Bjorn Helgaas [Tue, 3 Nov 2015 14:38:27 +0000 (08:38 -0600)]
Merge branches 'pci/host-altera', 'pci/host-designware', 'pci/host-generic', 'pci/host-imx6', 'pci/host-iproc', 'pci/host-mvebu', 'pci/host-rcar', 'pci/host-tegra' and 'pci/host-xgene' into next
* pci/host-altera:
PCI: altera: Add Altera PCIe MSI driver
PCI: altera: Add Altera PCIe host controller driver
ARM: Add msi.h to Kbuild
* pci/host-designware:
PCI: designware: Make "clocks" and "clock-names" optional DT properties
PCI: designware: Make driver arch-agnostic
ARM/PCI: Replace pci_sys_data->align_resource with global function pointer
PCI: designware: Use of_pci_get_host_bridge_resources() to parse DT
Revert "PCI: designware: Program ATU with untranslated address"
PCI: designware: Move calculation of bus addresses to DRA7xx
PCI: designware: Make "num-lanes" an optional DT property
PCI: designware: Require config accesses to be naturally aligned
PCI: designware: Simplify dw_pcie_cfg_read/write() interfaces
PCI: designware: Use exact access size in dw_pcie_cfg_read()
PCI: spear: Fix dw_pcie_cfg_read/write() usage
PCI: designware: Set up high part of MSI target address
PCI: designware: Make get_msi_addr() return phys_addr_t, not u32
PCI: designware: Implement multivector MSI IRQ setup
PCI: designware: Factor out MSI msg setup
PCI: Add msi_controller setup_irqs() method for special multivector setup
PCI: designware: Fix PORT_LOGIC_LINK_WIDTH_MASK
* pci/host-generic:
PCI: generic: Fix address window calculation for non-zero starting bus
PCI: generic: Pass starting bus number to pci_scan_root_bus()
PCI: generic: Allow multiple hosts with different map_bus() methods
arm64: dts: Drop linux,pci-probe-only from the Seattle DTS
powerpc/PCI: Fix lookup of linux,pci-probe-only property
PCI: generic: Fix lookup of linux,pci-probe-only property
of/pci: Add of_pci_check_probe_only to parse "linux,pci-probe-only"
* pci/host-imx6:
PCI: imx6: Add PCIE_PHY_RX_ASIC_OUT_VALID definition
PCI: imx6: Return real error code from imx6_add_pcie_port()
* pci/host-iproc:
PCI: iproc: Fix header comment "Corporation" misspelling
PCI: iproc: Add outbound mapping support
PCI: iproc: Update PCIe device tree bindings
PCI: iproc: Improve link detection logic
PCI: iproc: Fix PCIe reset logic
PCI: iproc: Call pci_fixup_irqs() for ARM64 as well as ARM
PCI: iproc: Remove unused struct iproc_pcie.irqs[]
PCI: iproc: Fix code comment to match code
* pci/host-mvebu:
PCI: mvebu: Remove code restricting accesses to slot 0
PCI: mvebu: Add PCI Express root complex capability block
PCI: mvebu: Improve clock/reset handling
PCI: mvebu: Use gpio_desc to carry around gpio
PCI: mvebu: Use devm_kcalloc() to allocate an array
PCI: mvebu: Use gpio_set_value_cansleep()
PCI: mvebu: Split port parsing and resource claiming from port setup
PCI: mvebu: Fix memory leaks and refcount leaks
PCI: mvebu: Move port parsing and resource claiming to separate function
PCI: mvebu: Use port->name rather than "PCIe%d.%d"
PCI: mvebu: Report full node name when reporting a DT error
PCI: mvebu: Use for_each_available_child_of_node() to walk child nodes
PCI: mvebu: Use of_get_available_child_count()
PCI: mvebu: Use exact config access size; don't read/modify/write
PCI: mvebu: Return zero for reserved or unimplemented config space
* pci/host-rcar:
PCI: rcar: Fix I/O offset for multiple host bridges
PCI: rcar: Set root bus nr to that provided in DT
PCI: rcar: Remove dependency on ARM-specific struct hw_pci
PCI: rcar: Make PCI aware of the I/O resources
PCI: rcar: Build pcie-rcar.c only on ARM
PCI: rcar: Build pci-rcar-gen2.c only on ARM
* pci/host-tegra:
PCI: tegra: Wrap static pgprot_t initializer with __pgprot()
Bjorn Helgaas [Mon, 2 Nov 2015 21:57:03 +0000 (15:57 -0600)]
Merge branches 'pci/aer', 'pci/hotplug', 'pci/misc', 'pci/msi', 'pci/resource' and 'pci/virtualization' into next
* pci/aer:
PCI/AER: Clear error status registers during enumeration and restore
* pci/hotplug:
PCI: pciehp: Queue power work requests in dedicated function
* pci/misc:
PCI: Turn off Request Attributes to avoid Chelsio T5 Completion erratum
x86/PCI: Make pci_subsys_init() static
PCI: Add builtin_pci_driver() to avoid registration boilerplate
PCI: Remove unnecessary "if" statement
* pci/msi:
x86/PCI: Don't alloc pcibios-irq when MSI is enabled
PCI/MSI: Export all remapped MSIs to sysfs attributes
PCI: Disable MSI on SiS 761
* pci/resource:
sparc/PCI: Add mem64 resource parsing for root bus
PCI: Expand Enhanced Allocation BAR output
PCI: Make Enhanced Allocation bitmasks more obvious
PCI: Handle Enhanced Allocation capability for SR-IOV devices
PCI: Add support for Enhanced Allocation devices
PCI: Add Enhanced Allocation register entries
PCI: Handle IORESOURCE_PCI_FIXED when assigning resources
PCI: Handle IORESOURCE_PCI_FIXED when sizing resources
PCI: Clear IORESOURCE_UNSET when reverting to firmware-assigned address
* pci/virtualization:
PCI: Fix sriov_enable() error path for pcibios_enable_sriov() failures
PCI: Wait 1 second between disabling VFs and clearing NumVFs
PCI: Reorder pcibios_sriov_disable()
PCI: Remove VFs in reverse order if virtfn_add() fails
PCI: Remove redundant validation of SR-IOV offset/stride registers
PCI: Set SR-IOV NumVFs to zero after enumeration
PCI: Enable SR-IOV ARI Capable Hierarchy before reading TotalVFs
PCI: Don't try to restore VF BARs
Zhou Wang [Fri, 30 Oct 2015 00:57:21 +0000 (19:57 -0500)]
PCI: designware: Make driver arch-agnostic
Previously, dw_pcie_host_init() created the PCI host bridge with
pci_common_init_dev(), an ARM-specific function that supplies the ARM-
specific pci_sys_data structure as the PCI "sysdata".
