arch/mips/cpu/mips32/au1x00/au1x00_usb_ohci.c

   1 /*
   2  * URB OHCI HCD (Host Controller Driver) for USB on the AU1x00.
   3  *
   4  * (C) Copyright 2003
   5  * Gary Jennejohn, DENX Software Engineering <garyj@denx.de>
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  * Note: Part of this code has been derived from linux
   9  *
  10  */
  11 /*
  12  * IMPORTANT NOTES
  13  * 1 - this driver is intended for use with USB Mass Storage Devices
  14  *     (BBB) ONLY. There is NO support for Interrupt or Isochronous pipes!
  15  */
  16
  17 #include <config.h>
  18
  19 #ifdef CONFIG_USB_OHCI
  20
  21 /* #include <pci.h> no PCI on the AU1x00 */
  22
  23 #include <common.h>
  24 #include <malloc.h>
  25 #include <asm/io.h>
  26 #include <asm/au1x00.h>
  27 #include <usb.h>
  28 #include "au1x00_usb_ohci.h"
  29
  30 #define OHCI_USE_NPS            /* force NoPowerSwitching mode */
  31 #define OHCI_VERBOSE_DEBUG      /* not always helpful */
  32 #define OHCI_FILL_TRACE
  33
  34 #define USBH_ENABLE_BE (1<<0)
  35 #define USBH_ENABLE_C  (1<<1)
  36 #define USBH_ENABLE_E  (1<<2)
  37 #define USBH_ENABLE_CE (1<<3)
  38 #define USBH_ENABLE_RD (1<<4)
  39
  40 #ifdef __LITTLE_ENDIAN
  41 #define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C)
  42 #else
  43 #define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C | USBH_ENABLE_BE)
  44 #endif
  45
  46
  47 /* For initializing controller (mask in an HCFS mode too) */
  48 #define OHCI_CONTROL_INIT \
  49         (OHCI_CTRL_CBSR & 0x3) | OHCI_CTRL_IE | OHCI_CTRL_PLE
  50
  51 #undef readl
  52 #undef writel
  53
  54 #define readl(a)     au_readl((long)(a))
  55 #define writel(v,a)  au_writel((v),(int)(a))
  56
  57 #define min_t(type,x,y) ({ type __x = (x); type __y = (y); __x < __y ? __x: __y; })
  58
  59 #define DEBUG
  60 #ifdef DEBUG
  61 #define dbg(format, arg...) printf("DEBUG: " format "\n", ## arg)
  62 #else
  63 #define dbg(format, arg...) do {} while(0)
  64 #endif /* DEBUG */
  65 #define err(format, arg...) printf("ERROR: " format "\n", ## arg)
  66 #define SHOW_INFO
  67 #ifdef SHOW_INFO
  68 #define info(format, arg...) printf("INFO: " format "\n", ## arg)
  69 #else
  70 #define info(format, arg...) do {} while(0)
  71 #endif
  72
  73 #define m16_swap(x) swap_16(x)
  74 #define m32_swap(x) swap_32(x)
  75
  76 /* global ohci_t */
  77 static ohci_t gohci;
  78 /* this must be aligned to a 256 byte boundary */
  79 struct ohci_hcca ghcca[1];
  80 /* a pointer to the aligned storage */
  81 struct ohci_hcca *phcca;
  82 /* this allocates EDs for all possible endpoints */
  83 struct ohci_device ohci_dev;
  84 /* urb_priv */
  85 urb_priv_t urb_priv;
  86 /* RHSC flag */
  87 int got_rhsc;
  88 /* device which was disconnected */
  89 struct usb_device *devgone;
  90
  91 /*-------------------------------------------------------------------------*/
  92
  93 /* AMD-756 (D2 rev) reports corrupt register contents in some cases.
  94  * The erratum (#4) description is incorrect.  AMD's workaround waits
  95  * till some bits (mostly reserved) are clear; ok for all revs.
  96  */
  97 #define OHCI_QUIRK_AMD756 0xabcd
  98 #define read_roothub(hc, register, mask) ({ \
  99         u32 temp = readl (&hc->regs->roothub.register); \
 100         if (hc->flags & OHCI_QUIRK_AMD756) \
 101                 while (temp & mask) \
 102                         temp = readl (&hc->regs->roothub.register); \
 103         temp; })
 104
 105 static u32 roothub_a (struct ohci *hc)
 106         { return read_roothub (hc, a, 0xfc0fe000); }
 107 static inline u32 roothub_b (struct ohci *hc)
 108         { return readl (&hc->regs->roothub.b); }
 109 static inline u32 roothub_status (struct ohci *hc)
 110         { return readl (&hc->regs->roothub.status); }
 111 static u32 roothub_portstatus (struct ohci *hc, int i)
 112         { return read_roothub (hc, portstatus [i], 0xffe0fce0); }
 113
 114
 115 /* forward declaration */
 116 static int hc_interrupt (void);
 117 static void
 118 td_submit_job (struct usb_device * dev, unsigned long pipe, void * buffer,
 119         int transfer_len, struct devrequest * setup, urb_priv_t * urb, int interval);
 120
 121 /*-------------------------------------------------------------------------*
 122  * URB support functions
 123  *-------------------------------------------------------------------------*/
 124
 125 /* free HCD-private data associated with this URB */
 126
 127 static void urb_free_priv (urb_priv_t * urb)
 128 {
 129         int             i;
 130         int             last;
 131         struct td       * td;
 132
 133         last = urb->length - 1;
 134         if (last >= 0) {
 135                 for (i = 0; i <= last; i++) {
 136                         td = urb->td[i];
 137                         if (td) {
 138                                 td->usb_dev = NULL;
 139                                 urb->td[i] = NULL;
 140                         }
 141                 }
 142         }
 143 }
 144
 145 /*-------------------------------------------------------------------------*/
 146
 147 #ifdef DEBUG
 148 static int sohci_get_current_frame_number (struct usb_device * dev);
 149
 150 /* debug| print the main components of an URB
 151  * small: 0) header + data packets 1) just header */
 152
 153 static void pkt_print (struct usb_device * dev, unsigned long pipe, void * buffer,
 154         int transfer_len, struct devrequest * setup, char * str, int small)
 155 {
 156         urb_priv_t * purb = &urb_priv;
 157
 158         dbg("%s URB:[%4x] dev:%2d,ep:%2d-%c,type:%s,len:%d/%d stat:%#lx",
 159                         str,
 160                         sohci_get_current_frame_number (dev),
 161                         usb_pipedevice (pipe),
 162                         usb_pipeendpoint (pipe),
 163                         usb_pipeout (pipe)? 'O': 'I',
 164                         usb_pipetype (pipe) < 2? (usb_pipeint (pipe)? "INTR": "ISOC"):
 165                                 (usb_pipecontrol (pipe)? "CTRL": "BULK"),
 166                         purb->actual_length,
 167                         transfer_len, dev->status);
 168 #ifdef  OHCI_VERBOSE_DEBUG
 169         if (!small) {
 170                 int i, len;
 171
 172                 if (usb_pipecontrol (pipe)) {
 173                         printf (__FILE__ ": cmd(8):");
 174                         for (i = 0; i < 8 ; i++)
 175                                 printf (" %02x", ((__u8 *) setup) [i]);
 176                         printf ("\n");
 177                 }
 178                 if (transfer_len > 0 && buffer) {
 179                         printf (__FILE__ ": data(%d/%d):",
 180                                 purb->actual_length,
 181                                 transfer_len);
 182                         len = usb_pipeout (pipe)?
