2 # (C) Copyright 2000 - 2012
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC, ARM, MIPS and several other
29 processors, which can be installed in a boot ROM and used to
30 initialize and test the hardware or to download and run application
33 The development of U-Boot is closely related to Linux: some parts of
34 the source code originate in the Linux source tree, we have some
35 header files in common, and special provision has been made to
36 support booting of Linux images.
38 Some attention has been paid to make this software easily
39 configurable and extendable. For instance, all monitor commands are
40 implemented with the same call interface, so that it's very easy to
41 add new commands. Also, instead of permanently adding rarely used
42 code (for instance hardware test utilities) to the monitor, you can
43 load and run it dynamically.
49 In general, all boards for which a configuration option exists in the
50 Makefile have been tested to some extent and can be considered
51 "working". In fact, many of them are used in production systems.
53 In case of problems see the CHANGELOG and CREDITS files to find out
54 who contributed the specific port. The MAINTAINERS file lists board
57 Note: There is no CHANGELOG file in the actual U-Boot source tree;
58 it can be created dynamically from the Git log using:
66 In case you have questions about, problems with or contributions for
67 U-Boot you should send a message to the U-Boot mailing list at
68 <u-boot@lists.denx.de>. There is also an archive of previous traffic
69 on the mailing list - please search the archive before asking FAQ's.
70 Please see http://lists.denx.de/pipermail/u-boot and
71 http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
74 Where to get source code:
75 =========================
77 The U-Boot source code is maintained in the git repository at
78 git://www.denx.de/git/u-boot.git ; you can browse it online at
79 http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
81 The "snapshot" links on this page allow you to download tarballs of
82 any version you might be interested in. Official releases are also
83 available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
86 Pre-built (and tested) images are available from
87 ftp://ftp.denx.de/pub/u-boot/images/
93 - start from 8xxrom sources
94 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
96 - make it easier to add custom boards
97 - make it possible to add other [PowerPC] CPUs
98 - extend functions, especially:
99 * Provide extended interface to Linux boot loader
102 * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
103 - create ARMBoot project (http://sourceforge.net/projects/armboot)
104 - add other CPU families (starting with ARM)
105 - create U-Boot project (http://sourceforge.net/projects/u-boot)
106 - current project page: see http://www.denx.de/wiki/U-Boot
112 The "official" name of this project is "Das U-Boot". The spelling
113 "U-Boot" shall be used in all written text (documentation, comments
114 in source files etc.). Example:
116 This is the README file for the U-Boot project.
118 File names etc. shall be based on the string "u-boot". Examples:
120 include/asm-ppc/u-boot.h
122 #include <asm/u-boot.h>
124 Variable names, preprocessor constants etc. shall be either based on
125 the string "u_boot" or on "U_BOOT". Example:
127 U_BOOT_VERSION u_boot_logo
128 IH_OS_U_BOOT u_boot_hush_start
134 Starting with the release in October 2008, the names of the releases
135 were changed from numerical release numbers without deeper meaning
136 into a time stamp based numbering. Regular releases are identified by
137 names consisting of the calendar year and month of the release date.
138 Additional fields (if present) indicate release candidates or bug fix
139 releases in "stable" maintenance trees.
142 U-Boot v2009.11 - Release November 2009
143 U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
144 U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
150 /arch Architecture specific files
151 /arm Files generic to ARM architecture
152 /cpu CPU specific files
153 /arm720t Files specific to ARM 720 CPUs
154 /arm920t Files specific to ARM 920 CPUs
155 /at91 Files specific to Atmel AT91RM9200 CPU
156 /imx Files specific to Freescale MC9328 i.MX CPUs
157 /s3c24x0 Files specific to Samsung S3C24X0 CPUs
158 /arm925t Files specific to ARM 925 CPUs
159 /arm926ejs Files specific to ARM 926 CPUs
160 /arm1136 Files specific to ARM 1136 CPUs
161 /ixp Files specific to Intel XScale IXP CPUs
162 /pxa Files specific to Intel XScale PXA CPUs
163 /s3c44b0 Files specific to Samsung S3C44B0 CPUs
164 /sa1100 Files specific to Intel StrongARM SA1100 CPUs
165 /lib Architecture specific library files
166 /avr32 Files generic to AVR32 architecture
167 /cpu CPU specific files
168 /lib Architecture specific library files
169 /blackfin Files generic to Analog Devices Blackfin architecture
170 /cpu CPU specific files
171 /lib Architecture specific library files
172 /x86 Files generic to x86 architecture
173 /cpu CPU specific files
174 /lib Architecture specific library files
175 /m68k Files generic to m68k architecture
176 /cpu CPU specific files
177 /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
178 /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
179 /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
180 /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
181 /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
182 /lib Architecture specific library files
183 /microblaze Files generic to microblaze architecture
184 /cpu CPU specific files
185 /lib Architecture specific library files
186 /mips Files generic to MIPS architecture
187 /cpu CPU specific files
188 /mips32 Files specific to MIPS32 CPUs
189 /xburst Files specific to Ingenic XBurst CPUs
190 /lib Architecture specific library files
191 /nds32 Files generic to NDS32 architecture
192 /cpu CPU specific files
193 /n1213 Files specific to Andes Technology N1213 CPUs
194 /lib Architecture specific library files
195 /nios2 Files generic to Altera NIOS2 architecture
196 /cpu CPU specific files
197 /lib Architecture specific library files
198 /powerpc Files generic to PowerPC architecture
199 /cpu CPU specific files
200 /74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
201 /mpc5xx Files specific to Freescale MPC5xx CPUs
202 /mpc5xxx Files specific to Freescale MPC5xxx CPUs
203 /mpc8xx Files specific to Freescale MPC8xx CPUs
204 /mpc824x Files specific to Freescale MPC824x CPUs
205 /mpc8260 Files specific to Freescale MPC8260 CPUs
206 /mpc85xx Files specific to Freescale MPC85xx CPUs
207 /ppc4xx Files specific to AMCC PowerPC 4xx CPUs
208 /lib Architecture specific library files
209 /sh Files generic to SH architecture
210 /cpu CPU specific files
211 /sh2 Files specific to sh2 CPUs
212 /sh3 Files specific to sh3 CPUs
213 /sh4 Files specific to sh4 CPUs
214 /lib Architecture specific library files
215 /sparc Files generic to SPARC architecture
216 /cpu CPU specific files
217 /leon2 Files specific to Gaisler LEON2 SPARC CPU
218 /leon3 Files specific to Gaisler LEON3 SPARC CPU
219 /lib Architecture specific library files
220 /api Machine/arch independent API for external apps
221 /board Board dependent files
222 /common Misc architecture independent functions
223 /disk Code for disk drive partition handling
224 /doc Documentation (don't expect too much)
225 /drivers Commonly used device drivers
226 /examples Example code for standalone applications, etc.
227 /fs Filesystem code (cramfs, ext2, jffs2, etc.)
228 /include Header Files
229 /lib Files generic to all architectures
230 /libfdt Library files to support flattened device trees
231 /lzma Library files to support LZMA decompression
232 /lzo Library files to support LZO decompression
234 /post Power On Self Test
235 /rtc Real Time Clock drivers
236 /tools Tools to build S-Record or U-Boot images, etc.
238 Software Configuration:
239 =======================
241 Configuration is usually done using C preprocessor defines; the
242 rationale behind that is to avoid dead code whenever possible.
244 There are two classes of configuration variables:
246 * Configuration _OPTIONS_:
247 These are selectable by the user and have names beginning with
250 * Configuration _SETTINGS_:
251 These depend on the hardware etc. and should not be meddled with if
252 you don't know what you're doing; they have names beginning with
255 Later we will add a configuration tool - probably similar to or even
256 identical to what's used for the Linux kernel. Right now, we have to
257 do the configuration by hand, which means creating some symbolic
258 links and editing some configuration files. We use the TQM8xxL boards
262 Selection of Processor Architecture and Board Type:
263 ---------------------------------------------------
265 For all supported boards there are ready-to-use default
266 configurations available; just type "make <board_name>_config".
268 Example: For a TQM823L module type:
273 For the Cogent platform, you need to specify the CPU type as well;
274 e.g. "make cogent_mpc8xx_config". And also configure the cogent
275 directory according to the instructions in cogent/README.
278 Configuration Options:
279 ----------------------
281 Configuration depends on the combination of board and CPU type; all
282 such information is kept in a configuration file
283 "include/configs/<board_name>.h".
285 Example: For a TQM823L module, all configuration settings are in
286 "include/configs/TQM823L.h".
289 Many of the options are named exactly as the corresponding Linux
290 kernel configuration options. The intention is to make it easier to
291 build a config tool - later.
294 The following options need to be configured:
296 - CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
298 - Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
300 - CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
301 Define exactly one, e.g. CONFIG_ATSTK1002
303 - CPU Module Type: (if CONFIG_COGENT is defined)
304 Define exactly one of
306 --- FIXME --- not tested yet:
307 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
308 CONFIG_CMA287_23, CONFIG_CMA287_50
310 - Motherboard Type: (if CONFIG_COGENT is defined)
311 Define exactly one of
312 CONFIG_CMA101, CONFIG_CMA102
314 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
315 Define one or more of
318 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
319 Define one or more of
320 CONFIG_LCD_HEARTBEAT - update a character position on
321 the LCD display every second with
324 - Board flavour: (if CONFIG_MPC8260ADS is defined)
327 CONFIG_SYS_8260ADS - original MPC8260ADS
328 CONFIG_SYS_8266ADS - MPC8266ADS
329 CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
330 CONFIG_SYS_8272ADS - MPC8272ADS
332 - Marvell Family Member
333 CONFIG_SYS_MVFS - define it if you want to enable
334 multiple fs option at one time
335 for marvell soc family
337 - MPC824X Family Member (if CONFIG_MPC824X is defined)
338 Define exactly one of
339 CONFIG_MPC8240, CONFIG_MPC8245
341 - 8xx CPU Options: (if using an MPC8xx CPU)
342 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
343 get_gclk_freq() cannot work
344 e.g. if there is no 32KHz
345 reference PIT/RTC clock
346 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
349 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
350 CONFIG_SYS_8xx_CPUCLK_MIN
351 CONFIG_SYS_8xx_CPUCLK_MAX
352 CONFIG_8xx_CPUCLK_DEFAULT
353 See doc/README.MPC866
355 CONFIG_SYS_MEASURE_CPUCLK
357 Define this to measure the actual CPU clock instead
358 of relying on the correctness of the configured
359 values. Mostly useful for board bringup to make sure
360 the PLL is locked at the intended frequency. Note
361 that this requires a (stable) reference clock (32 kHz
362 RTC clock or CONFIG_SYS_8XX_XIN)
364 CONFIG_SYS_DELAYED_ICACHE
366 Define this option if you want to enable the
367 ICache only when Code runs from RAM.
372 Specifies that the core is a 64-bit PowerPC implementation (implements
373 the "64" category of the Power ISA). This is necessary for ePAPR
374 compliance, among other possible reasons.
376 CONFIG_SYS_FSL_TBCLK_DIV
378 Defines the core time base clock divider ratio compared to the
379 system clock. On most PQ3 devices this is 8, on newer QorIQ
380 devices it can be 16 or 32. The ratio varies from SoC to Soc.
382 CONFIG_SYS_FSL_PCIE_COMPAT
384 Defines the string to utilize when trying to match PCIe device
385 tree nodes for the given platform.
387 CONFIG_SYS_PPC_E500_DEBUG_TLB
389 Enables a temporary TLB entry to be used during boot to work
390 around limitations in e500v1 and e500v2 external debugger
391 support. This reduces the portions of the boot code where
392 breakpoints and single stepping do not work. The value of this
393 symbol should be set to the TLB1 entry to be used for this
396 CONFIG_SYS_FSL_ERRATUM_A004510
398 Enables a workaround for erratum A004510. If set,
399 then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
400 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.
402 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
403 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)
405 Defines one or two SoC revisions (low 8 bits of SVR)
406 for which the A004510 workaround should be applied.
408 The rest of SVR is either not relevant to the decision
409 of whether the erratum is present (e.g. p2040 versus
410 p2041) or is implied by the build target, which controls
411 whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.
413 See Freescale App Note 4493 for more information about
416 CONFIG_A003399_NOR_WORKAROUND
417 Enables a workaround for IFC erratum A003399. It is only
418 requred during NOR boot.
420 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
422 This is the value to write into CCSR offset 0x18600
423 according to the A004510 workaround.
425 CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
426 This value denotes start offset of M2 memory
427 which is directly connected to the DSP core.
429 CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
430 This value denotes start offset of DSP CCSR space.
432 - Generic CPU options:
433 CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
435 Defines the endianess of the CPU. Implementation of those
436 values is arch specific.
438 - Intel Monahans options:
439 CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
441 Defines the Monahans run mode to oscillator
442 ratio. Valid values are 8, 16, 24, 31. The core
443 frequency is this value multiplied by 13 MHz.
445 CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
447 Defines the Monahans turbo mode to oscillator
448 ratio. Valid values are 1 (default if undefined) and
449 2. The core frequency as calculated above is multiplied
453 CONFIG_SYS_INIT_SP_OFFSET
455 Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
456 pointer. This is needed for the temporary stack before
459 CONFIG_SYS_MIPS_CACHE_MODE
461 Cache operation mode for the MIPS CPU.
462 See also arch/mips/include/asm/mipsregs.h.
464 CONF_CM_CACHABLE_NO_WA
467 CONF_CM_CACHABLE_NONCOHERENT
471 CONF_CM_CACHABLE_ACCELERATED
473 CONFIG_SYS_XWAY_EBU_BOOTCFG
475 Special option for Lantiq XWAY SoCs for booting from NOR flash.
476 See also arch/mips/cpu/mips32/start.S.
478 CONFIG_XWAY_SWAP_BYTES
480 Enable compilation of tools/xway-swap-bytes needed for Lantiq
481 XWAY SoCs for booting from NOR flash. The U-Boot image needs to
482 be swapped if a flash programmer is used.
485 CONFIG_SYS_EXCEPTION_VECTORS_HIGH
487 Select high exception vectors of the ARM core, e.g., do not
488 clear the V bit of the c1 register of CP15.
490 CONFIG_SYS_THUMB_BUILD
492 Use this flag to build U-Boot using the Thumb instruction
493 set for ARM architectures. Thumb instruction set provides
494 better code density. For ARM architectures that support
495 Thumb2 this flag will result in Thumb2 code generated by
498 CONFIG_ARM_ERRATA_716044
499 CONFIG_ARM_ERRATA_742230
500 CONFIG_ARM_ERRATA_743622
501 CONFIG_ARM_ERRATA_751472
503 If set, the workarounds for these ARM errata are applied early
504 during U-Boot startup. Note that these options force the
505 workarounds to be applied; no CPU-type/version detection
506 exists, unlike the similar options in the Linux kernel. Do not
507 set these options unless they apply!
512 The frequency of the timer returned by get_timer().
513 get_timer() must operate in milliseconds and this CONFIG
514 option must be set to 1000.
516 - Linux Kernel Interface:
519 U-Boot stores all clock information in Hz
520 internally. For binary compatibility with older Linux
521 kernels (which expect the clocks passed in the
522 bd_info data to be in MHz) the environment variable
523 "clocks_in_mhz" can be defined so that U-Boot
524 converts clock data to MHZ before passing it to the
526 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
527 "clocks_in_mhz=1" is automatically included in the
530 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
532 When transferring memsize parameter to linux, some versions
533 expect it to be in bytes, others in MB.
534 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
538 New kernel versions are expecting firmware settings to be
539 passed using flattened device trees (based on open firmware
543 * New libfdt-based support
544 * Adds the "fdt" command
545 * The bootm command automatically updates the fdt
547 OF_CPU - The proper name of the cpus node (only required for
548 MPC512X and MPC5xxx based boards).
549 OF_SOC - The proper name of the soc node (only required for
550 MPC512X and MPC5xxx based boards).
551 OF_TBCLK - The timebase frequency.
552 OF_STDOUT_PATH - The path to the console device
554 boards with QUICC Engines require OF_QE to set UCC MAC
557 CONFIG_OF_BOARD_SETUP
559 Board code has addition modification that it wants to make
560 to the flat device tree before handing it off to the kernel
564 This define fills in the correct boot CPU in the boot
565 param header, the default value is zero if undefined.
569 U-Boot can detect if an IDE device is present or not.
570 If not, and this new config option is activated, U-Boot
571 removes the ATA node from the DTS before booting Linux,
572 so the Linux IDE driver does not probe the device and
573 crash. This is needed for buggy hardware (uc101) where
574 no pull down resistor is connected to the signal IDE5V_DD7.
576 CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
578 This setting is mandatory for all boards that have only one
579 machine type and must be used to specify the machine type
580 number as it appears in the ARM machine registry
581 (see http://www.arm.linux.org.uk/developer/machines/).
582 Only boards that have multiple machine types supported
583 in a single configuration file and the machine type is
584 runtime discoverable, do not have to use this setting.
586 - vxWorks boot parameters:
588 bootvx constructs a valid bootline using the following
589 environments variables: bootfile, ipaddr, serverip, hostname.
590 It loads the vxWorks image pointed bootfile.
592 CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
593 CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
594 CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
595 CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
597 CONFIG_SYS_VXWORKS_ADD_PARAMS
599 Add it at the end of the bootline. E.g "u=username pw=secret"
601 Note: If a "bootargs" environment is defined, it will overwride
602 the defaults discussed just above.
604 - Cache Configuration:
605 CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
606 CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
607 CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
609 - Cache Configuration for ARM:
610 CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
612 CONFIG_SYS_PL310_BASE - Physical base address of PL310
613 controller register space
618 Define this if you want support for Amba PrimeCell PL010 UARTs.
622 Define this if you want support for Amba PrimeCell PL011 UARTs.
626 If you have Amba PrimeCell PL011 UARTs, set this variable to
627 the clock speed of the UARTs.
631 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
632 define this to a list of base addresses for each (supported)
633 port. See e.g. include/configs/versatile.h
635 CONFIG_PL011_SERIAL_RLCR
637 Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
638 have separate receive and transmit line control registers. Set
639 this variable to initialize the extra register.
641 CONFIG_PL011_SERIAL_FLUSH_ON_INIT
643 On some platforms (e.g. U8500) U-Boot is loaded by a second stage
644 boot loader that has already initialized the UART. Define this
645 variable to flush the UART at init time.
649 Depending on board, define exactly one serial port
650 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
651 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
652 console by defining CONFIG_8xx_CONS_NONE
654 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
655 port routines must be defined elsewhere
656 (i.e. serial_init(), serial_getc(), ...)
659 Enables console device for a color framebuffer. Needs following
660 defines (cf. smiLynxEM, i8042)
661 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
663 VIDEO_HW_RECTFILL graphic chip supports
666 VIDEO_HW_BITBLT graphic chip supports
667 bit-blit (cf. smiLynxEM)
668 VIDEO_VISIBLE_COLS visible pixel columns
670 VIDEO_VISIBLE_ROWS visible pixel rows
671 VIDEO_PIXEL_SIZE bytes per pixel
672 VIDEO_DATA_FORMAT graphic data format
673 (0-5, cf. cfb_console.c)
674 VIDEO_FB_ADRS framebuffer address
675 VIDEO_KBD_INIT_FCT keyboard int fct
676 (i.e. i8042_kbd_init())
677 VIDEO_TSTC_FCT test char fct
679 VIDEO_GETC_FCT get char fct
681 CONFIG_CONSOLE_CURSOR cursor drawing on/off
682 (requires blink timer
684 CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
685 CONFIG_CONSOLE_TIME display time/date info in
687 (requires CONFIG_CMD_DATE)
688 CONFIG_VIDEO_LOGO display Linux logo in
690 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
691 linux_logo.h for logo.
692 Requires CONFIG_VIDEO_LOGO
693 CONFIG_CONSOLE_EXTRA_INFO
694 additional board info beside
697 When CONFIG_CFB_CONSOLE_ANSI is defined, console will support
698 a limited number of ANSI escape sequences (cursor control,
699 erase functions and limited graphics rendition control).
701 When CONFIG_CFB_CONSOLE is defined, video console is
702 default i/o. Serial console can be forced with
703 environment 'console=serial'.
705 When CONFIG_SILENT_CONSOLE is defined, all console
706 messages (by U-Boot and Linux!) can be silenced with
707 the "silent" environment variable. See
708 doc/README.silent for more information.
711 CONFIG_BAUDRATE - in bps
712 Select one of the baudrates listed in
713 CONFIG_SYS_BAUDRATE_TABLE, see below.
714 CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
716 - Console Rx buffer length
717 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
718 the maximum receive buffer length for the SMC.
719 This option is actual only for 82xx and 8xx possible.
720 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
721 must be defined, to setup the maximum idle timeout for
724 - Pre-Console Buffer:
725 Prior to the console being initialised (i.e. serial UART
726 initialised etc) all console output is silently discarded.
727 Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
728 buffer any console messages prior to the console being
729 initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ
730 bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is
731 a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ
732 bytes are output before the console is initialised, the
733 earlier bytes are discarded.
735 'Sane' compilers will generate smaller code if
736 CONFIG_PRE_CON_BUF_SZ is a power of 2
738 - Safe printf() functions
739 Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
740 the printf() functions. These are defined in
741 include/vsprintf.h and include snprintf(), vsnprintf() and
742 so on. Code size increase is approximately 300-500 bytes.
743 If this option is not given then these functions will
744 silently discard their buffer size argument - this means
745 you are not getting any overflow checking in this case.
747 - Boot Delay: CONFIG_BOOTDELAY - in seconds
748 Delay before automatically booting the default image;
749 set to -1 to disable autoboot.
750 set to -2 to autoboot with no delay and not check for abort
751 (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
753 See doc/README.autoboot for these options that
754 work with CONFIG_BOOTDELAY. None are required.
755 CONFIG_BOOT_RETRY_TIME
756 CONFIG_BOOT_RETRY_MIN
757 CONFIG_AUTOBOOT_KEYED
758 CONFIG_AUTOBOOT_PROMPT
759 CONFIG_AUTOBOOT_DELAY_STR
760 CONFIG_AUTOBOOT_STOP_STR
761 CONFIG_AUTOBOOT_DELAY_STR2
762 CONFIG_AUTOBOOT_STOP_STR2
763 CONFIG_ZERO_BOOTDELAY_CHECK
764 CONFIG_RESET_TO_RETRY
768 Only needed when CONFIG_BOOTDELAY is enabled;
769 define a command string that is automatically executed
770 when no character is read on the console interface
771 within "Boot Delay" after reset.
774 This can be used to pass arguments to the bootm
775 command. The value of CONFIG_BOOTARGS goes into the
776 environment value "bootargs".
778 CONFIG_RAMBOOT and CONFIG_NFSBOOT
779 The value of these goes into the environment as
780 "ramboot" and "nfsboot" respectively, and can be used
781 as a convenience, when switching between booting from
787 When this option is #defined, the existence of the
788 environment variable "preboot" will be checked
789 immediately before starting the CONFIG_BOOTDELAY
790 countdown and/or running the auto-boot command resp.
791 entering interactive mode.