Make pcie-designware.c arch-agnostic by reimplementing the functionality of
pci_common_init_dev() directly in dw_pcie_host_init().
Note that this changes the bridge sysdata from the ARM pci_sys_data to the
DesignWare pcie_port structure. This doesn't affect the ARM sysdata users
because they are all specific to non-DesignWare host bridges, which will
still have pci_sys_data.
[bhelgaas: changelog] Tested-by: James Morse <james.morse@arm.com> Tested-by: Gabriel Fernandez <gabriel.fernandez@st.com> Tested-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com> Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Gabriele Paoloni [Fri, 30 Oct 2015 00:57:14 +0000 (19:57 -0500)]
ARM/PCI: Replace pci_sys_data->align_resource with global function pointer
dw_pcie_host_init() creates the PCI host bridge with pci_common_init_dev(),
an ARM-specific function that supplies the ARM-specific pci_sys_data
structure as the PCI "sysdata". To use dw_pcie_host_init() on other
architectures, we will copy the internals of pci_common_init_dev() into
pcie-designware.c instead of calling it, and dw_pcie_host_init() will
supply the DesignWare pcie_port structure as "sysdata".
Most ARM "sysdata" users are specific to non-DesignWare host bridges;
they'll be unaffected because those bridges will continue to have the ARM
pci_sys_data. Most of the rest are ARM-generic functions called by
pci_common_init_dev(); these will be unaffected because dw_pcie_host_init()
will no longer call pci_common_init().
But the ARM pcibios_align_resource() can be called by the PCI core for any
bridge, so it can't depend on sysdata since it may be either pci_sys_data
or pcie_port.
Remove the pcibios_align_resource() dependency on sysdata by replacing the
pci_sys_data->align_resource pointer with a global function pointer.
This is less general (we can no longer have per-host bridge
align_resource() methods), but the pci_sys_data->align_resource pointer was
used only by Marvell (see mvebu_pcie_enable()), so this would only be a
problem if we had a system with a combination of Marvell and other host
bridges
Zhou Wang [Fri, 30 Oct 2015 00:56:58 +0000 (19:56 -0500)]
Revert "PCI: designware: Program ATU with untranslated address"
Revert f4c55c5a3f7f ("PCI: designware: Program ATU with untranslated
address").
Note that dra7xx_pcie_host_init() now modifies pp->io_base, but we still
need the original value for dw_pcie_setup() in the path below, so this adds
a new io_base_tmp member. It will be removed later when dw_pcie_setup() is
removed.
Gabriele Paoloni [Fri, 30 Oct 2015 00:56:51 +0000 (19:56 -0500)]
PCI: designware: Move calculation of bus addresses to DRA7xx
Commit f4c55c5a3f7f ("PCI: designware: Program ATU with untranslated
address") added the calculation of PCI bus addresses in pcie-designware.c,
storing them in new fields added in struct pcie_port. This calculation is
done for every DesignWare user even though it only applies to DRA7xx.
Move the calculation of the bus addresses to the DRA7xx driver to allow the
rework of DesignWare to use the new DT parsing API.
PCI: designware: Make "num-lanes" an optional DT property
Currently "num-lanes" is read in dw_pcie_host_init(), but it is only used
if we call dw_pcie_setup_rc() while bringing up the link. If the link has
already been brought up by firmware, we need not call dw_pcie_setup_rc(),
and "num-lanes" is unnecessary.
Only complain about "num-lanes" if we actually need it and we didn't find a
valid value.
PCI: designware: Require config accesses to be naturally aligned
Add sanity checks on "addr" input parameter in dw_pcie_cfg_read() and
dw_pcie_cfg_write(). These checks make sure that accesses are aligned on
their size, e.g., a 4-byte config access is aligned on a 4-byte boundary.
Callers of dw_pcie_cfg_read() and dw_pcie_cfg_write() previously had to
split the address into "addr" and "where". The callees assumed "addr" was
32-bit aligned (with zeros in the low two bits) and they used only the low
two bits of "where".
Accept the entire address in "addr" and drop the now-redundant "where"
argument. As an example, this replaces this:
int dw_pcie_cfg_read(void __iomem *addr, int where, int size, u32 *val)
*val = readb(addr + (where & 1));
with this:
int dw_pcie_cfg_read(void __iomem *addr, int size, u32 *val)
*val = readb(addr):
[bhelgaas: changelog, split access size change to separate patch] Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI: designware: Use exact access size in dw_pcie_cfg_read()
dw_pcie_cfg_write() uses the exact 8-, 16-, or 32-bit access size
requested, but dw_pcie_cfg_read() previously performed a 32-bit read and
masked out the bits requested.
Use the exact access size in dw_pcie_cfg_read(). For example, if we want
an 8-bit read, use readb() instead of using readl() and masking out the 8
bits we need. This makes it symmetric with dw_pcie_cfg_write().
[bhelgaas: split into separate patch, set *val = 0 in failure case] Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The first argument of dw_pcie_cfg_read/write() is a 32-bit aligned address.
The second argument is the byte offset into a 32-bit word, and
dw_pcie_cfg_read/write() only look at the low two bits.
SPEAr13xx used dw_pcie_cfg_read() and dw_pcie_cfg_write() incorrectly: it
passed important address bits in the second argument, where they were
ignored.
Pass the complete 32-bit word address in the first argument and only the
2-bit offset into that word in the second argument.
Without this fix, SPEAr13xx host will never work with few buggy gen1 card
which connects with only gen1 host and also with any endpoint which would
generate a read request of more than 128 bytes.
Alexander Duyck [Thu, 29 Oct 2015 21:21:20 +0000 (16:21 -0500)]
PCI: Fix sriov_enable() error path for pcibios_enable_sriov() failures
Disable VFs if pcibios_enable_sriov() fails, just like we do for other
errors in sriov_enable(). Call pcibios_sriov_disable() if virtfn_add()
fails.
