2 # (C) Copyright 2000 - 2013
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # SPDX-License-Identifier: GPL-2.0+
11 This directory contains the source code for U-Boot, a boot loader for
12 Embedded boards based on PowerPC, ARM, MIPS and several other
13 processors, which can be installed in a boot ROM and used to
14 initialize and test the hardware or to download and run application
17 The development of U-Boot is closely related to Linux: some parts of
18 the source code originate in the Linux source tree, we have some
19 header files in common, and special provision has been made to
20 support booting of Linux images.
22 Some attention has been paid to make this software easily
23 configurable and extendable. For instance, all monitor commands are
24 implemented with the same call interface, so that it's very easy to
25 add new commands. Also, instead of permanently adding rarely used
26 code (for instance hardware test utilities) to the monitor, you can
27 load and run it dynamically.
33 In general, all boards for which a configuration option exists in the
34 Makefile have been tested to some extent and can be considered
35 "working". In fact, many of them are used in production systems.
37 In case of problems see the CHANGELOG and CREDITS files to find out
38 who contributed the specific port. The boards.cfg file lists board
41 Note: There is no CHANGELOG file in the actual U-Boot source tree;
42 it can be created dynamically from the Git log using:
50 In case you have questions about, problems with or contributions for
51 U-Boot you should send a message to the U-Boot mailing list at
52 <u-boot@lists.denx.de>. There is also an archive of previous traffic
53 on the mailing list - please search the archive before asking FAQ's.
54 Please see http://lists.denx.de/pipermail/u-boot and
55 http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
58 Where to get source code:
59 =========================
61 The U-Boot source code is maintained in the git repository at
62 git://www.denx.de/git/u-boot.git ; you can browse it online at
63 http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
65 The "snapshot" links on this page allow you to download tarballs of
66 any version you might be interested in. Official releases are also
67 available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
70 Pre-built (and tested) images are available from
71 ftp://ftp.denx.de/pub/u-boot/images/
77 - start from 8xxrom sources
78 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
80 - make it easier to add custom boards
81 - make it possible to add other [PowerPC] CPUs
82 - extend functions, especially:
83 * Provide extended interface to Linux boot loader
86 * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
87 - create ARMBoot project (http://sourceforge.net/projects/armboot)
88 - add other CPU families (starting with ARM)
89 - create U-Boot project (http://sourceforge.net/projects/u-boot)
90 - current project page: see http://www.denx.de/wiki/U-Boot
96 The "official" name of this project is "Das U-Boot". The spelling
97 "U-Boot" shall be used in all written text (documentation, comments
98 in source files etc.). Example:
100 This is the README file for the U-Boot project.
102 File names etc. shall be based on the string "u-boot". Examples:
104 include/asm-ppc/u-boot.h
106 #include <asm/u-boot.h>
108 Variable names, preprocessor constants etc. shall be either based on
109 the string "u_boot" or on "U_BOOT". Example:
111 U_BOOT_VERSION u_boot_logo
112 IH_OS_U_BOOT u_boot_hush_start
118 Starting with the release in October 2008, the names of the releases
119 were changed from numerical release numbers without deeper meaning
120 into a time stamp based numbering. Regular releases are identified by
121 names consisting of the calendar year and month of the release date.
122 Additional fields (if present) indicate release candidates or bug fix
123 releases in "stable" maintenance trees.
126 U-Boot v2009.11 - Release November 2009
127 U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
128 U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
134 /arch Architecture specific files
135 /arm Files generic to ARM architecture
136 /cpu CPU specific files
137 /arm720t Files specific to ARM 720 CPUs
138 /arm920t Files specific to ARM 920 CPUs
139 /at91 Files specific to Atmel AT91RM9200 CPU
140 /imx Files specific to Freescale MC9328 i.MX CPUs
141 /s3c24x0 Files specific to Samsung S3C24X0 CPUs
142 /arm926ejs Files specific to ARM 926 CPUs
143 /arm1136 Files specific to ARM 1136 CPUs
144 /ixp Files specific to Intel XScale IXP CPUs
145 /pxa Files specific to Intel XScale PXA CPUs
146 /sa1100 Files specific to Intel StrongARM SA1100 CPUs
147 /lib Architecture specific library files
148 /avr32 Files generic to AVR32 architecture
149 /cpu CPU specific files
150 /lib Architecture specific library files
151 /blackfin Files generic to Analog Devices Blackfin architecture
152 /cpu CPU specific files
153 /lib Architecture specific library files
154 /m68k Files generic to m68k architecture
155 /cpu CPU specific files
156 /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
157 /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
158 /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
159 /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
160 /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
161 /lib Architecture specific library files
162 /microblaze Files generic to microblaze architecture
163 /cpu CPU specific files
164 /lib Architecture specific library files
165 /mips Files generic to MIPS architecture
166 /cpu CPU specific files
167 /mips32 Files specific to MIPS32 CPUs
168 /xburst Files specific to Ingenic XBurst CPUs
169 /lib Architecture specific library files
170 /nds32 Files generic to NDS32 architecture
171 /cpu CPU specific files
172 /n1213 Files specific to Andes Technology N1213 CPUs
173 /lib Architecture specific library files
174 /nios2 Files generic to Altera NIOS2 architecture
175 /cpu CPU specific files
176 /lib Architecture specific library files
177 /openrisc Files generic to OpenRISC architecture
178 /cpu CPU specific files
179 /lib Architecture specific library files
180 /powerpc Files generic to PowerPC architecture
181 /cpu CPU specific files
182 /74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
183 /mpc5xx Files specific to Freescale MPC5xx CPUs
184 /mpc5xxx Files specific to Freescale MPC5xxx CPUs
185 /mpc8xx Files specific to Freescale MPC8xx CPUs
186 /mpc824x Files specific to Freescale MPC824x CPUs
187 /mpc8260 Files specific to Freescale MPC8260 CPUs
188 /mpc85xx Files specific to Freescale MPC85xx CPUs
189 /ppc4xx Files specific to AMCC PowerPC 4xx CPUs
190 /lib Architecture specific library files
191 /sh Files generic to SH architecture
192 /cpu CPU specific files
193 /sh2 Files specific to sh2 CPUs
194 /sh3 Files specific to sh3 CPUs
195 /sh4 Files specific to sh4 CPUs
196 /lib Architecture specific library files
197 /sparc Files generic to SPARC architecture
198 /cpu CPU specific files
199 /leon2 Files specific to Gaisler LEON2 SPARC CPU
200 /leon3 Files specific to Gaisler LEON3 SPARC CPU
201 /lib Architecture specific library files
202 /x86 Files generic to x86 architecture
203 /cpu CPU specific files
204 /lib Architecture specific library files
205 /api Machine/arch independent API for external apps
206 /board Board dependent files
207 /common Misc architecture independent functions
208 /disk Code for disk drive partition handling
209 /doc Documentation (don't expect too much)
210 /drivers Commonly used device drivers
211 /dts Contains Makefile for building internal U-Boot fdt.
212 /examples Example code for standalone applications, etc.
213 /fs Filesystem code (cramfs, ext2, jffs2, etc.)
214 /include Header Files
215 /lib Files generic to all architectures
216 /libfdt Library files to support flattened device trees
217 /lzma Library files to support LZMA decompression
218 /lzo Library files to support LZO decompression
220 /post Power On Self Test
221 /spl Secondary Program Loader framework
222 /tools Tools to build S-Record or U-Boot images, etc.
224 Software Configuration:
225 =======================
227 Configuration is usually done using C preprocessor defines; the
228 rationale behind that is to avoid dead code whenever possible.
230 There are two classes of configuration variables:
232 * Configuration _OPTIONS_:
233 These are selectable by the user and have names beginning with
236 * Configuration _SETTINGS_:
237 These depend on the hardware etc. and should not be meddled with if
238 you don't know what you're doing; they have names beginning with
241 Later we will add a configuration tool - probably similar to or even
242 identical to what's used for the Linux kernel. Right now, we have to
243 do the configuration by hand, which means creating some symbolic
244 links and editing some configuration files. We use the TQM8xxL boards
248 Selection of Processor Architecture and Board Type:
249 ---------------------------------------------------
251 For all supported boards there are ready-to-use default
252 configurations available; just type "make <board_name>_config".
254 Example: For a TQM823L module type:
259 For the Cogent platform, you need to specify the CPU type as well;
260 e.g. "make cogent_mpc8xx_config". And also configure the cogent
261 directory according to the instructions in cogent/README.
264 Configuration Options:
265 ----------------------
267 Configuration depends on the combination of board and CPU type; all
268 such information is kept in a configuration file
269 "include/configs/<board_name>.h".
271 Example: For a TQM823L module, all configuration settings are in
272 "include/configs/TQM823L.h".
275 Many of the options are named exactly as the corresponding Linux
276 kernel configuration options. The intention is to make it easier to
277 build a config tool - later.
280 The following options need to be configured:
282 - CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
284 - Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
286 - CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
287 Define exactly one, e.g. CONFIG_ATSTK1002
289 - CPU Module Type: (if CONFIG_COGENT is defined)
290 Define exactly one of
292 --- FIXME --- not tested yet:
293 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
294 CONFIG_CMA287_23, CONFIG_CMA287_50
296 - Motherboard Type: (if CONFIG_COGENT is defined)
297 Define exactly one of
298 CONFIG_CMA101, CONFIG_CMA102
300 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
301 Define one or more of
304 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
305 Define one or more of
306 CONFIG_LCD_HEARTBEAT - update a character position on
307 the LCD display every second with
310 - Board flavour: (if CONFIG_MPC8260ADS is defined)
313 CONFIG_SYS_8260ADS - original MPC8260ADS
314 CONFIG_SYS_8266ADS - MPC8266ADS
315 CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
316 CONFIG_SYS_8272ADS - MPC8272ADS
318 - Marvell Family Member
319 CONFIG_SYS_MVFS - define it if you want to enable
320 multiple fs option at one time
321 for marvell soc family
323 - MPC824X Family Member (if CONFIG_MPC824X is defined)
324 Define exactly one of
325 CONFIG_MPC8240, CONFIG_MPC8245
327 - 8xx CPU Options: (if using an MPC8xx CPU)
328 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
329 get_gclk_freq() cannot work
330 e.g. if there is no 32KHz
331 reference PIT/RTC clock
332 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
335 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
336 CONFIG_SYS_8xx_CPUCLK_MIN
337 CONFIG_SYS_8xx_CPUCLK_MAX
338 CONFIG_8xx_CPUCLK_DEFAULT
339 See doc/README.MPC866
341 CONFIG_SYS_MEASURE_CPUCLK
343 Define this to measure the actual CPU clock instead
344 of relying on the correctness of the configured
345 values. Mostly useful for board bringup to make sure
346 the PLL is locked at the intended frequency. Note
347 that this requires a (stable) reference clock (32 kHz
348 RTC clock or CONFIG_SYS_8XX_XIN)
350 CONFIG_SYS_DELAYED_ICACHE
352 Define this option if you want to enable the
353 ICache only when Code runs from RAM.
358 Specifies that the core is a 64-bit PowerPC implementation (implements
359 the "64" category of the Power ISA). This is necessary for ePAPR
360 compliance, among other possible reasons.
362 CONFIG_SYS_FSL_TBCLK_DIV
364 Defines the core time base clock divider ratio compared to the
365 system clock. On most PQ3 devices this is 8, on newer QorIQ
366 devices it can be 16 or 32. The ratio varies from SoC to Soc.
368 CONFIG_SYS_FSL_PCIE_COMPAT
370 Defines the string to utilize when trying to match PCIe device
371 tree nodes for the given platform.
373 CONFIG_SYS_PPC_E500_DEBUG_TLB
375 Enables a temporary TLB entry to be used during boot to work
376 around limitations in e500v1 and e500v2 external debugger
377 support. This reduces the portions of the boot code where
378 breakpoints and single stepping do not work. The value of this
379 symbol should be set to the TLB1 entry to be used for this
382 CONFIG_SYS_FSL_ERRATUM_A004510
384 Enables a workaround for erratum A004510. If set,
385 then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
386 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.
388 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
389 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)
391 Defines one or two SoC revisions (low 8 bits of SVR)
392 for which the A004510 workaround should be applied.
394 The rest of SVR is either not relevant to the decision
395 of whether the erratum is present (e.g. p2040 versus
396 p2041) or is implied by the build target, which controls
397 whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.
399 See Freescale App Note 4493 for more information about
402 CONFIG_A003399_NOR_WORKAROUND
403 Enables a workaround for IFC erratum A003399. It is only
404 requred during NOR boot.
406 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
408 This is the value to write into CCSR offset 0x18600
409 according to the A004510 workaround.
411 CONFIG_SYS_FSL_DSP_DDR_ADDR
412 This value denotes start offset of DDR memory which is
413 connected exclusively to the DSP cores.
415 CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
416 This value denotes start offset of M2 memory
417 which is directly connected to the DSP core.
419 CONFIG_SYS_FSL_DSP_M3_RAM_ADDR
420 This value denotes start offset of M3 memory which is directly
421 connected to the DSP core.
423 CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
424 This value denotes start offset of DSP CCSR space.
426 CONFIG_SYS_FSL_DDR_EMU
427 Specify emulator support for DDR. Some DDR features such as
428 deskew training are not available.
430 - Generic CPU options:
431 CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
433 Defines the endianess of the CPU. Implementation of those
434 values is arch specific.
436 - Intel Monahans options:
437 CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
439 Defines the Monahans run mode to oscillator
440 ratio. Valid values are 8, 16, 24, 31. The core
441 frequency is this value multiplied by 13 MHz.
443 CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
445 Defines the Monahans turbo mode to oscillator
446 ratio. Valid values are 1 (default if undefined) and
447 2. The core frequency as calculated above is multiplied
451 CONFIG_SYS_INIT_SP_OFFSET
453 Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
454 pointer. This is needed for the temporary stack before
457 CONFIG_SYS_MIPS_CACHE_MODE
459 Cache operation mode for the MIPS CPU.
460 See also arch/mips/include/asm/mipsregs.h.
462 CONF_CM_CACHABLE_NO_WA
465 CONF_CM_CACHABLE_NONCOHERENT
469 CONF_CM_CACHABLE_ACCELERATED
471 CONFIG_SYS_XWAY_EBU_BOOTCFG
473 Special option for Lantiq XWAY SoCs for booting from NOR flash.
474 See also arch/mips/cpu/mips32/start.S.
476 CONFIG_XWAY_SWAP_BYTES
478 Enable compilation of tools/xway-swap-bytes needed for Lantiq
479 XWAY SoCs for booting from NOR flash. The U-Boot image needs to
480 be swapped if a flash programmer is used.
483 CONFIG_SYS_EXCEPTION_VECTORS_HIGH
485 Select high exception vectors of the ARM core, e.g., do not
486 clear the V bit of the c1 register of CP15.
488 CONFIG_SYS_THUMB_BUILD
490 Use this flag to build U-Boot using the Thumb instruction
491 set for ARM architectures. Thumb instruction set provides
492 better code density. For ARM architectures that support
493 Thumb2 this flag will result in Thumb2 code generated by
496 CONFIG_ARM_ERRATA_716044
497 CONFIG_ARM_ERRATA_742230
498 CONFIG_ARM_ERRATA_743622
499 CONFIG_ARM_ERRATA_751472
501 If set, the workarounds for these ARM errata are applied early
502 during U-Boot startup. Note that these options force the
503 workarounds to be applied; no CPU-type/version detection
504 exists, unlike the similar options in the Linux kernel. Do not
505 set these options unless they apply!
510 The frequency of the timer returned by get_timer().
511 get_timer() must operate in milliseconds and this CONFIG
512 option must be set to 1000.
514 - Linux Kernel Interface:
517 U-Boot stores all clock information in Hz
518 internally. For binary compatibility with older Linux
519 kernels (which expect the clocks passed in the
520 bd_info data to be in MHz) the environment variable
521 "clocks_in_mhz" can be defined so that U-Boot
522 converts clock data to MHZ before passing it to the
524 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
525 "clocks_in_mhz=1" is automatically included in the
528 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
530 When transferring memsize parameter to linux, some versions
531 expect it to be in bytes, others in MB.
532 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
536 New kernel versions are expecting firmware settings to be
537 passed using flattened device trees (based on open firmware
541 * New libfdt-based support
542 * Adds the "fdt" command
543 * The bootm command automatically updates the fdt
545 OF_CPU - The proper name of the cpus node (only required for
546 MPC512X and MPC5xxx based boards).
547 OF_SOC - The proper name of the soc node (only required for
548 MPC512X and MPC5xxx based boards).
549 OF_TBCLK - The timebase frequency.
550 OF_STDOUT_PATH - The path to the console device
552 boards with QUICC Engines require OF_QE to set UCC MAC
555 CONFIG_OF_BOARD_SETUP
557 Board code has addition modification that it wants to make
558 to the flat device tree before handing it off to the kernel
562 This define fills in the correct boot CPU in the boot
563 param header, the default value is zero if undefined.
567 U-Boot can detect if an IDE device is present or not.
568 If not, and this new config option is activated, U-Boot
569 removes the ATA node from the DTS before booting Linux,
570 so the Linux IDE driver does not probe the device and
571 crash. This is needed for buggy hardware (uc101) where
572 no pull down resistor is connected to the signal IDE5V_DD7.
574 CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
576 This setting is mandatory for all boards that have only one
577 machine type and must be used to specify the machine type
578 number as it appears in the ARM machine registry
579 (see http://www.arm.linux.org.uk/developer/machines/).
580 Only boards that have multiple machine types supported
581 in a single configuration file and the machine type is
582 runtime discoverable, do not have to use this setting.
584 - vxWorks boot parameters:
586 bootvx constructs a valid bootline using the following
587 environments variables: bootfile, ipaddr, serverip, hostname.
588 It loads the vxWorks image pointed bootfile.
590 CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
591 CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
592 CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
593 CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
595 CONFIG_SYS_VXWORKS_ADD_PARAMS
597 Add it at the end of the bootline. E.g "u=username pw=secret"
599 Note: If a "bootargs" environment is defined, it will overwride
600 the defaults discussed just above.
602 - Cache Configuration:
603 CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
604 CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
605 CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
607 - Cache Configuration for ARM:
608 CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
610 CONFIG_SYS_PL310_BASE - Physical base address of PL310
611 controller register space
616 Define this if you want support for Amba PrimeCell PL010 UARTs.
620 Define this if you want support for Amba PrimeCell PL011 UARTs.
624 If you have Amba PrimeCell PL011 UARTs, set this variable to
625 the clock speed of the UARTs.
629 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
630 define this to a list of base addresses for each (supported)
631 port. See e.g. include/configs/versatile.h
633 CONFIG_PL011_SERIAL_RLCR
635 Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
636 have separate receive and transmit line control registers. Set
637 this variable to initialize the extra register.
639 CONFIG_PL011_SERIAL_FLUSH_ON_INIT
641 On some platforms (e.g. U8500) U-Boot is loaded by a second stage
642 boot loader that has already initialized the UART. Define this
643 variable to flush the UART at init time.
647 Depending on board, define exactly one serial port
648 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
649 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
650 console by defining CONFIG_8xx_CONS_NONE
652 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
653 port routines must be defined elsewhere
654 (i.e. serial_init(), serial_getc(), ...)
657 Enables console device for a color framebuffer. Needs following
658 defines (cf. smiLynxEM, i8042)
659 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
661 VIDEO_HW_RECTFILL graphic chip supports
664 VIDEO_HW_BITBLT graphic chip supports
665 bit-blit (cf. smiLynxEM)
666 VIDEO_VISIBLE_COLS visible pixel columns
668 VIDEO_VISIBLE_ROWS visible pixel rows
669 VIDEO_PIXEL_SIZE bytes per pixel
670 VIDEO_DATA_FORMAT graphic data format
671 (0-5, cf. cfb_console.c)
672 VIDEO_FB_ADRS framebuffer address
673 VIDEO_KBD_INIT_FCT keyboard int fct
674 (i.e. i8042_kbd_init())
675 VIDEO_TSTC_FCT test char fct
677 VIDEO_GETC_FCT get char fct
679 CONFIG_CONSOLE_CURSOR cursor drawing on/off
680 (requires blink timer
682 CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
683 CONFIG_CONSOLE_TIME display time/date info in
685 (requires CONFIG_CMD_DATE)
686 CONFIG_VIDEO_LOGO display Linux logo in
688 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
689 linux_logo.h for logo.
690 Requires CONFIG_VIDEO_LOGO
691 CONFIG_CONSOLE_EXTRA_INFO
692 additional board info beside
695 When CONFIG_CFB_CONSOLE_ANSI is defined, console will support
696 a limited number of ANSI escape sequences (cursor control,
697 erase functions and limited graphics rendition control).
699 When CONFIG_CFB_CONSOLE is defined, video console is
700 default i/o. Serial console can be forced with
701 environment 'console=serial'.
703 When CONFIG_SILENT_CONSOLE is defined, all console
704 messages (by U-Boot and Linux!) can be silenced with
705 the "silent" environment variable. See
706 doc/README.silent for more information.
708 CONFIG_SYS_CONSOLE_BG_COL: define the backgroundcolor, default
710 CONFIG_SYS_CONSOLE_FG_COL: define the foregroundcolor, default
714 CONFIG_BAUDRATE - in bps
715 Select one of the baudrates listed in
716 CONFIG_SYS_BAUDRATE_TABLE, see below.
717 CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
719 - Console Rx buffer length
720 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
721 the maximum receive buffer length for the SMC.
722 This option is actual only for 82xx and 8xx possible.
723 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
724 must be defined, to setup the maximum idle timeout for
727 - Pre-Console Buffer:
728 Prior to the console being initialised (i.e. serial UART
729 initialised etc) all console output is silently discarded.
730 Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
731 buffer any console messages prior to the console being
732 initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ
733 bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is
734 a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ
735 bytes are output before the console is initialised, the
736 earlier bytes are discarded.
738 'Sane' compilers will generate smaller code if
739 CONFIG_PRE_CON_BUF_SZ is a power of 2
741 - Safe printf() functions
742 Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
743 the printf() functions. These are defined in
744 include/vsprintf.h and include snprintf(), vsnprintf() and
745 so on. Code size increase is approximately 300-500 bytes.
746 If this option is not given then these functions will
747 silently discard their buffer size argument - this means
748 you are not getting any overflow checking in this case.
750 - Boot Delay: CONFIG_BOOTDELAY - in seconds
751 Delay before automatically booting the default image;
752 set to -1 to disable autoboot.
753 set to -2 to autoboot with no delay and not check for abort
754 (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
756 See doc/README.autoboot for these options that
757 work with CONFIG_BOOTDELAY. None are required.
758 CONFIG_BOOT_RETRY_TIME
759 CONFIG_BOOT_RETRY_MIN
760 CONFIG_AUTOBOOT_KEYED
761 CONFIG_AUTOBOOT_PROMPT
762 CONFIG_AUTOBOOT_DELAY_STR
763 CONFIG_AUTOBOOT_STOP_STR
764 CONFIG_AUTOBOOT_DELAY_STR2
765 CONFIG_AUTOBOOT_STOP_STR2
766 CONFIG_ZERO_BOOTDELAY_CHECK
767 CONFIG_RESET_TO_RETRY
771 Only needed when CONFIG_BOOTDELAY is enabled;
772 define a command string that is automatically executed
773 when no character is read on the console interface
774 within "Boot Delay" after reset.
777 This can be used to pass arguments to the bootm
778 command. The value of CONFIG_BOOTARGS goes into the
779 environment value "bootargs".
781 CONFIG_RAMBOOT and CONFIG_NFSBOOT
782 The value of these goes into the environment as
783 "ramboot" and "nfsboot" respectively, and can be used
784 as a convenience, when switching between booting from
790 When this option is #defined, the existence of the
791 environment variable "preboot" will be checked
792 immediately before starting the CONFIG_BOOTDELAY
793 countdown and/or running the auto-boot command resp.
794 entering interactive mode.
796 This feature is especially useful when "preboot" is
797 automatically generated or modified. For an example
798 see the LWMON board specific code: here "preboot" is
799 modified when the user holds down a certain
800 combination of keys on the (special) keyboard when
803 - Serial Download Echo Mode:
805 If defined to 1, all characters received during a
806 serial download (using the "loads" command) are
807 echoed back. This might be needed by some terminal
808 emulations (like "cu"), but may as well just take
809 time on others. This setting #define's the initial
810 value of the "loads_echo" environment variable.
