snapper9260: remove unused AT91_LEGACY

[karo-tx-uboot.git] / README

diff --git a/README b/README
index e209c89e215f7ca419cfa84b9c450a103532e628..f0ffaf491cd9c204b24a49aacf4d9712148cdf32 100644 (file)
--- a/README
+++ b/README
@@ -705,6 +705,11 @@ The following options need to be configured:
                the "silent" environment variable. See
                doc/README.silent for more information.
 
+               CONFIG_SYS_CONSOLE_BG_COL: define the backgroundcolor, default
+                       is 0x00.
+               CONFIG_SYS_CONSOLE_FG_COL: define the foregroundcolor, default
+                       is 0xa0.
+
 - Console Baudrate:
                CONFIG_BAUDRATE - in bps
                Select one of the baudrates listed in
@@ -779,6 +784,22 @@ The following options need to be configured:
                as a convenience, when switching between booting from
                RAM and NFS.
 
+- Bootcount:
+               CONFIG_BOOTCOUNT_LIMIT
+               Implements a mechanism for detecting a repeating reboot
+               cycle, see:
+               http://www.denx.de/wiki/view/DULG/UBootBootCountLimit
+
+               CONFIG_BOOTCOUNT_ENV
+               If no softreset save registers are found on the hardware
+               "bootcount" is stored in the environment. To prevent a
+               saveenv on all reboots, the environment variable
+               "upgrade_available" is used. If "upgrade_available" is
+               0, "bootcount" is always 0, if "upgrade_available" is
+               1 "bootcount" is incremented in the environment.
+               So the Userspace Applikation must set the "upgrade_available"
+               and "bootcount" variable to 0, if a boot was successfully.
+
 - Pre-Boot Commands:
                CONFIG_PREBOOT
 
@@ -843,6 +864,7 @@ The following options need to be configured:
                CONFIG_CMD_ELF          * bootelf, bootvx
                CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
                CONFIG_CMD_ENV_FLAGS    * display details about env flags
+               CONFIG_CMD_ENV_EXISTS   * check existence of env variable
                CONFIG_CMD_EXPORTENV    * export the environment
                CONFIG_CMD_EXT2         * ext2 command support
                CONFIG_CMD_EXT4         * ext4 command support
@@ -1027,7 +1049,6 @@ The following options need to be configured:
 
 - GPIO Support:
                CONFIG_PCA953X          - use NXP's PCA953X series I2C GPIO
-               CONFIG_PCA953X_INFO     - enable pca953x info command
 
                The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
                chip-ngpio pairs that tell the PCA953X driver the number of
@@ -1362,6 +1383,13 @@ The following options need to be configured:
                        for your device
                        - CONFIG_USBD_PRODUCTID 0xFFFF
 
+               Some USB device drivers may need to check USB cable attachment.
+               In this case you can enable following config in BoardName.h:
+                       CONFIG_USB_CABLE_CHECK
+                       This enables function definition:
+                       - usb_cable_connected() in include/usb.h
+                       Implementation of this function is board-specific.
+
 - ULPI Layer Support:
                The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
                the generic ULPI layer. The generic layer accesses the ULPI PHY
@@ -1994,9 +2022,9 @@ CBFS (Coreboot Filesystem) support
                    second bus.
 
                - drivers/i2c/tegra_i2c.c:
-                - activate this driver with CONFIG_SYS_I2C_TEGRA
-                - This driver adds 4 i2c buses with a fix speed from
-                  100000 and the slave addr 0!
+                 - activate this driver with CONFIG_SYS_I2C_TEGRA
+                 - This driver adds 4 i2c buses with a fix speed from
+                   100000 and the slave addr 0!
 
                - drivers/i2c/ppc4xx_i2c.c
                  - activate this driver with CONFIG_SYS_I2C_PPC4XX
@@ -4291,6 +4319,9 @@ Low Level (hardware related) configuration options:
 
                NOTE : currently only supported on AM335x platforms.
 
+- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
+               Enables the RTC32K OSC on AM33xx based plattforms
+
 Freescale QE/FMAN Firmware Support:
 -----------------------------------