sama5d3xek: enable PMECC header generation

[karo-tx-uboot.git] / include / configs / sama5d3xek.h

diff --git a/include/configs/sama5d3xek.h b/include/configs/sama5d3xek.h
index 76fa500eddb5b137fe407ae6ce71514015def7a7..fe63d80ed5e35287db4aadeb8a2959aae333176d 100644 (file)
--- a/include/configs/sama5d3xek.h
+++ b/include/configs/sama5d3xek.h
@@ -20,18 +20,22 @@
 /* ARM asynchronous clock */
 #define CONFIG_SYS_AT91_SLOW_CLOCK      32768
 #define CONFIG_SYS_AT91_MAIN_CLOCK      12000000 /* from 12 MHz crystal */
-#define CONFIG_SYS_HZ                  1000
 
 #define CONFIG_AT91FAMILY
 #define CONFIG_ARCH_CPU_INIT
 
+#ifndef CONFIG_SPL_BUILD
 #define CONFIG_SKIP_LOWLEVEL_INIT
+#endif
+
 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_DISPLAY_CPUINFO
 
 #define CONFIG_CMD_BOOTZ
 #define CONFIG_OF_LIBFDT               /* Device Tree support */
 
+#define CONFIG_SYS_GENERIC_BOARD
+
 /* general purpose I/O */
 #define CONFIG_AT91_GPIO
 
@@ -94,8 +98,12 @@
 #define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
 #define CONFIG_SYS_SDRAM_SIZE          0x20000000
 
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_INIT_SP_ADDR                0x310000
+#else
 #define CONFIG_SYS_INIT_SP_ADDR \
        (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+#endif
 
 /* SerialFlash */
 #define CONFIG_CMD_SF
@@ -153,6 +161,7 @@
 
 #ifdef CONFIG_CMD_USB
 #define CONFIG_USB_ATMEL
+#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
 #define CONFIG_USB_OHCI_NEW
 #define CONFIG_SYS_USB_OHCI_CPU_INIT
 #define CONFIG_SYS_USB_OHCI_REGS_BASE          ATMEL_BASE_OHCI
@@ -162,6 +171,14 @@
 #define CONFIG_USB_STORAGE
 #endif
 
+/* USB device */
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_ATMEL_USBA
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETH_RNDIS
+#define CONFIG_USBNET_MANUFACTURER      "Atmel SAMA5D3xEK"
+
 #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
 #define CONFIG_CMD_FAT
 #endif
@@ -227,4 +244,55 @@
 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN          (1024 * 1024)
 
+/* SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE           0x300000
+#define CONFIG_SPL_MAX_SIZE            0x10000
+#define CONFIG_SPL_BSS_START_ADDR      0x20000000
+#define CONFIG_SPL_BSS_MAX_SIZE                0x80000
+#define CONFIG_SYS_SPL_MALLOC_START    0x20080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE     0x80000
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SYS_MONITOR_LEN         (512 << 10)
+
+#ifdef CONFIG_SYS_USE_MMC
+#define CONFIG_SPL_LDSCRIPT            arch/arm/cpu/at91-common/u-boot-spl.lds
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS     0x400
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION   1
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME       "u-boot.img"
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+
+#elif CONFIG_SYS_USE_NANDFLASH
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS    0x40000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_SIZE      0x800
+#define CONFIG_SYS_NAND_PAGE_COUNT     64
+#define CONFIG_SYS_NAND_OOBSIZE                64
+#define CONFIG_SYS_NAND_BLOCK_SIZE     0x20000
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS  0x0
+#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
+
+#elif CONFIG_SYS_USE_SERIALFLASH
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SPL_SPI_BUS             0
+#define CONFIG_SPL_SPI_CS              0
+#define CONFIG_SYS_SPI_U_BOOT_OFFS     0x8400
+
+#endif
+
 #endif