812 - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
814 Select one of the baudrates listed in
815 CONFIG_SYS_BAUDRATE_TABLE, see below.
818 Monitor commands can be included or excluded
819 from the build by using the #include files
820 <config_cmd_all.h> and #undef'ing unwanted
821 commands, or using <config_cmd_default.h>
822 and augmenting with additional #define's
825 The default command configuration includes all commands
826 except those marked below with a "*".
828 CONFIG_CMD_ASKENV * ask for env variable
829 CONFIG_CMD_BDI bdinfo
830 CONFIG_CMD_BEDBUG * Include BedBug Debugger
831 CONFIG_CMD_BMP * BMP support
832 CONFIG_CMD_BSP * Board specific commands
833 CONFIG_CMD_BOOTD bootd
834 CONFIG_CMD_CACHE * icache, dcache
835 CONFIG_CMD_CONSOLE coninfo
836 CONFIG_CMD_CRC32 * crc32
837 CONFIG_CMD_DATE * support for RTC, date/time...
838 CONFIG_CMD_DHCP * DHCP support
839 CONFIG_CMD_DIAG * Diagnostics
840 CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
841 CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
842 CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
843 CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
844 CONFIG_CMD_DTT * Digital Therm and Thermostat
845 CONFIG_CMD_ECHO echo arguments
846 CONFIG_CMD_EDITENV edit env variable
847 CONFIG_CMD_EEPROM * EEPROM read/write support
848 CONFIG_CMD_ELF * bootelf, bootvx
849 CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
850 CONFIG_CMD_ENV_FLAGS * display details about env flags
851 CONFIG_CMD_ENV_EXISTS * check existence of env variable
852 CONFIG_CMD_EXPORTENV * export the environment
853 CONFIG_CMD_EXT2 * ext2 command support
854 CONFIG_CMD_EXT4 * ext4 command support
855 CONFIG_CMD_SAVEENV saveenv
856 CONFIG_CMD_FDC * Floppy Disk Support
857 CONFIG_CMD_FAT * FAT command support
858 CONFIG_CMD_FDOS * Dos diskette Support
859 CONFIG_CMD_FLASH flinfo, erase, protect
860 CONFIG_CMD_FPGA FPGA device initialization support
861 CONFIG_CMD_FUSE * Device fuse support
862 CONFIG_CMD_GETTIME * Get time since boot
863 CONFIG_CMD_GO * the 'go' command (exec code)
864 CONFIG_CMD_GREPENV * search environment
865 CONFIG_CMD_HASH * calculate hash / digest
866 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
867 CONFIG_CMD_I2C * I2C serial bus support
868 CONFIG_CMD_IDE * IDE harddisk support
869 CONFIG_CMD_IMI iminfo
870 CONFIG_CMD_IMLS List all images found in NOR flash
871 CONFIG_CMD_IMLS_NAND * List all images found in NAND flash
872 CONFIG_CMD_IMMAP * IMMR dump support
873 CONFIG_CMD_IMPORTENV * import an environment
874 CONFIG_CMD_INI * import data from an ini file into the env
875 CONFIG_CMD_IRQ * irqinfo
876 CONFIG_CMD_ITEST Integer/string test of 2 values
877 CONFIG_CMD_JFFS2 * JFFS2 Support
878 CONFIG_CMD_KGDB * kgdb
879 CONFIG_CMD_LDRINFO * ldrinfo (display Blackfin loader)
880 CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
882 CONFIG_CMD_LOADB loadb
883 CONFIG_CMD_LOADS loads
884 CONFIG_CMD_MD5SUM * print md5 message digest
885 (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
886 CONFIG_CMD_MEMINFO * Display detailed memory information
887 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
889 CONFIG_CMD_MEMTEST * mtest
890 CONFIG_CMD_MISC Misc functions like sleep etc
891 CONFIG_CMD_MMC * MMC memory mapped support
892 CONFIG_CMD_MII * MII utility commands
893 CONFIG_CMD_MTDPARTS * MTD partition support
894 CONFIG_CMD_NAND * NAND support
895 CONFIG_CMD_NET bootp, tftpboot, rarpboot
896 CONFIG_CMD_NFS NFS support
897 CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
898 CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
899 CONFIG_CMD_PCI * pciinfo
900 CONFIG_CMD_PCMCIA * PCMCIA support
901 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
903 CONFIG_CMD_PORTIO * Port I/O
904 CONFIG_CMD_READ * Read raw data from partition
905 CONFIG_CMD_REGINFO * Register dump
906 CONFIG_CMD_RUN run command in env variable
907 CONFIG_CMD_SANDBOX * sb command to access sandbox features
908 CONFIG_CMD_SAVES * save S record dump
909 CONFIG_CMD_SCSI * SCSI Support
910 CONFIG_CMD_SDRAM * print SDRAM configuration information
911 (requires CONFIG_CMD_I2C)
912 CONFIG_CMD_SETGETDCR Support for DCR Register access
914 CONFIG_CMD_SF * Read/write/erase SPI NOR flash
915 CONFIG_CMD_SHA1SUM * print sha1 memory digest
916 (requires CONFIG_CMD_MEMORY)
917 CONFIG_CMD_SOFTSWITCH * Soft switch setting command for BF60x
918 CONFIG_CMD_SOURCE "source" command Support
919 CONFIG_CMD_SPI * SPI serial bus support
920 CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
921 CONFIG_CMD_TFTPPUT * TFTP put command (upload)
922 CONFIG_CMD_TIME * run command and report execution time (ARM specific)
923 CONFIG_CMD_TIMER * access to the system tick timer
924 CONFIG_CMD_USB * USB support
925 CONFIG_CMD_CDP * Cisco Discover Protocol support
926 CONFIG_CMD_MFSL * Microblaze FSL support
927 CONFIG_CMD_XIMG Load part of Multi Image
930 EXAMPLE: If you want all functions except of network
931 support you can write:
933 #include "config_cmd_all.h"
934 #undef CONFIG_CMD_NET
937 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
939 Note: Don't enable the "icache" and "dcache" commands
940 (configuration option CONFIG_CMD_CACHE) unless you know
941 what you (and your U-Boot users) are doing. Data
942 cache cannot be enabled on systems like the 8xx or
943 8260 (where accesses to the IMMR region must be
944 uncached), and it cannot be disabled on all other
945 systems where we (mis-) use the data cache to hold an
946 initial stack and some data.
949 XXX - this list needs to get updated!
951 - Regular expression support:
953 If this variable is defined, U-Boot is linked against
954 the SLRE (Super Light Regular Expression) library,
955 which adds regex support to some commands, as for
956 example "env grep" and "setexpr".
960 If this variable is defined, U-Boot will use a device tree
961 to configure its devices, instead of relying on statically
962 compiled #defines in the board file. This option is
963 experimental and only available on a few boards. The device
964 tree is available in the global data as gd->fdt_blob.
966 U-Boot needs to get its device tree from somewhere. This can
967 be done using one of the two options below:
970 If this variable is defined, U-Boot will embed a device tree
971 binary in its image. This device tree file should be in the
972 board directory and called <soc>-<board>.dts. The binary file
973 is then picked up in board_init_f() and made available through
974 the global data structure as gd->blob.
977 If this variable is defined, U-Boot will build a device tree
978 binary. It will be called u-boot.dtb. Architecture-specific
979 code will locate it at run-time. Generally this works by:
981 cat u-boot.bin u-boot.dtb >image.bin
983 and in fact, U-Boot does this for you, creating a file called
984 u-boot-dtb.bin which is useful in the common case. You can
985 still use the individual files if you need something more
990 If this variable is defined, it enables watchdog
991 support for the SoC. There must be support in the SoC
992 specific code for a watchdog. For the 8xx and 8260
993 CPUs, the SIU Watchdog feature is enabled in the SYPCR
994 register. When supported for a specific SoC is
995 available, then no further board specific code should
999 When using a watchdog circuitry external to the used
1000 SoC, then define this variable and provide board
1001 specific code for the "hw_watchdog_reset" function.
1004 CONFIG_VERSION_VARIABLE
1005 If this variable is defined, an environment variable
1006 named "ver" is created by U-Boot showing the U-Boot
1007 version as printed by the "version" command.
1008 Any change to this variable will be reverted at the
1013 When CONFIG_CMD_DATE is selected, the type of the RTC
1014 has to be selected, too. Define exactly one of the
1017 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
1018 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
1019 CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
1020 CONFIG_RTC_MC146818 - use MC146818 RTC
1021 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
1022 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
1023 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
1024 CONFIG_RTC_DS164x - use Dallas DS164x RTC
1025 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
1026 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
1027 CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
1028 CONFIG_SYS_RV3029_TCR - enable trickle charger on
1031 Note that if the RTC uses I2C, then the I2C interface
1032 must also be configured. See I2C Support, below.
1035 CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
1037 The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
1038 chip-ngpio pairs that tell the PCA953X driver the number of
1039 pins supported by a particular chip.
1041 Note that if the GPIO device uses I2C, then the I2C interface
1042 must also be configured. See I2C Support, below.
1044 - Timestamp Support:
1046 When CONFIG_TIMESTAMP is selected, the timestamp
1047 (date and time) of an image is printed by image
1048 commands like bootm or iminfo. This option is
1049 automatically enabled when you select CONFIG_CMD_DATE .
1051 - Partition Labels (disklabels) Supported:
1052 Zero or more of the following:
1053 CONFIG_MAC_PARTITION Apple's MacOS partition table.
1054 CONFIG_DOS_PARTITION MS Dos partition table, traditional on the
1055 Intel architecture, USB sticks, etc.
1056 CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc.
1057 CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
1058 bootloader. Note 2TB partition limit; see
1060 CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
1062 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
1063 CONFIG_CMD_SCSI) you must configure support for at
1064 least one non-MTD partition type as well.
1067 CONFIG_IDE_RESET_ROUTINE - this is defined in several
1068 board configurations files but used nowhere!
1070 CONFIG_IDE_RESET - is this is defined, IDE Reset will
1071 be performed by calling the function
1072 ide_set_reset(int reset)
1073 which has to be defined in a board specific file
1078 Set this to enable ATAPI support.
1083 Set this to enable support for disks larger than 137GB
1084 Also look at CONFIG_SYS_64BIT_LBA.
1085 Whithout these , LBA48 support uses 32bit variables and will 'only'
1086 support disks up to 2.1TB.
1088 CONFIG_SYS_64BIT_LBA:
1089 When enabled, makes the IDE subsystem use 64bit sector addresses.
1093 At the moment only there is only support for the
1094 SYM53C8XX SCSI controller; define
1095 CONFIG_SCSI_SYM53C8XX to enable it.
1097 CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
1098 CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
1099 CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
1100 maximum numbers of LUNs, SCSI ID's and target
1102 CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
1104 The environment variable 'scsidevs' is set to the number of
1105 SCSI devices found during the last scan.
1107 - NETWORK Support (PCI):
1109 Support for Intel 8254x/8257x gigabit chips.
1112 Utility code for direct access to the SPI bus on Intel 8257x.
1113 This does not do anything useful unless you set at least one
1114 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
1116 CONFIG_E1000_SPI_GENERIC
1117 Allow generic access to the SPI bus on the Intel 8257x, for
1118 example with the "sspi" command.
1121 Management command for E1000 devices. When used on devices
1122 with SPI support you can reprogram the EEPROM from U-Boot.
1124 CONFIG_E1000_FALLBACK_MAC
1125 default MAC for empty EEPROM after production.
1128 Support for Intel 82557/82559/82559ER chips.
1129 Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
1130 write routine for first time initialisation.
1133 Support for Digital 2114x chips.
1134 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
1135 modem chip initialisation (KS8761/QS6611).
1138 Support for National dp83815 chips.
1141 Support for National dp8382[01] gigabit chips.
1143 - NETWORK Support (other):
1145 CONFIG_DRIVER_AT91EMAC
1146 Support for AT91RM9200 EMAC.
1149 Define this to use reduced MII inteface
1151 CONFIG_DRIVER_AT91EMAC_QUIET
1152 If this defined, the driver is quiet.
1153 The driver doen't show link status messages.
1155 CONFIG_CALXEDA_XGMAC
1156 Support for the Calxeda XGMAC device
1159 Support for SMSC's LAN91C96 chips.
1161 CONFIG_LAN91C96_BASE
1162 Define this to hold the physical address
1163 of the LAN91C96's I/O space
1165 CONFIG_LAN91C96_USE_32_BIT
1166 Define this to enable 32 bit addressing
1169 Support for SMSC's LAN91C111 chip
1171 CONFIG_SMC91111_BASE
1172 Define this to hold the physical address
1173 of the device (I/O space)
1175 CONFIG_SMC_USE_32_BIT
1176 Define this if data bus is 32 bits
1178 CONFIG_SMC_USE_IOFUNCS
1179 Define this to use i/o functions instead of macros
1180 (some hardware wont work with macros)
1182 CONFIG_DRIVER_TI_EMAC
1183 Support for davinci emac
1185 CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
1186 Define this if you have more then 3 PHYs.
1189 Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
1191 CONFIG_FTGMAC100_EGIGA
1192 Define this to use GE link update with gigabit PHY.
1193 Define this if FTGMAC100 is connected to gigabit PHY.
1194 If your system has 10/100 PHY only, it might not occur
1195 wrong behavior. Because PHY usually return timeout or
1196 useless data when polling gigabit status and gigabit
1197 control registers. This behavior won't affect the
1198 correctnessof 10/100 link speed update.
1201 Support for SMSC's LAN911x and LAN921x chips
1204 Define this to hold the physical address
1205 of the device (I/O space)
1207 CONFIG_SMC911X_32_BIT
1208 Define this if data bus is 32 bits
1210 CONFIG_SMC911X_16_BIT
1211 Define this if data bus is 16 bits. If your processor
1212 automatically converts one 32 bit word to two 16 bit
1213 words you may also try CONFIG_SMC911X_32_BIT.
1216 Support for Renesas on-chip Ethernet controller
1218 CONFIG_SH_ETHER_USE_PORT
1219 Define the number of ports to be used
1221 CONFIG_SH_ETHER_PHY_ADDR
1222 Define the ETH PHY's address
1224 CONFIG_SH_ETHER_CACHE_WRITEBACK
1225 If this option is set, the driver enables cache flush.
1229 Support TPM devices.
1232 Support for i2c bus TPM devices. Only one device
1233 per system is supported at this time.
1235 CONFIG_TPM_TIS_I2C_BUS_NUMBER
1236 Define the the i2c bus number for the TPM device
1238 CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS
1239 Define the TPM's address on the i2c bus
1241 CONFIG_TPM_TIS_I2C_BURST_LIMITATION
1242 Define the burst count bytes upper limit
1244 CONFIG_TPM_ATMEL_TWI
1245 Support for Atmel TWI TPM device. Requires I2C support.
1248 Support for generic parallel port TPM devices. Only one device
1249 per system is supported at this time.
1251 CONFIG_TPM_TIS_BASE_ADDRESS
1252 Base address where the generic TPM device is mapped
1253 to. Contemporary x86 systems usually map it at
1257 Add tpm monitor functions.
1258 Requires CONFIG_TPM. If CONFIG_TPM_AUTH_SESSIONS is set, also
1259 provides monitor access to authorized functions.
1262 Define this to enable the TPM support library which provides
1263 functional interfaces to some TPM commands.
1264 Requires support for a TPM device.
1266 CONFIG_TPM_AUTH_SESSIONS
1267 Define this to enable authorized functions in the TPM library.
1268 Requires CONFIG_TPM and CONFIG_SHA1.
1271 At the moment only the UHCI host controller is
1272 supported (PIP405, MIP405, MPC5200); define
1273 CONFIG_USB_UHCI to enable it.
1274 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
1275 and define CONFIG_USB_STORAGE to enable the USB
1278 Supported are USB Keyboards and USB Floppy drives
1280 MPC5200 USB requires additional defines:
1282 for 528 MHz Clock: 0x0001bbbb
1286 for differential drivers: 0x00001000
1287 for single ended drivers: 0x00005000
1288 for differential drivers on PSC3: 0x00000100
1289 for single ended drivers on PSC3: 0x00004100
1290 CONFIG_SYS_USB_EVENT_POLL
1291 May be defined to allow interrupt polling
1292 instead of using asynchronous interrupts
1294 CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
1295 txfilltuning field in the EHCI controller on reset.
1297 CONFIG_USB_HUB_MIN_POWER_ON_DELAY defines the minimum
1298 interval for usb hub power-on delay.(minimum 100msec)
1301 Define the below if you wish to use the USB console.
1302 Once firmware is rebuilt from a serial console issue the
1303 command "setenv stdin usbtty; setenv stdout usbtty" and
1304 attach your USB cable. The Unix command "dmesg" should print
1305 it has found a new device. The environment variable usbtty
1306 can be set to gserial or cdc_acm to enable your device to
1307 appear to a USB host as a Linux gserial device or a
1308 Common Device Class Abstract Control Model serial device.
1309 If you select usbtty = gserial you should be able to enumerate
1311 # modprobe usbserial vendor=0xVendorID product=0xProductID
1312 else if using cdc_acm, simply setting the environment
1313 variable usbtty to be cdc_acm should suffice. The following
1314 might be defined in YourBoardName.h
1317 Define this to build a UDC device
1320 Define this to have a tty type of device available to
1321 talk to the UDC device
1324 Define this to enable the high speed support for usb
1325 device and usbtty. If this feature is enabled, a routine
1326 int is_usbd_high_speed(void)
1327 also needs to be defined by the driver to dynamically poll
1328 whether the enumeration has succeded at high speed or full
1331 CONFIG_SYS_CONSOLE_IS_IN_ENV
1332 Define this if you want stdin, stdout &/or stderr to
1336 CONFIG_SYS_USB_EXTC_CLK 0xBLAH
1337 Derive USB clock from external clock "blah"
1338 - CONFIG_SYS_USB_EXTC_CLK 0x02
1340 CONFIG_SYS_USB_BRG_CLK 0xBLAH
1341 Derive USB clock from brgclk
1342 - CONFIG_SYS_USB_BRG_CLK 0x04
1344 If you have a USB-IF assigned VendorID then you may wish to
1345 define your own vendor specific values either in BoardName.h
1346 or directly in usbd_vendor_info.h. If you don't define
1347 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
1348 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
1349 should pretend to be a Linux device to it's target host.
1351 CONFIG_USBD_MANUFACTURER
1352 Define this string as the name of your company for
1353 - CONFIG_USBD_MANUFACTURER "my company"
1355 CONFIG_USBD_PRODUCT_NAME
1356 Define this string as the name of your product
1357 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
1359 CONFIG_USBD_VENDORID
1360 Define this as your assigned Vendor ID from the USB
1361 Implementors Forum. This *must* be a genuine Vendor ID
1362 to avoid polluting the USB namespace.
1363 - CONFIG_USBD_VENDORID 0xFFFF
1365 CONFIG_USBD_PRODUCTID
1366 Define this as the unique Product ID
1368 - CONFIG_USBD_PRODUCTID 0xFFFF
1370 Some USB device drivers may need to check USB cable attachment.
1371 In this case you can enable following config in BoardName.h:
1372 CONFIG_USB_CABLE_CHECK
1373 This enables function definition:
1374 - usb_cable_connected() in include/usb.h
1375 Implementation of this function is board-specific.
1377 - ULPI Layer Support:
1378 The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
1379 the generic ULPI layer. The generic layer accesses the ULPI PHY
1380 via the platform viewport, so you need both the genric layer and
1381 the viewport enabled. Currently only Chipidea/ARC based
1382 viewport is supported.
1383 To enable the ULPI layer support, define CONFIG_USB_ULPI and
1384 CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
1385 If your ULPI phy needs a different reference clock than the
1386 standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
1387 the appropriate value in Hz.
1390 The MMC controller on the Intel PXA is supported. To
1391 enable this define CONFIG_MMC. The MMC can be
1392 accessed from the boot prompt by mapping the device
1393 to physical memory similar to flash. Command line is
1394 enabled with CONFIG_CMD_MMC. The MMC driver also works with
1395 the FAT fs. This is enabled with CONFIG_CMD_FAT.
1398 Support for Renesas on-chip MMCIF controller
1400 CONFIG_SH_MMCIF_ADDR
1401 Define the base address of MMCIF registers
1404 Define the clock frequency for MMCIF
1406 - USB Device Firmware Update (DFU) class support:
1408 This enables the USB portion of the DFU USB class
1411 This enables the command "dfu" which is used to have
1412 U-Boot create a DFU class device via USB. This command
1413 requires that the "dfu_alt_info" environment variable be
1414 set and define the alt settings to expose to the host.
1417 This enables support for exposing (e)MMC devices via DFU.
1420 This enables support for exposing NAND devices via DFU.
1423 This enables support for exposing RAM via DFU.
1424 Note: DFU spec refer to non-volatile memory usage, but
1425 allow usages beyond the scope of spec - here RAM usage,
1426 one that would help mostly the developer.
1428 CONFIG_SYS_DFU_DATA_BUF_SIZE
1429 Dfu transfer uses a buffer before writing data to the
1430 raw storage device. Make the size (in bytes) of this buffer
1431 configurable. The size of this buffer is also configurable
1432 through the "dfu_bufsiz" environment variable.
1434 CONFIG_SYS_DFU_MAX_FILE_SIZE
1435 When updating files rather than the raw storage device,
1436 we use a static buffer to copy the file into and then write
1437 the buffer once we've been given the whole file. Define
1438 this to the maximum filesize (in bytes) for the buffer.
1439 Default is 4 MiB if undefined.
1441 - Journaling Flash filesystem support:
1442 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
1443 CONFIG_JFFS2_NAND_DEV
1444 Define these for a default partition on a NAND device
1446 CONFIG_SYS_JFFS2_FIRST_SECTOR,
1447 CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
1448 Define these for a default partition on a NOR device
1450 CONFIG_SYS_JFFS_CUSTOM_PART
1451 Define this to create an own partition. You have to provide a
1452 function struct part_info* jffs2_part_info(int part_num)
1454 If you define only one JFFS2 partition you may also want to
1455 #define CONFIG_SYS_JFFS_SINGLE_PART 1
1456 to disable the command chpart. This is the default when you
1457 have not defined a custom partition
1459 - FAT(File Allocation Table) filesystem write function support:
1462 Define this to enable support for saving memory data as a
1463 file in FAT formatted partition.
1465 This will also enable the command "fatwrite" enabling the
1466 user to write files to FAT.
1468 CBFS (Coreboot Filesystem) support
1471 Define this to enable support for reading from a Coreboot
1472 filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
1478 Define this to enable standard (PC-Style) keyboard
1482 Standard PC keyboard driver with US (is default) and
1483 GERMAN key layout (switch via environment 'keymap=de') support.
1484 Export function i8042_kbd_init, i8042_tstc and i8042_getc
1485 for cfb_console. Supports cursor blinking.
1488 Enables a Chrome OS keyboard using the CROS_EC interface.
1489 This uses CROS_EC to communicate with a second microcontroller
1490 which provides key scans on request.
1495 Define this to enable video support (for output to
1498 CONFIG_VIDEO_CT69000
1500 Enable Chips & Technologies 69000 Video chip
1502 CONFIG_VIDEO_SMI_LYNXEM
1503 Enable Silicon Motion SMI 712/710/810 Video chip. The
1504 video output is selected via environment 'videoout'
1505 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
1508 For the CT69000 and SMI_LYNXEM drivers, videomode is
1509 selected via environment 'videomode'. Two different ways
1511 - "videomode=num" 'num' is a standard LiLo mode numbers.
1512 Following standard modes are supported (* is default):
1514 Colors 640x480 800x600 1024x768 1152x864 1280x1024
1515 -------------+---------------------------------------------
1516 8 bits | 0x301* 0x303 0x305 0x161 0x307
1517 15 bits | 0x310 0x313 0x316 0x162 0x319
1518 16 bits | 0x311 0x314 0x317 0x163 0x31A
1519 24 bits | 0x312 0x315 0x318 ? 0x31B
1520 -------------+---------------------------------------------
1521 (i.e. setenv videomode 317; saveenv; reset;)
1523 - "videomode=bootargs" all the video parameters are parsed
1524 from the bootargs. (See drivers/video/videomodes.c)
1527 CONFIG_VIDEO_SED13806
1528 Enable Epson SED13806 driver. This driver supports 8bpp
1529 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
1530 or CONFIG_VIDEO_SED13806_16BPP
1533 Enable the Freescale DIU video driver. Reference boards for
1534 SOCs that have a DIU should define this macro to enable DIU
1535 support, and should also define these other macros:
1541 CONFIG_VIDEO_SW_CURSOR
1542 CONFIG_VGA_AS_SINGLE_DEVICE
1544 CONFIG_VIDEO_BMP_LOGO
1546 The DIU driver will look for the 'video-mode' environment
1547 variable, and if defined, enable the DIU as a console during
1548 boot. See the documentation file README.video for a
1549 description of this variable.