 183                                         transfer_len: purb->actual_length;
 184                         for (i = 0; i < 16 && i < len; i++)
 185                                 printf (" %02x", ((__u8 *) buffer) [i]);
 186                         printf ("%s\n", i < len? "...": "");
 187                 }
 188         }
 189 #endif
 190 }
 191
 192 /* just for debugging; prints non-empty branches of the int ed tree inclusive iso eds*/
 193 void ep_print_int_eds (ohci_t *ohci, char * str) {
 194         int i, j;
 195          __u32 * ed_p;
 196         for (i= 0; i < 32; i++) {
 197                 j = 5;
 198                 ed_p = &(ohci->hcca->int_table [i]);
 199                 if (*ed_p == 0)
 200                     continue;
 201                 printf (__FILE__ ": %s branch int %2d(%2x):", str, i, i);
 202                 while (*ed_p != 0 && j--) {
 203                         ed_t *ed = (ed_t *)m32_swap(ed_p);
 204                         printf (" ed: %4x;", ed->hwINFO);
 205                         ed_p = &ed->hwNextED;
 206                 }
 207                 printf ("\n");
 208         }
 209 }
 210
 211 static void ohci_dump_intr_mask (char *label, __u32 mask)
 212 {
 213         dbg ("%s: 0x%08x%s%s%s%s%s%s%s%s%s",
 214                 label,
 215                 mask,
 216                 (mask & OHCI_INTR_MIE) ? " MIE" : "",
 217                 (mask & OHCI_INTR_OC) ? " OC" : "",
 218                 (mask & OHCI_INTR_RHSC) ? " RHSC" : "",
 219                 (mask & OHCI_INTR_FNO) ? " FNO" : "",
 220                 (mask & OHCI_INTR_UE) ? " UE" : "",
 221                 (mask & OHCI_INTR_RD) ? " RD" : "",
 222                 (mask & OHCI_INTR_SF) ? " SF" : "",
 223                 (mask & OHCI_INTR_WDH) ? " WDH" : "",
 224                 (mask & OHCI_INTR_SO) ? " SO" : ""
 225                 );
 226 }
 227
 228 static void maybe_print_eds (char *label, __u32 value)
 229 {
 230         ed_t *edp = (ed_t *)value;
 231
 232         if (value) {
 233                 dbg ("%s %08x", label, value);
 234                 dbg ("%08x", edp->hwINFO);
 235                 dbg ("%08x", edp->hwTailP);
 236                 dbg ("%08x", edp->hwHeadP);
 237                 dbg ("%08x", edp->hwNextED);
 238         }
 239 }
 240
 241 static char * hcfs2string (int state)
 242 {
 243         switch (state) {
 244                 case OHCI_USB_RESET:    return "reset";
 245                 case OHCI_USB_RESUME:   return "resume";
 246                 case OHCI_USB_OPER:     return "operational";
 247                 case OHCI_USB_SUSPEND:  return "suspend";
 248         }
 249         return "?";
 250 }
 251
 252 /* dump control and status registers */
 253 static void ohci_dump_status (ohci_t *controller)
 254 {
 255         struct ohci_regs        *regs = controller->regs;
 256         __u32                   temp;
 257
 258         temp = readl (&regs->revision) & 0xff;
 259         if (temp != 0x10)
 260                 dbg ("spec %d.%d", (temp >> 4), (temp & 0x0f));
 261
 262         temp = readl (&regs->control);
 263         dbg ("control: 0x%08x%s%s%s HCFS=%s%s%s%s%s CBSR=%d", temp,
 264                 (temp & OHCI_CTRL_RWE) ? " RWE" : "",
 265                 (temp & OHCI_CTRL_RWC) ? " RWC" : "",
 266                 (temp & OHCI_CTRL_IR) ? " IR" : "",
 267                 hcfs2string (temp & OHCI_CTRL_HCFS),
 268                 (temp & OHCI_CTRL_BLE) ? " BLE" : "",
 269                 (temp & OHCI_CTRL_CLE) ? " CLE" : "",
 270                 (temp & OHCI_CTRL_IE) ? " IE" : "",
 271                 (temp & OHCI_CTRL_PLE) ? " PLE" : "",
 272                 temp & OHCI_CTRL_CBSR
 273                 );
 274
 275         temp = readl (&regs->cmdstatus);
 276         dbg ("cmdstatus: 0x%08x SOC=%d%s%s%s%s", temp,
 277                 (temp & OHCI_SOC) >> 16,
 278                 (temp & OHCI_OCR) ? " OCR" : "",
 279                 (temp & OHCI_BLF) ? " BLF" : "",
 280                 (temp & OHCI_CLF) ? " CLF" : "",
 281                 (temp & OHCI_HCR) ? " HCR" : ""
 282                 );
 283
 284         ohci_dump_intr_mask ("intrstatus", readl (&regs->intrstatus));
 285         ohci_dump_intr_mask ("intrenable", readl (&regs->intrenable));
 286
 287         maybe_print_eds ("ed_periodcurrent", readl (&regs->ed_periodcurrent));
 288
 289         maybe_print_eds ("ed_controlhead", readl (&regs->ed_controlhead));
 290         maybe_print_eds ("ed_controlcurrent", readl (&regs->ed_controlcurrent));
 291
 292         maybe_print_eds ("ed_bulkhead", readl (&regs->ed_bulkhead));
 293         maybe_print_eds ("ed_bulkcurrent", readl (&regs->ed_bulkcurrent));
 294
 295         maybe_print_eds ("donehead", readl (&regs->donehead));
 296 }
 297
 298 static void ohci_dump_roothub (ohci_t *controller, int verbose)
 299 {
 300         __u32                   temp, ndp, i;
 301
 302         temp = roothub_a (controller);
 303         ndp = (temp & RH_A_NDP);
 304
 305         if (verbose) {
 306                 dbg ("roothub.a: %08x POTPGT=%d%s%s%s%s%s NDP=%d", temp,
 307                         ((temp & RH_A_POTPGT) >> 24) & 0xff,
 308                         (temp & RH_A_NOCP) ? " NOCP" : "",
 309                         (temp & RH_A_OCPM) ? " OCPM" : "",
 310                         (temp & RH_A_DT) ? " DT" : "",
 311                         (temp & RH_A_NPS) ? " NPS" : "",
 312                         (temp & RH_A_PSM) ? " PSM" : "",
 313                         ndp
 314                         );
 315                 temp = roothub_b (controller);
 316                 dbg ("roothub.b: %08x PPCM=%04x DR=%04x",
 317                         temp,
 318                         (temp & RH_B_PPCM) >> 16,
 319                         (temp & RH_B_DR)
 320                         );
 321                 temp = roothub_status (controller);
 322                 dbg ("roothub.status: %08x%s%s%s%s%s%s",
 323                         temp,
 324                         (temp & RH_HS_CRWE) ? " CRWE" : "",
 325                         (temp & RH_HS_OCIC) ? " OCIC" : "",
 326                         (temp & RH_HS_LPSC) ? " LPSC" : "",
 327                         (temp & RH_HS_DRWE) ? " DRWE" : "",
 328                         (temp & RH_HS_OCI) ? " OCI" : "",
 329                         (temp & RH_HS_LPS) ? " LPS" : ""
 330                         );
 331         }
 332
 333         for (i = 0; i < ndp; i++) {
 334                 temp = roothub_portstatus (controller, i);
 335                 dbg ("roothub.portstatus [%d] = 0x%08x%s%s%s%s%s%s%s%s%s%s%s%s",
 336                         i,
 337                         temp,
 338                         (temp & RH_PS_PRSC) ? " PRSC" : "",
 339                         (temp & RH_PS_OCIC) ? " OCIC" : "",
 340                         (temp & RH_PS_PSSC) ? " PSSC" : "",
 341                         (temp & RH_PS_PESC) ? " PESC" : "",
 342                         (temp & RH_PS_CSC) ? " CSC" : "",
 343
 344                         (temp & RH_PS_LSDA) ? " LSDA" : "",
 345                         (temp & RH_PS_PPS) ? " PPS" : "",
 346                         (temp & RH_PS_PRS) ? " PRS" : "",
 347                         (temp & RH_PS_POCI) ? " POCI" : "",
 348                         (temp & RH_PS_PSS) ? " PSS" : "",
 349
 350                         (temp & RH_PS_PES) ? " PES" : "",
 351                         (temp & RH_PS_CCS) ? " CCS" : ""
 352                         );
 353         }
 354 }
 355
 356 static void ohci_dump (ohci_t *controller, int verbose)
 357 {
 358         dbg ("OHCI controller usb-%s state", controller->slot_name);
 359
 360         /* dumps some of the state we know about */
 361         ohci_dump_status (controller);
 362         if (verbose)
 363                 ep_print_int_eds (controller, "hcca");
 364         dbg ("hcca frame #%04x", controller->hcca->frame_no);
 365         ohci_dump_roothub (controller, 1);
 366 }
 367
 368
 369 #endif /* DEBUG */
 370
 371 /*-------------------------------------------------------------------------*
 372  * Interface functions (URB)
 373  *-------------------------------------------------------------------------*/
 374
 375 /* get a transfer request */
 376
 377 int sohci_submit_job(struct usb_device *dev, unsigned long pipe, void *buffer,
 378                 int transfer_len, struct devrequest *setup, int interval)
 379 {
 380         ohci_t *ohci;
 381         ed_t * ed;
 382         urb_priv_t *purb_priv;
 383         int i, size = 0;
 384
 385         ohci = &gohci;
 386
 387         /* when controller's hung, permit only roothub cleanup attempts
 388          * such as powering down ports */
 389         if (ohci->disabled) {
 390                 err("sohci_submit_job: EPIPE");
 391                 return -1;
 392         }
 393
 394         /* every endpoint has a ed, locate and fill it */
 395         if (!(ed = ep_add_ed (dev, pipe))) {
 396                 err("sohci_submit_job: ENOMEM");
 397                 return -1;
 398         }
 399
 400         /* for the private part of the URB we need the number of TDs (size) */
 401         switch (usb_pipetype (pipe)) {
 402                 case PIPE_BULK: /* one TD for every 4096 Byte */
 403                         size = (transfer_len - 1) / 4096 + 1;
 404                         break;
 405                 case PIPE_CONTROL: /* 1 TD for setup, 1 for ACK and 1 for every 4096 B */
 406                         size = (transfer_len == 0)? 2:
 407                                                 (transfer_len - 1) / 4096 + 3;
 408                         break;
 409         }
 410
 411         if (size >= (N_URB_TD - 1)) {
 412                 err("need %d TDs, only have %d", size, N_URB_TD);
 413                 return -1;
 414         }
 415         purb_priv = &urb_priv;
 416         purb_priv->pipe = pipe;
 417
 418         /* fill the private part of the URB */
 419         purb_priv->length = size;
 420         purb_priv->ed = ed;
 421         purb_priv->actual_length = 0;
 422
 423         /* allocate the TDs */
 424         /* note that td[0] was allocated in ep_add_ed */
 425         for (i = 0; i < size; i++) {
 426                 purb_priv->td[i] = td_alloc (dev);
 427                 if (!purb_priv->td[i]) {
 428                         purb_priv->length = i;
 429                         urb_free_priv (purb_priv);
 430                         err("sohci_submit_job: ENOMEM");
