include/configs/cam_enc_4xx.h

   1 /*
   2  * Copyright (C) 2009 Texas Instruments Incorporated
   3  *
   4  * Copyright (C) 2011
   5  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #define CONFIG_SYS_NO_FLASH             /* that is, no *NOR* flash */
  14 #define CONFIG_SYS_CONSOLE_INFO_QUIET
  15
  16 /* SoC Configuration */
  17 #define CONFIG_SYS_TIMERBASE            0x01c21400      /* use timer 0 */
  18 #define CONFIG_SYS_HZ_CLOCK             24000000        /* timer0 freq */
  19 #define CONFIG_SOC_DM365
  20
  21 #define CONFIG_MACH_TYPE        MACH_TYPE_DAVINCI_DM365_EVM
  22
  23 #define CONFIG_HOSTNAME                 cam_enc_4xx
  24
  25 #define CONFIG_BOARD_LATE_INIT
  26 #define CONFIG_CAM_ENC_LED_MASK         0x0fc00000
  27
  28 /* Memory Info */
  29 #define CONFIG_NR_DRAM_BANKS            1
  30 #define PHYS_SDRAM_1                    0x80000000
  31 #define PHYS_SDRAM_1_SIZE               (256 << 20)     /* 256 MiB */
  32 #define DDR_4BANKS                              /* 4-bank DDR2 (256MB) */
  33 #define CONFIG_MAX_RAM_BANK_SIZE        (256 << 20)     /* 256 MB */
  34 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
  35
  36 /* Serial Driver info: UART0 for console  */
  37 #define CONFIG_SYS_NS16550
  38 #define CONFIG_SYS_NS16550_SERIAL
  39 #define CONFIG_SYS_NS16550_REG_SIZE     -4
  40 #define CONFIG_SYS_NS16550_COM1         0x01c20000
  41 #define CONFIG_SYS_NS16550_CLK          CONFIG_SYS_HZ_CLOCK
  42 #define CONFIG_CONS_INDEX               1
  43 #define CONFIG_BAUDRATE                 115200
  44
  45 /* Network Configuration */
  46 #define CONFIG_DRIVER_TI_EMAC
  47 #define CONFIG_EMAC_MDIO_PHY_NUM        0
  48 #define CONFIG_SYS_EMAC_TI_CLKDIV       0xa9    /* 1MHz */
  49 #define CONFIG_MII
  50 #define CONFIG_BOOTP_DNS
  51 #define CONFIG_BOOTP_DNS2
  52 #define CONFIG_BOOTP_SEND_HOSTNAME
  53 #define CONFIG_NET_RETRY_COUNT  10
  54 #define CONFIG_CMD_MII
  55 #define CONFIG_SYS_DCACHE_OFF
  56 #define CONFIG_RESET_PHY_R
  57
  58 /* I2C */
  59 #define CONFIG_SYS_I2C
  60 #define CONFIG_SYS_I2C_DAVINCI
  61 #define CONFIG_SYS_DAVINCI_I2C_SPEED            400000
  62 #define CONFIG_SYS_DAVINCI_I2C_SLAVE            0x10    /* SMBus host address */
  63
  64 /* NAND: socketed, two chipselects, normally 2 GBytes */
  65 #define CONFIG_NAND_DAVINCI
  66 #define CONFIG_SYS_NAND_CS              2
  67 #define CONFIG_SYS_NAND_USE_FLASH_BBT
  68 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
  69 #define CONFIG_SYS_NAND_PAGE_2K
  70
  71 #define CONFIG_SYS_NAND_LARGEPAGE
  72 #define CONFIG_SYS_NAND_BASE_LIST       { 0x02000000, }
  73 /* socket has two chipselects, nCE0 gated by address BIT(14) */
  74 #define CONFIG_SYS_MAX_NAND_DEVICE      1
  75
  76 /* SPI support */
  77 #define CONFIG_SPI
  78 #define CONFIG_SPI_FLASH
  79 #define CONFIG_SPI_FLASH_STMICRO
  80 #define CONFIG_DAVINCI_SPI
