arch/arm/boot/dts/tegra124-nyan.dtsi

   1 #include <dt-bindings/input/input.h>
   2 #include "tegra124.dtsi"
   3
   4 / {
   5         aliases {
   6                 rtc0 = "/i2c@0,7000d000/pmic@40";
   7                 rtc1 = "/rtc@0,7000e000";
   8                 serial0 = &uarta;
   9         };
  10
  11         memory {
  12                 reg = <0x0 0x80000000 0x0 0x80000000>;
  13         };
  14
  15         host1x@0,50000000 {
  16                 hdmi@0,54280000 {
  17                         status = "okay";
  18
  19                         vdd-supply = <&vdd_3v3_hdmi>;
  20                         pll-supply = <&vdd_hdmi_pll>;
  21                         hdmi-supply = <&vdd_5v0_hdmi>;
  22
  23                         nvidia,ddc-i2c-bus = <&hdmi_ddc>;
  24                         nvidia,hpd-gpio =
  25                                 <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
  26                 };
  27
  28                 sor@0,54540000 {
  29                         status = "okay";
  30
  31                         nvidia,dpaux = <&dpaux>;
  32                         nvidia,panel = <&panel>;
  33                 };
  34
  35                 dpaux@0,545c0000 {
  36                         vdd-supply = <&vdd_3v3_panel>;
  37                         status = "okay";
  38                 };
  39         };
  40
  41         serial@0,70006000 {
  42                 /* Debug connector on the bottom of the board near SD card. */
  43                 status = "okay";
  44         };
  45
  46         pwm@0,7000a000 {
  47                 status = "okay";
  48         };
  49
  50         i2c@0,7000c000 {
  51                 status = "okay";
  52                 clock-frequency = <100000>;
  53
  54                 acodec: audio-codec@10 {
  55                         compatible = "maxim,max98090";
  56                         reg = <0x10>;
  57                         interrupt-parent = <&gpio>;
  58                         interrupts = <TEGRA_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
  59                 };
  60
  61                 temperature-sensor@4c {
  62                         compatible = "ti,tmp451";
  63                         reg = <0x4c>;
  64                         interrupt-parent = <&gpio>;
  65                         interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
  66
  67                         #thermal-sensor-cells = <1>;
  68                 };
  69         };
  70
  71         i2c@0,7000c400 {
  72                 status = "okay";
  73                 clock-frequency = <100000>;
  74
  75                 trackpad@15 {
  76                         compatible = "elan,ekth3000";
  77                         reg = <0x15>;
  78                         interrupt-parent = <&gpio>;
  79                         interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_FALLING>;
  80                         wakeup-source;
  81                 };
  82         };
  83
  84         i2c@0,7000c500 {
  85                 status = "okay";
  86                 clock-frequency = <400000>;
  87
  88                 tpm@20 {
  89                         compatible = "infineon,slb9645tt";
  90                         reg = <0x20>;
  91                 };
  92         };
  93
  94         hdmi_ddc: i2c@0,7000c700 {
  95                 status = "okay";
  96                 clock-frequency = <100000>;
  97         };
  98
  99         i2c@0,7000d000 {
 100                 status = "okay";
 101                 clock-frequency = <400000>;
 102
 103                 pmic: pmic@40 {
 104                         compatible = "ams,as3722";
 105                         reg = <0x40>;
 106                         interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
 107
 108                         ams,system-power-controller;
 109
 110                         #interrupt-cells = <2>;
 111                         interrupt-controller;
 112
 113                         gpio-controller;
 114                         #gpio-cells = <2>;
 115
 116                         pinctrl-names = "default";
 117                         pinctrl-0 = <&as3722_default>;
 118
 119                         as3722_default: pinmux {
 120                                 gpio0 {
 121                                         pins = "gpio0";
 122                                         function = "gpio";
 123                                         bias-pull-down;
 124                                 };
 125
 126                                 gpio1 {
 127                                         pins = "gpio1";
 128                                         function = "gpio";
 129                                         bias-pull-up;
 130                                 };
 131
 132                                 gpio2_4_7 {
 133                                         pins = "gpio2", "gpio4", "gpio7";
 134                                         function = "gpio";
 135                                         bias-pull-up;
 136                                 };
 137
 138                                 gpio3_6 {
 139                                         pins = "gpio3", "gpio6";
 140                                         bias-high-impedance;
 141                                 };
 142
 143                                 gpio5 {
 144                                         pins = "gpio5";
