Drop all code related to Kconfigs that don't exist.
Fix one Kconfig where it was actually typo:ed (ETRAX_KGB_PORT2)
Drop content related to CRIS v32 SoCs from etraxgpio.h headerfile,
all use of GPIO for both ETRAX FS and ARTPEC-3 should now be through
standard gpiolib instead.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
blo 1b
nop
-#ifdef CONFIG_BLK_DEV_ETRAXIDE
- ;; disable ATA before enabling it in genconfig below
- moveq 0,$r0
- move.d $r0,[R_ATA_CTRL_DATA]
- move.d $r0,[R_ATA_TRANSFER_CNT]
- move.d $r0,[R_ATA_CONFIG]
-#if 0
- move.d R_PORT_G_DATA, $r1
- move.d $r0, [$r1]; assert ATA bus-reset
- nop
- nop
- nop
- nop
- nop
- nop
- move.d 0x08000000,$r0
- move.d $r0,[$r1]
-#endif
-#endif
-
-#ifdef CONFIG_JULIETTE
- ;; configure external DMA channel 0 before enabling it in genconfig
-
- moveq 0,$r0
- move.d $r0,[R_EXT_DMA_0_ADDR]
- ; cnt enable, word size, output, stop, size 0
- move.d IO_STATE (R_EXT_DMA_0_CMD, cnt, enable) \
- | IO_STATE (R_EXT_DMA_0_CMD, rqpol, ahigh) \
- | IO_STATE (R_EXT_DMA_0_CMD, apol, ahigh) \
- | IO_STATE (R_EXT_DMA_0_CMD, rq_ack, burst) \
- | IO_STATE (R_EXT_DMA_0_CMD, wid, word) \
- | IO_STATE (R_EXT_DMA_0_CMD, dir, output) \
- | IO_STATE (R_EXT_DMA_0_CMD, run, stop) \
- | IO_FIELD (R_EXT_DMA_0_CMD, trf_count, 0),$r0
- move.d $r0,[R_EXT_DMA_0_CMD]
-
- ;; reset dma4 and wait for completion
-
- moveq IO_STATE (R_DMA_CH4_CMD, cmd, reset),$r0
- move.b $r0,[R_DMA_CH4_CMD]
-1: move.b [R_DMA_CH4_CMD],$r0
- and.b IO_MASK (R_DMA_CH4_CMD, cmd),$r0
- cmp.b IO_STATE (R_DMA_CH4_CMD, cmd, reset),$r0
- beq 1b
- nop
-
- ;; reset dma5 and wait for completion
-
- moveq IO_STATE (R_DMA_CH5_CMD, cmd, reset),$r0
- move.b $r0,[R_DMA_CH5_CMD]
-1: move.b [R_DMA_CH5_CMD],$r0
- and.b IO_MASK (R_DMA_CH5_CMD, cmd),$r0
- cmp.b IO_STATE (R_DMA_CH5_CMD, cmd, reset),$r0
- beq 1b
- nop
-#endif
-
;; Etrax product HW genconfig setup
moveq 0,$r0
| IO_STATE (R_GEN_CONFIG, dma9, usb),$r0
-#if defined(CONFIG_ETRAX_DEF_R_PORT_G0_DIR_OUT)
- or.d IO_STATE (R_GEN_CONFIG, g0dir, out),$r0
-#endif
-
-#if defined(CONFIG_ETRAX_DEF_R_PORT_G8_15_DIR_OUT)
- or.d IO_STATE (R_GEN_CONFIG, g8_15dir, out),$r0
-#endif
-#if defined(CONFIG_ETRAX_DEF_R_PORT_G16_23_DIR_OUT)
- or.d IO_STATE (R_GEN_CONFIG, g16_23dir, out),$r0
-#endif
-
-#if defined(CONFIG_ETRAX_DEF_R_PORT_G24_DIR_OUT)
- or.d IO_STATE (R_GEN_CONFIG, g24dir, out),$r0
-#endif
-
move.d $r0,[genconfig_shadow] ; init a shadow register of R_GEN_CONFIG
move.d $r0,[R_GEN_CONFIG]
;; including their shadow registers
move.b CONFIG_ETRAX_DEF_R_PORT_PA_DIR,$r0
-#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_PA7)
- or.b IO_STATE (R_PORT_PA_DIR, dir7, output),$r0
-#endif