793 This feature is especially useful when "preboot" is
794 automatically generated or modified. For an example
795 see the LWMON board specific code: here "preboot" is
796 modified when the user holds down a certain
797 combination of keys on the (special) keyboard when
800 - Serial Download Echo Mode:
802 If defined to 1, all characters received during a
803 serial download (using the "loads" command) are
804 echoed back. This might be needed by some terminal
805 emulations (like "cu"), but may as well just take
806 time on others. This setting #define's the initial
807 value of the "loads_echo" environment variable.
809 - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
811 Select one of the baudrates listed in
812 CONFIG_SYS_BAUDRATE_TABLE, see below.
815 Monitor commands can be included or excluded
816 from the build by using the #include files
817 <config_cmd_all.h> and #undef'ing unwanted
818 commands, or using <config_cmd_default.h>
819 and augmenting with additional #define's
822 The default command configuration includes all commands
823 except those marked below with a "*".
825 CONFIG_CMD_ASKENV * ask for env variable
826 CONFIG_CMD_BDI bdinfo
827 CONFIG_CMD_BEDBUG * Include BedBug Debugger
828 CONFIG_CMD_BMP * BMP support
829 CONFIG_CMD_BSP * Board specific commands
830 CONFIG_CMD_BOOTD bootd
831 CONFIG_CMD_CACHE * icache, dcache
832 CONFIG_CMD_CONSOLE coninfo
833 CONFIG_CMD_CRC32 * crc32
834 CONFIG_CMD_DATE * support for RTC, date/time...
835 CONFIG_CMD_DHCP * DHCP support
836 CONFIG_CMD_DIAG * Diagnostics
837 CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
838 CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
839 CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
840 CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
841 CONFIG_CMD_DTT * Digital Therm and Thermostat
842 CONFIG_CMD_ECHO echo arguments
843 CONFIG_CMD_EDITENV edit env variable
844 CONFIG_CMD_EEPROM * EEPROM read/write support
845 CONFIG_CMD_ELF * bootelf, bootvx
846 CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
847 CONFIG_CMD_ENV_FLAGS * display details about env flags
848 CONFIG_CMD_EXPORTENV * export the environment
849 CONFIG_CMD_EXT2 * ext2 command support
850 CONFIG_CMD_EXT4 * ext4 command support
851 CONFIG_CMD_SAVEENV saveenv
852 CONFIG_CMD_FDC * Floppy Disk Support
853 CONFIG_CMD_FAT * FAT command support
854 CONFIG_CMD_FDOS * Dos diskette Support
855 CONFIG_CMD_FLASH flinfo, erase, protect
856 CONFIG_CMD_FPGA FPGA device initialization support
857 CONFIG_CMD_FUSE * Device fuse support
858 CONFIG_CMD_GETTIME * Get time since boot
859 CONFIG_CMD_GO * the 'go' command (exec code)
860 CONFIG_CMD_GREPENV * search environment
861 CONFIG_CMD_HASH * calculate hash / digest
862 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
863 CONFIG_CMD_I2C * I2C serial bus support
864 CONFIG_CMD_IDE * IDE harddisk support
865 CONFIG_CMD_IMI iminfo
866 CONFIG_CMD_IMLS List all images found in NOR flash
867 CONFIG_CMD_IMLS_NAND * List all images found in NAND flash
868 CONFIG_CMD_IMMAP * IMMR dump support
869 CONFIG_CMD_IMPORTENV * import an environment
870 CONFIG_CMD_INI * import data from an ini file into the env
871 CONFIG_CMD_IRQ * irqinfo
872 CONFIG_CMD_ITEST Integer/string test of 2 values
873 CONFIG_CMD_JFFS2 * JFFS2 Support
874 CONFIG_CMD_KGDB * kgdb
875 CONFIG_CMD_LDRINFO * ldrinfo (display Blackfin loader)
876 CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
878 CONFIG_CMD_LOADB loadb
879 CONFIG_CMD_LOADS loads
880 CONFIG_CMD_MD5SUM * print md5 message digest
881 (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
882 CONFIG_CMD_MEMINFO * Display detailed memory information
883 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
885 CONFIG_CMD_MEMTEST * mtest
886 CONFIG_CMD_MISC Misc functions like sleep etc
887 CONFIG_CMD_MMC * MMC memory mapped support
888 CONFIG_CMD_MII * MII utility commands
889 CONFIG_CMD_MTDPARTS * MTD partition support
890 CONFIG_CMD_NAND * NAND support
891 CONFIG_CMD_NET bootp, tftpboot, rarpboot
892 CONFIG_CMD_NFS NFS support
893 CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
894 CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
895 CONFIG_CMD_PCI * pciinfo
896 CONFIG_CMD_PCMCIA * PCMCIA support
897 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
899 CONFIG_CMD_PORTIO * Port I/O
900 CONFIG_CMD_READ * Read raw data from partition
901 CONFIG_CMD_REGINFO * Register dump
902 CONFIG_CMD_RUN run command in env variable
903 CONFIG_CMD_SANDBOX * sb command to access sandbox features
904 CONFIG_CMD_SAVES * save S record dump
905 CONFIG_CMD_SCSI * SCSI Support
906 CONFIG_CMD_SDRAM * print SDRAM configuration information
907 (requires CONFIG_CMD_I2C)
908 CONFIG_CMD_SETGETDCR Support for DCR Register access
910 CONFIG_CMD_SF * Read/write/erase SPI NOR flash
911 CONFIG_CMD_SHA1SUM * print sha1 memory digest
912 (requires CONFIG_CMD_MEMORY)
913 CONFIG_CMD_SOFTSWITCH * Soft switch setting command for BF60x
914 CONFIG_CMD_SOURCE "source" command Support
915 CONFIG_CMD_SPI * SPI serial bus support
916 CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
917 CONFIG_CMD_TFTPPUT * TFTP put command (upload)
918 CONFIG_CMD_TIME * run command and report execution time (ARM specific)
919 CONFIG_CMD_TIMER * access to the system tick timer
920 CONFIG_CMD_USB * USB support
921 CONFIG_CMD_CDP * Cisco Discover Protocol support
922 CONFIG_CMD_MFSL * Microblaze FSL support
923 CONFIG_CMD_XIMG Load part of Multi Image
926 EXAMPLE: If you want all functions except of network
927 support you can write:
929 #include "config_cmd_all.h"
930 #undef CONFIG_CMD_NET
933 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
935 Note: Don't enable the "icache" and "dcache" commands
936 (configuration option CONFIG_CMD_CACHE) unless you know
937 what you (and your U-Boot users) are doing. Data
938 cache cannot be enabled on systems like the 8xx or
939 8260 (where accesses to the IMMR region must be
940 uncached), and it cannot be disabled on all other
941 systems where we (mis-) use the data cache to hold an
942 initial stack and some data.
945 XXX - this list needs to get updated!
947 - Regular expression support:
949 If this variable is defined, U-Boot is linked against
950 the SLRE (Super Light Regular Expression) library,
951 which adds regex support to some commands, as for
952 example "env grep" and "setexpr".
956 If this variable is defined, U-Boot will use a device tree
957 to configure its devices, instead of relying on statically
958 compiled #defines in the board file. This option is
959 experimental and only available on a few boards. The device
960 tree is available in the global data as gd->fdt_blob.
962 U-Boot needs to get its device tree from somewhere. This can
963 be done using one of the two options below:
966 If this variable is defined, U-Boot will embed a device tree
967 binary in its image. This device tree file should be in the
968 board directory and called <soc>-<board>.dts. The binary file
969 is then picked up in board_init_f() and made available through
970 the global data structure as gd->blob.
973 If this variable is defined, U-Boot will build a device tree
974 binary. It will be called u-boot.dtb. Architecture-specific
975 code will locate it at run-time. Generally this works by:
977 cat u-boot.bin u-boot.dtb >image.bin
979 and in fact, U-Boot does this for you, creating a file called
980 u-boot-dtb.bin which is useful in the common case. You can
981 still use the individual files if you need something more
986 If this variable is defined, it enables watchdog
987 support for the SoC. There must be support in the SoC
988 specific code for a watchdog. For the 8xx and 8260
989 CPUs, the SIU Watchdog feature is enabled in the SYPCR
990 register. When supported for a specific SoC is
991 available, then no further board specific code should
995 When using a watchdog circuitry external to the used
996 SoC, then define this variable and provide board
997 specific code for the "hw_watchdog_reset" function.
1000 CONFIG_VERSION_VARIABLE
1001 If this variable is defined, an environment variable
1002 named "ver" is created by U-Boot showing the U-Boot
1003 version as printed by the "version" command.
1004 Any change to this variable will be reverted at the
1009 When CONFIG_CMD_DATE is selected, the type of the RTC
1010 has to be selected, too. Define exactly one of the
1013 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
1014 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
1015 CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
1016 CONFIG_RTC_MC146818 - use MC146818 RTC
1017 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
1018 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
1019 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
1020 CONFIG_RTC_DS164x - use Dallas DS164x RTC
1021 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
1022 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
1023 CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
1024 CONFIG_SYS_RV3029_TCR - enable trickle charger on
1027 Note that if the RTC uses I2C, then the I2C interface
1028 must also be configured. See I2C Support, below.
1031 CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
1032 CONFIG_PCA953X_INFO - enable pca953x info command
1034 The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
1035 chip-ngpio pairs that tell the PCA953X driver the number of
1036 pins supported by a particular chip.
1038 Note that if the GPIO device uses I2C, then the I2C interface
1039 must also be configured. See I2C Support, below.
1041 - Timestamp Support:
1043 When CONFIG_TIMESTAMP is selected, the timestamp
1044 (date and time) of an image is printed by image
1045 commands like bootm or iminfo. This option is
1046 automatically enabled when you select CONFIG_CMD_DATE .
1048 - Partition Labels (disklabels) Supported:
1049 Zero or more of the following:
1050 CONFIG_MAC_PARTITION Apple's MacOS partition table.
1051 CONFIG_DOS_PARTITION MS Dos partition table, traditional on the
1052 Intel architecture, USB sticks, etc.
1053 CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc.
1054 CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
1055 bootloader. Note 2TB partition limit; see
1057 CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
1059 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
1060 CONFIG_CMD_SCSI) you must configure support for at
1061 least one non-MTD partition type as well.
1064 CONFIG_IDE_RESET_ROUTINE - this is defined in several
1065 board configurations files but used nowhere!
1067 CONFIG_IDE_RESET - is this is defined, IDE Reset will
1068 be performed by calling the function
1069 ide_set_reset(int reset)
1070 which has to be defined in a board specific file
1075 Set this to enable ATAPI support.
1080 Set this to enable support for disks larger than 137GB
1081 Also look at CONFIG_SYS_64BIT_LBA.
1082 Whithout these , LBA48 support uses 32bit variables and will 'only'
1083 support disks up to 2.1TB.
1085 CONFIG_SYS_64BIT_LBA:
1086 When enabled, makes the IDE subsystem use 64bit sector addresses.
1090 At the moment only there is only support for the
1091 SYM53C8XX SCSI controller; define
1092 CONFIG_SCSI_SYM53C8XX to enable it.
1094 CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
1095 CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
1096 CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
1097 maximum numbers of LUNs, SCSI ID's and target
1099 CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
1101 The environment variable 'scsidevs' is set to the number of
1102 SCSI devices found during the last scan.
1104 - NETWORK Support (PCI):
1106 Support for Intel 8254x/8257x gigabit chips.
1109 Utility code for direct access to the SPI bus on Intel 8257x.
1110 This does not do anything useful unless you set at least one
1111 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
1113 CONFIG_E1000_SPI_GENERIC
1114 Allow generic access to the SPI bus on the Intel 8257x, for
1115 example with the "sspi" command.
1118 Management command for E1000 devices. When used on devices
1119 with SPI support you can reprogram the EEPROM from U-Boot.
1121 CONFIG_E1000_FALLBACK_MAC
1122 default MAC for empty EEPROM after production.
1125 Support for Intel 82557/82559/82559ER chips.
1126 Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
1127 write routine for first time initialisation.
1130 Support for Digital 2114x chips.
1131 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
1132 modem chip initialisation (KS8761/QS6611).
1135 Support for National dp83815 chips.
1138 Support for National dp8382[01] gigabit chips.
1140 - NETWORK Support (other):
1142 CONFIG_DRIVER_AT91EMAC
1143 Support for AT91RM9200 EMAC.
1146 Define this to use reduced MII inteface
1148 CONFIG_DRIVER_AT91EMAC_QUIET
1149 If this defined, the driver is quiet.
1150 The driver doen't show link status messages.
1152 CONFIG_CALXEDA_XGMAC
1153 Support for the Calxeda XGMAC device
1156 Support for SMSC's LAN91C96 chips.
1158 CONFIG_LAN91C96_BASE
1159 Define this to hold the physical address
1160 of the LAN91C96's I/O space
1162 CONFIG_LAN91C96_USE_32_BIT
1163 Define this to enable 32 bit addressing
1166 Support for SMSC's LAN91C111 chip
1168 CONFIG_SMC91111_BASE
1169 Define this to hold the physical address
1170 of the device (I/O space)
1172 CONFIG_SMC_USE_32_BIT
1173 Define this if data bus is 32 bits
1175 CONFIG_SMC_USE_IOFUNCS
1176 Define this to use i/o functions instead of macros
1177 (some hardware wont work with macros)
1179 CONFIG_DRIVER_TI_EMAC
1180 Support for davinci emac
1182 CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
1183 Define this if you have more then 3 PHYs.
1186 Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
1188 CONFIG_FTGMAC100_EGIGA
1189 Define this to use GE link update with gigabit PHY.
1190 Define this if FTGMAC100 is connected to gigabit PHY.
1191 If your system has 10/100 PHY only, it might not occur
1192 wrong behavior. Because PHY usually return timeout or
1193 useless data when polling gigabit status and gigabit
1194 control registers. This behavior won't affect the
1195 correctnessof 10/100 link speed update.
1198 Support for SMSC's LAN911x and LAN921x chips
1201 Define this to hold the physical address
1202 of the device (I/O space)
1204 CONFIG_SMC911X_32_BIT
1205 Define this if data bus is 32 bits
1207 CONFIG_SMC911X_16_BIT
1208 Define this if data bus is 16 bits. If your processor
1209 automatically converts one 32 bit word to two 16 bit
1210 words you may also try CONFIG_SMC911X_32_BIT.
1213 Support for Renesas on-chip Ethernet controller
1215 CONFIG_SH_ETHER_USE_PORT
1216 Define the number of ports to be used
1218 CONFIG_SH_ETHER_PHY_ADDR
1219 Define the ETH PHY's address
1221 CONFIG_SH_ETHER_CACHE_WRITEBACK
1222 If this option is set, the driver enables cache flush.
1226 Support TPM devices.
1229 Support for i2c bus TPM devices. Only one device
1230 per system is supported at this time.
1232 CONFIG_TPM_TIS_I2C_BUS_NUMBER
1233 Define the the i2c bus number for the TPM device
1235 CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS
1236 Define the TPM's address on the i2c bus
1238 CONFIG_TPM_TIS_I2C_BURST_LIMITATION
1239 Define the burst count bytes upper limit
1241 CONFIG_TPM_ATMEL_TWI
1242 Support for Atmel TWI TPM device. Requires I2C support.
1245 Support for generic parallel port TPM devices. Only one device
1246 per system is supported at this time.
1248 CONFIG_TPM_TIS_BASE_ADDRESS
1249 Base address where the generic TPM device is mapped
1250 to. Contemporary x86 systems usually map it at
1254 Add tpm monitor functions.
1255 Requires CONFIG_TPM. If CONFIG_TPM_AUTH_SESSIONS is set, also
1256 provides monitor access to authorized functions.
1259 Define this to enable the TPM support library which provides
1260 functional interfaces to some TPM commands.
1261 Requires support for a TPM device.
1263 CONFIG_TPM_AUTH_SESSIONS
1264 Define this to enable authorized functions in the TPM library.
1265 Requires CONFIG_TPM and CONFIG_SHA1.
1268 At the moment only the UHCI host controller is
1269 supported (PIP405, MIP405, MPC5200); define
1270 CONFIG_USB_UHCI to enable it.
1271 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
1272 and define CONFIG_USB_STORAGE to enable the USB
1275 Supported are USB Keyboards and USB Floppy drives
1277 MPC5200 USB requires additional defines:
1279 for 528 MHz Clock: 0x0001bbbb
1283 for differential drivers: 0x00001000
1284 for single ended drivers: 0x00005000
1285 for differential drivers on PSC3: 0x00000100
1286 for single ended drivers on PSC3: 0x00004100
1287 CONFIG_SYS_USB_EVENT_POLL
1288 May be defined to allow interrupt polling
1289 instead of using asynchronous interrupts
1291 CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
1292 txfilltuning field in the EHCI controller on reset.
1294 CONFIG_USB_HUB_MIN_POWER_ON_DELAY defines the minimum
1295 interval for usb hub power-on delay.(minimum 100msec)
1298 Define the below if you wish to use the USB console.
1299 Once firmware is rebuilt from a serial console issue the
1300 command "setenv stdin usbtty; setenv stdout usbtty" and
1301 attach your USB cable. The Unix command "dmesg" should print
1302 it has found a new device. The environment variable usbtty
1303 can be set to gserial or cdc_acm to enable your device to
1304 appear to a USB host as a Linux gserial device or a
1305 Common Device Class Abstract Control Model serial device.
1306 If you select usbtty = gserial you should be able to enumerate
1308 # modprobe usbserial vendor=0xVendorID product=0xProductID
1309 else if using cdc_acm, simply setting the environment
1310 variable usbtty to be cdc_acm should suffice. The following
1311 might be defined in YourBoardName.h
1314 Define this to build a UDC device
1317 Define this to have a tty type of device available to
1318 talk to the UDC device
1321 Define this to enable the high speed support for usb
1322 device and usbtty. If this feature is enabled, a routine
1323 int is_usbd_high_speed(void)
1324 also needs to be defined by the driver to dynamically poll
1325 whether the enumeration has succeded at high speed or full
1328 CONFIG_SYS_CONSOLE_IS_IN_ENV
1329 Define this if you want stdin, stdout &/or stderr to
1333 CONFIG_SYS_USB_EXTC_CLK 0xBLAH
1334 Derive USB clock from external clock "blah"
1335 - CONFIG_SYS_USB_EXTC_CLK 0x02
1337 CONFIG_SYS_USB_BRG_CLK 0xBLAH
1338 Derive USB clock from brgclk
1339 - CONFIG_SYS_USB_BRG_CLK 0x04
1341 If you have a USB-IF assigned VendorID then you may wish to
1342 define your own vendor specific values either in BoardName.h
1343 or directly in usbd_vendor_info.h. If you don't define
1344 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
1345 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
1346 should pretend to be a Linux device to it's target host.
1348 CONFIG_USBD_MANUFACTURER
1349 Define this string as the name of your company for
1350 - CONFIG_USBD_MANUFACTURER "my company"
1352 CONFIG_USBD_PRODUCT_NAME
1353 Define this string as the name of your product
1354 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
1356 CONFIG_USBD_VENDORID
1357 Define this as your assigned Vendor ID from the USB
1358 Implementors Forum. This *must* be a genuine Vendor ID
1359 to avoid polluting the USB namespace.
1360 - CONFIG_USBD_VENDORID 0xFFFF
1362 CONFIG_USBD_PRODUCTID
1363 Define this as the unique Product ID
1365 - CONFIG_USBD_PRODUCTID 0xFFFF
1367 - ULPI Layer Support:
1368 The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
1369 the generic ULPI layer. The generic layer accesses the ULPI PHY
1370 via the platform viewport, so you need both the genric layer and
1371 the viewport enabled. Currently only Chipidea/ARC based
1372 viewport is supported.
1373 To enable the ULPI layer support, define CONFIG_USB_ULPI and
1374 CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
1375 If your ULPI phy needs a different reference clock than the
1376 standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
1377 the appropriate value in Hz.
1380 The MMC controller on the Intel PXA is supported. To
1381 enable this define CONFIG_MMC. The MMC can be
1382 accessed from the boot prompt by mapping the device
1383 to physical memory similar to flash. Command line is
1384 enabled with CONFIG_CMD_MMC. The MMC driver also works with
1385 the FAT fs. This is enabled with CONFIG_CMD_FAT.
1388 Support for Renesas on-chip MMCIF controller
1390 CONFIG_SH_MMCIF_ADDR
1391 Define the base address of MMCIF registers
1394 Define the clock frequency for MMCIF
1396 - USB Device Firmware Update (DFU) class support:
1398 This enables the USB portion of the DFU USB class
1401 This enables the command "dfu" which is used to have
1402 U-Boot create a DFU class device via USB. This command
1403 requires that the "dfu_alt_info" environment variable be
1404 set and define the alt settings to expose to the host.
1407 This enables support for exposing (e)MMC devices via DFU.
1410 This enables support for exposing NAND devices via DFU.
1412 CONFIG_SYS_DFU_DATA_BUF_SIZE
1413 Dfu transfer uses a buffer before writing data to the
1414 raw storage device. Make the size (in bytes) of this buffer
1415 configurable. The size of this buffer is also configurable
1416 through the "dfu_bufsiz" environment variable.
1418 CONFIG_SYS_DFU_MAX_FILE_SIZE
1419 When updating files rather than the raw storage device,
1420 we use a static buffer to copy the file into and then write
1421 the buffer once we've been given the whole file. Define
1422 this to the maximum filesize (in bytes) for the buffer.
1423 Default is 4 MiB if undefined.
1425 - Journaling Flash filesystem support:
1426 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
1427 CONFIG_JFFS2_NAND_DEV
1428 Define these for a default partition on a NAND device
1430 CONFIG_SYS_JFFS2_FIRST_SECTOR,
1431 CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
1432 Define these for a default partition on a NOR device
1434 CONFIG_SYS_JFFS_CUSTOM_PART
1435 Define this to create an own partition. You have to provide a
1436 function struct part_info* jffs2_part_info(int part_num)
1438 If you define only one JFFS2 partition you may also want to
1439 #define CONFIG_SYS_JFFS_SINGLE_PART 1
1440 to disable the command chpart. This is the default when you
1441 have not defined a custom partition
1443 - FAT(File Allocation Table) filesystem write function support:
1446 Define this to enable support for saving memory data as a
1447 file in FAT formatted partition.
1449 This will also enable the command "fatwrite" enabling the
1450 user to write files to FAT.
1452 CBFS (Coreboot Filesystem) support
1455 Define this to enable support for reading from a Coreboot
1456 filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
1462 Define this to enable standard (PC-Style) keyboard
1466 Standard PC keyboard driver with US (is default) and
1467 GERMAN key layout (switch via environment 'keymap=de') support.
1468 Export function i8042_kbd_init, i8042_tstc and i8042_getc
1469 for cfb_console. Supports cursor blinking.
1472 Enables a Chrome OS keyboard using the CROS_EC interface.
1473 This uses CROS_EC to communicate with a second microcontroller
1474 which provides key scans on request.
