include/configs/km/kmp204x-common.h

   1 /*
   2  * (C) Copyright 2013 Keymile AG
   3  * Valentin Longchamp <valentin.longchamp@keymile.com>
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef _CONFIG_KMP204X_H
   9 #define _CONFIG_KMP204X_H
  10
  11 #define CONFIG_PHYS_64BIT
  12 #define CONFIG_PPC_P2041
  13
  14 #define CONFIG_SYS_TEXT_BASE    0xfff80000
  15
  16 #define CONFIG_KM_DEF_NETDEV    "netdev=eth0\0"
  17
  18 #define CONFIG_NAND_ECC_BCH
  19
  20 /* common KM defines */
  21 #include "keymile-common.h"
  22
  23 #define CONFIG_SYS_RAMBOOT
  24 #define CONFIG_RAMBOOT_PBL
  25 #define CONFIG_RAMBOOT_TEXT_BASE        CONFIG_SYS_TEXT_BASE
  26 #define CONFIG_RESET_VECTOR_ADDRESS     0xfffffffc
  27 #define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/keymile/kmp204x/pbi.cfg
  28 #define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/keymile/kmp204x/rcw_kmp204x.cfg
  29
  30 /* High Level Configuration Options */
  31 #define CONFIG_BOOKE
  32 #define CONFIG_E500                     /* BOOKE e500 family */
  33 #define CONFIG_E500MC                   /* BOOKE e500mc family */
  34 #define CONFIG_SYS_BOOK3E_HV            /* Category E.HV supported */
  35 #define CONFIG_MPC85xx                  /* MPC85xx/PQ3 platform */
  36 #define CONFIG_FSL_CORENET              /* Freescale CoreNet platform */
  37 #define CONFIG_MP                       /* support multiple processors */
  38
  39 #define CONFIG_SYS_FSL_CPC              /* Corenet Platform Cache */
  40 #define CONFIG_SYS_NUM_CPC              CONFIG_NUM_DDR_CONTROLLERS
  41 #define CONFIG_FSL_ELBC                 /* Has Enhanced localbus controller */
  42 #define CONFIG_PCI                      /* Enable PCI/PCIE */
  43 #define CONFIG_PCIE1                    /* PCIE controler 1 */
  44 #define CONFIG_PCIE3                    /* PCIE controler 3 */
  45 #define CONFIG_FSL_PCI_INIT             /* Use common FSL init code */
  46 #define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */
  47
  48 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
  49
  50 #define CONFIG_FSL_LAW                  /* Use common FSL init code */
  51
  52 /* Environment in SPI Flash */
  53 #define CONFIG_SYS_EXTRA_ENV_RELOC
  54 #define CONFIG_ENV_IS_IN_SPI_FLASH
  55 #define CONFIG_ENV_SPI_BUS              0
  56 #define CONFIG_ENV_SPI_CS               0
  57 #define CONFIG_ENV_SPI_MAX_HZ           20000000
  58 #define CONFIG_ENV_SPI_MODE             0
  59 #define CONFIG_ENV_OFFSET               0x100000        /* 1MB for u-boot */
  60 #define CONFIG_ENV_SIZE                 0x004000        /* 16K env */
  61 #define CONFIG_ENV_SECT_SIZE            0x010000
  62 #define CONFIG_ENV_OFFSET_REDUND        0x110000
  63 #define CONFIG_ENV_TOTAL_SIZE           0x020000
  64
  65 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  66
  67 #ifndef __ASSEMBLY__
  68 unsigned long get_board_sys_clk(unsigned long dummy);
  69 #endif
  70 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
  71
  72 /*
  73  * These can be toggled for performance analysis, otherwise use default.