1553 Enable the VGA video / BIOS for x86. The alternative if you
1554 are using coreboot is to use the coreboot frame buffer
1561 Define this to enable a custom keyboard support.
1562 This simply calls drv_keyboard_init() which must be
1563 defined in your board-specific files.
1564 The only board using this so far is RBC823.
1566 - LCD Support: CONFIG_LCD
1568 Define this to enable LCD support (for output to LCD
1569 display); also select one of the supported displays
1570 by defining one of these:
1574 HITACHI TX09D70VM1CCA, 3.5", 240x320.
1576 CONFIG_NEC_NL6448AC33:
1578 NEC NL6448AC33-18. Active, color, single scan.
1580 CONFIG_NEC_NL6448BC20
1582 NEC NL6448BC20-08. 6.5", 640x480.
1583 Active, color, single scan.
1585 CONFIG_NEC_NL6448BC33_54
1587 NEC NL6448BC33-54. 10.4", 640x480.
1588 Active, color, single scan.
1592 Sharp 320x240. Active, color, single scan.
1593 It isn't 16x9, and I am not sure what it is.
1595 CONFIG_SHARP_LQ64D341
1597 Sharp LQ64D341 display, 640x480.
1598 Active, color, single scan.
1602 HLD1045 display, 640x480.
1603 Active, color, single scan.
1607 Optrex CBL50840-2 NF-FW 99 22 M5
1609 Hitachi LMG6912RPFC-00T
1613 320x240. Black & white.
1615 Normally display is black on white background; define
1616 CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
1618 CONFIG_LCD_ALIGNMENT
1620 Normally the LCD is page-aligned (tyically 4KB). If this is
1621 defined then the LCD will be aligned to this value instead.
1622 For ARM it is sometimes useful to use MMU_SECTION_SIZE
1623 here, since it is cheaper to change data cache settings on
1624 a per-section basis.
1626 CONFIG_CONSOLE_SCROLL_LINES
1628 When the console need to be scrolled, this is the number of
1629 lines to scroll by. It defaults to 1. Increasing this makes
1630 the console jump but can help speed up operation when scrolling
1635 Support drawing of RLE8-compressed bitmaps on the LCD.
1639 Enables an 'i2c edid' command which can read EDID
1640 information over I2C from an attached LCD display.
1642 - Splash Screen Support: CONFIG_SPLASH_SCREEN
1644 If this option is set, the environment is checked for
1645 a variable "splashimage". If found, the usual display
1646 of logo, copyright and system information on the LCD
1647 is suppressed and the BMP image at the address
1648 specified in "splashimage" is loaded instead. The
1649 console is redirected to the "nulldev", too. This
1650 allows for a "silent" boot where a splash screen is
1651 loaded very quickly after power-on.
1653 CONFIG_SPLASHIMAGE_GUARD
1655 If this option is set, then U-Boot will prevent the environment
1656 variable "splashimage" from being set to a problematic address
1657 (see README.displaying-bmps and README.arm-unaligned-accesses).
1658 This option is useful for targets where, due to alignment
1659 restrictions, an improperly aligned BMP image will cause a data
1660 abort. If you think you will not have problems with unaligned
1661 accesses (for example because your toolchain prevents them)
1662 there is no need to set this option.
1664 CONFIG_SPLASH_SCREEN_ALIGN
1666 If this option is set the splash image can be freely positioned
1667 on the screen. Environment variable "splashpos" specifies the
1668 position as "x,y". If a positive number is given it is used as
1669 number of pixel from left/top. If a negative number is given it
1670 is used as number of pixel from right/bottom. You can also
1671 specify 'm' for centering the image.
1674 setenv splashpos m,m
1675 => image at center of screen
1677 setenv splashpos 30,20
1678 => image at x = 30 and y = 20
1680 setenv splashpos -10,m
1681 => vertically centered image
1682 at x = dspWidth - bmpWidth - 9
1684 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
1686 If this option is set, additionally to standard BMP
1687 images, gzipped BMP images can be displayed via the
1688 splashscreen support or the bmp command.
1690 - Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
1692 If this option is set, 8-bit RLE compressed BMP images
1693 can be displayed via the splashscreen support or the
1696 - Do compresssing for memory range:
1699 If this option is set, it would use zlib deflate method
1700 to compress the specified memory at its best effort.
1702 - Compression support:
1705 Enabled by default to support gzip compressed images.
1709 If this option is set, support for bzip2 compressed
1710 images is included. If not, only uncompressed and gzip
1711 compressed images are supported.
1713 NOTE: the bzip2 algorithm requires a lot of RAM, so
1714 the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
1719 If this option is set, support for lzma compressed
1722 Note: The LZMA algorithm adds between 2 and 4KB of code and it
1723 requires an amount of dynamic memory that is given by the
1726 (1846 + 768 << (lc + lp)) * sizeof(uint16)
1728 Where lc and lp stand for, respectively, Literal context bits
1729 and Literal pos bits.
1731 This value is upper-bounded by 14MB in the worst case. Anyway,
1732 for a ~4MB large kernel image, we have lc=3 and lp=0 for a
1733 total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
1734 a very small buffer.
1736 Use the lzmainfo tool to determinate the lc and lp values and
1737 then calculate the amount of needed dynamic memory (ensuring
1738 the appropriate CONFIG_SYS_MALLOC_LEN value).
1742 If this option is set, support for LZO compressed images
1748 The address of PHY on MII bus.
1750 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
1752 The clock frequency of the MII bus
1756 If this option is set, support for speed/duplex
1757 detection of gigabit PHY is included.
1759 CONFIG_PHY_RESET_DELAY
1761 Some PHY like Intel LXT971A need extra delay after
1762 reset before any MII register access is possible.
1763 For such PHY, set this option to the usec delay
1764 required. (minimum 300usec for LXT971A)
1766 CONFIG_PHY_CMD_DELAY (ppc4xx)
1768 Some PHY like Intel LXT971A need extra delay after
1769 command issued before MII status register can be read
1779 Define a default value for Ethernet address to use
1780 for the respective Ethernet interface, in case this
1781 is not determined automatically.
1786 Define a default value for the IP address to use for
1787 the default Ethernet interface, in case this is not
1788 determined through e.g. bootp.
1789 (Environment variable "ipaddr")
1791 - Server IP address:
1794 Defines a default value for the IP address of a TFTP
1795 server to contact when using the "tftboot" command.
1796 (Environment variable "serverip")
1798 CONFIG_KEEP_SERVERADDR
1800 Keeps the server's MAC address, in the env 'serveraddr'
1801 for passing to bootargs (like Linux's netconsole option)
1803 - Gateway IP address:
1806 Defines a default value for the IP address of the
1807 default router where packets to other networks are
1809 (Environment variable "gatewayip")
1814 Defines a default value for the subnet mask (or
1815 routing prefix) which is used to determine if an IP
1816 address belongs to the local subnet or needs to be
1817 forwarded through a router.
1818 (Environment variable "netmask")
1820 - Multicast TFTP Mode:
1823 Defines whether you want to support multicast TFTP as per
1824 rfc-2090; for example to work with atftp. Lets lots of targets
1825 tftp down the same boot image concurrently. Note: the Ethernet
1826 driver in use must provide a function: mcast() to join/leave a
1829 - BOOTP Recovery Mode:
1830 CONFIG_BOOTP_RANDOM_DELAY
1832 If you have many targets in a network that try to
1833 boot using BOOTP, you may want to avoid that all
1834 systems send out BOOTP requests at precisely the same
1835 moment (which would happen for instance at recovery
1836 from a power failure, when all systems will try to
1837 boot, thus flooding the BOOTP server. Defining
1838 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1839 inserted before sending out BOOTP requests. The
1840 following delays are inserted then:
1842 1st BOOTP request: delay 0 ... 1 sec
1843 2nd BOOTP request: delay 0 ... 2 sec
1844 3rd BOOTP request: delay 0 ... 4 sec
1846 BOOTP requests: delay 0 ... 8 sec
1848 - DHCP Advanced Options:
1849 You can fine tune the DHCP functionality by defining
1850 CONFIG_BOOTP_* symbols:
1852 CONFIG_BOOTP_SUBNETMASK
1853 CONFIG_BOOTP_GATEWAY
1854 CONFIG_BOOTP_HOSTNAME
1855 CONFIG_BOOTP_NISDOMAIN
1856 CONFIG_BOOTP_BOOTPATH
1857 CONFIG_BOOTP_BOOTFILESIZE
1860 CONFIG_BOOTP_SEND_HOSTNAME
1861 CONFIG_BOOTP_NTPSERVER
1862 CONFIG_BOOTP_TIMEOFFSET
1863 CONFIG_BOOTP_VENDOREX
1864 CONFIG_BOOTP_MAY_FAIL
1866 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
1867 environment variable, not the BOOTP server.
1869 CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found
1870 after the configured retry count, the call will fail
1871 instead of starting over. This can be used to fail over
1872 to Link-local IP address configuration if the DHCP server
1875 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1876 serverip from a DHCP server, it is possible that more
1877 than one DNS serverip is offered to the client.
1878 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1879 serverip will be stored in the additional environment
1880 variable "dnsip2". The first DNS serverip is always
1881 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1884 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1885 to do a dynamic update of a DNS server. To do this, they
1886 need the hostname of the DHCP requester.
1887 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
1888 of the "hostname" environment variable is passed as
1889 option 12 to the DHCP server.
1891 CONFIG_BOOTP_DHCP_REQUEST_DELAY
1893 A 32bit value in microseconds for a delay between
1894 receiving a "DHCP Offer" and sending the "DHCP Request".
1895 This fixes a problem with certain DHCP servers that don't
1896 respond 100% of the time to a "DHCP request". E.g. On an
1897 AT91RM9200 processor running at 180MHz, this delay needed
1898 to be *at least* 15,000 usec before a Windows Server 2003
1899 DHCP server would reply 100% of the time. I recommend at
1900 least 50,000 usec to be safe. The alternative is to hope
1901 that one of the retries will be successful but note that
1902 the DHCP timeout and retry process takes a longer than
1905 - Link-local IP address negotiation:
1906 Negotiate with other link-local clients on the local network
1907 for an address that doesn't require explicit configuration.
1908 This is especially useful if a DHCP server cannot be guaranteed
1909 to exist in all environments that the device must operate.
1911 See doc/README.link-local for more information.
1914 CONFIG_CDP_DEVICE_ID
1916 The device id used in CDP trigger frames.
1918 CONFIG_CDP_DEVICE_ID_PREFIX
1920 A two character string which is prefixed to the MAC address
1925 A printf format string which contains the ascii name of
1926 the port. Normally is set to "eth%d" which sets
1927 eth0 for the first Ethernet, eth1 for the second etc.
1929 CONFIG_CDP_CAPABILITIES
1931 A 32bit integer which indicates the device capabilities;
1932 0x00000010 for a normal host which does not forwards.
1936 An ascii string containing the version of the software.
1940 An ascii string containing the name of the platform.
1944 A 32bit integer sent on the trigger.
1946 CONFIG_CDP_POWER_CONSUMPTION
1948 A 16bit integer containing the power consumption of the
1949 device in .1 of milliwatts.
1951 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1953 A byte containing the id of the VLAN.
1955 - Status LED: CONFIG_STATUS_LED
1957 Several configurations allow to display the current
1958 status using a LED. For instance, the LED will blink
1959 fast while running U-Boot code, stop blinking as
1960 soon as a reply to a BOOTP request was received, and
1961 start blinking slow once the Linux kernel is running
1962 (supported by a status LED driver in the Linux
1963 kernel). Defining CONFIG_STATUS_LED enables this
1969 The status LED can be connected to a GPIO pin.
1970 In such cases, the gpio_led driver can be used as a
1971 status LED backend implementation. Define CONFIG_GPIO_LED
1972 to include the gpio_led driver in the U-Boot binary.
1974 - CAN Support: CONFIG_CAN_DRIVER
1976 Defining CONFIG_CAN_DRIVER enables CAN driver support
1977 on those systems that support this (optional)
1978 feature, like the TQM8xxL modules.
1980 - I2C Support: CONFIG_SYS_I2C
1982 This enable the NEW i2c subsystem, and will allow you to use
1983 i2c commands at the u-boot command line (as long as you set
1984 CONFIG_CMD_I2C in CONFIG_COMMANDS) and communicate with i2c
1985 based realtime clock chips or other i2c devices. See
1986 common/cmd_i2c.c for a description of the command line
1989 ported i2c driver to the new framework:
1990 - drivers/i2c/soft_i2c.c:
1991 - activate first bus with CONFIG_SYS_I2C_SOFT define
1992 CONFIG_SYS_I2C_SOFT_SPEED and CONFIG_SYS_I2C_SOFT_SLAVE
1993 for defining speed and slave address
1994 - activate second bus with I2C_SOFT_DECLARATIONS2 define
1995 CONFIG_SYS_I2C_SOFT_SPEED_2 and CONFIG_SYS_I2C_SOFT_SLAVE_2
1996 for defining speed and slave address
1997 - activate third bus with I2C_SOFT_DECLARATIONS3 define
1998 CONFIG_SYS_I2C_SOFT_SPEED_3 and CONFIG_SYS_I2C_SOFT_SLAVE_3
1999 for defining speed and slave address
2000 - activate fourth bus with I2C_SOFT_DECLARATIONS4 define
2001 CONFIG_SYS_I2C_SOFT_SPEED_4 and CONFIG_SYS_I2C_SOFT_SLAVE_4
2002 for defining speed and slave address
2004 - drivers/i2c/fsl_i2c.c:
2005 - activate i2c driver with CONFIG_SYS_I2C_FSL
2006 define CONFIG_SYS_FSL_I2C_OFFSET for setting the register
2007 offset CONFIG_SYS_FSL_I2C_SPEED for the i2c speed and
2008 CONFIG_SYS_FSL_I2C_SLAVE for the slave addr of the first
2010 - If your board supports a second fsl i2c bus, define
2011 CONFIG_SYS_FSL_I2C2_OFFSET for the register offset
2012 CONFIG_SYS_FSL_I2C2_SPEED for the speed and
2013 CONFIG_SYS_FSL_I2C2_SLAVE for the slave address of the
2016 - drivers/i2c/tegra_i2c.c:
2017 - activate this driver with CONFIG_SYS_I2C_TEGRA
2018 - This driver adds 4 i2c buses with a fix speed from
2019 100000 and the slave addr 0!
2021 - drivers/i2c/ppc4xx_i2c.c
2022 - activate this driver with CONFIG_SYS_I2C_PPC4XX
2023 - CONFIG_SYS_I2C_PPC4XX_CH0 activate hardware channel 0
2024 - CONFIG_SYS_I2C_PPC4XX_CH1 activate hardware channel 1
2026 - drivers/i2c/i2c_mxc.c
2027 - activate this driver with CONFIG_SYS_I2C_MXC
2028 - define speed for bus 1 with CONFIG_SYS_MXC_I2C1_SPEED
2029 - define slave for bus 1 with CONFIG_SYS_MXC_I2C1_SLAVE
2030 - define speed for bus 2 with CONFIG_SYS_MXC_I2C2_SPEED
2031 - define slave for bus 2 with CONFIG_SYS_MXC_I2C2_SLAVE
2032 - define speed for bus 3 with CONFIG_SYS_MXC_I2C3_SPEED
2033 - define slave for bus 3 with CONFIG_SYS_MXC_I2C3_SLAVE
2034 If thoses defines are not set, default value is 100000
2035 for speed, and 0 for slave.
2037 - drivers/i2c/rcar_i2c.c:
2038 - activate this driver with CONFIG_SYS_I2C_RCAR
2039 - This driver adds 4 i2c buses
2041 - CONFIG_SYS_RCAR_I2C0_BASE for setting the register channel 0
2042 - CONFIG_SYS_RCAR_I2C0_SPEED for for the speed channel 0
2043 - CONFIG_SYS_RCAR_I2C1_BASE for setting the register channel 1
2044 - CONFIG_SYS_RCAR_I2C1_SPEED for for the speed channel 1
2045 - CONFIG_SYS_RCAR_I2C2_BASE for setting the register channel 2
2046 - CONFIG_SYS_RCAR_I2C2_SPEED for for the speed channel 2
2047 - CONFIG_SYS_RCAR_I2C3_BASE for setting the register channel 3
2048 - CONFIG_SYS_RCAR_I2C3_SPEED for for the speed channel 3
2049 - CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS for number of i2c buses
2051 - drivers/i2c/sh_i2c.c:
2052 - activate this driver with CONFIG_SYS_I2C_SH
2053 - This driver adds from 2 to 5 i2c buses
2055 - CONFIG_SYS_I2C_SH_BASE0 for setting the register channel 0
2056 - CONFIG_SYS_I2C_SH_SPEED0 for for the speed channel 0
2057 - CONFIG_SYS_I2C_SH_BASE1 for setting the register channel 1
2058 - CONFIG_SYS_I2C_SH_SPEED1 for for the speed channel 1
2059 - CONFIG_SYS_I2C_SH_BASE2 for setting the register channel 2
2060 - CONFIG_SYS_I2C_SH_SPEED2 for for the speed channel 2
2061 - CONFIG_SYS_I2C_SH_BASE3 for setting the register channel 3
2062 - CONFIG_SYS_I2C_SH_SPEED3 for for the speed channel 3
2063 - CONFIG_SYS_I2C_SH_BASE4 for setting the register channel 4
2064 - CONFIG_SYS_I2C_SH_SPEED4 for for the speed channel 4
2065 - CONFIG_SYS_I2C_SH_BASE5 for setting the register channel 5
2066 - CONFIG_SYS_I2C_SH_SPEED5 for for the speed channel 5
2067 - CONFIF_SYS_I2C_SH_NUM_CONTROLLERS for nummber of i2c buses
2069 - drivers/i2c/omap24xx_i2c.c
2070 - activate this driver with CONFIG_SYS_I2C_OMAP24XX
2071 - CONFIG_SYS_OMAP24_I2C_SPEED speed channel 0
2072 - CONFIG_SYS_OMAP24_I2C_SLAVE slave addr channel 0
2073 - CONFIG_SYS_OMAP24_I2C_SPEED1 speed channel 1
2074 - CONFIG_SYS_OMAP24_I2C_SLAVE1 slave addr channel 1
2075 - CONFIG_SYS_OMAP24_I2C_SPEED2 speed channel 2
2076 - CONFIG_SYS_OMAP24_I2C_SLAVE2 slave addr channel 2
2077 - CONFIG_SYS_OMAP24_I2C_SPEED3 speed channel 3
2078 - CONFIG_SYS_OMAP24_I2C_SLAVE3 slave addr channel 3
2079 - CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4
2080 - CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4
2082 - drivers/i2c/zynq_i2c.c
2083 - activate this driver with CONFIG_SYS_I2C_ZYNQ
2084 - set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting
2085 - set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr
2089 CONFIG_SYS_NUM_I2C_BUSES
2090 Hold the number of i2c busses you want to use. If you
2091 don't use/have i2c muxes on your i2c bus, this
2092 is equal to CONFIG_SYS_NUM_I2C_ADAPTERS, and you can
2095 CONFIG_SYS_I2C_DIRECT_BUS
2096 define this, if you don't use i2c muxes on your hardware.
2097 if CONFIG_SYS_I2C_MAX_HOPS is not defined or == 0 you can
2100 CONFIG_SYS_I2C_MAX_HOPS
2101 define how many muxes are maximal consecutively connected
2102 on one i2c bus. If you not use i2c muxes, omit this
2105 CONFIG_SYS_I2C_BUSES
2106 hold a list of busses you want to use, only used if
2107 CONFIG_SYS_I2C_DIRECT_BUS is not defined, for example
2108 a board with CONFIG_SYS_I2C_MAX_HOPS = 1 and
2109 CONFIG_SYS_NUM_I2C_BUSES = 9:
2111 CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP}}, \
2112 {0, {{I2C_MUX_PCA9547, 0x70, 1}}}, \
2113 {0, {{I2C_MUX_PCA9547, 0x70, 2}}}, \
2114 {0, {{I2C_MUX_PCA9547, 0x70, 3}}}, \
2115 {0, {{I2C_MUX_PCA9547, 0x70, 4}}}, \
2116 {0, {{I2C_MUX_PCA9547, 0x70, 5}}}, \
2117 {1, {I2C_NULL_HOP}}, \
2118 {1, {{I2C_MUX_PCA9544, 0x72, 1}}}, \
2119 {1, {{I2C_MUX_PCA9544, 0x72, 2}}}, \
2123 bus 0 on adapter 0 without a mux
2124 bus 1 on adapter 0 with a PCA9547 on address 0x70 port 1
2125 bus 2 on adapter 0 with a PCA9547 on address 0x70 port 2
2126 bus 3 on adapter 0 with a PCA9547 on address 0x70 port 3
2127 bus 4 on adapter 0 with a PCA9547 on address 0x70 port 4
2128 bus 5 on adapter 0 with a PCA9547 on address 0x70 port 5
2129 bus 6 on adapter 1 without a mux
2130 bus 7 on adapter 1 with a PCA9544 on address 0x72 port 1
2131 bus 8 on adapter 1 with a PCA9544 on address 0x72 port 2
2133 If you do not have i2c muxes on your board, omit this define.
2135 - Legacy I2C Support: CONFIG_HARD_I2C
2137 NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
2138 provides the following compelling advantages:
2140 - more than one i2c adapter is usable
2141 - approved multibus support
2142 - better i2c mux support
2144 ** Please consider updating your I2C driver now. **
2146 These enable legacy I2C serial bus commands. Defining
2147 CONFIG_HARD_I2C will include the appropriate I2C driver
2148 for the selected CPU.
2150 This will allow you to use i2c commands at the u-boot
2151 command line (as long as you set CONFIG_CMD_I2C in
2152 CONFIG_COMMANDS) and communicate with i2c based realtime
2153 clock chips. See common/cmd_i2c.c for a description of the
2154 command line interface.
2156 CONFIG_HARD_I2C selects a hardware I2C controller.
2158 There are several other quantities that must also be
2159 defined when you define CONFIG_HARD_I2C.
2161 In both cases you will need to define CONFIG_SYS_I2C_SPEED
2162 to be the frequency (in Hz) at which you wish your i2c bus
2163 to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
2164 the CPU's i2c node address).
2166 Now, the u-boot i2c code for the mpc8xx
2167 (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
2168 and so its address should therefore be cleared to 0 (See,
2169 eg, MPC823e User's Manual p.16-473). So, set
2170 CONFIG_SYS_I2C_SLAVE to 0.
2172 CONFIG_SYS_I2C_INIT_MPC5XXX
2174 When a board is reset during an i2c bus transfer
2175 chips might think that the current transfer is still
2176 in progress. Reset the slave devices by sending start
2177 commands until the slave device responds.
2179 That's all that's required for CONFIG_HARD_I2C.
2181 If you use the software i2c interface (CONFIG_SYS_I2C_SOFT)
2182 then the following macros need to be defined (examples are
2183 from include/configs/lwmon.h):
2187 (Optional). Any commands necessary to enable the I2C
2188 controller or configure ports.
2190 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
2194 (Only for MPC8260 CPU). The I/O port to use (the code
2195 assumes both bits are on the same port). Valid values
2196 are 0..3 for ports A..D.
2200 The code necessary to make the I2C data line active
2201 (driven). If the data line is open collector, this
2204 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
2208 The code necessary to make the I2C data line tri-stated
2209 (inactive). If the data line is open collector, this
2212 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
2216 Code that returns true if the I2C data line is high,
2219 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
2223 If <bit> is true, sets the I2C data line high. If it
2224 is false, it clears it (low).
2226 eg: #define I2C_SDA(bit) \
2227 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
2228 else immr->im_cpm.cp_pbdat &= ~PB_SDA
2232 If <bit> is true, sets the I2C clock line high. If it
2233 is false, it clears it (low).
2235 eg: #define I2C_SCL(bit) \
2236 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
2237 else immr->im_cpm.cp_pbdat &= ~PB_SCL
2241 This delay is invoked four times per clock cycle so this
2242 controls the rate of data transfer. The data rate thus
2243 is 1 / (I2C_DELAY * 4). Often defined to be something
2246 #define I2C_DELAY udelay(2)
2248 CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
2250 If your arch supports the generic GPIO framework (asm/gpio.h),
2251 then you may alternatively define the two GPIOs that are to be
2252 used as SCL / SDA. Any of the previous I2C_xxx macros will
2253 have GPIO-based defaults assigned to them as appropriate.