1479 Define this to enable video support (for output to
1482 CONFIG_VIDEO_CT69000
1484 Enable Chips & Technologies 69000 Video chip
1486 CONFIG_VIDEO_SMI_LYNXEM
1487 Enable Silicon Motion SMI 712/710/810 Video chip. The
1488 video output is selected via environment 'videoout'
1489 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
1492 For the CT69000 and SMI_LYNXEM drivers, videomode is
1493 selected via environment 'videomode'. Two different ways
1495 - "videomode=num" 'num' is a standard LiLo mode numbers.
1496 Following standard modes are supported (* is default):
1498 Colors 640x480 800x600 1024x768 1152x864 1280x1024
1499 -------------+---------------------------------------------
1500 8 bits | 0x301* 0x303 0x305 0x161 0x307
1501 15 bits | 0x310 0x313 0x316 0x162 0x319
1502 16 bits | 0x311 0x314 0x317 0x163 0x31A
1503 24 bits | 0x312 0x315 0x318 ? 0x31B
1504 -------------+---------------------------------------------
1505 (i.e. setenv videomode 317; saveenv; reset;)
1507 - "videomode=bootargs" all the video parameters are parsed
1508 from the bootargs. (See drivers/video/videomodes.c)
1511 CONFIG_VIDEO_SED13806
1512 Enable Epson SED13806 driver. This driver supports 8bpp
1513 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
1514 or CONFIG_VIDEO_SED13806_16BPP
1517 Enable the Freescale DIU video driver. Reference boards for
1518 SOCs that have a DIU should define this macro to enable DIU
1519 support, and should also define these other macros:
1525 CONFIG_VIDEO_SW_CURSOR
1526 CONFIG_VGA_AS_SINGLE_DEVICE
1528 CONFIG_VIDEO_BMP_LOGO
1530 The DIU driver will look for the 'video-mode' environment
1531 variable, and if defined, enable the DIU as a console during
1532 boot. See the documentation file README.video for a
1533 description of this variable.
1537 Enable the VGA video / BIOS for x86. The alternative if you
1538 are using coreboot is to use the coreboot frame buffer
1545 Define this to enable a custom keyboard support.
1546 This simply calls drv_keyboard_init() which must be
1547 defined in your board-specific files.
1548 The only board using this so far is RBC823.
1550 - LCD Support: CONFIG_LCD
1552 Define this to enable LCD support (for output to LCD
1553 display); also select one of the supported displays
1554 by defining one of these:
1558 HITACHI TX09D70VM1CCA, 3.5", 240x320.
1560 CONFIG_NEC_NL6448AC33:
1562 NEC NL6448AC33-18. Active, color, single scan.
1564 CONFIG_NEC_NL6448BC20
1566 NEC NL6448BC20-08. 6.5", 640x480.
1567 Active, color, single scan.
1569 CONFIG_NEC_NL6448BC33_54
1571 NEC NL6448BC33-54. 10.4", 640x480.
1572 Active, color, single scan.
1576 Sharp 320x240. Active, color, single scan.
1577 It isn't 16x9, and I am not sure what it is.
1579 CONFIG_SHARP_LQ64D341
1581 Sharp LQ64D341 display, 640x480.
1582 Active, color, single scan.
1586 HLD1045 display, 640x480.
1587 Active, color, single scan.
1591 Optrex CBL50840-2 NF-FW 99 22 M5
1593 Hitachi LMG6912RPFC-00T
1597 320x240. Black & white.
1599 Normally display is black on white background; define
1600 CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
1602 CONFIG_LCD_ALIGNMENT
1604 Normally the LCD is page-aligned (tyically 4KB). If this is
1605 defined then the LCD will be aligned to this value instead.
1606 For ARM it is sometimes useful to use MMU_SECTION_SIZE
1607 here, since it is cheaper to change data cache settings on
1608 a per-section basis.
1610 CONFIG_CONSOLE_SCROLL_LINES
1612 When the console need to be scrolled, this is the number of
1613 lines to scroll by. It defaults to 1. Increasing this makes
1614 the console jump but can help speed up operation when scrolling
1619 Support drawing of RLE8-compressed bitmaps on the LCD.
1623 Enables an 'i2c edid' command which can read EDID
1624 information over I2C from an attached LCD display.
1626 - Splash Screen Support: CONFIG_SPLASH_SCREEN
1628 If this option is set, the environment is checked for
1629 a variable "splashimage". If found, the usual display
1630 of logo, copyright and system information on the LCD
1631 is suppressed and the BMP image at the address
1632 specified in "splashimage" is loaded instead. The
1633 console is redirected to the "nulldev", too. This
1634 allows for a "silent" boot where a splash screen is
1635 loaded very quickly after power-on.
1637 CONFIG_SPLASHIMAGE_GUARD
1639 If this option is set, then U-Boot will prevent the environment
1640 variable "splashimage" from being set to a problematic address
1641 (see README.displaying-bmps and README.arm-unaligned-accesses).
1642 This option is useful for targets where, due to alignment
1643 restrictions, an improperly aligned BMP image will cause a data
1644 abort. If you think you will not have problems with unaligned
1645 accesses (for example because your toolchain prevents them)
1646 there is no need to set this option.
1648 CONFIG_SPLASH_SCREEN_ALIGN
1650 If this option is set the splash image can be freely positioned
1651 on the screen. Environment variable "splashpos" specifies the
1652 position as "x,y". If a positive number is given it is used as
1653 number of pixel from left/top. If a negative number is given it
1654 is used as number of pixel from right/bottom. You can also
1655 specify 'm' for centering the image.
1658 setenv splashpos m,m
1659 => image at center of screen
1661 setenv splashpos 30,20
1662 => image at x = 30 and y = 20
1664 setenv splashpos -10,m
1665 => vertically centered image
1666 at x = dspWidth - bmpWidth - 9
1668 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
1670 If this option is set, additionally to standard BMP
1671 images, gzipped BMP images can be displayed via the
1672 splashscreen support or the bmp command.
1674 - Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
1676 If this option is set, 8-bit RLE compressed BMP images
1677 can be displayed via the splashscreen support or the
1680 - Do compresssing for memory range:
1683 If this option is set, it would use zlib deflate method
1684 to compress the specified memory at its best effort.
1686 - Compression support:
1689 If this option is set, support for bzip2 compressed
1690 images is included. If not, only uncompressed and gzip
1691 compressed images are supported.
1693 NOTE: the bzip2 algorithm requires a lot of RAM, so
1694 the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
1699 If this option is set, support for lzma compressed
1702 Note: The LZMA algorithm adds between 2 and 4KB of code and it
1703 requires an amount of dynamic memory that is given by the
1706 (1846 + 768 << (lc + lp)) * sizeof(uint16)
1708 Where lc and lp stand for, respectively, Literal context bits
1709 and Literal pos bits.
1711 This value is upper-bounded by 14MB in the worst case. Anyway,
1712 for a ~4MB large kernel image, we have lc=3 and lp=0 for a
1713 total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
1714 a very small buffer.
1716 Use the lzmainfo tool to determinate the lc and lp values and
1717 then calculate the amount of needed dynamic memory (ensuring
1718 the appropriate CONFIG_SYS_MALLOC_LEN value).
1723 The address of PHY on MII bus.
1725 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
1727 The clock frequency of the MII bus
1731 If this option is set, support for speed/duplex
1732 detection of gigabit PHY is included.
1734 CONFIG_PHY_RESET_DELAY
1736 Some PHY like Intel LXT971A need extra delay after
1737 reset before any MII register access is possible.
1738 For such PHY, set this option to the usec delay
1739 required. (minimum 300usec for LXT971A)
1741 CONFIG_PHY_CMD_DELAY (ppc4xx)
1743 Some PHY like Intel LXT971A need extra delay after
1744 command issued before MII status register can be read
1754 Define a default value for Ethernet address to use
1755 for the respective Ethernet interface, in case this
1756 is not determined automatically.
1761 Define a default value for the IP address to use for
1762 the default Ethernet interface, in case this is not
1763 determined through e.g. bootp.
1764 (Environment variable "ipaddr")
1766 - Server IP address:
1769 Defines a default value for the IP address of a TFTP
1770 server to contact when using the "tftboot" command.
1771 (Environment variable "serverip")
1773 CONFIG_KEEP_SERVERADDR
1775 Keeps the server's MAC address, in the env 'serveraddr'
1776 for passing to bootargs (like Linux's netconsole option)
1778 - Gateway IP address:
1781 Defines a default value for the IP address of the
1782 default router where packets to other networks are
1784 (Environment variable "gatewayip")
1789 Defines a default value for the subnet mask (or
1790 routing prefix) which is used to determine if an IP
1791 address belongs to the local subnet or needs to be
1792 forwarded through a router.
1793 (Environment variable "netmask")
1795 - Multicast TFTP Mode:
1798 Defines whether you want to support multicast TFTP as per
1799 rfc-2090; for example to work with atftp. Lets lots of targets
1800 tftp down the same boot image concurrently. Note: the Ethernet
1801 driver in use must provide a function: mcast() to join/leave a
1804 - BOOTP Recovery Mode:
1805 CONFIG_BOOTP_RANDOM_DELAY
1807 If you have many targets in a network that try to
1808 boot using BOOTP, you may want to avoid that all
1809 systems send out BOOTP requests at precisely the same
1810 moment (which would happen for instance at recovery
1811 from a power failure, when all systems will try to
1812 boot, thus flooding the BOOTP server. Defining
1813 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1814 inserted before sending out BOOTP requests. The
1815 following delays are inserted then:
1817 1st BOOTP request: delay 0 ... 1 sec
1818 2nd BOOTP request: delay 0 ... 2 sec
1819 3rd BOOTP request: delay 0 ... 4 sec
1821 BOOTP requests: delay 0 ... 8 sec
1823 - DHCP Advanced Options:
1824 You can fine tune the DHCP functionality by defining
1825 CONFIG_BOOTP_* symbols:
1827 CONFIG_BOOTP_SUBNETMASK
1828 CONFIG_BOOTP_GATEWAY
1829 CONFIG_BOOTP_HOSTNAME
1830 CONFIG_BOOTP_NISDOMAIN
1831 CONFIG_BOOTP_BOOTPATH
1832 CONFIG_BOOTP_BOOTFILESIZE
1835 CONFIG_BOOTP_SEND_HOSTNAME
1836 CONFIG_BOOTP_NTPSERVER
1837 CONFIG_BOOTP_TIMEOFFSET
1838 CONFIG_BOOTP_VENDOREX
1839 CONFIG_BOOTP_MAY_FAIL
1841 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
1842 environment variable, not the BOOTP server.
1844 CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found
1845 after the configured retry count, the call will fail
1846 instead of starting over. This can be used to fail over
1847 to Link-local IP address configuration if the DHCP server
1850 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1851 serverip from a DHCP server, it is possible that more
1852 than one DNS serverip is offered to the client.
1853 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1854 serverip will be stored in the additional environment
1855 variable "dnsip2". The first DNS serverip is always
1856 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1859 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1860 to do a dynamic update of a DNS server. To do this, they
1861 need the hostname of the DHCP requester.
1862 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
1863 of the "hostname" environment variable is passed as
1864 option 12 to the DHCP server.
1866 CONFIG_BOOTP_DHCP_REQUEST_DELAY
1868 A 32bit value in microseconds for a delay between
1869 receiving a "DHCP Offer" and sending the "DHCP Request".
1870 This fixes a problem with certain DHCP servers that don't
1871 respond 100% of the time to a "DHCP request". E.g. On an
1872 AT91RM9200 processor running at 180MHz, this delay needed
1873 to be *at least* 15,000 usec before a Windows Server 2003
1874 DHCP server would reply 100% of the time. I recommend at
1875 least 50,000 usec to be safe. The alternative is to hope
1876 that one of the retries will be successful but note that
1877 the DHCP timeout and retry process takes a longer than
1880 - Link-local IP address negotiation:
1881 Negotiate with other link-local clients on the local network
1882 for an address that doesn't require explicit configuration.
1883 This is especially useful if a DHCP server cannot be guaranteed
1884 to exist in all environments that the device must operate.
1886 See doc/README.link-local for more information.
1889 CONFIG_CDP_DEVICE_ID
1891 The device id used in CDP trigger frames.
1893 CONFIG_CDP_DEVICE_ID_PREFIX
1895 A two character string which is prefixed to the MAC address
1900 A printf format string which contains the ascii name of
1901 the port. Normally is set to "eth%d" which sets
1902 eth0 for the first Ethernet, eth1 for the second etc.
1904 CONFIG_CDP_CAPABILITIES
1906 A 32bit integer which indicates the device capabilities;
1907 0x00000010 for a normal host which does not forwards.
1911 An ascii string containing the version of the software.
1915 An ascii string containing the name of the platform.
1919 A 32bit integer sent on the trigger.
1921 CONFIG_CDP_POWER_CONSUMPTION
1923 A 16bit integer containing the power consumption of the
1924 device in .1 of milliwatts.
1926 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1928 A byte containing the id of the VLAN.
1930 - Status LED: CONFIG_STATUS_LED
1932 Several configurations allow to display the current
1933 status using a LED. For instance, the LED will blink
1934 fast while running U-Boot code, stop blinking as
1935 soon as a reply to a BOOTP request was received, and
1936 start blinking slow once the Linux kernel is running
1937 (supported by a status LED driver in the Linux
1938 kernel). Defining CONFIG_STATUS_LED enables this
1941 - CAN Support: CONFIG_CAN_DRIVER
1943 Defining CONFIG_CAN_DRIVER enables CAN driver support
1944 on those systems that support this (optional)
1945 feature, like the TQM8xxL modules.
1947 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1949 These enable I2C serial bus commands. Defining either of
1950 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1951 include the appropriate I2C driver for the selected CPU.
1953 This will allow you to use i2c commands at the u-boot
1954 command line (as long as you set CONFIG_CMD_I2C in
1955 CONFIG_COMMANDS) and communicate with i2c based realtime
1956 clock chips. See common/cmd_i2c.c for a description of the
1957 command line interface.
1959 CONFIG_HARD_I2C selects a hardware I2C controller.
1961 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1962 bit-banging) driver instead of CPM or similar hardware
1965 There are several other quantities that must also be
1966 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1968 In both cases you will need to define CONFIG_SYS_I2C_SPEED
1969 to be the frequency (in Hz) at which you wish your i2c bus
1970 to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
1971 the CPU's i2c node address).
1973 Now, the u-boot i2c code for the mpc8xx
1974 (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
1975 and so its address should therefore be cleared to 0 (See,
1976 eg, MPC823e User's Manual p.16-473). So, set
1977 CONFIG_SYS_I2C_SLAVE to 0.
1979 CONFIG_SYS_I2C_INIT_MPC5XXX
1981 When a board is reset during an i2c bus transfer
1982 chips might think that the current transfer is still
1983 in progress. Reset the slave devices by sending start
1984 commands until the slave device responds.
1986 That's all that's required for CONFIG_HARD_I2C.
1988 If you use the software i2c interface (CONFIG_SOFT_I2C)
1989 then the following macros need to be defined (examples are
1990 from include/configs/lwmon.h):
1994 (Optional). Any commands necessary to enable the I2C
1995 controller or configure ports.
1997 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
2001 (Only for MPC8260 CPU). The I/O port to use (the code
2002 assumes both bits are on the same port). Valid values
2003 are 0..3 for ports A..D.
2007 The code necessary to make the I2C data line active
2008 (driven). If the data line is open collector, this
2011 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
2015 The code necessary to make the I2C data line tri-stated
2016 (inactive). If the data line is open collector, this
2019 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
2023 Code that returns true if the I2C data line is high,
2026 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
2030 If <bit> is true, sets the I2C data line high. If it
2031 is false, it clears it (low).
2033 eg: #define I2C_SDA(bit) \
2034 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
2035 else immr->im_cpm.cp_pbdat &= ~PB_SDA
2039 If <bit> is true, sets the I2C clock line high. If it
2040 is false, it clears it (low).
2042 eg: #define I2C_SCL(bit) \
2043 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
2044 else immr->im_cpm.cp_pbdat &= ~PB_SCL
2048 This delay is invoked four times per clock cycle so this
2049 controls the rate of data transfer. The data rate thus
2050 is 1 / (I2C_DELAY * 4). Often defined to be something
2053 #define I2C_DELAY udelay(2)
2055 CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
2057 If your arch supports the generic GPIO framework (asm/gpio.h),
2058 then you may alternatively define the two GPIOs that are to be
2059 used as SCL / SDA. Any of the previous I2C_xxx macros will
2060 have GPIO-based defaults assigned to them as appropriate.
2062 You should define these to the GPIO value as given directly to
2063 the generic GPIO functions.
2065 CONFIG_SYS_I2C_INIT_BOARD
2067 When a board is reset during an i2c bus transfer
2068 chips might think that the current transfer is still
2069 in progress. On some boards it is possible to access
2070 the i2c SCLK line directly, either by using the
2071 processor pin as a GPIO or by having a second pin
2072 connected to the bus. If this option is defined a
2073 custom i2c_init_board() routine in boards/xxx/board.c
2074 is run early in the boot sequence.
2076 CONFIG_SYS_I2C_BOARD_LATE_INIT
2078 An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
2079 defined a custom i2c_board_late_init() routine in
2080 boards/xxx/board.c is run AFTER the operations in i2c_init()
2081 is completed. This callpoint can be used to unreset i2c bus
2082 using CPU i2c controller register accesses for CPUs whose i2c
2083 controller provide such a method. It is called at the end of
2084 i2c_init() to allow i2c_init operations to setup the i2c bus
2085 controller on the CPU (e.g. setting bus speed & slave address).
2087 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
2089 This option enables configuration of bi_iic_fast[] flags
2090 in u-boot bd_info structure based on u-boot environment
2091 variable "i2cfast". (see also i2cfast)
2093 CONFIG_I2C_MULTI_BUS
2095 This option allows the use of multiple I2C buses, each of which
2096 must have a controller. At any point in time, only one bus is
2097 active. To switch to a different bus, use the 'i2c dev' command.
2098 Note that bus numbering is zero-based.
2100 CONFIG_SYS_I2C_NOPROBES
2102 This option specifies a list of I2C devices that will be skipped
2103 when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
2104 is set, specify a list of bus-device pairs. Otherwise, specify
2105 a 1D array of device addresses
2108 #undef CONFIG_I2C_MULTI_BUS
2109 #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
2111 will skip addresses 0x50 and 0x68 on a board with one I2C bus
2113 #define CONFIG_I2C_MULTI_BUS
2114 #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
2116 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
2118 CONFIG_SYS_SPD_BUS_NUM
2120 If defined, then this indicates the I2C bus number for DDR SPD.
2121 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
2123 CONFIG_SYS_RTC_BUS_NUM
2125 If defined, then this indicates the I2C bus number for the RTC.
2126 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
2128 CONFIG_SYS_DTT_BUS_NUM
2130 If defined, then this indicates the I2C bus number for the DTT.
2131 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
2133 CONFIG_SYS_I2C_DTT_ADDR:
2135 If defined, specifies the I2C address of the DTT device.
2136 If not defined, then U-Boot uses predefined value for
2137 specified DTT device.
2141 Define this option if you want to use Freescale's I2C driver in
2142 drivers/i2c/fsl_i2c.c.
2146 Define this option if you have I2C devices reached over 1 .. n
2147 I2C Muxes like the pca9544a. This option addes a new I2C
2148 Command "i2c bus [muxtype:muxaddr:muxchannel]" which adds a
2149 new I2C Bus to the existing I2C Busses. If you select the
2150 new Bus with "i2c dev", u-bbot sends first the commandos for
2151 the muxes to activate this new "bus".
2153 CONFIG_I2C_MULTI_BUS must be also defined, to use this
2157 Adding a new I2C Bus reached over 2 pca9544a muxes
2158 The First mux with address 70 and channel 6
2159 The Second mux with address 71 and channel 4
2161 => i2c bus pca9544a:70:6:pca9544a:71:4
2163 Use the "i2c bus" command without parameter, to get a list
2164 of I2C Busses with muxes:
2167 Busses reached over muxes:
2169 reached over Mux(es):
2172 reached over Mux(es):
2177 If you now switch to the new I2C Bus 3 with "i2c dev 3"
2178 u-boot first sends the command to the mux@70 to enable
2179 channel 6, and then the command to the mux@71 to enable
2182 After that, you can use the "normal" i2c commands as
2183 usual to communicate with your I2C devices behind
2186 This option is actually implemented for the bitbanging
2187 algorithm in common/soft_i2c.c and for the Hardware I2C
2188 Bus on the MPC8260. But it should be not so difficult
2189 to add this option to other architectures.
2191 CONFIG_SOFT_I2C_READ_REPEATED_START
2193 defining this will force the i2c_read() function in
2194 the soft_i2c driver to perform an I2C repeated start
2195 between writing the address pointer and reading the
2196 data. If this define is omitted the default behaviour
2197 of doing a stop-start sequence will be used. Most I2C
2198 devices can use either method, but some require one or
2201 - SPI Support: CONFIG_SPI
2203 Enables SPI driver (so far only tested with
2204 SPI EEPROM, also an instance works with Crystal A/D and
2205 D/As on the SACSng board)
2209 Enables the driver for SPI controller on SuperH. Currently
2210 only SH7757 is supported.
2214 Enables extended (16-bit) SPI EEPROM addressing.
2215 (symmetrical to CONFIG_I2C_X)
2219 Enables a software (bit-bang) SPI driver rather than
2220 using hardware support. This is a general purpose
2221 driver that only requires three general I/O port pins
2222 (two outputs, one input) to function. If this is
2223 defined, the board configuration must define several
2224 SPI configuration items (port pins to use, etc). For
2225 an example, see include/configs/sacsng.h.
2229 Enables a hardware SPI driver for general-purpose reads
2230 and writes. As with CONFIG_SOFT_SPI, the board configuration
2231 must define a list of chip-select function pointers.
2232 Currently supported on some MPC8xxx processors. For an
2233 example, see include/configs/mpc8349emds.h.
2237 Enables the driver for the SPI controllers on i.MX and MXC
2238 SoCs. Currently i.MX31/35/51 are supported.
2240 - FPGA Support: CONFIG_FPGA
2242 Enables FPGA subsystem.
2244 CONFIG_FPGA_<vendor>
2246 Enables support for specific chip vendors.
2249 CONFIG_FPGA_<family>
2251 Enables support for FPGA family.
2252 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
2256 Specify the number of FPGA devices to support.
2258 CONFIG_SYS_FPGA_PROG_FEEDBACK
2260 Enable printing of hash marks during FPGA configuration.
2262 CONFIG_SYS_FPGA_CHECK_BUSY
2264 Enable checks on FPGA configuration interface busy
2265 status by the configuration function. This option
2266 will require a board or device specific function to
2271 If defined, a function that provides delays in the FPGA
2272 configuration driver.
2274 CONFIG_SYS_FPGA_CHECK_CTRLC
2275 Allow Control-C to interrupt FPGA configuration
2277 CONFIG_SYS_FPGA_CHECK_ERROR
2279 Check for configuration errors during FPGA bitfile
2280 loading. For example, abort during Virtex II
2281 configuration if the INIT_B line goes low (which
2282 indicated a CRC error).