[bhelgaas: changelog, split to separate patch for reviewability] Fixes: 995df527f399 ("PCI: Add pcibios_sriov_enable() and pcibios_sriov_disable()") Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Alexander Duyck [Thu, 29 Oct 2015 21:21:16 +0000 (16:21 -0500)]
PCI: Wait 1 second between disabling VFs and clearing NumVFs
Per sec 3.3.3.1 of the SR-IOV spec, r1.1, we must allow 1.0s after clearing
VF Enable before reading any field in the SR-IOV Extended Capability.
Wait 1 second before calling pci_iov_set_numvfs(), which reads
PCI_SRIOV_VF_OFFSET and PCI_SRIOV_VF_STRIDE after it sets PCI_SRIOV_NUM_VF.
[bhelgaas: split to separate patch for reviewability, add spec reference] Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Alexander Duyck [Thu, 29 Oct 2015 21:21:11 +0000 (16:21 -0500)]
PCI: Reorder pcibios_sriov_disable()
Move pcibios_sriov_disable() up so it's defined before a future use.
[bhelgaas: split to separate patch for reviewability] Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Alexander Duyck [Thu, 29 Oct 2015 21:21:05 +0000 (16:21 -0500)]
PCI: Remove VFs in reverse order if virtfn_add() fails
If virtfn_add() fails, we call virtfn_remove() for any previously added
devices. Remove the devices in reverse order (first-added is
last-removed), which is more natural and doesn't require an additional
variable.
[bhelgaas: changelog, split to separate patch for reviewability] Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Phil Edworthy [Fri, 2 Oct 2015 10:25:06 +0000 (11:25 +0100)]
PCI: rcar: Set root bus nr to that provided in DT
On ARM64, setting the root bus number to -1 causes probe failure.
Moreover, we should use the bus number specified in the DT as we could have
multiple PCIe controllers with different bus ranges.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Simon Horman <horms+renesas@verge.net.au>
Phil Edworthy [Fri, 2 Oct 2015 10:25:05 +0000 (11:25 +0100)]
PCI: rcar: Remove dependency on ARM-specific struct hw_pci
The R-Car PCIe host controller driver uses pci_common_init_dev(), which is
ARM-specific and requires the ARM struct hw_pci. The part of
pci_common_init_dev() that is needed is limited and can be done here
without using hw_pci.
Note that the ARM pcibios functions expect the PCI sysdata to be a pointer
to a struct pci_sys_data. Add a struct pci_sys_data as the first element
in struct gen_pci so that when we use a gen_pci pointer as sysdata, it is
also a pointer to a struct pci_sys_data.
Create and scan the root bus directly without using the ARM
pci_common_init_dev() interface.
Based on 499733e0cc1a ("PCI: generic: Remove dependency on ARM-specific
struct hw_pci").
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Simon Horman <horms+renesas@verge.net.au>
The pcie-rcar.c driver (controlled by PCI_RCAR_GEN2_PCIE) uses struct
pci_sys_data and pci_ioremap_io(), which only exist on ARM. Building it on
other arches, e.g., arm64/shmobile, causes errors like this:
drivers/pci/host/pcie-rcar.c:138:52: warning: 'struct pci_sys_data' declared inside parameter list
drivers/pci/host/pcie-rcar.c:380:4: error: implicit declaration of function 'pci_ioremap_io' [-Werror=implicit-function-declaration]
Build pcie-rcar.c only on ARM.
[bhelgaas: changelog, split to separate pci-rcar-gen2 from pcie-rcar] Reported-by: Wolfram Sang <wsa@the-dreams.de> (pci_ioremap_io()) Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci-rcar-gen2.c driver (controlled by PCI_RCAR_GEN2) uses struct
pci_sys_data, which only exists on ARM. Building it on other arches, e.g.,
arm64/shmobile, causes errors like this:
drivers/pci/host/pci-rcar-gen2.c: In function 'rcar_pci_cfg_base': drivers/pci/host/pci-rcar-gen2.c:112:34: error: dereferencing pointer to incomplete type
struct rcar_pci_priv *priv = sys->private_data;
^
Build pci-rcar-gen2.c only on ARM.
[bhelgaas: changelog, split to separate pci-rcar-gen2 from pcie-rcar] Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Yinghai Lu [Tue, 20 Oct 2015 16:36:53 +0000 (11:36 -0500)]
sparc/PCI: Add mem64 resource parsing for root bus
David reported that a T5-8 sparc system failed to boot with:
pci_sun4v f02dbcfc: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x804000000000-0x80400fffffff] (bus address [0x0000-0xfffffff])
pci_bus 0000:00: root bus resource [mem 0x800000000000-0x80007effffff] (bus address [0x00000000-0x7effffff])
pci 0000:00:01.0: can't claim BAR 15 [mem 0x100000000-0x4afffffff pref]: no compatible bridge window
Note that we don't know about a host bridge aperture that contains
BAR 15. OF does report a MEM64 aperture, but before this patch,
pci_determine_mem_io_space() ignored it.
Add support for host bridge apertures with 64-bit PCI addresses. Also
set IORESOURCE_MEM_64 for PCI device and bridge resources in PCI 64-bit
memory space.
Sparc doesn't actually print the device and bridge resources, but after
this patch, we should have the equivalent of this:
pci_sun4v f02dbcfc: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x804000000000-0x80400fffffff] (bus address [0x0000-0xfffffff])
pci_bus 0000:00: root bus resource [mem 0x800000000000-0x80007effffff] (bus address [0x00000000-0x7effffff])
pci_bus 0000:00: root bus resource [mem 0x800100000000-0x8007ffffffff] (bus address [0x100000000-0x7ffffffff])
pci 0000:00:01.0: bridge window [mem 0x800100000000-0x8004afffffff 64bit pref]
[bhelgaas: changelog, URL to David's report] Fixes: d63e2e1f3df9 ("sparc/PCI: Clip bridge windows to fit in upstream windows") Link: http://lkml.kernel.org/r/5514391F.2030300@oracle.com Reported-by: David Ahern <david.ahern@oracle.com> Tested-by: David Ahern <david.ahern@oracle.com> Tested-by: Khalid Aziz <khalid.aziz@oracle.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Bjorn Helgaas [Thu, 29 Oct 2015 22:35:40 +0000 (17:35 -0500)]
PCI: Expand Enhanced Allocation BAR output
An Enhanced Allocation Capability entry with BEI 0 fills in
dev->resource[0] just like a real BAR 0 would, but non-EA experts might not
connect "EA - BEI 0" with BAR 0.