2255 You should define these to the GPIO value as given directly to
2256 the generic GPIO functions.
2258 CONFIG_SYS_I2C_INIT_BOARD
2260 When a board is reset during an i2c bus transfer
2261 chips might think that the current transfer is still
2262 in progress. On some boards it is possible to access
2263 the i2c SCLK line directly, either by using the
2264 processor pin as a GPIO or by having a second pin
2265 connected to the bus. If this option is defined a
2266 custom i2c_init_board() routine in boards/xxx/board.c
2267 is run early in the boot sequence.
2269 CONFIG_SYS_I2C_BOARD_LATE_INIT
2271 An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
2272 defined a custom i2c_board_late_init() routine in
2273 boards/xxx/board.c is run AFTER the operations in i2c_init()
2274 is completed. This callpoint can be used to unreset i2c bus
2275 using CPU i2c controller register accesses for CPUs whose i2c
2276 controller provide such a method. It is called at the end of
2277 i2c_init() to allow i2c_init operations to setup the i2c bus
2278 controller on the CPU (e.g. setting bus speed & slave address).
2280 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
2282 This option enables configuration of bi_iic_fast[] flags
2283 in u-boot bd_info structure based on u-boot environment
2284 variable "i2cfast". (see also i2cfast)
2286 CONFIG_I2C_MULTI_BUS
2288 This option allows the use of multiple I2C buses, each of which
2289 must have a controller. At any point in time, only one bus is
2290 active. To switch to a different bus, use the 'i2c dev' command.
2291 Note that bus numbering is zero-based.
2293 CONFIG_SYS_I2C_NOPROBES
2295 This option specifies a list of I2C devices that will be skipped
2296 when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
2297 is set, specify a list of bus-device pairs. Otherwise, specify
2298 a 1D array of device addresses
2301 #undef CONFIG_I2C_MULTI_BUS
2302 #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
2304 will skip addresses 0x50 and 0x68 on a board with one I2C bus
2306 #define CONFIG_I2C_MULTI_BUS
2307 #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
2309 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
2311 CONFIG_SYS_SPD_BUS_NUM
2313 If defined, then this indicates the I2C bus number for DDR SPD.
2314 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
2316 CONFIG_SYS_RTC_BUS_NUM
2318 If defined, then this indicates the I2C bus number for the RTC.
2319 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
2321 CONFIG_SYS_DTT_BUS_NUM
2323 If defined, then this indicates the I2C bus number for the DTT.
2324 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
2326 CONFIG_SYS_I2C_DTT_ADDR:
2328 If defined, specifies the I2C address of the DTT device.
2329 If not defined, then U-Boot uses predefined value for
2330 specified DTT device.
2332 CONFIG_SOFT_I2C_READ_REPEATED_START
2334 defining this will force the i2c_read() function in
2335 the soft_i2c driver to perform an I2C repeated start
2336 between writing the address pointer and reading the
2337 data. If this define is omitted the default behaviour
2338 of doing a stop-start sequence will be used. Most I2C
2339 devices can use either method, but some require one or
2342 - SPI Support: CONFIG_SPI
2344 Enables SPI driver (so far only tested with
2345 SPI EEPROM, also an instance works with Crystal A/D and
2346 D/As on the SACSng board)
2350 Enables the driver for SPI controller on SuperH. Currently
2351 only SH7757 is supported.
2355 Enables extended (16-bit) SPI EEPROM addressing.
2356 (symmetrical to CONFIG_I2C_X)
2360 Enables a software (bit-bang) SPI driver rather than
2361 using hardware support. This is a general purpose
2362 driver that only requires three general I/O port pins
2363 (two outputs, one input) to function. If this is
2364 defined, the board configuration must define several
2365 SPI configuration items (port pins to use, etc). For
2366 an example, see include/configs/sacsng.h.
2370 Enables a hardware SPI driver for general-purpose reads
2371 and writes. As with CONFIG_SOFT_SPI, the board configuration
2372 must define a list of chip-select function pointers.
2373 Currently supported on some MPC8xxx processors. For an
2374 example, see include/configs/mpc8349emds.h.
2378 Enables the driver for the SPI controllers on i.MX and MXC
2379 SoCs. Currently i.MX31/35/51 are supported.
2381 - FPGA Support: CONFIG_FPGA
2383 Enables FPGA subsystem.
2385 CONFIG_FPGA_<vendor>
2387 Enables support for specific chip vendors.
2390 CONFIG_FPGA_<family>
2392 Enables support for FPGA family.
2393 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
2397 Specify the number of FPGA devices to support.
2399 CONFIG_SYS_FPGA_PROG_FEEDBACK
2401 Enable printing of hash marks during FPGA configuration.
2403 CONFIG_SYS_FPGA_CHECK_BUSY
2405 Enable checks on FPGA configuration interface busy
2406 status by the configuration function. This option
2407 will require a board or device specific function to
2412 If defined, a function that provides delays in the FPGA
2413 configuration driver.
2415 CONFIG_SYS_FPGA_CHECK_CTRLC
2416 Allow Control-C to interrupt FPGA configuration
2418 CONFIG_SYS_FPGA_CHECK_ERROR
2420 Check for configuration errors during FPGA bitfile
2421 loading. For example, abort during Virtex II
2422 configuration if the INIT_B line goes low (which
2423 indicated a CRC error).
2425 CONFIG_SYS_FPGA_WAIT_INIT
2427 Maximum time to wait for the INIT_B line to deassert
2428 after PROB_B has been deasserted during a Virtex II
2429 FPGA configuration sequence. The default time is 500
2432 CONFIG_SYS_FPGA_WAIT_BUSY
2434 Maximum time to wait for BUSY to deassert during
2435 Virtex II FPGA configuration. The default is 5 ms.
2437 CONFIG_SYS_FPGA_WAIT_CONFIG
2439 Time to wait after FPGA configuration. The default is
2442 - Configuration Management:
2445 If defined, this string will be added to the U-Boot
2446 version information (U_BOOT_VERSION)
2448 - Vendor Parameter Protection:
2450 U-Boot considers the values of the environment
2451 variables "serial#" (Board Serial Number) and
2452 "ethaddr" (Ethernet Address) to be parameters that
2453 are set once by the board vendor / manufacturer, and
2454 protects these variables from casual modification by
2455 the user. Once set, these variables are read-only,
2456 and write or delete attempts are rejected. You can
2457 change this behaviour:
2459 If CONFIG_ENV_OVERWRITE is #defined in your config
2460 file, the write protection for vendor parameters is
2461 completely disabled. Anybody can change or delete
2464 Alternatively, if you #define _both_ CONFIG_ETHADDR
2465 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
2466 Ethernet address is installed in the environment,
2467 which can be changed exactly ONCE by the user. [The
2468 serial# is unaffected by this, i. e. it remains
2471 The same can be accomplished in a more flexible way
2472 for any variable by configuring the type of access
2473 to allow for those variables in the ".flags" variable
2474 or define CONFIG_ENV_FLAGS_LIST_STATIC.
2479 Define this variable to enable the reservation of
2480 "protected RAM", i. e. RAM which is not overwritten
2481 by U-Boot. Define CONFIG_PRAM to hold the number of
2482 kB you want to reserve for pRAM. You can overwrite
2483 this default value by defining an environment
2484 variable "pram" to the number of kB you want to
2485 reserve. Note that the board info structure will
2486 still show the full amount of RAM. If pRAM is
2487 reserved, a new environment variable "mem" will
2488 automatically be defined to hold the amount of
2489 remaining RAM in a form that can be passed as boot
2490 argument to Linux, for instance like that:
2492 setenv bootargs ... mem=\${mem}
2495 This way you can tell Linux not to use this memory,
2496 either, which results in a memory region that will
2497 not be affected by reboots.
2499 *WARNING* If your board configuration uses automatic
2500 detection of the RAM size, you must make sure that
2501 this memory test is non-destructive. So far, the
2502 following board configurations are known to be
2505 IVMS8, IVML24, SPD8xx, TQM8xxL,
2506 HERMES, IP860, RPXlite, LWMON,
2509 - Access to physical memory region (> 4GB)
2510 Some basic support is provided for operations on memory not
2511 normally accessible to U-Boot - e.g. some architectures
2512 support access to more than 4GB of memory on 32-bit
2513 machines using physical address extension or similar.
2514 Define CONFIG_PHYSMEM to access this basic support, which
2515 currently only supports clearing the memory.
2520 Define this variable to stop the system in case of a
2521 fatal error, so that you have to reset it manually.
2522 This is probably NOT a good idea for an embedded
2523 system where you want the system to reboot
2524 automatically as fast as possible, but it may be
2525 useful during development since you can try to debug
2526 the conditions that lead to the situation.
2528 CONFIG_NET_RETRY_COUNT
2530 This variable defines the number of retries for
2531 network operations like ARP, RARP, TFTP, or BOOTP
2532 before giving up the operation. If not defined, a
2533 default value of 5 is used.
2537 Timeout waiting for an ARP reply in milliseconds.
2541 Timeout in milliseconds used in NFS protocol.
2542 If you encounter "ERROR: Cannot umount" in nfs command,
2543 try longer timeout such as
2544 #define CONFIG_NFS_TIMEOUT 10000UL
2546 - Command Interpreter:
2547 CONFIG_AUTO_COMPLETE
2549 Enable auto completion of commands using TAB.
2551 Note that this feature has NOT been implemented yet
2552 for the "hush" shell.
2555 CONFIG_SYS_HUSH_PARSER
2557 Define this variable to enable the "hush" shell (from
2558 Busybox) as command line interpreter, thus enabling
2559 powerful command line syntax like
2560 if...then...else...fi conditionals or `&&' and '||'
2561 constructs ("shell scripts").
2563 If undefined, you get the old, much simpler behaviour
2564 with a somewhat smaller memory footprint.
2567 CONFIG_SYS_PROMPT_HUSH_PS2
2569 This defines the secondary prompt string, which is
2570 printed when the command interpreter needs more input
2571 to complete a command. Usually "> ".
2575 In the current implementation, the local variables
2576 space and global environment variables space are
2577 separated. Local variables are those you define by
2578 simply typing `name=value'. To access a local
2579 variable later on, you have write `$name' or
2580 `${name}'; to execute the contents of a variable
2581 directly type `$name' at the command prompt.
2583 Global environment variables are those you use
2584 setenv/printenv to work with. To run a command stored
2585 in such a variable, you need to use the run command,
2586 and you must not use the '$' sign to access them.
2588 To store commands and special characters in a
2589 variable, please use double quotation marks
2590 surrounding the whole text of the variable, instead
2591 of the backslashes before semicolons and special
2594 - Commandline Editing and History:
2595 CONFIG_CMDLINE_EDITING
2597 Enable editing and History functions for interactive
2598 commandline input operations
2600 - Default Environment:
2601 CONFIG_EXTRA_ENV_SETTINGS
2603 Define this to contain any number of null terminated
2604 strings (variable = value pairs) that will be part of
2605 the default environment compiled into the boot image.
2607 For example, place something like this in your
2608 board's config file:
2610 #define CONFIG_EXTRA_ENV_SETTINGS \
2614 Warning: This method is based on knowledge about the
2615 internal format how the environment is stored by the
2616 U-Boot code. This is NOT an official, exported
2617 interface! Although it is unlikely that this format
2618 will change soon, there is no guarantee either.
2619 You better know what you are doing here.
2621 Note: overly (ab)use of the default environment is
2622 discouraged. Make sure to check other ways to preset
2623 the environment like the "source" command or the
2626 CONFIG_ENV_VARS_UBOOT_CONFIG
2628 Define this in order to add variables describing the
2629 U-Boot build configuration to the default environment.
2630 These will be named arch, cpu, board, vendor, and soc.
2632 Enabling this option will cause the following to be defined:
2640 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
2642 Define this in order to add variables describing certain
2643 run-time determined information about the hardware to the
2644 environment. These will be named board_name, board_rev.
2646 CONFIG_DELAY_ENVIRONMENT
2648 Normally the environment is loaded when the board is
2649 intialised so that it is available to U-Boot. This inhibits
2650 that so that the environment is not available until
2651 explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL
2652 this is instead controlled by the value of
2653 /config/load-environment.
2655 - DataFlash Support:
2656 CONFIG_HAS_DATAFLASH
2658 Defining this option enables DataFlash features and
2659 allows to read/write in Dataflash via the standard
2662 - Serial Flash support
2665 Defining this option enables SPI flash commands
2666 'sf probe/read/write/erase/update'.
2668 Usage requires an initial 'probe' to define the serial
2669 flash parameters, followed by read/write/erase/update
2672 The following defaults may be provided by the platform
2673 to handle the common case when only a single serial
2674 flash is present on the system.
2676 CONFIG_SF_DEFAULT_BUS Bus identifier
2677 CONFIG_SF_DEFAULT_CS Chip-select
2678 CONFIG_SF_DEFAULT_MODE (see include/spi.h)
2679 CONFIG_SF_DEFAULT_SPEED in Hz
2683 Define this option to include a destructive SPI flash
2686 CONFIG_SPI_FLASH_BAR Ban/Extended Addr Reg
2688 Define this option to use the Bank addr/Extended addr
2689 support on SPI flashes which has size > 16Mbytes.
2691 - SystemACE Support:
2694 Adding this option adds support for Xilinx SystemACE
2695 chips attached via some sort of local bus. The address
2696 of the chip must also be defined in the
2697 CONFIG_SYS_SYSTEMACE_BASE macro. For example:
2699 #define CONFIG_SYSTEMACE
2700 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
2702 When SystemACE support is added, the "ace" device type
2703 becomes available to the fat commands, i.e. fatls.
2705 - TFTP Fixed UDP Port:
2708 If this is defined, the environment variable tftpsrcp
2709 is used to supply the TFTP UDP source port value.
2710 If tftpsrcp isn't defined, the normal pseudo-random port
2711 number generator is used.
2713 Also, the environment variable tftpdstp is used to supply
2714 the TFTP UDP destination port value. If tftpdstp isn't
2715 defined, the normal port 69 is used.
2717 The purpose for tftpsrcp is to allow a TFTP server to
2718 blindly start the TFTP transfer using the pre-configured
2719 target IP address and UDP port. This has the effect of
2720 "punching through" the (Windows XP) firewall, allowing
2721 the remainder of the TFTP transfer to proceed normally.
2722 A better solution is to properly configure the firewall,
2723 but sometimes that is not allowed.
2728 This enables a generic 'hash' command which can produce
2729 hashes / digests from a few algorithms (e.g. SHA1, SHA256).
2733 Enable the hash verify command (hash -v). This adds to code
2736 CONFIG_SHA1 - support SHA1 hashing
2737 CONFIG_SHA256 - support SHA256 hashing
2739 Note: There is also a sha1sum command, which should perhaps
2740 be deprecated in favour of 'hash sha1'.
2742 - Freescale i.MX specific commands:
2743 CONFIG_CMD_HDMIDETECT
2744 This enables 'hdmidet' command which returns true if an
2745 HDMI monitor is detected. This command is i.MX 6 specific.
2748 This enables the 'bmode' (bootmode) command for forcing
2749 a boot from specific media.
2751 This is useful for forcing the ROM's usb downloader to
2752 activate upon a watchdog reset which is nice when iterating
2753 on U-Boot. Using the reset button or running bmode normal
2754 will set it back to normal. This command currently
2755 supports i.MX53 and i.MX6.
2760 This enables the RSA algorithm used for FIT image verification
2761 in U-Boot. See doc/uImage/signature for more information.
2763 The signing part is build into mkimage regardless of this
2767 - Show boot progress:
2768 CONFIG_SHOW_BOOT_PROGRESS
2770 Defining this option allows to add some board-
2771 specific code (calling a user-provided function
2772 "show_boot_progress(int)") that enables you to show
2773 the system's boot progress on some display (for
2774 example, some LED's) on your board. At the moment,
2775 the following checkpoints are implemented:
2777 - Detailed boot stage timing
2779 Define this option to get detailed timing of each stage
2780 of the boot process.
2782 CONFIG_BOOTSTAGE_USER_COUNT
2783 This is the number of available user bootstage records.
2784 Each time you call bootstage_mark(BOOTSTAGE_ID_ALLOC, ...)
2785 a new ID will be allocated from this stash. If you exceed
2786 the limit, recording will stop.
2788 CONFIG_BOOTSTAGE_REPORT
2789 Define this to print a report before boot, similar to this:
2791 Timer summary in microseconds:
2794 3,575,678 3,575,678 board_init_f start
2795 3,575,695 17 arch_cpu_init A9
2796 3,575,777 82 arch_cpu_init done
2797 3,659,598 83,821 board_init_r start
2798 3,910,375 250,777 main_loop
2799 29,916,167 26,005,792 bootm_start
2800 30,361,327 445,160 start_kernel
2802 CONFIG_CMD_BOOTSTAGE
2803 Add a 'bootstage' command which supports printing a report
2804 and un/stashing of bootstage data.
2806 CONFIG_BOOTSTAGE_FDT
2807 Stash the bootstage information in the FDT. A root 'bootstage'
2808 node is created with each bootstage id as a child. Each child
2809 has a 'name' property and either 'mark' containing the
2810 mark time in microsecond, or 'accum' containing the
2811 accumulated time for that bootstage id in microseconds.
2816 name = "board_init_f";
2825 Code in the Linux kernel can find this in /proc/devicetree.
2827 Legacy uImage format:
2830 1 common/cmd_bootm.c before attempting to boot an image
2831 -1 common/cmd_bootm.c Image header has bad magic number
2832 2 common/cmd_bootm.c Image header has correct magic number
2833 -2 common/cmd_bootm.c Image header has bad checksum
2834 3 common/cmd_bootm.c Image header has correct checksum
2835 -3 common/cmd_bootm.c Image data has bad checksum
2836 4 common/cmd_bootm.c Image data has correct checksum
2837 -4 common/cmd_bootm.c Image is for unsupported architecture
2838 5 common/cmd_bootm.c Architecture check OK
2839 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
2840 6 common/cmd_bootm.c Image Type check OK
2841 -6 common/cmd_bootm.c gunzip uncompression error
2842 -7 common/cmd_bootm.c Unimplemented compression type
2843 7 common/cmd_bootm.c Uncompression OK
2844 8 common/cmd_bootm.c No uncompress/copy overwrite error
2845 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
2847 9 common/image.c Start initial ramdisk verification
2848 -10 common/image.c Ramdisk header has bad magic number
2849 -11 common/image.c Ramdisk header has bad checksum
2850 10 common/image.c Ramdisk header is OK
2851 -12 common/image.c Ramdisk data has bad checksum
2852 11 common/image.c Ramdisk data has correct checksum
2853 12 common/image.c Ramdisk verification complete, start loading
2854 -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
2855 13 common/image.c Start multifile image verification
2856 14 common/image.c No initial ramdisk, no multifile, continue.
2858 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
2860 -30 arch/powerpc/lib/board.c Fatal error, hang the system
2861 -31 post/post.c POST test failed, detected by post_output_backlog()
2862 -32 post/post.c POST test failed, detected by post_run_single()
2864 34 common/cmd_doc.c before loading a Image from a DOC device
2865 -35 common/cmd_doc.c Bad usage of "doc" command
2866 35 common/cmd_doc.c correct usage of "doc" command
2867 -36 common/cmd_doc.c No boot device
2868 36 common/cmd_doc.c correct boot device
2869 -37 common/cmd_doc.c Unknown Chip ID on boot device
2870 37 common/cmd_doc.c correct chip ID found, device available
2871 -38 common/cmd_doc.c Read Error on boot device
2872 38 common/cmd_doc.c reading Image header from DOC device OK
2873 -39 common/cmd_doc.c Image header has bad magic number
2874 39 common/cmd_doc.c Image header has correct magic number
2875 -40 common/cmd_doc.c Error reading Image from DOC device
2876 40 common/cmd_doc.c Image header has correct magic number
2877 41 common/cmd_ide.c before loading a Image from a IDE device
2878 -42 common/cmd_ide.c Bad usage of "ide" command
2879 42 common/cmd_ide.c correct usage of "ide" command
2880 -43 common/cmd_ide.c No boot device
2881 43 common/cmd_ide.c boot device found
2882 -44 common/cmd_ide.c Device not available
2883 44 common/cmd_ide.c Device available
2884 -45 common/cmd_ide.c wrong partition selected
2885 45 common/cmd_ide.c partition selected
2886 -46 common/cmd_ide.c Unknown partition table
2887 46 common/cmd_ide.c valid partition table found
2888 -47 common/cmd_ide.c Invalid partition type
2889 47 common/cmd_ide.c correct partition type
2890 -48 common/cmd_ide.c Error reading Image Header on boot device
2891 48 common/cmd_ide.c reading Image Header from IDE device OK
2892 -49 common/cmd_ide.c Image header has bad magic number
2893 49 common/cmd_ide.c Image header has correct magic number
2894 -50 common/cmd_ide.c Image header has bad checksum
2895 50 common/cmd_ide.c Image header has correct checksum
2896 -51 common/cmd_ide.c Error reading Image from IDE device
2897 51 common/cmd_ide.c reading Image from IDE device OK
2898 52 common/cmd_nand.c before loading a Image from a NAND device
2899 -53 common/cmd_nand.c Bad usage of "nand" command
2900 53 common/cmd_nand.c correct usage of "nand" command
2901 -54 common/cmd_nand.c No boot device
2902 54 common/cmd_nand.c boot device found
2903 -55 common/cmd_nand.c Unknown Chip ID on boot device
2904 55 common/cmd_nand.c correct chip ID found, device available
2905 -56 common/cmd_nand.c Error reading Image Header on boot device
2906 56 common/cmd_nand.c reading Image Header from NAND device OK
2907 -57 common/cmd_nand.c Image header has bad magic number
2908 57 common/cmd_nand.c Image header has correct magic number
2909 -58 common/cmd_nand.c Error reading Image from NAND device
2910 58 common/cmd_nand.c reading Image from NAND device OK
2912 -60 common/env_common.c Environment has a bad CRC, using default
2914 64 net/eth.c starting with Ethernet configuration.
2915 -64 net/eth.c no Ethernet found.
2916 65 net/eth.c Ethernet found.
2918 -80 common/cmd_net.c usage wrong
2919 80 common/cmd_net.c before calling NetLoop()
2920 -81 common/cmd_net.c some error in NetLoop() occurred
2921 81 common/cmd_net.c NetLoop() back without error
2922 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
2923 82 common/cmd_net.c trying automatic boot
2924 83 common/cmd_net.c running "source" command
2925 -83 common/cmd_net.c some error in automatic boot or "source" command
2926 84 common/cmd_net.c end without errors
2931 100 common/cmd_bootm.c Kernel FIT Image has correct format
2932 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
2933 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
2934 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
2935 102 common/cmd_bootm.c Kernel unit name specified
2936 -103 common/cmd_bootm.c Can't get kernel subimage node offset
2937 103 common/cmd_bootm.c Found configuration node
2938 104 common/cmd_bootm.c Got kernel subimage node offset
2939 -104 common/cmd_bootm.c Kernel subimage hash verification failed
2940 105 common/cmd_bootm.c Kernel subimage hash verification OK
2941 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
2942 106 common/cmd_bootm.c Architecture check OK
2943 -106 common/cmd_bootm.c Kernel subimage has wrong type
2944 107 common/cmd_bootm.c Kernel subimage type OK
2945 -107 common/cmd_bootm.c Can't get kernel subimage data/size
2946 108 common/cmd_bootm.c Got kernel subimage data/size
2947 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
2948 -109 common/cmd_bootm.c Can't get kernel subimage type
2949 -110 common/cmd_bootm.c Can't get kernel subimage comp
2950 -111 common/cmd_bootm.c Can't get kernel subimage os
2951 -112 common/cmd_bootm.c Can't get kernel subimage load address
2952 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
2954 120 common/image.c Start initial ramdisk verification
2955 -120 common/image.c Ramdisk FIT image has incorrect format
2956 121 common/image.c Ramdisk FIT image has correct format
2957 122 common/image.c No ramdisk subimage unit name, using configuration
2958 -122 common/image.c Can't get configuration for ramdisk subimage
2959 123 common/image.c Ramdisk unit name specified
2960 -124 common/image.c Can't get ramdisk subimage node offset
2961 125 common/image.c Got ramdisk subimage node offset
2962 -125 common/image.c Ramdisk subimage hash verification failed
2963 126 common/image.c Ramdisk subimage hash verification OK
2964 -126 common/image.c Ramdisk subimage for unsupported architecture
2965 127 common/image.c Architecture check OK
2966 -127 common/image.c Can't get ramdisk subimage data/size
2967 128 common/image.c Got ramdisk subimage data/size
2968 129 common/image.c Can't get ramdisk load address
2969 -129 common/image.c Got ramdisk load address
2971 -130 common/cmd_doc.c Incorrect FIT image format
2972 131 common/cmd_doc.c FIT image format OK
2974 -140 common/cmd_ide.c Incorrect FIT image format
2975 141 common/cmd_ide.c FIT image format OK
2977 -150 common/cmd_nand.c Incorrect FIT image format
2978 151 common/cmd_nand.c FIT image format OK
2980 - FIT image support:
2982 Enable support for the FIT uImage format.
2984 CONFIG_FIT_BEST_MATCH
2985 When no configuration is explicitly selected, default to the
2986 one whose fdt's compatibility field best matches that of
2987 U-Boot itself. A match is considered "best" if it matches the
2988 most specific compatibility entry of U-Boot's fdt's root node.