2284 CONFIG_SYS_FPGA_WAIT_INIT
2286 Maximum time to wait for the INIT_B line to deassert
2287 after PROB_B has been deasserted during a Virtex II
2288 FPGA configuration sequence. The default time is 500
2291 CONFIG_SYS_FPGA_WAIT_BUSY
2293 Maximum time to wait for BUSY to deassert during
2294 Virtex II FPGA configuration. The default is 5 ms.
2296 CONFIG_SYS_FPGA_WAIT_CONFIG
2298 Time to wait after FPGA configuration. The default is
2301 - Configuration Management:
2304 If defined, this string will be added to the U-Boot
2305 version information (U_BOOT_VERSION)
2307 - Vendor Parameter Protection:
2309 U-Boot considers the values of the environment
2310 variables "serial#" (Board Serial Number) and
2311 "ethaddr" (Ethernet Address) to be parameters that
2312 are set once by the board vendor / manufacturer, and
2313 protects these variables from casual modification by
2314 the user. Once set, these variables are read-only,
2315 and write or delete attempts are rejected. You can
2316 change this behaviour:
2318 If CONFIG_ENV_OVERWRITE is #defined in your config
2319 file, the write protection for vendor parameters is
2320 completely disabled. Anybody can change or delete
2323 Alternatively, if you #define _both_ CONFIG_ETHADDR
2324 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
2325 Ethernet address is installed in the environment,
2326 which can be changed exactly ONCE by the user. [The
2327 serial# is unaffected by this, i. e. it remains
2330 The same can be accomplished in a more flexible way
2331 for any variable by configuring the type of access
2332 to allow for those variables in the ".flags" variable
2333 or define CONFIG_ENV_FLAGS_LIST_STATIC.
2338 Define this variable to enable the reservation of
2339 "protected RAM", i. e. RAM which is not overwritten
2340 by U-Boot. Define CONFIG_PRAM to hold the number of
2341 kB you want to reserve for pRAM. You can overwrite
2342 this default value by defining an environment
2343 variable "pram" to the number of kB you want to
2344 reserve. Note that the board info structure will
2345 still show the full amount of RAM. If pRAM is
2346 reserved, a new environment variable "mem" will
2347 automatically be defined to hold the amount of
2348 remaining RAM in a form that can be passed as boot
2349 argument to Linux, for instance like that:
2351 setenv bootargs ... mem=\${mem}
2354 This way you can tell Linux not to use this memory,
2355 either, which results in a memory region that will
2356 not be affected by reboots.
2358 *WARNING* If your board configuration uses automatic
2359 detection of the RAM size, you must make sure that
2360 this memory test is non-destructive. So far, the
2361 following board configurations are known to be
2364 IVMS8, IVML24, SPD8xx, TQM8xxL,
2365 HERMES, IP860, RPXlite, LWMON,
2368 - Access to physical memory region (> 4GB)
2369 Some basic support is provided for operations on memory not
2370 normally accessible to U-Boot - e.g. some architectures
2371 support access to more than 4GB of memory on 32-bit
2372 machines using physical address extension or similar.
2373 Define CONFIG_PHYSMEM to access this basic support, which
2374 currently only supports clearing the memory.
2379 Define this variable to stop the system in case of a
2380 fatal error, so that you have to reset it manually.
2381 This is probably NOT a good idea for an embedded
2382 system where you want the system to reboot
2383 automatically as fast as possible, but it may be
2384 useful during development since you can try to debug
2385 the conditions that lead to the situation.
2387 CONFIG_NET_RETRY_COUNT
2389 This variable defines the number of retries for
2390 network operations like ARP, RARP, TFTP, or BOOTP
2391 before giving up the operation. If not defined, a
2392 default value of 5 is used.
2396 Timeout waiting for an ARP reply in milliseconds.
2400 Timeout in milliseconds used in NFS protocol.
2401 If you encounter "ERROR: Cannot umount" in nfs command,
2402 try longer timeout such as
2403 #define CONFIG_NFS_TIMEOUT 10000UL
2405 - Command Interpreter:
2406 CONFIG_AUTO_COMPLETE
2408 Enable auto completion of commands using TAB.
2410 Note that this feature has NOT been implemented yet
2411 for the "hush" shell.
2414 CONFIG_SYS_HUSH_PARSER
2416 Define this variable to enable the "hush" shell (from
2417 Busybox) as command line interpreter, thus enabling
2418 powerful command line syntax like
2419 if...then...else...fi conditionals or `&&' and '||'
2420 constructs ("shell scripts").
2422 If undefined, you get the old, much simpler behaviour
2423 with a somewhat smaller memory footprint.
2426 CONFIG_SYS_PROMPT_HUSH_PS2
2428 This defines the secondary prompt string, which is
2429 printed when the command interpreter needs more input
2430 to complete a command. Usually "> ".
2434 In the current implementation, the local variables
2435 space and global environment variables space are
2436 separated. Local variables are those you define by
2437 simply typing `name=value'. To access a local
2438 variable later on, you have write `$name' or
2439 `${name}'; to execute the contents of a variable
2440 directly type `$name' at the command prompt.
2442 Global environment variables are those you use
2443 setenv/printenv to work with. To run a command stored
2444 in such a variable, you need to use the run command,
2445 and you must not use the '$' sign to access them.
2447 To store commands and special characters in a
2448 variable, please use double quotation marks
2449 surrounding the whole text of the variable, instead
2450 of the backslashes before semicolons and special
2453 - Commandline Editing and History:
2454 CONFIG_CMDLINE_EDITING
2456 Enable editing and History functions for interactive
2457 commandline input operations
2459 - Default Environment:
2460 CONFIG_EXTRA_ENV_SETTINGS
2462 Define this to contain any number of null terminated
2463 strings (variable = value pairs) that will be part of
2464 the default environment compiled into the boot image.
2466 For example, place something like this in your
2467 board's config file:
2469 #define CONFIG_EXTRA_ENV_SETTINGS \
2473 Warning: This method is based on knowledge about the
2474 internal format how the environment is stored by the
2475 U-Boot code. This is NOT an official, exported
2476 interface! Although it is unlikely that this format
2477 will change soon, there is no guarantee either.
2478 You better know what you are doing here.
2480 Note: overly (ab)use of the default environment is
2481 discouraged. Make sure to check other ways to preset
2482 the environment like the "source" command or the
2485 CONFIG_ENV_VARS_UBOOT_CONFIG
2487 Define this in order to add variables describing the
2488 U-Boot build configuration to the default environment.
2489 These will be named arch, cpu, board, vendor, and soc.
2491 Enabling this option will cause the following to be defined:
2499 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
2501 Define this in order to add variables describing certain
2502 run-time determined information about the hardware to the
2503 environment. These will be named board_name, board_rev.
2505 CONFIG_DELAY_ENVIRONMENT
2507 Normally the environment is loaded when the board is
2508 intialised so that it is available to U-Boot. This inhibits
2509 that so that the environment is not available until
2510 explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL
2511 this is instead controlled by the value of
2512 /config/load-environment.
2514 - DataFlash Support:
2515 CONFIG_HAS_DATAFLASH
2517 Defining this option enables DataFlash features and
2518 allows to read/write in Dataflash via the standard
2521 - Serial Flash support
2524 Defining this option enables SPI flash commands
2525 'sf probe/read/write/erase/update'.
2527 Usage requires an initial 'probe' to define the serial
2528 flash parameters, followed by read/write/erase/update
2531 The following defaults may be provided by the platform
2532 to handle the common case when only a single serial
2533 flash is present on the system.
2535 CONFIG_SF_DEFAULT_BUS Bus identifier
2536 CONFIG_SF_DEFAULT_CS Chip-select
2537 CONFIG_SF_DEFAULT_MODE (see include/spi.h)
2538 CONFIG_SF_DEFAULT_SPEED in Hz
2542 Define this option to include a destructive SPI flash
2545 CONFIG_SPI_FLASH_BAR Ban/Extended Addr Reg
2547 Define this option to use the Bank addr/Extended addr
2548 support on SPI flashes which has size > 16Mbytes.
2550 - SystemACE Support:
2553 Adding this option adds support for Xilinx SystemACE
2554 chips attached via some sort of local bus. The address
2555 of the chip must also be defined in the
2556 CONFIG_SYS_SYSTEMACE_BASE macro. For example:
2558 #define CONFIG_SYSTEMACE
2559 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
2561 When SystemACE support is added, the "ace" device type
2562 becomes available to the fat commands, i.e. fatls.
2564 - TFTP Fixed UDP Port:
2567 If this is defined, the environment variable tftpsrcp
2568 is used to supply the TFTP UDP source port value.
2569 If tftpsrcp isn't defined, the normal pseudo-random port
2570 number generator is used.
2572 Also, the environment variable tftpdstp is used to supply
2573 the TFTP UDP destination port value. If tftpdstp isn't
2574 defined, the normal port 69 is used.
2576 The purpose for tftpsrcp is to allow a TFTP server to
2577 blindly start the TFTP transfer using the pre-configured
2578 target IP address and UDP port. This has the effect of
2579 "punching through" the (Windows XP) firewall, allowing
2580 the remainder of the TFTP transfer to proceed normally.
2581 A better solution is to properly configure the firewall,
2582 but sometimes that is not allowed.
2587 This enables a generic 'hash' command which can produce
2588 hashes / digests from a few algorithms (e.g. SHA1, SHA256).
2592 Enable the hash verify command (hash -v). This adds to code
2595 CONFIG_SHA1 - support SHA1 hashing
2596 CONFIG_SHA256 - support SHA256 hashing
2598 Note: There is also a sha1sum command, which should perhaps
2599 be deprecated in favour of 'hash sha1'.
2604 This enables the RSA algorithm used for FIT image verification
2605 in U-Boot. See doc/uImage/signature for more information.
2607 The signing part is build into mkimage regardless of this
2611 - Show boot progress:
2612 CONFIG_SHOW_BOOT_PROGRESS
2614 Defining this option allows to add some board-
2615 specific code (calling a user-provided function
2616 "show_boot_progress(int)") that enables you to show
2617 the system's boot progress on some display (for
2618 example, some LED's) on your board. At the moment,
2619 the following checkpoints are implemented:
2621 - Detailed boot stage timing
2623 Define this option to get detailed timing of each stage
2624 of the boot process.
2626 CONFIG_BOOTSTAGE_USER_COUNT
2627 This is the number of available user bootstage records.
2628 Each time you call bootstage_mark(BOOTSTAGE_ID_ALLOC, ...)
2629 a new ID will be allocated from this stash. If you exceed
2630 the limit, recording will stop.
2632 CONFIG_BOOTSTAGE_REPORT
2633 Define this to print a report before boot, similar to this:
2635 Timer summary in microseconds:
2638 3,575,678 3,575,678 board_init_f start
2639 3,575,695 17 arch_cpu_init A9
2640 3,575,777 82 arch_cpu_init done
2641 3,659,598 83,821 board_init_r start
2642 3,910,375 250,777 main_loop
2643 29,916,167 26,005,792 bootm_start
2644 30,361,327 445,160 start_kernel
2646 CONFIG_CMD_BOOTSTAGE
2647 Add a 'bootstage' command which supports printing a report
2648 and un/stashing of bootstage data.
2650 CONFIG_BOOTSTAGE_FDT
2651 Stash the bootstage information in the FDT. A root 'bootstage'
2652 node is created with each bootstage id as a child. Each child
2653 has a 'name' property and either 'mark' containing the
2654 mark time in microsecond, or 'accum' containing the
2655 accumulated time for that bootstage id in microseconds.
2660 name = "board_init_f";
2669 Code in the Linux kernel can find this in /proc/devicetree.
2671 Legacy uImage format:
2674 1 common/cmd_bootm.c before attempting to boot an image
2675 -1 common/cmd_bootm.c Image header has bad magic number
2676 2 common/cmd_bootm.c Image header has correct magic number
2677 -2 common/cmd_bootm.c Image header has bad checksum
2678 3 common/cmd_bootm.c Image header has correct checksum
2679 -3 common/cmd_bootm.c Image data has bad checksum
2680 4 common/cmd_bootm.c Image data has correct checksum
2681 -4 common/cmd_bootm.c Image is for unsupported architecture
2682 5 common/cmd_bootm.c Architecture check OK
2683 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
2684 6 common/cmd_bootm.c Image Type check OK
2685 -6 common/cmd_bootm.c gunzip uncompression error
2686 -7 common/cmd_bootm.c Unimplemented compression type
2687 7 common/cmd_bootm.c Uncompression OK
2688 8 common/cmd_bootm.c No uncompress/copy overwrite error
2689 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
2691 9 common/image.c Start initial ramdisk verification
2692 -10 common/image.c Ramdisk header has bad magic number
2693 -11 common/image.c Ramdisk header has bad checksum
2694 10 common/image.c Ramdisk header is OK
2695 -12 common/image.c Ramdisk data has bad checksum
2696 11 common/image.c Ramdisk data has correct checksum
2697 12 common/image.c Ramdisk verification complete, start loading
2698 -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
2699 13 common/image.c Start multifile image verification
2700 14 common/image.c No initial ramdisk, no multifile, continue.
2702 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
2704 -30 arch/powerpc/lib/board.c Fatal error, hang the system
2705 -31 post/post.c POST test failed, detected by post_output_backlog()
2706 -32 post/post.c POST test failed, detected by post_run_single()
2708 34 common/cmd_doc.c before loading a Image from a DOC device
2709 -35 common/cmd_doc.c Bad usage of "doc" command
2710 35 common/cmd_doc.c correct usage of "doc" command
2711 -36 common/cmd_doc.c No boot device
2712 36 common/cmd_doc.c correct boot device
2713 -37 common/cmd_doc.c Unknown Chip ID on boot device
2714 37 common/cmd_doc.c correct chip ID found, device available
2715 -38 common/cmd_doc.c Read Error on boot device
2716 38 common/cmd_doc.c reading Image header from DOC device OK
2717 -39 common/cmd_doc.c Image header has bad magic number
2718 39 common/cmd_doc.c Image header has correct magic number
2719 -40 common/cmd_doc.c Error reading Image from DOC device
2720 40 common/cmd_doc.c Image header has correct magic number
2721 41 common/cmd_ide.c before loading a Image from a IDE device
2722 -42 common/cmd_ide.c Bad usage of "ide" command
2723 42 common/cmd_ide.c correct usage of "ide" command
2724 -43 common/cmd_ide.c No boot device
2725 43 common/cmd_ide.c boot device found
2726 -44 common/cmd_ide.c Device not available
2727 44 common/cmd_ide.c Device available
2728 -45 common/cmd_ide.c wrong partition selected
2729 45 common/cmd_ide.c partition selected
2730 -46 common/cmd_ide.c Unknown partition table
2731 46 common/cmd_ide.c valid partition table found
2732 -47 common/cmd_ide.c Invalid partition type
2733 47 common/cmd_ide.c correct partition type
2734 -48 common/cmd_ide.c Error reading Image Header on boot device
2735 48 common/cmd_ide.c reading Image Header from IDE device OK
2736 -49 common/cmd_ide.c Image header has bad magic number
2737 49 common/cmd_ide.c Image header has correct magic number
2738 -50 common/cmd_ide.c Image header has bad checksum
2739 50 common/cmd_ide.c Image header has correct checksum
2740 -51 common/cmd_ide.c Error reading Image from IDE device
2741 51 common/cmd_ide.c reading Image from IDE device OK
2742 52 common/cmd_nand.c before loading a Image from a NAND device
2743 -53 common/cmd_nand.c Bad usage of "nand" command
2744 53 common/cmd_nand.c correct usage of "nand" command
2745 -54 common/cmd_nand.c No boot device
2746 54 common/cmd_nand.c boot device found
2747 -55 common/cmd_nand.c Unknown Chip ID on boot device
2748 55 common/cmd_nand.c correct chip ID found, device available
2749 -56 common/cmd_nand.c Error reading Image Header on boot device
2750 56 common/cmd_nand.c reading Image Header from NAND device OK
2751 -57 common/cmd_nand.c Image header has bad magic number
2752 57 common/cmd_nand.c Image header has correct magic number
2753 -58 common/cmd_nand.c Error reading Image from NAND device
2754 58 common/cmd_nand.c reading Image from NAND device OK
2756 -60 common/env_common.c Environment has a bad CRC, using default
2758 64 net/eth.c starting with Ethernet configuration.
2759 -64 net/eth.c no Ethernet found.
2760 65 net/eth.c Ethernet found.
2762 -80 common/cmd_net.c usage wrong
2763 80 common/cmd_net.c before calling NetLoop()
2764 -81 common/cmd_net.c some error in NetLoop() occurred
2765 81 common/cmd_net.c NetLoop() back without error
2766 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
2767 82 common/cmd_net.c trying automatic boot
2768 83 common/cmd_net.c running "source" command
2769 -83 common/cmd_net.c some error in automatic boot or "source" command
2770 84 common/cmd_net.c end without errors
2775 100 common/cmd_bootm.c Kernel FIT Image has correct format
2776 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
2777 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
2778 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
2779 102 common/cmd_bootm.c Kernel unit name specified
2780 -103 common/cmd_bootm.c Can't get kernel subimage node offset
2781 103 common/cmd_bootm.c Found configuration node
2782 104 common/cmd_bootm.c Got kernel subimage node offset
2783 -104 common/cmd_bootm.c Kernel subimage hash verification failed
2784 105 common/cmd_bootm.c Kernel subimage hash verification OK
2785 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
2786 106 common/cmd_bootm.c Architecture check OK
2787 -106 common/cmd_bootm.c Kernel subimage has wrong type
2788 107 common/cmd_bootm.c Kernel subimage type OK
2789 -107 common/cmd_bootm.c Can't get kernel subimage data/size
2790 108 common/cmd_bootm.c Got kernel subimage data/size
2791 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
2792 -109 common/cmd_bootm.c Can't get kernel subimage type
2793 -110 common/cmd_bootm.c Can't get kernel subimage comp
2794 -111 common/cmd_bootm.c Can't get kernel subimage os
2795 -112 common/cmd_bootm.c Can't get kernel subimage load address
2796 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
2798 120 common/image.c Start initial ramdisk verification
2799 -120 common/image.c Ramdisk FIT image has incorrect format
2800 121 common/image.c Ramdisk FIT image has correct format
2801 122 common/image.c No ramdisk subimage unit name, using configuration
2802 -122 common/image.c Can't get configuration for ramdisk subimage
2803 123 common/image.c Ramdisk unit name specified
2804 -124 common/image.c Can't get ramdisk subimage node offset
2805 125 common/image.c Got ramdisk subimage node offset
2806 -125 common/image.c Ramdisk subimage hash verification failed
2807 126 common/image.c Ramdisk subimage hash verification OK
2808 -126 common/image.c Ramdisk subimage for unsupported architecture
2809 127 common/image.c Architecture check OK
2810 -127 common/image.c Can't get ramdisk subimage data/size
2811 128 common/image.c Got ramdisk subimage data/size
2812 129 common/image.c Can't get ramdisk load address
2813 -129 common/image.c Got ramdisk load address
2815 -130 common/cmd_doc.c Incorrect FIT image format
2816 131 common/cmd_doc.c FIT image format OK
2818 -140 common/cmd_ide.c Incorrect FIT image format
2819 141 common/cmd_ide.c FIT image format OK
2821 -150 common/cmd_nand.c Incorrect FIT image format
2822 151 common/cmd_nand.c FIT image format OK
2824 - FIT image support:
2826 Enable support for the FIT uImage format.
2828 CONFIG_FIT_BEST_MATCH
2829 When no configuration is explicitly selected, default to the
2830 one whose fdt's compatibility field best matches that of
2831 U-Boot itself. A match is considered "best" if it matches the
2832 most specific compatibility entry of U-Boot's fdt's root node.
2833 The order of entries in the configuration's fdt is ignored.
2835 CONFIG_FIT_SIGNATURE
2836 This option enables signature verification of FIT uImages,
2837 using a hash signed and verified using RSA. See
2838 doc/uImage.FIT/signature.txt for more details.
2840 - Standalone program support:
2841 CONFIG_STANDALONE_LOAD_ADDR
2843 This option defines a board specific value for the
2844 address where standalone program gets loaded, thus
2845 overwriting the architecture dependent default
2848 - Frame Buffer Address:
2851 Define CONFIG_FB_ADDR if you want to use specific
2852 address for frame buffer. This is typically the case
2853 when using a graphics controller has separate video
2854 memory. U-Boot will then place the frame buffer at
2855 the given address instead of dynamically reserving it
2856 in system RAM by calling lcd_setmem(), which grabs
2857 the memory for the frame buffer depending on the
2858 configured panel size.
2860 Please see board_init_f function.
2862 - Automatic software updates via TFTP server
2864 CONFIG_UPDATE_TFTP_CNT_MAX
2865 CONFIG_UPDATE_TFTP_MSEC_MAX
2867 These options enable and control the auto-update feature;
2868 for a more detailed description refer to doc/README.update.
2870 - MTD Support (mtdparts command, UBI support)
2873 Adds the MTD device infrastructure from the Linux kernel.
2874 Needed for mtdparts command support.
2876 CONFIG_MTD_PARTITIONS
2878 Adds the MTD partitioning infrastructure from the Linux
2879 kernel. Needed for UBI support.
2884 Adds commands for interacting with MTD partitions formatted
2885 with the UBI flash translation layer
2887 Requires also defining CONFIG_RBTREE
2889 CONFIG_UBI_SILENCE_MSG
2891 Make the verbose messages from UBI stop printing. This leaves
2892 warnings and errors enabled.
2897 Adds commands for interacting with UBI volumes formatted as
2898 UBIFS. UBIFS is read-only in u-boot.
2900 Requires UBI support as well as CONFIG_LZO
2902 CONFIG_UBIFS_SILENCE_MSG
2904 Make the verbose messages from UBIFS stop printing. This leaves
2905 warnings and errors enabled.
2909 Enable building of SPL globally.
2912 LDSCRIPT for linking the SPL binary.
2914 CONFIG_SPL_MAX_FOOTPRINT
2915 Maximum size in memory allocated to the SPL, BSS included.
2916 When defined, the linker checks that the actual memory
2917 used by SPL from _start to __bss_end does not exceed it.
2918 CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
2919 must not be both defined at the same time.
2922 Maximum size of the SPL image (text, data, rodata, and
2923 linker lists sections), BSS excluded.
2924 When defined, the linker checks that the actual size does
2927 CONFIG_SPL_TEXT_BASE
2928 TEXT_BASE for linking the SPL binary.
2930 CONFIG_SPL_RELOC_TEXT_BASE
2931 Address to relocate to. If unspecified, this is equal to
2932 CONFIG_SPL_TEXT_BASE (i.e. no relocation is done).
2934 CONFIG_SPL_BSS_START_ADDR
2935 Link address for the BSS within the SPL binary.
2937 CONFIG_SPL_BSS_MAX_SIZE
2938 Maximum size in memory allocated to the SPL BSS.
2939 When defined, the linker checks that the actual memory used
2940 by SPL from __bss_start to __bss_end does not exceed it.
2941 CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
2942 must not be both defined at the same time.
