powerpc/t1040qds: Add Video - HDMI support

[karo-tx-uboot.git] / include / configs / T1040QDS.h

diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h
index cfaac43050326040e4f9fe9b22787efa5a1b9abc..e776a467a089272a1f61b57d3e8e98e4dd5c793b 100644 (file)
--- a/include/configs/T1040QDS.h
+++ b/include/configs/T1040QDS.h
@@ -32,8 +32,8 @@
 #ifdef CONFIG_RAMBOOT_PBL
 #define CONFIG_RAMBOOT_TEXT_BASE       CONFIG_SYS_TEXT_BASE
 #define CONFIG_RESET_VECTOR_ADDRESS    0xfffffffc
-#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t1040qds/t1040_pbi.cfg
-#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t1040qds/t1040_rcw.cfg
+#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t1040qds/t1040_pbi.cfg
+#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t1040qds/t1040_rcw.cfg
 #endif
 
 /* High Level Configuration Options */
@@ -41,11 +41,10 @@
 #define CONFIG_E500                    /* BOOKE e500 family */
 #define CONFIG_E500MC                  /* BOOKE e500mc family */
 #define CONFIG_SYS_BOOK3E_HV           /* Category E.HV supported */
-#define CONFIG_MPC85xx                 /* MPC85xx/PQ3 platform */
 #define CONFIG_MP                      /* support multiple processors */
 
 #ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE   0xeff80000
+#define CONFIG_SYS_TEXT_BASE   0xeff40000
 #endif
 
 #ifndef CONFIG_RESET_VECTOR_ADDRESS
@@ -93,12 +92,12 @@
 #define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV          0
 #define CONFIG_ENV_SIZE                        0x2000
-#define CONFIG_ENV_OFFSET              (512 * 1105)
+#define CONFIG_ENV_OFFSET              (512 * 1658)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_SIZE                        CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET              (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_OFFSET              (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
 #define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
@@ -376,7 +375,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN         (512 * 1024)
-#define CONFIG_SYS_MALLOC_LEN          (4 * 1024 * 1024)
+#define CONFIG_SYS_MALLOC_LEN          (10 * 1024 * 1024)
 
 /* Serial Port - controlled on board with jumper J8
  * open - index 2
@@ -402,6 +401,25 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 
+/* Video */
+#define CONFIG_FSL_DIU_FB
+#ifdef CONFIG_FSL_DIU_FB
+#define CONFIG_SYS_DIU_ADDR    (CONFIG_SYS_CCSRBAR + 0x180000)
+#define CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+/*
+ * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
+ * disable empty flash sector detection, which is I/O-intensive.
+ */
+#undef CONFIG_SYS_FLASH_EMPTY_INFO
+#endif
+
 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT
 #define CONFIG_OF_BOARD_SETUP
@@ -427,6 +445,11 @@ unsigned long get_board_ddr_clk(void);
 
 /* I2C bus multiplexer */
 #define I2C_MUX_CH_DEFAULT      0x8
+#define I2C_MUX_CH_DIU         0xC
+
+/* LDI/DVI Encoder for display */
+#define CONFIG_SYS_I2C_LDI_ADDR         0x38
+#define CONFIG_SYS_I2C_DVI_ADDR         0x75
 
 /*
  * RTC configuration
@@ -583,17 +606,17 @@ unsigned long get_board_ddr_clk(void);
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 545KB (1089 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
+ * about 825KB (1650 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR     (512 * 1130)
+#define CONFIG_SYS_QE_FMAN_FW_ADDR     (512 * 1680)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR     (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_QE_FMAN_FW_ADDR     (8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR             0xEFF40000
+#define CONFIG_SYS_QE_FMAN_FW_ADDR             0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH   0x10000
 #define CONFIG_SYS_FDT_PAD             (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
@@ -612,9 +635,8 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 #ifdef CONFIG_FMAN_ENET
-#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x10
-#define CONFIG_SYS_FM1_DTSEC6_PHY_ADDR 0x11
-#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 4
+#define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x01
+#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x02
 
 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR    0x1c
 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR    0x1d
@@ -671,7 +693,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 #define CONFIG_SYS_MAXARGS     16              /* max number of command args */
 #define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ          1000            /* decrementer freq: 1ms ticks*/
 
 /*
  * For booting Linux, the board info and command line data
@@ -706,6 +727,7 @@ unsigned long get_board_ddr_clk(void);
        "bank_intlv=cs0_cs1;"                                   \
        "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
        "netdev=eth0\0"                                         \
+       "video-mode=fslfb:1024x768-32@60,monitor=dvi\0"         \
        "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
        "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
        "tftpflash=tftpboot $loadaddr $uboot && "               \