 431                         return -1;
 432                 }
 433         }
 434
 435         if (ed->state == ED_NEW || (ed->state & ED_DEL)) {
 436                 urb_free_priv (purb_priv);
 437                 err("sohci_submit_job: EINVAL");
 438                 return -1;
 439         }
 440
 441         /* link the ed into a chain if is not already */
 442         if (ed->state != ED_OPER)
 443                 ep_link (ohci, ed);
 444
 445         /* fill the TDs and link it to the ed */
 446         td_submit_job(dev, pipe, buffer, transfer_len, setup, purb_priv, interval);
 447
 448         return 0;
 449 }
 450
 451 /*-------------------------------------------------------------------------*/
 452
 453 #ifdef DEBUG
 454 /* tell us the current USB frame number */
 455
 456 static int sohci_get_current_frame_number (struct usb_device *usb_dev)
 457 {
 458         ohci_t *ohci = &gohci;
 459
 460         return m16_swap (ohci->hcca->frame_no);
 461 }
 462 #endif
 463
 464 /*-------------------------------------------------------------------------*
 465  * ED handling functions
 466  *-------------------------------------------------------------------------*/
 467
 468 /* link an ed into one of the HC chains */
 469
 470 static int ep_link (ohci_t *ohci, ed_t *edi)
 471 {
 472         volatile ed_t *ed = edi;
 473
 474         ed->state = ED_OPER;
 475
 476         switch (ed->type) {
 477         case PIPE_CONTROL:
 478                 ed->hwNextED = 0;
 479                 if (ohci->ed_controltail == NULL) {
 480                         writel ((long)ed, &ohci->regs->ed_controlhead);
 481                 } else {
 482                         ohci->ed_controltail->hwNextED = m32_swap (ed);
 483                 }
 484                 ed->ed_prev = ohci->ed_controltail;
 485                 if (!ohci->ed_controltail && !ohci->ed_rm_list[0] &&
 486                         !ohci->ed_rm_list[1] && !ohci->sleeping) {
 487                         ohci->hc_control |= OHCI_CTRL_CLE;
 488                         writel (ohci->hc_control, &ohci->regs->control);
 489                 }
 490                 ohci->ed_controltail = edi;
 491                 break;
 492
 493         case PIPE_BULK:
 494                 ed->hwNextED = 0;
 495                 if (ohci->ed_bulktail == NULL) {
 496                         writel ((long)ed, &ohci->regs->ed_bulkhead);
 497                 } else {
 498                         ohci->ed_bulktail->hwNextED = m32_swap (ed);
 499                 }
 500                 ed->ed_prev = ohci->ed_bulktail;
 501                 if (!ohci->ed_bulktail && !ohci->ed_rm_list[0] &&
 502                         !ohci->ed_rm_list[1] && !ohci->sleeping) {
 503                         ohci->hc_control |= OHCI_CTRL_BLE;
 504                         writel (ohci->hc_control, &ohci->regs->control);
 505                 }
 506                 ohci->ed_bulktail = edi;
 507                 break;
 508         }
 509         return 0;
 510 }
 511
 512 /*-------------------------------------------------------------------------*/
 513
 514 /* unlink an ed from one of the HC chains.
 515  * just the link to the ed is unlinked.
 516  * the link from the ed still points to another operational ed or 0
 517  * so the HC can eventually finish the processing of the unlinked ed */
 518
 519 static int ep_unlink (ohci_t *ohci, ed_t *ed)
 520 {
 521         ed->hwINFO |= m32_swap (OHCI_ED_SKIP);
 522
 523         switch (ed->type) {
 524         case PIPE_CONTROL:
 525                 if (ed->ed_prev == NULL) {
 526                         if (!ed->hwNextED) {
 527                                 ohci->hc_control &= ~OHCI_CTRL_CLE;
 528                                 writel (ohci->hc_control, &ohci->regs->control);
 529                         }
 530                         writel (m32_swap (*((__u32 *)&ed->hwNextED)), &ohci->regs->ed_controlhead);
 531                 } else {
 532                         ed->ed_prev->hwNextED = ed->hwNextED;
 533                 }
 534                 if (ohci->ed_controltail == ed) {
 535                         ohci->ed_controltail = ed->ed_prev;
 536                 } else {
 537                         ((ed_t *)m32_swap (*((__u32 *)&ed->hwNextED)))->ed_prev = ed->ed_prev;
 538                 }
 539                 break;
 540
 541         case PIPE_BULK:
 542                 if (ed->ed_prev == NULL) {
 543                         if (!ed->hwNextED) {
 544                                 ohci->hc_control &= ~OHCI_CTRL_BLE;
 545                                 writel (ohci->hc_control, &ohci->regs->control);
 546                         }
 547                         writel (m32_swap (*((__u32 *)&ed->hwNextED)), &ohci->regs->ed_bulkhead);
 548                 } else {
 549                         ed->ed_prev->hwNextED = ed->hwNextED;
 550                 }
 551                 if (ohci->ed_bulktail == ed) {
 552                         ohci->ed_bulktail = ed->ed_prev;
 553                 } else {
 554                         ((ed_t *)m32_swap (*((__u32 *)&ed->hwNextED)))->ed_prev = ed->ed_prev;
 555                 }
 556                 break;
 557         }
 558         ed->state = ED_UNLINK;
 559         return 0;
 560 }
 561
 562
 563 /*-------------------------------------------------------------------------*/
 564
 565 /* add/reinit an endpoint; this should be done once at the usb_set_configuration command,
 566  * but the USB stack is a little bit stateless  so we do it at every transaction
 567  * if the state of the ed is ED_NEW then a dummy td is added and the state is changed to ED_UNLINK
 568  * in all other cases the state is left unchanged
 569  * the ed info fields are setted anyway even though most of them should not change */
 570
 571 static ed_t * ep_add_ed (struct usb_device *usb_dev, unsigned long pipe)
 572 {
 573         td_t *td;
 574         ed_t *ed_ret;
 575         volatile ed_t *ed;
 576
 577         ed = ed_ret = &ohci_dev.ed[(usb_pipeendpoint (pipe) << 1) |
 578                         (usb_pipecontrol (pipe)? 0: usb_pipeout (pipe))];
 579
 580         if ((ed->state & ED_DEL) || (ed->state & ED_URB_DEL)) {
 581                 err("ep_add_ed: pending delete");
 582                 /* pending delete request */
 583                 return NULL;
 584         }
 585
 586         if (ed->state == ED_NEW) {
 587                 ed->hwINFO = m32_swap (OHCI_ED_SKIP); /* skip ed */
 588                 /* dummy td; end of td list for ed */
 589                 td = td_alloc (usb_dev);
 590                 ed->hwTailP = m32_swap (td);
 591                 ed->hwHeadP = ed->hwTailP;
 592                 ed->state = ED_UNLINK;
 593                 ed->type = usb_pipetype (pipe);
 594                 ohci_dev.ed_cnt++;
 595         }
 596
 597         ed->hwINFO = m32_swap (usb_pipedevice (pipe)
 598                         | usb_pipeendpoint (pipe) << 7
 599                         | (usb_pipeisoc (pipe)? 0x8000: 0)
 600                         | (usb_pipecontrol (pipe)? 0: (usb_pipeout (pipe)? 0x800: 0x1000))
 601                         | (usb_dev->speed == USB_SPEED_LOW) << 13
 602                         | usb_maxpacket (usb_dev, pipe) << 16);
 603
 604         return ed_ret;
 605 }
 606
 607 /*-------------------------------------------------------------------------*
 608  * TD handling functions
 609  *-------------------------------------------------------------------------*/
 610
 611 /* enqueue next TD for this URB (OHCI spec 5.2.8.2) */
 612
 613 static void td_fill (ohci_t *ohci, unsigned int info,
 614         void *data, int len,
 615         struct usb_device *dev, int index, urb_priv_t *urb_priv)
 616 {
 617         volatile td_t  *td, *td_pt;
 618 #ifdef OHCI_FILL_TRACE
 619         int i;
 620 #endif
 621
 622         if (index > urb_priv->length) {
 623                 err("index > length");
 624                 return;
 625         }
 626         /* use this td as the next dummy */
 627         td_pt = urb_priv->td [index];
 628         td_pt->hwNextTD = 0;
 629
 630         /* fill the old dummy TD */
 631         td = urb_priv->td [index] = (td_t *)(m32_swap (urb_priv->ed->hwTailP) & ~0xf);
 632
 633         td->ed = urb_priv->ed;
 634         td->next_dl_td = NULL;
 635         td->index = index;
 636         td->data = (__u32)data;
 637 #ifdef OHCI_FILL_TRACE
 638         if (1 || (usb_pipebulk(urb_priv->pipe) &&
 639                                 usb_pipeout(urb_priv->pipe))) {
 640                 for (i = 0; i < len; i++)
 641                 printf("td->data[%d] %#2x\n",i, ((unsigned char *)(td->data+0x80000000))[i]);
 642         }
 643 #endif
 644         if (!len)
 645                 data = 0;
 646
 647         td->hwINFO = m32_swap (info);
 648         td->hwCBP = m32_swap (data);
 649         if (data)
 650                 td->hwBE = m32_swap (data + len - 1);
 651         else
 652                 td->hwBE = 0;
 653         td->hwNextTD = m32_swap (td_pt);
 654         td->hwPSW [0] = m16_swap (((__u32)data & 0x0FFF) | 0xE000);
 655
 656         /* append to queue */
 657         td->ed->hwTailP = td->hwNextTD;
 658 }
 659
 660 /*-------------------------------------------------------------------------*/
 661
 662 /* prepare all TDs of a transfer */
 663
 664 #define kseg_to_phys(x)   ((void *)((__u32)(x) - 0x80000000))
 665
 666 static void td_submit_job (struct usb_device *dev, unsigned long pipe, void *buffer,
 667         int transfer_len, struct devrequest *setup, urb_priv_t *urb, int interval)
 668 {
 669         ohci_t *ohci = &gohci;
 670         int data_len = transfer_len;
 671         void *data;
 672         int cnt = 0;
 673         __u32 info = 0;
 674         unsigned int toggle = 0;
 675
 676         /* OHCI handles the DATA-toggles itself, we just use the USB-toggle bits for reseting */
 677         if(usb_gettoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe))) {
 678                 toggle = TD_T_TOGGLE;
 679         } else {
 680                 toggle = TD_T_DATA0;
 681                 usb_settoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe), 1);
 682         }
 683         urb->td_cnt = 0;
 684         if (data_len)
 685                 data = kseg_to_phys(buffer);
 686         else
 687                 data = 0;
 688
 689         switch (usb_pipetype (pipe)) {
 690         case PIPE_BULK:
 691                 info = usb_pipeout (pipe)?