 145                                         function = "clk32k-out";
 146                                         bias-pull-down;
 147                                 };
 148                         };
 149
 150                         regulators {
 151                                 vsup-sd2-supply = <&vdd_5v0_sys>;
 152                                 vsup-sd3-supply = <&vdd_5v0_sys>;
 153                                 vsup-sd4-supply = <&vdd_5v0_sys>;
 154                                 vsup-sd5-supply = <&vdd_5v0_sys>;
 155                                 vin-ldo0-supply = <&vdd_1v35_lp0>;
 156                                 vin-ldo1-6-supply = <&vdd_3v3_run>;
 157                                 vin-ldo2-5-7-supply = <&vddio_1v8>;
 158                                 vin-ldo3-4-supply = <&vdd_3v3_sys>;
 159                                 vin-ldo9-10-supply = <&vdd_5v0_sys>;
 160                                 vin-ldo11-supply = <&vdd_3v3_run>;
 161
 162                                 vdd_cpu: sd0 {
 163                                         regulator-name = "+VDD_CPU_AP";
 164                                         regulator-min-microvolt = <700000>;
 165                                         regulator-max-microvolt = <1350000>;
 166                                         regulator-min-microamp = <3500000>;
 167                                         regulator-max-microamp = <3500000>;
 168                                         regulator-always-on;
 169                                         regulator-boot-on;
 170                                         ams,ext-control = <2>;
 171                                 };
 172
 173                                 sd1 {
 174                                         regulator-name = "+VDD_CORE";
 175                                         regulator-min-microvolt = <700000>;
 176                                         regulator-max-microvolt = <1350000>;
 177                                         regulator-min-microamp = <2500000>;
 178                                         regulator-max-microamp = <4000000>;
 179                                         regulator-always-on;
 180                                         regulator-boot-on;
 181                                         ams,ext-control = <1>;
 182                                 };
 183
 184                                 vdd_1v35_lp0: sd2 {
 185                                         regulator-name = "+1.35V_LP0(sd2)";
 186                                         regulator-min-microvolt = <1350000>;
 187                                         regulator-max-microvolt = <1350000>;
 188                                         regulator-always-on;
 189                                         regulator-boot-on;
 190                                 };
 191
 192                                 sd3 {
 193                                         regulator-name = "+1.35V_LP0(sd3)";
 194                                         regulator-min-microvolt = <1350000>;
 195                                         regulator-max-microvolt = <1350000>;
 196                                         regulator-always-on;
 197                                         regulator-boot-on;
 198                                 };
 199
 200                                 vdd_1v05_run: sd4 {
 201                                         regulator-name = "+1.05V_RUN";
 202                                         regulator-min-microvolt = <1050000>;
 203                                         regulator-max-microvolt = <1050000>;
 204                                 };
 205
 206                                 vddio_1v8: sd5 {
 207                                         regulator-name = "+1.8V_VDDIO";
 208                                         regulator-min-microvolt = <1800000>;
 209                                         regulator-max-microvolt = <1800000>;
 210                                         regulator-always-on;
 211                                 };
 212
 213                                 sd6 {
 214                                         regulator-name = "+VDD_GPU_AP";
 215                                         regulator-min-microvolt = <650000>;
 216                                         regulator-max-microvolt = <1200000>;
 217                                         regulator-min-microamp = <3500000>;
 218                                         regulator-max-microamp = <3500000>;
 219                                         regulator-boot-on;
 220                                         regulator-always-on;
 221                                 };
 222
 223                                 ldo0 {
 224                                         regulator-name = "+1.05V_RUN_AVDD";
 225                                         regulator-min-microvolt = <1050000>;
 226                                         regulator-max-microvolt = <1050000>;
 227                                         regulator-boot-on;
 228                                         regulator-always-on;
 229                                         ams,ext-control = <1>;
 230                                 };
 231
 232                                 ldo1 {
 233                                         regulator-name = "+1.8V_RUN_CAM";
 234                                         regulator-min-microvolt = <1800000>;
