the FlashSS (available in STiH407 SoC
  11                         family).
  12
  13 - clock-names:          Should be "mmc".
  14                         See: Documentation/devicetree/bindings/resource-names.txt
  15 - clocks:               Phandle to the clock.
  16                         See: Documentation/devicetree/bindings/clock/clock-bindings.txt
  17
  18 - interrupts:           One mmc interrupt should be described here.
  19 - interrupt-names:      Should be "mmcirq".
  20
  21 - pinctrl-names:        A pinctrl state names "default" must be defined.
  22 - pinctrl-0:            Phandle referencing pin configuration of the sd/emmc controller.
  23                         See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
  24
  25 - reg:                  This must provide the host controller base address and it can also
  26                         contain the FlashSS Top register for TX/RX delay used by the driver
  27                         to configure DLL inside the flashSS, if so reg-names must also be
  28                         specified.
  29
  30 Optional properties:
  31 - reg-names:            Should be "mmc" and "top-mmc-delay". "top-mmc-delay" is optional
  32                         for eMMC on stih407 family silicon to configure DLL inside FlashSS.
  33
  34 - non-removable:        Non-removable slot. Also used for configuring mmcss in STiH407 SoC
  35                         family.
  36                         See:  Documentation/devicetree/bindings/mmc/mmc.txt.
  37
  38 - bus-width:            Number of data lines.
  39                         See:  Documentation/devicetree/bindings/mmc/mmc.txt.
  40
  41 - max-frequency:        Can be 200MHz, 100Mz or 50MHz (default) and used for
  42                         configuring the CCONFIG3 in the mmcss.
  43                         See:  Documentation/devicetree/bindings/mmc/mmc.txt.
  44
  45 - resets:               Phandle and reset specifier pair to softreset line of HC IP.
  46                         See: Documentation/devicetree/bindings/reset/reset.txt
  47
  48 - vqmmc-supply:         Phandle to the regulator dt node, mentioned as the vcc/vdd
  49                         supply in eMMC/SD specs.
  50
  51 - sd-uhs--sdr50:        To enable the SDR50 in the mmcss.
  52                         See:  Documentation/devicetree/bindings/mmc/mmc.txt.
  53
  54 - sd-uhs-sdr104:        To enable the SDR104 in the mmcss.
  55                         See:  Documentation/devicetree/bindings/mmc/mmc.txt.
  56
  57 - sd-uhs-ddr50:         To enable the DDR50 in the mmcss.
  58                         See:  Documentation/devicetree/bindings/mmc/mmc.txt.
  59
  60 Example:
  61
  62 /* Example stih416e eMMC configuration */
  63
  64 mmc0: sdhci@fe81e000 {
  65         compatible      = "st,sdhci";
  66         status          = "disabled";
  67         reg             = <0xfe81e000 0x1000>;
  68         interrupts      = <GIC_SPI 127 IRQ_TYPE_NONE>;
  69         interrupt-names = "mmcirq";
  70         pinctrl-names   = "default";
  71         pinctrl-0       = <&pinctrl_mmc0>;
  72         clock-names     = "mmc";
  73         clocks          = <&clk_s_a1_ls 1>;
  74         bus-width       = <8>
  75
  76 /* Example SD stih407 family configuration */
  77
  78 mmc1: sdhci@09080000 {
  79         compatible      = "st,sdhci-stih407", "st,sdhci";
  80         status          = "disabled";
  81         reg             = <0x09080000 0x7ff>;
  82         reg-names       = "mmc";
  83         interrupts      = <GIC_SPI 90 IRQ_TYPE_NONE>;
  84         interrupt-names = "mmcirq";
  85         pinctrl-names   = "default";
  86         pinctrl-0       = <&pinctrl_sd1>;
  87         clock-names     = "mmc";
  88         clocks          = <&clk_s_c0_flexgen CLK_MMC_1>;
  89         resets          = <&softreset STIH407_MMC1_SOFTRESET>;
  90         bus-width       = <4>;
  91 };
  92
  93 /* Example eMMC stih407 family configuration */
  94
  95 mmc0: sdhci@09060000 {
  96         compatible      = "st,sdhci-stih407", "st,sdhci";
  97         status          = "disabled";
  98         reg             = <0x09060000 0x7ff>, <0x9061008 0x20>;
  99         reg-names       = "mmc", "top-mmc-delay";
 100         interrupts      = <GIC_SPI 92 IRQ_TYPE_NONE>;
 101         interrupt-names = "mmcirq";
 102         pinctrl-names   = "default";
 103         pinctrl-0       = <&pinctrl_mmc0>;
 104         clock-names     = "mmc";
 105         clocks          = <&clk_s_c0_flexgen CLK_MMC_0>;
 106         vqmmc-supply    = <&vmmc_reg>;
 107         max-frequency   = <200000000>;
 108         bus-width       = <8>;
 109         non-removable;
 110         sd-uhs-sdr50;
 111         sd-uhs-sdr104;
 112         sd-uhs-ddr50;
 113 };