 692                         TD_CC | TD_DP_OUT : TD_CC | TD_DP_IN ;
 693                 while(data_len > 4096) {
 694                         td_fill (ohci, info | (cnt? TD_T_TOGGLE:toggle), data, 4096, dev, cnt, urb);
 695                         data += 4096; data_len -= 4096; cnt++;
 696                 }
 697                 info = usb_pipeout (pipe)?
 698                         TD_CC | TD_DP_OUT : TD_CC | TD_R | TD_DP_IN ;
 699                 td_fill (ohci, info | (cnt? TD_T_TOGGLE:toggle), data, data_len, dev, cnt, urb);
 700                 cnt++;
 701
 702                 if (!ohci->sleeping)
 703                         writel (OHCI_BLF, &ohci->regs->cmdstatus); /* start bulk list */
 704                 break;
 705
 706         case PIPE_CONTROL:
 707                 info = TD_CC | TD_DP_SETUP | TD_T_DATA0;
 708                 td_fill (ohci, info, kseg_to_phys(setup), 8, dev, cnt++, urb);
 709                 if (data_len > 0) {
 710                         info = usb_pipeout (pipe)?
 711                                 TD_CC | TD_R | TD_DP_OUT | TD_T_DATA1 : TD_CC | TD_R | TD_DP_IN | TD_T_DATA1;
 712                         /* NOTE:  mishandles transfers >8K, some >4K */
 713                         td_fill (ohci, info, data, data_len, dev, cnt++, urb);
 714                 }
 715                 info = usb_pipeout (pipe)?
 716                         TD_CC | TD_DP_IN | TD_T_DATA1: TD_CC | TD_DP_OUT | TD_T_DATA1;
 717                 td_fill (ohci, info, data, 0, dev, cnt++, urb);
 718                 if (!ohci->sleeping)
 719                         writel (OHCI_CLF, &ohci->regs->cmdstatus); /* start Control list */
 720                 break;
 721         }
 722         if (urb->length != cnt)
 723                 dbg("TD LENGTH %d != CNT %d", urb->length, cnt);
 724 }
 725
 726 /*-------------------------------------------------------------------------*
 727  * Done List handling functions
 728  *-------------------------------------------------------------------------*/
 729
 730
 731 /* calculate the transfer length and update the urb */
 732
 733 static void dl_transfer_length(td_t * td)
 734 {
 735         __u32 tdINFO, tdBE, tdCBP;
 736         urb_priv_t *lurb_priv = &urb_priv;
 737
 738         tdINFO = m32_swap (td->hwINFO);
 739         tdBE   = m32_swap (td->hwBE);
 740         tdCBP  = m32_swap (td->hwCBP);
 741
 742
 743         if (!(usb_pipecontrol(lurb_priv->pipe) &&
 744             ((td->index == 0) || (td->index == lurb_priv->length - 1)))) {
 745                 if (tdBE != 0) {
 746                         if (td->hwCBP == 0)
 747                                 lurb_priv->actual_length += tdBE - td->data + 1;
 748                         else
 749                                 lurb_priv->actual_length += tdCBP - td->data;
 750                 }
 751         }
 752 }
 753
 754 /*-------------------------------------------------------------------------*/
 755
 756 /* replies to the request have to be on a FIFO basis so
 757  * we reverse the reversed done-list */
 758
 759 static td_t * dl_reverse_done_list (ohci_t *ohci)
 760 {
 761         __u32 td_list_hc;
 762         td_t *td_rev = NULL;
 763         td_t *td_list = NULL;
 764         urb_priv_t *lurb_priv = NULL;
 765
 766         td_list_hc = m32_swap (ohci->hcca->done_head) & 0xfffffff0;
 767         ohci->hcca->done_head = 0;
 768
 769         while (td_list_hc) {
 770                 td_list = (td_t *)td_list_hc;
 771
 772                 if (TD_CC_GET (m32_swap (td_list->hwINFO))) {
 773                         lurb_priv = &urb_priv;
 774                         dbg(" USB-error/status: %x : %p",
 775                                         TD_CC_GET (m32_swap (td_list->hwINFO)), td_list);
 776                         if (td_list->ed->hwHeadP & m32_swap (0x1)) {
 777                                 if (lurb_priv && ((td_list->index + 1) < lurb_priv->length)) {
 778                                         td_list->ed->hwHeadP =
 779                                                 (lurb_priv->td[lurb_priv->length - 1]->hwNextTD & m32_swap (0xfffffff0)) |
 780                                                                         (td_list->ed->hwHeadP & m32_swap (0x2));
 781                                         lurb_priv->td_cnt += lurb_priv->length - td_list->index - 1;
 782                                 } else
 783                                         td_list->ed->hwHeadP &= m32_swap (0xfffffff2);
 784                         }
 785                 }
 786
 787                 td_list->next_dl_td = td_rev;
 788                 td_rev = td_list;
 789                 td_list_hc = m32_swap (td_list->hwNextTD) & 0xfffffff0;
 790         }
 791         return td_list;
 792 }
 793
 794 /*-------------------------------------------------------------------------*/
 795
 796 /* td done list */
 797 static int dl_done_list (ohci_t *ohci, td_t *td_list)
 798 {
 799         td_t *td_list_next = NULL;
 800         ed_t *ed;
 801         int cc = 0;
 802         int stat = 0;
 803         /* urb_t *urb; */
 804         urb_priv_t *lurb_priv;
 805         __u32 tdINFO, edHeadP, edTailP;
 806
 807         while (td_list) {
 808                 td_list_next = td_list->next_dl_td;
 809
 810                 lurb_priv = &urb_priv;
 811                 tdINFO = m32_swap (td_list->hwINFO);
 812
 813                 ed = td_list->ed;
 814
 815                 dl_transfer_length(td_list);
 816
 817                 /* error code of transfer */
 818                 cc = TD_CC_GET (tdINFO);
 819                 if (cc != 0) {
 820                         dbg("ConditionCode %#x", cc);
 821                         stat = cc_to_error[cc];
 822                 }
 823
 824                 if (ed->state != ED_NEW) {
 825                         edHeadP = m32_swap (ed->hwHeadP) & 0xfffffff0;
 826                         edTailP = m32_swap (ed->hwTailP);
 827
 828                         /* unlink eds if they are not busy */
 829                         if ((edHeadP == edTailP) && (ed->state == ED_OPER))
 830                                 ep_unlink (ohci, ed);
 831                 }
 832
 833                 td_list = td_list_next;
 834         }
 835         return stat;
 836 }
 837
 838 /*-------------------------------------------------------------------------*
 839  * Virtual Root Hub
 840  *-------------------------------------------------------------------------*/
 841
 842 /* Device descriptor */
 843 static __u8 root_hub_dev_des[] =
 844 {
 845         0x12,       /*  __u8  bLength; */
 846         0x01,       /*  __u8  bDescriptorType; Device */
 847         0x10,       /*  __u16 bcdUSB; v1.1 */
 848         0x01,
 849         0x09,       /*  __u8  bDeviceClass; HUB_CLASSCODE */
 850         0x00,       /*  __u8  bDeviceSubClass; */
 851         0x00,       /*  __u8  bDeviceProtocol; */
 852         0x08,       /*  __u8  bMaxPacketSize0; 8 Bytes */
 853         0x00,       /*  __u16 idVendor; */
 854         0x00,
 855         0x00,       /*  __u16 idProduct; */
 856         0x00,
 857         0x00,       /*  __u16 bcdDevice; */
 858         0x00,
 859         0x00,       /*  __u8  iManufacturer; */
 860         0x01,       /*  __u8  iProduct; */
 861         0x00,       /*  __u8  iSerialNumber; */
 862         0x01        /*  __u8  bNumConfigurations; */
 863 };
 864
 865
 866 /* Configuration descriptor */
 867 static __u8 root_hub_config_des[] =
 868 {
 869         0x09,       /*  __u8  bLength; */
 870         0x02,       /*  __u8  bDescriptorType; Configuration */
 871         0x19,       /*  __u16 wTotalLength; */
 872         0x00,
 873         0x01,       /*  __u8  bNumInterfaces; */
 874         0x01,       /*  __u8  bConfigurationValue; */
 875         0x00,       /*  __u8  iConfiguration; */
 876         0x40,       /*  __u8  bmAttributes;
 877                  Bit 7: Bus-powered, 6: Self-powered, 5 Remote-wakwup, 4..0: resvd */
 878         0x00,       /*  __u8  MaxPower; */
 879
 880         /* interface */
 881         0x09,       /*  __u8  if_bLength; */
 882         0x04,       /*  __u8  if_bDescriptorType; Interface */
 883         0x00,       /*  __u8  if_bInterfaceNumber; */
 884         0x00,       /*  __u8  if_bAlternateSetting; */
 885         0x01,       /*  __u8  if_bNumEndpoints; */
 886         0x09,       /*  __u8  if_bInterfaceClass; HUB_CLASSCODE */
 887         0x00,       /*  __u8  if_bInterfaceSubClass; */
 888         0x00,       /*  __u8  if_bInterfaceProtocol; */
 889         0x00,       /*  __u8  if_iInterface; */
 890
 891         /* endpoint */
 892         0x07,       /*  __u8  ep_bLength; */
 893         0x05,       /*  __u8  ep_bDescriptorType; Endpoint */