 235                                         regulator-max-microvolt = <1800000>;
 236                                 };
 237
 238                                 ldo2 {
 239                                         regulator-name = "+1.2V_GEN_AVDD";
 240                                         regulator-min-microvolt = <1200000>;
 241                                         regulator-max-microvolt = <1200000>;
 242                                         regulator-boot-on;
 243                                         regulator-always-on;
 244                                 };
 245
 246                                 ldo3 {
 247                                         regulator-name = "+1.00V_LP0_VDD_RTC";
 248                                         regulator-min-microvolt = <1000000>;
 249                                         regulator-max-microvolt = <1000000>;
 250                                         regulator-boot-on;
 251                                         regulator-always-on;
 252                                         ams,enable-tracking;
 253                                 };
 254
 255                                 vdd_run_cam: ldo4 {
 256                                         regulator-name = "+3.3V_RUN_CAM";
 257                                         regulator-min-microvolt = <2800000>;
 258                                         regulator-max-microvolt = <2800000>;
 259                                 };
 260
 261                                 ldo5 {
 262                                         regulator-name = "+1.2V_RUN_CAM_FRONT";
 263                                         regulator-min-microvolt = <1200000>;
 264                                         regulator-max-microvolt = <1200000>;
 265                                 };
 266
 267                                 vddio_sdmmc3: ldo6 {
 268                                         regulator-name = "+VDDIO_SDMMC3";
 269                                         regulator-min-microvolt = <1800000>;
 270                                         regulator-max-microvolt = <3300000>;
 271                                 };
 272
 273                                 ldo7 {
 274                                         regulator-name = "+1.05V_RUN_CAM_REAR";
 275                                         regulator-min-microvolt = <1050000>;
 276                                         regulator-max-microvolt = <1050000>;
 277                                 };
 278
 279                                 ldo9 {
 280                                         regulator-name = "+2.8V_RUN_TOUCH";
 281                                         regulator-min-microvolt = <2800000>;
 282                                         regulator-max-microvolt = <2800000>;
 283                                 };
 284
 285                                 ldo10 {
 286                                         regulator-name = "+2.8V_RUN_CAM_AF";
 287                                         regulator-min-microvolt = <2800000>;
 288                                         regulator-max-microvolt = <2800000>;
 289                                 };
 290
 291                                 ldo11 {
 292                                         regulator-name = "+1.8V_RUN_VPP_FUSE";
 293                                         regulator-min-microvolt = <1800000>;
 294                                         regulator-max-microvolt = <1800000>;
 295                                 };
 296                         };
 297                 };
 298         };
 299
 300         spi@0,7000d400 {
 301                 status = "okay";
 302
 303                 cros_ec: cros-ec@0 {
 304                         compatible = "google,cros-ec-spi";
 305                         spi-max-frequency = <3000000>;
 306                         interrupt-parent = <&gpio>;
 307                         interrupts = <TEGRA_GPIO(C, 7) IRQ_TYPE_LEVEL_LOW>;
 308                         reg = <0>;
 309
 310                         google,cros-ec-spi-msg-delay = <2000>;
 311
 312                         i2c-tunnel {
 313                                 compatible = "google,cros-ec-i2c-tunnel";
 314                                 #address-cells = <1>;
 315                                 #size-cells = <0>;
 316
 317                                 google,remote-bus = <0>;
 318
 319                                 charger: bq24735@9 {
 320                                         compatible = "ti,bq24735";
 321                                         reg = <0x9>;
 322                                         interrupt-parent = <&gpio>;
 323                                         interrupts = <TEGRA_GPIO(J, 0)
 324                                                         GPIO_ACTIVE_HIGH>;
 325                                         ti,ac-detect-gpios = <&gpio
 326                                                         TEGRA_GPIO(J, 0)
 327                                                         GPIO_ACTIVE_HIGH>;
 328                                 };
 329
 330                                 battery: sbs-battery@b {
 331                                         compatible = "sbs,sbs-battery";
 332                                         reg = <0xb>;
 333                                         sbs,i2c-retry-count = <2>;
 334                                         sbs,poll-retry-count = <10>;
