#include <asm/gpio.h>
#include <asm/arch/iomux-mx53.h>
#include <asm/arch/clock.h>
+#include <asm/arch/hab.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/sys_proto.h>
PAD_CTL_SRE_FAST | PAD_CTL_PUS_47K_UP)
char __uboot_img_end[0] __attribute__((section(".__uboot_img_end")));
+char __csf_data[0] __attribute__((section(".__csf_data")));
static iomux_v3_cfg_t tx53_pads[] = {
/* NAND flash pads are set up in lowlevel_init.S */
{
struct mxc_ccm_reg *ccm_regs = (void *)CCM_BASE_ADDR;
- gpio_request_array(tx53_gpios, ARRAY_SIZE(tx53_gpios));
- imx_iomux_v3_setup_multiple_pads(tx53_pads, ARRAY_SIZE(tx53_pads));
-
writel(0x77777777, AIPS1_BASE_ADDR + 0x00);
writel(0x77777777, AIPS1_BASE_ADDR + 0x04);
writel(0xfff00000, &ccm_regs->CCGR7);
writel(0x00000000, &ccm_regs->cmeor);
+ imx_iomux_v3_setup_multiple_pads(tx53_pads, ARRAY_SIZE(tx53_pads));
+
return 0;
}
{
int ret;
+ ret = gpio_request_array(tx53_gpios, ARRAY_SIZE(tx53_gpios));
+ if (ret < 0) {
+ printf("Failed to request tx53_gpios: %d\n", ret);
+ }
+
/* Address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x1000;
printf("WDOG RESET detected; Skipping PMIC setup\n");
else
printf("<CTRL-C> detected; safeboot enabled\n");
- return 1;
+ return 0;
}
ret = setup_pmic_voltages();
.upper_margin = 2,
.vsync_len = 10,
.lower_margin = 2,
- .sync = FB_SYNC_CLK_LAT_FALL,
},
{
/* Emerging ET0500G0DH6 800 x 480 display.
}
karo_fdt_move_fdt();
- lcd_bl_polarity = karo_fdt_get_backlight_polarity(working_fdt);
if (video_mode == NULL) {
debug("Disabling LCD\n");
lcd_enabled = 0;
return;
}
+
+ lcd_bl_polarity = karo_fdt_get_backlight_polarity(working_fdt);
vm = video_mode;
if (karo_fdt_get_fb_mode(working_fdt, video_mode, &fb_mode) == 0) {
p = &fb_mode;
u8 mac[ETH_ALEN];
imx_get_mac_from_fuse(0, mac);
- if (!is_valid_ether_addr(mac)) {
+ if (!is_valid_ethaddr(mac)) {
printf("No valid MAC address programmed\n");
return;
}
gpio_set_value(TX53_RESET_OUT_GPIO, 1);
clear_ctrlc();
+
+ get_hab_status();
+
return ret;
}
karo_fdt_enable_node(blob, "stk5led", 0);
fdt_fixup_mtdparts(blob, nodes, ARRAY_SIZE(nodes));
- fdt_fixup_ethernet(blob);
karo_fdt_fixup_touchpanel(blob, tx53_touchpanels,
ARRAY_SIZE(tx53_touchpanels));