depends on !SPL_BUILD
help
The old configuration infrastructure (= mkconfig + boards.cfg)
- provided the extra options field. It you have something like
+ provided the extra options field. If you have something like
"HAS_BAR,BAZ=64", the optional options
#define CONFIG_HAS
#define CONFIG_BAZ 64
endmenu # Boot images
source "arch/Kconfig"
+
+source "common/Kconfig"
+
+source "dts/Kconfig"
+
+source "net/Kconfig"
+
+source "drivers/Kconfig"
+
+source "fs/Kconfig"
+
+source "lib/Kconfig"
F: arch/arm/include/asm/arch-omap*/
F: arch/arm/include/asm/ti-common/
+ARM UNIPHIER
+M: Masahiro Yamada <yamada.m@jp.panasonic.com>
+S: Maintained
+T: git git://git.denx.de/u-boot-uniphier.git
+F: arch/arm/cpu/armv7/uniphier/
+F: arch/arm/include/asm/arch-uniphier/
+F: configs/ph1_*_defconfig
+F: drivers/serial/serial_uniphier.c
+
ARM ZYNQ
M: Michal Simek <monstr@monstr.eu>
S: Maintained
libs-y += net/
libs-y += disk/
libs-y += drivers/
-libs-$(CONFIG_DM) += drivers/core/
libs-y += drivers/dma/
libs-y += drivers/gpio/
libs-y += drivers/i2c/
-libs-y += drivers/input/
libs-y += drivers/mmc/
libs-y += drivers/mtd/
libs-$(CONFIG_CMD_NAND) += drivers/mtd/nand/
libs-$(CONFIG_HAS_POST) += post/
libs-y += test/
libs-y += test/dm/
-libs-$(CONFIG_DM_DEMO) += drivers/demo/
ifneq (,$(filter $(SOC), mx25 mx27 mx5 mx6 mx31 mx35 mxs vf610))
libs-y += arch/$(ARCH)/imx-common/
specific to be undertaken on a native platform. The sandbox is also used to
run some of U-Boot's tests.
-See board/sandbox/sandbox/README.sandbox for more details.
+See board/sandbox/README.sandbox for more details.
Configuration Options:
interleaving mode, handled by Dickens for Freescale layerscape
SoCs with ARM core.
+ CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
+ Number of controllers used as main memory.
+
+ CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
+ Number of controllers used for other than main memory.
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
downloads. This buffer should be as large as possible for a
platform. Define this to the size available RAM for fastboot.
+ CONFIG_FASTBOOT_FLASH
+ The fastboot protocol includes a "flash" command for writing
+ the downloaded image to a non-volatile storage device. Define
+ this to enable the "fastboot flash" command.
+
+ CONFIG_FASTBOOT_FLASH_MMC_DEV
+ The fastboot "flash" command requires additional information
+ regarding the non-volatile storage device. Define this to
+ the eMMC device that fastboot should use to store the image.
+
- Journaling Flash filesystem support:
CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
CONFIG_JFFS2_NAND_DEV
The memory will be freed (or in fact just forgotton) when
U-Boot relocates itself.
- Pre-relocation malloc() is only supported on sandbox
+ Pre-relocation malloc() is only supported on ARM and sandbox
at present but is fairly easy to enable for other archs.
- Pre-relocation malloc() is only supported on ARM at present
- but is fairly easy to enable for other archs.