 335                                         power-supplies = <&charger>;
 336                                 };
 337                         };
 338                 };
 339         };
 340
 341         spi@0,7000da00 {
 342                 status = "okay";
 343                 spi-max-frequency = <25000000>;
 344
 345                 flash@0 {
 346                         compatible = "winbond,w25q32dw";
 347                         spi-max-frequency = <25000000>;
 348                         reg = <0>;
 349                 };
 350         };
 351
 352         pmc@0,7000e400 {
 353                 nvidia,invert-interrupt;
 354                 nvidia,suspend-mode = <0>;
 355                 nvidia,cpu-pwr-good-time = <500>;
 356                 nvidia,cpu-pwr-off-time = <300>;
 357                 nvidia,core-pwr-good-time = <641 3845>;
 358                 nvidia,core-pwr-off-time = <61036>;
 359                 nvidia,core-power-req-active-high;
 360                 nvidia,sys-clock-req-active-high;
 361         };
 362
 363         hda@0,70030000 {
 364                 status = "okay";
 365         };
 366
 367         sdhci0_pwrseq: sdhci0_pwrseq {
 368                 compatible = "mmc-pwrseq-simple";
 369
 370                 reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
 371         };
 372
 373         sdhci@0,700b0000 { /* WiFi/BT on this bus */
 374                 status = "okay";
 375                 bus-width = <4>;
 376                 no-1-8-v;
 377                 non-removable;
 378                 mmc-pwrseq = <&sdhci0_pwrseq>;
 379                 vmmc-supply = <&vdd_3v3_lp0>;
 380                 vqmmc-supply = <&vddio_1v8>;
 381                 keep-power-in-suspend;
 382         };
 383
 384         sdhci@0,700b0400 { /* SD Card on this bus */
 385                 status = "okay";
 386                 cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 387                 power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
 388                 bus-width = <4>;
 389                 no-1-8-v;
 390                 vqmmc-supply = <&vddio_sdmmc3>;
 391         };
 392
 393         sdhci@0,700b0600 { /* eMMC on this bus */
 394                 status = "okay";
 395                 bus-width = <8>;
 396                 no-1-8-v;
 397                 non-removable;
 398         };
 399
 400         /* CPU DFLL clock */
 401         clock@0,70110000 {
 402                 status = "okay";
 403                 vdd-cpu-supply = <&vdd_cpu>;
 404                 nvidia,i2c-fs-rate = <400000>;
 405         };
 406
 407         ahub@0,70300000 {
 408                 i2s@0,70301100 {
 409                         status = "okay";
 410                 };
 411         };
 412
 413         usb@0,7d000000 { /* Rear external USB port. */
 414                 status = "okay";
 415         };
 416
 417         usb-phy@0,7d000000 {
 418                 status = "okay";
 419                 vbus-supply = <&vdd_usb1_vbus>;
 420         };
 421
 422         usb@0,7d004000 { /* Internal webcam. */
 423                 status = "okay";
 424         };
 425
 426         usb-phy@0,7d004000 {
 427                 status = "okay";
 428                 vbus-supply = <&vdd_run_cam>;
 429         };
 430
 431         usb@0,7d008000 { /* Left external USB port. */
 432                 status = "okay";
 433         };
 434
 435         usb-phy@0,7d008000 {
 436                 status = "okay";
 437                 vbus-supply = <&vdd_usb3_vbus>;
 438         };
 439
 440         backlight: backlight {
 441                 compatible = "pwm-backlight";
 442
 443                 enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
 444                 power-supply = <&vdd_led>;
 445                 pwms = <&pwm 1 1000000>;
 446
 447                 default-brightness-level = <224>;
 448                 brightness-levels =
 449                         <  0   1   2   3   4   5   6   7
 450                            8   9  10  11  12  13  14  15
 451                           16  17  18  19  20  21  22  23
 452                           24  25  26  27  28  29  30  31
 453                           32  33  34  35  36  37  38  39
 454                           40  41  42  43  44  45  46  47
 455                           48  49  50  51  52  53  54  55
 456                           56  57  58  59  60  61  62  63
 457                           64  65  66  67  68  69  70  71
 458                           72  73  74  75  76  77  78  79
 459                           80  81  82  83  84  85  86  87
 460                           88  89  90  91  92  93  94  95
 461                           96  97  98  99 100 101 102 103
 462                          104 105 106 107 108 109 110 111
 463                          112 113 114 115 116 117 118 119
 464                          120 121 122 123 124 125 126 127
 465                          128 129 130 131 132 133 134 135
 466                          136 137 138 139 140 141 142 143
 467                          144 145 146 147 148 149 150 151
 468                          152 153 154 155 156 157 158 159
 469                          160 161 162 163 164 165 166 167
 470                          168 169 170 171 172 173 174 175
 471                          176 177 178 179 180 181 182 183
 472                          184 185 186 187 188 189 190 191
 473                          192 193 194 195 196 197 198 199
