#include <common.h>
#include <lcd.h>
-#include <asm/io.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mmc.h>
-#include <asm/arch/power.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/mipi_dsim.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/power.h>
+#include <asm/arch/mipi_dsim.h>
#include <power/pmic.h>
#include <power/max77686_pmic.h>
#include <power/battery.h>
#include <usb.h>
#include <usb/s3c_udc.h>
#include <usb_mass_storage.h>
-#include <samsung/misc.h>
DECLARE_GLOBAL_DATA_PTR;
board_rev = modelrev << 8;
}
-#ifdef CONFIG_DISPLAY_BOARDINFO
-int checkboard(void)
-{
- puts("Board:\tTRATS2\n");
- printf("HW Revision:\t0x%04x\n", board_rev);
-
- return 0;
-}
-#endif
-
u32 get_board_rev(void)
{
return board_rev;
}
#endif
-int board_early_init_f(void)
+int exynos_early_init_f(void)
{
- check_hw_revision();
board_external_gpio_init();
- gd->flags |= GD_FLG_DISABLE_CONSOLE;
-
return 0;
}
static int pmic_init_max77686(void);
-int board_init(void)
+int exynos_init(void)
{
- struct exynos4_power *pwr =
- (struct exynos4_power *)samsung_get_base_power();
-
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
- /* workaround: clear INFORM4..5 */
- writel(0, (unsigned int)&pwr->inform4);
- writel(0, (unsigned int)&pwr->inform5);
+ check_hw_revision();
+ printf("HW Revision:\t0x%04x\n", board_rev);
return 0;
}
-int power_init_board(void)
+int exynos_power_init(void)
{
int chrg;
struct power_battery *pb;
return 0;
}
-int dram_init(void)
-{
- u32 size_mb;
-
- size_mb = (get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) +
- get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE) +
- get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE) +
- get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE)) >> 20;
-
- gd->ram_size = size_mb << 20;
-
- return 0;
-}
-
-void dram_init_banksize(void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
- gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
- gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
- gd->bd->bi_dram[2].start = PHYS_SDRAM_3;
- gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE;
- gd->bd->bi_dram[3].start = PHYS_SDRAM_4;
- gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE;
-}
-
-int board_mmc_init(bd_t *bis)
-{
- int err0, err2 = 0;
-
- gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2();
-
- /* eMMC_EN: SD_0_CDn: GPK0[2] Output High */
- s5p_gpio_direction_output(&gpio2->k0, 2, 1);
- s5p_gpio_set_pull(&gpio2->k0, 2, GPIO_PULL_NONE);
-
- /*
- * eMMC GPIO:
- * SDR 8-bit@48MHz at MMC0
- * GPK0[0] SD_0_CLK(2)
- * GPK0[1] SD_0_CMD(2)
- * GPK0[2] SD_0_CDn -> Not used
- * GPK0[3:6] SD_0_DATA[0:3](2)
- * GPK1[3:6] SD_0_DATA[0:3](3)
- *
- * DDR 4-bit@26MHz at MMC4
- * GPK0[0] SD_4_CLK(3)
- * GPK0[1] SD_4_CMD(3)
- * GPK0[2] SD_4_CDn -> Not used
- * GPK0[3:6] SD_4_DATA[0:3](3)
- * GPK1[3:6] SD_4_DATA[4:7](4)
- */
-
- err0 = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE);
-
- /*
- * MMC device init
- * mmc0 : eMMC (8-bit buswidth)
- * mmc2 : SD card (4-bit buswidth)
- */
- if (err0)
- debug("SDMMC0 not configured\n");
- else
- err0 = s5p_mmc_init(0, 8);
-
- /* T-flash detect */
- s5p_gpio_cfg_pin(&gpio2->x3, 4, 0xf);