2989 The order of entries in the configuration's fdt is ignored.
2991 CONFIG_FIT_SIGNATURE
2992 This option enables signature verification of FIT uImages,
2993 using a hash signed and verified using RSA. See
2994 doc/uImage.FIT/signature.txt for more details.
2996 - Standalone program support:
2997 CONFIG_STANDALONE_LOAD_ADDR
2999 This option defines a board specific value for the
3000 address where standalone program gets loaded, thus
3001 overwriting the architecture dependent default
3004 - Frame Buffer Address:
3007 Define CONFIG_FB_ADDR if you want to use specific
3008 address for frame buffer. This is typically the case
3009 when using a graphics controller has separate video
3010 memory. U-Boot will then place the frame buffer at
3011 the given address instead of dynamically reserving it
3012 in system RAM by calling lcd_setmem(), which grabs
3013 the memory for the frame buffer depending on the
3014 configured panel size.
3016 Please see board_init_f function.
3018 - Automatic software updates via TFTP server
3020 CONFIG_UPDATE_TFTP_CNT_MAX
3021 CONFIG_UPDATE_TFTP_MSEC_MAX
3023 These options enable and control the auto-update feature;
3024 for a more detailed description refer to doc/README.update.
3026 - MTD Support (mtdparts command, UBI support)
3029 Adds the MTD device infrastructure from the Linux kernel.
3030 Needed for mtdparts command support.
3032 CONFIG_MTD_PARTITIONS
3034 Adds the MTD partitioning infrastructure from the Linux
3035 kernel. Needed for UBI support.
3040 Adds commands for interacting with MTD partitions formatted
3041 with the UBI flash translation layer
3043 Requires also defining CONFIG_RBTREE
3045 CONFIG_UBI_SILENCE_MSG
3047 Make the verbose messages from UBI stop printing. This leaves
3048 warnings and errors enabled.
3053 Adds commands for interacting with UBI volumes formatted as
3054 UBIFS. UBIFS is read-only in u-boot.
3056 Requires UBI support as well as CONFIG_LZO
3058 CONFIG_UBIFS_SILENCE_MSG
3060 Make the verbose messages from UBIFS stop printing. This leaves
3061 warnings and errors enabled.
3065 Enable building of SPL globally.
3068 LDSCRIPT for linking the SPL binary.
3070 CONFIG_SPL_MAX_FOOTPRINT
3071 Maximum size in memory allocated to the SPL, BSS included.
3072 When defined, the linker checks that the actual memory
3073 used by SPL from _start to __bss_end does not exceed it.
3074 CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
3075 must not be both defined at the same time.
3078 Maximum size of the SPL image (text, data, rodata, and
3079 linker lists sections), BSS excluded.
3080 When defined, the linker checks that the actual size does
3083 CONFIG_SPL_TEXT_BASE
3084 TEXT_BASE for linking the SPL binary.
3086 CONFIG_SPL_RELOC_TEXT_BASE
3087 Address to relocate to. If unspecified, this is equal to
3088 CONFIG_SPL_TEXT_BASE (i.e. no relocation is done).
3090 CONFIG_SPL_BSS_START_ADDR
3091 Link address for the BSS within the SPL binary.
3093 CONFIG_SPL_BSS_MAX_SIZE
3094 Maximum size in memory allocated to the SPL BSS.
3095 When defined, the linker checks that the actual memory used
3096 by SPL from __bss_start to __bss_end does not exceed it.
3097 CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
3098 must not be both defined at the same time.
3101 Adress of the start of the stack SPL will use
3103 CONFIG_SPL_RELOC_STACK
3104 Adress of the start of the stack SPL will use after
3105 relocation. If unspecified, this is equal to
3108 CONFIG_SYS_SPL_MALLOC_START
3109 Starting address of the malloc pool used in SPL.
3111 CONFIG_SYS_SPL_MALLOC_SIZE
3112 The size of the malloc pool used in SPL.
3114 CONFIG_SPL_FRAMEWORK
3115 Enable the SPL framework under common/. This framework
3116 supports MMC, NAND and YMODEM loading of U-Boot and NAND
3117 NAND loading of the Linux Kernel.
3119 CONFIG_SPL_DISPLAY_PRINT
3120 For ARM, enable an optional function to print more information
3121 about the running system.
3123 CONFIG_SPL_INIT_MINIMAL
3124 Arch init code should be built for a very small image
3126 CONFIG_SPL_LIBCOMMON_SUPPORT
3127 Support for common/libcommon.o in SPL binary
3129 CONFIG_SPL_LIBDISK_SUPPORT
3130 Support for disk/libdisk.o in SPL binary
3132 CONFIG_SPL_I2C_SUPPORT
3133 Support for drivers/i2c/libi2c.o in SPL binary
3135 CONFIG_SPL_GPIO_SUPPORT
3136 Support for drivers/gpio/libgpio.o in SPL binary
3138 CONFIG_SPL_MMC_SUPPORT
3139 Support for drivers/mmc/libmmc.o in SPL binary
3141 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
3142 CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
3143 CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION
3144 Address, size and partition on the MMC to load U-Boot from
3145 when the MMC is being used in raw mode.
3147 CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
3148 Sector to load kernel uImage from when MMC is being
3149 used in raw mode (for Falcon mode)
3151 CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR,
3152 CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
3153 Sector and number of sectors to load kernel argument
3154 parameters from when MMC is being used in raw mode
3157 CONFIG_SPL_FAT_SUPPORT
3158 Support for fs/fat/libfat.o in SPL binary
3160 CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
3161 Filename to read to load U-Boot when reading from FAT
3163 CONFIG_SPL_FAT_LOAD_KERNEL_NAME
3164 Filename to read to load kernel uImage when reading
3165 from FAT (for Falcon mode)
3167 CONFIG_SPL_FAT_LOAD_ARGS_NAME
3168 Filename to read to load kernel argument parameters
3169 when reading from FAT (for Falcon mode)
3171 CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
3172 Set this for NAND SPL on PPC mpc83xx targets, so that
3173 start.S waits for the rest of the SPL to load before
3174 continuing (the hardware starts execution after just
3175 loading the first page rather than the full 4K).
3177 CONFIG_SPL_NAND_BASE
3178 Include nand_base.c in the SPL. Requires
3179 CONFIG_SPL_NAND_DRIVERS.
3181 CONFIG_SPL_NAND_DRIVERS
3182 SPL uses normal NAND drivers, not minimal drivers.
3185 Include standard software ECC in the SPL
3187 CONFIG_SPL_NAND_SIMPLE
3188 Support for NAND boot using simple NAND drivers that
3189 expose the cmd_ctrl() interface.
3191 CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
3192 Set for the SPL on PPC mpc8xxx targets, support for
3193 arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary.
3195 CONFIG_SPL_COMMON_INIT_DDR
3196 Set for common ddr init with serial presence detect in
3199 CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
3200 CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
3201 CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
3202 CONFIG_SYS_NAND_ECCPOS, CONFIG_SYS_NAND_ECCSIZE,
3203 CONFIG_SYS_NAND_ECCBYTES
3204 Defines the size and behavior of the NAND that SPL uses
3207 CONFIG_SYS_NAND_U_BOOT_OFFS
3208 Location in NAND to read U-Boot from
3210 CONFIG_SYS_NAND_U_BOOT_DST
3211 Location in memory to load U-Boot to
3213 CONFIG_SYS_NAND_U_BOOT_SIZE
3214 Size of image to load
3216 CONFIG_SYS_NAND_U_BOOT_START
3217 Entry point in loaded image to jump to
3219 CONFIG_SYS_NAND_HW_ECC_OOBFIRST
3220 Define this if you need to first read the OOB and then the
3221 data. This is used for example on davinci plattforms.
3223 CONFIG_SPL_OMAP3_ID_NAND
3224 Support for an OMAP3-specific set of functions to return the
3225 ID and MFR of the first attached NAND chip, if present.
3227 CONFIG_SPL_SERIAL_SUPPORT
3228 Support for drivers/serial/libserial.o in SPL binary
3230 CONFIG_SPL_SPI_FLASH_SUPPORT
3231 Support for drivers/mtd/spi/libspi_flash.o in SPL binary
3233 CONFIG_SPL_SPI_SUPPORT
3234 Support for drivers/spi/libspi.o in SPL binary
3236 CONFIG_SPL_RAM_DEVICE
3237 Support for running image already present in ram, in SPL binary
3239 CONFIG_SPL_LIBGENERIC_SUPPORT
3240 Support for lib/libgeneric.o in SPL binary
3242 CONFIG_SPL_ENV_SUPPORT
3243 Support for the environment operating in SPL binary
3245 CONFIG_SPL_NET_SUPPORT
3246 Support for the net/libnet.o in SPL binary.
3247 It conflicts with SPL env from storage medium specified by
3248 CONFIG_ENV_IS_xxx but CONFIG_ENV_IS_NOWHERE
3251 Image offset to which the SPL should be padded before appending
3252 the SPL payload. By default, this is defined as
3253 CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
3254 CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
3255 payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
3258 Final target image containing SPL and payload. Some SPLs
3259 use an arch-specific makefile fragment instead, for
3260 example if more than one image needs to be produced.
3262 CONFIG_FIT_SPL_PRINT
3263 Printing information about a FIT image adds quite a bit of
3264 code to SPL. So this is normally disabled in SPL. Use this
3265 option to re-enable it. This will affect the output of the
3266 bootm command when booting a FIT image.
3270 Enable building of TPL globally.
3273 Image offset to which the TPL should be padded before appending
3274 the TPL payload. By default, this is defined as
3275 CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
3276 CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
3277 payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
3282 [so far only for SMDK2400 boards]
3284 - Modem support enable:
3285 CONFIG_MODEM_SUPPORT
3287 - RTS/CTS Flow control enable:
3290 - Modem debug support:
3291 CONFIG_MODEM_SUPPORT_DEBUG
3293 Enables debugging stuff (char screen[1024], dbg())
3294 for modem support. Useful only with BDI2000.
3296 - Interrupt support (PPC):
3298 There are common interrupt_init() and timer_interrupt()
3299 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
3300 for CPU specific initialization. interrupt_init_cpu()
3301 should set decrementer_count to appropriate value. If
3302 CPU resets decrementer automatically after interrupt
3303 (ppc4xx) it should set decrementer_count to zero.
3304 timer_interrupt() calls timer_interrupt_cpu() for CPU
3305 specific handling. If board has watchdog / status_led
3306 / other_activity_monitor it works automatically from
3307 general timer_interrupt().
3311 In the target system modem support is enabled when a
3312 specific key (key combination) is pressed during
3313 power-on. Otherwise U-Boot will boot normally
3314 (autoboot). The key_pressed() function is called from
3315 board_init(). Currently key_pressed() is a dummy
3316 function, returning 1 and thus enabling modem
3319 If there are no modem init strings in the
3320 environment, U-Boot proceed to autoboot; the
3321 previous output (banner, info printfs) will be
3324 See also: doc/README.Modem
3326 Board initialization settings:
3327 ------------------------------
3329 During Initialization u-boot calls a number of board specific functions
3330 to allow the preparation of board specific prerequisites, e.g. pin setup
3331 before drivers are initialized. To enable these callbacks the
3332 following configuration macros have to be defined. Currently this is
3333 architecture specific, so please check arch/your_architecture/lib/board.c
3334 typically in board_init_f() and board_init_r().
3336 - CONFIG_BOARD_EARLY_INIT_F: Call board_early_init_f()
3337 - CONFIG_BOARD_EARLY_INIT_R: Call board_early_init_r()
3338 - CONFIG_BOARD_LATE_INIT: Call board_late_init()
3339 - CONFIG_BOARD_POSTCLK_INIT: Call board_postclk_init()
3341 Configuration Settings:
3342 -----------------------
3344 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
3345 undefine this when you're short of memory.
3347 - CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
3348 width of the commands listed in the 'help' command output.
3350 - CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
3351 prompt for user input.
3353 - CONFIG_SYS_CBSIZE: Buffer size for input from the Console
3355 - CONFIG_SYS_PBSIZE: Buffer size for Console output
3357 - CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
3359 - CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to
3360 the application (usually a Linux kernel) when it is
3363 - CONFIG_SYS_BAUDRATE_TABLE:
3364 List of legal baudrate settings for this board.
3366 - CONFIG_SYS_CONSOLE_INFO_QUIET
3367 Suppress display of console information at boot.
3369 - CONFIG_SYS_CONSOLE_IS_IN_ENV
3370 If the board specific function
3371 extern int overwrite_console (void);
3372 returns 1, the stdin, stderr and stdout are switched to the
3373 serial port, else the settings in the environment are used.
3375 - CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
3376 Enable the call to overwrite_console().
3378 - CONFIG_SYS_CONSOLE_ENV_OVERWRITE
3379 Enable overwrite of previous console environment settings.
3381 - CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
3382 Begin and End addresses of the area used by the
3385 - CONFIG_SYS_ALT_MEMTEST:
3386 Enable an alternate, more extensive memory test.
3388 - CONFIG_SYS_MEMTEST_SCRATCH:
3389 Scratch address used by the alternate memory test
3390 You only need to set this if address zero isn't writeable
3392 - CONFIG_SYS_MEM_TOP_HIDE (PPC only):
3393 If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
3394 this specified memory area will get subtracted from the top
3395 (end) of RAM and won't get "touched" at all by U-Boot. By
3396 fixing up gd->ram_size the Linux kernel should gets passed
3397 the now "corrected" memory size and won't touch it either.
3398 This should work for arch/ppc and arch/powerpc. Only Linux
3399 board ports in arch/powerpc with bootwrapper support that
3400 recalculate the memory size from the SDRAM controller setup
3401 will have to get fixed in Linux additionally.
3403 This option can be used as a workaround for the 440EPx/GRx
3404 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
3407 WARNING: Please make sure that this value is a multiple of
3408 the Linux page size (normally 4k). If this is not the case,
3409 then the end address of the Linux memory will be located at a
3410 non page size aligned address and this could cause major
3413 - CONFIG_SYS_LOADS_BAUD_CHANGE:
3414 Enable temporary baudrate change while serial download
3416 - CONFIG_SYS_SDRAM_BASE:
3417 Physical start address of SDRAM. _Must_ be 0 here.
3419 - CONFIG_SYS_MBIO_BASE:
3420 Physical start address of Motherboard I/O (if using a
3423 - CONFIG_SYS_FLASH_BASE:
3424 Physical start address of Flash memory.
3426 - CONFIG_SYS_MONITOR_BASE:
3427 Physical start address of boot monitor code (set by
3428 make config files to be same as the text base address
3429 (CONFIG_SYS_TEXT_BASE) used when linking) - same as
3430 CONFIG_SYS_FLASH_BASE when booting from flash.
3432 - CONFIG_SYS_MONITOR_LEN:
3433 Size of memory reserved for monitor code, used to
3434 determine _at_compile_time_ (!) if the environment is
3435 embedded within the U-Boot image, or in a separate
3438 - CONFIG_SYS_MALLOC_LEN:
3439 Size of DRAM reserved for malloc() use.
3441 - CONFIG_SYS_BOOTM_LEN:
3442 Normally compressed uImages are limited to an
3443 uncompressed size of 8 MBytes. If this is not enough,
3444 you can define CONFIG_SYS_BOOTM_LEN in your board config file
3445 to adjust this setting to your needs.
3447 - CONFIG_SYS_BOOTMAPSZ:
3448 Maximum size of memory mapped by the startup code of
3449 the Linux kernel; all data that must be processed by
3450 the Linux kernel (bd_info, boot arguments, FDT blob if
3451 used) must be put below this limit, unless "bootm_low"
3452 environment variable is defined and non-zero. In such case
3453 all data for the Linux kernel must be between "bootm_low"
3454 and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
3455 variable "bootm_mapsize" will override the value of
3456 CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
3457 then the value in "bootm_size" will be used instead.
3459 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
3460 Enable initrd_high functionality. If defined then the
3461 initrd_high feature is enabled and the bootm ramdisk subcommand
3464 - CONFIG_SYS_BOOT_GET_CMDLINE:
3465 Enables allocating and saving kernel cmdline in space between
3466 "bootm_low" and "bootm_low" + BOOTMAPSZ.
3468 - CONFIG_SYS_BOOT_GET_KBD:
3469 Enables allocating and saving a kernel copy of the bd_info in
3470 space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
3472 - CONFIG_SYS_MAX_FLASH_BANKS:
3473 Max number of Flash memory banks
3475 - CONFIG_SYS_MAX_FLASH_SECT:
3476 Max number of sectors on a Flash chip
3478 - CONFIG_SYS_FLASH_ERASE_TOUT:
3479 Timeout for Flash erase operations (in ms)
3481 - CONFIG_SYS_FLASH_WRITE_TOUT:
3482 Timeout for Flash write operations (in ms)
3484 - CONFIG_SYS_FLASH_LOCK_TOUT
3485 Timeout for Flash set sector lock bit operation (in ms)
3487 - CONFIG_SYS_FLASH_UNLOCK_TOUT
3488 Timeout for Flash clear lock bits operation (in ms)
3490 - CONFIG_SYS_FLASH_PROTECTION
3491 If defined, hardware flash sectors protection is used
3492 instead of U-Boot software protection.
3494 - CONFIG_SYS_DIRECT_FLASH_TFTP:
3496 Enable TFTP transfers directly to flash memory;
3497 without this option such a download has to be
3498 performed in two steps: (1) download to RAM, and (2)
3499 copy from RAM to flash.
3501 The two-step approach is usually more reliable, since
3502 you can check if the download worked before you erase
3503 the flash, but in some situations (when system RAM is
3504 too limited to allow for a temporary copy of the
3505 downloaded image) this option may be very useful.
3507 - CONFIG_SYS_FLASH_CFI:
3508 Define if the flash driver uses extra elements in the
3509 common flash structure for storing flash geometry.
3511 - CONFIG_FLASH_CFI_DRIVER
3512 This option also enables the building of the cfi_flash driver
3513 in the drivers directory
3515 - CONFIG_FLASH_CFI_MTD
3516 This option enables the building of the cfi_mtd driver
3517 in the drivers directory. The driver exports CFI flash
3520 - CONFIG_SYS_FLASH_USE_BUFFER_WRITE
3521 Use buffered writes to flash.
3523 - CONFIG_FLASH_SPANSION_S29WS_N
3524 s29ws-n MirrorBit flash has non-standard addresses for buffered
3527 - CONFIG_SYS_FLASH_QUIET_TEST
3528 If this option is defined, the common CFI flash doesn't
3529 print it's warning upon not recognized FLASH banks. This
3530 is useful, if some of the configured banks are only
3531 optionally available.
3533 - CONFIG_FLASH_SHOW_PROGRESS
3534 If defined (must be an integer), print out countdown
3535 digits and dots. Recommended value: 45 (9..1) for 80
3536 column displays, 15 (3..1) for 40 column displays.
3538 - CONFIG_FLASH_VERIFY
3539 If defined, the content of the flash (destination) is compared
3540 against the source after the write operation. An error message
3541 will be printed when the contents are not identical.
3542 Please note that this option is useless in nearly all cases,
3543 since such flash programming errors usually are detected earlier
3544 while unprotecting/erasing/programming. Please only enable
3545 this option if you really know what you are doing.
3547 - CONFIG_SYS_RX_ETH_BUFFER:
3548 Defines the number of Ethernet receive buffers. On some
3549 Ethernet controllers it is recommended to set this value
3550 to 8 or even higher (EEPRO100 or 405 EMAC), since all
3551 buffers can be full shortly after enabling the interface
3552 on high Ethernet traffic.
3553 Defaults to 4 if not defined.
3555 - CONFIG_ENV_MAX_ENTRIES
3557 Maximum number of entries in the hash table that is used
3558 internally to store the environment settings. The default
3559 setting is supposed to be generous and should work in most
3560 cases. This setting can be used to tune behaviour; see
3561 lib/hashtable.c for details.
3563 - CONFIG_ENV_FLAGS_LIST_DEFAULT
3564 - CONFIG_ENV_FLAGS_LIST_STATIC
3565 Enable validation of the values given to environment variables when
3566 calling env set. Variables can be restricted to only decimal,
3567 hexadecimal, or boolean. If CONFIG_CMD_NET is also defined,
3568 the variables can also be restricted to IP address or MAC address.
3570 The format of the list is:
3571 type_attribute = [s|d|x|b|i|m]
3572 access_atribute = [a|r|o|c]
3573 attributes = type_attribute[access_atribute]
3574 entry = variable_name[:attributes]
3577 The type attributes are:
3578 s - String (default)
3581 b - Boolean ([1yYtT|0nNfF])
3585 The access attributes are:
3591 - CONFIG_ENV_FLAGS_LIST_DEFAULT
3592 Define this to a list (string) to define the ".flags"
3593 envirnoment variable in the default or embedded environment.
3595 - CONFIG_ENV_FLAGS_LIST_STATIC
3596 Define this to a list (string) to define validation that
3597 should be done if an entry is not found in the ".flags"
3598 environment variable. To override a setting in the static
3599 list, simply add an entry for the same variable name to the
3602 - CONFIG_ENV_ACCESS_IGNORE_FORCE
3603 If defined, don't allow the -f switch to env set override variable
3606 - CONFIG_SYS_GENERIC_BOARD
3607 This selects the architecture-generic board system instead of the
3608 architecture-specific board files. It is intended to move boards
3609 to this new framework over time. Defining this will disable the
3610 arch/foo/lib/board.c file and use common/board_f.c and
3611 common/board_r.c instead. To use this option your architecture
3612 must support it (i.e. must define __HAVE_ARCH_GENERIC_BOARD in
3613 its config.mk file). If you find problems enabling this option on
3614 your board please report the problem and send patches!
3616 - CONFIG_SYS_SYM_OFFSETS
3617 This is set by architectures that use offsets for link symbols
3618 instead of absolute values. So bss_start is obtained using an
3619 offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
3620 directly. You should not need to touch this setting.
3622 - CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
3623 This is set by OMAP boards for the max time that reset should
3624 be asserted. See doc/README.omap-reset-time for details on how
3625 the value can be calulated on a given board.
3627 The following definitions that deal with the placement and management
3628 of environment data (variable area); in general, we support the
3629 following configurations:
3631 - CONFIG_BUILD_ENVCRC:
3633 Builds up envcrc with the target environment so that external utils
3634 may easily extract it and embed it in final U-Boot images.
3636 - CONFIG_ENV_IS_IN_FLASH:
3638 Define this if the environment is in flash memory.
3640 a) The environment occupies one whole flash sector, which is
3641 "embedded" in the text segment with the U-Boot code. This
3642 happens usually with "bottom boot sector" or "top boot
3643 sector" type flash chips, which have several smaller
3644 sectors at the start or the end. For instance, such a
3645 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
3646 such a case you would place the environment in one of the
3647 4 kB sectors - with U-Boot code before and after it. With
3648 "top boot sector" type flash chips, you would put the
3649 environment in one of the last sectors, leaving a gap
3650 between U-Boot and the environment.
3652 - CONFIG_ENV_OFFSET:
3654 Offset of environment data (variable area) to the
3655 beginning of flash memory; for instance, with bottom boot
3656 type flash chips the second sector can be used: the offset
3657 for this sector is given here.
3659 CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
3663 This is just another way to specify the start address of
3664 the flash sector containing the environment (instead of
3667 - CONFIG_ENV_SECT_SIZE:
3669 Size of the sector containing the environment.
3672 b) Sometimes flash chips have few, equal sized, BIG sectors.