  81 #define CONFIG_SYS_SPI_BASE             DAVINCI_SPI1_BASE
  82 #define CONFIG_SYS_SPI_CLK              davinci_clk_get(SPI_PLLDIV)
  83 #define CONFIG_SF_DEFAULT_SPEED         3000000
  84 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
  85 #define CONFIG_CMD_SF
  86
  87 /* SD/MMC */
  88 #define CONFIG_MMC
  89 #define CONFIG_GENERIC_MMC
  90 #define CONFIG_DAVINCI_MMC
  91 #define CONFIG_MMC_MBLOCK
  92
  93 /* U-Boot command configuration */
  94 #include <config_cmd_default.h>
  95
  96 #define CONFIG_CMD_BDI
  97 #undef CONFIG_CMD_FLASH
  98 #undef CONFIG_CMD_FPGA
  99 #undef CONFIG_CMD_SETGETDCR
 100 #define CONFIG_CMD_ASKENV
 101 #define CONFIG_CMD_CACHE
 102 #define CONFIG_CMD_DHCP
 103 #define CONFIG_CMD_I2C
 104 #define CONFIG_CMD_PING
 105 #define CONFIG_CMD_SAVES
 106
 107 #ifdef CONFIG_CMD_BDI
 108 #define CONFIG_CLOCKS
 109 #endif
 110
 111 #ifdef CONFIG_MMC
 112 #define CONFIG_DOS_PARTITION
 113 #define CONFIG_CMD_EXT2
 114 #define CONFIG_CMD_FAT
 115 #define CONFIG_CMD_MMC
 116 #endif
 117
 118 #ifdef CONFIG_NAND_DAVINCI
 119 #define CONFIG_CMD_MTDPARTS
 120 #define CONFIG_MTD_PARTITIONS
 121 #define CONFIG_MTD_DEVICE
 122 #define CONFIG_CMD_NAND
 123 #define CONFIG_CMD_UBI
 124 #define CONFIG_CMD_UBIFS
 125 #define CONFIG_RBTREE
 126 #define CONFIG_LZO
 127 #endif
 128
 129 #define CONFIG_CRC32_VERIFY
 130 #define CONFIG_MX_CYCLIC
 131
 132 /* U-Boot general configuration */
 133 #define CONFIG_BOOTFILE         "uImage"        /* Boot file name */
 134 #define CONFIG_SYS_PROMPT       "cam_enc_4xx> " /* Monitor Command Prompt */
 135 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size  */
 136 #define CONFIG_SYS_PBSIZE                       /* Print buffer size */ \
 137                 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 138 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 139 #define CONFIG_SYS_HUSH_PARSER
 140 #define CONFIG_SYS_LONGHELP
 141
 142 #define CONFIG_MENU
 143 #define CONFIG_MENU_SHOW
 144 #define CONFIG_FIT
 145 #define CONFIG_BOARD_IMG_ADDR_R 0x80000000
 146
 147 #ifdef CONFIG_NAND_DAVINCI
 148 #define CONFIG_ENV_SIZE                 (16 << 10)
 149 #define CONFIG_ENV_IS_IN_NAND
 150 #define CONFIG_ENV_OFFSET               0x180000
 151 #define CONFIG_ENV_RANGE                0x040000
 152 #define CONFIG_ENV_OFFSET_REDUND        0x1c0000
 153 #undef CONFIG_ENV_IS_IN_FLASH
 154 #endif
 155
 156 #if defined(CONFIG_MMC) && !defined(CONFIG_ENV_IS_IN_NAND)
 157 #define CONFIG_CMD_ENV
 158 #define CONFIG_SYS_MMC_ENV_DEV  0
 159 #define CONFIG_ENV_SIZE         (16 << 10)      /* 16 KiB */
 160 #define CONFIG_ENV_OFFSET       (51 << 9)       /* Sector 51 */
 161 #define CONFIG_ENV_IS_IN_MMC
 162 #undef CONFIG_ENV_IS_IN_FLASH
 163 #endif
 164
 165 #define CONFIG_BOOTDELAY        3
 166 /*
 167  * 24MHz InputClock / 15 prediv -> 1.6 MHz timer running
 168  * Timeout 1 second.