- s5p_gpio_set_pull(&gpio2->x3, 4, GPIO_PULL_UP);
-
- /*
- * Check the T-flash detect pin
- * GPX3[4] T-flash detect pin
- */
- if (!s5p_gpio_get_value(&gpio2->x3, 4)) {
- err2 = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
- if (err2)
- debug("SDMMC2 not configured\n");
- else
- err2 = s5p_mmc_init(2, 4);
- }
-
- return err0 & err2;
-}
-
#ifdef CONFIG_USB_GADGET
static int s5pc210_phy_control(int on)
{
*/
#ifdef CONFIG_LCD
-static struct mipi_dsim_config dsim_config = {
- .e_interface = DSIM_VIDEO,
- .e_virtual_ch = DSIM_VIRTUAL_CH_0,
- .e_pixel_format = DSIM_24BPP_888,
- .e_burst_mode = DSIM_BURST_SYNC_EVENT,
- .e_no_data_lane = DSIM_DATA_LANE_4,
- .e_byte_clk = DSIM_PLL_OUT_DIV8,
- .hfp = 1,
-
- .p = 3,
- .m = 120,
- .s = 1,
-
- /* D-PHY PLL stable time spec :min = 200usec ~ max 400usec */
- .pll_stable_time = 500,
-
- /* escape clk : 10MHz */
- .esc_clk = 20 * 1000000,
-
- /* stop state holding counter after bta change count 0 ~ 0xfff */
- .stop_holding_cnt = 0x7ff,
- /* bta timeout 0 ~ 0xff */
- .bta_timeout = 0xff,
- /* lp rx timeout 0 ~ 0xffff */
- .rx_timeout = 0xffff,
-};
-
-static struct exynos_platform_mipi_dsim dsim_platform_data = {
- .lcd_panel_info = NULL,
- .dsim_config = &dsim_config,
-};
-
-static struct mipi_dsim_lcd_device mipi_lcd_device = {
- .name = "s6e8ax0",
- .id = -1,
- .bus_id = 0,
- .platform_data = (void *)&dsim_platform_data,
-};
-
-static int mipi_power(void)
+int mipi_power(void)
{
struct pmic *p = pmic_get("MAX77686_PMIC");
s5p_gpio_set_value(&gpio1->f2, 1, 1);
}
-vidinfo_t panel_info = {
- .vl_freq = 60,
- .vl_col = 720,
- .vl_row = 1280,
- .vl_width = 720,
- .vl_height = 1280,
- .vl_clkp = CONFIG_SYS_HIGH,
- .vl_hsp = CONFIG_SYS_LOW,
- .vl_vsp = CONFIG_SYS_LOW,
- .vl_dp = CONFIG_SYS_LOW,
- .vl_bpix = 4, /* Bits per pixel, 2^4 = 16 */
-
- /* s6e8ax0 Panel infomation */
- .vl_hspw = 5,
- .vl_hbpd = 10,
- .vl_hfpd = 10,
-
- .vl_vspw = 2,
- .vl_vbpd = 1,
- .vl_vfpd = 13,
- .vl_cmd_allow_len = 0xf,
- .mipi_enabled = 1,
-
- .dual_lcd_enabled = 0,
-
- .init_delay = 0,
- .power_on_delay = 25,
- .reset_delay = 0,
- .interface_mode = FIMD_RGB_INTERFACE,
-};
-
-void init_panel_info(vidinfo_t *vid)
+void exynos_lcd_misc_init(vidinfo_t *vid)
{
- vid->logo_on = 1;
- vid->resolution = HD_RESOLUTION;
- vid->rgb_mode = MODE_RGB_P;
-
- vid->power_on_delay = 30;
-
- mipi_lcd_device.reverse_panel = 1;
-
#ifdef CONFIG_TIZEN
get_tizen_logo_info(vid);
#endif
-
- strcpy(dsim_platform_data.lcd_panel_name, mipi_lcd_device.name);
- dsim_platform_data.mipi_power = mipi_power;
- dsim_platform_data.phy_enable = set_mipi_phy_ctrl;
- dsim_platform_data.lcd_panel_info = (void *)vid;
- exynos_mipi_dsi_register_lcd_device(&mipi_lcd_device);
-
+#ifdef CONFIG_S6E8AX0
s6e8ax0_init();
-
- exynos_set_dsim_platform_data(&dsim_platform_data);
-}
-#endif /* LCD */
-
-#ifdef CONFIG_MISC_INIT_R
-int misc_init_r(void)
-{
-#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- set_board_info();
-#endif
-#ifdef CONFIG_LCD_MENU
- keys_init();
- check_boot_mode();
#endif
-#ifdef CONFIG_CMD_BMP
- if (panel_info.logo_on)
- draw_logo();
-#endif
- return 0;
}
-#endif
+#endif /* LCD */
projects / karo-tx-uboot.git / blobdiff