 894         0x81,       /*  __u8  ep_bEndpointAddress; IN Endpoint 1 */
 895         0x03,       /*  __u8  ep_bmAttributes; Interrupt */
 896         0x02,       /*  __u16 ep_wMaxPacketSize; ((MAX_ROOT_PORTS + 1) / 8 */
 897         0x00,
 898         0xff        /*  __u8  ep_bInterval; 255 ms */
 899 };
 900
 901 static unsigned char root_hub_str_index0[] =
 902 {
 903         0x04,                   /*  __u8  bLength; */
 904         0x03,                   /*  __u8  bDescriptorType; String-descriptor */
 905         0x09,                   /*  __u8  lang ID */
 906         0x04,                   /*  __u8  lang ID */
 907 };
 908
 909 static unsigned char root_hub_str_index1[] =
 910 {
 911         28,                     /*  __u8  bLength; */
 912         0x03,                   /*  __u8  bDescriptorType; String-descriptor */
 913         'O',                    /*  __u8  Unicode */
 914         0,                              /*  __u8  Unicode */
 915         'H',                    /*  __u8  Unicode */
 916         0,                              /*  __u8  Unicode */
 917         'C',                    /*  __u8  Unicode */
 918         0,                              /*  __u8  Unicode */
 919         'I',                    /*  __u8  Unicode */
 920         0,                              /*  __u8  Unicode */
 921         ' ',                    /*  __u8  Unicode */
 922         0,                              /*  __u8  Unicode */
 923         'R',                    /*  __u8  Unicode */
 924         0,                              /*  __u8  Unicode */
 925         'o',                    /*  __u8  Unicode */
 926         0,                              /*  __u8  Unicode */
 927         'o',                    /*  __u8  Unicode */
 928         0,                              /*  __u8  Unicode */
 929         't',                    /*  __u8  Unicode */
 930         0,                              /*  __u8  Unicode */
 931         ' ',                    /*  __u8  Unicode */
 932         0,                              /*  __u8  Unicode */
 933         'H',                    /*  __u8  Unicode */
 934         0,                              /*  __u8  Unicode */
 935         'u',                    /*  __u8  Unicode */
 936         0,                              /*  __u8  Unicode */
 937         'b',                    /*  __u8  Unicode */
 938         0,                              /*  __u8  Unicode */
 939 };
 940
 941 /* Hub class-specific descriptor is constructed dynamically */
 942
 943
 944 /*-------------------------------------------------------------------------*/
 945
 946 #define OK(x)                   len = (x); break
 947 #ifdef DEBUG
 948 #define WR_RH_STAT(x)           {info("WR:status %#8x", (x));writel((x), &gohci.regs->roothub.status);}
 949 #define WR_RH_PORTSTAT(x)       {info("WR:portstatus[%d] %#8x", wIndex-1, (x));writel((x), &gohci.regs->roothub.portstatus[wIndex-1]);}
 950 #else
 951 #define WR_RH_STAT(x)           writel((x), &gohci.regs->roothub.status)
 952 #define WR_RH_PORTSTAT(x)       writel((x), &gohci.regs->roothub.portstatus[wIndex-1])
 953 #endif
 954 #define RD_RH_STAT              roothub_status(&gohci)
 955 #define RD_RH_PORTSTAT          roothub_portstatus(&gohci,wIndex-1)
 956
 957 /* request to virtual root hub */
 958
 959 int rh_check_port_status(ohci_t *controller)
 960 {
 961         __u32 temp, ndp, i;
 962         int res;
 963
 964         res = -1;
 965         temp = roothub_a (controller);
 966         ndp = (temp & RH_A_NDP);
 967         for (i = 0; i < ndp; i++) {
 968                 temp = roothub_portstatus (controller, i);
 969                 /* check for a device disconnect */
 970                 if (((temp & (RH_PS_PESC | RH_PS_CSC)) ==
 971                         (RH_PS_PESC | RH_PS_CSC)) &&
 972                         ((temp & RH_PS_CCS) == 0)) {
 973                         res = i;
 974                         break;
 975                 }
 976         }
 977         return res;
 978 }
 979
 980 static int ohci_submit_rh_msg(struct usb_device *dev, unsigned long pipe,
 981                 void *buffer, int transfer_len, struct devrequest *cmd)
 982 {
 983         void * data = buffer;
 984         int leni = transfer_len;
 985         int len = 0;
 986         int stat = 0;
 987         __u32 datab[4];
 988         __u8 *data_buf = (__u8 *)datab;
 989         __u16 bmRType_bReq;
 990         __u16 wValue;
 991         __u16 wIndex;
 992         __u16 wLength;
 993
 994 #ifdef DEBUG
 995 urb_priv.actual_length = 0;
 996 pkt_print(dev, pipe, buffer, transfer_len, cmd, "SUB(rh)", usb_pipein(pipe));
 997 #else
 998         mdelay(1);
 999 #endif
1000         if (usb_pipeint(pipe)) {
1001                 info("Root-Hub submit IRQ: NOT implemented");
1002                 return 0;
1003         }
1004
1005         bmRType_bReq  = cmd->requesttype | (cmd->request << 8);
1006         wValue        = m16_swap (cmd->value);
1007         wIndex        = m16_swap (cmd->index);
1008         wLength       = m16_swap (cmd->length);
1009
1010         info("Root-Hub: adr: %2x cmd(%1x): %08x %04x %04x %04x",
1011                 dev->devnum, 8, bmRType_bReq, wValue, wIndex, wLength);
1012
1013         switch (bmRType_bReq) {
1014         /* Request Destination:
1015            without flags: Device,
1016            RH_INTERFACE: interface,
1017            RH_ENDPOINT: endpoint,
1018            RH_CLASS means HUB here,
1019            RH_OTHER | RH_CLASS  almost ever means HUB_PORT here
1020         */
1021
1022         case RH_GET_STATUS:
1023                         *(__u16 *) data_buf = m16_swap (1); OK (2);
1024         case RH_GET_STATUS | RH_INTERFACE:
1025                         *(__u16 *) data_buf = m16_swap (0); OK (2);
1026         case RH_GET_STATUS | RH_ENDPOINT:
1027                         *(__u16 *) data_buf = m16_swap (0); OK (2);
1028         case RH_GET_STATUS | RH_CLASS:
1029                         *(__u32 *) data_buf = m32_swap (
1030                                 RD_RH_STAT & ~(RH_HS_CRWE | RH_HS_DRWE));
1031                         OK (4);
1032         case RH_GET_STATUS | RH_OTHER | RH_CLASS:
1033                         *(__u32 *) data_buf = m32_swap (RD_RH_PORTSTAT); OK (4);
1034
1035         case RH_CLEAR_FEATURE | RH_ENDPOINT:
1036                 switch (wValue) {
1037                         case (RH_ENDPOINT_STALL): OK (0);
1038                 }
1039                 break;
1040
1041         case RH_CLEAR_FEATURE | RH_CLASS:
1042                 switch (wValue) {
1043                         case RH_C_HUB_LOCAL_POWER:
1044                                 OK(0);
1045                         case (RH_C_HUB_OVER_CURRENT):
1046                                         WR_RH_STAT(RH_HS_OCIC); OK (0);
1047                 }
1048                 break;
1049
1050         case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS:
1051                 switch (wValue) {
1052                         case (RH_PORT_ENABLE):
1053                                         WR_RH_PORTSTAT (RH_PS_CCS ); OK (0);
1054                         case (RH_PORT_SUSPEND):
1055                                         WR_RH_PORTSTAT (RH_PS_POCI); OK (0);
1056                         case (RH_PORT_POWER):
1057                                         WR_RH_PORTSTAT (RH_PS_LSDA); OK (0);
1058                         case (RH_C_PORT_CONNECTION):
1059                                         WR_RH_PORTSTAT (RH_PS_CSC ); OK (0);
1060                         case (RH_C_PORT_ENABLE):
1061                                         WR_RH_PORTSTAT (RH_PS_PESC); OK (0);
1062                         case (RH_C_PORT_SUSPEND):
1063                                         WR_RH_PORTSTAT (RH_PS_PSSC); OK (0);
1064                         case (RH_C_PORT_OVER_CURRENT):
1065                                         WR_RH_PORTSTAT (RH_PS_OCIC); OK (0);
1066                         case (RH_C_PORT_RESET):
1067                                         WR_RH_PORTSTAT (RH_PS_PRSC); OK (0);
1068                 }
1069                 break;
1070
1071         case RH_SET_FEATURE | RH_OTHER | RH_CLASS:
1072                 switch (wValue) {
1073                         case (RH_PORT_SUSPEND):
1074                                         WR_RH_PORTSTAT (RH_PS_PSS ); OK (0);
1075                         case (RH_PORT_RESET): /* BUG IN HUP CODE *********/
1076                                         if (RD_RH_PORTSTAT & RH_PS_CCS)
1077                                             WR_RH_PORTSTAT (RH_PS_PRS);
1078                                         OK (0);
1079                         case (RH_PORT_POWER):