Decode the EA jargon a little bit, e.g., change this:
pci 0002:01:00.0: EA - BEI 0, Prop 0x00: [mem 0x84300000-0x84303fff]
Bjorn Helgaas [Thu, 29 Oct 2015 22:35:40 +0000 (17:35 -0500)]
PCI: Make Enhanced Allocation bitmasks more obvious
Expand bitmask #defines completely. This puts the shift in the code
instead of in the #define, but it makes it more obvious in the header file
how fields in the register are laid out.
David Daney [Thu, 29 Oct 2015 22:35:40 +0000 (17:35 -0500)]
PCI: Handle Enhanced Allocation capability for SR-IOV devices
SR-IOV BARs can be specified via EA entries. Extend the EA parser to
extract the SRIOV BAR resources, and modify sriov_init() to use resources
previously obtained via EA.
Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Sean O. Stalley <sean.stalley@intel.com>
Sean O. Stalley [Thu, 29 Oct 2015 22:35:39 +0000 (17:35 -0500)]
PCI: Add support for Enhanced Allocation devices
Add support for devices using Enhanced Allocation entries instead of BARs.
This allows the kernel to parse the EA Extended Capability structure in PCI
config space and claim the BAR-equivalent resources.
See https://pcisig.com/sites/default/files/specification_documents/ECN_Enhanced_Allocation_23_Oct_2014_Final.pdf
[bhelgaas: add spec URL, s/pci_ea_set_flags/pci_ea_flags/, consolidate
declarations, print unknown property in hex to match spec] Signed-off-by: Sean O. Stalley <sean.stalley@intel.com>
[david.daney@cavium.com: Add more support/checking for Entry Properties,
allow EA behind bridges, rewrite some error messages.] Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Sean O. Stalley [Thu, 29 Oct 2015 22:35:39 +0000 (17:35 -0500)]
PCI: Add Enhanced Allocation register entries
Add registers defined in PCI-SIG's Enhanced allocation ECN.
[bhelgaas: s/WRITEABLE/WRITABLE] Signed-off-by: Sean O. Stalley <sean.stalley@intel.com>
[david.daney@cavium.com: Added more definitions for PCI_EA_BEI_*] Signed-off-by: Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
David Daney [Thu, 29 Oct 2015 22:35:39 +0000 (17:35 -0500)]
PCI: Handle IORESOURCE_PCI_FIXED when assigning resources
The new Enhanced Allocation (EA) capability support (patches to follow)
creates resources with the IORESOURCE_PCI_FIXED set. During resource
assignment in pci_bus_assign_resources(), IORESOURCE_PCI_FIXED resources
are not given a parent. This, in turn, causes pci_enable_resources() to
fail with a "not claimed" error.
So, in __pci_bus_assign_resources(), for IORESOURCE_PCI_FIXED resources,
try to request the resource from a parent bus.
Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Sean O. Stalley <sean.stalley@intel.com>
David Daney [Thu, 29 Oct 2015 22:35:39 +0000 (17:35 -0500)]
PCI: Handle IORESOURCE_PCI_FIXED when sizing resources
The new Enhanced Allocation (EA) capability support (patches to follow)
creates resources with the IORESOURCE_PCI_FIXED set. Since these resources
cannot be relocated or resized, their alignment is not really defined, and
it is therefore not specified. This causes a problem in pbus_size_mem()
where resources with unspecified alignment are disabled.
So, in pbus_size_mem() skip IORESOURCE_PCI_FIXED resources, instead of
disabling them.
[bhelgaas: folded in "flags & IORESOURCE_PCI_FIXED" fix from David] Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Sean O. Stalley <sean.stalley@intel.com>
Alexander Duyck [Thu, 29 Oct 2015 21:20:57 +0000 (16:20 -0500)]
PCI: Remove redundant validation of SR-IOV offset/stride registers
Previously, we read, validated, and cached PCI_SRIOV_VF_OFFSET and
PCI_SRIOV_VF_STRIDE in sriov_enable(). But sriov_init() now does
that via compute_max_vf_buses(), so we don't need to do it again.
Remove the PCI_SRIOV_VF_OFFSET and PCI_SRIOV_VF_STRIDE config reads from
sriov_enable(). The pci_sriov structure already contains the offset and
stride corresponding to the current NumVFs.
[bhelgaas: split to separate patch for reviewability] Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Alexander Duyck [Thu, 29 Oct 2015 21:20:50 +0000 (16:20 -0500)]
PCI: Set SR-IOV NumVFs to zero after enumeration
The enumeration path should leave NumVFs set to zero. But after 4449f079722c ("PCI: Calculate maximum number of buses required for VFs"),
we call virtfn_max_buses() in the enumeration path, which changes NumVFs.
This NumVFs change is visible via lspci and sysfs until a driver enables
SR-IOV.
Iterate from TotalVFs down to zero so NumVFs is zero when we're finished
computing the maximum number of buses. Validate offset and stride in
the loop, so we can test it at every possible NumVFs setting. Rename
virtfn_max_buses() to compute_max_vf_buses() to hint that it does have a
side effect of updating iov->max_VF_buses.
[bhelgaas: changelog, rename, allow numVF==1 && stride==0, rework loop,
reverse sense of error path] Fixes: 4449f079722c ("PCI: Calculate maximum number of buses required for VFs") Based-on-patch-by: Ethan Zhao <ethan.zhao@oracle.com> Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Ben Shelton [Thu, 29 Oct 2015 21:20:31 +0000 (16:20 -0500)]
PCI: Enable SR-IOV ARI Capable Hierarchy before reading TotalVFs
For some SR-IOV devices, the number of available virtual functions, i.e.,
TotalVFs, increases after setting the ARI Capable Hierarchy bit in the
SR-IOV Control register. This violates the SR-IOV spec, r1.1, sec 3.3.6,
which says TotalVFs is HwInit, but we don't need TotalVFs before setting
the ARI Capable bit anyway.
Set the ARI Capable Hierarchy bit (if ARI is enabled in the upstream
bridge) before reading TotalVFs.
[bhelgaas: changelog] Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI: Turn off Request Attributes to avoid Chelsio T5 Completion erratum
The Chelsio T5 has a PCIe compliance erratum that causes Malformed TLP or
Unexpected Completion errors in some systems, which may cause device access
timeouts.
Per PCIe r3.0, sec 2.2.9, "Completion headers must supply the same values
for the Attribute as were supplied in the header of the corresponding
Request, except as explicitly allowed when IDO is used."
