/s3c24x0 Files specific to Samsung S3C24X0 CPUs
/arm926ejs Files specific to ARM 926 CPUs
/arm1136 Files specific to ARM 1136 CPUs
- /ixp Files specific to Intel XScale IXP CPUs
/pxa Files specific to Intel XScale PXA CPUs
/sa1100 Files specific to Intel StrongARM SA1100 CPUs
/lib Architecture specific library files
Board config to use DDR3. It can be enabled for SoCs with
Freescale DDR3 controllers.
+ CONFIG_SYS_FSL_IFC_BE
+ Defines the IFC controller register space as Big Endian
+
+ CONFIG_SYS_FSL_IFC_LE
+ Defines the IFC controller register space as Little Endian
+
CONFIG_SYS_FSL_PBL_PBI
It enables addition of RCW (Power on reset configuration) in built image.
Please refer doc/README.pblimage for more details
PBI commands can be used to configure SoC before it starts the execution.
Please refer doc/README.pblimage for more details
+ CONFIG_SYS_FSL_DDR_BE
+ Defines the DDR controller register space as Big Endian
+
+ CONFIG_SYS_FSL_DDR_LE
+ Defines the DDR controller register space as Little Endian
+
+ CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY
+ Physical address from the view of DDR controllers. It is the
+ same as CONFIG_SYS_DDR_SDRAM_BASE for all Power SoCs. But
+ it could be different for ARM SoCs.
+
+ CONFIG_SYS_FSL_DDR_INTLV_256B
+ DDR controller interleaving on 256-byte. This is a special
+ interleaving mode, handled by Dickens for Freescale layerscape
+ SoCs with ARM core.
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
CONFIG_CMD_BSP * Board specific commands
CONFIG_CMD_BOOTD bootd
CONFIG_CMD_CACHE * icache, dcache
+ CONFIG_CMD_CLK * clock command support
CONFIG_CMD_CONSOLE coninfo
CONFIG_CMD_CRC32 * crc32
CONFIG_CMD_DATE * support for RTC, date/time...
CONFIG_CMD_EXPORTENV * export the environment
CONFIG_CMD_EXT2 * ext2 command support
CONFIG_CMD_EXT4 * ext4 command support
+ CONFIG_CMD_FS_GENERIC * filesystem commands (e.g. load, ls)
+ that work for multiple fs types
CONFIG_CMD_SAVEENV saveenv
CONFIG_CMD_FDC * Floppy Disk Support
CONFIG_CMD_FAT * FAT command support
- CONFIG_CMD_FDOS * Dos diskette Support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
CONFIG_CMD_FUSE * Device fuse support
If this option is set, then U-Boot will prevent the environment
variable "splashimage" from being set to a problematic address
- (see README.displaying-bmps and README.arm-unaligned-accesses).
+ (see README.displaying-bmps).
This option is useful for targets where, due to alignment
restrictions, an improperly aligned BMP image will cause a data
abort. If you think you will not have problems with unaligned
CONFIG_RSA
This enables the RSA algorithm used for FIT image verification
- in U-Boot. See doc/uImage/signature for more information.
+ in U-Boot. See doc/uImage.FIT/signature.txt for more information.
The signing part is build into mkimage regardless of this
option.
+- bootcount support:
+ CONFIG_BOOTCOUNT_LIMIT
+
+ This enables the bootcounter support, see:
+ http://www.denx.de/wiki/DULG/UBootBootCountLimit
+
+ CONFIG_AT91SAM9XE
+ enable special bootcounter support on at91sam9xe based boards.
+ CONFIG_BLACKFIN
+ enable special bootcounter support on blackfin based boards.
+ CONFIG_SOC_DA8XX
+ enable special bootcounter support on da850 based boards.
+ CONFIG_BOOTCOUNT_RAM
+ enable support for the bootcounter in RAM
+ CONFIG_BOOTCOUNT_I2C
+ enable support for the bootcounter on an i2c (like RTC) device.
+ CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
+ CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
+ the bootcounter.
+ CONFIG_BOOTCOUNT_ALEN = address len
- Show boot progress:
CONFIG_SHOW_BOOT_PROGRESS
Configuration Settings:
-----------------------
+- CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
+ Optionally it can be defined to support 64-bit memory commands.
+
- CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
undefine this when you're short of memory.
its config.mk file). If you find problems enabling this option on
your board please report the problem and send patches!
-- CONFIG_SYS_SYM_OFFSETS
- This is set by architectures that use offsets for link symbols
- instead of absolute values. So bss_start is obtained using an
- offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
- directly. You should not need to touch this setting.
-
- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
This is set by OMAP boards for the max time that reset should
be asserted. See doc/README.omap-reset-time for details on how
projects / karo-tx-uboot.git / blobdiff