3673 In such a case you don't want to spend a whole sector for
3678 If you use this in combination with CONFIG_ENV_IS_IN_FLASH
3679 and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
3680 of this flash sector for the environment. This saves
3681 memory for the RAM copy of the environment.
3683 It may also save flash memory if you decide to use this
3684 when your environment is "embedded" within U-Boot code,
3685 since then the remainder of the flash sector could be used
3686 for U-Boot code. It should be pointed out that this is
3687 STRONGLY DISCOURAGED from a robustness point of view:
3688 updating the environment in flash makes it always
3689 necessary to erase the WHOLE sector. If something goes
3690 wrong before the contents has been restored from a copy in
3691 RAM, your target system will be dead.
3693 - CONFIG_ENV_ADDR_REDUND
3694 CONFIG_ENV_SIZE_REDUND
3696 These settings describe a second storage area used to hold
3697 a redundant copy of the environment data, so that there is
3698 a valid backup copy in case there is a power failure during
3699 a "saveenv" operation.
3701 BE CAREFUL! Any changes to the flash layout, and some changes to the
3702 source code will make it necessary to adapt <board>/u-boot.lds*
3706 - CONFIG_ENV_IS_IN_NVRAM:
3708 Define this if you have some non-volatile memory device
3709 (NVRAM, battery buffered SRAM) which you want to use for the
3715 These two #defines are used to determine the memory area you
3716 want to use for environment. It is assumed that this memory
3717 can just be read and written to, without any special
3720 BE CAREFUL! The first access to the environment happens quite early
3721 in U-Boot initalization (when we try to get the setting of for the
3722 console baudrate). You *MUST* have mapped your NVRAM area then, or
3725 Please note that even with NVRAM we still use a copy of the
3726 environment in RAM: we could work on NVRAM directly, but we want to
3727 keep settings there always unmodified except somebody uses "saveenv"
3728 to save the current settings.
3731 - CONFIG_ENV_IS_IN_EEPROM:
3733 Use this if you have an EEPROM or similar serial access
3734 device and a driver for it.
3736 - CONFIG_ENV_OFFSET:
3739 These two #defines specify the offset and size of the
3740 environment area within the total memory of your EEPROM.
3742 - CONFIG_SYS_I2C_EEPROM_ADDR:
3743 If defined, specified the chip address of the EEPROM device.
3744 The default address is zero.
3746 - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
3747 If defined, the number of bits used to address bytes in a
3748 single page in the EEPROM device. A 64 byte page, for example
3749 would require six bits.
3751 - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
3752 If defined, the number of milliseconds to delay between
3753 page writes. The default is zero milliseconds.
3755 - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
3756 The length in bytes of the EEPROM memory array address. Note
3757 that this is NOT the chip address length!
3759 - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
3760 EEPROM chips that implement "address overflow" are ones
3761 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
3762 address and the extra bits end up in the "chip address" bit
3763 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
3766 Note that we consider the length of the address field to
3767 still be one byte because the extra address bits are hidden
3768 in the chip address.
3770 - CONFIG_SYS_EEPROM_SIZE:
3771 The size in bytes of the EEPROM device.
3773 - CONFIG_ENV_EEPROM_IS_ON_I2C
3774 define this, if you have I2C and SPI activated, and your
3775 EEPROM, which holds the environment, is on the I2C bus.
3777 - CONFIG_I2C_ENV_EEPROM_BUS
3778 if you have an Environment on an EEPROM reached over
3779 I2C muxes, you can define here, how to reach this
3780 EEPROM. For example:
3782 #define CONFIG_I2C_ENV_EEPROM_BUS 1
3784 EEPROM which holds the environment, is reached over
3785 a pca9547 i2c mux with address 0x70, channel 3.
3787 - CONFIG_ENV_IS_IN_DATAFLASH:
3789 Define this if you have a DataFlash memory device which you
3790 want to use for the environment.
3792 - CONFIG_ENV_OFFSET:
3796 These three #defines specify the offset and size of the
3797 environment area within the total memory of your DataFlash placed
3798 at the specified address.
3800 - CONFIG_ENV_IS_IN_REMOTE:
3802 Define this if you have a remote memory space which you
3803 want to use for the local device's environment.
3808 These two #defines specify the address and size of the
3809 environment area within the remote memory space. The
3810 local device can get the environment from remote memory
3811 space by SRIO or PCIE links.
3813 BE CAREFUL! For some special cases, the local device can not use
3814 "saveenv" command. For example, the local device will get the
3815 environment stored in a remote NOR flash by SRIO or PCIE link,
3816 but it can not erase, write this NOR flash by SRIO or PCIE interface.
3818 - CONFIG_ENV_IS_IN_NAND:
3820 Define this if you have a NAND device which you want to use
3821 for the environment.
3823 - CONFIG_ENV_OFFSET:
3826 These two #defines specify the offset and size of the environment
3827 area within the first NAND device. CONFIG_ENV_OFFSET must be
3828 aligned to an erase block boundary.
3830 - CONFIG_ENV_OFFSET_REDUND (optional):
3832 This setting describes a second storage area of CONFIG_ENV_SIZE
3833 size used to hold a redundant copy of the environment data, so
3834 that there is a valid backup copy in case there is a power failure
3835 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
3836 aligned to an erase block boundary.
3838 - CONFIG_ENV_RANGE (optional):
3840 Specifies the length of the region in which the environment
3841 can be written. This should be a multiple of the NAND device's
3842 block size. Specifying a range with more erase blocks than
3843 are needed to hold CONFIG_ENV_SIZE allows bad blocks within
3844 the range to be avoided.
3846 - CONFIG_ENV_OFFSET_OOB (optional):
3848 Enables support for dynamically retrieving the offset of the
3849 environment from block zero's out-of-band data. The
3850 "nand env.oob" command can be used to record this offset.
3851 Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
3852 using CONFIG_ENV_OFFSET_OOB.
3854 - CONFIG_NAND_ENV_DST
3856 Defines address in RAM to which the nand_spl code should copy the
3857 environment. If redundant environment is used, it will be copied to
3858 CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
3860 - CONFIG_ENV_IS_IN_UBI:
3862 Define this if you have an UBI volume that you want to use for the
3863 environment. This has the benefit of wear-leveling the environment
3864 accesses, which is important on NAND.
3866 - CONFIG_ENV_UBI_PART:
3868 Define this to a string that is the mtd partition containing the UBI.
3870 - CONFIG_ENV_UBI_VOLUME:
3872 Define this to the name of the volume that you want to store the
3875 - CONFIG_ENV_UBI_VOLUME_REDUND:
3877 Define this to the name of another volume to store a second copy of
3878 the environment in. This will enable redundant environments in UBI.
3879 It is assumed that both volumes are in the same MTD partition.
3881 - CONFIG_UBI_SILENCE_MSG
3882 - CONFIG_UBIFS_SILENCE_MSG
3884 You will probably want to define these to avoid a really noisy system
3885 when storing the env in UBI.
3887 - CONFIG_ENV_IS_IN_MMC:
3889 Define this if you have an MMC device which you want to use for the
3892 - CONFIG_SYS_MMC_ENV_DEV:
3894 Specifies which MMC device the environment is stored in.
3896 - CONFIG_SYS_MMC_ENV_PART (optional):
3898 Specifies which MMC partition the environment is stored in. If not
3899 set, defaults to partition 0, the user area. Common values might be
3900 1 (first MMC boot partition), 2 (second MMC boot partition).
3902 - CONFIG_ENV_OFFSET:
3905 These two #defines specify the offset and size of the environment
3906 area within the specified MMC device.
3908 If offset is positive (the usual case), it is treated as relative to
3909 the start of the MMC partition. If offset is negative, it is treated
3910 as relative to the end of the MMC partition. This can be useful if
3911 your board may be fitted with different MMC devices, which have
3912 different sizes for the MMC partitions, and you always want the
3913 environment placed at the very end of the partition, to leave the
3914 maximum possible space before it, to store other data.
3916 These two values are in units of bytes, but must be aligned to an
3917 MMC sector boundary.
3919 - CONFIG_ENV_OFFSET_REDUND (optional):
3921 Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
3922 hold a redundant copy of the environment data. This provides a
3923 valid backup copy in case the other copy is corrupted, e.g. due
3924 to a power failure during a "saveenv" operation.
3926 This value may also be positive or negative; this is handled in the
3927 same way as CONFIG_ENV_OFFSET.
3929 This value is also in units of bytes, but must also be aligned to
3930 an MMC sector boundary.
3932 - CONFIG_ENV_SIZE_REDUND (optional):
3934 This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
3935 set. If this value is set, it must be set to the same value as
3938 - CONFIG_SYS_SPI_INIT_OFFSET
3940 Defines offset to the initial SPI buffer area in DPRAM. The
3941 area is used at an early stage (ROM part) if the environment
3942 is configured to reside in the SPI EEPROM: We need a 520 byte
3943 scratch DPRAM area. It is used between the two initialization
3944 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
3945 to be a good choice since it makes it far enough from the
3946 start of the data area as well as from the stack pointer.
3948 Please note that the environment is read-only until the monitor
3949 has been relocated to RAM and a RAM copy of the environment has been
3950 created; also, when using EEPROM you will have to use getenv_f()
3951 until then to read environment variables.
3953 The environment is protected by a CRC32 checksum. Before the monitor
3954 is relocated into RAM, as a result of a bad CRC you will be working
3955 with the compiled-in default environment - *silently*!!! [This is
3956 necessary, because the first environment variable we need is the
3957 "baudrate" setting for the console - if we have a bad CRC, we don't
3958 have any device yet where we could complain.]
3960 Note: once the monitor has been relocated, then it will complain if
3961 the default environment is used; a new CRC is computed as soon as you
3962 use the "saveenv" command to store a valid environment.
3964 - CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
3965 Echo the inverted Ethernet link state to the fault LED.
3967 Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
3968 also needs to be defined.
3970 - CONFIG_SYS_FAULT_MII_ADDR:
3971 MII address of the PHY to check for the Ethernet link state.
3973 - CONFIG_NS16550_MIN_FUNCTIONS:
3974 Define this if you desire to only have use of the NS16550_init
3975 and NS16550_putc functions for the serial driver located at
3976 drivers/serial/ns16550.c. This option is useful for saving
3977 space for already greatly restricted images, including but not
3978 limited to NAND_SPL configurations.
3980 - CONFIG_DISPLAY_BOARDINFO
3981 Display information about the board that U-Boot is running on
3982 when U-Boot starts up. The board function checkboard() is called
3985 - CONFIG_DISPLAY_BOARDINFO_LATE
3986 Similar to the previous option, but display this information
3987 later, once stdio is running and output goes to the LCD, if
3990 Low Level (hardware related) configuration options:
3991 ---------------------------------------------------
3993 - CONFIG_SYS_CACHELINE_SIZE:
3994 Cache Line Size of the CPU.
3996 - CONFIG_SYS_DEFAULT_IMMR:
3997 Default address of the IMMR after system reset.
3999 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
4000 and RPXsuper) to be able to adjust the position of
4001 the IMMR register after a reset.
4003 - CONFIG_SYS_CCSRBAR_DEFAULT:
4004 Default (power-on reset) physical address of CCSR on Freescale
4007 - CONFIG_SYS_CCSRBAR:
4008 Virtual address of CCSR. On a 32-bit build, this is typically
4009 the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
4011 CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
4012 for cross-platform code that uses that macro instead.
4014 - CONFIG_SYS_CCSRBAR_PHYS:
4015 Physical address of CCSR. CCSR can be relocated to a new
4016 physical address, if desired. In this case, this macro should
4017 be set to that address. Otherwise, it should be set to the
4018 same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR
4019 is typically relocated on 36-bit builds. It is recommended
4020 that this macro be defined via the _HIGH and _LOW macros:
4022 #define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
4023 * 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)
4025 - CONFIG_SYS_CCSRBAR_PHYS_HIGH:
4026 Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically
4027 either 0 (32-bit build) or 0xF (36-bit build). This macro is
4028 used in assembly code, so it must not contain typecasts or
4029 integer size suffixes (e.g. "ULL").
4031 - CONFIG_SYS_CCSRBAR_PHYS_LOW:
4032 Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is
4033 used in assembly code, so it must not contain typecasts or
4034 integer size suffixes (e.g. "ULL").
4036 - CONFIG_SYS_CCSR_DO_NOT_RELOCATE:
4037 If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
4038 forced to a value that ensures that CCSR is not relocated.
4040 - Floppy Disk Support:
4041 CONFIG_SYS_FDC_DRIVE_NUMBER
4043 the default drive number (default value 0)
4045 CONFIG_SYS_ISA_IO_STRIDE
4047 defines the spacing between FDC chipset registers
4050 CONFIG_SYS_ISA_IO_OFFSET
4052 defines the offset of register from address. It
4053 depends on which part of the data bus is connected to
4054 the FDC chipset. (default value 0)
4056 If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
4057 CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
4060 if CONFIG_SYS_FDC_HW_INIT is defined, then the function
4061 fdc_hw_init() is called at the beginning of the FDC
4062 setup. fdc_hw_init() must be provided by the board
4063 source code. It is used to make hardware dependant
4067 Most IDE controllers were designed to be connected with PCI
4068 interface. Only few of them were designed for AHB interface.
4069 When software is doing ATA command and data transfer to
4070 IDE devices through IDE-AHB controller, some additional
4071 registers accessing to these kind of IDE-AHB controller
4074 - CONFIG_SYS_IMMR: Physical address of the Internal Memory.
4075 DO NOT CHANGE unless you know exactly what you're
4076 doing! (11-4) [MPC8xx/82xx systems only]
4078 - CONFIG_SYS_INIT_RAM_ADDR:
4080 Start address of memory area that can be used for
4081 initial data and stack; please note that this must be
4082 writable memory that is working WITHOUT special
4083 initialization, i. e. you CANNOT use normal RAM which
4084 will become available only after programming the
4085 memory controller and running certain initialization
4088 U-Boot uses the following memory types:
4089 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
4090 - MPC824X: data cache
4091 - PPC4xx: data cache
4093 - CONFIG_SYS_GBL_DATA_OFFSET:
4095 Offset of the initial data structure in the memory
4096 area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
4097 CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
4098 data is located at the end of the available space
4099 (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
4100 CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
4101 below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
4102 CONFIG_SYS_GBL_DATA_OFFSET) downward.
4105 On the MPC824X (or other systems that use the data
4106 cache for initial memory) the address chosen for
4107 CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must
4108 point to an otherwise UNUSED address space between
4109 the top of RAM and the start of the PCI space.
4111 - CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
4113 - CONFIG_SYS_SYPCR: System Protection Control (11-9)
4115 - CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
4117 - CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
4119 - CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
4121 - CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
4123 - CONFIG_SYS_OR_TIMING_SDRAM:
4126 - CONFIG_SYS_MAMR_PTA:
4127 periodic timer for refresh
4129 - CONFIG_SYS_DER: Debug Event Register (37-47)
4131 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
4132 CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
4133 CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
4134 CONFIG_SYS_BR1_PRELIM:
4135 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
4137 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
4138 CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM,
4139 CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
4140 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
4142 - CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
4143 CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
4144 Machine Mode Register and Memory Periodic Timer
4145 Prescaler definitions (SDRAM timing)
4147 - CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
4148 enable I2C microcode relocation patch (MPC8xx);
4149 define relocation offset in DPRAM [DSP2]
4151 - CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
4152 enable SMC microcode relocation patch (MPC8xx);
4153 define relocation offset in DPRAM [SMC1]
4155 - CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
4156 enable SPI microcode relocation patch (MPC8xx);
4157 define relocation offset in DPRAM [SCC4]
4159 - CONFIG_SYS_USE_OSCCLK:
4160 Use OSCM clock mode on MBX8xx board. Be careful,
4161 wrong setting might damage your board. Read
4162 doc/README.MBX before setting this variable!
4164 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
4165 Offset of the bootmode word in DPRAM used by post
4166 (Power On Self Tests). This definition overrides
4167 #define'd default value in commproc.h resp.
4170 - CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
4171 CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
4172 CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
4173 CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
4174 CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
4175 CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
4176 CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
4177 CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
4178 Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
4180 - CONFIG_PCI_DISABLE_PCIE:
4181 Disable PCI-Express on systems where it is supported but not
4184 - CONFIG_PCI_ENUM_ONLY
4185 Only scan through and get the devices on the busses.
4186 Don't do any setup work, presumably because someone or
4187 something has already done it, and we don't need to do it
4188 a second time. Useful for platforms that are pre-booted
4189 by coreboot or similar.
4191 - CONFIG_PCI_INDIRECT_BRIDGE:
4192 Enable support for indirect PCI bridges.
4195 Chip has SRIO or not
4198 Board has SRIO 1 port available
4201 Board has SRIO 2 port available
4203 - CONFIG_SRIO_PCIE_BOOT_MASTER
4204 Board can support master function for Boot from SRIO and PCIE
4206 - CONFIG_SYS_SRIOn_MEM_VIRT:
4207 Virtual Address of SRIO port 'n' memory region
4209 - CONFIG_SYS_SRIOn_MEM_PHYS:
4210 Physical Address of SRIO port 'n' memory region
4212 - CONFIG_SYS_SRIOn_MEM_SIZE:
4213 Size of SRIO port 'n' memory region
4215 - CONFIG_SYS_NAND_BUSWIDTH_16BIT
4216 Defined to tell the NAND controller that the NAND chip is using
4218 Not all NAND drivers use this symbol.
4219 Example of drivers that use it:
4220 - drivers/mtd/nand/ndfc.c
4221 - drivers/mtd/nand/mxc_nand.c
4223 - CONFIG_SYS_NDFC_EBC0_CFG
4224 Sets the EBC0_CFG register for the NDFC. If not defined
4225 a default value will be used.
4228 Get DDR timing information from an I2C EEPROM. Common
4229 with pluggable memory modules such as SODIMMs
4232 I2C address of the SPD EEPROM
4234 - CONFIG_SYS_SPD_BUS_NUM
4235 If SPD EEPROM is on an I2C bus other than the first
4236 one, specify here. Note that the value must resolve
4237 to something your driver can deal with.
4239 - CONFIG_SYS_DDR_RAW_TIMING
4240 Get DDR timing information from other than SPD. Common with
4241 soldered DDR chips onboard without SPD. DDR raw timing
4242 parameters are extracted from datasheet and hard-coded into
4243 header files or board specific files.
4245 - CONFIG_FSL_DDR_INTERACTIVE
4246 Enable interactive DDR debugging. See doc/README.fsl-ddr.
4248 - CONFIG_SYS_83XX_DDR_USES_CS0
4249 Only for 83xx systems. If specified, then DDR should
4250 be configured using CS0 and CS1 instead of CS2 and CS3.
4252 - CONFIG_ETHER_ON_FEC[12]
4253 Define to enable FEC[12] on a 8xx series processor.
4255 - CONFIG_FEC[12]_PHY
4256 Define to the hardcoded PHY address which corresponds
4257 to the given FEC; i. e.
4258 #define CONFIG_FEC1_PHY 4
4259 means that the PHY with address 4 is connected to FEC1
4261 When set to -1, means to probe for first available.
4263 - CONFIG_FEC[12]_PHY_NORXERR
4264 The PHY does not have a RXERR line (RMII only).
4265 (so program the FEC to ignore it).
4268 Enable RMII mode for all FECs.
4269 Note that this is a global option, we can't
4270 have one FEC in standard MII mode and another in RMII mode.
4272 - CONFIG_CRC32_VERIFY
4273 Add a verify option to the crc32 command.
4276 => crc32 -v <address> <count> <crc32>
4278 Where address/count indicate a memory area
4279 and crc32 is the correct crc32 which the
4283 Add the "loopw" memory command. This only takes effect if
4284 the memory commands are activated globally (CONFIG_CMD_MEM).
4287 Add the "mdc" and "mwc" memory commands. These are cyclic
4292 This command will print 4 bytes (10,11,12,13) each 500 ms.
4294 => mwc.l 100 12345678 10
4295 This command will write 12345678 to address 100 all 10 ms.
4297 This only takes effect if the memory commands are activated
4298 globally (CONFIG_CMD_MEM).
4300 - CONFIG_SKIP_LOWLEVEL_INIT
4301 [ARM, NDS32, MIPS only] If this variable is defined, then certain
4302 low level initializations (like setting up the memory
4303 controller) are omitted and/or U-Boot does not
4304 relocate itself into RAM.
4306 Normally this variable MUST NOT be defined. The only
4307 exception is when U-Boot is loaded (to RAM) by some
4308 other boot loader or by a debugger which performs
4309 these initializations itself.
4312 Modifies the behaviour of start.S when compiling a loader
4313 that is executed before the actual U-Boot. E.g. when
4314 compiling a NAND SPL.
4317 Modifies the behaviour of start.S when compiling a loader
4318 that is executed after the SPL and before the actual U-Boot.
4319 It is loaded by the SPL.
4321 - CONFIG_SYS_MPC85XX_NO_RESETVEC
4322 Only for 85xx systems. If this variable is specified, the section
4323 .resetvec is not kept and the section .bootpg is placed in the
4324 previous 4k of the .text section.
4326 - CONFIG_ARCH_MAP_SYSMEM
4327 Generally U-Boot (and in particular the md command) uses
4328 effective address. It is therefore not necessary to regard
4329 U-Boot address as virtual addresses that need to be translated
4330 to physical addresses. However, sandbox requires this, since
4331 it maintains its own little RAM buffer which contains all
4332 addressable memory. This option causes some memory accesses
4333 to be mapped through map_sysmem() / unmap_sysmem().
4335 - CONFIG_USE_ARCH_MEMCPY
4336 CONFIG_USE_ARCH_MEMSET
4337 If these options are used a optimized version of memcpy/memset will
4338 be used if available. These functions may be faster under some
4339 conditions but may increase the binary size.
4341 - CONFIG_X86_RESET_VECTOR
4342 If defined, the x86 reset vector code is included. This is not
4343 needed when U-Boot is running from Coreboot.
4346 Defines the MPU clock speed (in MHz).
4348 NOTE : currently only supported on AM335x platforms.
4350 Freescale QE/FMAN Firmware Support:
4351 -----------------------------------
4353 The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
4354 loading of "firmware", which is encoded in the QE firmware binary format.
4355 This firmware often needs to be loaded during U-Boot booting, so macros
4356 are used to identify the storage device (NOR flash, SPI, etc) and the address
4359 - CONFIG_SYS_QE_FMAN_FW_ADDR
4360 The address in the storage device where the firmware is located. The
4361 meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
4364 - CONFIG_SYS_QE_FMAN_FW_LENGTH
4365 The maximum possible size of the firmware. The firmware binary format
4366 has a field that specifies the actual size of the firmware, but it
4367 might not be possible to read any part of the firmware unless some
4368 local storage is allocated to hold the entire firmware first.
4370 - CONFIG_SYS_QE_FMAN_FW_IN_NOR
4371 Specifies that QE/FMAN firmware is located in NOR flash, mapped as
4372 normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the
4373 virtual address in NOR flash.
4375 - CONFIG_SYS_QE_FMAN_FW_IN_NAND
4376 Specifies that QE/FMAN firmware is located in NAND flash.
4377 CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
4379 - CONFIG_SYS_QE_FMAN_FW_IN_MMC
4380 Specifies that QE/FMAN firmware is located on the primary SD/MMC
4381 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
4383 - CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
4384 Specifies that QE/FMAN firmware is located on the primary SPI
4385 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
4387 - CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
4388 Specifies that QE/FMAN firmware is located in the remote (master)
4389 memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
4390 can be mapped from slave TLB->slave LAW->slave SRIO or PCIE outbound
4391 window->master inbound window->master LAW->the ucode address in
4392 master's memory space.
4394 Building the Software:
4395 ======================
4397 Building U-Boot has been tested in several native build environments
4398 and in many different cross environments. Of course we cannot support
4399 all possibly existing versions of cross development tools in all
4400 (potentially obsolete) versions. In case of tool chain problems we
4401 recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
4402 which is extensively used to build and test U-Boot.
4404 If you are not using a native environment, it is assumed that you
4405 have GNU cross compiling tools available in your path. In this case,
4406 you must set the environment variable CROSS_COMPILE in your shell.
4407 Note that no changes to the Makefile or any other source files are
4408 necessary. For example using the ELDK on a 4xx CPU, please enter:
4410 $ CROSS_COMPILE=ppc_4xx-
4411 $ export CROSS_COMPILE
4413 Note: If you wish to generate Windows versions of the utilities in
4414 the tools directory you can use the MinGW toolchain
4415 (http://www.mingw.org). Set your HOST tools to the MinGW
4416 toolchain and execute 'make tools'. For example:
4418 $ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
4420 Binaries such as tools/mkimage.exe will be created which can
4421 be executed on computers running Windows.