Instead of copying the Attributes from the Request to the Completion, the
T5 always generates Completions with zero Attributes. The receiver of a
Completion whose Attributes don't match the Request may accept it (which
itself seems non-compliant based on sec 2.3.2), or it may handle it as a
Malformed TLP or an Unexpected Completion, which will probably lead to a
device access timeout.
Work around this by disabling "Relaxed Ordering" and "No Snoop" in the Root
Port so it always generate Requests with zero Attributes.
This does affect all other devices which are downstream of that Root Port,
but these are performance optimizations that should not make a functional
difference.
Note that Configuration Space accesses are never supposed to have TLP
Attributes, so we're safe waiting till after any Configuration Space
accesses to do the Root Port "fixup".
Based on original work by Casey Leedom <leedom@chelsio.com>
[bhelgaas: changelog, comments, rename to pci_find_pcie_root_port(), rework
to use pci_upstream_bridge() and check for Root Port device type, edit
diagnostics to clarify intent and devices affected] Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Guenter Roeck [Mon, 12 Oct 2015 19:10:12 +0000 (12:10 -0700)]
PCI: pciehp: Queue power work requests in dedicated function
Up to now, work items to be queued to be handled by pciehp_power_thread()
are allocated using kmalloc() in three different locations. If not needed,
kfree() is called to free the allocated data.
Introduce a separate function to allocate the work item and queue it, and
call it only if needed. This reduces code duplication and avoids having to
free memory if the work item does not need to get executed.
[bhelgaas: tweak "no memory" message, make pciehp_queue_power_work() static] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Joerg Roedel [Fri, 9 Oct 2015 10:23:34 +0000 (12:23 +0200)]
x86/PCI: Don't alloc pcibios-irq when MSI is enabled
The pcibios-irq and MSI both use dev->irq to store the IRQ number. While
the MSI code checks for that and frees the pcibios-irq before overwriting
dev->irq, the pcibios_alloc_irq() function does not.
Usually this is not a problem, as the pcibios-irq is allocated before probe
time of the device and the MSI IRQ is allocted from the driver's probe
path.
But there are PCI devices handled by the core kernel and not by a standard
PCI driver, like the AMD IOMMU for example. For the AMD IOMMU a normal PCI
device driver does not make sense, because a driver can be forcibly unbound
from its device, which is not a good idea for an IOMMU.
Nevertheless the PCI core code tries to match the PCI device implementing
the AMD IOMMU against drivers, and allocates/frees a pcibios IRQ every time
it tries out a new driver. This overwrites the dev->irq field set by
pci_enable_msi() and sets it to 0 in the end (because the probe fails and
the pcibios-irq is freed again).
On suspend/resume this breaks the kernel, because the IRQ descriptor for
IRQ 0 is NULL.
Fix this by not allocating a pcibios-irq when MSI is already active. This
also has the benefit, that a device claimed by the core kernel can not be
probed by a PCI driver later.
Reported-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jiang Liu <jiang.liu@linux.intel.com>
Ray Jui [Fri, 16 Oct 2015 13:18:24 +0000 (08:18 -0500)]
PCI: iproc: Add outbound mapping support
Certain SoCs require the PCIe outbound mapping to be configured in
software. Add support for those chips.
[jonmason: Use %pap format when printing size_t to avoid warnings in 32-bit
build.]
[arnd: Use div64_u64() instead of "%" to avoid __aeabi_uldivmod link error
in 32-bit build.] Signed-off-by: Ray Jui <rjui@broadcom.com> Signed-off-by: Jon Mason <jonmason@broadcom.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI/MSI: Export all remapped MSIs to sysfs attributes
irqbalance uses sysfs attributes to populate its internal database, which
is then used to bind the IRQ to the appropriate NUMA node.
On a device accepting multiple MSIs and with interrupt remapping enabled,
only the first IRQ entry is exported in the "msi_irqs" directory. This
results in irqbalance having no clue of the NUMA affinity for the extra
IRQs, so it can't bind them to the correct node.
Export all MSI interrupts as sysfs attributes when relevant.
David Daney [Thu, 8 Oct 2015 19:54:16 +0000 (12:54 -0700)]
PCI: generic: Fix address window calculation for non-zero starting bus
Make the offset from the beginning of the "reg" property be from the
starting bus number, rather than zero. Hoist the invariant size
calculation out of the mapping for loop.
Update host-generic-pci.txt to clarify the semantics of the "reg" property
with respect to non-zero starting bus numbers.
Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Rob Herring <robh@kernel.org>
Russell King [Sat, 3 Oct 2015 18:13:38 +0000 (19:13 +0100)]
PCI: mvebu: Remove code restricting accesses to slot 0
Now that we advertise a PCIe capability, the Linux PCI layer will not scan
the bus for devices other than in slot 0. This makes the work-around to
trap accesses to devices other than slot 0 unnecessary.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370) Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood) Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add a PCI Express root complex capability block so the PCI layer identifies
the bridge as a PCI Express device.
We expose this as a version 1 PCIe capability block, with slot support. We
disable the clock power management capability as this depends on boards
wiring the CLKREQ# signal.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370) Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood) Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Russell King [Sat, 3 Oct 2015 18:13:27 +0000 (19:13 +0100)]
PCI: mvebu: Improve clock/reset handling
Add an implementation to handle clock and reset handling that is compliant
with the PCIe specification. The clock should be running and stable for
100us prior to reset being released, and we should re-assert reset prior to
stopping the clock.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370) Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood) Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Russell King [Sat, 3 Oct 2015 18:13:22 +0000 (19:13 +0100)]
PCI: mvebu: Use gpio_desc to carry around gpio
Use a gpio_desc to carry around the gpio, so we can then make use of the
GPIOF_ACTIVE_LOW property rather than carrying that around as well. This
also avoids needing to use gpio_is_valid() to check whether we have a GPIO;
checking for a non-NULL descriptor is simpler.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370) Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood) Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Russell King [Sat, 3 Oct 2015 18:13:07 +0000 (19:13 +0100)]
PCI: mvebu: Split port parsing and resource claiming from port setup
Split the PCIe port DT parsing and resource claiming from setting up the
actual ports. This allows us to gather all the resources first, before
touching the hardware. This is important as some of these resources (such
as the GPIO for the PCIe reset) may defer probing.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370) Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood) Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Russell King [Sat, 3 Oct 2015 18:13:02 +0000 (19:13 +0100)]
PCI: mvebu: Fix memory leaks and refcount leaks
The mvebu PCI port parsing is weak due to:
1) allocations via kasprintf() were not cleaned up when we encounter an
error or decide to skip the port.