1080                                         WR_RH_PORTSTAT (RH_PS_PPS ); OK (0);
1081                         case (RH_PORT_ENABLE): /* BUG IN HUP CODE *********/
1082                                         if (RD_RH_PORTSTAT & RH_PS_CCS)
1083                                             WR_RH_PORTSTAT (RH_PS_PES );
1084                                         OK (0);
1085                 }
1086                 break;
1087
1088         case RH_SET_ADDRESS: gohci.rh.devnum = wValue; OK(0);
1089
1090         case RH_GET_DESCRIPTOR:
1091                 switch ((wValue & 0xff00) >> 8) {
1092                         case (0x01): /* device descriptor */
1093                                 len = min_t(unsigned int,
1094                                           leni,
1095                                           min_t(unsigned int,
1096                                               sizeof (root_hub_dev_des),
1097                                               wLength));
1098                                 data_buf = root_hub_dev_des; OK(len);
1099                         case (0x02): /* configuration descriptor */
1100                                 len = min_t(unsigned int,
1101                                           leni,
1102                                           min_t(unsigned int,
1103                                               sizeof (root_hub_config_des),
1104                                               wLength));
1105                                 data_buf = root_hub_config_des; OK(len);
1106                         case (0x03): /* string descriptors */
1107                                 if(wValue==0x0300) {
1108                                         len = min_t(unsigned int,
1109                                                   leni,
1110                                                   min_t(unsigned int,
1111                                                       sizeof (root_hub_str_index0),
1112                                                       wLength));
1113                                         data_buf = root_hub_str_index0;
1114                                         OK(len);
1115                                 }
1116                                 if(wValue==0x0301) {
1117                                         len = min_t(unsigned int,
1118                                                   leni,
1119                                                   min_t(unsigned int,
1120                                                       sizeof (root_hub_str_index1),
1121                                                       wLength));
1122                                         data_buf = root_hub_str_index1;
1123                                         OK(len);
1124                         }
1125                         default:
1126                                 stat = USB_ST_STALLED;
1127                 }
1128                 break;
1129
1130         case RH_GET_DESCRIPTOR | RH_CLASS:
1131             {
1132                     __u32 temp = roothub_a (&gohci);
1133
1134                     data_buf [0] = 9;           /* min length; */
1135                     data_buf [1] = 0x29;
1136                     data_buf [2] = temp & RH_A_NDP;
1137                     data_buf [3] = 0;
1138                     if (temp & RH_A_PSM)        /* per-port power switching? */
1139                         data_buf [3] |= 0x1;
1140                     if (temp & RH_A_NOCP)       /* no overcurrent reporting? */
1141                         data_buf [3] |= 0x10;
1142                     else if (temp & RH_A_OCPM)  /* per-port overcurrent reporting? */
1143                         data_buf [3] |= 0x8;
1144
1145                     /* corresponds to data_buf[4-7] */
1146                     datab [1] = 0;
1147                     data_buf [5] = (temp & RH_A_POTPGT) >> 24;
1148                     temp = roothub_b (&gohci);
1149                     data_buf [7] = temp & RH_B_DR;
1150                     if (data_buf [2] < 7) {
1151                         data_buf [8] = 0xff;
1152                     } else {
1153                         data_buf [0] += 2;
1154                         data_buf [8] = (temp & RH_B_DR) >> 8;
1155                         data_buf [10] = data_buf [9] = 0xff;
1156                     }
1157
1158                     len = min_t(unsigned int, leni,
1159                               min_t(unsigned int, data_buf [0], wLength));
1160                     OK (len);
1161                 }
1162
1163         case RH_GET_CONFIGURATION:      *(__u8 *) data_buf = 0x01; OK (1);
1164
1165         case RH_SET_CONFIGURATION:      WR_RH_STAT (0x10000); OK (0);
1166
1167         default:
1168                 dbg ("unsupported root hub command");
1169                 stat = USB_ST_STALLED;
1170         }
1171
1172 #ifdef  DEBUG
1173         ohci_dump_roothub (&gohci, 1);
1174 #else
1175         mdelay(1);
1176 #endif
1177
1178         len = min_t(int, len, leni);
1179         if (data != data_buf)
1180             memcpy (data, data_buf, len);
1181         dev->act_len = len;
1182         dev->status = stat;
1183
1184 #ifdef DEBUG
1185         if (transfer_len)
1186                 urb_priv.actual_length = transfer_len;
1187         pkt_print(dev, pipe, buffer, transfer_len, cmd, "RET(rh)", 0/*usb_pipein(pipe)*/);
1188 #else
1189         mdelay(1);
1190 #endif
1191
1192         return stat;
1193 }
1194
1195 /*-------------------------------------------------------------------------*/
1196
1197 /* common code for handling submit messages - used for all but root hub */
1198 /* accesses. */
1199 int submit_common_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
1200                 int transfer_len, struct devrequest *setup, int interval)
1201 {
1202         int stat = 0;
1203         int maxsize = usb_maxpacket(dev, pipe);
1204         int timeout;
1205
1206         /* device pulled? Shortcut the action. */
1207         if (devgone == dev) {
1208                 dev->status = USB_ST_CRC_ERR;
1209                 return 0;
1210         }
1211
1212 #ifdef DEBUG
1213         urb_priv.actual_length = 0;
1214         pkt_print(dev, pipe, buffer, transfer_len, setup, "SUB", usb_pipein(pipe));
1215 #else
1216         mdelay(1);
1217 #endif
1218         if (!maxsize) {
1219                 err("submit_common_message: pipesize for pipe %lx is zero",
1220                         pipe);
1221                 return -1;
1222         }
1223
1224         if (sohci_submit_job(dev, pipe, buffer, transfer_len, setup, interval) < 0) {
1225                 err("sohci_submit_job failed");
1226                 return -1;
1227         }
1228
1229         mdelay(10);
1230         /* ohci_dump_status(&gohci); */
1231
1232         /* allow more time for a BULK device to react - some are slow */
1233 #define BULK_TO  5000   /* timeout in milliseconds */
1234         if (usb_pipebulk(pipe))
1235                 timeout = BULK_TO;
1236         else
1237                 timeout = 100;
1238
1239         timeout *= 4;
1240         /* wait for it to complete */
1241         for (;;) {
1242                 /* check whether the controller is done */
1243                 stat = hc_interrupt();
1244                 if (stat < 0) {
1245                         stat = USB_ST_CRC_ERR;
1246                         break;
1247                 }
1248                 if (stat >= 0 && stat != 0xff) {
1249                         /* 0xff is returned for an SF-interrupt */
1250                         break;
1251                 }
1252                 if (--timeout) {
1253                         udelay(250); /* mdelay(1); */
1254                 } else {
1255                         err("CTL:TIMEOUT ");
1256                         stat = USB_ST_CRC_ERR;
1257                         break;
1258                 }
1259         }
1260         /* we got an Root Hub Status Change interrupt */
1261         if (got_rhsc) {
1262 #ifdef DEBUG
1263                 ohci_dump_roothub (&gohci, 1);
1264 #endif
1265                 got_rhsc = 0;
1266                 /* abuse timeout */
1267                 timeout = rh_check_port_status(&gohci);
1268                 if (timeout >= 0) {
1269 #if 0 /* this does nothing useful, but leave it here in case that changes */
1270                         /* the called routine adds 1 to the passed value */
1271                         usb_hub_port_connect_change(gohci.rh.dev, timeout - 1);
1272 #endif
1273                         /*
1274                          * XXX
1275                          * This is potentially dangerous because it assumes
1276                          * that only one device is ever plugged in!
