karo: tx6ul: fix bogus GPIO numbers

[karo-tx-uboot.git] / board / karo / tx6 / tx6ul.c

diff --git a/board/karo/tx6/tx6ul.c b/board/karo/tx6/tx6ul.c
index 2c0a91fd535a54506e3b143e21eee256d54a0044..b216b112598a6078c9918cee984a676c72391f05 100644 (file)
--- a/board/karo/tx6/tx6ul.c
+++ b/board/karo/tx6/tx6ul.c
@@ -693,30 +693,26 @@ static const iomux_v3_cfg_t stk5_pads[] = {
 
        /* TSC200x PEN IRQ */
        MX6_PAD_JTAG_TMS__GPIO1_IO11 | MUX_PAD_CTRL(TX6_GPIO_IN_PAD_CTRL),
-#if 0
+
        /* EDT-FT5x06 Polytouch panel */
-       MX6_PAD_NAND_CS2__GPIO6_IO15 | MUX_PAD_CTRL(TX6_GPIO_IN_PAD_CTRL), /* IRQ */
-       MX6_PAD_EIM_A16__GPIO2_IO22 | MUX_PAD_CTRL(TX6_GPIO_OUT_PAD_CTRL), /* RESET */
-       MX6_PAD_EIM_A17__GPIO2_IO21 | MUX_PAD_CTRL(TX6_GPIO_OUT_PAD_CTRL), /* WAKE */
+       MX6_PAD_SNVS_TAMPER2__GPIO5_IO02 | MUX_PAD_CTRL(TX6_GPIO_IN_PAD_CTRL), /* IRQ */
+       MX6_PAD_SNVS_TAMPER3__GPIO5_IO03 | MUX_PAD_CTRL(TX6_GPIO_OUT_PAD_CTRL), /* RESET */
+       MX6_PAD_SNVS_TAMPER8__GPIO5_IO08 | MUX_PAD_CTRL(TX6_GPIO_OUT_PAD_CTRL), /* WAKE */
 
        /* USBH1 */
-       MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(TX6_GPIO_OUT_PAD_CTRL), /* VBUSEN */
-       MX6_PAD_EIM_D30__GPIO3_IO30 | MUX_PAD_CTRL(TX6_GPIO_IN_PAD_CTRL), /* OC */
+       MX6_PAD_GPIO1_IO02__USB_OTG2_PWR | MUX_PAD_CTRL(TX6_GPIO_OUT_PAD_CTRL), /* VBUSEN */
+       MX6_PAD_GPIO1_IO03__USB_OTG2_OC | MUX_PAD_CTRL(TX6_GPIO_IN_PAD_CTRL), /* OC */
+
        /* USBOTG */
-       MX6_PAD_EIM_D23__GPIO3_IO23 | MUX_PAD_CTRL(TX6_GPIO_IN_PAD_CTRL), /* USBOTG ID */
-       MX6_PAD_GPIO_7__GPIO1_IO07 | MUX_PAD_CTRL(TX6_GPIO_OUT_PAD_CTRL), /* VBUSEN */
-       MX6_PAD_GPIO_8__GPIO1_IO08 | MUX_PAD_CTRL(TX6_GPIO_IN_PAD_CTRL), /* OC */
-#endif
+       MX6_PAD_UART3_CTS_B__GPIO1_IO26 | MUX_PAD_CTRL(TX6_GPIO_OUT_PAD_CTRL), /* VBUSEN */
+       MX6_PAD_UART3_RTS_B__GPIO1_IO27 | MUX_PAD_CTRL(TX6_GPIO_IN_PAD_CTRL), /* OC */
 };
 
 static const struct gpio stk5_gpios[] = {
        { TX6UL_LED_GPIO, GPIOFLAG_OUTPUT_INIT_LOW, "HEARTBEAT LED", },
 
-       { IMX_GPIO_NR(3, 23), GPIOFLAG_INPUT, "USBOTG ID", },
-       { IMX_GPIO_NR(1, 8), GPIOFLAG_INPUT, "USBOTG OC", },
-       { IMX_GPIO_NR(1, 7), GPIOFLAG_OUTPUT_INIT_LOW, "USBOTG VBUS enable", },
-       { IMX_GPIO_NR(3, 30), GPIOFLAG_INPUT, "USBH1 OC", },
-       { IMX_GPIO_NR(3, 31), GPIOFLAG_OUTPUT_INIT_LOW, "USBH1 VBUS enable", },
+       { IMX_GPIO_NR(1, 27), GPIOFLAG_INPUT, "USBOTG OC", },
+       { IMX_GPIO_NR(1, 26), GPIOFLAG_OUTPUT_INIT_LOW, "USBOTG VBUS enable", },
 };
 
 #ifdef CONFIG_LCD