 169  */
 170 #define CONFIG_AIT_TIMER_TIMEOUT        0x186a00
 171
 172 #define CONFIG_CMDLINE_EDITING
 173 #define CONFIG_VERSION_VARIABLE
 174 #define CONFIG_TIMESTAMP
 175
 176 /* U-Boot memory configuration */
 177 #define CONFIG_SYS_MALLOC_LEN           (1 << 20)       /* 1 MiB */
 178 #define CONFIG_SYS_MEMTEST_START        0x80000000      /* physical address */
 179 #define CONFIG_SYS_MEMTEST_END          0x81000000      /* test 16MB RAM */
 180
 181 /* Linux interfacing */
 182 #define CONFIG_CMDLINE_TAG
 183 #define CONFIG_SETUP_MEMORY_TAGS
 184 #define CONFIG_SYS_BARGSIZE     1024                    /* bootarg Size */
 185 #define CONFIG_SYS_LOAD_ADDR    0x80700000              /* kernel address */
 186
 187 #define MTDIDS_DEFAULT          "nand0=davinci_nand.0"
 188 #define MTDPARTS_DEFAULT                        \
 189         "mtdparts="                             \
 190                 "davinci_nand.0:"               \
 191                         "128k(spl),"            \
 192                         "384k(UBLheader),"      \
 193                         "1m(u-boot),"           \
 194                         "512k(env),"            \
 195                         "-(ubi)"
 196
 197 #define CONFIG_SYS_NAND_PAGE_SIZE       0x800
 198 #define CONFIG_SYS_NAND_BLOCK_SIZE      0x20000
 199
 200 /* Defines for SPL */
 201 #define CONFIG_SPL_FRAMEWORK
 202 #define CONFIG_SPL_BOARD_INIT
 203 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 204 #define CONFIG_SPL_NAND_SUPPORT
 205 #define CONFIG_SPL_NAND_BASE
 206 #define CONFIG_SPL_NAND_DRIVERS
 207 #define CONFIG_SPL_NAND_ECC
 208 #define CONFIG_SPL_NAND_SIMPLE
 209 #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
 210 #define CONFIG_SPL_SERIAL_SUPPORT
 211 #define CONFIG_SPL_POST_MEM_SUPPORT
 212 #define CONFIG_SPL_LDSCRIPT             "$(BOARDDIR)/u-boot-spl.lds"
 213 #define CONFIG_SPL_STACK                (0x00010000 + 0x7f00)
 214
 215 #define CONFIG_SPL_TEXT_BASE            0x00000020 /*CONFIG_SYS_SRAM_START*/
 216 /* Provide at least 16MB spacing between us and the Linux Kernel image */
 217 #define CONFIG_SPL_PAD_TO               12320
 218 #define CONFIG_SPL_MAX_FOOTPRINT        12288
 219
 220 #ifndef CONFIG_SPL_BUILD
 221 #define CONFIG_SYS_TEXT_BASE            0x81080000
 222 #endif
 223
 224 #define CONFIG_SYS_NAND_BASE            0x02000000
 225 #define CONFIG_SYS_NAND_PAGE_COUNT      (CONFIG_SYS_NAND_BLOCK_SIZE / \
 226                                         CONFIG_SYS_NAND_PAGE_SIZE)
 227
 228 #define CONFIG_SYS_NAND_ECCPOS          {                               \
 229                                 24, 25, 26, 27, 28,                     \
 230                                 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
 231                                 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
 232                                 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
 233                                 59, 60, 61, 62, 63 }
 234 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
 235 #define CONFIG_SYS_NAND_ECCSIZE         0x200
 236 #define CONFIG_SYS_NAND_ECCBYTES        10
 237 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 238 #define CONFIG_SYS_NAND_MAX_ECCPOS      56
 239 #define CONFIG_SYS_NAND_OOBSIZE         64
 240 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 241
 242 /*
 243  * RBL searches from Block n (n = 1..24)
 244  * so we can define, how many UBL Headers