 474                          200 201 202 203 204 205 206 207
 475                          208 209 210 211 212 213 214 215
 476                          216 217 218 219 220 221 222 223
 477                          224 225 226 227 228 229 230 231
 478                          232 233 234 235 236 237 238 239
 479                          240 241 242 243 244 245 246 247
 480                          248 249 250 251 252 253 254 255
 481                          256>;
 482         };
 483
 484         clocks {
 485                 compatible = "simple-bus";
 486                 #address-cells = <1>;
 487                 #size-cells = <0>;
 488
 489                 clk32k_in: clock@0 {
 490                         compatible = "fixed-clock";
 491                         reg = <0>;
 492                         #clock-cells = <0>;
 493                         clock-frequency = <32768>;
 494                 };
 495         };
 496
 497         cpus {
 498                 cpu@0 {
 499                         vdd-cpu-supply = <&vdd_cpu>;
 500                 };
 501         };
 502
 503         gpio-keys {
 504                 compatible = "gpio-keys";
 505
 506                 lid {
 507                         label = "Lid";
 508                         gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>;
 509                         linux,input-type = <5>;
 510                         linux,code = <KEY_RESERVED>;
 511                         debounce-interval = <1>;
 512                         gpio-key,wakeup;
 513                 };
 514
 515                 power {
 516                         label = "Power";
 517                         gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 518                         linux,code = <KEY_POWER>;
 519                         debounce-interval = <30>;
 520                         gpio-key,wakeup;
 521                 };
 522         };
 523
 524         regulators {
 525                 compatible = "simple-bus";
 526                 #address-cells = <1>;
 527                 #size-cells = <0>;
 528
 529                 vdd_mux: regulator@0 {
 530                         compatible = "regulator-fixed";
 531                         reg = <0>;
 532                         regulator-name = "+VDD_MUX";
 533                         regulator-min-microvolt = <12000000>;
 534                         regulator-max-microvolt = <12000000>;
 535                         regulator-always-on;
 536                         regulator-boot-on;
 537                 };
 538
 539                 vdd_5v0_sys: regulator@1 {
 540                         compatible = "regulator-fixed";
 541                         reg = <1>;
 542                         regulator-name = "+5V_SYS";
 543                         regulator-min-microvolt = <5000000>;
 544                         regulator-max-microvolt = <5000000>;
 545                         regulator-always-on;
 546                         regulator-boot-on;
 547                         vin-supply = <&vdd_mux>;
 548                 };
 549
 550                 vdd_3v3_sys: regulator@2 {
 551                         compatible = "regulator-fixed";
 552                         reg = <2>;
 553                         regulator-name = "+3.3V_SYS";
 554                         regulator-min-microvolt = <3300000>;
 555                         regulator-max-microvolt = <3300000>;
 556                         regulator-always-on;
 557                         regulator-boot-on;
 558                         vin-supply = <&vdd_mux>;
 559                 };
 560
 561                 vdd_3v3_run: regulator@3 {
 562                         compatible = "regulator-fixed";
 563                         reg = <3>;
 564                         regulator-name = "+3.3V_RUN";
 565                         regulator-min-microvolt = <3300000>;
 566                         regulator-max-microvolt = <3300000>;
 567                         regulator-always-on;
 568                         regulator-boot-on;
 569                         gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
 570                         enable-active-high;
 571                         vin-supply = <&vdd_3v3_sys>;
 572                 };
 573
 574                 vdd_3v3_hdmi: regulator@4 {
 575                         compatible = "regulator-fixed";
 576                         reg = <4>;
 577                         regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
 578                         regulator-min-microvolt = <3300000>;
 579                         regulator-max-microvolt = <3300000>;
 580                         vin-supply = <&vdd_3v3_run>;
 581                 };
 582
 583                 vdd_led: regulator@5 {
 584                         compatible = "regulator-fixed";
 585                         reg = <5>;
 586                         regulator-name = "+VDD_LED";
 587                         gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
 588                         enable-active-high;
 589                         vin-supply = <&vdd_mux>;
 590                 };
 591
 592                 vdd_5v0_ts: regulator@6 {
 593                         compatible = "regulator-fixed";
 594                         reg = <6>;
 595                         regulator-name = "+5V_VDD_TS_SW";
 596                         regulator-min-microvolt = <5000000>;
 597                         regulator-max-microvolt = <5000000>;