-
- CONFIG_SYS_BOOTM_LEN:
Normally compressed uImages are limited to an
uncompressed size of 8 MBytes. If this is not enough,
config ARM
bool "ARM architecture"
+ select SUPPORT_OF_CONTROL
config AVR32
bool "AVR32 architecture"
config MICROBLAZE
bool "MicroBlaze architecture"
+ select SUPPORT_OF_CONTROL
config MIPS
bool "MIPS architecture"
config SANDBOX
bool "Sandbox"
+ select SUPPORT_OF_CONTROL
config SH
bool "SuperH architecture"
config X86
bool "x86 architecture"
+ select SUPPORT_OF_CONTROL
endchoice
config SYS_ARCH
default "arm"
+config ARM64
+ bool
+
choice
prompt "Target select"
config RMOBILE
bool "Renesas ARM SoCs"
+config TARGET_CM_FX6
+ bool "Support cm_fx6"
+
config TARGET_S5P_GONI
bool "Support s5p_goni"
config TEGRA
bool "NVIDIA Tegra"
select SPL
+ select OF_CONTROL if !SPL_BUILD
config TARGET_VEXPRESS_AEMV8A
bool "Support vexpress_aemv8a"
-
-config TARGET_VEXPRESS_AEMV8A_SEMI
- bool "Support vexpress_aemv8a_semi"
+ select ARM64
config TARGET_LS2085A_EMU
bool "Support ls2085a_emu"
+ select ARM64
config TARGET_LS2085A_SIMU
bool "Support ls2085a_simu"
+ select ARM64
config TARGET_LS1021AQDS
bool "Support ls1021aqds_nor"
config TARGET_JORNADA
bool "Support jornada"
+config ARCH_UNIPHIER
+ bool "Panasonic UniPhier platform"
+
endchoice
+source "arch/arm/cpu/armv8/Kconfig"
+
source "arch/arm/cpu/arm926ejs/davinci/Kconfig"
source "arch/arm/cpu/armv7/exynos/Kconfig"
source "arch/arm/cpu/armv7/tegra-common/Kconfig"
+source "arch/arm/cpu/armv7/uniphier/Kconfig"
+
source "arch/arm/cpu/arm926ejs/versatile/Kconfig"
source "arch/arm/cpu/armv7/zynq/Kconfig"
source "board/cm4008/Kconfig"
source "board/cm41xx/Kconfig"
source "board/compulab/cm_t335/Kconfig"
+source "board/compulab/cm_fx6/Kconfig"
source "board/congatec/cgtqmx6eval/Kconfig"
source "board/creative/xfi3/Kconfig"
source "board/davedenx/qong/Kconfig"
pllctl_reg_write(data->pll, ctl, tmp);
mult = data->pll_freq / fpll;
- for (mult = MAX(mult, 1); mult <= MAX_MULT; mult++) {
+ for (mult = max(mult, 1); mult <= MAX_MULT; mult++) {
div = (fpll * mult) / data->pll_freq;
if (div < 1 || div > MAX_DIV)
continue;
void at91_periph_clk_enable(int id)
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ u32 regval;
- if (id > 31)
- writel(1 << (id - 32), &pmc->pcer1);
- else
- writel(1 << id, &pmc->pcer);
+ if (id > AT91_PMC_PCR_PID_MASK)
+ return;
+
+ regval = AT91_PMC_PCR_EN | AT91_PMC_PCR_CMD_WRITE | id;
+
+ writel(regval, &pmc->pcr);
+}
+
+void at91_periph_clk_disable(int id)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ u32 regval;
+
+ if (id > AT91_PMC_PCR_PID_MASK)
+ return;
+
+ regval = AT91_PMC_PCR_CMD_WRITE | id;
+
+ writel(regval, &pmc->pcr);
}
config TARGET_ARNDALE
bool "Exynos5250 Arndale board"
+ select OF_CONTROL if !SPL_BUILD
config TARGET_SMDK5250
bool "SMDK5250 board"
+ select OF_CONTROL if !SPL_BUILD
config TARGET_SNOW
bool "Snow board"
+ select OF_CONTROL if !SPL_BUILD
config TARGET_SMDK5420
bool "SMDK5420 board"
+ select OF_CONTROL if !SPL_BUILD
config TARGET_PEACH_PIT
bool "Peach Pi board"
+ select OF_CONTROL if !SPL_BUILD
endchoice
#include <asm/io.h>
#include <common.h>
#include <asm/arch/ddr3.h>
+#include <asm/arch/psc_defs.h>
void ddr3_init_ddrphy(u32 base, struct ddr3_phy_config *phy_cfg)
{
tmp &= ~KS2_DDR3_PLLCTRL_PHY_RESET;
__raw_writel(tmp, KS2_DDR3APLLCTL1);
}
+
+#ifdef CONFIG_SOC_K2HK
+/**
+ * ddr3_reset_workaround - reset workaround in case if leveling error
+ * detected for PG 1.0 and 1.1 k2hk SoCs
+ */
+void ddr3_err_reset_workaround(void)
+{
+ unsigned int tmp;
+ unsigned int tmp_a;
+ unsigned int tmp_b;
+
+ /*
+ * Check for PGSR0 error bits of DDR3 PHY.