 245  * we can write before the real spl code
 246  */
 247 #define CONFIG_SYS_NROF_PAGES_NAND_SPL  6
 248
 249 #define CONFIG_SYS_NAND_U_BOOT_DST      0x81080000 /* u-boot TEXT_BASE */
 250 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_NAND_U_BOOT_DST
 251
 252 /*
 253  * Post tests for memory testing
 254  */
 255 #define CONFIG_POST     CONFIG_SYS_POST_MEMORY
 256 #define _POST_WORD_ADDR 0x0
 257
 258 #define CONFIG_DISPLAY_BOARDINFO
 259
 260 #define CONFIG_SYS_INIT_SP_ADDR         CONFIG_SPL_STACK
 261
 262 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 263 #define CONFIG_SYS_NAND_U_BOOT_SIZE     0xa0000
 264 #define CONFIG_SYS_NAND_U_BOOT_ERA_SIZE 0x100000
 265
 266 /* for UBL header */
 267 #define CONFIG_SYS_UBL_BLOCK            (CONFIG_SYS_NAND_PAGE_SIZE)
 268
 269 #define CONFIG_SYS_DM36x_PLL1_PLLM      0x55
 270 #define CONFIG_SYS_DM36x_PLL1_PREDIV    0x8005
 271 #define CONFIG_SYS_DM36x_PLL2_PLLM      0x09
 272 #define CONFIG_SYS_DM36x_PLL2_PREDIV    0x8000
 273 #define CONFIG_SYS_DM36x_PERI_CLK_CTRL  0x243F04FC
 274 #define CONFIG_SYS_DM36x_PLL1_PLLDIV1   0x801b
 275 #define CONFIG_SYS_DM36x_PLL1_PLLDIV2   0x8001
 276 /* POST DIV 680/2 = 340Mhz  -> MJCP and HDVICP bus interface clock */
 277 #define CONFIG_SYS_DM36x_PLL1_PLLDIV3   0x8001
 278 /*
 279  * POST DIV 680/4 = 170Mhz  -> EDMA/Peripheral CFG0(1/2 MJCP/HDVICP bus
 280  * interface clk)
 281  */
 282 #define CONFIG_SYS_DM36x_PLL1_PLLDIV4   0x8003
 283 /* POST DIV 680/2 = 340Mhz  -> VPSS */
 284 #define CONFIG_SYS_DM36x_PLL1_PLLDIV5   0x8001
 285 /* POST DIV 680/9 = 75.6 Mhz -> VENC */
 286 #define CONFIG_SYS_DM36x_PLL1_PLLDIV6   0x8008
 287 /*
 288  * POST DIV 680/1 = 680Mhz -> DDRx2(with internal divider of 2, clock boils
 289  * down to 340 Mhz)
 290  */
 291 #define CONFIG_SYS_DM36x_PLL1_PLLDIV7   0x8000
 292 /* POST DIV 680/7= 97Mhz-> MMC0/SD0 */
 293 #define CONFIG_SYS_DM36x_PLL1_PLLDIV8   0x8006
 294 /* POST DIV 680/28 = 24.3Mhz-> CLKOUT */
 295 #define CONFIG_SYS_DM36x_PLL1_PLLDIV9   0x801b
 296
 297 #define CONFIG_SYS_DM36x_PLL2_PLLDIV1   0x8011
 298 /* POST DIV 432/1=432 Mhz  -> ARM926/(HDVICP block) clk */
 299 #define CONFIG_SYS_DM36x_PLL2_PLLDIV2   0x8000
 300 #define CONFIG_SYS_DM36x_PLL2_PLLDIV3   0x8001
 301 /* POST DIV 432/21= 20.5714 Mhz->VOICE Codec clk */
 302 #define CONFIG_SYS_DM36x_PLL2_PLLDIV4   0x8014
 303 /* POST DIV 432/16=27 Mhz  -> VENC(For SD modes, requires) */
 304 #define CONFIG_SYS_DM36x_PLL2_PLLDIV5   0x800f
 305
 306 /*
 307  * READ LATENCY 7 (CL + 2)
 308  * CONFIG_PWRDNEN = 1
 309  * CONFIG_EXT_STRBEN = 1
 310  */
 311 #define CONFIG_SYS_DM36x_DDR2_DDRPHYCR  (0 \
 312         | DV_DDR_PHY_EXT_STRBEN \
 313         | DV_DDR_PHY_PWRDNEN \
 314         | (7 << DV_DDR_PHY_RD_LATENCY_SHIFT))
 315
 316 /*
 317  * T_RFC = (trfc/DDR_CLK) - 1 = (195 / 2.941) - 1
 318  * T_RP  = (trp/DDR_CLK) - 1  = (12.5 / 2.941) - 1
 319  * T_RCD = (trcd/DDR_CLK) - 1 = (12.5 / 2.941) - 1
 320  * T_WR  = (twr/DDR_CLK) - 1  = (15 / 2.941) - 1
 321  * T_RAS = (tras/DDR_CLK) - 1 = (45 / 2.941) - 1
 322  * T_RC  = (trc/DDR_CLK) - 1  = (57.5 / 2.941) - 1
 323  * T_RRD = (trrd/DDR_CLK) - 1 = (7.5 / 2.941) - 1
 324  * T_WTR = (twtr/DDR_CLK) - 1 = (7.5 / 2.941) - 1
 325  */
 326 #define CONFIG_SYS_DM36x_DDR2_SDTIMR    (0 \
 327         | (66 << DV_DDR_SDTMR1_RFC_SHIFT) \
 328         | (4  << DV_DDR_SDTMR1_RP_SHIFT) \
 329         | (4  << DV_DDR_SDTMR1_RCD_SHIFT) \
 330         | (5  << DV_DDR_SDTMR1_WR_SHIFT) \
 331         | (14 << DV_DDR_SDTMR1_RAS_SHIFT) \