move.b $r0,[port_pa_dir_shadow]
move.b $r0,[R_PORT_PA_DIR]
move.b CONFIG_ETRAX_DEF_R_PORT_PA_DATA,$r0
-#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_PA7)
-#if defined(CONFIG_BLUETOOTH_RESET_ACTIVE_HIGH)
- and.b ~(1 << 7),$r0
-#else
- or.b (1 << 7),$r0
-#endif
-#endif
move.b $r0,[port_pa_data_shadow]
move.b $r0,[R_PORT_PA_DATA]
move.b $r0,[port_pb_config_shadow]
move.b $r0,[R_PORT_PB_CONFIG]
move.b CONFIG_ETRAX_DEF_R_PORT_PB_DIR,$r0
-#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_PB5)
- or.b IO_STATE (R_PORT_PB_DIR, dir5, output),$r0
-#endif
move.b $r0,[port_pb_dir_shadow]
move.b $r0,[R_PORT_PB_DIR]
move.b CONFIG_ETRAX_DEF_R_PORT_PB_DATA,$r0
-#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_PB5)
-#if defined(CONFIG_BLUETOOTH_RESET_ACTIVE_HIGH)
- and.b ~(1 << 5),$r0
-#else
- or.b (1 << 5),$r0
-#endif
-#endif
move.b $r0,[port_pb_data_shadow]
move.b $r0,[R_PORT_PB_DATA]
move.d $r0, [R_PORT_PB_I2C]
moveq 0,$r0
-#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_G10)
-#if defined(CONFIG_BLUETOOTH_RESET_ACTIVE_HIGH)
- and.d ~(1 << 10),$r0
-#else
- or.d (1 << 10),$r0
-#endif
-#endif
-#if defined(CONFIG_BLUETOOTH) && defined(CONFIG_BLUETOOTH_RESET_G11)
-#if defined(CONFIG_BLUETOOTH_RESET_ACTIVE_HIGH)
- and.d ~(1 << 11),$r0
-#else
- or.d (1 << 11),$r0
-#endif
-#endif
move.d $r0,[port_g_data_shadow]
move.d $r0,[R_PORT_G_DATA]
*R_MMU_KSEG = ( IO_STATE(R_MMU_KSEG, seg_f, seg ) | /* bootrom */
IO_STATE(R_MMU_KSEG, seg_e, page ) |
- IO_STATE(R_MMU_KSEG, seg_d, page ) |
- IO_STATE(R_MMU_KSEG, seg_c, page ) |
+ IO_STATE(R_MMU_KSEG, seg_d, page ) |
+ IO_STATE(R_MMU_KSEG, seg_c, page ) |
IO_STATE(R_MMU_KSEG, seg_b, seg ) | /* kernel reg area */
-#ifdef CONFIG_JULIETTE
- IO_STATE(R_MMU_KSEG, seg_a, seg ) | /* ARTPEC etc. */
-#else
IO_STATE(R_MMU_KSEG, seg_a, page ) |
-#endif
IO_STATE(R_MMU_KSEG, seg_9, seg ) | /* LED's on some boards */
IO_STATE(R_MMU_KSEG, seg_8, seg ) | /* CSE0/1, flash and I/O */
IO_STATE(R_MMU_KSEG, seg_7, page ) | /* kernel vmalloc area */
IO_FIELD(R_MMU_KBASE_HI, base_d, 0x0 ) |
IO_FIELD(R_MMU_KBASE_HI, base_c, 0x0 ) |
IO_FIELD(R_MMU_KBASE_HI, base_b, 0xb ) |
-#ifdef CONFIG_JULIETTE
- IO_FIELD(R_MMU_KBASE_HI, base_a, 0xa ) |
-#else
IO_FIELD(R_MMU_KBASE_HI, base_a, 0x0 ) |
-#endif
IO_FIELD(R_MMU_KBASE_HI, base_9, 0x9 ) |
IO_FIELD(R_MMU_KBASE_HI, base_8, 0x8 ) );
-
+
*R_MMU_KBASE_LO = ( IO_FIELD(R_MMU_KBASE_LO, base_7, 0x0 ) |
IO_FIELD(R_MMU_KBASE_LO, base_6, 0x4 ) |
IO_FIELD(R_MMU_KBASE_LO, base_5, 0x0 ) |
&ports[2];
#elif defined(CONFIG_ETRAX_DEBUG_PORT3)
&ports[3];
-#elif defined(CONFIG_ETRAX_DEBUG_PORT4)
- &ports[4];
#else
NULL;
#endif
;; For cramfs, partition starts with magic and length.
