+ struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ u32 mask480;
+ u32 mask528;
+ u32 reg, periph1, periph2;
+
+ if (is_cpu_type(MXC_CPU_MX6SX))
+ return;
+
+ /* Due to hardware limitation, on MX6Q we need to gate/ungate all PFDs
+ * to make sure PFD is working right, otherwise, PFDs may
+ * not output clock after reset, MX6DL and MX6SL have added 396M pfd
+ * workaround in ROM code, as bus clock need it
+ */
+
+ mask480 = ANATOP_PFD_CLKGATE_MASK(0) |
+ ANATOP_PFD_CLKGATE_MASK(1) |
+ ANATOP_PFD_CLKGATE_MASK(2) |
+ ANATOP_PFD_CLKGATE_MASK(3);
+ mask528 = ANATOP_PFD_CLKGATE_MASK(1) |
+ ANATOP_PFD_CLKGATE_MASK(3);
+
+ reg = readl(&ccm->cbcmr);
+ periph2 = ((reg & MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_MASK)
+ >> MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_OFFSET);
+ periph1 = ((reg & MXC_CCM_CBCMR_PRE_PERIPH_CLK_SEL_MASK)
+ >> MXC_CCM_CBCMR_PRE_PERIPH_CLK_SEL_OFFSET);
+
+ /* Checking if PLL2 PFD0 or PLL2 PFD2 is using for periph clock */
+ if ((periph2 != 0x2) && (periph1 != 0x2))
+ mask528 |= ANATOP_PFD_CLKGATE_MASK(0);
+
+ if ((periph2 != 0x1) && (periph1 != 0x1) &&
+ (periph2 != 0x3) && (periph1 != 0x3))
+ mask528 |= ANATOP_PFD_CLKGATE_MASK(2);
+
+ writel(mask480, &anatop->pfd_480_set);
+ writel(mask528, &anatop->pfd_528_set);
+ writel(mask480, &anatop->pfd_480_clr);
+ writel(mask528, &anatop->pfd_528_clr);
+}
+
+#ifdef CONFIG_IMX_HDMI
+void imx_enable_hdmi_phy(void)
+{
+ struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
+ u8 reg;
+ reg = readb(&hdmi->phy_conf0);
+ reg |= HDMI_PHY_CONF0_PDZ_MASK;
+ writeb(reg, &hdmi->phy_conf0);
+ udelay(3000);
+ reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
+ writeb(reg, &hdmi->phy_conf0);
+ udelay(3000);
+ reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
+ writeb(reg, &hdmi->phy_conf0);
+ writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
+}
+
+void imx_setup_hdmi(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
+ int reg;
+
+ /* Turn on HDMI PHY clock */
+ reg = readl(&mxc_ccm->CCGR2);
+ reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK|
+ MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
+ writel(reg, &mxc_ccm->CCGR2);
+ writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
+ reg = readl(&mxc_ccm->chsccdr);
+ reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK|
+ MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK|
+ MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
+ reg |= (CHSCCDR_PODF_DIVIDE_BY_3
+ << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
+ |(CHSCCDR_IPU_PRE_CLK_540M_PFD
+ << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
+ writel(reg, &mxc_ccm->chsccdr);
+}
+#endif
+
+#ifndef CONFIG_SYS_L2CACHE_OFF
+#define IOMUXC_GPR11_L2CACHE_AS_OCRAM 0x00000002
+void v7_outer_cache_enable(void)
+{
+ struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE;
+ unsigned int val;
+
+#if defined CONFIG_MX6SL
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ val = readl(&iomux->gpr[11]);
+ if (val & IOMUXC_GPR11_L2CACHE_AS_OCRAM) {
+ /* L2 cache configured as OCRAM, reset it */
+ val &= ~IOMUXC_GPR11_L2CACHE_AS_OCRAM;
+ writel(val, &iomux->gpr[11]);
+ }
+#endif
+
+ /* Must disable the L2 before changing the latency parameters */
+ clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
+
+ writel(0x132, &pl310->pl310_tag_latency_ctrl);
+ writel(0x132, &pl310->pl310_data_latency_ctrl);
+
+ val = readl(&pl310->pl310_prefetch_ctrl);
+
+ /* Turn on the L2 I/D prefetch */
+ val |= 0x30000000;
+
+ /*
+ * The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
+ * The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
+ * But according to ARM PL310 errata: 752271
+ * ID: 752271: Double linefill feature can cause data corruption
+ * Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
+ * Workaround: The only workaround to this erratum is to disable the
+ * double linefill feature. This is the default behavior.
+ */
+
+#ifndef CONFIG_MX6Q
+ val |= 0x40800000;
+#endif
+ writel(val, &pl310->pl310_prefetch_ctrl);
+
+ val = readl(&pl310->pl310_power_ctrl);
+ val |= L2X0_DYNAMIC_CLK_GATING_EN;
+ val |= L2X0_STNDBY_MODE_EN;
+ writel(val, &pl310->pl310_power_ctrl);
+
+ setbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
+}
+
+void v7_outer_cache_disable(void)
+{
+ struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE;
+
+ clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);