  74  */
  75 #define CONFIG_SYS_CACHE_STASHING
  76 #define CONFIG_BACKSIDE_L2_CACHE
  77 #define CONFIG_SYS_INIT_L2CSR0          L2CSR0_L2E
  78 #define CONFIG_BTB                      /* toggle branch predition */
  79
  80 #define CONFIG_ENABLE_36BIT_PHYS
  81
  82 #define CONFIG_ADDR_MAP
  83 #define CONFIG_SYS_NUM_ADDR_MAP         64      /* number of TLB1 entries */
  84
  85 #define CONFIG_POST CONFIG_SYS_POST_MEMORY      /* test POST memory test */
  86 #define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest works on */
  87 #define CONFIG_SYS_MEMTEST_END          0x00800000
  88 #define CONFIG_SYS_ALT_MEMTEST
  89 #define CONFIG_PANIC_HANG       /* do not reset board on panic */
  90
  91 /*
  92  *  Config the L3 Cache as L3 SRAM
  93  */
  94 #define CONFIG_SYS_INIT_L3_ADDR         CONFIG_RAMBOOT_TEXT_BASE
  95 #define CONFIG_SYS_INIT_L3_ADDR_PHYS    (0xf00000000ull | \
  96                 CONFIG_RAMBOOT_TEXT_BASE)
  97 #define CONFIG_SYS_L3_SIZE              (1024 << 10)
  98 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
  99
 100 #define CONFIG_SYS_DCSRBAR              0xf0000000
 101 #define CONFIG_SYS_DCSRBAR_PHYS         0xf00000000ull
 102
 103 /*
 104  * DDR Setup
 105  */
 106 #define CONFIG_VERY_BIG_RAM
 107 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 108 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 109
 110 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 111 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 112
 113 #define CONFIG_DDR_SPD
 114 #define CONFIG_SYS_FSL_DDR3
 115 #define CONFIG_FSL_DDR_INTERACTIVE
 116
 117 #define CONFIG_SYS_SPD_BUS_NUM  0
 118 #define SPD_EEPROM_ADDRESS      0x54
 119 #define CONFIG_SYS_SDRAM_SIZE   4096    /* for fixed parameter use */
 120
 121 #define CONFIG_SYS_LOAD_ADDR    0x100000        /* default load address */
 122 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
 123
 124 /******************************************************************************
 125  * (PRAM usage)
 126  * ... -------------------------------------------------------
 127  * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM
 128  * ... |<------------------- pram -------------------------->|
 129  * ... -------------------------------------------------------
 130  * @END_OF_RAM:
 131  * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
 132  * @CONFIG_KM_PHRAM: address for /var
 133  * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
 134  * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
 135  */
 136
 137 /* size of rootfs in RAM */
 138 #define CONFIG_KM_ROOTFSSIZE    0x0
 139 /* pseudo-non volatile RAM [hex] */
 140 #define CONFIG_KM_PNVRAM        0x80000
 141 /* physical RAM MTD size [hex] */
 142 #define CONFIG_KM_PHRAM         0x100000
 143 /* resereved pram area at the end of memroy [hex] */
 144 #define CONFIG_KM_RESERVED_PRAM 0x0
 145 /* enable protected RAM */
 146 #define CONFIG_PRAM             0
 147
 148 #define CONFIG_KM_CRAMFS_ADDR   0x2000000
 149 #define CONFIG_KM_KERNEL_ADDR   0x1000000       /* max kernel size 15.5Mbytes */
 150 #define CONFIG_KM_FDT_ADDR      0x1F80000       /* max dtb    size  0.5Mbytes */
 151
 152 #define CONFIG_BOOTCOUNT_LIMIT
 153
 154 /*
 155  * Local Bus Definitions
 156  */
 157
 158 /* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */
 159 #define CONFIG_SYS_LBC_LCRR             (LCRR_CLKDIV_8 | LCRR_EADC_2)
 160
 161 /* Nand Flash */
 162 #define CONFIG_NAND_FSL_ELBC
 163 #define CONFIG_SYS_NAND_BASE            0xffa00000
 164 #define CONFIG_SYS_NAND_BASE_PHYS       0xfffa00000ull
 165
 166 #define CONFIG_SYS_NAND_BASE_LIST     {CONFIG_SYS_NAND_BASE}
 167 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 168 #define CONFIG_MTD_NAND_VERIFY_WRITE
 169 #define CONFIG_CMD_NAND
 170 #define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)
 171
 172 #define CONFIG_BCH
 173
 174 /* NAND flash config */
 175 #define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 176                                | BR_PS_8               /* Port Size = 8 bit */ \
 177                                | BR_MS_FCM             /* MSEL = FCM */ \
 178                                | BR_V)                 /* valid */
 179
 180 #define CONFIG_SYS_NAND_OR_PRELIM  (OR_AM_256KB       /* length 256K */ \
 181                                | OR_FCM_BCTLD   /* LBCTL not ass */     \
 182                                | OR_FCM_SCY_1   /* 1 clk wait cycle */  \
 183                                | OR_FCM_RST     /* 1 clk read setup */  \
 184                                | OR_FCM_PGS     /* Large page size */   \
 185                                | OR_FCM_CST)    /* 0.25 command setup */
 186
 187 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
 188 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 189
 190 /* QRIO FPGA */
 191 #define CONFIG_SYS_QRIO_BASE            0xfb000000
 192 #define CONFIG_SYS_QRIO_BASE_PHYS       0xffb000000ull
 193
 194 #define CONFIG_SYS_QRIO_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \
 195                                 | BR_PS_8       /* Port Size 8 bits */ \
 196                                 | BR_DECC_OFF   /* no error corr */ \
 197                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 198                                 | BR_V)         /* valid */
 199
 200 #define CONFIG_SYS_QRIO_OR_PRELIM  (OR_AM_64KB  /* length 64K */ \
 201                                 | OR_GPCM_BCTLD /* no LCTL assert */ \
 202                                 | OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \
 203                                 | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