;; For jffs2, a jhead is prepended which contains with magic and length.
;; The jhead is not part of the jffs2 partition however.
-#ifndef CONFIG_ETRAXFS_SIM
move.d __bss_start, $r0
-#else
- move.d __end, $r0
-#endif
move.d [$r0], $r1
cmp.d CRAMFS_MAGIC, $r1 ; cramfs magic?
beq 2f ; yes, jump
#define IGNOREMASK (1 << (SER0_INTR_VECT - FIRST_IRQ))
#elif defined(CONFIG_ETRAX_KGDB_PORT1)
#define IGNOREMASK (1 << (SER1_INTR_VECT - FIRST_IRQ))
-#elif defined(CONFIG_ETRAX_KGB_PORT2)
+#elif defined(CONFIG_ETRAX_KGDB_PORT2)
#define IGNOREMASK (1 << (SER2_INTR_VECT - FIRST_IRQ))
#elif defined(CONFIG_ETRAX_KGDB_PORT3)
#define IGNOREMASK (1 << (SER3_INTR_VECT - FIRST_IRQ))
{I2C_BOARD_INFO("tmp100", 0x4E)},
#ifdef CONFIG_RTC_DRV_PCF8563
{I2C_BOARD_INFO("pcf8563", 0x51)},
-#endif
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- {I2C_BOARD_INFO("vgpio", 0x20)},
- {I2C_BOARD_INFO("vgpio", 0x21)},
#endif
{I2C_BOARD_INFO("pca9536", 0x41)},
{I2C_BOARD_INFO("fnp300", 0x40)},
{I2C_BOARD_INFO("tmp100", 0x4C)},
{I2C_BOARD_INFO("tmp100", 0x4D)},
{I2C_BOARD_INFO("tmp100", 0x4E)},
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
- {I2C_BOARD_INFO("vgpio", 0x20)},
- {I2C_BOARD_INFO("vgpio", 0x21)},
-#endif
{I2C_BOARD_INFO("pca9536", 0x41)},
{I2C_BOARD_INFO("fnp300", 0x40)},
{I2C_BOARD_INFO("fnp300", 0x42)},
Configures the initial data for the general port E bits. Most
products should use 00000 here.
-config ETRAX_DEF_GIO_PV_OE
- hex "GIO_PV_OE"
- depends on ETRAX_VIRTUAL_GPIO
- default "0000"
- help
- Configures the direction of virtual general port V bits. 1 is out,
- 0 is in. This is often totally different depending on the product
- used. These bits are used for all kinds of stuff. If you don't know
- what to use, it is always safe to put all as inputs, although
- floating inputs isn't good.
-
-config ETRAX_DEF_GIO_PV_OUT
- hex "GIO_PV_OUT"
- depends on ETRAX_VIRTUAL_GPIO
- default "0000"
- help
- Configures the initial data for the virtual general port V bits.
- Most products should use 0000 here.
-
endmenu
endif
#ifdef CONFIG_ETRAX_PB_LEDS
move.b $r2, [R_PORT_PB_DATA]
#endif
-#ifdef CONFIG_ETRAX_90000000_LEDS
- move.b $r2, [0x90000000]
-#endif
#endif
;; check if we got something on the serial port
assumed that we want to share code when debugging (exposes more
trouble). */
#ifndef SHARE_LIB_CORE
-# if (defined(__KERNEL__) || !defined(RELOC_DEBUG)) \
- && !defined(CONFIG_SHARE_SHLIB_CORE)
+# if (defined(__KERNEL__) || !defined(RELOC_DEBUG))
# define SHARE_LIB_CORE 0
# else
# define SHARE_LIB_CORE 1
* g1-g7 and g25-g31 is both input and outputs but on different pins
* Also note that some bits change pins depending on what interfaces
* are enabled.