 332         | (19 << DV_DDR_SDTMR1_RC_SHIFT) \
 333         | (2  << DV_DDR_SDTMR1_RRD_SHIFT) \
 334         | (2  << DV_DDR_SDTMR1_WTR_SHIFT))
 335
 336 /*
 337  * T_RASMAX = (trasmax/refresh_rate) - 1 = (70K / 7812.6) - 1
 338  * T_XP  = tCKE - 1 = 3 - 2
 339  * T_XSNR= ((trfc + 10)/DDR_CLK) - 1 = (205 / 2.941) - 1
 340  * T_XSRD = txsrd - 1 = 200 - 1
 341  * T_RTP = (trtp/DDR_CLK) - 1 = (7.5 / 2.941) - 1
 342  * T_CKE = tcke - 1     = 3 - 1
 343  */
 344 #define CONFIG_SYS_DM36x_DDR2_SDTIMR2   (0 \
 345         | (8  << DV_DDR_SDTMR2_RASMAX_SHIFT) \
 346         | (2  << DV_DDR_SDTMR2_XP_SHIFT) \
 347         | (69 << DV_DDR_SDTMR2_XSNR_SHIFT) \
 348         | (199 <<  DV_DDR_SDTMR2_XSRD_SHIFT) \
 349         | (2 <<  DV_DDR_SDTMR2_RTP_SHIFT) \
 350         | (2 <<  DV_DDR_SDTMR2_CKE_SHIFT))
 351
 352 /* PR_OLD_COUNT = 0xfe */
 353 #define CONFIG_SYS_DM36x_DDR2_PBBPR     0x000000FE
 354 /* refresh rate = 0x768 */
 355 #define CONFIG_SYS_DM36x_DDR2_SDRCR     0x00000768
 356
 357 #define CONFIG_SYS_DM36x_DDR2_SDBCR     (0 \
 358         | (2 << DV_DDR_SDCR_PAGESIZE_SHIFT) \
 359         | (3 << DV_DDR_SDCR_IBANK_SHIFT) \
 360         | (5 << DV_DDR_SDCR_CL_SHIFT) \
 361         | (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT)    \
 362         | (1 << DV_DDR_SDCR_TIMUNLOCK_SHIFT) \
 363         | (1 << DV_DDR_SDCR_DDREN_SHIFT) \
 364         | (0 << DV_DDR_SDCR_DDRDRIVE0_SHIFT)    \
 365         | (1 << DV_DDR_SDCR_DDR2EN_SHIFT) \
 366         | (1 << DV_DDR_SDCR_DDR_DDQS_SHIFT) \
 367         | (1 << DV_DDR_SDCR_BOOTUNLOCK_SHIFT))
 368
 369 #define CONFIG_SYS_DM36x_AWCCR  0xff
 370 #define CONFIG_SYS_DM36x_AB1CR  0x40400204
 371 #define CONFIG_SYS_DM36x_AB2CR  0x04ca2650
 372
 373 /* All Video Inputs */
 374 #define CONFIG_SYS_DM36x_PINMUX0        0x00000000
 375 /*
 376  * All Video Outputs,
 377  * GPIO 86, 87 + 90 0x0000f030
 378  */
 379 #define CONFIG_SYS_DM36x_PINMUX1        0x00530002
 380 #define CONFIG_SYS_DM36x_PINMUX2        0x00001815
 381 /*
 382  * SPI1, UART1, I2C, SD0, SD1, McBSP0, CLKOUTs
 383  * GPIO 25 0x60000000
 384  */
 385 #define CONFIG_SYS_DM36x_PINMUX3        0x9b5affff
 386 /*
 387  * MMC/SD0 instead of MS, SPI0
 388  * GPIO 34 0x0000c000
 389  */
 390 #define CONFIG_SYS_DM36x_PINMUX4        0x00002655
 391
 392 /*
 393  * Default environment settings
 394  */
 395
 396 #define DVN4XX_UBOOT_ADDR_R_RAM         0x80000000
 397 /* (DVN4XX_UBOOT_ADDR_R_RAM + CONFIG_SYS_NAND_PAGE_SIZE) */
 398 #define DVN4XX_UBOOT_ADDR_R_NAND_SPL    0x80000800
 399 /*
 400  * (DVN4XX_UBOOT_ADDR_R_NAND_SPL + (CONFIG_SYS_NROF_PAGES_NAND_SPL * \
 401  * CONFIG_SYS_NAND_PAGE_SIZE))
 402  */
 403 #define DVN4XX_UBOOT_ADDR_R_UBOOT       0x80003800
 404
 405 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 406         "u_boot_addr_r=" __stringify(DVN4XX_UBOOT_ADDR_R_RAM) "\0"      \
 407         "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.ubl\0"          \
 408         "load=tftp ${u_boot_addr_r} ${u-boot}\0"                        \
 409         "pagesz=" __stringify(CONFIG_SYS_NAND_PAGE_SIZE) "\0"           \
 410         "writeheader=nandrbl rbl;nand erase 20000 ${pagesz};"           \
 411                 "nand write ${u_boot_addr_r} 20000 ${pagesz};"          \
 412                 "nandrbl uboot\0"                                       \
 413         "writenand_spl=nandrbl rbl;nand erase 0 3000;"                  \
 414                 "nand write " __stringify(DVN4XX_UBOOT_ADDR_R_NAND_SPL) \