 204                                 | OR_GPCM_TRLX /* relaxed tmgs */ \
 205                                 | OR_GPCM_EAD) /* extra bus clk cycles */
 206
 207 #define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
 208 #define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */
 209
 210 #define CONFIG_BOARD_EARLY_INIT_F
 211 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 212 #define CONFIG_MISC_INIT_R
 213 #define CONFIG_LAST_STAGE_INIT
 214
 215 #define CONFIG_HWCONFIG
 216
 217 /* define to use L1 as initial stack */
 218 #define CONFIG_L1_INIT_RAM
 219 #define CONFIG_SYS_INIT_RAM_LOCK
 220 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000      /* Initial L1 address */
 221 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
 222 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
 223 /* The assembler doesn't like typecast */
 224 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 225         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 226           CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 227 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 228
 229 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 230                                         GENERATED_GBL_DATA_SIZE)
 231 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 232
 233 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
 234 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)
 235 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)
 236
 237 /* Serial Port - controlled on board with jumper J8
 238  * open - index 2
 239  * shorted - index 1
 240  */
 241 #define CONFIG_CONS_INDEX       1
 242 #define CONFIG_SYS_NS16550
 243 #define CONFIG_SYS_NS16550_SERIAL
 244 #define CONFIG_SYS_NS16550_REG_SIZE     1
 245 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 246
 247 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 248 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 249 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 250 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 251
 252 #define CONFIG_KM_CONSOLE_TTY   "ttyS0"
 253
 254 /* Use the HUSH parser */
 255 #define CONFIG_SYS_HUSH_PARSER
 256
 257 /* pass open firmware flat tree */
 258 #define CONFIG_OF_LIBFDT
 259 #define CONFIG_OF_BOARD_SETUP
 260 #define CONFIG_OF_STDOUT_VIA_ALIAS
 261
 262 /* new uImage format support */
 263 #define CONFIG_FIT
 264 #define CONFIG_FIT_VERBOSE      /* enable fit_format_{error,warning}() */
 265
 266 /* I2C */
 267 #define CONFIG_SYS_I2C
 268 #define CONFIG_SYS_NUM_I2C_BUSES        3
 269 #define CONFIG_SYS_I2C_MAX_HOPS         1
 270 #define CONFIG_SYS_I2C_FSL              /* Use FSL I2C driver */
 271 #define CONFIG_I2C_MULTI_BUS
 272 #define CONFIG_I2C_CMD_TREE
 273 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 274 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 275 #define CONFIG_SYS_FSL_I2C_OFFSET       0x118000
 276 #define CONFIG_SYS_I2C_BUSES    {       {0, {I2C_NULL_HOP} }, \
 277                                         {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
 278                                         {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
 279                                 }
 280
 281 #define CONFIG_KM_IVM_BUS               1       /* I2C1 (Mux-Port 1)*/
 282
 283 /*
 284  * eSPI - Enhanced SPI
 285  */
 286 #define CONFIG_FSL_ESPI
 287 #define CONFIG_SPI_FLASH
 288 #define CONFIG_SPI_FLASH_BAR    /* 4 byte-addressing */
 289 #define CONFIG_SPI_FLASH_STMICRO
 290 #define CONFIG_CMD_SF
 291 #define CONFIG_SF_DEFAULT_SPEED         20000000
 292 #define CONFIG_SF_DEFAULT_MODE          0
 293
 294 /*
 295  * General PCI
 296  * Memory space is mapped 1-1, but I/O space must start from 0.
 297  */
 298
 299 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 300 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 301 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 302 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 303 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 304 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 305 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 306 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 307 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 308
 309 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 310 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xa0000000
 311 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 312 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc20000000ull
 313 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x20000000      /* 512M */
 314 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8010000
 315 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 316 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8010000ull
 317 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 318
 319 /* Qman/Bman */
 320 #define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
 321 #define CONFIG_SYS_BMAN_NUM_PORTALS     10
 322 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 323 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 324 #define CONFIG_SYS_BMAN_MEM_SIZE        0x00200000
 325 #define CONFIG_SYS_QMAN_NUM_PORTALS     10
 326 #define CONFIG_SYS_QMAN_MEM_BASE        0xf4200000
 327 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff4200000ull
 328 #define CONFIG_SYS_QMAN_MEM_SIZE        0x00200000
 329
 330 #define CONFIG_SYS_DPAA_FMAN
 331 #define CONFIG_SYS_DPAA_PME
 332 /* Default address of microcode for the Linux Fman driver
 333  * env is stored at 0x100000, sector size is 0x10000, x2 (redundant)
 334  * ucode is stored after env, so we got 0x120000.
