}
#endif
+#ifdef CONFIG_NAND_MXS
+void setup_gpmi_io_clk(u32 cfg)
+{
+ /* Disable clocks per ERR007177 from MX6 errata */
+ clrbits_le32(&imx_ccm->CCGR4,
+ MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+
+ clrbits_le32(&imx_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+
+ clrsetbits_le32(&imx_ccm->cs2cdr,
+ MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
+ MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
+ MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
+ cfg);
+
+ setbits_le32(&imx_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+ setbits_le32(&imx_ccm->CCGR4,
+ MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+}
+#endif
+
void enable_usboh3_clk(unsigned char enable)
{
u32 reg;
}
+#if defined(CONFIG_FEC_MXC) && !defined(CONFIG_MX6SX)
+void enable_enet_clk(unsigned char enable)
+{
+ u32 mask = MXC_CCM_CCGR1_ENET_CLK_ENABLE_MASK;
+
+ if (enable)
+ setbits_le32(&imx_ccm->CCGR1, mask);
+ else
+ clrbits_le32(&imx_ccm->CCGR1, mask);
+}
+#endif
+
+#ifdef CONFIG_MXC_UART
+void enable_uart_clk(unsigned char enable)
+{
+ u32 mask = MXC_CCM_CCGR5_UART_MASK | MXC_CCM_CCGR5_UART_SERIAL_MASK;
+
+ if (enable)
+ setbits_le32(&imx_ccm->CCGR5, mask);
+ else
+ clrbits_le32(&imx_ccm->CCGR5, mask);
+}
+#endif
+
+#ifdef CONFIG_SPI
+/* spi_num can be from 0 - 4 */
+int enable_cspi_clock(unsigned char enable, unsigned spi_num)
+{
+ u32 mask;
+
+ if (spi_num > 4)
+ return -EINVAL;
+
+ mask = MXC_CCM_CCGR_CG_MASK << (spi_num * 2);
+ if (enable)
+ setbits_le32(&imx_ccm->CCGR1, mask);
+ else
+ clrbits_le32(&imx_ccm->CCGR1, mask);
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_MMC
+int enable_usdhc_clk(unsigned char enable, unsigned bus_num)
+{
+ u32 mask;
+
+ if (bus_num > 3)
+ return -EINVAL;
+
+ mask = MXC_CCM_CCGR_CG_MASK << (bus_num * 2 + 2);
+ if (enable)
+ setbits_le32(&imx_ccm->CCGR6, mask);
+ else
+ clrbits_le32(&imx_ccm->CCGR6, mask);
+
+ return 0;
+}
+#endif
+
#ifdef CONFIG_SYS_I2C_MXC
/* i2c_num can be from 0 - 2 */
int enable_i2c_clk(unsigned char enable, unsigned i2c_num)
}
#endif
+/* spi_num can be from 0 - SPI_MAX_NUM */
+int enable_spi_clk(unsigned char enable, unsigned spi_num)
+{
+ u32 reg;
+ u32 mask;
+
+ if (spi_num > SPI_MAX_NUM)
+ return -EINVAL;
+
+ mask = MXC_CCM_CCGR_CG_MASK << (spi_num << 1);
+ reg = __raw_readl(&imx_ccm->CCGR1);
+ if (enable)
+ reg |= mask;
+ else
+ reg &= ~mask;
+ __raw_writel(reg, &imx_ccm->CCGR1);
+ return 0;
+}
static u32 decode_pll(enum pll_clocks pll, u32 infreq)
{
u32 div;
div = __raw_readl(&imx_ccm->analog_pll_sys);
div &= BM_ANADIG_PLL_SYS_DIV_SELECT;
- return infreq * (div >> 1);
+ return (infreq * div) >> 1;
case PLL_BUS:
div = __raw_readl(&imx_ccm->analog_pll_528);
div &= BM_ANADIG_PLL_528_DIV_SELECT;
u32 reg, uart_podf;
u32 freq = decode_pll(PLL_USBOTG, MXC_HCLK) / 6; /* static divider */
reg = __raw_readl(&imx_ccm->cscdr1);
-#ifdef CONFIG_MX6SL
+#if (defined(CONFIG_MX6SL) || defined(CONFIG_MX6SX))
if (reg & MXC_CCM_CSCDR1_UART_CLK_SEL)
freq = MXC_HCLK;
#endif
return root_freq / (emi_slow_podf + 1);
}
-#ifdef CONFIG_MX6SL
+#if (defined(CONFIG_MX6SL) || defined(CONFIG_MX6SX))
static u32 get_mmdc_ch0_clk(void)
{
u32 cbcmr = __raw_readl(&imx_ccm->cbcmr);
reg &= ~BM_ANADIG_PLL_ENET_BYPASS;
writel(reg, &anatop->pll_enet);
+#ifdef CONFIG_MX6SX
+ /*
+ * Set enet ahb clock to 200MHz
+ * pll2_pfd2_396m-> ENET_PODF-> ENET_AHB
+ */
+ reg = readl(&imx_ccm->chsccdr);
+ reg &= ~(MXC_CCM_CHSCCDR_ENET_PRE_CLK_SEL_MASK
+ | MXC_CCM_CHSCCDR_ENET_PODF_MASK
+ | MXC_CCM_CHSCCDR_ENET_CLK_SEL_MASK);
+ /* PLL2 PFD2 */
+ reg |= (4 << MXC_CCM_CHSCCDR_ENET_PRE_CLK_SEL_OFFSET);
+ /* Div = 2*/
