include/configs/uniphier.h

   1 /*
   2  * Copyright (C) 2012-2015 Masahiro Yamada <yamada.masahiro@socionext.com>
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /* U-boot - Common settings for UniPhier Family */
   8
   9 #ifndef __CONFIG_UNIPHIER_COMMON_H__
  10 #define __CONFIG_UNIPHIER_COMMON_H__
  11
  12 #if defined(CONFIG_MACH_PH1_SLD3)
  13 #define CONFIG_DDR_NUM_CH0 2
  14 #define CONFIG_DDR_NUM_CH1 1
  15 #define CONFIG_DDR_NUM_CH2 1
  16
  17 /* Physical start address of SDRAM */
  18 #define CONFIG_SDRAM0_BASE      0x80000000
  19 #define CONFIG_SDRAM0_SIZE      0x20000000
  20 #define CONFIG_SDRAM1_BASE      0xc0000000
  21 #define CONFIG_SDRAM1_SIZE      0x20000000
  22 #define CONFIG_SDRAM2_BASE      0xc0000000
  23 #define CONFIG_SDRAM2_SIZE      0x10000000
  24 #endif
  25
  26 #if defined(CONFIG_MACH_PH1_LD4)
  27 #define CONFIG_DDR_NUM_CH0 1
  28 #define CONFIG_DDR_NUM_CH1 1
  29
  30 /* Physical start address of SDRAM */
  31 #define CONFIG_SDRAM0_BASE      0x80000000
  32 #define CONFIG_SDRAM0_SIZE      0x10000000
  33 #define CONFIG_SDRAM1_BASE      0x90000000
  34 #define CONFIG_SDRAM1_SIZE      0x10000000
  35 #endif
  36
  37 #if defined(CONFIG_MACH_PH1_PRO4)
  38 #define CONFIG_DDR_NUM_CH0 2
  39 #define CONFIG_DDR_NUM_CH1 2
  40
  41 /* Physical start address of SDRAM */
  42 #define CONFIG_SDRAM0_BASE      0x80000000
  43 #define CONFIG_SDRAM0_SIZE      0x20000000
  44 #define CONFIG_SDRAM1_BASE      0xa0000000
  45 #define CONFIG_SDRAM1_SIZE      0x20000000
  46 #endif
  47
  48 #if defined(CONFIG_MACH_PH1_SLD8)
  49 #define CONFIG_DDR_NUM_CH0 1
  50 #define CONFIG_DDR_NUM_CH1 1
  51
  52 /* Physical start address of SDRAM */
  53 #define CONFIG_SDRAM0_BASE      0x80000000
  54 #define CONFIG_SDRAM0_SIZE      0x10000000
  55 #define CONFIG_SDRAM1_BASE      0x90000000
  56 #define CONFIG_SDRAM1_SIZE      0x10000000
  57 #endif
  58
  59 #define CONFIG_I2C_EEPROM
  60 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  10
  61
  62 /*
  63  * Support card address map
  64  */
  65 #if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
  66 # define CONFIG_SUPPORT_CARD_BASE       0x03f00000
  67 # define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
  68 # define CONFIG_SUPPORT_CARD_LED_BASE   (CONFIG_SUPPORT_CARD_BASE + 0x00090000)
  69 # define CONFIG_SUPPORT_CARD_UART_BASE  (CONFIG_SUPPORT_CARD_BASE + 0x000b0000)
  70 #endif
  71
  72 #if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
  73 # define CONFIG_SUPPORT_CARD_BASE       0x08000000
  74 # define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
  75 # define CONFIG_SUPPORT_CARD_LED_BASE   (CONFIG_SUPPORT_CARD_BASE + 0x00401630)
  76 # define CONFIG_SUPPORT_CARD_UART_BASE  (CONFIG_SUPPORT_CARD_BASE + 0x00200000)
  77 #endif
  78
  79 #ifdef CONFIG_SYS_NS16550_SERIAL
  80 #define CONFIG_SYS_NS16550
  81 #define CONFIG_SYS_NS16550_COM1         CONFIG_SUPPORT_CARD_UART_BASE
  82 #define CONFIG_SYS_NS16550_CLK          12288000
  83 #define CONFIG_SYS_NS16550_REG_SIZE     -2
  84 #endif
  85
  86 /* TODO: move to Kconfig and device tree */
  87 #if 0
  88 #define CONFIG_SYS_NS16550_SERIAL