- *
- * For ETRAX FS (CONFIG_ETRAXFS):
- * /dev/gpioa minor 0, 8 bit GPIO, each bit can change direction
- * /dev/gpiob minor 1, 18 bit GPIO, each bit can change direction
- * /dev/gpioc minor 3, 18 bit GPIO, each bit can change direction
- * /dev/gpiod minor 4, 18 bit GPIO, each bit can change direction
- * /dev/gpioe minor 5, 18 bit GPIO, each bit can change direction
- * /dev/leds minor 2, Access to leds depending on kernelconfig
- *
- * For ARTPEC-3 (CONFIG_CRIS_MACH_ARTPEC3):
- * /dev/gpioa minor 0, 32 bit GPIO, each bit can change direction
- * /dev/gpiob minor 1, 32 bit GPIO, each bit can change direction
- * /dev/gpioc minor 3, 16 bit GPIO, each bit can change direction
- * /dev/gpiod minor 4, 32 bit GPIO, input only
- * /dev/leds minor 2, Access to leds depending on kernelconfig
- * /dev/pwm0 minor 16, PWM channel 0 on PA30
- * /dev/pwm1 minor 17, PWM channel 1 on PA31
- * /dev/pwm2 minor 18, PWM channel 2 on PB26
- * /dev/ppwm minor 19, PPWM channel
- *
*/
#ifndef _ASM_ETRAXGPIO_H
#define _ASM_ETRAXGPIO_H
#define ETRAXGPIO_IOCTYPE 43
/* etraxgpio _IOC_TYPE, bits 8 to 15 in ioctl cmd */
-#ifdef CONFIG_ETRAX_ARCH_V10
#define GPIO_MINOR_A 0
#define GPIO_MINOR_B 1
#define GPIO_MINOR_LEDS 2
#define GPIO_MINOR_G 3
#define GPIO_MINOR_LAST 3
#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST
-#endif
-
-#ifdef CONFIG_ETRAXFS
-#define GPIO_MINOR_A 0
-#define GPIO_MINOR_B 1
-#define GPIO_MINOR_LEDS 2
-#define GPIO_MINOR_C 3
-#define GPIO_MINOR_D 4
-#define GPIO_MINOR_E 5
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-#define GPIO_MINOR_V 6
-#define GPIO_MINOR_LAST 6
-#else
-#define GPIO_MINOR_LAST 5
-#endif
-#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST
-#endif
-
-#ifdef CONFIG_CRIS_MACH_ARTPEC3
-#define GPIO_MINOR_A 0
-#define GPIO_MINOR_B 1
-#define GPIO_MINOR_LEDS 2
-#define GPIO_MINOR_C 3
-#define GPIO_MINOR_D 4
-#ifdef CONFIG_ETRAX_VIRTUAL_GPIO
-#define GPIO_MINOR_V 6
-#define GPIO_MINOR_LAST 6
-#else
-#define GPIO_MINOR_LAST 4
-#endif
-#define GPIO_MINOR_FIRST_PWM 16
-#define GPIO_MINOR_PWM0 (GPIO_MINOR_FIRST_PWM+0)
-#define GPIO_MINOR_PWM1 (GPIO_MINOR_FIRST_PWM+1)
-#define GPIO_MINOR_PWM2 (GPIO_MINOR_FIRST_PWM+2)
-#define GPIO_MINOR_PPWM (GPIO_MINOR_FIRST_PWM+3)
-#define GPIO_MINOR_LAST_PWM GPIO_MINOR_PPWM
-#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST_PWM
-#endif
-
/* supported ioctl _IOC_NR's */
#define IO_SETGET_OUTPUT 0x13 /* bits set in *arg is set to output, */
/* *arg updated with current output pins. */
-/* The following ioctl's are applicable to the PWM channels only */
-
-#define IO_PWM_SET_MODE 0x20
-
-enum io_pwm_mode {
- PWM_OFF = 0, /* disabled, deallocated */
- PWM_STANDARD = 1, /* 390 kHz, duty cycle 0..255/256 */
- PWM_FAST = 2, /* variable freq, w/ 10ns active pulse len */
- PWM_VARFREQ = 3, /* individually configurable high/low periods */
- PWM_SOFT = 4 /* software generated */
-};
-
-struct io_pwm_set_mode {
- enum io_pwm_mode mode;
-};
-
-/* Only for mode PWM_VARFREQ. Period lo/high set in increments of 10ns
- * from 10ns (value = 0) to 81920ns (value = 8191)
- * (Resulting frequencies range from 50 MHz (10ns + 10ns) down to
- * 6.1 kHz (81920ns + 81920ns) at 50% duty cycle, to 12.2 kHz at min/max duty
- * cycle (81920 + 10ns or 10ns + 81920ns, respectively).)