2) kasprintf() wasn't checked for failure.
3) of_get_named_gpio_flags() returns EPROBE_DEFER if the GPIO is not
present, not devm_gpio_request_one().
4) the of_node was not being put when terminating the loop.
Fix these oversights.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370) Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood) Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Russell King [Wed, 23 Sep 2015 17:17:53 +0000 (18:17 +0100)]
PCI: mvebu: Use port->name rather than "PCIe%d.%d"
Use the port->name string which we previously formatted when referring to
the name of a port, rather than manually creating the port name each time.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP) Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Russell King [Wed, 23 Sep 2015 17:17:48 +0000 (18:17 +0100)]
PCI: mvebu: Report full node name when reporting a DT error
If we have a missing required property, report the full node name rather
than a vague "PCIe DT node" statement. This allows the exact node in error
to be identified immediately.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP) Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Russell King [Wed, 23 Sep 2015 17:17:42 +0000 (18:17 +0100)]
PCI: mvebu: Use for_each_available_child_of_node() to walk child nodes
Rather than using for_each_child_of_node() and testing each child's
availability, use the for_each_available_child_of_node() helper instead.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP) Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Russell King [Wed, 23 Sep 2015 17:17:37 +0000 (18:17 +0100)]
PCI: mvebu: Use of_get_available_child_count()
Rather than open-coding of_get_available_child_count(), use the provided
helper instead.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP) Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Russell King [Wed, 23 Sep 2015 17:17:32 +0000 (18:17 +0100)]
PCI: mvebu: Use exact config access size; don't read/modify/write
The idea that you can arbitarily read 32-bits from PCI configuration space,
modify a sub-field (like the command register) and write it back without
consequence is deeply flawed.
Status registers (such as the status register, PCIe device status register,
etc) contain status bits which are read, write-one-to-clear.
What this means is that reading 32-bits from the command register,
modifying the command register, and then writing it back has the effect of
clearing any status bits that were indicating at that time. Same for the
PCIe device control register clearing bits in the PCIe device status
register.
Since the Armada chips support byte, 16-bit and 32-bit accesses to the
registers (unless otherwise stated) and the PCI configuration data register
does not specify otherwise, it seems logical that the chip can indeed
generate the proper configuration access cycles down to byte level.
Testing with an ASM1062 PCIe to SATA mini-PCIe card on Armada 388. PCIe
capability at 0x80, DevCtl at 0x88, DevSta at 0x8a.
[bhelgaas: changelog] Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP) Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Russell King [Wed, 23 Sep 2015 17:17:26 +0000 (18:17 +0100)]
PCI: mvebu: Return zero for reserved or unimplemented config space
PCI requires reads to reserved or unimplemented configuration space to
return zero and complete normally (see PCI r3.0, sec 6.1). However, the
root port software implementation was returning 0xfffffff and
PCIBIOS_BAD_REGISTER_NUMBER.
Return zero when reading reserved or unimplemented config space.
[bhelgaas: changelog] Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP) Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
David Daney [Thu, 8 Oct 2015 15:24:41 +0000 (10:24 -0500)]
PCI: generic: Pass starting bus number to pci_scan_root_bus()
If the bus is being configured with a bus-range that does not start at
zero, pass that starting bus number to pci_scan_root_bus(). Passing the
incorrect value of zero causes attempted config accesses outside of the
supported range, which cascades to an OOPs spew and eventual kernel panic.
Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Will Deacon <will.deacon@arm.com>
David Daney [Thu, 8 Oct 2015 15:15:10 +0000 (10:15 -0500)]
PCI: generic: Allow multiple hosts with different map_bus() methods
The generic driver kept a global struct pci_ops ("gen_pci_ops") which it
patched with the .map_bus() method appropriate for the bus device. This is
a problem when we have two different types of bus devices: the .map_bus()
method for the last device probed clobbers the method for previous devices.
The result is that only the last bus device probed has the correct
.map_bus(), and the others fail.
Move the struct pci_ops into the bus-specific structure and initialize a
pointer to it when the bus device is probed.
Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Will Deacon <will.deacon@arm.com>
Paul Gortmaker [Wed, 26 Aug 2015 00:25:37 +0000 (20:25 -0400)]
PCI: Add builtin_pci_driver() to avoid registration boilerplate
In f309d4443130 ("platform_device: better support builtin boilerplate
avoidance"), we introduced the builtin_driver() macro.
Here we use that support and extend it to PCI driver registration, so where
a driver is clearly non-modular and builtin-only, we can register it in a
similar fashion. Existing code that is clearly non-modular can be updated
with the simple mapping of
We've essentially cloned the former to make the latter, and taken out the
remove/module_exit parts since those never get used in a non-modular build
of the code.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
After 8d63bc7beaee ("PCI/MSI: pci-xgene-msi: Get rid of struct
msi_controller"), it is no longer required to assign msi_controller for
X-Gene PCIe host bridge to support MSI.
Remove this unnecessary code. This also avoids a warning message ("failed
to enable MSI") during boot.
Ray Jui [Wed, 16 Sep 2015 00:39:18 +0000 (17:39 -0700)]
PCI: iproc: Fix PCIe reset logic
The current reset logic does not always properly reset the device. For
example, in the case when the perst_b signal is already de-asserted in the
bootloader, the current reset logic fails to trigger a proper assert ->
de-assert reset sequence.
Fix the issue by always triggering the proper reset sequence.
Also explicitly select the desired reset source, i.e., perst_b, and reduce
the wait time after the device comes out of reset from 250 ms to 100 ms,
based on recommendation from the ASIC team.
Tested-by: Vladimir Dreizin <vdreizin@broadcom.com> Tested-by: Darren Edamura <dedamura@broadcom.com> Signed-off-by: Ray Jui <rjui@broadcom.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Vladimir Dreizin <vdreizin@broadcom.com> Reviewed-by: Trac Hoang <trhoang@broadcom.com> Reviewed-by: Scott Branden <sbranden@broadcom.com>
Ondrej Zary [Thu, 24 Sep 2015 22:02:07 +0000 (17:02 -0500)]
PCI: Disable MSI on SiS 761
MSI is broken on SiS 761 chipset at least on PC Chips A31G board. No
interrupts are delivered once MSI is enabled for a device. This causes
hang on X11 start with a nVidia card installed (with nouveau driver).