  89 #endif
  90
  91 #define CONFIG_SMC911X
  92
  93 #define CONFIG_SMC911X_BASE             CONFIG_SUPPORT_CARD_ETHER_BASE
  94 #define CONFIG_SMC911X_32_BIT
  95
  96 /*-----------------------------------------------------------------------
  97  * MMU and Cache Setting
  98  *----------------------------------------------------------------------*/
  99
 100 /* Comment out the following to enable L1 cache */
 101 /* #define CONFIG_SYS_ICACHE_OFF */
 102 /* #define CONFIG_SYS_DCACHE_OFF */
 103
 104 #define CONFIG_SYS_CACHELINE_SIZE       32
 105
 106 /* Comment out the following to enable L2 cache */
 107 #define CONFIG_UNIPHIER_L2CACHE_ON
 108
 109 #define CONFIG_DISPLAY_CPUINFO
 110 #define CONFIG_DISPLAY_BOARDINFO
 111 #define CONFIG_MISC_INIT_F
 112 #define CONFIG_BOARD_EARLY_INIT_F
 113 #define CONFIG_BOARD_EARLY_INIT_R
 114 #define CONFIG_BOARD_LATE_INIT
 115
 116 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 117
 118 #define CONFIG_TIMESTAMP
 119
 120 /* FLASH related */
 121 #define CONFIG_MTD_DEVICE
 122
 123 /*
 124  * uncomment the following to disable FLASH related code.
 125  */
 126 /* #define CONFIG_SYS_NO_FLASH */
 127
 128 #define CONFIG_FLASH_CFI_DRIVER
 129 #define CONFIG_SYS_FLASH_CFI
 130
 131 #define CONFIG_SYS_MAX_FLASH_SECT       256
 132 #define CONFIG_SYS_MONITOR_BASE         0
 133 #define CONFIG_SYS_FLASH_BASE           0
 134
 135 /*
 136  * flash_toggle does not work for out supoort card.
 137  * We need to use flash_status_poll.
 138  */
 139 #define CONFIG_SYS_CFI_FLASH_STATUS_POLL
 140
 141 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 142
 143 #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2
 144
 145 /* serial console configuration */
 146 #define CONFIG_BAUDRATE                 115200
 147
 148 #define CONFIG_SYS_GENERIC_BOARD
 149
 150 #if !defined(CONFIG_SPL_BUILD)
 151 #define CONFIG_USE_ARCH_MEMSET
 152 #define CONFIG_USE_ARCH_MEMCPY
 153 #endif
 154
 155 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 156
 157 #define CONFIG_CMDLINE_EDITING          /* add command line history     */
 158 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size */
 159 /* Print Buffer Size */
 160 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 161 #define CONFIG_SYS_MAXARGS              16      /* max number of command */
 162 /* Boot Argument Buffer Size */
 163 #define CONFIG_SYS_BARGSIZE             (CONFIG_SYS_CBSIZE)
 164
 165 #define CONFIG_CONS_INDEX               1
 166
 167 /*
 168  * For NAND booting the environment is embedded in the U-Boot image. Please take
 169  * look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
 170  */
 171 /* #define CONFIG_ENV_IS_IN_NAND */
 172 #define CONFIG_ENV_IS_NOWHERE
 173 #define CONFIG_ENV_SIZE                         0x2000
 174 #define CONFIG_ENV_OFFSET                       0x0
 175 /* #define CONFIG_ENV_OFFSET_REDUND     (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */
 176
 177 /* Time clock 1MHz */
 178 #define CONFIG_SYS_TIMER_RATE                   1000000
 179
 180 /*
 181  * By default, ARP timeout is 5 sec.
 182  * The first ARP request does not seem to work.