 335  */
 336 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 337 #define CONFIG_SYS_QE_FMAN_FW_ADDR      0x120000
 338 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 339 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 340
 341 #define CONFIG_FMAN_ENET
 342 #define CONFIG_PHYLIB_10G
 343 #define CONFIG_PHY_MARVELL              /* there is a marvell phy */
 344
 345 #define CONFIG_PCI_INDIRECT_BRIDGE
 346 #define CONFIG_PCI_PNP                  /* do pci plug-and-play */
 347 #define CONFIG_E1000
 348
 349 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 350 #define CONFIG_DOS_PARTITION
 351
 352 /* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */
 353 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR  0x11
 354 #define CONFIG_SYS_TBIPA_VALUE  8
 355 #define CONFIG_PHYLIB           /* recommended PHY management */
 356 #define CONFIG_ETHPRIME         "FM1@DTSEC5"
 357 #define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
 358
 359 /*
 360  * Environment
 361  */
 362 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 363 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 364
 365 /*
 366  * additionnal command line configuration.
 367  */
 368 #define CONFIG_CMD_PCI
 369 #define CONFIG_CMD_NET
 370
 371 /* we don't need flash support */
 372 #define CONFIG_SYS_NO_FLASH
 373 #undef CONFIG_CMD_IMLS
 374 #undef CONFIG_CMD_FLASH
 375 #undef CONFIG_FLASH_CFI_MTD
 376 #undef CONFIG_JFFS2_CMDLINE
 377
 378 /*
 379  * For booting Linux, the board info and command line data
 380  * have to be in the first 64 MB of memory, since this is
 381  * the maximum mapped by the Linux kernel during initialization.
 382  */
 383 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux */
 384 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 385
 386 #ifdef CONFIG_CMD_KGDB
 387 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 388 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 389 #endif
 390
 391 #define __USB_PHY_TYPE  utmi
 392
 393 /*
 394  * Environment Configuration
 395  */
 396 #define CONFIG_ENV_OVERWRITE
 397 #ifndef CONFIG_KM_DEF_ENV               /* if not set by keymile-common.h */
 398 #define CONFIG_KM_DEF_ENV "km-common=empty\0"
 399 #endif
 400
 401 #ifndef MTDIDS_DEFAULT
 402 # define MTDIDS_DEFAULT         "nand0=fsl_elbc_nand"
 403 #endif /* MTDIDS_DEFAULT */
 404
 405 #ifndef MTDPARTS_DEFAULT
 406 # define MTDPARTS_DEFAULT       "mtdparts="                     \
 407         "fsl_elbc_nand:"                                                \
 408                 "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");"
 409 #endif /* MTDPARTS_DEFAULT */
 410
 411 /* architecture specific default bootargs */
 412 #define CONFIG_KM_DEF_BOOT_ARGS_CPU             ""
 413
 414 /* FIXME: FDT_ADDR is unspecified */
 415 #define CONFIG_KM_DEF_ENV_CPU                                           \
 416         "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0"                   \
 417         "cramfsloadfdt="                                                \
 418                 "cramfsload ${fdt_addr_r} "                             \
 419                 "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0"             \
 420         "fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0"              \
 421         "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0"           \
 422         "update="                                                       \
 423                 "sf probe 0;sf erase 0 +${filesize};"                   \
 424                 "sf write ${load_addr_r} 0 ${filesize};\0"              \
 425         ""
 426
 427 #define CONFIG_HW_ENV_SETTINGS                                          \
 428         "hwconfig=fsl_ddr:ctlr_intlv=cacheline\0"                       \
 429         "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0"                \
 430         "usb_dr_mode=host\0"
 431
 432 #define CONFIG_KM_NEW_ENV                                               \
 433         "newenv=sf probe 0;"                                            \
 434                 "sf erase " __stringify(CONFIG_ENV_OFFSET) " "          \
 435                 __stringify(CONFIG_ENV_TOTAL_SIZE)"\0"
 436
 437 /* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */
 438 #ifndef CONFIG_KM_DEF_ARCH
 439 #define CONFIG_KM_DEF_ARCH      "arch=ppc_82xx\0"
 440 #endif
 441
 442 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 443         CONFIG_KM_DEF_ENV                                               \
 444         CONFIG_KM_DEF_ARCH                                              \
 445         CONFIG_KM_NEW_ENV                                               \
 446         CONFIG_HW_ENV_SETTINGS                                          \
 447         "EEprom_ivm=pca9547:70:9\0"                                     \
 448         ""
 449
 450 #endif /* _CONFIG_KMP204X_H */