2945 Adress of the start of the stack SPL will use
2947 CONFIG_SPL_RELOC_STACK
2948 Adress of the start of the stack SPL will use after
2949 relocation. If unspecified, this is equal to
2952 CONFIG_SYS_SPL_MALLOC_START
2953 Starting address of the malloc pool used in SPL.
2955 CONFIG_SYS_SPL_MALLOC_SIZE
2956 The size of the malloc pool used in SPL.
2958 CONFIG_SPL_FRAMEWORK
2959 Enable the SPL framework under common/. This framework
2960 supports MMC, NAND and YMODEM loading of U-Boot and NAND
2961 NAND loading of the Linux Kernel.
2963 CONFIG_SPL_DISPLAY_PRINT
2964 For ARM, enable an optional function to print more information
2965 about the running system.
2967 CONFIG_SPL_INIT_MINIMAL
2968 Arch init code should be built for a very small image
2970 CONFIG_SPL_LIBCOMMON_SUPPORT
2971 Support for common/libcommon.o in SPL binary
2973 CONFIG_SPL_LIBDISK_SUPPORT
2974 Support for disk/libdisk.o in SPL binary
2976 CONFIG_SPL_I2C_SUPPORT
2977 Support for drivers/i2c/libi2c.o in SPL binary
2979 CONFIG_SPL_GPIO_SUPPORT
2980 Support for drivers/gpio/libgpio.o in SPL binary
2982 CONFIG_SPL_MMC_SUPPORT
2983 Support for drivers/mmc/libmmc.o in SPL binary
2985 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
2986 CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
2987 CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION
2988 Address, size and partition on the MMC to load U-Boot from
2989 when the MMC is being used in raw mode.
2991 CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
2992 Sector to load kernel uImage from when MMC is being
2993 used in raw mode (for Falcon mode)
2995 CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR,
2996 CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
2997 Sector and number of sectors to load kernel argument
2998 parameters from when MMC is being used in raw mode
3001 CONFIG_SPL_FAT_SUPPORT
3002 Support for fs/fat/libfat.o in SPL binary
3004 CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
3005 Filename to read to load U-Boot when reading from FAT
3007 CONFIG_SPL_FAT_LOAD_KERNEL_NAME
3008 Filename to read to load kernel uImage when reading
3009 from FAT (for Falcon mode)
3011 CONFIG_SPL_FAT_LOAD_ARGS_NAME
3012 Filename to read to load kernel argument parameters
3013 when reading from FAT (for Falcon mode)
3015 CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
3016 Set this for NAND SPL on PPC mpc83xx targets, so that
3017 start.S waits for the rest of the SPL to load before
3018 continuing (the hardware starts execution after just
3019 loading the first page rather than the full 4K).
3021 CONFIG_SPL_NAND_BASE
3022 Include nand_base.c in the SPL. Requires
3023 CONFIG_SPL_NAND_DRIVERS.
3025 CONFIG_SPL_NAND_DRIVERS
3026 SPL uses normal NAND drivers, not minimal drivers.
3029 Include standard software ECC in the SPL
3031 CONFIG_SPL_NAND_SIMPLE
3032 Support for NAND boot using simple NAND drivers that
3033 expose the cmd_ctrl() interface.
3035 CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
3036 CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
3037 CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
3038 CONFIG_SYS_NAND_ECCPOS, CONFIG_SYS_NAND_ECCSIZE,
3039 CONFIG_SYS_NAND_ECCBYTES
3040 Defines the size and behavior of the NAND that SPL uses
3043 CONFIG_SYS_NAND_U_BOOT_OFFS
3044 Location in NAND to read U-Boot from
3046 CONFIG_SYS_NAND_U_BOOT_DST
3047 Location in memory to load U-Boot to
3049 CONFIG_SYS_NAND_U_BOOT_SIZE
3050 Size of image to load
3052 CONFIG_SYS_NAND_U_BOOT_START
3053 Entry point in loaded image to jump to
3055 CONFIG_SYS_NAND_HW_ECC_OOBFIRST
3056 Define this if you need to first read the OOB and then the
3057 data. This is used for example on davinci plattforms.
3059 CONFIG_SPL_OMAP3_ID_NAND
3060 Support for an OMAP3-specific set of functions to return the
3061 ID and MFR of the first attached NAND chip, if present.
3063 CONFIG_SPL_SERIAL_SUPPORT
3064 Support for drivers/serial/libserial.o in SPL binary
3066 CONFIG_SPL_SPI_FLASH_SUPPORT
3067 Support for drivers/mtd/spi/libspi_flash.o in SPL binary
3069 CONFIG_SPL_SPI_SUPPORT
3070 Support for drivers/spi/libspi.o in SPL binary
3072 CONFIG_SPL_RAM_DEVICE
3073 Support for running image already present in ram, in SPL binary
3075 CONFIG_SPL_LIBGENERIC_SUPPORT
3076 Support for lib/libgeneric.o in SPL binary
3078 CONFIG_SPL_ENV_SUPPORT
3079 Support for the environment operating in SPL binary
3081 CONFIG_SPL_NET_SUPPORT
3082 Support for the net/libnet.o in SPL binary.
3083 It conflicts with SPL env from storage medium specified by
3084 CONFIG_ENV_IS_xxx but CONFIG_ENV_IS_NOWHERE
3087 Image offset to which the SPL should be padded before appending
3088 the SPL payload. By default, this is defined as
3089 CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
3090 CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
3091 payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
3094 Final target image containing SPL and payload. Some SPLs
3095 use an arch-specific makefile fragment instead, for
3096 example if more than one image needs to be produced.
3098 CONFIG_FIT_SPL_PRINT
3099 Printing information about a FIT image adds quite a bit of
3100 code to SPL. So this is normally disabled in SPL. Use this
3101 option to re-enable it. This will affect the output of the
3102 bootm command when booting a FIT image.
3107 [so far only for SMDK2400 boards]
3109 - Modem support enable:
3110 CONFIG_MODEM_SUPPORT
3112 - RTS/CTS Flow control enable:
3115 - Modem debug support:
3116 CONFIG_MODEM_SUPPORT_DEBUG
3118 Enables debugging stuff (char screen[1024], dbg())
3119 for modem support. Useful only with BDI2000.
3121 - Interrupt support (PPC):
3123 There are common interrupt_init() and timer_interrupt()
3124 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
3125 for CPU specific initialization. interrupt_init_cpu()
3126 should set decrementer_count to appropriate value. If
3127 CPU resets decrementer automatically after interrupt
3128 (ppc4xx) it should set decrementer_count to zero.
3129 timer_interrupt() calls timer_interrupt_cpu() for CPU
3130 specific handling. If board has watchdog / status_led
3131 / other_activity_monitor it works automatically from
3132 general timer_interrupt().
3136 In the target system modem support is enabled when a
3137 specific key (key combination) is pressed during
3138 power-on. Otherwise U-Boot will boot normally
3139 (autoboot). The key_pressed() function is called from
3140 board_init(). Currently key_pressed() is a dummy
3141 function, returning 1 and thus enabling modem
3144 If there are no modem init strings in the
3145 environment, U-Boot proceed to autoboot; the
3146 previous output (banner, info printfs) will be
3149 See also: doc/README.Modem
3151 Board initialization settings:
3152 ------------------------------
3154 During Initialization u-boot calls a number of board specific functions
3155 to allow the preparation of board specific prerequisites, e.g. pin setup
3156 before drivers are initialized. To enable these callbacks the
3157 following configuration macros have to be defined. Currently this is
3158 architecture specific, so please check arch/your_architecture/lib/board.c
3159 typically in board_init_f() and board_init_r().
3161 - CONFIG_BOARD_EARLY_INIT_F: Call board_early_init_f()
3162 - CONFIG_BOARD_EARLY_INIT_R: Call board_early_init_r()
3163 - CONFIG_BOARD_LATE_INIT: Call board_late_init()
3164 - CONFIG_BOARD_POSTCLK_INIT: Call board_postclk_init()
3166 Configuration Settings:
3167 -----------------------
3169 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
3170 undefine this when you're short of memory.
3172 - CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
3173 width of the commands listed in the 'help' command output.
3175 - CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
3176 prompt for user input.
3178 - CONFIG_SYS_CBSIZE: Buffer size for input from the Console
3180 - CONFIG_SYS_PBSIZE: Buffer size for Console output
3182 - CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
3184 - CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to
3185 the application (usually a Linux kernel) when it is
3188 - CONFIG_SYS_BAUDRATE_TABLE:
3189 List of legal baudrate settings for this board.
3191 - CONFIG_SYS_CONSOLE_INFO_QUIET
3192 Suppress display of console information at boot.
3194 - CONFIG_SYS_CONSOLE_IS_IN_ENV
3195 If the board specific function
3196 extern int overwrite_console (void);
3197 returns 1, the stdin, stderr and stdout are switched to the
3198 serial port, else the settings in the environment are used.
3200 - CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
3201 Enable the call to overwrite_console().
3203 - CONFIG_SYS_CONSOLE_ENV_OVERWRITE
3204 Enable overwrite of previous console environment settings.
3206 - CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
3207 Begin and End addresses of the area used by the
3210 - CONFIG_SYS_ALT_MEMTEST:
3211 Enable an alternate, more extensive memory test.
3213 - CONFIG_SYS_MEMTEST_SCRATCH:
3214 Scratch address used by the alternate memory test
3215 You only need to set this if address zero isn't writeable
3217 - CONFIG_SYS_MEM_TOP_HIDE (PPC only):
3218 If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
3219 this specified memory area will get subtracted from the top
3220 (end) of RAM and won't get "touched" at all by U-Boot. By
3221 fixing up gd->ram_size the Linux kernel should gets passed
3222 the now "corrected" memory size and won't touch it either.
3223 This should work for arch/ppc and arch/powerpc. Only Linux
3224 board ports in arch/powerpc with bootwrapper support that
3225 recalculate the memory size from the SDRAM controller setup
3226 will have to get fixed in Linux additionally.
3228 This option can be used as a workaround for the 440EPx/GRx
3229 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
3232 WARNING: Please make sure that this value is a multiple of
3233 the Linux page size (normally 4k). If this is not the case,
3234 then the end address of the Linux memory will be located at a
3235 non page size aligned address and this could cause major
3238 - CONFIG_SYS_LOADS_BAUD_CHANGE:
3239 Enable temporary baudrate change while serial download
3241 - CONFIG_SYS_SDRAM_BASE:
3242 Physical start address of SDRAM. _Must_ be 0 here.
3244 - CONFIG_SYS_MBIO_BASE:
3245 Physical start address of Motherboard I/O (if using a
3248 - CONFIG_SYS_FLASH_BASE:
3249 Physical start address of Flash memory.
3251 - CONFIG_SYS_MONITOR_BASE:
3252 Physical start address of boot monitor code (set by
3253 make config files to be same as the text base address
3254 (CONFIG_SYS_TEXT_BASE) used when linking) - same as
3255 CONFIG_SYS_FLASH_BASE when booting from flash.
3257 - CONFIG_SYS_MONITOR_LEN:
3258 Size of memory reserved for monitor code, used to
3259 determine _at_compile_time_ (!) if the environment is
3260 embedded within the U-Boot image, or in a separate
3263 - CONFIG_SYS_MALLOC_LEN:
3264 Size of DRAM reserved for malloc() use.
3266 - CONFIG_SYS_BOOTM_LEN:
3267 Normally compressed uImages are limited to an
3268 uncompressed size of 8 MBytes. If this is not enough,
3269 you can define CONFIG_SYS_BOOTM_LEN in your board config file
3270 to adjust this setting to your needs.
3272 - CONFIG_SYS_BOOTMAPSZ:
3273 Maximum size of memory mapped by the startup code of
3274 the Linux kernel; all data that must be processed by
3275 the Linux kernel (bd_info, boot arguments, FDT blob if
3276 used) must be put below this limit, unless "bootm_low"
3277 enviroment variable is defined and non-zero. In such case
3278 all data for the Linux kernel must be between "bootm_low"
3279 and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
3280 variable "bootm_mapsize" will override the value of
3281 CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
3282 then the value in "bootm_size" will be used instead.
3284 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
3285 Enable initrd_high functionality. If defined then the
3286 initrd_high feature is enabled and the bootm ramdisk subcommand
3289 - CONFIG_SYS_BOOT_GET_CMDLINE:
3290 Enables allocating and saving kernel cmdline in space between
3291 "bootm_low" and "bootm_low" + BOOTMAPSZ.
3293 - CONFIG_SYS_BOOT_GET_KBD:
3294 Enables allocating and saving a kernel copy of the bd_info in
3295 space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
3297 - CONFIG_SYS_MAX_FLASH_BANKS:
3298 Max number of Flash memory banks
3300 - CONFIG_SYS_MAX_FLASH_SECT:
3301 Max number of sectors on a Flash chip
3303 - CONFIG_SYS_FLASH_ERASE_TOUT:
3304 Timeout for Flash erase operations (in ms)
3306 - CONFIG_SYS_FLASH_WRITE_TOUT:
3307 Timeout for Flash write operations (in ms)
3309 - CONFIG_SYS_FLASH_LOCK_TOUT
3310 Timeout for Flash set sector lock bit operation (in ms)
3312 - CONFIG_SYS_FLASH_UNLOCK_TOUT
3313 Timeout for Flash clear lock bits operation (in ms)
3315 - CONFIG_SYS_FLASH_PROTECTION
3316 If defined, hardware flash sectors protection is used
3317 instead of U-Boot software protection.
3319 - CONFIG_SYS_DIRECT_FLASH_TFTP:
3321 Enable TFTP transfers directly to flash memory;
3322 without this option such a download has to be
3323 performed in two steps: (1) download to RAM, and (2)
3324 copy from RAM to flash.
3326 The two-step approach is usually more reliable, since
3327 you can check if the download worked before you erase
3328 the flash, but in some situations (when system RAM is
3329 too limited to allow for a temporary copy of the
3330 downloaded image) this option may be very useful.
3332 - CONFIG_SYS_FLASH_CFI:
3333 Define if the flash driver uses extra elements in the
3334 common flash structure for storing flash geometry.
3336 - CONFIG_FLASH_CFI_DRIVER
3337 This option also enables the building of the cfi_flash driver
3338 in the drivers directory
3340 - CONFIG_FLASH_CFI_MTD
3341 This option enables the building of the cfi_mtd driver
3342 in the drivers directory. The driver exports CFI flash
3345 - CONFIG_SYS_FLASH_USE_BUFFER_WRITE
3346 Use buffered writes to flash.
3348 - CONFIG_FLASH_SPANSION_S29WS_N
3349 s29ws-n MirrorBit flash has non-standard addresses for buffered
3352 - CONFIG_SYS_FLASH_QUIET_TEST
3353 If this option is defined, the common CFI flash doesn't
3354 print it's warning upon not recognized FLASH banks. This
3355 is useful, if some of the configured banks are only
3356 optionally available.
3358 - CONFIG_FLASH_SHOW_PROGRESS
3359 If defined (must be an integer), print out countdown
3360 digits and dots. Recommended value: 45 (9..1) for 80
3361 column displays, 15 (3..1) for 40 column displays.
3363 - CONFIG_FLASH_VERIFY
3364 If defined, the content of the flash (destination) is compared
3365 against the source after the write operation. An error message
3366 will be printed when the contents are not identical.
3367 Please note that this option is useless in nearly all cases,
3368 since such flash programming errors usually are detected earlier
3369 while unprotecting/erasing/programming. Please only enable
3370 this option if you really know what you are doing.
3372 - CONFIG_SYS_RX_ETH_BUFFER:
3373 Defines the number of Ethernet receive buffers. On some
3374 Ethernet controllers it is recommended to set this value
3375 to 8 or even higher (EEPRO100 or 405 EMAC), since all
3376 buffers can be full shortly after enabling the interface
3377 on high Ethernet traffic.
3378 Defaults to 4 if not defined.
3380 - CONFIG_ENV_MAX_ENTRIES
3382 Maximum number of entries in the hash table that is used
3383 internally to store the environment settings. The default
3384 setting is supposed to be generous and should work in most
3385 cases. This setting can be used to tune behaviour; see
3386 lib/hashtable.c for details.
3388 - CONFIG_ENV_FLAGS_LIST_DEFAULT
3389 - CONFIG_ENV_FLAGS_LIST_STATIC
3390 Enable validation of the values given to enviroment variables when
3391 calling env set. Variables can be restricted to only decimal,
3392 hexadecimal, or boolean. If CONFIG_CMD_NET is also defined,
3393 the variables can also be restricted to IP address or MAC address.
3395 The format of the list is:
3396 type_attribute = [s|d|x|b|i|m]
3397 access_atribute = [a|r|o|c]
3398 attributes = type_attribute[access_atribute]
3399 entry = variable_name[:attributes]
3402 The type attributes are:
3403 s - String (default)
3406 b - Boolean ([1yYtT|0nNfF])
3410 The access attributes are:
3416 - CONFIG_ENV_FLAGS_LIST_DEFAULT
3417 Define this to a list (string) to define the ".flags"
3418 envirnoment variable in the default or embedded environment.
3420 - CONFIG_ENV_FLAGS_LIST_STATIC
3421 Define this to a list (string) to define validation that
3422 should be done if an entry is not found in the ".flags"
3423 environment variable. To override a setting in the static
3424 list, simply add an entry for the same variable name to the
3427 - CONFIG_ENV_ACCESS_IGNORE_FORCE
3428 If defined, don't allow the -f switch to env set override variable
3431 - CONFIG_SYS_GENERIC_BOARD
3432 This selects the architecture-generic board system instead of the
3433 architecture-specific board files. It is intended to move boards
3434 to this new framework over time. Defining this will disable the
3435 arch/foo/lib/board.c file and use common/board_f.c and
3436 common/board_r.c instead. To use this option your architecture
3437 must support it (i.e. must define __HAVE_ARCH_GENERIC_BOARD in
3438 its config.mk file). If you find problems enabling this option on
3439 your board please report the problem and send patches!
3441 - CONFIG_SYS_SYM_OFFSETS
3442 This is set by architectures that use offsets for link symbols
3443 instead of absolute values. So bss_start is obtained using an
3444 offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
3445 directly. You should not need to touch this setting.
3447 - CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
3448 This is set by OMAP boards for the max time that reset should
3449 be asserted. See doc/README.omap-reset-time for details on how
3450 the value can be calulated on a given board.
3452 The following definitions that deal with the placement and management
3453 of environment data (variable area); in general, we support the
3454 following configurations:
3456 - CONFIG_BUILD_ENVCRC:
3458 Builds up envcrc with the target environment so that external utils
3459 may easily extract it and embed it in final U-Boot images.
3461 - CONFIG_ENV_IS_IN_FLASH:
3463 Define this if the environment is in flash memory.
3465 a) The environment occupies one whole flash sector, which is
3466 "embedded" in the text segment with the U-Boot code. This
3467 happens usually with "bottom boot sector" or "top boot
3468 sector" type flash chips, which have several smaller
3469 sectors at the start or the end. For instance, such a
3470 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
3471 such a case you would place the environment in one of the
3472 4 kB sectors - with U-Boot code before and after it. With
3473 "top boot sector" type flash chips, you would put the
3474 environment in one of the last sectors, leaving a gap
3475 between U-Boot and the environment.
3477 - CONFIG_ENV_OFFSET:
3479 Offset of environment data (variable area) to the
3480 beginning of flash memory; for instance, with bottom boot
3481 type flash chips the second sector can be used: the offset
3482 for this sector is given here.
3484 CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
3488 This is just another way to specify the start address of
3489 the flash sector containing the environment (instead of
3492 - CONFIG_ENV_SECT_SIZE:
3494 Size of the sector containing the environment.
3497 b) Sometimes flash chips have few, equal sized, BIG sectors.
3498 In such a case you don't want to spend a whole sector for
3503 If you use this in combination with CONFIG_ENV_IS_IN_FLASH
3504 and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
3505 of this flash sector for the environment. This saves
3506 memory for the RAM copy of the environment.
3508 It may also save flash memory if you decide to use this
3509 when your environment is "embedded" within U-Boot code,
3510 since then the remainder of the flash sector could be used
3511 for U-Boot code. It should be pointed out that this is
3512 STRONGLY DISCOURAGED from a robustness point of view:
3513 updating the environment in flash makes it always
3514 necessary to erase the WHOLE sector. If something goes
3515 wrong before the contents has been restored from a copy in
3516 RAM, your target system will be dead.
3518 - CONFIG_ENV_ADDR_REDUND
3519 CONFIG_ENV_SIZE_REDUND
3521 These settings describe a second storage area used to hold
3522 a redundant copy of the environment data, so that there is
3523 a valid backup copy in case there is a power failure during
3524 a "saveenv" operation.
3526 BE CAREFUL! Any changes to the flash layout, and some changes to the
3527 source code will make it necessary to adapt <board>/u-boot.lds*
3531 - CONFIG_ENV_IS_IN_NVRAM:
3533 Define this if you have some non-volatile memory device
3534 (NVRAM, battery buffered SRAM) which you want to use for the
3540 These two #defines are used to determine the memory area you
3541 want to use for environment. It is assumed that this memory
3542 can just be read and written to, without any special
3545 BE CAREFUL! The first access to the environment happens quite early
3546 in U-Boot initalization (when we try to get the setting of for the
3547 console baudrate). You *MUST* have mapped your NVRAM area then, or
3550 Please note that even with NVRAM we still use a copy of the
3551 environment in RAM: we could work on NVRAM directly, but we want to
3552 keep settings there always unmodified except somebody uses "saveenv"
3553 to save the current settings.
3556 - CONFIG_ENV_IS_IN_EEPROM:
3558 Use this if you have an EEPROM or similar serial access
3559 device and a driver for it.
3561 - CONFIG_ENV_OFFSET:
3564 These two #defines specify the offset and size of the
3565 environment area within the total memory of your EEPROM.
3567 - CONFIG_SYS_I2C_EEPROM_ADDR:
3568 If defined, specified the chip address of the EEPROM device.
3569 The default address is zero.
3571 - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
3572 If defined, the number of bits used to address bytes in a
3573 single page in the EEPROM device. A 64 byte page, for example
3574 would require six bits.
3576 - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
3577 If defined, the number of milliseconds to delay between
3578 page writes. The default is zero milliseconds.
3580 - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
3581 The length in bytes of the EEPROM memory array address. Note
3582 that this is NOT the chip address length!
3584 - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
3585 EEPROM chips that implement "address overflow" are ones
3586 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
3587 address and the extra bits end up in the "chip address" bit
3588 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
3591 Note that we consider the length of the address field to
3592 still be one byte because the extra address bits are hidden
3593 in the chip address.
3595 - CONFIG_SYS_EEPROM_SIZE:
3596 The size in bytes of the EEPROM device.
3598 - CONFIG_ENV_EEPROM_IS_ON_I2C
3599 define this, if you have I2C and SPI activated, and your
3600 EEPROM, which holds the environment, is on the I2C bus.
3602 - CONFIG_I2C_ENV_EEPROM_BUS
3603 if you have an Environment on an EEPROM reached over
3604 I2C muxes, you can define here, how to reach this
3605 EEPROM. For example:
3607 #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0"
3609 EEPROM which holds the environment, is reached over
3610 a pca9547 i2c mux with address 0x70, channel 3.
3612 - CONFIG_ENV_IS_IN_DATAFLASH:
3614 Define this if you have a DataFlash memory device which you
3615 want to use for the environment.