+ reg |= (1 << MXC_CCM_CHSCCDR_ENET_PODF_OFFSET);
+ reg |= (0 << MXC_CCM_CHSCCDR_ENET_CLK_SEL_OFFSET);
+ writel(reg, &imx_ccm->chsccdr);
+
+ /* Enable enet system clock */
+ reg = readl(&imx_ccm->CCGR3);
+ reg |= MXC_CCM_CCGR3_ENET_MASK;
+ writel(reg, &imx_ccm->CCGR3);
+#endif
return 0;
}
#endif
u32 imx_get_fecclk(void)
{
- return decode_pll(PLL_ENET, MXC_HCLK);
+ return mxc_get_clock(MXC_IPG_CLK);
}
static int enable_enet_pll(uint32_t en)
return 0;
}
+#ifndef CONFIG_MX6SX
static void ungate_sata_clock(void)
{
struct mxc_ccm_reg *const imx_ccm =
/* Enable SATA clock. */
setbits_le32(&imx_ccm->CCGR5, MXC_CCM_CCGR5_SATA_MASK);
}
+#endif
static void ungate_pcie_clock(void)
{
setbits_le32(&imx_ccm->CCGR4, MXC_CCM_CCGR4_PCIE_MASK);
}
+#ifndef CONFIG_MX6SX
int enable_sata_clock(void)
{
ungate_sata_clock();
return enable_enet_pll(BM_ANADIG_PLL_ENET_ENABLE_SATA);
}
+#endif
int enable_pcie_clock(void)
{
struct anatop_regs *anatop_regs =
(struct anatop_regs *)ANATOP_BASE_ADDR;
struct mxc_ccm_reg *ccm_regs = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ u32 lvds1_clk_sel;
/*
* Here be dragons!
* marked as ANATOP_MISC1 is actually documented in the PMU section
* of the datasheet as PMU_MISC1.
*
- * Switch LVDS clock source to SATA (0xb), disable clock INPUT and
- * enable clock OUTPUT. This is important for PCI express link that
- * is clocked from the i.MX6.
+ * Switch LVDS clock source to SATA (0xb) on mx6q/dl or PCI (0xa) on
+ * mx6sx, disable clock INPUT and enable clock OUTPUT. This is important
+ * for PCI express link that is clocked from the i.MX6.
*/
#define ANADIG_ANA_MISC1_LVDSCLK1_IBEN (1 << 12)
#define ANADIG_ANA_MISC1_LVDSCLK1_OBEN (1 << 10)
#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK 0x0000001F
+#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_PCIE_REF 0xa
+#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_SATA_REF 0xb
+
+ if (is_cpu_type(MXC_CPU_MX6SX))
+ lvds1_clk_sel = ANADIG_ANA_MISC1_LVDS1_CLK_SEL_PCIE_REF;
+ else
+ lvds1_clk_sel = ANADIG_ANA_MISC1_LVDS1_CLK_SEL_SATA_REF;
+
clrsetbits_le32(&anatop_regs->ana_misc1,
ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
- ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xb);
+ ANADIG_ANA_MISC1_LVDSCLK1_OBEN | lvds1_clk_sel);
/* PCIe reference clock sourced from AXI. */
clrbits_le32(&ccm_regs->cbcmr, MXC_CCM_CBCMR_PCIE_AXI_CLK_SEL);
/* Party time! Ungate the clock to the PCIe. */
+#ifndef CONFIG_MX6SX
ungate_sata_clock();
+#endif
ungate_pcie_clock();
return enable_enet_pll(BM_ANADIG_PLL_ENET_ENABLE_SATA |
BM_ANADIG_PLL_ENET_ENABLE_PCIE);
}
+#ifdef CONFIG_SECURE_BOOT
+void hab_caam_clock_enable(unsigned char enable)
+{
+ u32 reg;
+
+ /* CG4 ~ CG6, CAAM clocks */
+ reg = __raw_readl(&imx_ccm->CCGR0);
+ if (enable)
+ reg |= (MXC_CCM_CCGR0_CAAM_WRAPPER_IPG_MASK |
+ MXC_CCM_CCGR0_CAAM_WRAPPER_ACLK_MASK |
+ MXC_CCM_CCGR0_CAAM_SECURE_MEM_MASK);
+ else
+ reg &= ~(MXC_CCM_CCGR0_CAAM_WRAPPER_IPG_MASK |
+ MXC_CCM_CCGR0_CAAM_WRAPPER_ACLK_MASK |
+ MXC_CCM_CCGR0_CAAM_SECURE_MEM_MASK);
+ __raw_writel(reg, &imx_ccm->CCGR0);
+
+ /* EMI slow clk */
+ reg = __raw_readl(&imx_ccm->CCGR6);
+ if (enable)
+ reg |= MXC_CCM_CCGR6_EMI_SLOW_MASK;
+ else
+ reg &= ~MXC_CCM_CCGR6_EMI_SLOW_MASK;
+ __raw_writel(reg, &imx_ccm->CCGR6);
+}
+#endif
+
unsigned int mxc_get_clock(enum mxc_clock clk)
{
switch (clk) {
return 0;
}
+#ifndef CONFIG_MX6SX
void enable_ipu_clock(void)
{
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
reg |= MXC_CCM_CCGR3_IPU1_IPU_MASK;
writel(reg, &mxc_ccm->CCGR3);
}
+#endif
/***************************************************/
U_BOOT_CMD(
projects / karo-tx-uboot.git / blobdiff