Disable MSI completely for this chipset.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
PCI: Clear IORESOURCE_UNSET when reverting to firmware-assigned address
If pci_assign_resource() fails to assign space for a BAR, we may restore
the BAR to whatever firmware left there at boot-time (this depends on
whether the arch implements pcibios_retrieve_fw_addr()). The messages we
print are not as useful as they could be:
pci 0000:00:01.0: BAR 15: assigned [mem 0xc0000000-0xc01fffff 64bit pref]
pci 0000:01:00.0: BAR 0: no space for [mem size 0x10000000 pref]
pci 0000:01:00.0: BAR 0: trying firmware assignment [mem size 0x10000000 pref]
pci 0000:01:00.0: BAR 0: [mem size 0x10000000 pref] conflicts with PCI Bus 0000:00 [mem 0xc0000000-0xffffffff window]
The last two lines should contain the actual BAR address, not the size.
Clear IORESOURCE_UNSET so we print the address. If requesting the
firmware-assigned resource fails, mark it IORESOURCE_UNSET again.
This is a cosmetic change to clarify the message: previously, if
pci_revert_fw_address() succeeded, pci_assign_resource() cleared
IORESOURCE_UNSET anyway, so this isn't really a functional change.
Zhen Lei [Thu, 10 Sep 2015 10:40:31 +0000 (18:40 +0800)]
PCI: Remove unnecessary "if" statement
In store_remove_id(), set the default return value to -ENODEV, and
overwrite it with the input buffer size if we find a matching list entry.
Then we don't need to test whether to return an error or the count.
No functional change.
[bhelgaas: changelog] Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Zhou Wang [Wed, 26 Aug 2015 03:17:34 +0000 (11:17 +0800)]
PCI: designware: Fix PORT_LOGIC_LINK_WIDTH_MASK
The value under PORT_LOGIC_LINK_WIDTH_MASK is 0x1, 0x2, 0x4, 0x8. In IP
v4.2, bits [16:8] are defined for NUM_OF_LANES. But in IP v4.4, bits[12:8]
are defined for NUM_OF_LANES, bits [16:13] are for other usages (bit 16 is
AUTO_LANE_FLIP_CTRL_EN, bits [15:13] are PRE_DET_LANE).
As there is no conflict about NUM_OF_LANES between v4.2 and v4.4, change
the mask value to avoid future problems.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Jingoo Han <jingoohan1@gmail.com>
Marc Zyngier [Fri, 4 Sep 2015 16:50:11 +0000 (17:50 +0100)]
arm64: dts: Drop linux,pci-probe-only from the Seattle DTS
The linux,pci-probe-only property mandates an argument to indicate whether
or not to engage the "probe-only" mode, but the Seattle DTS just provides a
naked property, which is illegal.
Also, it turns out that the board is perfectly happy without probe-only, so
let's drop this altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Marc Zyngier [Fri, 4 Sep 2015 16:50:10 +0000 (17:50 +0100)]
powerpc/PCI: Fix lookup of linux,pci-probe-only property
When find_and_init_phbs() looks for the probe-only property, it seems to
trust the firmware to be correctly written, and assumes that there is a
parameter to the property.
It is conceivable that the firmware could not be that perfect, and it could
expose this property naked (at least one arm64 platform seems to exhibit
this exact behaviour). The setup code the ends up making a decision based
on whatever the property pointer points to, which is likely to be junk.
Instead, switch to the common of_pci.c implementation that doesn't suffer
from this problem and ignore the property if the firmware couldn't make up
its mind.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Marc Zyngier [Fri, 4 Sep 2015 16:50:09 +0000 (17:50 +0100)]
PCI: generic: Fix lookup of linux,pci-probe-only property
When pci-host-generic looks for the probe-only property, it seems to trust
the DT to be correctly written, and assumes that there is a parameter to
the property.
Unfortunately, this is not always the case, and some firmware expose this
property naked. The driver ends up making a decision based on whatever the
property pointer points to, which is likely to be junk.
Switch to the common of_pci.c implementation that doesn't suffer from this
problem.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Will Deacon <will.deacon@arm.com>
Marc Zyngier [Fri, 4 Sep 2015 16:50:08 +0000 (17:50 +0100)]
of/pci: Add of_pci_check_probe_only to parse "linux,pci-probe-only"
Both pci-host-generic and Pseries parse the "linux,pci-probe-only" property
to engage the PCI_PROBE_ONLY mode, and both have a subtle bug that can be
triggered if the property has no parameter.
Provide a generic, safe implementation that can be used by both.
[bhelgaas: fold in #include <asm-generic/pci-bridge.h>] Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rob Herring <robh@kernel.org>
PCI/AER: Clear error status registers during enumeration and restore
AER errors might be recorded when powering-on devices. These errors can be
ignored, so firmware usually clears them before the OS enumerates devices.
However, firmware is not involved when devices are added via hotplug, so
the OS may discover power-up errors that should be ignored. The same may
happen when powering up devices when resuming after suspend.
Clear the AER error status registers during enumeration and resume.
Wei Yang [Wed, 29 Jul 2015 08:52:58 +0000 (16:52 +0800)]
PCI: Don't try to restore VF BARs
VF BARs are read-only zero, so updating VF BARs will not have any effect.
See the SR-IOV spec r1.1, sec 3.4.1.11.
Don't update VF BARs in pci_restore_bars().
This avoids spurious "BAR %d: error updating" messages that we see when
doing vfio pass-through after 6eb7018705de ("vfio-pci: Move idle devices to
D3hot power state").
Merge tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull CRIS updates from Jesper Nilsson:
"Mostly removal of old cruft of which we can use a generic version, or
fixes for code not commonly run in the cris port, but also additions
to enable some good debug"
* tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris: (25 commits)
CRISv10: delete unused lib/dmacopy.c
CRISv10: delete unused lib/old_checksum.c
CRIS: fix switch_mm() lockdep splat
CRISv32: enable LOCKDEP_SUPPORT
CRIS: add STACKTRACE_SUPPORT
CRISv32: annotate irq enable in idle loop
CRISv32: add support for irqflags tracing
CRIS: UAPI: use generic types.h
CRIS: UAPI: use generic shmbuf.h
CRIS: UAPI: use generic msgbuf.h
CRIS: UAPI: use generic socket.h
CRIS: UAPI: use generic sembuf.h
CRIS: UAPI: use generic sockios.h
CRIS: UAPI: use generic auxvec.h
CRIS: UAPI: use generic headers via Kbuild
CRIS: UAPI: fix elf.h export
CRIS: don't make asm/elf.h depend on asm/user.h
CRIS: UAPI: fix ptrace.h
CRISv32: Squash compile warnings for axisflashmap
CRISv32: Add GPIO driver to the default configs
...