3617 - CONFIG_ENV_OFFSET:
3621 These three #defines specify the offset and size of the
3622 environment area within the total memory of your DataFlash placed
3623 at the specified address.
3625 - CONFIG_ENV_IS_IN_REMOTE:
3627 Define this if you have a remote memory space which you
3628 want to use for the local device's environment.
3633 These two #defines specify the address and size of the
3634 environment area within the remote memory space. The
3635 local device can get the environment from remote memory
3636 space by SRIO or PCIE links.
3638 BE CAREFUL! For some special cases, the local device can not use
3639 "saveenv" command. For example, the local device will get the
3640 environment stored in a remote NOR flash by SRIO or PCIE link,
3641 but it can not erase, write this NOR flash by SRIO or PCIE interface.
3643 - CONFIG_ENV_IS_IN_NAND:
3645 Define this if you have a NAND device which you want to use
3646 for the environment.
3648 - CONFIG_ENV_OFFSET:
3651 These two #defines specify the offset and size of the environment
3652 area within the first NAND device. CONFIG_ENV_OFFSET must be
3653 aligned to an erase block boundary.
3655 - CONFIG_ENV_OFFSET_REDUND (optional):
3657 This setting describes a second storage area of CONFIG_ENV_SIZE
3658 size used to hold a redundant copy of the environment data, so
3659 that there is a valid backup copy in case there is a power failure
3660 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
3661 aligned to an erase block boundary.
3663 - CONFIG_ENV_RANGE (optional):
3665 Specifies the length of the region in which the environment
3666 can be written. This should be a multiple of the NAND device's
3667 block size. Specifying a range with more erase blocks than
3668 are needed to hold CONFIG_ENV_SIZE allows bad blocks within
3669 the range to be avoided.
3671 - CONFIG_ENV_OFFSET_OOB (optional):
3673 Enables support for dynamically retrieving the offset of the
3674 environment from block zero's out-of-band data. The
3675 "nand env.oob" command can be used to record this offset.
3676 Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
3677 using CONFIG_ENV_OFFSET_OOB.
3679 - CONFIG_NAND_ENV_DST
3681 Defines address in RAM to which the nand_spl code should copy the
3682 environment. If redundant environment is used, it will be copied to
3683 CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
3685 - CONFIG_ENV_IS_IN_UBI:
3687 Define this if you have an UBI volume that you want to use for the
3688 environment. This has the benefit of wear-leveling the environment
3689 accesses, which is important on NAND.
3691 - CONFIG_ENV_UBI_PART:
3693 Define this to a string that is the mtd partition containing the UBI.
3695 - CONFIG_ENV_UBI_VOLUME:
3697 Define this to the name of the volume that you want to store the
3700 - CONFIG_ENV_UBI_VOLUME_REDUND:
3702 Define this to the name of another volume to store a second copy of
3703 the environment in. This will enable redundant environments in UBI.
3704 It is assumed that both volumes are in the same MTD partition.
3706 - CONFIG_UBI_SILENCE_MSG
3707 - CONFIG_UBIFS_SILENCE_MSG
3709 You will probably want to define these to avoid a really noisy system
3710 when storing the env in UBI.
3712 - CONFIG_ENV_IS_IN_MMC:
3714 Define this if you have an MMC device which you want to use for the
3717 - CONFIG_SYS_MMC_ENV_DEV:
3719 Specifies which MMC device the environment is stored in.
3721 - CONFIG_SYS_MMC_ENV_PART (optional):
3723 Specifies which MMC partition the environment is stored in. If not
3724 set, defaults to partition 0, the user area. Common values might be
3725 1 (first MMC boot partition), 2 (second MMC boot partition).
3727 - CONFIG_ENV_OFFSET:
3730 These two #defines specify the offset and size of the environment
3731 area within the specified MMC device.
3733 If offset is positive (the usual case), it is treated as relative to
3734 the start of the MMC partition. If offset is negative, it is treated
3735 as relative to the end of the MMC partition. This can be useful if
3736 your board may be fitted with different MMC devices, which have
3737 different sizes for the MMC partitions, and you always want the
3738 environment placed at the very end of the partition, to leave the
3739 maximum possible space before it, to store other data.
3741 These two values are in units of bytes, but must be aligned to an
3742 MMC sector boundary.
3744 - CONFIG_ENV_OFFSET_REDUND (optional):
3746 Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
3747 hold a redundant copy of the environment data. This provides a
3748 valid backup copy in case the other copy is corrupted, e.g. due
3749 to a power failure during a "saveenv" operation.
3751 This value may also be positive or negative; this is handled in the
3752 same way as CONFIG_ENV_OFFSET.
3754 This value is also in units of bytes, but must also be aligned to
3755 an MMC sector boundary.
3757 - CONFIG_ENV_SIZE_REDUND (optional):
3759 This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
3760 set. If this value is set, it must be set to the same value as
3763 - CONFIG_SYS_SPI_INIT_OFFSET
3765 Defines offset to the initial SPI buffer area in DPRAM. The
3766 area is used at an early stage (ROM part) if the environment
3767 is configured to reside in the SPI EEPROM: We need a 520 byte
3768 scratch DPRAM area. It is used between the two initialization
3769 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
3770 to be a good choice since it makes it far enough from the
3771 start of the data area as well as from the stack pointer.
3773 Please note that the environment is read-only until the monitor
3774 has been relocated to RAM and a RAM copy of the environment has been
3775 created; also, when using EEPROM you will have to use getenv_f()
3776 until then to read environment variables.
3778 The environment is protected by a CRC32 checksum. Before the monitor
3779 is relocated into RAM, as a result of a bad CRC you will be working
3780 with the compiled-in default environment - *silently*!!! [This is
3781 necessary, because the first environment variable we need is the
3782 "baudrate" setting for the console - if we have a bad CRC, we don't
3783 have any device yet where we could complain.]
3785 Note: once the monitor has been relocated, then it will complain if
3786 the default environment is used; a new CRC is computed as soon as you
3787 use the "saveenv" command to store a valid environment.
3789 - CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
3790 Echo the inverted Ethernet link state to the fault LED.
3792 Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
3793 also needs to be defined.
3795 - CONFIG_SYS_FAULT_MII_ADDR:
3796 MII address of the PHY to check for the Ethernet link state.
3798 - CONFIG_NS16550_MIN_FUNCTIONS:
3799 Define this if you desire to only have use of the NS16550_init
3800 and NS16550_putc functions for the serial driver located at
3801 drivers/serial/ns16550.c. This option is useful for saving
3802 space for already greatly restricted images, including but not
3803 limited to NAND_SPL configurations.
3805 - CONFIG_DISPLAY_BOARDINFO
3806 Display information about the board that U-Boot is running on
3807 when U-Boot starts up. The board function checkboard() is called
3810 - CONFIG_DISPLAY_BOARDINFO_LATE
3811 Similar to the previous option, but display this information
3812 later, once stdio is running and output goes to the LCD, if
3815 Low Level (hardware related) configuration options:
3816 ---------------------------------------------------
3818 - CONFIG_SYS_CACHELINE_SIZE:
3819 Cache Line Size of the CPU.
3821 - CONFIG_SYS_DEFAULT_IMMR:
3822 Default address of the IMMR after system reset.
3824 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
3825 and RPXsuper) to be able to adjust the position of
3826 the IMMR register after a reset.
3828 - CONFIG_SYS_CCSRBAR_DEFAULT:
3829 Default (power-on reset) physical address of CCSR on Freescale
3832 - CONFIG_SYS_CCSRBAR:
3833 Virtual address of CCSR. On a 32-bit build, this is typically
3834 the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
3836 CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
3837 for cross-platform code that uses that macro instead.
3839 - CONFIG_SYS_CCSRBAR_PHYS:
3840 Physical address of CCSR. CCSR can be relocated to a new
3841 physical address, if desired. In this case, this macro should
3842 be set to that address. Otherwise, it should be set to the
3843 same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR
3844 is typically relocated on 36-bit builds. It is recommended
3845 that this macro be defined via the _HIGH and _LOW macros:
3847 #define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
3848 * 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)
3850 - CONFIG_SYS_CCSRBAR_PHYS_HIGH:
3851 Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically
3852 either 0 (32-bit build) or 0xF (36-bit build). This macro is
3853 used in assembly code, so it must not contain typecasts or
3854 integer size suffixes (e.g. "ULL").
3856 - CONFIG_SYS_CCSRBAR_PHYS_LOW:
3857 Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is
3858 used in assembly code, so it must not contain typecasts or
3859 integer size suffixes (e.g. "ULL").
3861 - CONFIG_SYS_CCSR_DO_NOT_RELOCATE:
3862 If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
3863 forced to a value that ensures that CCSR is not relocated.
3865 - Floppy Disk Support:
3866 CONFIG_SYS_FDC_DRIVE_NUMBER
3868 the default drive number (default value 0)
3870 CONFIG_SYS_ISA_IO_STRIDE
3872 defines the spacing between FDC chipset registers
3875 CONFIG_SYS_ISA_IO_OFFSET
3877 defines the offset of register from address. It
3878 depends on which part of the data bus is connected to
3879 the FDC chipset. (default value 0)
3881 If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
3882 CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
3885 if CONFIG_SYS_FDC_HW_INIT is defined, then the function
3886 fdc_hw_init() is called at the beginning of the FDC
3887 setup. fdc_hw_init() must be provided by the board
3888 source code. It is used to make hardware dependant
3892 Most IDE controllers were designed to be connected with PCI
3893 interface. Only few of them were designed for AHB interface.
3894 When software is doing ATA command and data transfer to
3895 IDE devices through IDE-AHB controller, some additional
3896 registers accessing to these kind of IDE-AHB controller
3899 - CONFIG_SYS_IMMR: Physical address of the Internal Memory.
3900 DO NOT CHANGE unless you know exactly what you're
3901 doing! (11-4) [MPC8xx/82xx systems only]
3903 - CONFIG_SYS_INIT_RAM_ADDR:
3905 Start address of memory area that can be used for
3906 initial data and stack; please note that this must be
3907 writable memory that is working WITHOUT special
3908 initialization, i. e. you CANNOT use normal RAM which
3909 will become available only after programming the
3910 memory controller and running certain initialization
3913 U-Boot uses the following memory types:
3914 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
3915 - MPC824X: data cache
3916 - PPC4xx: data cache
3918 - CONFIG_SYS_GBL_DATA_OFFSET:
3920 Offset of the initial data structure in the memory
3921 area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
3922 CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
3923 data is located at the end of the available space
3924 (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
3925 CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
3926 below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
3927 CONFIG_SYS_GBL_DATA_OFFSET) downward.
3930 On the MPC824X (or other systems that use the data
3931 cache for initial memory) the address chosen for
3932 CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must
3933 point to an otherwise UNUSED address space between
3934 the top of RAM and the start of the PCI space.
3936 - CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
3938 - CONFIG_SYS_SYPCR: System Protection Control (11-9)
3940 - CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
3942 - CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
3944 - CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
3946 - CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
3948 - CONFIG_SYS_OR_TIMING_SDRAM:
3951 - CONFIG_SYS_MAMR_PTA:
3952 periodic timer for refresh
3954 - CONFIG_SYS_DER: Debug Event Register (37-47)
3956 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
3957 CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
3958 CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
3959 CONFIG_SYS_BR1_PRELIM:
3960 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
3962 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
3963 CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM,
3964 CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
3965 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
3967 - CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
3968 CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
3969 Machine Mode Register and Memory Periodic Timer
3970 Prescaler definitions (SDRAM timing)
3972 - CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
3973 enable I2C microcode relocation patch (MPC8xx);
3974 define relocation offset in DPRAM [DSP2]
3976 - CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
3977 enable SMC microcode relocation patch (MPC8xx);
3978 define relocation offset in DPRAM [SMC1]
3980 - CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
3981 enable SPI microcode relocation patch (MPC8xx);
3982 define relocation offset in DPRAM [SCC4]
3984 - CONFIG_SYS_USE_OSCCLK:
3985 Use OSCM clock mode on MBX8xx board. Be careful,
3986 wrong setting might damage your board. Read
3987 doc/README.MBX before setting this variable!
3989 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
3990 Offset of the bootmode word in DPRAM used by post
3991 (Power On Self Tests). This definition overrides
3992 #define'd default value in commproc.h resp.
3995 - CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
3996 CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
3997 CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
3998 CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
3999 CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
4000 CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
4001 CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
4002 CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
4003 Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
4005 - CONFIG_PCI_DISABLE_PCIE:
4006 Disable PCI-Express on systems where it is supported but not
4009 - CONFIG_PCI_ENUM_ONLY
4010 Only scan through and get the devices on the busses.
4011 Don't do any setup work, presumably because someone or
4012 something has already done it, and we don't need to do it
4013 a second time. Useful for platforms that are pre-booted
4014 by coreboot or similar.
4016 - CONFIG_PCI_INDIRECT_BRIDGE:
4017 Enable support for indirect PCI bridges.
4020 Chip has SRIO or not
4023 Board has SRIO 1 port available
4026 Board has SRIO 2 port available
4028 - CONFIG_SRIO_PCIE_BOOT_MASTER
4029 Board can support master function for Boot from SRIO and PCIE
4031 - CONFIG_SYS_SRIOn_MEM_VIRT:
4032 Virtual Address of SRIO port 'n' memory region
4034 - CONFIG_SYS_SRIOn_MEM_PHYS:
4035 Physical Address of SRIO port 'n' memory region
4037 - CONFIG_SYS_SRIOn_MEM_SIZE:
4038 Size of SRIO port 'n' memory region
4040 - CONFIG_SYS_NAND_BUSWIDTH_16BIT
4041 Defined to tell the NAND controller that the NAND chip is using
4043 Not all NAND drivers use this symbol.
4044 Example of drivers that use it:
4045 - drivers/mtd/nand/ndfc.c
4046 - drivers/mtd/nand/mxc_nand.c
4048 - CONFIG_SYS_NDFC_EBC0_CFG
4049 Sets the EBC0_CFG register for the NDFC. If not defined
4050 a default value will be used.
4053 Get DDR timing information from an I2C EEPROM. Common
4054 with pluggable memory modules such as SODIMMs
4057 I2C address of the SPD EEPROM
4059 - CONFIG_SYS_SPD_BUS_NUM
4060 If SPD EEPROM is on an I2C bus other than the first
4061 one, specify here. Note that the value must resolve
4062 to something your driver can deal with.
4064 - CONFIG_SYS_DDR_RAW_TIMING
4065 Get DDR timing information from other than SPD. Common with
4066 soldered DDR chips onboard without SPD. DDR raw timing
4067 parameters are extracted from datasheet and hard-coded into
4068 header files or board specific files.
4070 - CONFIG_FSL_DDR_INTERACTIVE
4071 Enable interactive DDR debugging. See doc/README.fsl-ddr.
4073 - CONFIG_SYS_83XX_DDR_USES_CS0
4074 Only for 83xx systems. If specified, then DDR should
4075 be configured using CS0 and CS1 instead of CS2 and CS3.
4077 - CONFIG_ETHER_ON_FEC[12]
4078 Define to enable FEC[12] on a 8xx series processor.
4080 - CONFIG_FEC[12]_PHY
4081 Define to the hardcoded PHY address which corresponds
4082 to the given FEC; i. e.
4083 #define CONFIG_FEC1_PHY 4
4084 means that the PHY with address 4 is connected to FEC1
4086 When set to -1, means to probe for first available.
4088 - CONFIG_FEC[12]_PHY_NORXERR
4089 The PHY does not have a RXERR line (RMII only).
4090 (so program the FEC to ignore it).
4093 Enable RMII mode for all FECs.
4094 Note that this is a global option, we can't
4095 have one FEC in standard MII mode and another in RMII mode.
4097 - CONFIG_CRC32_VERIFY
4098 Add a verify option to the crc32 command.
4101 => crc32 -v <address> <count> <crc32>
4103 Where address/count indicate a memory area
4104 and crc32 is the correct crc32 which the
4108 Add the "loopw" memory command. This only takes effect if
4109 the memory commands are activated globally (CONFIG_CMD_MEM).
4112 Add the "mdc" and "mwc" memory commands. These are cyclic
4117 This command will print 4 bytes (10,11,12,13) each 500 ms.
4119 => mwc.l 100 12345678 10
4120 This command will write 12345678 to address 100 all 10 ms.
4122 This only takes effect if the memory commands are activated
4123 globally (CONFIG_CMD_MEM).
4125 - CONFIG_SKIP_LOWLEVEL_INIT
4126 [ARM, NDS32, MIPS only] If this variable is defined, then certain
4127 low level initializations (like setting up the memory
4128 controller) are omitted and/or U-Boot does not
4129 relocate itself into RAM.
4131 Normally this variable MUST NOT be defined. The only
4132 exception is when U-Boot is loaded (to RAM) by some
4133 other boot loader or by a debugger which performs
4134 these initializations itself.
4137 Modifies the behaviour of start.S when compiling a loader
4138 that is executed before the actual U-Boot. E.g. when
4139 compiling a NAND SPL.
4141 - CONFIG_SYS_MPC85XX_NO_RESETVEC
4142 Only for 85xx systems. If this variable is specified, the section
4143 .resetvec is not kept and the section .bootpg is placed in the
4144 previous 4k of the .text section.
4146 - CONFIG_ARCH_MAP_SYSMEM
4147 Generally U-Boot (and in particular the md command) uses
4148 effective address. It is therefore not necessary to regard
4149 U-Boot address as virtual addresses that need to be translated
4150 to physical addresses. However, sandbox requires this, since
4151 it maintains its own little RAM buffer which contains all
4152 addressable memory. This option causes some memory accesses
4153 to be mapped through map_sysmem() / unmap_sysmem().
4155 - CONFIG_USE_ARCH_MEMCPY
4156 CONFIG_USE_ARCH_MEMSET
4157 If these options are used a optimized version of memcpy/memset will
4158 be used if available. These functions may be faster under some
4159 conditions but may increase the binary size.
4161 - CONFIG_X86_RESET_VECTOR
4162 If defined, the x86 reset vector code is included. This is not
4163 needed when U-Boot is running from Coreboot.
4166 Defines the MPU clock speed (in MHz).
4168 NOTE : currently only supported on AM335x platforms.
4170 Freescale QE/FMAN Firmware Support:
4171 -----------------------------------
4173 The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
4174 loading of "firmware", which is encoded in the QE firmware binary format.
4175 This firmware often needs to be loaded during U-Boot booting, so macros
4176 are used to identify the storage device (NOR flash, SPI, etc) and the address
4179 - CONFIG_SYS_QE_FMAN_FW_ADDR
4180 The address in the storage device where the firmware is located. The
4181 meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
4184 - CONFIG_SYS_QE_FMAN_FW_LENGTH
4185 The maximum possible size of the firmware. The firmware binary format
4186 has a field that specifies the actual size of the firmware, but it
4187 might not be possible to read any part of the firmware unless some
4188 local storage is allocated to hold the entire firmware first.
4190 - CONFIG_SYS_QE_FMAN_FW_IN_NOR
4191 Specifies that QE/FMAN firmware is located in NOR flash, mapped as
4192 normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the
4193 virtual address in NOR flash.
4195 - CONFIG_SYS_QE_FMAN_FW_IN_NAND
4196 Specifies that QE/FMAN firmware is located in NAND flash.
4197 CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
4199 - CONFIG_SYS_QE_FMAN_FW_IN_MMC
4200 Specifies that QE/FMAN firmware is located on the primary SD/MMC
4201 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
4203 - CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
4204 Specifies that QE/FMAN firmware is located on the primary SPI
4205 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
4207 - CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
4208 Specifies that QE/FMAN firmware is located in the remote (master)
4209 memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
4210 can be mapped from slave TLB->slave LAW->slave SRIO or PCIE outbound
4211 window->master inbound window->master LAW->the ucode address in
4212 master's memory space.
4214 Building the Software:
4215 ======================
4217 Building U-Boot has been tested in several native build environments
4218 and in many different cross environments. Of course we cannot support
4219 all possibly existing versions of cross development tools in all
4220 (potentially obsolete) versions. In case of tool chain problems we
4221 recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
4222 which is extensively used to build and test U-Boot.
4224 If you are not using a native environment, it is assumed that you
4225 have GNU cross compiling tools available in your path. In this case,
4226 you must set the environment variable CROSS_COMPILE in your shell.
4227 Note that no changes to the Makefile or any other source files are
4228 necessary. For example using the ELDK on a 4xx CPU, please enter:
4230 $ CROSS_COMPILE=ppc_4xx-
4231 $ export CROSS_COMPILE
4233 Note: If you wish to generate Windows versions of the utilities in
4234 the tools directory you can use the MinGW toolchain
4235 (http://www.mingw.org). Set your HOST tools to the MinGW
4236 toolchain and execute 'make tools'. For example:
4238 $ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
4240 Binaries such as tools/mkimage.exe will be created which can
4241 be executed on computers running Windows.
4243 U-Boot is intended to be simple to build. After installing the
4244 sources you must configure U-Boot for one specific board type. This
4249 where "NAME_config" is the name of one of the existing configu-
4250 rations; see boards.cfg for supported names.
4252 Note: for some board special configuration names may exist; check if
4253 additional information is available from the board vendor; for
4254 instance, the TQM823L systems are available without (standard)
4255 or with LCD support. You can select such additional "features"
4256 when choosing the configuration, i. e.
4259 - will configure for a plain TQM823L, i. e. no LCD support
4261 make TQM823L_LCD_config
4262 - will configure for a TQM823L with U-Boot console on LCD
4267 Finally, type "make all", and you should get some working U-Boot
4268 images ready for download to / installation on your system:
4270 - "u-boot.bin" is a raw binary image
4271 - "u-boot" is an image in ELF binary format
4272 - "u-boot.srec" is in Motorola S-Record format
4274 By default the build is performed locally and the objects are saved
4275 in the source directory. One of the two methods can be used to change
4276 this behavior and build U-Boot to some external directory:
4278 1. Add O= to the make command line invocations:
4280 make O=/tmp/build distclean
4281 make O=/tmp/build NAME_config
4282 make O=/tmp/build all
4284 2. Set environment variable BUILD_DIR to point to the desired location:
4286 export BUILD_DIR=/tmp/build
4291 Note that the command line "O=" setting overrides the BUILD_DIR environment
4295 Please be aware that the Makefiles assume you are using GNU make, so
4296 for instance on NetBSD you might need to use "gmake" instead of
4300 If the system board that you have is not listed, then you will need
4301 to port U-Boot to your hardware platform. To do this, follow these
4304 1. Add a new configuration option for your board to the toplevel
4305 "boards.cfg" file, using the existing entries as examples.
4306 Follow the instructions there to keep the boards in order.
4307 2. Create a new directory to hold your board specific code. Add any
4308 files you need. In your board directory, you will need at least
4309 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
4310 3. Create a new configuration file "include/configs/<board>.h" for
4312 3. If you're porting U-Boot to a new CPU, then also create a new
4313 directory to hold your CPU specific code. Add any files you need.
4314 4. Run "make <board>_config" with your new name.
4315 5. Type "make", and you should get a working "u-boot.srec" file
4316 to be installed on your target system.
4317 6. Debug and solve any problems that might arise.
4318 [Of course, this last step is much harder than it sounds.]