 598                         regulator-boot-on;
 599                         gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
 600                         enable-active-high;
 601                         vin-supply = <&vdd_5v0_sys>;
 602                 };
 603
 604                 vdd_usb1_vbus: regulator@7 {
 605                         compatible = "regulator-fixed";
 606                         reg = <7>;
 607                         regulator-name = "+5V_USB_HS";
 608                         regulator-min-microvolt = <5000000>;
 609                         regulator-max-microvolt = <5000000>;
 610                         gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
 611                         enable-active-high;
 612                         gpio-open-drain;
 613                         vin-supply = <&vdd_5v0_sys>;
 614                 };
 615
 616                 vdd_usb3_vbus: regulator@8 {
 617                         compatible = "regulator-fixed";
 618                         reg = <8>;
 619                         regulator-name = "+5V_USB_SS";
 620                         regulator-min-microvolt = <5000000>;
 621                         regulator-max-microvolt = <5000000>;
 622                         gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
 623                         enable-active-high;
 624                         gpio-open-drain;
 625                         vin-supply = <&vdd_5v0_sys>;
 626                 };
 627
 628                 vdd_3v3_panel: regulator@9 {
 629                         compatible = "regulator-fixed";
 630                         reg = <9>;
 631                         regulator-name = "+3.3V_PANEL";
 632                         regulator-min-microvolt = <3300000>;
 633                         regulator-max-microvolt = <3300000>;
 634                         gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
 635                         enable-active-high;
 636                         vin-supply = <&vdd_3v3_run>;
 637                 };
 638
 639                 vdd_3v3_lp0: regulator@10 {
 640                         compatible = "regulator-fixed";
 641                         reg = <10>;
 642                         regulator-name = "+3.3V_LP0";
 643                         regulator-min-microvolt = <3300000>;
 644                         regulator-max-microvolt = <3300000>;
 645                         /*
 646                          * TODO: find a way to wire this up with the USB EHCI
 647                          * controllers so that it can be enabled on demand.
 648                          */
 649                         regulator-always-on;
 650                         gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
 651                         enable-active-high;
 652                         vin-supply = <&vdd_3v3_sys>;
 653                 };
 654
 655                 vdd_hdmi_pll: regulator@11 {
 656                         compatible = "regulator-fixed";
 657                         reg = <11>;
 658                         regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
 659                         regulator-min-microvolt = <1050000>;
 660                         regulator-max-microvolt = <1050000>;
 661                         gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
 662                         vin-supply = <&vdd_1v05_run>;
 663                 };
 664
 665                 vdd_5v0_hdmi: regulator@12 {
 666                         compatible = "regulator-fixed";
 667                         reg = <12>;
 668                         regulator-name = "+5V_HDMI_CON";
 669                         regulator-min-microvolt = <5000000>;
 670                         regulator-max-microvolt = <5000000>;
 671                         gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
 672                         enable-active-high;
 673                         vin-supply = <&vdd_5v0_sys>;
 674                 };
 675         };
 676
 677         sound {
 678                 nvidia,audio-routing =
 679                         "Headphones", "HPR",
 680                         "Headphones", "HPL",
 681                         "Speakers", "SPKR",
 682                         "Speakers", "SPKL",
 683                         "Mic Jack", "MICBIAS",
 684                         "DMICL", "Int Mic",
 685                         "DMICR", "Int Mic",
 686                         "IN34", "Mic Jack";
 687
 688                 nvidia,i2s-controller = <&tegra_i2s1>;
 689                 nvidia,audio-codec = <&acodec>;
 690
 691                 clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
 692                          <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
 693                          <&tegra_car TEGRA124_CLK_EXTERN1>;
 694                 clock-names = "pll_a", "pll_a_out0", "mclk";
 695
 696                 nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>;
 697                 nvidia,mic-det-gpios =
 698                                 <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
 699         };
 700
 701         gpio-restart {
 702                 compatible = "gpio-restart";
 703                 gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
 704                 priority = <200>;
 705         };
 706 };
 707
 708 #include "cros-ec-keyboard.dtsi"