# # (C) Copyright 2009 # Marvell Semiconductor # Written-by: Prafulla Wadaskar # # adopted to TK71 by # Nils Faerber # # See file CREDITS for list of people who contributed to this # project. # # This program is free software; you can redistribute it and/or # modify it under the terms of the GNU General Public License as # published by the Free Software Foundation; either version 2 of # the License, or (at your option) any later version. # # This program is distributed in the hope that it will be useful, # but WITHOUT ANY WARRANTY; without even the implied warranty of # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the # GNU General Public License for more details. # # You should have received a copy of the GNU General Public License # along with this program; if not, write to the Free Software # Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, # MA 02110-1301 USA # # Refer docs/README.kwimage for more details about how-to configure # and create kirkwood boot image # # Boot Media configurations BOOT_FROM nand NAND_ECC_MODE default NAND_PAGE_SIZE 0x0800 # SOC registers configuration using bootrom header extension # Maximum KWBIMAGE_MAX_CONFIG configurations allowed # Configure RGMII-0 interface pad voltage to 1.8V DATA 0xFFD100e0 0x1b1b1b9b #Dram initalization for SINGLE x16 CL=5 @ 400MHz DATA 0xFFD01400 0x43000c30 # DDR Configuration register # bit13-0: 0xc30 (3120 DDR2 clks refresh rate) # bit23-14: zero # bit24: 1= enable exit self refresh mode on DDR access # bit25: 1 required # bit29-26: zero # bit31-30: 01 DATA 0xFFD01404 0x36543000 # DDR Controller Control Low # bit 4: 0=addr/cmd in smame cycle # bit 5: 0=clk is driven during self refresh, we don't care for APX # bit 6: 0=use recommended falling edge of clk for addr/cmd # bit14: 0=input buffer always powered up # bit18: 1=cpu lock transaction enabled # bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 # bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM # bit30-28: 3 required # bit31: 0=no additional STARTBURST delay DATA 0xFFD01408 0x1101355b # DDR Timing (Low) (active cycles value +1) # bit3-0: TRAS lsbs # bit7-4: TRCD # bit11- 8: TRP # bit15-12: TWR # bit19-16: TWTR # bit20: TRAS msb # bit23-21: 0x0 # bit27-24: TRRD # bit31-28: TRTP DATA 0xFFD0140C 0x00000034 # DDR Timing (High) # bit6-0: TRFC # bit8-7: TR2R # bit10-9: TR2W # bit12-11: TW2W # bit31-13: zero required DATA 0xFFD01410 0x00000000 # DDR Address Control # bit1-0: 01, Cs0width=x16 # bit3-2: 10, Cs0size=512Mb # bit5-4: 01, Cs1width=x16 # bit7-6: 10, Cs1size=512Mb # bit9-8: 00, Cs2width=nonexistent # bit11-10: 00, Cs2size =nonexistent # bit13-12: 00, Cs3width=nonexistent # bit15-14: 00, Cs3size =nonexistent # bit16: 0, Cs0AddrSel # bit17: 0, Cs1AddrSel # bit18: 0, Cs2AddrSel # bit19: 0, Cs3AddrSel # bit31-20: 0 required DATA 0xFFD01414 0x00000000 # DDR Open Pages Control # bit0: 0, OpenPage enabled # bit31-1: 0 required DATA 0xFFD01418 0x00000000 # DDR Operation # bit3-0: 0x0, DDR cmd # bit31-4: 0 required DATA 0xFFD0141C 0x00000652 # DDR Mode # bit2-0: 2, BurstLen=2 required # bit3: 0, BurstType=0 required # bit6-4: 4, CL=5 # bit7: 0, TestMode=0 normal # bit8: 0, DLL reset=0 normal # bit11-9: 6, auto-precharge write recovery ???????????? # bit12: 0, PD must be zero # bit31-13: 0 required DATA 0xFFD01420 0x00000042 # DDR Extended Mode # bit0: 0, DDR DLL enabled # bit1: 0, DDR drive strenght normal # bit2: 0, DDR ODT control lsd (disabled) # bit5-3: 000, required # bit6: 1, DDR ODT control msb, (disabled) # bit9-7: 000, required # bit10: 0, differential DQS enabled # bit11: 0, required # bit12: 0, DDR output buffer enabled # bit31-13: 0 required DATA 0xFFD01424 0x0000F17F # DDR Controller Control High # bit2-0: 111, required # bit3 : 1 , MBUS Burst Chop disabled # bit6-4: 111, required # bit7 : 0 # bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz # bit9 : 0 , no half clock cycle addition to dataout # bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals # bit11 : 0 , 1/4 clock cycle skew disabled for write mesh # bit15-12: 1111 required # bit31-16: 0 required DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 DATA 0xFFD01504 0x1FFFFFF1 # CS[0]n Size # bit0: 1, Window enabled # bit1: 0, Write Protect disabled # bit3-2: 00, CS0 hit selected # bit23-4: ones, required # bit31-24: 0x0F, Size (i.e. 256MB) DATA 0xFFD01508 0x00000000 # CS[1]n Base address to 256Mb DATA 0xFFD0150C 0x00000000 # CS[1]n Size 256Mb Window enabled for CS1 DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled DATA 0xFFD01494 0x00110000 # DDR ODT Control (Low) # bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1 # bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0 # bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1. # bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0. DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) # bit1-0: 00, ODT0 controlled by ODT Control (low) register above # bit3-2: 01, ODT1 active NEVER! # bit31-4: zero, required DATA 0xFFD0149C 0x0000F80F # CPU ODT Control # bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3 # bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm # bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm # bit14: 1, M_STARTBURST_IN ODT: Enabled # bit15: 1, DDR IO ODT Unit: Use ODT block DATA 0xFFD01480 0x00000001 # DDR Initialization Control #bit0=1, enable DDR init upon this register write # End of Header extension DATA 0x0 0x0