1277                          */
1278                         devgone = dev;
1279                 }
1280         }
1281
1282         dev->status = stat;
1283         dev->act_len = transfer_len;
1284
1285 #ifdef DEBUG
1286         pkt_print(dev, pipe, buffer, transfer_len, setup, "RET(ctlr)", usb_pipein(pipe));
1287 #else
1288         mdelay(1);
1289 #endif
1290
1291         /* free TDs in urb_priv */
1292         urb_free_priv (&urb_priv);
1293         return 0;
1294 }
1295
1296 /* submit routines called from usb.c */
1297 int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
1298                 int transfer_len)
1299 {
1300         info("submit_bulk_msg");
1301         return submit_common_msg(dev, pipe, buffer, transfer_len, NULL, 0);
1302 }
1303
1304 int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
1305                 int transfer_len, struct devrequest *setup)
1306 {
1307         int maxsize = usb_maxpacket(dev, pipe);
1308
1309         info("submit_control_msg");
1310 #ifdef DEBUG
1311         urb_priv.actual_length = 0;
1312         pkt_print(dev, pipe, buffer, transfer_len, setup, "SUB", usb_pipein(pipe));
1313 #else
1314         mdelay(1);
1315 #endif
1316         if (!maxsize) {
1317                 err("submit_control_message: pipesize for pipe %lx is zero",
1318                         pipe);
1319                 return -1;
1320         }
1321         if (((pipe >> 8) & 0x7f) == gohci.rh.devnum) {
1322                 gohci.rh.dev = dev;
1323                 /* root hub - redirect */
1324                 return ohci_submit_rh_msg(dev, pipe, buffer, transfer_len,
1325                         setup);
1326         }
1327
1328         return submit_common_msg(dev, pipe, buffer, transfer_len, setup, 0);
1329 }
1330
1331 int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
1332                 int transfer_len, int interval)
1333 {
1334         info("submit_int_msg");
1335         return -1;
1336 }
1337
1338 /*-------------------------------------------------------------------------*
1339  * HC functions
1340  *-------------------------------------------------------------------------*/
1341
1342 /* reset the HC and BUS */
1343
1344 static int hc_reset (ohci_t *ohci)
1345 {
1346         int timeout = 30;
1347         int smm_timeout = 50; /* 0,5 sec */
1348
1349         if (readl (&ohci->regs->control) & OHCI_CTRL_IR) { /* SMM owns the HC */
1350                 writel (OHCI_OCR, &ohci->regs->cmdstatus); /* request ownership */
1351                 info("USB HC TakeOver from SMM");
1352                 while (readl (&ohci->regs->control) & OHCI_CTRL_IR) {
1353                         mdelay (10);
1354                         if (--smm_timeout == 0) {
1355                                 err("USB HC TakeOver failed!");
1356                                 return -1;
1357                         }
1358                 }
1359         }
1360
1361         /* Disable HC interrupts */
1362         writel (OHCI_INTR_MIE, &ohci->regs->intrdisable);
1363
1364         dbg("USB HC reset_hc usb-%s: ctrl = 0x%X ;",
1365                 ohci->slot_name,
1366                 readl (&ohci->regs->control));
1367
1368         /* Reset USB (needed by some controllers) */
1369         writel (0, &ohci->regs->control);
1370
1371         /* HC Reset requires max 10 us delay */
1372         writel (OHCI_HCR,  &ohci->regs->cmdstatus);
1373         while ((readl (&ohci->regs->cmdstatus) & OHCI_HCR) != 0) {
1374                 if (--timeout == 0) {
1375                         err("USB HC reset timed out!");
1376                         return -1;
1377                 }
1378                 udelay (1);
1379         }
1380         return 0;
1381 }
1382
1383 /*-------------------------------------------------------------------------*/
1384
1385 /* Start an OHCI controller, set the BUS operational
1386  * enable interrupts
1387  * connect the virtual root hub */
1388
1389 static int hc_start (ohci_t * ohci)
1390 {
1391         __u32 mask;
1392         unsigned int fminterval;
1393
1394         ohci->disabled = 1;
1395
1396         /* Tell the controller where the control and bulk lists are
1397          * The lists are empty now. */
1398
1399         writel (0, &ohci->regs->ed_controlhead);
1400         writel (0, &ohci->regs->ed_bulkhead);
1401
1402         writel ((__u32)ohci->hcca, &ohci->regs->hcca); /* a reset clears this */
1403
1404         fminterval = 0x2edf;
1405         writel ((fminterval * 9) / 10, &ohci->regs->periodicstart);
1406         fminterval |= ((((fminterval - 210) * 6) / 7) << 16);
1407         writel (fminterval, &ohci->regs->fminterval);
1408         writel (0x628, &ohci->regs->lsthresh);
1409
1410         /* start controller operations */
1411         ohci->hc_control = OHCI_CONTROL_INIT | OHCI_USB_OPER;
1412         ohci->disabled = 0;
1413         writel (ohci->hc_control, &ohci->regs->control);
1414
1415         /* disable all interrupts */
1416         mask = (OHCI_INTR_SO | OHCI_INTR_WDH | OHCI_INTR_SF | OHCI_INTR_RD |
1417                         OHCI_INTR_UE | OHCI_INTR_FNO | OHCI_INTR_RHSC |
1418                         OHCI_INTR_OC | OHCI_INTR_MIE);
1419         writel (mask, &ohci->regs->intrdisable);
1420         /* clear all interrupts */
1421         mask &= ~OHCI_INTR_MIE;
1422         writel (mask, &ohci->regs->intrstatus);
1423         /* Choose the interrupts we care about now  - but w/o MIE */
1424         mask = OHCI_INTR_RHSC | OHCI_INTR_UE | OHCI_INTR_WDH | OHCI_INTR_SO;
1425         writel (mask, &ohci->regs->intrenable);
1426
1427 #ifdef  OHCI_USE_NPS
1428         /* required for AMD-756 and some Mac platforms */
1429         writel ((roothub_a (ohci) | RH_A_NPS) & ~RH_A_PSM,
1430                 &ohci->regs->roothub.a);
1431         writel (RH_HS_LPSC, &ohci->regs->roothub.status);
1432 #endif  /* OHCI_USE_NPS */
1433
1434         /* POTPGT delay is bits 24-31, in 2 ms units. */
1435         mdelay ((roothub_a (ohci) >> 23) & 0x1fe);
1436
1437         /* connect the virtual root hub */
1438         ohci->rh.devnum = 0;
1439
1440         return 0;
1441 }
1442
1443 /*-------------------------------------------------------------------------*/
1444
1445 /* an interrupt happens */
1446
1447 static int
1448 hc_interrupt (void)
1449 {
1450         ohci_t *ohci = &gohci;
1451         struct ohci_regs *regs = ohci->regs;
1452         int ints;
1453         int stat = -1;
1454
1455         if ((ohci->hcca->done_head != 0) && !(m32_swap (ohci->hcca->done_head) & 0x01)) {
1456                 ints =  OHCI_INTR_WDH;
1457         } else {
1458                 ints = readl (&regs->intrstatus);
1459         }
1460
1461         /* dbg("Interrupt: %x frame: %x", ints, le16_to_cpu (ohci->hcca->frame_no)); */
1462
1463         if (ints & OHCI_INTR_RHSC) {
1464                 got_rhsc = 1;
1465         }
1466
1467         if (ints & OHCI_INTR_UE) {
1468                 ohci->disabled++;
1469                 err ("OHCI Unrecoverable Error, controller usb-%s disabled",
1470                         ohci->slot_name);
1471                 /* e.g. due to PCI Master/Target Abort */
1472
1473 #ifdef  DEBUG
1474                 ohci_dump (ohci, 1);
1475 #else
1476         mdelay(1);
1477 #endif
1478                 /* FIXME: be optimistic, hope that bug won't repeat often. */
1479                 /* Make some non-interrupt context restart the controller. */
1480                 /* Count and limit the retries though; either hardware or */
1481                 /* software errors can go forever... */
1482                 hc_reset (ohci);
1483                 return -1;
1484         }
1485
1486         if (ints & OHCI_INTR_WDH) {
1487                 mdelay(1);
1488                 writel (OHCI_INTR_WDH, &regs->intrdisable);
1489                 stat = dl_done_list (&gohci, dl_reverse_done_list (&gohci));
1490                 writel (OHCI_INTR_WDH, &regs->intrenable);
1491         }
1492
1493         if (ints & OHCI_INTR_SO) {
1494                 dbg("USB Schedule overrun\n");
