/*
- * (C) Copyright 2011
- * CompuLab, Ltd. <www.compulab.co.il>
+ * (C) Copyright 2011 CompuLab, Ltd. <www.compulab.co.il>
*
* Authors: Mike Rapoport <mike@compulab.co.il>
* Igor Grinberg <grinberg@compulab.co.il>
#include <netdev.h>
#include <net.h>
#include <i2c.h>
+#include <usb.h>
#include <twl4030.h>
+#include <linux/compiler.h>
#include <asm/io.h>
#include <asm/arch/mem.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-types.h>
+#include <asm/ehci-omap.h>
+#include <asm/gpio.h>
+
+#include "eeprom.h"
DECLARE_GLOBAL_DATA_PTR;
/*
* Routine: board_init
- * Description: Early hardware init.
+ * Description: hardware init.
*/
int board_init(void)
{
return 0;
}
+static u32 cm_t3x_rev;
+
+/*
+ * Routine: get_board_rev
+ * Description: read system revision
+ */
+u32 get_board_rev(void)
+{
+ if (!cm_t3x_rev)
+ cm_t3x_rev = cm_t3x_eeprom_get_board_rev();
+
+ return cm_t3x_rev;
+};
+
/*
* Routine: misc_init_r
* Description: display die ID
*/
int misc_init_r(void)
{
+ u32 board_rev = get_board_rev();
+ u32 rev_major = board_rev / 100;
+ u32 rev_minor = board_rev - (rev_major * 100);
+
+ if ((rev_minor / 10) * 10 == rev_minor)
+ rev_minor = rev_minor / 10;
+
+ printf("PCB: %u.%u\n", rev_major, rev_minor);
dieid_num_r();
return 0;
MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0)); /*HSUSB0_DATA6*/
MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0)); /*HSUSB0_DATA7*/
+ /* USB EHCI */
+ MUX_VAL(CP(ETK_D0_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT0*/
+ MUX_VAL(CP(ETK_D1_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT1*/
+ MUX_VAL(CP(ETK_D2_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT2*/
+ MUX_VAL(CP(ETK_D7_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT3*/
+ MUX_VAL(CP(ETK_D4_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT4*/
+ MUX_VAL(CP(ETK_D5_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT5*/
+ MUX_VAL(CP(ETK_D6_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT6*/
+ MUX_VAL(CP(ETK_D3_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DT7*/
+ MUX_VAL(CP(ETK_D8_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_DIR*/
+ MUX_VAL(CP(ETK_D9_ES2), (IEN | PTD | EN | M3)); /*HSUSB1_NXT*/
+ MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTD | DIS | M3)); /*HSUSB1_CLK*/
+ MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | DIS | M3)); /*HSUSB1_STP*/
+
+ MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | EN | M3)); /*HSUSB2_DT0*/
+ MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | EN | M3)); /*HSUSB2_DT1*/
+ MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M3)); /*HSUSB2_DT2*/
+ MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M3)); /*HSUSB2_DT3*/
+ MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | EN | M3)); /*HSUSB2_DT4*/
+ MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | EN | M3)); /*HSUSB2_DT5*/
+ MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M3)); /*HSUSB2_DT6*/
+ MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | EN | M3)); /*HSUSB2_DT7*/
+ MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | EN | M3)); /*HSUSB2_DIR*/
+ MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | EN | M3)); /*HSUSB2_NXT*/
+ MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTD | DIS | M3)); /*HSUSB2_CLK*/
+ MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTU | DIS | M3)); /*HSUSB2_STP*/
+
+ /* SB_T35_USB_HUB_RESET_GPIO */
+ MUX_VAL(CP(CAM_WEN), (IDIS | PTD | DIS | M4)); /*GPIO_167*/
+
/* I2C1 */
MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)); /*I2C1_SCL*/
MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)); /*I2C1_SDA*/
+ /* I2C2 */
+ MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0)); /*I2C2_SCL*/
+ MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0)); /*I2C2_SDA*/
+ /* I2C3 */
+ MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)); /*I2C3_SCL*/
+ MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)); /*I2C3_SDA*/
/* control and debug */
MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)); /*SYS_32K*/
cm_t3730_set_muxconf();
}
+#ifdef CONFIG_GENERIC_MMC
+int board_mmc_init(bd_t *bis)
+{
+ return omap_mmc_init(0, 0, 0);
+}
+#endif
+
/*
* Routine: setup_net_chip_gmpc
* Description: Setting up the configuration GPMC registers specific to the
{
/* Set GPIO1 of TPS65930 as output */
twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
- TWL4030_BASEADD_GPIO+0x03);
+ TWL4030_BASEADD_GPIO + 0x03);
/* Send a pulse on the GPIO pin */
twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
- TWL4030_BASEADD_GPIO+0x0C);
+ TWL4030_BASEADD_GPIO + 0x0C);
udelay(1);
twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
- TWL4030_BASEADD_GPIO+0x09);
- udelay(1);
+ TWL4030_BASEADD_GPIO + 0x09);
+ mdelay(40);
twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02,
- TWL4030_BASEADD_GPIO+0x0C);
+ TWL4030_BASEADD_GPIO + 0x0C);
+ mdelay(1);
}
#else
static inline void reset_net_chip(void) {}
#endif
+#ifdef CONFIG_SMC911X
/*
* Routine: handle_mac_address
* Description: prepare MAC address for on-board Ethernet.
if (rc)
return 0;
-#ifdef CONFIG_DRIVER_OMAP34XX_I2C
- rc = i2c_read(0x50, 0, 1, enetaddr, 6);
+ rc = cm_t3x_eeprom_read_mac_addr(enetaddr);
if (rc)
return rc;
-#endif
if (!is_valid_ether_addr(enetaddr))
return -1;
{
int rc = 0, rc1 = 0;
-#ifdef CONFIG_SMC911X
setup_net_chip_gmpc();
reset_net_chip();
rc1 = handle_mac_address();
if (rc1)
- printf("CM-T3x: No MAC address found\n");
+ printf("No MAC address found! ");
rc1 = smc911x_initialize(0, CM_T3X_SMC911X_BASE);
if (rc1 > 0)
rc1 = smc911x_initialize(1, SB_T35_SMC911X_BASE);
if (rc1 > 0)
rc++;
-#endif
return rc;
}
+#endif
+
+void __weak get_board_serial(struct tag_serialnr *serialnr)
+{
+ /*
+ * This corresponds to what happens when we can communicate with the
+ * eeprom but don't get a valid board serial value.
+ */
+ serialnr->low = 0;
+ serialnr->high = 0;
+};
+
+#ifdef CONFIG_USB_EHCI_OMAP
+struct omap_usbhs_board_data usbhs_bdata = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+};
+
+#define SB_T35_USB_HUB_RESET_GPIO 167
+int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+ u8 val;
+ int offset;
+
+ if (gpio_request(SB_T35_USB_HUB_RESET_GPIO, "SB-T35 usb hub reset")) {
+ printf("Error: can't obtain GPIO %d for SB-T35 usb hub reset",
+ SB_T35_USB_HUB_RESET_GPIO);
+ return -1;
+ }
+
+ gpio_direction_output(SB_T35_USB_HUB_RESET_GPIO, 0);
+ udelay(10);
+ gpio_set_value(SB_T35_USB_HUB_RESET_GPIO, 1);
+ udelay(1000);
+
+ offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_GPIODATADIR1;
+ twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, &val, offset);
+ /* Set GPIO6 and GPIO7 of TPS65930 as output */
+ val |= 0xC0;
+ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, val, offset);
+ offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_SETGPIODATAOUT1;
+ /* Take both PHYs out of reset */
+ twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0xC0, offset);
+ udelay(1);
+
+ return omap_ehci_hcd_init(&usbhs_bdata, hccr, hcor);
+}
+
+int ehci_hcd_stop(void)
+{
+ return omap_ehci_hcd_stop();
+}
+
+#endif /* CONFIG_USB_EHCI_OMAP */
projects / karo-tx-uboot.git / blobdiff