- */
-#define IO_PWM_SET_PERIOD 0x21
-
-struct io_pwm_set_period {
- unsigned int lo; /* 0..8191 */
- unsigned int hi; /* 0..8191 */
-};
-
-/* Only for modes PWM_STANDARD and PWM_FAST.
- * For PWM_STANDARD, set duty cycle of 390 kHz PWM output signal, from
- * 0 (value = 0) to 255/256 (value = 255).
- * For PWM_FAST, set duty cycle of PWM output signal from
- * 0% (value = 0) to 100% (value = 255). Output signal in this mode
- * is a 10ns pulse surrounded by a high or low level depending on duty
- * cycle (except for 0% and 100% which result in a constant output).
- * Resulting output frequency varies from 50 MHz at 50% duty cycle,
- * down to 390 kHz at min/max duty cycle.
- */
-#define IO_PWM_SET_DUTY 0x22
-
-struct io_pwm_set_duty {
- int duty; /* 0..255 */
-};
-
-/* Returns information about the latest PWM pulse.
- * lo: Length of the latest low period, in units of 10ns.
- * hi: Length of the latest high period, in units of 10ns.
- * cnt: Time since last detected edge, in units of 10ns.
- *
- * The input source to PWM is decied by IO_PWM_SET_INPUT_SRC.
- *
- * NOTE: All PWM devices is connected to the same input source.
- */
-#define IO_PWM_GET_PERIOD 0x23
-
-struct io_pwm_get_period {
- unsigned int lo;
- unsigned int hi;
- unsigned int cnt;
-};
-
-/* Sets the input source for the PWM input. For the src value see the
- * register description for gio:rw_pwm_in_cfg.
- *
- * NOTE: All PWM devices is connected to the same input source.
- */
-#define IO_PWM_SET_INPUT_SRC 0x24
-struct io_pwm_set_input_src {
- unsigned int src; /* 0..7 */
-};
-
-/* Sets the duty cycles in steps of 1/256, 0 = 0%, 255 = 100% duty cycle */
-#define IO_PPWM_SET_DUTY 0x25
-
-struct io_ppwm_set_duty {
- int duty; /* 0..255 */
-};
-
-/* Configuraton struct for the IO_PWMCLK_SET_CONFIG ioctl to configure
- * PWM capable gpio pins:
- */
-#define IO_PWMCLK_SETGET_CONFIG 0x26
-struct gpio_pwmclk_conf {
- unsigned int gpiopin; /* The pin number based on the opened device */
- unsigned int baseclk; /* The base clock to use, or sw will select one close*/
- unsigned int low; /* The number of low periods of the baseclk */
- unsigned int high; /* The number of high periods of the baseclk */
-};
-
-/* Examples:
- * To get a symmetric 12 MHz clock without knowing anything about the hardware:
- * baseclk = 12000000, low = 0, high = 0
- * To just get info of current setting:
- * baseclk = 0, low = 0, high = 0, the values will be updated by driver.
- */
-
#endif
projects / karo-tx-linux.git / commitdiff