+ * Check for WLERR, QSGERR, WLAERR,
+ * RDERR, WDERR, REERR, WEERR error to see if they are set or not
+ */
+ tmp_a = __raw_readl(KS2_DDR3A_DDRPHYC + KS2_DDRPHY_PGSR0_OFFSET);
+ tmp_b = __raw_readl(KS2_DDR3B_DDRPHYC + KS2_DDRPHY_PGSR0_OFFSET);
+
+ if (((tmp_a & 0x0FE00000) != 0) || ((tmp_b & 0x0FE00000) != 0)) {
+ printf("DDR Leveling Error Detected!\n");
+ printf("DDR3A PGSR0 = 0x%x\n", tmp_a);
+ printf("DDR3B PGSR0 = 0x%x\n", tmp_b);
+
+ /*
+ * Write Keys to KICK registers to enable writes to registers
+ * in boot config space
+ */
+ __raw_writel(KS2_KICK0_MAGIC, KS2_KICK0);
+ __raw_writel(KS2_KICK1_MAGIC, KS2_KICK1);
+
+ /*
+ * Move DDR3A Module out of reset isolation by setting
+ * MDCTL23[12] = 0
+ */
+ tmp_a = __raw_readl(KS2_PSC_BASE +
+ PSC_REG_MDCTL(KS2_LPSC_EMIF4F_DDR3A));
+
+ tmp_a = PSC_REG_MDCTL_SET_RESET_ISO(tmp_a, 0);
+ __raw_writel(tmp_a, KS2_PSC_BASE +
+ PSC_REG_MDCTL(KS2_LPSC_EMIF4F_DDR3A));
+
+ /*
+ * Move DDR3B Module out of reset isolation by setting
+ * MDCTL24[12] = 0
+ */
+ tmp_b = __raw_readl(KS2_PSC_BASE +
+ PSC_REG_MDCTL(KS2_LPSC_EMIF4F_DDR3B));
+ tmp_b = PSC_REG_MDCTL_SET_RESET_ISO(tmp_b, 0);
+ __raw_writel(tmp_b, KS2_PSC_BASE +
+ PSC_REG_MDCTL(KS2_LPSC_EMIF4F_DDR3B));
+
+ /*
+ * Write 0x5A69 Key to RSTCTRL[15:0] to unlock writes
+ * to RSTCTRL and RSTCFG
+ */
+ tmp = __raw_readl(KS2_RSTCTRL);
+ tmp &= KS2_RSTCTRL_MASK;
+ tmp |= KS2_RSTCTRL_KEY;
+ __raw_writel(tmp, KS2_RSTCTRL);
+
+ /*
+ * Set PLL Controller to drive hard reset on SW trigger by
+ * setting RSTCFG[13] = 0
+ */
+ tmp = __raw_readl(KS2_RSTCTRL_RSCFG);
+ tmp &= ~KS2_RSTYPE_PLL_SOFT;
+ __raw_writel(tmp, KS2_RSTCTRL_RSCFG);
+
+ reset_cpu(0);
+ }
+}
+#endif
}
#endif
+#ifdef CONFIG_NAND_MXS
+void setup_gpmi_io_clk(u32 cfg)
+{
+ /* Disable clocks per ERR007177 from MX6 errata */
+ clrbits_le32(&imx_ccm->CCGR4,
+ MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+
+ clrbits_le32(&imx_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+
+ clrsetbits_le32(&imx_ccm->cs2cdr,
+ MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
+ MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
+ MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
+ cfg);
+
+ setbits_le32(&imx_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+ setbits_le32(&imx_ccm->CCGR4,
+ MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+}
+#endif
+
void enable_usboh3_clk(unsigned char enable)
{
u32 reg;
}
+#if defined(CONFIG_FEC_MXC) && !defined(CONFIG_MX6SX)
+void enable_enet_clk(unsigned char enable)
+{
+ u32 mask = MXC_CCM_CCGR1_ENET_CLK_ENABLE_MASK;
+
+ if (enable)
+ setbits_le32(&imx_ccm->CCGR1, mask);
+ else
+ clrbits_le32(&imx_ccm->CCGR1, mask);
+}
+#endif
+
+#ifdef CONFIG_MXC_UART
+void enable_uart_clk(unsigned char enable)
+{
+ u32 mask = MXC_CCM_CCGR5_UART_MASK | MXC_CCM_CCGR5_UART_SERIAL_MASK;
+
+ if (enable)
+ setbits_le32(&imx_ccm->CCGR5, mask);
+ else
+ clrbits_le32(&imx_ccm->CCGR5, mask);
+}
+#endif
+
+#ifdef CONFIG_SPI
+/* spi_num can be from 0 - 4 */
+int enable_cspi_clock(unsigned char enable, unsigned spi_num)
+{
+ u32 mask;
+
+ if (spi_num > 4)
+ return -EINVAL;
+
+ mask = MXC_CCM_CCGR_CG_MASK << (spi_num * 2);
+ if (enable)
+ setbits_le32(&imx_ccm->CCGR1, mask);
+ else
+ clrbits_le32(&imx_ccm->CCGR1, mask);
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_MMC
+int enable_usdhc_clk(unsigned char enable, unsigned bus_num)
+{
+ u32 mask;
+
+ if (bus_num > 3)
+ return -EINVAL;
+
+ mask = MXC_CCM_CCGR_CG_MASK << (bus_num * 2 + 2);
+ if (enable)
+ setbits_le32(&imx_ccm->CCGR6, mask);
+ else
+ clrbits_le32(&imx_ccm->CCGR6, mask);
+
+ return 0;
+}
+#endif
+
#ifdef CONFIG_SYS_I2C_MXC
/* i2c_num can be from 0 - 2 */
int enable_i2c_clk(unsigned char enable, unsigned i2c_num)
struct anatop_regs *anatop_regs =
(struct anatop_regs *)ANATOP_BASE_ADDR;
struct mxc_ccm_reg *ccm_regs = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ u32 lvds1_clk_sel;
/*
* Here be dragons!