 415                 " 0 3000;nandrbl uboot\0"                               \
 416         "writeuboot=nandrbl uboot;"                                     \
 417                 "nand erase " __stringify(CONFIG_SYS_NAND_U_BOOT_OFFS) " "\
 418                  __stringify(CONFIG_SYS_NAND_U_BOOT_ERA_SIZE)           \
 419                 ";nand write " __stringify(DVN4XX_UBOOT_ADDR_R_UBOOT)   \
 420                 " " __stringify(CONFIG_SYS_NAND_U_BOOT_OFFS) " "        \
 421                 __stringify(CONFIG_SYS_NAND_U_BOOT_SIZE) "\0"           \
 422         "update=run load writenand_spl writeuboot\0"                    \
 423         "bootcmd=run net_nfs\0"                                         \
 424         "rootpath=/opt/eldk-arm/arm\0"                                  \
 425         "mtdids=" MTDIDS_DEFAULT "\0"                                   \
 426         "mtdparts=" MTDPARTS_DEFAULT "\0"                               \
 427         "netdev=eth0\0"                                                 \
 428         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 429         "addmisc=setenv bootargs ${bootargs} app_reset=${app_reset}\0"  \
 430         "addcon=setenv bootargs ${bootargs} console=ttyS0,"             \
 431                 "${baudrate}n8\0"                                       \
 432         "addip=setenv bootargs ${bootargs} "                            \
 433                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 434                 ":${hostname}:${netdev}:off eth=${ethaddr} panic=1\0"   \
 435         "rootpath=/opt/eldk-arm/arm\0"                                  \
 436         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 437                 "nfsroot=${serverip}:${rootpath}\0"                     \
 438         "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage \0"           \
 439         "kernel_addr_r=80600000\0"                                      \
 440         "load_kernel=tftp ${kernel_addr_r} ${bootfile}\0"               \
 441         "ubi_load_kernel=ubi part ubi 2048;ubifsmount ubi:${img_volume};" \
 442                 "ubifsload ${kernel_addr_r} boot/uImage\0"              \
 443         "fit_addr_r=" __stringify(CONFIG_BOARD_IMG_ADDR_R) "\0"         \
 444         "img_addr_r=" __stringify(CONFIG_BOARD_IMG_ADDR_R) "\0"         \
 445         "img_file=" __stringify(CONFIG_HOSTNAME) "/ait.itb\0"           \
 446         "header_addr=20000\0"                                           \
 447         "img_writeheader=nandrbl rbl;"                                  \
 448                 "nand erase ${header_addr} ${pagesz};"                  \
 449                 "nand write ${img_addr_r} ${header_addr} ${pagesz};"    \
 450                 "nandrbl uboot\0"                                       \
 451         "img_writespl=nandrbl rbl;nand erase 0 3000;"                   \
 452                 "nand write ${img_addr_r} 0 3000;nandrbl uboot\0"       \
 453         "img_writeuboot=nandrbl uboot;"                                 \
 454                 "nand erase " __stringify(CONFIG_SYS_NAND_U_BOOT_OFFS) " "\
 455                  __stringify(CONFIG_SYS_NAND_U_BOOT_ERA_SIZE)           \
 456                 ";nand write ${img_addr_r} "                            \
 457                 __stringify(CONFIG_SYS_NAND_U_BOOT_OFFS) " "            \
 458                 __stringify(CONFIG_SYS_NAND_U_BOOT_SIZE) "\0"           \