4423 U-Boot is intended to be simple to build. After installing the
4424 sources you must configure U-Boot for one specific board type. This
4429 where "NAME_config" is the name of one of the existing configu-
4430 rations; see boards.cfg for supported names.
4432 Note: for some board special configuration names may exist; check if
4433 additional information is available from the board vendor; for
4434 instance, the TQM823L systems are available without (standard)
4435 or with LCD support. You can select such additional "features"
4436 when choosing the configuration, i. e.
4439 - will configure for a plain TQM823L, i. e. no LCD support
4441 make TQM823L_LCD_config
4442 - will configure for a TQM823L with U-Boot console on LCD
4447 Finally, type "make all", and you should get some working U-Boot
4448 images ready for download to / installation on your system:
4450 - "u-boot.bin" is a raw binary image
4451 - "u-boot" is an image in ELF binary format
4452 - "u-boot.srec" is in Motorola S-Record format
4454 By default the build is performed locally and the objects are saved
4455 in the source directory. One of the two methods can be used to change
4456 this behavior and build U-Boot to some external directory:
4458 1. Add O= to the make command line invocations:
4460 make O=/tmp/build distclean
4461 make O=/tmp/build NAME_config
4462 make O=/tmp/build all
4464 2. Set environment variable BUILD_DIR to point to the desired location:
4466 export BUILD_DIR=/tmp/build
4471 Note that the command line "O=" setting overrides the BUILD_DIR environment
4475 Please be aware that the Makefiles assume you are using GNU make, so
4476 for instance on NetBSD you might need to use "gmake" instead of
4480 If the system board that you have is not listed, then you will need
4481 to port U-Boot to your hardware platform. To do this, follow these
4484 1. Add a new configuration option for your board to the toplevel
4485 "boards.cfg" file, using the existing entries as examples.
4486 Follow the instructions there to keep the boards in order.
4487 2. Create a new directory to hold your board specific code. Add any
4488 files you need. In your board directory, you will need at least
4489 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
4490 3. Create a new configuration file "include/configs/<board>.h" for
4492 3. If you're porting U-Boot to a new CPU, then also create a new
4493 directory to hold your CPU specific code. Add any files you need.
4494 4. Run "make <board>_config" with your new name.
4495 5. Type "make", and you should get a working "u-boot.srec" file
4496 to be installed on your target system.
4497 6. Debug and solve any problems that might arise.
4498 [Of course, this last step is much harder than it sounds.]
4501 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
4502 ==============================================================
4504 If you have modified U-Boot sources (for instance added a new board
4505 or support for new devices, a new CPU, etc.) you are expected to
4506 provide feedback to the other developers. The feedback normally takes
4507 the form of a "patch", i. e. a context diff against a certain (latest
4508 official or latest in the git repository) version of U-Boot sources.
4510 But before you submit such a patch, please verify that your modifi-
4511 cation did not break existing code. At least make sure that *ALL* of
4512 the supported boards compile WITHOUT ANY compiler warnings. To do so,
4513 just run the "MAKEALL" script, which will configure and build U-Boot
4514 for ALL supported system. Be warned, this will take a while. You can
4515 select which (cross) compiler to use by passing a `CROSS_COMPILE'
4516 environment variable to the script, i. e. to use the ELDK cross tools
4519 CROSS_COMPILE=ppc_8xx- MAKEALL
4521 or to build on a native PowerPC system you can type
4523 CROSS_COMPILE=' ' MAKEALL
4525 When using the MAKEALL script, the default behaviour is to build
4526 U-Boot in the source directory. This location can be changed by
4527 setting the BUILD_DIR environment variable. Also, for each target
4528 built, the MAKEALL script saves two log files (<target>.ERR and
4529 <target>.MAKEALL) in the <source dir>/LOG directory. This default
4530 location can be changed by setting the MAKEALL_LOGDIR environment
4531 variable. For example:
4533 export BUILD_DIR=/tmp/build
4534 export MAKEALL_LOGDIR=/tmp/log
4535 CROSS_COMPILE=ppc_8xx- MAKEALL
4537 With the above settings build objects are saved in the /tmp/build,
4538 log files are saved in the /tmp/log and the source tree remains clean
4539 during the whole build process.
4542 See also "U-Boot Porting Guide" below.
4545 Monitor Commands - Overview:
4546 ============================
4548 go - start application at address 'addr'
4549 run - run commands in an environment variable
4550 bootm - boot application image from memory
4551 bootp - boot image via network using BootP/TFTP protocol
4552 bootz - boot zImage from memory
4553 tftpboot- boot image via network using TFTP protocol
4554 and env variables "ipaddr" and "serverip"
4555 (and eventually "gatewayip")
4556 tftpput - upload a file via network using TFTP protocol
4557 rarpboot- boot image via network using RARP/TFTP protocol
4558 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
4559 loads - load S-Record file over serial line
4560 loadb - load binary file over serial line (kermit mode)
4562 mm - memory modify (auto-incrementing)
4563 nm - memory modify (constant address)
4564 mw - memory write (fill)
4566 cmp - memory compare
4567 crc32 - checksum calculation
4568 i2c - I2C sub-system
4569 sspi - SPI utility commands
4570 base - print or set address offset
4571 printenv- print environment variables
4572 setenv - set environment variables
4573 saveenv - save environment variables to persistent storage
4574 protect - enable or disable FLASH write protection
4575 erase - erase FLASH memory
4576 flinfo - print FLASH memory information
4577 nand - NAND memory operations (see doc/README.nand)
4578 bdinfo - print Board Info structure
4579 iminfo - print header information for application image
4580 coninfo - print console devices and informations
4581 ide - IDE sub-system
4582 loop - infinite loop on address range
4583 loopw - infinite write loop on address range
4584 mtest - simple RAM test
4585 icache - enable or disable instruction cache
4586 dcache - enable or disable data cache
4587 reset - Perform RESET of the CPU
4588 echo - echo args to console
4589 version - print monitor version
4590 help - print online help
4591 ? - alias for 'help'
4594 Monitor Commands - Detailed Description:
4595 ========================================
4599 For now: just type "help <command>".
4602 Environment Variables:
4603 ======================
4605 U-Boot supports user configuration using Environment Variables which
4606 can be made persistent by saving to Flash memory.
4608 Environment Variables are set using "setenv", printed using
4609 "printenv", and saved to Flash using "saveenv". Using "setenv"
4610 without a value can be used to delete a variable from the
4611 environment. As long as you don't save the environment you are
4612 working with an in-memory copy. In case the Flash area containing the
4613 environment is erased by accident, a default environment is provided.
4615 Some configuration options can be set using Environment Variables.
4617 List of environment variables (most likely not complete):
4619 baudrate - see CONFIG_BAUDRATE
4621 bootdelay - see CONFIG_BOOTDELAY
4623 bootcmd - see CONFIG_BOOTCOMMAND
4625 bootargs - Boot arguments when booting an RTOS image
4627 bootfile - Name of the image to load with TFTP
4629 bootm_low - Memory range available for image processing in the bootm
4630 command can be restricted. This variable is given as
4631 a hexadecimal number and defines lowest address allowed
4632 for use by the bootm command. See also "bootm_size"
4633 environment variable. Address defined by "bootm_low" is
4634 also the base of the initial memory mapping for the Linux
4635 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
4638 bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
4639 This variable is given as a hexadecimal number and it
4640 defines the size of the memory region starting at base
4641 address bootm_low that is accessible by the Linux kernel
4642 during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
4643 as the default value if it is defined, and bootm_size is
4646 bootm_size - Memory range available for image processing in the bootm
4647 command can be restricted. This variable is given as
4648 a hexadecimal number and defines the size of the region
4649 allowed for use by the bootm command. See also "bootm_low"
4650 environment variable.
4652 updatefile - Location of the software update file on a TFTP server, used
4653 by the automatic software update feature. Please refer to
4654 documentation in doc/README.update for more details.
4656 autoload - if set to "no" (any string beginning with 'n'),
4657 "bootp" will just load perform a lookup of the
4658 configuration from the BOOTP server, but not try to
4659 load any image using TFTP
4661 autostart - if set to "yes", an image loaded using the "bootp",
4662 "rarpboot", "tftpboot" or "diskboot" commands will
4663 be automatically started (by internally calling
4666 If set to "no", a standalone image passed to the
4667 "bootm" command will be copied to the load address
4668 (and eventually uncompressed), but NOT be started.
4669 This can be used to load and uncompress arbitrary
4672 fdt_high - if set this restricts the maximum address that the
4673 flattened device tree will be copied into upon boot.
4674 For example, if you have a system with 1 GB memory
4675 at physical address 0x10000000, while Linux kernel
4676 only recognizes the first 704 MB as low memory, you
4677 may need to set fdt_high as 0x3C000000 to have the
4678 device tree blob be copied to the maximum address
4679 of the 704 MB low memory, so that Linux kernel can
4680 access it during the boot procedure.
4682 If this is set to the special value 0xFFFFFFFF then
4683 the fdt will not be copied at all on boot. For this
4684 to work it must reside in writable memory, have
4685 sufficient padding on the end of it for u-boot to
4686 add the information it needs into it, and the memory
4687 must be accessible by the kernel.
4689 fdtcontroladdr- if set this is the address of the control flattened
4690 device tree used by U-Boot when CONFIG_OF_CONTROL is
4693 i2cfast - (PPC405GP|PPC405EP only)
4694 if set to 'y' configures Linux I2C driver for fast
4695 mode (400kHZ). This environment variable is used in
4696 initialization code. So, for changes to be effective
4697 it must be saved and board must be reset.
4699 initrd_high - restrict positioning of initrd images:
4700 If this variable is not set, initrd images will be
4701 copied to the highest possible address in RAM; this
4702 is usually what you want since it allows for
4703 maximum initrd size. If for some reason you want to
4704 make sure that the initrd image is loaded below the
4705 CONFIG_SYS_BOOTMAPSZ limit, you can set this environment
4706 variable to a value of "no" or "off" or "0".
4707 Alternatively, you can set it to a maximum upper
4708 address to use (U-Boot will still check that it
4709 does not overwrite the U-Boot stack and data).
4711 For instance, when you have a system with 16 MB
4712 RAM, and want to reserve 4 MB from use by Linux,
4713 you can do this by adding "mem=12M" to the value of
4714 the "bootargs" variable. However, now you must make
4715 sure that the initrd image is placed in the first
4716 12 MB as well - this can be done with
4718 setenv initrd_high 00c00000
4720 If you set initrd_high to 0xFFFFFFFF, this is an
4721 indication to U-Boot that all addresses are legal
4722 for the Linux kernel, including addresses in flash
4723 memory. In this case U-Boot will NOT COPY the
4724 ramdisk at all. This may be useful to reduce the
4725 boot time on your system, but requires that this
4726 feature is supported by your Linux kernel.
4728 ipaddr - IP address; needed for tftpboot command
4730 loadaddr - Default load address for commands like "bootp",
4731 "rarpboot", "tftpboot", "loadb" or "diskboot"
4733 loads_echo - see CONFIG_LOADS_ECHO
4735 serverip - TFTP server IP address; needed for tftpboot command
4737 bootretry - see CONFIG_BOOT_RETRY_TIME
4739 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
4741 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
4743 ethprime - controls which interface is used first.
4745 ethact - controls which interface is currently active.
4746 For example you can do the following
4748 => setenv ethact FEC
4749 => ping 192.168.0.1 # traffic sent on FEC
4750 => setenv ethact SCC
4751 => ping 10.0.0.1 # traffic sent on SCC
4753 ethrotate - When set to "no" U-Boot does not go through all
4754 available network interfaces.
4755 It just stays at the currently selected interface.
4757 netretry - When set to "no" each network operation will
4758 either succeed or fail without retrying.
4759 When set to "once" the network operation will
4760 fail when all the available network interfaces
4761 are tried once without success.
4762 Useful on scripts which control the retry operation
4765 npe_ucode - set load address for the NPE microcode
4767 silent_linux - If set then linux will be told to boot silently, by
4768 changing the console to be empty. If "yes" it will be
4769 made silent. If "no" it will not be made silent. If
4770 unset, then it will be made silent if the U-Boot console
4773 tftpsrcport - If this is set, the value is used for TFTP's
4776 tftpdstport - If this is set, the value is used for TFTP's UDP
4777 destination port instead of the Well Know Port 69.
4779 tftpblocksize - Block size to use for TFTP transfers; if not set,
4780 we use the TFTP server's default block size
4782 tftptimeout - Retransmission timeout for TFTP packets (in milli-
4783 seconds, minimum value is 1000 = 1 second). Defines
4784 when a packet is considered to be lost so it has to
4785 be retransmitted. The default is 5000 = 5 seconds.
4786 Lowering this value may make downloads succeed
4787 faster in networks with high packet loss rates or
4788 with unreliable TFTP servers.
4790 vlan - When set to a value < 4095 the traffic over
4791 Ethernet is encapsulated/received over 802.1q
4794 The following image location variables contain the location of images
4795 used in booting. The "Image" column gives the role of the image and is
4796 not an environment variable name. The other columns are environment
4797 variable names. "File Name" gives the name of the file on a TFTP
4798 server, "RAM Address" gives the location in RAM the image will be
4799 loaded to, and "Flash Location" gives the image's address in NOR
4800 flash or offset in NAND flash.
4802 *Note* - these variables don't have to be defined for all boards, some
4803 boards currenlty use other variables for these purposes, and some
4804 boards use these variables for other purposes.
4806 Image File Name RAM Address Flash Location
4807 ----- --------- ----------- --------------
4808 u-boot u-boot u-boot_addr_r u-boot_addr
4809 Linux kernel bootfile kernel_addr_r kernel_addr
4810 device tree blob fdtfile fdt_addr_r fdt_addr
4811 ramdisk ramdiskfile ramdisk_addr_r ramdisk_addr
4813 The following environment variables may be used and automatically
4814 updated by the network boot commands ("bootp" and "rarpboot"),
4815 depending the information provided by your boot server:
4817 bootfile - see above
4818 dnsip - IP address of your Domain Name Server
4819 dnsip2 - IP address of your secondary Domain Name Server
4820 gatewayip - IP address of the Gateway (Router) to use
4821 hostname - Target hostname
4823 netmask - Subnet Mask
4824 rootpath - Pathname of the root filesystem on the NFS server
4825 serverip - see above
4828 There are two special Environment Variables:
4830 serial# - contains hardware identification information such
4831 as type string and/or serial number
4832 ethaddr - Ethernet address
4834 These variables can be set only once (usually during manufacturing of
4835 the board). U-Boot refuses to delete or overwrite these variables
4836 once they have been set once.
4839 Further special Environment Variables:
4841 ver - Contains the U-Boot version string as printed
4842 with the "version" command. This variable is
4843 readonly (see CONFIG_VERSION_VARIABLE).
4846 Please note that changes to some configuration parameters may take
4847 only effect after the next boot (yes, that's just like Windoze :-).
4850 Callback functions for environment variables:
4851 ---------------------------------------------
4853 For some environment variables, the behavior of u-boot needs to change
4854 when their values are changed. This functionailty allows functions to
4855 be associated with arbitrary variables. On creation, overwrite, or
4856 deletion, the callback will provide the opportunity for some side
4857 effect to happen or for the change to be rejected.
4859 The callbacks are named and associated with a function using the
4860 U_BOOT_ENV_CALLBACK macro in your board or driver code.
4862 These callbacks are associated with variables in one of two ways. The
4863 static list can be added to by defining CONFIG_ENV_CALLBACK_LIST_STATIC
4864 in the board configuration to a string that defines a list of
4865 associations. The list must be in the following format:
4867 entry = variable_name[:callback_name]
4870 If the callback name is not specified, then the callback is deleted.
4871 Spaces are also allowed anywhere in the list.
4873 Callbacks can also be associated by defining the ".callbacks" variable
4874 with the same list format above. Any association in ".callbacks" will
4875 override any association in the static list. You can define
4876 CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the
4877 ".callbacks" envirnoment variable in the default or embedded environment.
4880 Command Line Parsing:
4881 =====================
4883 There are two different command line parsers available with U-Boot:
4884 the old "simple" one, and the much more powerful "hush" shell:
4886 Old, simple command line parser:
4887 --------------------------------
4889 - supports environment variables (through setenv / saveenv commands)
4890 - several commands on one line, separated by ';'
4891 - variable substitution using "... ${name} ..." syntax
4892 - special characters ('$', ';') can be escaped by prefixing with '\',
4894 setenv bootcmd bootm \${address}
4895 - You can also escape text by enclosing in single apostrophes, for example:
4896 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
4901 - similar to Bourne shell, with control structures like
4902 if...then...else...fi, for...do...done; while...do...done,
4903 until...do...done, ...
4904 - supports environment ("global") variables (through setenv / saveenv
4905 commands) and local shell variables (through standard shell syntax
4906 "name=value"); only environment variables can be used with "run"
4912 (1) If a command line (or an environment variable executed by a "run"
4913 command) contains several commands separated by semicolon, and
4914 one of these commands fails, then the remaining commands will be
4917 (2) If you execute several variables with one call to run (i. e.
4918 calling run with a list of variables as arguments), any failing
4919 command will cause "run" to terminate, i. e. the remaining
4920 variables are not executed.
4922 Note for Redundant Ethernet Interfaces:
4923 =======================================
4925 Some boards come with redundant Ethernet interfaces; U-Boot supports
4926 such configurations and is capable of automatic selection of a
4927 "working" interface when needed. MAC assignment works as follows:
4929 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
4930 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
4931 "eth1addr" (=>eth1), "eth2addr", ...
4933 If the network interface stores some valid MAC address (for instance
4934 in SROM), this is used as default address if there is NO correspon-
4935 ding setting in the environment; if the corresponding environment
4936 variable is set, this overrides the settings in the card; that means:
4938 o If the SROM has a valid MAC address, and there is no address in the
4939 environment, the SROM's address is used.
4941 o If there is no valid address in the SROM, and a definition in the
4942 environment exists, then the value from the environment variable is
4945 o If both the SROM and the environment contain a MAC address, and
4946 both addresses are the same, this MAC address is used.
4948 o If both the SROM and the environment contain a MAC address, and the
4949 addresses differ, the value from the environment is used and a
4952 o If neither SROM nor the environment contain a MAC address, an error
4955 If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
4956 will be programmed into hardware as part of the initialization process. This
4957 may be skipped by setting the appropriate 'ethmacskip' environment variable.
4958 The naming convention is as follows:
4959 "ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
4964 U-Boot is capable of booting (and performing other auxiliary operations on)
4965 images in two formats:
4967 New uImage format (FIT)
4968 -----------------------
4970 Flexible and powerful format based on Flattened Image Tree -- FIT (similar
4971 to Flattened Device Tree). It allows the use of images with multiple
4972 components (several kernels, ramdisks, etc.), with contents protected by
4973 SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
4979 Old image format is based on binary files which can be basically anything,
4980 preceded by a special header; see the definitions in include/image.h for
4981 details; basically, the header defines the following image properties:
4983 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
4984 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
4985 LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
4986 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
4988 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
4989 IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
4990 Currently supported: ARM, AVR32, Intel x86, MIPS, NDS32, Nios II, PowerPC).
4991 * Compression Type (uncompressed, gzip, bzip2)
4997 The header is marked by a special Magic Number, and both the header
4998 and the data portions of the image are secured against corruption by
5005 Although U-Boot should support any OS or standalone application
5006 easily, the main focus has always been on Linux during the design of
5009 U-Boot includes many features that so far have been part of some
5010 special "boot loader" code within the Linux kernel. Also, any
5011 "initrd" images to be used are no longer part of one big Linux image;
5012 instead, kernel and "initrd" are separate images. This implementation
5013 serves several purposes:
5015 - the same features can be used for other OS or standalone
5016 applications (for instance: using compressed images to reduce the
5017 Flash memory footprint)
5019 - it becomes much easier to port new Linux kernel versions because
5020 lots of low-level, hardware dependent stuff are done by U-Boot
5022 - the same Linux kernel image can now be used with different "initrd"
5023 images; of course this also means that different kernel images can
5024 be run with the same "initrd". This makes testing easier (you don't
5025 have to build a new "zImage.initrd" Linux image when you just
5026 change a file in your "initrd"). Also, a field-upgrade of the
5027 software is easier now.
5033 Porting Linux to U-Boot based systems:
5034 ---------------------------------------
5036 U-Boot cannot save you from doing all the necessary modifications to
5037 configure the Linux device drivers for use with your target hardware
5038 (no, we don't intend to provide a full virtual machine interface to
5041 But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
5043 Just make sure your machine specific header file (for instance
5044 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
5045 Information structure as we define in include/asm-<arch>/u-boot.h,
5046 and make sure that your definition of IMAP_ADDR uses the same value
5047 as your U-Boot configuration in CONFIG_SYS_IMMR.
5050 Configuring the Linux kernel:
5051 -----------------------------
5053 No specific requirements for U-Boot. Make sure you have some root
5054 device (initial ramdisk, NFS) for your target system.
5057 Building a Linux Image:
5058 -----------------------
5060 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
5061 not used. If you use recent kernel source, a new build target
5062 "uImage" will exist which automatically builds an image usable by
5063 U-Boot. Most older kernels also have support for a "pImage" target,
5064 which was introduced for our predecessor project PPCBoot and uses a
5065 100% compatible format.
5074 The "uImage" build target uses a special tool (in 'tools/mkimage') to
5075 encapsulate a compressed Linux kernel image with header information,
5076 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
5078 * build a standard "vmlinux" kernel image (in ELF binary format):
5080 * convert the kernel into a raw binary image:
5082 ${CROSS_COMPILE}-objcopy -O binary \
5083 -R .note -R .comment \
5084 -S vmlinux linux.bin
5086 * compress the binary image:
5090 * package compressed binary image for U-Boot:
5092 mkimage -A ppc -O linux -T kernel -C gzip \
5093 -a 0 -e 0 -n "Linux Kernel Image" \
5094 -d linux.bin.gz uImage
5097 The "mkimage" tool can also be used to create ramdisk images for use
5098 with U-Boot, either separated from the Linux kernel image, or
5099 combined into one file. "mkimage" encapsulates the images with a 64
5100 byte header containing information about target architecture,
5101 operating system, image type, compression method, entry points, time
5102 stamp, CRC32 checksums, etc.
5104 "mkimage" can be called in two ways: to verify existing images and
5105 print the header information, or to build new images.
5107 In the first form (with "-l" option) mkimage lists the information
5108 contained in the header of an existing U-Boot image; this includes
5109 checksum verification:
5111 tools/mkimage -l image
5112 -l ==> list image header information
5114 The second form (with "-d" option) is used to build a U-Boot image
5115 from a "data file" which is used as image payload:
5117 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
5118 -n name -d data_file image
5119 -A ==> set architecture to 'arch'
5120 -O ==> set operating system to 'os'
5121 -T ==> set image type to 'type'
5122 -C ==> set compression type 'comp'
5123 -a ==> set load address to 'addr' (hex)
5124 -e ==> set entry point to 'ep' (hex)
5125 -n ==> set image name to 'name'
5126 -d ==> use image data from 'datafile'
5128 Right now, all Linux kernels for PowerPC systems use the same load
5129 address (0x00000000), but the entry point address depends on the
5132 - 2.2.x kernels have the entry point at 0x0000000C,
5133 - 2.3.x and later kernels have the entry point at 0x00000000.
