#ifndef __MX28EVK_CONFIG_H__
#define __MX28EVK_CONFIG_H__
-/*
- * SoC configurations
- */
+/* SoC configurations */
#define CONFIG_MX28 /* i.MX28 SoC */
#define CONFIG_MXS_GPIO /* GPIO control */
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_ARCH_MISC_INIT
-/*
- * SPL
- */
+/* SPL */
#define CONFIG_SPL
#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs"
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
-/*
- * U-Boot Commands
- */
+/* U-Boot Commands */
#include <config_cmd_default.h>
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_SPI
#define CONFIG_CMD_USB
#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
-/*
- * Memory configurations
- */
+/* Memory configurations */
#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
#define PHYS_SDRAM_1 0x40000000 /* Base address */
#define PHYS_SDRAM_1_SIZE 0x40000000 /* Max 1 GB RAM */
#define CONFIG_SYS_TEXT_BASE 0x40000100
#define CONFIG_ENV_OVERWRITE
-/*
- * U-Boot general configurations
- */
+/* U-Boot general configurations */
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_PROMPT "MX28EVK U-Boot > "
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */
#define CONFIG_CMDLINE_EDITING /* Command history etc */
#define CONFIG_SYS_HUSH_PARSER
-/*
- * Serial Driver
- */
+/* Serial Driver */
#define CONFIG_PL011_SERIAL
#define CONFIG_PL011_CLOCK 24000000
#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE }
#define CONFIG_CONS_INDEX 0
#define CONFIG_BAUDRATE 115200 /* Default baud rate */
-/*
- * DMA
- */
+/* DMA */
#define CONFIG_APBH_DMA
-/*
- * MMC Driver
- */
-#define CONFIG_ENV_IS_IN_MMC
+/* MMC Driver */
#ifdef CONFIG_ENV_IS_IN_MMC
#define CONFIG_ENV_OFFSET (256 * 1024)
#define CONFIG_ENV_SIZE (16 * 1024)
#define CONFIG_MXS_MMC
#endif
-/*
- * NAND Driver
- */
+/* NAND Driver */
+#define CONFIG_ENV_SIZE (16 * 1024)
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_MXS
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x60000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+
+/* Environment is in NAND */
+#ifdef CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+#define CONFIG_ENV_SECT_SIZE (128 * 1024)
+#define CONFIG_ENV_RANGE (512 * 1024)
+#define CONFIG_ENV_OFFSET 0x300000
+#define CONFIG_ENV_OFFSET_REDUND \
+ (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
#endif
-/*
- * Ethernet on SOC (FEC)
- */
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define MTDIDS_DEFAULT "nand0=gpmi-nand"
+#define MTDPARTS_DEFAULT \
+ "mtdparts=gpmi-nand:" \
+ "3m(bootloader)ro," \
+ "512k(environment)," \
+ "512k(redundant-environment)," \
+ "4m(kernel)," \
+ "128k(fdt)," \
+ "8m(ramdisk)," \
+ "-(filesystem)"
+#endif
+
+/* Ethernet on SOC (FEC) */
#ifdef CONFIG_CMD_NET
#define CONFIG_NET_MULTI
#define CONFIG_ETHPRIME "FEC0"
#define CONFIG_FEC_MXC
-#define CONFIG_FEC_MXC_MULTI
#define CONFIG_MII
#define CONFIG_FEC_XCV_TYPE RMII
#define CONFIG_MX28_FEC_MAC_IN_OCOTP
#endif
-/*
- * RTC
- */
+/* RTC */
#ifdef CONFIG_CMD_DATE
#define CONFIG_RTC_MXS
#endif
-/*
- * USB
- */
+/* USB */
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MXS
-#define CONFIG_EHCI_MXS_PORT 1
+#define CONFIG_EHCI_MXS_PORT1
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#define CONFIG_EHCI_IS_TDI
#define CONFIG_USB_STORAGE
#define CONFIG_USB_HOST_ETHER
#define CONFIG_SYS_I2C_SPEED 400000
#endif
-/*
- * SPI
- */
+/* SPI */
#ifdef CONFIG_CMD_SPI
#define CONFIG_HARD_SPI
#define CONFIG_MXS_SPI
-#define CONFIG_MXS_SPI_DMA_ENABLE
#define CONFIG_SPI_HALF_DUPLEX
#define CONFIG_DEFAULT_SPI_BUS 2
#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0
#endif
#endif
-/*
- * Boot Linux
- */
+/* Boot Linux */
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 1
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_LOADADDR 0x42000000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_OF_LIBFDT
-/*
- * Extra Environments
- */
+/* Extra Environments */
#define CONFIG_EXTRA_ENV_SETTINGS \
"update_nand_full_filename=u-boot.nand\0" \
"update_nand_firmware_filename=u-boot.sb\0" \
"uimage=uImage\0" \
"console_fsl=ttyAM0\0" \
"console_mainline=ttyAMA0\0" \
+ "fdt_file=imx28-evk.dtb\0" \
+ "fdt_addr=0x41000000\0" \
+ "boot_fdt=try\0" \
+ "ip_dyn=yes\0" \
"mmcdev=0\0" \
"mmcpart=2\0" \
- "mmcroot=/dev/mmcblk0p3 rw\0" \
- "mmcrootfstype=ext3 rootwait\0" \
+ "mmcroot=/dev/mmcblk0p3 rw rootwait\0" \
"mmcargs=setenv bootargs console=${console_mainline},${baudrate} " \
- "root=${mmcroot} " \
- "rootfstype=${mmcrootfstype}\0" \
+ "root=${mmcroot}\0" \
"loadbootscript=" \
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
"loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "bootm\0" \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "bootm ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootm; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootm; " \
+ "fi;\0" \
"netargs=setenv bootargs console=${console_mainline},${baudrate} " \
"root=/dev/nfs " \
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"netboot=echo Booting from net ...; " \
"run netargs; " \
- "dhcp ${uimage}; bootm\0"
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${uimage}; " \
+ "if test ${boot_fdt} = yes; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "bootm ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootm; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi;" \
+ "fi; " \
+ "else " \
+ "bootm; " \
+ "fi;\0"
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
projects / karo-tx-uboot.git / blobdiff