 459         "img_writedfenv=ubi part ubi 2048;"                             \
 460                 "ubi write ${img_addr_r} default ${filesize}\0"         \
 461         "img_volume=rootfs1\0"                                          \
 462         "img_writeramdisk=ubi part ubi 2048;"                           \
 463                 "ubi write ${img_addr_r} ${img_volume} ${filesize}\0"   \
 464         "load_img=tftp ${fit_addr_r} ${img_file}\0"                     \
 465         "net_nfs=run load_kernel; "                                     \
 466                 "run nfsargs addip addcon addmtd addmisc;"              \
 467                 "bootm ${kernel_addr_r}\0"                              \
 468         "ubi_ubi=run ubi_load_kernel; "                                 \
 469                 "run ubiargs addip addcon addmtd addmisc;"              \
 470                 "bootm ${kernel_addr_r}\0"                              \
 471         "ubiargs=setenv bootargs ubi.mtd=4,2048"                        \
 472                 " root=ubi0:${img_volume} rw rootfstype=ubifs\0"        \
 473         "app_reset=no\0"                                                \
 474         "dvn_app_vers=void\0"                                           \
 475         "dvn_boot_vers=void\0"                                          \
 476         "savenewvers=run savetmpparms restoreparms; saveenv;"           \
 477                 "run restoretmpparms\0"                                 \
 478         "savetmpparms=setenv y_ipaddr ${ipaddr};"                       \
 479                 "setenv y_netmask ${netmask};"                          \
 480                 "setenv y_serverip ${serverip};"                        \
 481                 "setenv y_gatewayip ${gatewayip}\0"                     \
 482         "saveparms=setenv x_ipaddr ${ipaddr};"                          \
 483                 "setenv x_netmask ${netmask};"                          \
 484                 "setenv x_serverip ${serverip};"                        \
 485                 "setenv x_gatewayip ${gatewayip}\0"                     \
 486         "restoreparms=setenv ipaddr ${x_ipaddr};"                       \
 487                 "setenv netmask ${x_netmask};"                          \
 488                 "setenv serverip ${x_serverip};"                        \
 489                 "setenv gatewayip ${x_gatewayip}\0"                     \
 490         "restoretmpparms=setenv ipaddr ${y_ipaddr};"                    \
 491                 "setenv netmask ${y_netmask};"                          \
 492                 "setenv serverip ${y_serverip};"                        \
 493                 "setenv gatewayip ${y_gatewayip}\0"                     \
 494         "\0"
 495
 496 /* USB Configuration */
 497 #define CONFIG_USB_DAVINCI
 498 #define CONFIG_MUSB_HCD
 499 #define CONFIG_DV_USBPHY_CTL (USBPHY_SESNDEN | USBPHY_VBDTCTEN | \
 500                                 USBPHY_PHY24MHZ)
 501
 502 #define CONFIG_CMD_USB         /* include support for usb cmd */
 503 #define CONFIG_USB_STORAGE     /* MSC class support */
 504 #define CONFIG_CMD_STORAGE     /* inclue support for usb-storage cmd */
 505 #define CONFIG_CMD_FAT         /* inclue support for FAT/storage */
 506 #define CONFIG_DOS_PARTITION   /* inclue support for FAT/storage */
 507
 508 #undef DAVINCI_DM365EVM
 509 #define PINMUX4_USBDRVBUS_BITCLEAR       0x3000
 510 #define PINMUX4_USBDRVBUS_BITSET         0x2000
 511
 512 #endif /* __CONFIG_H */