1495                 writel (OHCI_INTR_SO, &regs->intrenable);
1496                 stat = -1;
1497         }
1498
1499         /* FIXME:  this assumes SOF (1/ms) interrupts don't get lost... */
1500         if (ints & OHCI_INTR_SF) {
1501                 unsigned int frame = m16_swap (ohci->hcca->frame_no) & 1;
1502                 mdelay(1);
1503                 writel (OHCI_INTR_SF, &regs->intrdisable);
1504                 if (ohci->ed_rm_list[frame] != NULL)
1505                         writel (OHCI_INTR_SF, &regs->intrenable);
1506                 stat = 0xff;
1507         }
1508
1509         writel (ints, &regs->intrstatus);
1510         return stat;
1511 }
1512
1513 /*-------------------------------------------------------------------------*/
1514
1515 /*-------------------------------------------------------------------------*/
1516
1517 /* De-allocate all resources.. */
1518
1519 static void hc_release_ohci (ohci_t *ohci)
1520 {
1521         dbg ("USB HC release ohci usb-%s", ohci->slot_name);
1522
1523         if (!ohci->disabled)
1524                 hc_reset (ohci);
1525 }
1526
1527 /*-------------------------------------------------------------------------*/
1528
1529 #define __read_32bit_c0_register(source, sel)                           \
1530 ({ int __res;                                                           \
1531         if (sel == 0)                                                   \
1532                 __asm__ __volatile__(                                   \
1533                         "mfc0\t%0, " #source "\n\t"                     \
1534                         : "=r" (__res));                                \
1535         else                                                            \
1536                 __asm__ __volatile__(                                   \
1537                         ".set\tmips32\n\t"                              \
1538                         "mfc0\t%0, " #source ", " #sel "\n\t"           \
1539                         ".set\tmips0\n\t"                               \
1540                         : "=r" (__res));                                \
1541         __res;                                                          \
1542 })
1543
1544 #define read_c0_prid()          __read_32bit_c0_register($15, 0)
1545
1546 /*
1547  * low level initalisation routine, called from usb.c
1548  */
1549 static char ohci_inited = 0;
1550
1551 int usb_lowlevel_init(int index, void **controller)
1552 {
1553         u32 pin_func;
1554         u32 sys_freqctrl, sys_clksrc;
1555         u32 prid = read_c0_prid();
1556
1557         dbg("in usb_lowlevel_init\n");
1558
1559         /* zero and disable FREQ2 */
1560         sys_freqctrl = au_readl(SYS_FREQCTRL0);
1561         sys_freqctrl &= ~0xFFF00000;
1562         au_writel(sys_freqctrl, SYS_FREQCTRL0);
1563
1564         /* zero and disable USBH/USBD clocks */
1565         sys_clksrc = au_readl(SYS_CLKSRC);
1566         sys_clksrc &= ~0x00007FE0;
1567         au_writel(sys_clksrc, SYS_CLKSRC);
1568
1569         sys_freqctrl = au_readl(SYS_FREQCTRL0);
1570         sys_freqctrl &= ~0xFFF00000;
1571
1572         sys_clksrc = au_readl(SYS_CLKSRC);
1573         sys_clksrc &= ~0x00007FE0;
1574
1575         switch (prid & 0x000000FF) {
1576         case 0x00: /* DA */
1577         case 0x01: /* HA */
1578         case 0x02: /* HB */
1579                 /* CPU core freq to 48MHz to slow it way down... */
1580                 au_writel(4, SYS_CPUPLL);
1581
1582                 /*
1583                  * Setup 48MHz FREQ2 from CPUPLL for USB Host
1584                  */
1585                 /* FRDIV2=3 -> div by 8 of 384MHz -> 48MHz */
1586                 sys_freqctrl |= ((3<<22) | (1<<21) | (0<<20));
1587                 au_writel(sys_freqctrl, SYS_FREQCTRL0);
1588
1589                 /* CPU core freq to 384MHz */
1590                 au_writel(0x20, SYS_CPUPLL);
1591
1592                 printf("Au1000: 48MHz OHCI workaround enabled\n");
1593                 break;
1594
1595         default:  /* HC and newer */
1596                 /* FREQ2 = aux/2 = 48 MHz */
1597                 sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
1598                 au_writel(sys_freqctrl, SYS_FREQCTRL0);
1599                 break;
1600         }
1601
1602         /*
1603          * Route 48MHz FREQ2 into USB Host and/or Device
1604          */
1605         sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
1606         au_writel(sys_clksrc, SYS_CLKSRC);
1607
1608         /* configure pins GPIO[14:9] as GPIO */
1609         pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8080);
1610
1611         au_writel(pin_func, SYS_PINFUNC);
1612         au_writel(0x2800, SYS_TRIOUTCLR);
1613         au_writel(0x0030, SYS_OUTPUTCLR);
1614
1615         dbg("OHCI board setup complete\n");
1616
1617         /* enable host controller */
1618         au_writel(USBH_ENABLE_CE, USB_HOST_CONFIG);
1619         udelay(1000);
1620         au_writel(USBH_ENABLE_INIT, USB_HOST_CONFIG);
1621         udelay(1000);
1622
1623         /* wait for reset complete (read register twice; see au1500 errata) */
1624         while (au_readl(USB_HOST_CONFIG),
1625                !(au_readl(USB_HOST_CONFIG) & USBH_ENABLE_RD))
1626                 udelay(1000);
1627
1628         dbg("OHCI clock running\n");
1629
1630         memset (&gohci, 0, sizeof (ohci_t));
1631         memset (&urb_priv, 0, sizeof (urb_priv_t));
1632
1633         /* align the storage */
1634         if ((__u32)&ghcca[0] & 0xff) {
1635                 err("HCCA not aligned!!");
1636                 return -1;
1637         }
1638         phcca = &ghcca[0];
1639         info("aligned ghcca %p", phcca);
1640         memset(&ohci_dev, 0, sizeof(struct ohci_device));
1641         if ((__u32)&ohci_dev.ed[0] & 0x7) {
1642                 err("EDs not aligned!!");
1643                 return -1;
1644         }
1645         memset(gtd, 0, sizeof(td_t) * (NUM_TD + 1));
1646         if ((__u32)gtd & 0x7) {
1647                 err("TDs not aligned!!");
1648                 return -1;
1649         }
1650         ptd = gtd;
1651         gohci.hcca = phcca;
1652         memset (phcca, 0, sizeof (struct ohci_hcca));
1653
1654         gohci.disabled = 1;
1655         gohci.sleeping = 0;
1656         gohci.irq = -1;
1657         gohci.regs = (struct ohci_regs *)(USB_OHCI_BASE | 0xA0000000);
1658
1659         gohci.flags = 0;
1660         gohci.slot_name = "au1x00";
1661
1662         dbg("OHCI revision: 0x%08x\n"
1663                "  RH: a: 0x%08x b: 0x%08x\n",
1664                readl(&gohci.regs->revision),
1665                readl(&gohci.regs->roothub.a), readl(&gohci.regs->roothub.b));
1666
1667         if (hc_reset (&gohci) < 0)
1668                 goto errout;
1669
1670         /* FIXME this is a second HC reset; why?? */
1671         writel (gohci.hc_control = OHCI_USB_RESET, &gohci.regs->control);
1672         mdelay (10);
1673
1674         if (hc_start (&gohci) < 0)
1675                 goto errout;
1676
1677 #ifdef  DEBUG
1678         ohci_dump (&gohci, 1);
1679 #else
1680         mdelay(1);
1681 #endif
1682         ohci_inited = 1;
1683         return 0;
1684
1685   errout:
1686         err("OHCI initialization error\n");
1687         hc_release_ohci (&gohci);
1688         /* Initialization failed */
1689         au_writel(readl(USB_HOST_CONFIG) & ~USBH_ENABLE_CE, USB_HOST_CONFIG);
1690         return -1;
1691 }
1692
1693 int usb_lowlevel_stop(int index)
1694 {
1695         /* this gets called really early - before the controller has */
1696         /* even been initialized! */
1697         if (!ohci_inited)
1698                 return 0;
1699         /* TODO release any interrupts, etc. */
1700         /* call hc_release_ohci() here ? */
1701         hc_reset (&gohci);
1702         /* may not want to do this */
1703         /* Disable clock */
1704         au_writel(readl(USB_HOST_CONFIG) & ~USBH_ENABLE_CE, USB_HOST_CONFIG);
1705         return 0;
1706 }
1707
1708 #endif /* CONFIG_USB_OHCI */