 183  * So we need to retry ARP request anyway.
 184  * We want to shrink the interval until the second ARP request.
 185  */
 186 #define CONFIG_ARP_TIMEOUT      500UL  /* 0.5 msec */
 187
 188 #define CONFIG_SYS_MAX_NAND_DEVICE                      1
 189 #define CONFIG_SYS_NAND_MAX_CHIPS                       2
 190 #define CONFIG_SYS_NAND_ONFI_DETECTION
 191
 192 #define CONFIG_NAND_DENALI_ECC_SIZE                     1024
 193
 194 #ifdef CONFIG_MACH_PH1_SLD3
 195 #define CONFIG_SYS_NAND_REGS_BASE                       0xf8100000
 196 #define CONFIG_SYS_NAND_DATA_BASE                       0xf8000000
 197 #else
 198 #define CONFIG_SYS_NAND_REGS_BASE                       0x68100000
 199 #define CONFIG_SYS_NAND_DATA_BASE                       0x68000000
 200 #endif
 201
 202 #define CONFIG_SYS_NAND_BASE            (CONFIG_SYS_NAND_DATA_BASE + 0x10)
 203
 204 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 205 #define CONFIG_SYS_NAND_BAD_BLOCK_POS                   0
 206
 207 /* USB */
 208 #define CONFIG_USB_MAX_CONTROLLER_COUNT         2
 209 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      4
 210 #define CONFIG_CMD_FAT
 211 #define CONFIG_FAT_WRITE
 212 #define CONFIG_DOS_PARTITION
 213
 214 /* memtest works on */
 215 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE
 216 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_SDRAM_BASE + 0x01000000)
 217
 218 #define CONFIG_BOOTDELAY                        3
 219 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
 220
 221 /*
 222  * Network Configuration
 223  */
 224 #define CONFIG_SERVERIP                 192.168.11.1
 225 #define CONFIG_IPADDR                   192.168.11.10
 226 #define CONFIG_GATEWAYIP                192.168.11.1
 227 #define CONFIG_NETMASK                  255.255.255.0
 228
 229 #define CONFIG_LOADADDR                 0x84000000
 230 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 231
 232 #define CONFIG_CMDLINE_EDITING          /* add command line history     */
 233
 234 #define CONFIG_BOOTCOMMAND              "run $bootmode"
 235
 236 #define CONFIG_ROOTPATH                 "/nfs/root/path"
 237 #define CONFIG_NFSBOOTCOMMAND                                           \
 238         "setenv bootargs $bootargs root=/dev/nfs rw "                   \
 239         "nfsroot=$serverip:$rootpath "                                  \
 240         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
 241         "tftpboot; bootm;"
 242
 243 #define CONFIG_BOOTARGS         " earlyprintk loglevel=8"
 244
 245 #ifdef CONFIG_FIT
 246 #define CONFIG_BOOTFILE                 "fitImage"
 247 #define LINUXBOOT_ENV_SETTINGS \
 248         "fit_addr=0x00100000\0" \
 249         "fit_addr_r=0x84100000\0" \
 250         "fit_size=0x00f00000\0" \
 251         "norboot=run add_default_bootargs &&" \
 252                 "bootm $fit_addr\0" \
 253         "nandboot=run add_default_bootargs &&" \
 254                 "nand read $fit_addr_r $fit_addr $fit_size &&" \
 255                 "bootm $fit_addr_r\0" \
 256         "tftpboot=run add_default_bootargs &&" \
 257                 "tftpboot $fit_addr_r $bootfile &&" \
 258                 "bootm $fit_addr_r\0"
 259 #else
 260 #define CONFIG_BOOTFILE                 "uImage"
 261 #define LINUXBOOT_ENV_SETTINGS \
 262         "fdt_addr=0x00100000\0" \
 263         "fdt_addr_r=0x84100000\0" \
 264         "fdt_size=0x00008000\0" \