5135 So a typical call to build a U-Boot image would read:
5137 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
5138 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
5139 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
5140 > examples/uImage.TQM850L
5141 Image Name: 2.4.4 kernel for TQM850L
5142 Created: Wed Jul 19 02:34:59 2000
5143 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5144 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
5145 Load Address: 0x00000000
5146 Entry Point: 0x00000000
5148 To verify the contents of the image (or check for corruption):
5150 -> tools/mkimage -l examples/uImage.TQM850L
5151 Image Name: 2.4.4 kernel for TQM850L
5152 Created: Wed Jul 19 02:34:59 2000
5153 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5154 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
5155 Load Address: 0x00000000
5156 Entry Point: 0x00000000
5158 NOTE: for embedded systems where boot time is critical you can trade
5159 speed for memory and install an UNCOMPRESSED image instead: this
5160 needs more space in Flash, but boots much faster since it does not
5161 need to be uncompressed:
5163 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
5164 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
5165 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
5166 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
5167 > examples/uImage.TQM850L-uncompressed
5168 Image Name: 2.4.4 kernel for TQM850L
5169 Created: Wed Jul 19 02:34:59 2000
5170 Image Type: PowerPC Linux Kernel Image (uncompressed)
5171 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
5172 Load Address: 0x00000000
5173 Entry Point: 0x00000000
5176 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
5177 when your kernel is intended to use an initial ramdisk:
5179 -> tools/mkimage -n 'Simple Ramdisk Image' \
5180 > -A ppc -O linux -T ramdisk -C gzip \
5181 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
5182 Image Name: Simple Ramdisk Image
5183 Created: Wed Jan 12 14:01:50 2000
5184 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5185 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
5186 Load Address: 0x00000000
5187 Entry Point: 0x00000000
5190 Installing a Linux Image:
5191 -------------------------
5193 To downloading a U-Boot image over the serial (console) interface,
5194 you must convert the image to S-Record format:
5196 objcopy -I binary -O srec examples/image examples/image.srec
5198 The 'objcopy' does not understand the information in the U-Boot
5199 image header, so the resulting S-Record file will be relative to
5200 address 0x00000000. To load it to a given address, you need to
5201 specify the target address as 'offset' parameter with the 'loads'
5204 Example: install the image to address 0x40100000 (which on the
5205 TQM8xxL is in the first Flash bank):
5207 => erase 40100000 401FFFFF
5213 ## Ready for S-Record download ...
5214 ~>examples/image.srec
5215 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
5217 15989 15990 15991 15992
5218 [file transfer complete]
5220 ## Start Addr = 0x00000000
5223 You can check the success of the download using the 'iminfo' command;
5224 this includes a checksum verification so you can be sure no data
5225 corruption happened:
5229 ## Checking Image at 40100000 ...
5230 Image Name: 2.2.13 for initrd on TQM850L
5231 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5232 Data Size: 335725 Bytes = 327 kB = 0 MB
5233 Load Address: 00000000
5234 Entry Point: 0000000c
5235 Verifying Checksum ... OK
5241 The "bootm" command is used to boot an application that is stored in
5242 memory (RAM or Flash). In case of a Linux kernel image, the contents
5243 of the "bootargs" environment variable is passed to the kernel as
5244 parameters. You can check and modify this variable using the
5245 "printenv" and "setenv" commands:
5248 => printenv bootargs
5249 bootargs=root=/dev/ram
5251 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5253 => printenv bootargs
5254 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5257 ## Booting Linux kernel at 40020000 ...
5258 Image Name: 2.2.13 for NFS on TQM850L
5259 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5260 Data Size: 381681 Bytes = 372 kB = 0 MB
5261 Load Address: 00000000
5262 Entry Point: 0000000c
5263 Verifying Checksum ... OK
5264 Uncompressing Kernel Image ... OK
5265 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
5266 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5267 time_init: decrementer frequency = 187500000/60
5268 Calibrating delay loop... 49.77 BogoMIPS
5269 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
5272 If you want to boot a Linux kernel with initial RAM disk, you pass
5273 the memory addresses of both the kernel and the initrd image (PPBCOOT
5274 format!) to the "bootm" command:
5276 => imi 40100000 40200000
5278 ## Checking Image at 40100000 ...
5279 Image Name: 2.2.13 for initrd on TQM850L
5280 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5281 Data Size: 335725 Bytes = 327 kB = 0 MB
5282 Load Address: 00000000
5283 Entry Point: 0000000c
5284 Verifying Checksum ... OK
5286 ## Checking Image at 40200000 ...
5287 Image Name: Simple Ramdisk Image
5288 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5289 Data Size: 566530 Bytes = 553 kB = 0 MB
5290 Load Address: 00000000
5291 Entry Point: 00000000
5292 Verifying Checksum ... OK
5294 => bootm 40100000 40200000
5295 ## Booting Linux kernel at 40100000 ...
5296 Image Name: 2.2.13 for initrd on TQM850L
5297 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5298 Data Size: 335725 Bytes = 327 kB = 0 MB
5299 Load Address: 00000000
5300 Entry Point: 0000000c
5301 Verifying Checksum ... OK
5302 Uncompressing Kernel Image ... OK
5303 ## Loading RAMDisk Image at 40200000 ...
5304 Image Name: Simple Ramdisk Image
5305 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5306 Data Size: 566530 Bytes = 553 kB = 0 MB
5307 Load Address: 00000000
5308 Entry Point: 00000000
5309 Verifying Checksum ... OK
5310 Loading Ramdisk ... OK
5311 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
5312 Boot arguments: root=/dev/ram
5313 time_init: decrementer frequency = 187500000/60
5314 Calibrating delay loop... 49.77 BogoMIPS
5316 RAMDISK: Compressed image found at block 0
5317 VFS: Mounted root (ext2 filesystem).
5321 Boot Linux and pass a flat device tree:
5324 First, U-Boot must be compiled with the appropriate defines. See the section
5325 titled "Linux Kernel Interface" above for a more in depth explanation. The
5326 following is an example of how to start a kernel and pass an updated
5332 oft=oftrees/mpc8540ads.dtb
5333 => tftp $oftaddr $oft
5334 Speed: 1000, full duplex
5336 TFTP from server 192.168.1.1; our IP address is 192.168.1.101
5337 Filename 'oftrees/mpc8540ads.dtb'.
5338 Load address: 0x300000
5341 Bytes transferred = 4106 (100a hex)
5342 => tftp $loadaddr $bootfile
5343 Speed: 1000, full duplex
5345 TFTP from server 192.168.1.1; our IP address is 192.168.1.2
5347 Load address: 0x200000
5348 Loading:############
5350 Bytes transferred = 1029407 (fb51f hex)
5355 => bootm $loadaddr - $oftaddr
5356 ## Booting image at 00200000 ...
5357 Image Name: Linux-2.6.17-dirty
5358 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5359 Data Size: 1029343 Bytes = 1005.2 kB
5360 Load Address: 00000000
5361 Entry Point: 00000000
5362 Verifying Checksum ... OK
5363 Uncompressing Kernel Image ... OK
5364 Booting using flat device tree at 0x300000
5365 Using MPC85xx ADS machine description
5366 Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
5370 More About U-Boot Image Types:
5371 ------------------------------
5373 U-Boot supports the following image types:
5375 "Standalone Programs" are directly runnable in the environment
5376 provided by U-Boot; it is expected that (if they behave
5377 well) you can continue to work in U-Boot after return from
5378 the Standalone Program.
5379 "OS Kernel Images" are usually images of some Embedded OS which
5380 will take over control completely. Usually these programs
5381 will install their own set of exception handlers, device
5382 drivers, set up the MMU, etc. - this means, that you cannot
5383 expect to re-enter U-Boot except by resetting the CPU.
5384 "RAMDisk Images" are more or less just data blocks, and their
5385 parameters (address, size) are passed to an OS kernel that is
5387 "Multi-File Images" contain several images, typically an OS
5388 (Linux) kernel image and one or more data images like
5389 RAMDisks. This construct is useful for instance when you want
5390 to boot over the network using BOOTP etc., where the boot
5391 server provides just a single image file, but you want to get
5392 for instance an OS kernel and a RAMDisk image.
5394 "Multi-File Images" start with a list of image sizes, each
5395 image size (in bytes) specified by an "uint32_t" in network
5396 byte order. This list is terminated by an "(uint32_t)0".
5397 Immediately after the terminating 0 follow the images, one by
5398 one, all aligned on "uint32_t" boundaries (size rounded up to
5399 a multiple of 4 bytes).
5401 "Firmware Images" are binary images containing firmware (like
5402 U-Boot or FPGA images) which usually will be programmed to
5405 "Script files" are command sequences that will be executed by
5406 U-Boot's command interpreter; this feature is especially
5407 useful when you configure U-Boot to use a real shell (hush)
5408 as command interpreter.
5410 Booting the Linux zImage:
5411 -------------------------
5413 On some platforms, it's possible to boot Linux zImage. This is done
5414 using the "bootz" command. The syntax of "bootz" command is the same
5415 as the syntax of "bootm" command.
5417 Note, defining the CONFIG_SUPPORT_RAW_INITRD allows user to supply
5418 kernel with raw initrd images. The syntax is slightly different, the
5419 address of the initrd must be augmented by it's size, in the following
5420 format: "<initrd addres>:<initrd size>".
5426 One of the features of U-Boot is that you can dynamically load and
5427 run "standalone" applications, which can use some resources of
5428 U-Boot like console I/O functions or interrupt services.
5430 Two simple examples are included with the sources:
5435 'examples/hello_world.c' contains a small "Hello World" Demo
5436 application; it is automatically compiled when you build U-Boot.
5437 It's configured to run at address 0x00040004, so you can play with it
5441 ## Ready for S-Record download ...
5442 ~>examples/hello_world.srec
5443 1 2 3 4 5 6 7 8 9 10 11 ...
5444 [file transfer complete]
5446 ## Start Addr = 0x00040004
5448 => go 40004 Hello World! This is a test.
5449 ## Starting application at 0x00040004 ...
5460 Hit any key to exit ...
5462 ## Application terminated, rc = 0x0
5464 Another example, which demonstrates how to register a CPM interrupt
5465 handler with the U-Boot code, can be found in 'examples/timer.c'.
5466 Here, a CPM timer is set up to generate an interrupt every second.
5467 The interrupt service routine is trivial, just printing a '.'
5468 character, but this is just a demo program. The application can be
5469 controlled by the following keys:
5471 ? - print current values og the CPM Timer registers
5472 b - enable interrupts and start timer
5473 e - stop timer and disable interrupts
5474 q - quit application
5477 ## Ready for S-Record download ...
5478 ~>examples/timer.srec
5479 1 2 3 4 5 6 7 8 9 10 11 ...
5480 [file transfer complete]
5482 ## Start Addr = 0x00040004
5485 ## Starting application at 0x00040004 ...
5488 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
5491 [q, b, e, ?] Set interval 1000000 us
5494 [q, b, e, ?] ........
5495 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
5498 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
5501 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
5504 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
5506 [q, b, e, ?] ...Stopping timer
5508 [q, b, e, ?] ## Application terminated, rc = 0x0
5514 Over time, many people have reported problems when trying to use the
5515 "minicom" terminal emulation program for serial download. I (wd)
5516 consider minicom to be broken, and recommend not to use it. Under
5517 Unix, I recommend to use C-Kermit for general purpose use (and
5518 especially for kermit binary protocol download ("loadb" command), and
5519 use "cu" for S-Record download ("loads" command). See
5520 http://www.denx.de/wiki/view/DULG/SystemSetup#Section_4.3.
5521 for help with kermit.
5524 Nevertheless, if you absolutely want to use it try adding this
5525 configuration to your "File transfer protocols" section:
5527 Name Program Name U/D FullScr IO-Red. Multi
5528 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
5529 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
5535 Starting at version 0.9.2, U-Boot supports NetBSD both as host
5536 (build U-Boot) and target system (boots NetBSD/mpc8xx).
5538 Building requires a cross environment; it is known to work on
5539 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
5540 need gmake since the Makefiles are not compatible with BSD make).
5541 Note that the cross-powerpc package does not install include files;
5542 attempting to build U-Boot will fail because <machine/ansi.h> is
5543 missing. This file has to be installed and patched manually:
5545 # cd /usr/pkg/cross/powerpc-netbsd/include
5547 # ln -s powerpc machine
5548 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
5549 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
5551 Native builds *don't* work due to incompatibilities between native
5552 and U-Boot include files.
5554 Booting assumes that (the first part of) the image booted is a
5555 stage-2 loader which in turn loads and then invokes the kernel
5556 proper. Loader sources will eventually appear in the NetBSD source
5557 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
5558 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
5561 Implementation Internals:
5562 =========================
5564 The following is not intended to be a complete description of every
5565 implementation detail. However, it should help to understand the
5566 inner workings of U-Boot and make it easier to port it to custom
5570 Initial Stack, Global Data:
5571 ---------------------------
5573 The implementation of U-Boot is complicated by the fact that U-Boot
5574 starts running out of ROM (flash memory), usually without access to
5575 system RAM (because the memory controller is not initialized yet).
5576 This means that we don't have writable Data or BSS segments, and BSS
5577 is not initialized as zero. To be able to get a C environment working
5578 at all, we have to allocate at least a minimal stack. Implementation
5579 options for this are defined and restricted by the CPU used: Some CPU
5580 models provide on-chip memory (like the IMMR area on MPC8xx and
5581 MPC826x processors), on others (parts of) the data cache can be
5582 locked as (mis-) used as memory, etc.
5584 Chris Hallinan posted a good summary of these issues to the
5585 U-Boot mailing list:
5587 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
5588 From: "Chris Hallinan" <clh@net1plus.com>
5589 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
5592 Correct me if I'm wrong, folks, but the way I understand it
5593 is this: Using DCACHE as initial RAM for Stack, etc, does not
5594 require any physical RAM backing up the cache. The cleverness
5595 is that the cache is being used as a temporary supply of
5596 necessary storage before the SDRAM controller is setup. It's
5597 beyond the scope of this list to explain the details, but you
5598 can see how this works by studying the cache architecture and
5599 operation in the architecture and processor-specific manuals.
5601 OCM is On Chip Memory, which I believe the 405GP has 4K. It
5602 is another option for the system designer to use as an
5603 initial stack/RAM area prior to SDRAM being available. Either
5604 option should work for you. Using CS 4 should be fine if your
5605 board designers haven't used it for something that would
5606 cause you grief during the initial boot! It is frequently not
5609 CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere
5610 with your processor/board/system design. The default value
5611 you will find in any recent u-boot distribution in
5612 walnut.h should work for you. I'd set it to a value larger
5613 than your SDRAM module. If you have a 64MB SDRAM module, set
5614 it above 400_0000. Just make sure your board has no resources
5615 that are supposed to respond to that address! That code in
5616 start.S has been around a while and should work as is when
5617 you get the config right.
5622 It is essential to remember this, since it has some impact on the C
5623 code for the initialization procedures:
5625 * Initialized global data (data segment) is read-only. Do not attempt
5628 * Do not use any uninitialized global data (or implicitely initialized
5629 as zero data - BSS segment) at all - this is undefined, initiali-
5630 zation is performed later (when relocating to RAM).
5632 * Stack space is very limited. Avoid big data buffers or things like
5635 Having only the stack as writable memory limits means we cannot use
5636 normal global data to share information beween the code. But it
5637 turned out that the implementation of U-Boot can be greatly
5638 simplified by making a global data structure (gd_t) available to all
5639 functions. We could pass a pointer to this data as argument to _all_
5640 functions, but this would bloat the code. Instead we use a feature of
5641 the GCC compiler (Global Register Variables) to share the data: we
5642 place a pointer (gd) to the global data into a register which we
5643 reserve for this purpose.
5645 When choosing a register for such a purpose we are restricted by the
5646 relevant (E)ABI specifications for the current architecture, and by
5647 GCC's implementation.
5649 For PowerPC, the following registers have specific use:
5651 R2: reserved for system use
5652 R3-R4: parameter passing and return values
5653 R5-R10: parameter passing
5654 R13: small data area pointer
5658 (U-Boot also uses R12 as internal GOT pointer. r12
5659 is a volatile register so r12 needs to be reset when
5660 going back and forth between asm and C)
5662 ==> U-Boot will use R2 to hold a pointer to the global data
5664 Note: on PPC, we could use a static initializer (since the
5665 address of the global data structure is known at compile time),
5666 but it turned out that reserving a register results in somewhat
5667 smaller code - although the code savings are not that big (on
5668 average for all boards 752 bytes for the whole U-Boot image,
5669 624 text + 127 data).
5671 On Blackfin, the normal C ABI (except for P3) is followed as documented here:
5672 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
5674 ==> U-Boot will use P3 to hold a pointer to the global data
5676 On ARM, the following registers are used:
5678 R0: function argument word/integer result
5679 R1-R3: function argument word
5680 R9: platform specific
5681 R10: stack limit (used only if stack checking is enabled)
5682 R11: argument (frame) pointer
5683 R12: temporary workspace
5686 R15: program counter
5688 ==> U-Boot will use R9 to hold a pointer to the global data
5690 Note: on ARM, only R_ARM_RELATIVE relocations are supported.
5692 On Nios II, the ABI is documented here:
5693 http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
5695 ==> U-Boot will use gp to hold a pointer to the global data
5697 Note: on Nios II, we give "-G0" option to gcc and don't use gp
5698 to access small data sections, so gp is free.
5700 On NDS32, the following registers are used:
5702 R0-R1: argument/return
5704 R15: temporary register for assembler
5705 R16: trampoline register
5706 R28: frame pointer (FP)
5707 R29: global pointer (GP)
5708 R30: link register (LP)
5709 R31: stack pointer (SP)
5710 PC: program counter (PC)
5712 ==> U-Boot will use R10 to hold a pointer to the global data
5714 NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
5715 or current versions of GCC may "optimize" the code too much.
5720 U-Boot runs in system state and uses physical addresses, i.e. the
5721 MMU is not used either for address mapping nor for memory protection.
5723 The available memory is mapped to fixed addresses using the memory
5724 controller. In this process, a contiguous block is formed for each
5725 memory type (Flash, SDRAM, SRAM), even when it consists of several
5726 physical memory banks.
5728 U-Boot is installed in the first 128 kB of the first Flash bank (on
5729 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
5730 booting and sizing and initializing DRAM, the code relocates itself
5731 to the upper end of DRAM. Immediately below the U-Boot code some
5732 memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN
5733 configuration setting]. Below that, a structure with global Board
5734 Info data is placed, followed by the stack (growing downward).
5736 Additionally, some exception handler code is copied to the low 8 kB
5737 of DRAM (0x00000000 ... 0x00001FFF).
5739 So a typical memory configuration with 16 MB of DRAM could look like
5742 0x0000 0000 Exception Vector code
5745 0x0000 2000 Free for Application Use
5751 0x00FB FF20 Monitor Stack (Growing downward)
5752 0x00FB FFAC Board Info Data and permanent copy of global data
5753 0x00FC 0000 Malloc Arena
5756 0x00FE 0000 RAM Copy of Monitor Code
5757 ... eventually: LCD or video framebuffer
5758 ... eventually: pRAM (Protected RAM - unchanged by reset)
5759 0x00FF FFFF [End of RAM]
5762 System Initialization:
5763 ----------------------
5765 In the reset configuration, U-Boot starts at the reset entry point
5766 (on most PowerPC systems at address 0x00000100). Because of the reset
5767 configuration for CS0# this is a mirror of the onboard Flash memory.
5768 To be able to re-map memory U-Boot then jumps to its link address.
5769 To be able to implement the initialization code in C, a (small!)
5770 initial stack is set up in the internal Dual Ported RAM (in case CPUs
5771 which provide such a feature like MPC8xx or MPC8260), or in a locked
5772 part of the data cache. After that, U-Boot initializes the CPU core,
5773 the caches and the SIU.
5775 Next, all (potentially) available memory banks are mapped using a
5776 preliminary mapping. For example, we put them on 512 MB boundaries
5777 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
5778 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
5779 programmed for SDRAM access. Using the temporary configuration, a
5780 simple memory test is run that determines the size of the SDRAM
5783 When there is more than one SDRAM bank, and the banks are of
5784 different size, the largest is mapped first. For equal size, the first
5785 bank (CS2#) is mapped first. The first mapping is always for address
5786 0x00000000, with any additional banks following immediately to create
5787 contiguous memory starting from 0.
5789 Then, the monitor installs itself at the upper end of the SDRAM area
5790 and allocates memory for use by malloc() and for the global Board
5791 Info data; also, the exception vector code is copied to the low RAM
5792 pages, and the final stack is set up.
5794 Only after this relocation will you have a "normal" C environment;
5795 until that you are restricted in several ways, mostly because you are
5796 running from ROM, and because the code will have to be relocated to a
5800 U-Boot Porting Guide:
5801 ----------------------
5803 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
5807 int main(int argc, char *argv[])
5809 sighandler_t no_more_time;
5811 signal(SIGALRM, no_more_time);
5812 alarm(PROJECT_DEADLINE - toSec (3 * WEEK));
5814 if (available_money > available_manpower) {
5815 Pay consultant to port U-Boot;
5819 Download latest U-Boot source;
5821 Subscribe to u-boot mailing list;
5824 email("Hi, I am new to U-Boot, how do I get started?");
5827 Read the README file in the top level directory;
5828 Read http://www.denx.de/twiki/bin/view/DULG/Manual;
5829 Read applicable doc/*.README;
5830 Read the source, Luke;
5831 /* find . -name "*.[chS]" | xargs grep -i <keyword> */
5834 if (available_money > toLocalCurrency ($2500))
5837 Add a lot of aggravation and time;
5839 if (a similar board exists) { /* hopefully... */
5840 cp -a board/<similar> board/<myboard>
5841 cp include/configs/<similar>.h include/configs/<myboard>.h
5843 Create your own board support subdirectory;
5844 Create your own board include/configs/<myboard>.h file;
5846 Edit new board/<myboard> files
5847 Edit new include/configs/<myboard>.h
5852 Add / modify source code;
5856 email("Hi, I am having problems...");
5858 Send patch file to the U-Boot email list;
5859 if (reasonable critiques)
5860 Incorporate improvements from email list code review;
5862 Defend code as written;
5868 void no_more_time (int sig)
5877 All contributions to U-Boot should conform to the Linux kernel
5878 coding style; see the file "Documentation/CodingStyle" and the script
5879 "scripts/Lindent" in your Linux kernel source directory.
5881 Source files originating from a different project (for example the
5882 MTD subsystem) are generally exempt from these guidelines and are not
5883 reformated to ease subsequent migration to newer versions of those
5886 Please note that U-Boot is implemented in C (and to some small parts in
5887 Assembler); no C++ is used, so please do not use C++ style comments (//)
5890 Please also stick to the following formatting rules:
5891 - remove any trailing white space
5892 - use TAB characters for indentation and vertical alignment, not spaces
5893 - make sure NOT to use DOS '\r\n' line feeds
5894 - do not add more than 2 consecutive empty lines to source files
5895 - do not add trailing empty lines to source files
5897 Submissions which do not conform to the standards may be returned
5898 with a request to reformat the changes.
5904 Since the number of patches for U-Boot is growing, we need to
5905 establish some rules. Submissions which do not conform to these rules
5906 may be rejected, even when they contain important and valuable stuff.
5908 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
5910 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
5911 see http://lists.denx.de/mailman/listinfo/u-boot
5913 When you send a patch, please include the following information with
5916 * For bug fixes: a description of the bug and how your patch fixes
5917 this bug. Please try to include a way of demonstrating that the
5918 patch actually fixes something.
5920 * For new features: a description of the feature and your
5923 * A CHANGELOG entry as plaintext (separate from the patch)
5925 * For major contributions, your entry to the CREDITS file
5927 * When you add support for a new board, don't forget to add a
5928 maintainer e-mail address to the boards.cfg file, too.
5930 * If your patch adds new configuration options, don't forget to
5931 document these in the README file.
5933 * The patch itself. If you are using git (which is *strongly*
5934 recommended) you can easily generate the patch using the
5935 "git format-patch". If you then use "git send-email" to send it to
5936 the U-Boot mailing list, you will avoid most of the common problems
5937 with some other mail clients.
5939 If you cannot use git, use "diff -purN OLD NEW". If your version of
5940 diff does not support these options, then get the latest version of
5943 The current directory when running this command shall be the parent
5944 directory of the U-Boot source tree (i. e. please make sure that
5945 your patch includes sufficient directory information for the
5948 We prefer patches as plain text. MIME attachments are discouraged,
5949 and compressed attachments must not be used.
5951 * If one logical set of modifications affects or creates several
5952 files, all these changes shall be submitted in a SINGLE patch file.
5954 * Changesets that contain different, unrelated modifications shall be
5955 submitted as SEPARATE patches, one patch per changeset.
5960 * Before sending the patch, run the MAKEALL script on your patched
5961 source tree and make sure that no errors or warnings are reported
5962 for any of the boards.
5964 * Keep your modifications to the necessary minimum: A patch
5965 containing several unrelated changes or arbitrary reformats will be
5966 returned with a request to re-formatting / split it.
5968 * If you modify existing code, make sure that your new code does not
5969 add to the memory footprint of the code ;-) Small is beautiful!
5970 When adding new features, these should compile conditionally only
5971 (using #ifdef), and the resulting code with the new feature
5972 disabled must not need more memory than the old code without your
5975 * Remember that there is a size limit of 100 kB per message on the
5976 u-boot mailing list. Bigger patches will be moderated. If they are
5977 reasonable and not too big, they will be acknowledged. But patches
5978 bigger than the size limit should be avoided.
projects / karo-tx-uboot.git / blob