4321 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
4322 ==============================================================
4324 If you have modified U-Boot sources (for instance added a new board
4325 or support for new devices, a new CPU, etc.) you are expected to
4326 provide feedback to the other developers. The feedback normally takes
4327 the form of a "patch", i. e. a context diff against a certain (latest
4328 official or latest in the git repository) version of U-Boot sources.
4330 But before you submit such a patch, please verify that your modifi-
4331 cation did not break existing code. At least make sure that *ALL* of
4332 the supported boards compile WITHOUT ANY compiler warnings. To do so,
4333 just run the "MAKEALL" script, which will configure and build U-Boot
4334 for ALL supported system. Be warned, this will take a while. You can
4335 select which (cross) compiler to use by passing a `CROSS_COMPILE'
4336 environment variable to the script, i. e. to use the ELDK cross tools
4339 CROSS_COMPILE=ppc_8xx- MAKEALL
4341 or to build on a native PowerPC system you can type
4343 CROSS_COMPILE=' ' MAKEALL
4345 When using the MAKEALL script, the default behaviour is to build
4346 U-Boot in the source directory. This location can be changed by
4347 setting the BUILD_DIR environment variable. Also, for each target
4348 built, the MAKEALL script saves two log files (<target>.ERR and
4349 <target>.MAKEALL) in the <source dir>/LOG directory. This default
4350 location can be changed by setting the MAKEALL_LOGDIR environment
4351 variable. For example:
4353 export BUILD_DIR=/tmp/build
4354 export MAKEALL_LOGDIR=/tmp/log
4355 CROSS_COMPILE=ppc_8xx- MAKEALL
4357 With the above settings build objects are saved in the /tmp/build,
4358 log files are saved in the /tmp/log and the source tree remains clean
4359 during the whole build process.
4362 See also "U-Boot Porting Guide" below.
4365 Monitor Commands - Overview:
4366 ============================
4368 go - start application at address 'addr'
4369 run - run commands in an environment variable
4370 bootm - boot application image from memory
4371 bootp - boot image via network using BootP/TFTP protocol
4372 bootz - boot zImage from memory
4373 tftpboot- boot image via network using TFTP protocol
4374 and env variables "ipaddr" and "serverip"
4375 (and eventually "gatewayip")
4376 tftpput - upload a file via network using TFTP protocol
4377 rarpboot- boot image via network using RARP/TFTP protocol
4378 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
4379 loads - load S-Record file over serial line
4380 loadb - load binary file over serial line (kermit mode)
4382 mm - memory modify (auto-incrementing)
4383 nm - memory modify (constant address)
4384 mw - memory write (fill)
4386 cmp - memory compare
4387 crc32 - checksum calculation
4388 i2c - I2C sub-system
4389 sspi - SPI utility commands
4390 base - print or set address offset
4391 printenv- print environment variables
4392 setenv - set environment variables
4393 saveenv - save environment variables to persistent storage
4394 protect - enable or disable FLASH write protection
4395 erase - erase FLASH memory
4396 flinfo - print FLASH memory information
4397 nand - NAND memory operations (see doc/README.nand)
4398 bdinfo - print Board Info structure
4399 iminfo - print header information for application image
4400 coninfo - print console devices and informations
4401 ide - IDE sub-system
4402 loop - infinite loop on address range
4403 loopw - infinite write loop on address range
4404 mtest - simple RAM test
4405 icache - enable or disable instruction cache
4406 dcache - enable or disable data cache
4407 reset - Perform RESET of the CPU
4408 echo - echo args to console
4409 version - print monitor version
4410 help - print online help
4411 ? - alias for 'help'
4414 Monitor Commands - Detailed Description:
4415 ========================================
4419 For now: just type "help <command>".
4422 Environment Variables:
4423 ======================
4425 U-Boot supports user configuration using Environment Variables which
4426 can be made persistent by saving to Flash memory.
4428 Environment Variables are set using "setenv", printed using
4429 "printenv", and saved to Flash using "saveenv". Using "setenv"
4430 without a value can be used to delete a variable from the
4431 environment. As long as you don't save the environment you are
4432 working with an in-memory copy. In case the Flash area containing the
4433 environment is erased by accident, a default environment is provided.
4435 Some configuration options can be set using Environment Variables.
4437 List of environment variables (most likely not complete):
4439 baudrate - see CONFIG_BAUDRATE
4441 bootdelay - see CONFIG_BOOTDELAY
4443 bootcmd - see CONFIG_BOOTCOMMAND
4445 bootargs - Boot arguments when booting an RTOS image
4447 bootfile - Name of the image to load with TFTP
4449 bootm_low - Memory range available for image processing in the bootm
4450 command can be restricted. This variable is given as
4451 a hexadecimal number and defines lowest address allowed
4452 for use by the bootm command. See also "bootm_size"
4453 environment variable. Address defined by "bootm_low" is
4454 also the base of the initial memory mapping for the Linux
4455 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
4458 bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
4459 This variable is given as a hexadecimal number and it
4460 defines the size of the memory region starting at base
4461 address bootm_low that is accessible by the Linux kernel
4462 during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
4463 as the default value if it is defined, and bootm_size is
4466 bootm_size - Memory range available for image processing in the bootm
4467 command can be restricted. This variable is given as
4468 a hexadecimal number and defines the size of the region
4469 allowed for use by the bootm command. See also "bootm_low"
4470 environment variable.
4472 updatefile - Location of the software update file on a TFTP server, used
4473 by the automatic software update feature. Please refer to
4474 documentation in doc/README.update for more details.
4476 autoload - if set to "no" (any string beginning with 'n'),
4477 "bootp" will just load perform a lookup of the
4478 configuration from the BOOTP server, but not try to
4479 load any image using TFTP
4481 autostart - if set to "yes", an image loaded using the "bootp",
4482 "rarpboot", "tftpboot" or "diskboot" commands will
4483 be automatically started (by internally calling
4486 If set to "no", a standalone image passed to the
4487 "bootm" command will be copied to the load address
4488 (and eventually uncompressed), but NOT be started.
4489 This can be used to load and uncompress arbitrary
4492 fdt_high - if set this restricts the maximum address that the
4493 flattened device tree will be copied into upon boot.
4494 For example, if you have a system with 1 GB memory
4495 at physical address 0x10000000, while Linux kernel
4496 only recognizes the first 704 MB as low memory, you
4497 may need to set fdt_high as 0x3C000000 to have the
4498 device tree blob be copied to the maximum address
4499 of the 704 MB low memory, so that Linux kernel can
4500 access it during the boot procedure.
4502 If this is set to the special value 0xFFFFFFFF then
4503 the fdt will not be copied at all on boot. For this
4504 to work it must reside in writable memory, have
4505 sufficient padding on the end of it for u-boot to
4506 add the information it needs into it, and the memory
4507 must be accessible by the kernel.
4509 fdtcontroladdr- if set this is the address of the control flattened
4510 device tree used by U-Boot when CONFIG_OF_CONTROL is
4513 i2cfast - (PPC405GP|PPC405EP only)
4514 if set to 'y' configures Linux I2C driver for fast
4515 mode (400kHZ). This environment variable is used in
4516 initialization code. So, for changes to be effective
4517 it must be saved and board must be reset.
4519 initrd_high - restrict positioning of initrd images:
4520 If this variable is not set, initrd images will be
4521 copied to the highest possible address in RAM; this
4522 is usually what you want since it allows for
4523 maximum initrd size. If for some reason you want to
4524 make sure that the initrd image is loaded below the
4525 CONFIG_SYS_BOOTMAPSZ limit, you can set this environment
4526 variable to a value of "no" or "off" or "0".
4527 Alternatively, you can set it to a maximum upper
4528 address to use (U-Boot will still check that it
4529 does not overwrite the U-Boot stack and data).
4531 For instance, when you have a system with 16 MB
4532 RAM, and want to reserve 4 MB from use by Linux,
4533 you can do this by adding "mem=12M" to the value of
4534 the "bootargs" variable. However, now you must make
4535 sure that the initrd image is placed in the first
4536 12 MB as well - this can be done with
4538 setenv initrd_high 00c00000
4540 If you set initrd_high to 0xFFFFFFFF, this is an
4541 indication to U-Boot that all addresses are legal
4542 for the Linux kernel, including addresses in flash
4543 memory. In this case U-Boot will NOT COPY the
4544 ramdisk at all. This may be useful to reduce the
4545 boot time on your system, but requires that this
4546 feature is supported by your Linux kernel.
4548 ipaddr - IP address; needed for tftpboot command
4550 loadaddr - Default load address for commands like "bootp",
4551 "rarpboot", "tftpboot", "loadb" or "diskboot"
4553 loads_echo - see CONFIG_LOADS_ECHO
4555 serverip - TFTP server IP address; needed for tftpboot command
4557 bootretry - see CONFIG_BOOT_RETRY_TIME
4559 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
4561 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
4563 ethprime - controls which interface is used first.
4565 ethact - controls which interface is currently active.
4566 For example you can do the following
4568 => setenv ethact FEC
4569 => ping 192.168.0.1 # traffic sent on FEC
4570 => setenv ethact SCC
4571 => ping 10.0.0.1 # traffic sent on SCC
4573 ethrotate - When set to "no" U-Boot does not go through all
4574 available network interfaces.
4575 It just stays at the currently selected interface.
4577 netretry - When set to "no" each network operation will
4578 either succeed or fail without retrying.
4579 When set to "once" the network operation will
4580 fail when all the available network interfaces
4581 are tried once without success.
4582 Useful on scripts which control the retry operation
4585 npe_ucode - set load address for the NPE microcode
4587 tftpsrcport - If this is set, the value is used for TFTP's
4590 tftpdstport - If this is set, the value is used for TFTP's UDP
4591 destination port instead of the Well Know Port 69.
4593 tftpblocksize - Block size to use for TFTP transfers; if not set,
4594 we use the TFTP server's default block size
4596 tftptimeout - Retransmission timeout for TFTP packets (in milli-
4597 seconds, minimum value is 1000 = 1 second). Defines
4598 when a packet is considered to be lost so it has to
4599 be retransmitted. The default is 5000 = 5 seconds.
4600 Lowering this value may make downloads succeed
4601 faster in networks with high packet loss rates or
4602 with unreliable TFTP servers.
4604 vlan - When set to a value < 4095 the traffic over
4605 Ethernet is encapsulated/received over 802.1q
4608 The following image location variables contain the location of images
4609 used in booting. The "Image" column gives the role of the image and is
4610 not an environment variable name. The other columns are environment
4611 variable names. "File Name" gives the name of the file on a TFTP
4612 server, "RAM Address" gives the location in RAM the image will be
4613 loaded to, and "Flash Location" gives the image's address in NOR
4614 flash or offset in NAND flash.
4616 *Note* - these variables don't have to be defined for all boards, some
4617 boards currenlty use other variables for these purposes, and some
4618 boards use these variables for other purposes.
4620 Image File Name RAM Address Flash Location
4621 ----- --------- ----------- --------------
4622 u-boot u-boot u-boot_addr_r u-boot_addr
4623 Linux kernel bootfile kernel_addr_r kernel_addr
4624 device tree blob fdtfile fdt_addr_r fdt_addr
4625 ramdisk ramdiskfile ramdisk_addr_r ramdisk_addr
4627 The following environment variables may be used and automatically
4628 updated by the network boot commands ("bootp" and "rarpboot"),
4629 depending the information provided by your boot server:
4631 bootfile - see above
4632 dnsip - IP address of your Domain Name Server
4633 dnsip2 - IP address of your secondary Domain Name Server
4634 gatewayip - IP address of the Gateway (Router) to use
4635 hostname - Target hostname
4637 netmask - Subnet Mask
4638 rootpath - Pathname of the root filesystem on the NFS server
4639 serverip - see above
4642 There are two special Environment Variables:
4644 serial# - contains hardware identification information such
4645 as type string and/or serial number
4646 ethaddr - Ethernet address
4648 These variables can be set only once (usually during manufacturing of
4649 the board). U-Boot refuses to delete or overwrite these variables
4650 once they have been set once.
4653 Further special Environment Variables:
4655 ver - Contains the U-Boot version string as printed
4656 with the "version" command. This variable is
4657 readonly (see CONFIG_VERSION_VARIABLE).
4660 Please note that changes to some configuration parameters may take
4661 only effect after the next boot (yes, that's just like Windoze :-).
4664 Callback functions for environment variables:
4665 ---------------------------------------------
4667 For some environment variables, the behavior of u-boot needs to change
4668 when their values are changed. This functionailty allows functions to
4669 be associated with arbitrary variables. On creation, overwrite, or
4670 deletion, the callback will provide the opportunity for some side
4671 effect to happen or for the change to be rejected.
4673 The callbacks are named and associated with a function using the
4674 U_BOOT_ENV_CALLBACK macro in your board or driver code.
4676 These callbacks are associated with variables in one of two ways. The
4677 static list can be added to by defining CONFIG_ENV_CALLBACK_LIST_STATIC
4678 in the board configuration to a string that defines a list of
4679 associations. The list must be in the following format:
4681 entry = variable_name[:callback_name]
4684 If the callback name is not specified, then the callback is deleted.
4685 Spaces are also allowed anywhere in the list.
4687 Callbacks can also be associated by defining the ".callbacks" variable
4688 with the same list format above. Any association in ".callbacks" will
4689 override any association in the static list. You can define
4690 CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the
4691 ".callbacks" envirnoment variable in the default or embedded environment.
4694 Command Line Parsing:
4695 =====================
4697 There are two different command line parsers available with U-Boot:
4698 the old "simple" one, and the much more powerful "hush" shell:
4700 Old, simple command line parser:
4701 --------------------------------
4703 - supports environment variables (through setenv / saveenv commands)
4704 - several commands on one line, separated by ';'
4705 - variable substitution using "... ${name} ..." syntax
4706 - special characters ('$', ';') can be escaped by prefixing with '\',
4708 setenv bootcmd bootm \${address}
4709 - You can also escape text by enclosing in single apostrophes, for example:
4710 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
4715 - similar to Bourne shell, with control structures like
4716 if...then...else...fi, for...do...done; while...do...done,
4717 until...do...done, ...
4718 - supports environment ("global") variables (through setenv / saveenv
4719 commands) and local shell variables (through standard shell syntax
4720 "name=value"); only environment variables can be used with "run"
4726 (1) If a command line (or an environment variable executed by a "run"
4727 command) contains several commands separated by semicolon, and
4728 one of these commands fails, then the remaining commands will be
4731 (2) If you execute several variables with one call to run (i. e.
4732 calling run with a list of variables as arguments), any failing
4733 command will cause "run" to terminate, i. e. the remaining
4734 variables are not executed.
4736 Note for Redundant Ethernet Interfaces:
4737 =======================================
4739 Some boards come with redundant Ethernet interfaces; U-Boot supports
4740 such configurations and is capable of automatic selection of a
4741 "working" interface when needed. MAC assignment works as follows:
4743 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
4744 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
4745 "eth1addr" (=>eth1), "eth2addr", ...
4747 If the network interface stores some valid MAC address (for instance
4748 in SROM), this is used as default address if there is NO correspon-
4749 ding setting in the environment; if the corresponding environment
4750 variable is set, this overrides the settings in the card; that means:
4752 o If the SROM has a valid MAC address, and there is no address in the
4753 environment, the SROM's address is used.
4755 o If there is no valid address in the SROM, and a definition in the
4756 environment exists, then the value from the environment variable is
4759 o If both the SROM and the environment contain a MAC address, and
4760 both addresses are the same, this MAC address is used.
4762 o If both the SROM and the environment contain a MAC address, and the
4763 addresses differ, the value from the environment is used and a
4766 o If neither SROM nor the environment contain a MAC address, an error
4769 If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
4770 will be programmed into hardware as part of the initialization process. This
4771 may be skipped by setting the appropriate 'ethmacskip' environment variable.
4772 The naming convention is as follows:
4773 "ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
4778 U-Boot is capable of booting (and performing other auxiliary operations on)
4779 images in two formats:
4781 New uImage format (FIT)
4782 -----------------------
4784 Flexible and powerful format based on Flattened Image Tree -- FIT (similar
4785 to Flattened Device Tree). It allows the use of images with multiple
4786 components (several kernels, ramdisks, etc.), with contents protected by
4787 SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
4793 Old image format is based on binary files which can be basically anything,
4794 preceded by a special header; see the definitions in include/image.h for
4795 details; basically, the header defines the following image properties:
4797 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
4798 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
4799 LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
4800 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
4802 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
4803 IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
4804 Currently supported: ARM, AVR32, Intel x86, MIPS, NDS32, Nios II, PowerPC).
4805 * Compression Type (uncompressed, gzip, bzip2)
4811 The header is marked by a special Magic Number, and both the header
4812 and the data portions of the image are secured against corruption by
4819 Although U-Boot should support any OS or standalone application
4820 easily, the main focus has always been on Linux during the design of
4823 U-Boot includes many features that so far have been part of some
4824 special "boot loader" code within the Linux kernel. Also, any
4825 "initrd" images to be used are no longer part of one big Linux image;
4826 instead, kernel and "initrd" are separate images. This implementation
4827 serves several purposes:
4829 - the same features can be used for other OS or standalone
4830 applications (for instance: using compressed images to reduce the
4831 Flash memory footprint)
4833 - it becomes much easier to port new Linux kernel versions because
4834 lots of low-level, hardware dependent stuff are done by U-Boot
4836 - the same Linux kernel image can now be used with different "initrd"
4837 images; of course this also means that different kernel images can
4838 be run with the same "initrd". This makes testing easier (you don't
4839 have to build a new "zImage.initrd" Linux image when you just
4840 change a file in your "initrd"). Also, a field-upgrade of the
4841 software is easier now.
4847 Porting Linux to U-Boot based systems:
4848 ---------------------------------------
4850 U-Boot cannot save you from doing all the necessary modifications to
4851 configure the Linux device drivers for use with your target hardware
4852 (no, we don't intend to provide a full virtual machine interface to
4855 But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
4857 Just make sure your machine specific header file (for instance
4858 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
4859 Information structure as we define in include/asm-<arch>/u-boot.h,
4860 and make sure that your definition of IMAP_ADDR uses the same value
4861 as your U-Boot configuration in CONFIG_SYS_IMMR.
4864 Configuring the Linux kernel:
4865 -----------------------------
4867 No specific requirements for U-Boot. Make sure you have some root
4868 device (initial ramdisk, NFS) for your target system.
4871 Building a Linux Image:
4872 -----------------------
4874 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
4875 not used. If you use recent kernel source, a new build target
4876 "uImage" will exist which automatically builds an image usable by
4877 U-Boot. Most older kernels also have support for a "pImage" target,
4878 which was introduced for our predecessor project PPCBoot and uses a
4879 100% compatible format.
4888 The "uImage" build target uses a special tool (in 'tools/mkimage') to
4889 encapsulate a compressed Linux kernel image with header information,
4890 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
4892 * build a standard "vmlinux" kernel image (in ELF binary format):
4894 * convert the kernel into a raw binary image:
4896 ${CROSS_COMPILE}-objcopy -O binary \
4897 -R .note -R .comment \
4898 -S vmlinux linux.bin
4900 * compress the binary image:
4904 * package compressed binary image for U-Boot:
4906 mkimage -A ppc -O linux -T kernel -C gzip \
4907 -a 0 -e 0 -n "Linux Kernel Image" \
4908 -d linux.bin.gz uImage
4911 The "mkimage" tool can also be used to create ramdisk images for use
4912 with U-Boot, either separated from the Linux kernel image, or
4913 combined into one file. "mkimage" encapsulates the images with a 64
4914 byte header containing information about target architecture,
4915 operating system, image type, compression method, entry points, time
4916 stamp, CRC32 checksums, etc.
4918 "mkimage" can be called in two ways: to verify existing images and
4919 print the header information, or to build new images.
4921 In the first form (with "-l" option) mkimage lists the information
4922 contained in the header of an existing U-Boot image; this includes
4923 checksum verification:
4925 tools/mkimage -l image
4926 -l ==> list image header information
4928 The second form (with "-d" option) is used to build a U-Boot image
4929 from a "data file" which is used as image payload:
4931 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
4932 -n name -d data_file image
4933 -A ==> set architecture to 'arch'
4934 -O ==> set operating system to 'os'
4935 -T ==> set image type to 'type'
4936 -C ==> set compression type 'comp'
4937 -a ==> set load address to 'addr' (hex)
4938 -e ==> set entry point to 'ep' (hex)
4939 -n ==> set image name to 'name'
4940 -d ==> use image data from 'datafile'
4942 Right now, all Linux kernels for PowerPC systems use the same load
4943 address (0x00000000), but the entry point address depends on the
4946 - 2.2.x kernels have the entry point at 0x0000000C,
4947 - 2.3.x and later kernels have the entry point at 0x00000000.
4949 So a typical call to build a U-Boot image would read:
4951 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
4952 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
4953 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
4954 > examples/uImage.TQM850L
4955 Image Name: 2.4.4 kernel for TQM850L
4956 Created: Wed Jul 19 02:34:59 2000
4957 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4958 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
4959 Load Address: 0x00000000
4960 Entry Point: 0x00000000
4962 To verify the contents of the image (or check for corruption):
4964 -> tools/mkimage -l examples/uImage.TQM850L
4965 Image Name: 2.4.4 kernel for TQM850L
4966 Created: Wed Jul 19 02:34:59 2000
4967 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4968 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
4969 Load Address: 0x00000000
4970 Entry Point: 0x00000000
4972 NOTE: for embedded systems where boot time is critical you can trade
4973 speed for memory and install an UNCOMPRESSED image instead: this
4974 needs more space in Flash, but boots much faster since it does not
4975 need to be uncompressed:
4977 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
4978 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
4979 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
4980 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
4981 > examples/uImage.TQM850L-uncompressed
4982 Image Name: 2.4.4 kernel for TQM850L
4983 Created: Wed Jul 19 02:34:59 2000
4984 Image Type: PowerPC Linux Kernel Image (uncompressed)
4985 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
4986 Load Address: 0x00000000
4987 Entry Point: 0x00000000
4990 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
4991 when your kernel is intended to use an initial ramdisk:
4993 -> tools/mkimage -n 'Simple Ramdisk Image' \
4994 > -A ppc -O linux -T ramdisk -C gzip \
4995 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
4996 Image Name: Simple Ramdisk Image
4997 Created: Wed Jan 12 14:01:50 2000
4998 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4999 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
5000 Load Address: 0x00000000
5001 Entry Point: 0x00000000
5004 Installing a Linux Image:
5005 -------------------------
5007 To downloading a U-Boot image over the serial (console) interface,
5008 you must convert the image to S-Record format:
5010 objcopy -I binary -O srec examples/image examples/image.srec
5012 The 'objcopy' does not understand the information in the U-Boot
5013 image header, so the resulting S-Record file will be relative to
5014 address 0x00000000. To load it to a given address, you need to
5015 specify the target address as 'offset' parameter with the 'loads'
5018 Example: install the image to address 0x40100000 (which on the
5019 TQM8xxL is in the first Flash bank):
5021 => erase 40100000 401FFFFF
5027 ## Ready for S-Record download ...