 265         "fdt_file=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
 266         "kernel_addr=0x00200000\0" \
 267         "kernel_addr_r=0x84200000\0" \
 268         "kernel_size=0x00800000\0" \
 269         "ramdisk_addr=0x00a00000\0" \
 270         "ramdisk_addr_r=0x84a00000\0" \
 271         "ramdisk_size=0x00600000\0" \
 272         "ramdisk_file=rootfs.cpio.uboot\0" \
 273         "norboot=run add_default_bootargs &&" \
 274                 "bootm $kernel_addr $ramdisk_addr $fdt_addr\0" \
 275         "nandboot=run add_default_bootargs &&" \
 276                 "nand read $kernel_addr_r $kernel_addr $kernel_size &&" \
 277                 "nand read $ramdisk_addr_r $ramdisk_addr $ramdisk_size &&" \
 278                 "nand read $fdt_addr_r $fdt_addr $fdt_size &&" \
 279                 "bootm $kernel_addr_r $ramdisk_addr_r $fdt_addr_r\0" \
 280         "tftpboot=run add_default_bootargs &&" \
 281                 "tftpboot $kernel_addr_r $bootfile &&" \
 282                 "tftpboot $ramdisk_addr_r $ramdisk_file &&" \
 283                 "tftpboot $fdt_addr_r $fdt_file &&" \
 284                 "bootm $kernel_addr_r $ramdisk_addr_r $fdt_addr_r\0"
 285 #endif
 286
 287 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 288         "netdev=eth0\0"                                         \
 289         "verify=n\0"                                            \
 290         "nandupdate=nand erase 0 0x00100000 &&"                 \
 291                 "tftpboot u-boot-spl-dtb.bin &&"                \
 292                 "nand write $loadaddr 0 0x00010000 &&"          \
 293                 "tftpboot u-boot-dtb.img &&"                    \
 294                 "nand write $loadaddr 0x00010000 0x000f0000\0"  \
 295         "add_default_bootargs=setenv bootargs $bootargs"        \
 296                 " console=ttyS0,$baudrate\0"                    \
 297         LINUXBOOT_ENV_SETTINGS
 298
 299 /* Open Firmware flat tree */
 300 #define CONFIG_OF_LIBFDT
 301
 302 /* Memory Size & Mapping */
 303 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SDRAM0_BASE
 304
 305 #if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE >= CONFIG_SDRAM1_BASE
 306 /* Thre is no memory hole */
 307 #define CONFIG_NR_DRAM_BANKS            1
 308 #define CONFIG_SYS_SDRAM_SIZE   (CONFIG_SDRAM0_SIZE + CONFIG_SDRAM1_SIZE)
 309 #else
 310 #define CONFIG_NR_DRAM_BANKS            2
 311 #define CONFIG_SYS_SDRAM_SIZE   (CONFIG_SDRAM0_SIZE)
 312 #endif
 313
 314 #if defined(CONFIG_MACH_PH1_SLD3) || defined(CONFIG_MACH_PH1_LD4) || \
 315         defined(CONFIG_MACH_PH1_SLD8)
 316 #define CONFIG_SPL_TEXT_BASE            0x00040000
 317 #endif
 318 #if defined(CONFIG_MACH_PH1_PRO4)
 319 #define CONFIG_SPL_TEXT_BASE            0x00100000
 320 #endif
 321
 322 #define CONFIG_SPL_STACK                (0x0ff08000)
 323 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_TEXT_BASE)
 324
 325 #define CONFIG_PANIC_HANG
 326
 327 #define CONFIG_SPL_FRAMEWORK
 328 #define CONFIG_SPL_SERIAL_SUPPORT
 329 #define CONFIG_SPL_NAND_SUPPORT
 330
 331 #define CONFIG_SPL_LIBCOMMON_SUPPORT    /* for mem_malloc_init */
 332 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 333
 334 #define CONFIG_SPL_BOARD_INIT
 335
 336 #define CONFIG_SYS_NAND_U_BOOT_OFFS             0x10000
 337
 338 #define CONFIG_SPL_MAX_FOOTPRINT                0x10000
 339
 340 #endif /* __CONFIG_UNIPHIER_COMMON_H__ */