Linus Torvalds [Wed, 27 May 2015 22:32:15 +0000 (15:32 -0700)]
blk: rq_data_dir() should not return a boolean
rq_data_dir() returns either READ or WRITE (0 == READ, 1 == WRITE), not
a boolean value.
Now, admittedly the "!= 0" doesn't really change the value (0 stays as
zero, 1 stays as one), but it's not only redundant, it confuses gcc, and
causes gcc to warn about the construct
switch (rq_data_dir(req)) {
case READ:
...
case WRITE:
...
that we have in a few drivers.
Now, the gcc warning is silly and stupid (it seems to warn not about the
switch value having a different type from the case statements, but about
_any_ boolean switch value), but in this case the code itself is silly
and stupid too, so let's just change it, and get rid of warnings like
this:
drivers/block/hd.c: In function ‘hd_request’:
drivers/block/hd.c:630:11: warning: switch condition has boolean value [-Wswitch-bool]
switch (rq_data_dir(req)) {
The odd '!= 0' came in when "cmd_flags" got turned into a "u64" in
commit 5953316dbf90 ("block: make rq->cmd_flags be 64-bit") and is
presumably because the old code (that just did a logical 'and' with 1)
would then end up making the type of rq_data_dir() be u64 too.
But if we want to retain the old regular integer type, let's just cast
the result to 'int' rather than use that rather odd '!= 0'.
Fix up the writeback plugging introduced in commit d353d7587d02
("writeback: plug writeback at a high level") that then caused problems
due to the unplug happening with a spinlock held.
* writeback-plugging:
writeback: plug writeback in wb_writeback() and writeback_inodes_wb()
Revert "writeback: plug writeback at a high level"
writeback: plug writeback in wb_writeback() and writeback_inodes_wb()
We had to revert the pluggin in writeback_sb_inodes() because the
wb->list_lock is held, but we could easily plug at a higher level before
taking that lock, and unplug after releasing it. This does that.
Chris will run performance numbers, just to verify that this approach is
comparable to the alternative (we could just drop and re-take the lock
around the blk_finish_plug() rather than these two commits.
I'd have preferred waiting for actual performance numbers before picking
one approach over the other, but I don't want to release rc1 with the
known "sleeping function called from invalid context" issue, so I'll
pick this cleanup version for now. But if the numbers show that we
really want to plug just at the writeback_sb_inodes() level, and we
should just play ugly games with the spinlock, we'll switch to that.
Cc: Chris Mason <clm@fb.com> Cc: Josef Bacik <jbacik@fb.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Neil Brown <neilb@suse.de> Cc: Jan Kara <jack@suse.cz> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I didn't notice this when merging the thermal code from Zhang, but his
merge (commit 5a924a07f882: "Merge branches 'thermal-core' and
'thermal-intel' of .git into next") of the thermal-core and
thermal-intel branches was wrong.
In thermal-core, commit 17e8351a7739 ("thermal: consistently use int for
temperatures") converted the thermal layer to use "int" for
temperatures.
But in parallel, in the thermal-intel branch commit d0a12625d2ff
("thermal: Add Intel PCH thermal driver") added support for the intel
PCH thermal sensor using the old interfaces that used "unsigned long"
pointers.
This resulted in warnings like this:
drivers/thermal/intel_pch_thermal.c:184:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_temp = pch_thermal_get_temp,
^
drivers/thermal/intel_pch_thermal.c:184:14: note: (near initialization for ‘tzd_ops.get_temp’)
drivers/thermal/intel_pch_thermal.c:186:19: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_trip_temp = pch_get_trip_temp,
^
drivers/thermal/intel_pch_thermal.c:186:19: note: (near initialization for ‘tzd_ops.get_trip_temp’)
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
revert "ocfs2/dlm: use list_for_each_entry instead of list_for_each"
mm/early_ioremap: add explicit #include of asm/early_ioremap.h
fs/seq_file: convert int seq_vprint/seq_printf/etc... returns to void
selftests: enhance membarrier syscall test
selftests: add membarrier syscall test
sys_membarrier(): system-wide memory barrier (generic, x86)
MODSIGN: fix a compilation warning in extract-cert
Merge tag 'ntb-4.3' of git://github.com/jonmason/ntb
Pull NTB fixes from Jon Mason:
"NTB bug and documentation fixes, new device IDs, performance
improvements, and adding a mailing list to MAINTAINERS for NTB"
* tag 'ntb-4.3' of git://github.com/jonmason/ntb:
NTB: Fix range check on memory window index
NTB: Improve index handling in B2B MW workaround
NTB: Fix documentation for ntb_peer_db_clear.
NTB: Fix documentation for ntb_link_is_up
NTB: Use unique DMA channels for TX and RX
NTB: Remove dma_sync_wait from ntb_async_rx
NTB: Clean up QP stats info
NTB: Make the transport list in order of discovery
NTB: Add PCI Device IDs for Broadwell Xeon
NTB: Add flow control to the ntb_netdev
NTB: Add list to MAINTAINERS
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"Second round of updates for the input subsystem.
This introduces two brand new touchscreen drivers (Colibri and
imx6ul_tsc), some small driver fixes, and we are no longer report
errors from evdev_flush() as users do not really have a way of
handling errors, error codes that we were returning were not on the
list of errors supposed to be returned by close(), and errors were
causing issues with one of older versions of systemd"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: imx_keypad - remove obsolete comment
Input: touchscreen - add imx6ul_tsc driver support
Input: Add touchscreen support for Colibri VF50
Input: i8042 - lower log level for "no controller" message
Input: evdev - do not report errors form flush()
Input: elants_i2c - extend the calibration timeout to 12 seconds
Input: sparcspkr - fix module autoload for OF platform drivers
Input: regulator-haptic - fix module autoload for OF platform driver
Input: pwm-beeper - fix module autoload for OF platform driver
Input: ab8500-ponkey - Fix module autoload for OF platform driver
Input: cyttsp - remove unnecessary MODULE_ALIAS()
Input: elan_i2c - add ACPI ID "ELAN1000"
projects / karo-tx-linux.git / log