5028 ~>examples/image.srec
5029 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
5031 15989 15990 15991 15992
5032 [file transfer complete]
5034 ## Start Addr = 0x00000000
5037 You can check the success of the download using the 'iminfo' command;
5038 this includes a checksum verification so you can be sure no data
5039 corruption happened:
5043 ## Checking Image at 40100000 ...
5044 Image Name: 2.2.13 for initrd on TQM850L
5045 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5046 Data Size: 335725 Bytes = 327 kB = 0 MB
5047 Load Address: 00000000
5048 Entry Point: 0000000c
5049 Verifying Checksum ... OK
5055 The "bootm" command is used to boot an application that is stored in
5056 memory (RAM or Flash). In case of a Linux kernel image, the contents
5057 of the "bootargs" environment variable is passed to the kernel as
5058 parameters. You can check and modify this variable using the
5059 "printenv" and "setenv" commands:
5062 => printenv bootargs
5063 bootargs=root=/dev/ram
5065 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5067 => printenv bootargs
5068 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5071 ## Booting Linux kernel at 40020000 ...
5072 Image Name: 2.2.13 for NFS on TQM850L
5073 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5074 Data Size: 381681 Bytes = 372 kB = 0 MB
5075 Load Address: 00000000
5076 Entry Point: 0000000c
5077 Verifying Checksum ... OK
5078 Uncompressing Kernel Image ... OK
5079 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
5080 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5081 time_init: decrementer frequency = 187500000/60
5082 Calibrating delay loop... 49.77 BogoMIPS
5083 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
5086 If you want to boot a Linux kernel with initial RAM disk, you pass
5087 the memory addresses of both the kernel and the initrd image (PPBCOOT
5088 format!) to the "bootm" command:
5090 => imi 40100000 40200000
5092 ## Checking Image at 40100000 ...
5093 Image Name: 2.2.13 for initrd on TQM850L
5094 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5095 Data Size: 335725 Bytes = 327 kB = 0 MB
5096 Load Address: 00000000
5097 Entry Point: 0000000c
5098 Verifying Checksum ... OK
5100 ## Checking Image at 40200000 ...
5101 Image Name: Simple Ramdisk Image
5102 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5103 Data Size: 566530 Bytes = 553 kB = 0 MB
5104 Load Address: 00000000
5105 Entry Point: 00000000
5106 Verifying Checksum ... OK
5108 => bootm 40100000 40200000
5109 ## Booting Linux kernel at 40100000 ...
5110 Image Name: 2.2.13 for initrd on TQM850L
5111 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5112 Data Size: 335725 Bytes = 327 kB = 0 MB
5113 Load Address: 00000000
5114 Entry Point: 0000000c
5115 Verifying Checksum ... OK
5116 Uncompressing Kernel Image ... OK
5117 ## Loading RAMDisk Image at 40200000 ...
5118 Image Name: Simple Ramdisk Image
5119 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5120 Data Size: 566530 Bytes = 553 kB = 0 MB
5121 Load Address: 00000000
5122 Entry Point: 00000000
5123 Verifying Checksum ... OK
5124 Loading Ramdisk ... OK
5125 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
5126 Boot arguments: root=/dev/ram
5127 time_init: decrementer frequency = 187500000/60
5128 Calibrating delay loop... 49.77 BogoMIPS
5130 RAMDISK: Compressed image found at block 0
5131 VFS: Mounted root (ext2 filesystem).
5135 Boot Linux and pass a flat device tree:
5138 First, U-Boot must be compiled with the appropriate defines. See the section
5139 titled "Linux Kernel Interface" above for a more in depth explanation. The
5140 following is an example of how to start a kernel and pass an updated
5146 oft=oftrees/mpc8540ads.dtb
5147 => tftp $oftaddr $oft
5148 Speed: 1000, full duplex
5150 TFTP from server 192.168.1.1; our IP address is 192.168.1.101
5151 Filename 'oftrees/mpc8540ads.dtb'.
5152 Load address: 0x300000
5155 Bytes transferred = 4106 (100a hex)
5156 => tftp $loadaddr $bootfile
5157 Speed: 1000, full duplex
5159 TFTP from server 192.168.1.1; our IP address is 192.168.1.2
5161 Load address: 0x200000
5162 Loading:############
5164 Bytes transferred = 1029407 (fb51f hex)
5169 => bootm $loadaddr - $oftaddr
5170 ## Booting image at 00200000 ...
5171 Image Name: Linux-2.6.17-dirty
5172 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5173 Data Size: 1029343 Bytes = 1005.2 kB
5174 Load Address: 00000000
5175 Entry Point: 00000000
5176 Verifying Checksum ... OK
5177 Uncompressing Kernel Image ... OK
5178 Booting using flat device tree at 0x300000
5179 Using MPC85xx ADS machine description
5180 Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
5184 More About U-Boot Image Types:
5185 ------------------------------
5187 U-Boot supports the following image types:
5189 "Standalone Programs" are directly runnable in the environment
5190 provided by U-Boot; it is expected that (if they behave
5191 well) you can continue to work in U-Boot after return from
5192 the Standalone Program.
5193 "OS Kernel Images" are usually images of some Embedded OS which
5194 will take over control completely. Usually these programs
5195 will install their own set of exception handlers, device
5196 drivers, set up the MMU, etc. - this means, that you cannot
5197 expect to re-enter U-Boot except by resetting the CPU.
5198 "RAMDisk Images" are more or less just data blocks, and their
5199 parameters (address, size) are passed to an OS kernel that is
5201 "Multi-File Images" contain several images, typically an OS
5202 (Linux) kernel image and one or more data images like
5203 RAMDisks. This construct is useful for instance when you want
5204 to boot over the network using BOOTP etc., where the boot
5205 server provides just a single image file, but you want to get
5206 for instance an OS kernel and a RAMDisk image.
5208 "Multi-File Images" start with a list of image sizes, each
5209 image size (in bytes) specified by an "uint32_t" in network
5210 byte order. This list is terminated by an "(uint32_t)0".
5211 Immediately after the terminating 0 follow the images, one by
5212 one, all aligned on "uint32_t" boundaries (size rounded up to
5213 a multiple of 4 bytes).
5215 "Firmware Images" are binary images containing firmware (like
5216 U-Boot or FPGA images) which usually will be programmed to
5219 "Script files" are command sequences that will be executed by
5220 U-Boot's command interpreter; this feature is especially
5221 useful when you configure U-Boot to use a real shell (hush)
5222 as command interpreter.
5224 Booting the Linux zImage:
5225 -------------------------
5227 On some platforms, it's possible to boot Linux zImage. This is done
5228 using the "bootz" command. The syntax of "bootz" command is the same
5229 as the syntax of "bootm" command.
5231 Note, defining the CONFIG_SUPPORT_RAW_INITRD allows user to supply
5232 kernel with raw initrd images. The syntax is slightly different, the
5233 address of the initrd must be augmented by it's size, in the following
5234 format: "<initrd addres>:<initrd size>".
5240 One of the features of U-Boot is that you can dynamically load and
5241 run "standalone" applications, which can use some resources of
5242 U-Boot like console I/O functions or interrupt services.
5244 Two simple examples are included with the sources:
5249 'examples/hello_world.c' contains a small "Hello World" Demo
5250 application; it is automatically compiled when you build U-Boot.
5251 It's configured to run at address 0x00040004, so you can play with it
5255 ## Ready for S-Record download ...
5256 ~>examples/hello_world.srec
5257 1 2 3 4 5 6 7 8 9 10 11 ...
5258 [file transfer complete]
5260 ## Start Addr = 0x00040004
5262 => go 40004 Hello World! This is a test.
5263 ## Starting application at 0x00040004 ...
5274 Hit any key to exit ...
5276 ## Application terminated, rc = 0x0
5278 Another example, which demonstrates how to register a CPM interrupt
5279 handler with the U-Boot code, can be found in 'examples/timer.c'.
5280 Here, a CPM timer is set up to generate an interrupt every second.
5281 The interrupt service routine is trivial, just printing a '.'
5282 character, but this is just a demo program. The application can be
5283 controlled by the following keys:
5285 ? - print current values og the CPM Timer registers
5286 b - enable interrupts and start timer
5287 e - stop timer and disable interrupts
5288 q - quit application
5291 ## Ready for S-Record download ...
5292 ~>examples/timer.srec
5293 1 2 3 4 5 6 7 8 9 10 11 ...
5294 [file transfer complete]
5296 ## Start Addr = 0x00040004
5299 ## Starting application at 0x00040004 ...
5302 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
5305 [q, b, e, ?] Set interval 1000000 us
5308 [q, b, e, ?] ........
5309 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
5312 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
5315 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
5318 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
5320 [q, b, e, ?] ...Stopping timer
5322 [q, b, e, ?] ## Application terminated, rc = 0x0
5328 Over time, many people have reported problems when trying to use the
5329 "minicom" terminal emulation program for serial download. I (wd)
5330 consider minicom to be broken, and recommend not to use it. Under
5331 Unix, I recommend to use C-Kermit for general purpose use (and
5332 especially for kermit binary protocol download ("loadb" command), and
5333 use "cu" for S-Record download ("loads" command). See
5334 http://www.denx.de/wiki/view/DULG/SystemSetup#Section_4.3.
5335 for help with kermit.
5338 Nevertheless, if you absolutely want to use it try adding this
5339 configuration to your "File transfer protocols" section:
5341 Name Program Name U/D FullScr IO-Red. Multi
5342 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
5343 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
5349 Starting at version 0.9.2, U-Boot supports NetBSD both as host
5350 (build U-Boot) and target system (boots NetBSD/mpc8xx).
5352 Building requires a cross environment; it is known to work on
5353 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
5354 need gmake since the Makefiles are not compatible with BSD make).
5355 Note that the cross-powerpc package does not install include files;
5356 attempting to build U-Boot will fail because <machine/ansi.h> is
5357 missing. This file has to be installed and patched manually:
5359 # cd /usr/pkg/cross/powerpc-netbsd/include
5361 # ln -s powerpc machine
5362 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
5363 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
5365 Native builds *don't* work due to incompatibilities between native
5366 and U-Boot include files.
5368 Booting assumes that (the first part of) the image booted is a
5369 stage-2 loader which in turn loads and then invokes the kernel
5370 proper. Loader sources will eventually appear in the NetBSD source
5371 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
5372 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
5375 Implementation Internals:
5376 =========================
5378 The following is not intended to be a complete description of every
5379 implementation detail. However, it should help to understand the
5380 inner workings of U-Boot and make it easier to port it to custom
5384 Initial Stack, Global Data:
5385 ---------------------------
5387 The implementation of U-Boot is complicated by the fact that U-Boot
5388 starts running out of ROM (flash memory), usually without access to
5389 system RAM (because the memory controller is not initialized yet).
5390 This means that we don't have writable Data or BSS segments, and BSS
5391 is not initialized as zero. To be able to get a C environment working
5392 at all, we have to allocate at least a minimal stack. Implementation
5393 options for this are defined and restricted by the CPU used: Some CPU
5394 models provide on-chip memory (like the IMMR area on MPC8xx and
5395 MPC826x processors), on others (parts of) the data cache can be
5396 locked as (mis-) used as memory, etc.
5398 Chris Hallinan posted a good summary of these issues to the
5399 U-Boot mailing list:
5401 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
5402 From: "Chris Hallinan" <clh@net1plus.com>
5403 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
5406 Correct me if I'm wrong, folks, but the way I understand it
5407 is this: Using DCACHE as initial RAM for Stack, etc, does not
5408 require any physical RAM backing up the cache. The cleverness
5409 is that the cache is being used as a temporary supply of
5410 necessary storage before the SDRAM controller is setup. It's
5411 beyond the scope of this list to explain the details, but you
5412 can see how this works by studying the cache architecture and
5413 operation in the architecture and processor-specific manuals.
5415 OCM is On Chip Memory, which I believe the 405GP has 4K. It
5416 is another option for the system designer to use as an
5417 initial stack/RAM area prior to SDRAM being available. Either
5418 option should work for you. Using CS 4 should be fine if your
5419 board designers haven't used it for something that would
5420 cause you grief during the initial boot! It is frequently not
5423 CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere
5424 with your processor/board/system design. The default value
5425 you will find in any recent u-boot distribution in
5426 walnut.h should work for you. I'd set it to a value larger
5427 than your SDRAM module. If you have a 64MB SDRAM module, set
5428 it above 400_0000. Just make sure your board has no resources
5429 that are supposed to respond to that address! That code in
5430 start.S has been around a while and should work as is when
5431 you get the config right.
5436 It is essential to remember this, since it has some impact on the C
5437 code for the initialization procedures:
5439 * Initialized global data (data segment) is read-only. Do not attempt
5442 * Do not use any uninitialized global data (or implicitely initialized
5443 as zero data - BSS segment) at all - this is undefined, initiali-
5444 zation is performed later (when relocating to RAM).
5446 * Stack space is very limited. Avoid big data buffers or things like
5449 Having only the stack as writable memory limits means we cannot use
5450 normal global data to share information beween the code. But it
5451 turned out that the implementation of U-Boot can be greatly
5452 simplified by making a global data structure (gd_t) available to all
5453 functions. We could pass a pointer to this data as argument to _all_
5454 functions, but this would bloat the code. Instead we use a feature of
5455 the GCC compiler (Global Register Variables) to share the data: we
5456 place a pointer (gd) to the global data into a register which we
5457 reserve for this purpose.
5459 When choosing a register for such a purpose we are restricted by the
5460 relevant (E)ABI specifications for the current architecture, and by
5461 GCC's implementation.
5463 For PowerPC, the following registers have specific use:
5465 R2: reserved for system use
5466 R3-R4: parameter passing and return values
5467 R5-R10: parameter passing
5468 R13: small data area pointer
5472 (U-Boot also uses R12 as internal GOT pointer. r12
5473 is a volatile register so r12 needs to be reset when
5474 going back and forth between asm and C)
5476 ==> U-Boot will use R2 to hold a pointer to the global data
5478 Note: on PPC, we could use a static initializer (since the
5479 address of the global data structure is known at compile time),
5480 but it turned out that reserving a register results in somewhat
5481 smaller code - although the code savings are not that big (on
5482 average for all boards 752 bytes for the whole U-Boot image,
5483 624 text + 127 data).
5485 On Blackfin, the normal C ABI (except for P3) is followed as documented here:
5486 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
5488 ==> U-Boot will use P3 to hold a pointer to the global data
5490 On ARM, the following registers are used:
5492 R0: function argument word/integer result
5493 R1-R3: function argument word
5495 R10: stack limit (used only if stack checking if enabled)
5496 R11: argument (frame) pointer
5497 R12: temporary workspace
5500 R15: program counter
5502 ==> U-Boot will use R8 to hold a pointer to the global data
5504 On Nios II, the ABI is documented here:
5505 http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
5507 ==> U-Boot will use gp to hold a pointer to the global data
5509 Note: on Nios II, we give "-G0" option to gcc and don't use gp
5510 to access small data sections, so gp is free.
5512 On NDS32, the following registers are used:
5514 R0-R1: argument/return
5516 R15: temporary register for assembler
5517 R16: trampoline register
5518 R28: frame pointer (FP)
5519 R29: global pointer (GP)
5520 R30: link register (LP)
5521 R31: stack pointer (SP)
5522 PC: program counter (PC)
5524 ==> U-Boot will use R10 to hold a pointer to the global data
5526 NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
5527 or current versions of GCC may "optimize" the code too much.
5532 U-Boot runs in system state and uses physical addresses, i.e. the
5533 MMU is not used either for address mapping nor for memory protection.
5535 The available memory is mapped to fixed addresses using the memory
5536 controller. In this process, a contiguous block is formed for each
5537 memory type (Flash, SDRAM, SRAM), even when it consists of several
5538 physical memory banks.
5540 U-Boot is installed in the first 128 kB of the first Flash bank (on
5541 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
5542 booting and sizing and initializing DRAM, the code relocates itself
5543 to the upper end of DRAM. Immediately below the U-Boot code some
5544 memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN
5545 configuration setting]. Below that, a structure with global Board
5546 Info data is placed, followed by the stack (growing downward).
5548 Additionally, some exception handler code is copied to the low 8 kB
5549 of DRAM (0x00000000 ... 0x00001FFF).
5551 So a typical memory configuration with 16 MB of DRAM could look like
5554 0x0000 0000 Exception Vector code
5557 0x0000 2000 Free for Application Use
5563 0x00FB FF20 Monitor Stack (Growing downward)
5564 0x00FB FFAC Board Info Data and permanent copy of global data
5565 0x00FC 0000 Malloc Arena
5568 0x00FE 0000 RAM Copy of Monitor Code
5569 ... eventually: LCD or video framebuffer
5570 ... eventually: pRAM (Protected RAM - unchanged by reset)
5571 0x00FF FFFF [End of RAM]
5574 System Initialization:
5575 ----------------------
5577 In the reset configuration, U-Boot starts at the reset entry point
5578 (on most PowerPC systems at address 0x00000100). Because of the reset
5579 configuration for CS0# this is a mirror of the onboard Flash memory.
5580 To be able to re-map memory U-Boot then jumps to its link address.
5581 To be able to implement the initialization code in C, a (small!)
5582 initial stack is set up in the internal Dual Ported RAM (in case CPUs
5583 which provide such a feature like MPC8xx or MPC8260), or in a locked
5584 part of the data cache. After that, U-Boot initializes the CPU core,
5585 the caches and the SIU.
5587 Next, all (potentially) available memory banks are mapped using a
5588 preliminary mapping. For example, we put them on 512 MB boundaries
5589 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
5590 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
5591 programmed for SDRAM access. Using the temporary configuration, a
5592 simple memory test is run that determines the size of the SDRAM
5595 When there is more than one SDRAM bank, and the banks are of
5596 different size, the largest is mapped first. For equal size, the first
5597 bank (CS2#) is mapped first. The first mapping is always for address
5598 0x00000000, with any additional banks following immediately to create
5599 contiguous memory starting from 0.
5601 Then, the monitor installs itself at the upper end of the SDRAM area
5602 and allocates memory for use by malloc() and for the global Board
5603 Info data; also, the exception vector code is copied to the low RAM
5604 pages, and the final stack is set up.
5606 Only after this relocation will you have a "normal" C environment;
5607 until that you are restricted in several ways, mostly because you are
5608 running from ROM, and because the code will have to be relocated to a
5612 U-Boot Porting Guide:
5613 ----------------------
5615 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
5619 int main(int argc, char *argv[])
5621 sighandler_t no_more_time;
5623 signal(SIGALRM, no_more_time);
5624 alarm(PROJECT_DEADLINE - toSec (3 * WEEK));
5626 if (available_money > available_manpower) {
5627 Pay consultant to port U-Boot;
5631 Download latest U-Boot source;
5633 Subscribe to u-boot mailing list;
5636 email("Hi, I am new to U-Boot, how do I get started?");
5639 Read the README file in the top level directory;
5640 Read http://www.denx.de/twiki/bin/view/DULG/Manual;
5641 Read applicable doc/*.README;
5642 Read the source, Luke;
5643 /* find . -name "*.[chS]" | xargs grep -i <keyword> */
5646 if (available_money > toLocalCurrency ($2500))
5649 Add a lot of aggravation and time;
5651 if (a similar board exists) { /* hopefully... */
5652 cp -a board/<similar> board/<myboard>
5653 cp include/configs/<similar>.h include/configs/<myboard>.h
5655 Create your own board support subdirectory;
5656 Create your own board include/configs/<myboard>.h file;
5658 Edit new board/<myboard> files
5659 Edit new include/configs/<myboard>.h
5664 Add / modify source code;
5668 email("Hi, I am having problems...");
5670 Send patch file to the U-Boot email list;
5671 if (reasonable critiques)
5672 Incorporate improvements from email list code review;
5674 Defend code as written;
5680 void no_more_time (int sig)
5689 All contributions to U-Boot should conform to the Linux kernel
5690 coding style; see the file "Documentation/CodingStyle" and the script
5691 "scripts/Lindent" in your Linux kernel source directory.
5693 Source files originating from a different project (for example the
5694 MTD subsystem) are generally exempt from these guidelines and are not
5695 reformated to ease subsequent migration to newer versions of those
5698 Please note that U-Boot is implemented in C (and to some small parts in
5699 Assembler); no C++ is used, so please do not use C++ style comments (//)
5702 Please also stick to the following formatting rules:
5703 - remove any trailing white space
5704 - use TAB characters for indentation and vertical alignment, not spaces
5705 - make sure NOT to use DOS '\r\n' line feeds
5706 - do not add more than 2 consecutive empty lines to source files
5707 - do not add trailing empty lines to source files
5709 Submissions which do not conform to the standards may be returned
5710 with a request to reformat the changes.
5716 Since the number of patches for U-Boot is growing, we need to
5717 establish some rules. Submissions which do not conform to these rules
5718 may be rejected, even when they contain important and valuable stuff.
5720 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
5722 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
5723 see http://lists.denx.de/mailman/listinfo/u-boot
5725 When you send a patch, please include the following information with
5728 * For bug fixes: a description of the bug and how your patch fixes
5729 this bug. Please try to include a way of demonstrating that the
5730 patch actually fixes something.
5732 * For new features: a description of the feature and your
5735 * A CHANGELOG entry as plaintext (separate from the patch)
5737 * For major contributions, your entry to the CREDITS file
5739 * When you add support for a new board, don't forget to add this
5740 board to the MAINTAINERS file, too.
5742 * If your patch adds new configuration options, don't forget to
5743 document these in the README file.
5745 * The patch itself. If you are using git (which is *strongly*
5746 recommended) you can easily generate the patch using the
5747 "git format-patch". If you then use "git send-email" to send it to
5748 the U-Boot mailing list, you will avoid most of the common problems
5749 with some other mail clients.
5751 If you cannot use git, use "diff -purN OLD NEW". If your version of
5752 diff does not support these options, then get the latest version of
5755 The current directory when running this command shall be the parent
5756 directory of the U-Boot source tree (i. e. please make sure that
5757 your patch includes sufficient directory information for the
5760 We prefer patches as plain text. MIME attachments are discouraged,
5761 and compressed attachments must not be used.
5763 * If one logical set of modifications affects or creates several
5764 files, all these changes shall be submitted in a SINGLE patch file.
5766 * Changesets that contain different, unrelated modifications shall be
5767 submitted as SEPARATE patches, one patch per changeset.
5772 * Before sending the patch, run the MAKEALL script on your patched
5773 source tree and make sure that no errors or warnings are reported
5774 for any of the boards.
5776 * Keep your modifications to the necessary minimum: A patch
5777 containing several unrelated changes or arbitrary reformats will be
5778 returned with a request to re-formatting / split it.
5780 * If you modify existing code, make sure that your new code does not
5781 add to the memory footprint of the code ;-) Small is beautiful!
5782 When adding new features, these should compile conditionally only
5783 (using #ifdef), and the resulting code with the new feature
5784 disabled must not need more memory than the old code without your
5787 * Remember that there is a size limit of 100 kB per message on the
5788 u-boot mailing list. Bigger patches will be moderated. If they are
5789 reasonable and not too big, they will be acknowledged. But patches
5790 bigger than the size limit should be avoided.
projects / karo-tx-uboot.git / blob