* marked as ANATOP_MISC1 is actually documented in the PMU section
* of the datasheet as PMU_MISC1.
*
- * Switch LVDS clock source to SATA (0xb), disable clock INPUT and
- * enable clock OUTPUT. This is important for PCI express link that
- * is clocked from the i.MX6.
+ * Switch LVDS clock source to SATA (0xb) on mx6q/dl or PCI (0xa) on
+ * mx6sx, disable clock INPUT and enable clock OUTPUT. This is important
+ * for PCI express link that is clocked from the i.MX6.
*/
#define ANADIG_ANA_MISC1_LVDSCLK1_IBEN (1 << 12)
#define ANADIG_ANA_MISC1_LVDSCLK1_OBEN (1 << 10)
#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK 0x0000001F
+#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_PCIE_REF 0xa
+#define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_SATA_REF 0xb
+
+ if (is_cpu_type(MXC_CPU_MX6SX))
+ lvds1_clk_sel = ANADIG_ANA_MISC1_LVDS1_CLK_SEL_PCIE_REF;
+ else
+ lvds1_clk_sel = ANADIG_ANA_MISC1_LVDS1_CLK_SEL_SATA_REF;
+
clrsetbits_le32(&anatop_regs->ana_misc1,
ANADIG_ANA_MISC1_LVDSCLK1_IBEN |
ANADIG_ANA_MISC1_LVDS1_CLK_SEL_MASK,
- ANADIG_ANA_MISC1_LVDSCLK1_OBEN | 0xb);
+ ANADIG_ANA_MISC1_LVDSCLK1_OBEN | lvds1_clk_sel);
/* PCIe reference clock sourced from AXI. */
clrbits_le32(&ccm_regs->cbcmr, MXC_CCM_CBCMR_PCIE_AXI_CLK_SEL);
*/
#define MR(val, ba, cmd, cs1) \
((val << 16) | (1 << 15) | (cmd << 4) | (cs1 << 3) | ba)
-void mx6_dram_cfg(const struct mx6_ddr_sysinfo *i,
- const struct mx6_mmdc_calibration *c,
- const struct mx6_ddr3_cfg *m)
+void mx6_dram_cfg(const struct mx6_ddr_sysinfo *sysinfo,
+ const struct mx6_mmdc_calibration *calib,
+ const struct mx6_ddr3_cfg *ddr3_cfg)
{
volatile struct mmdc_p_regs *mmdc0;
volatile struct mmdc_p_regs *mmdc1;
- u32 reg;
+ u32 val;
u8 tcke, tcksrx, tcksre, txpdll, taofpd, taonpd, trrd;
u8 todtlon, taxpd, tanpd, tcwl, txp, tfaw, tcl;
u8 todt_idle_off = 0x4; /* from DDR3 Script Aid spreadsheet */
u16 trcd, trc, tras, twr, tmrd, trtp, trp, twtr, trfc, txs, txpr;
- u16 CS0_END;
+ u16 cs0_end;
u16 tdllk = 0x1ff; /* DLL locking time: 512 cycles (JEDEC DDR3) */
u8 coladdr;
int clkper; /* clock period in picoseconds */
clock = 400;
tcwl = 3;
}
- clkper = (1000*1000)/clock; /* ps */
+ clkper = (1000 * 1000) / clock; /* pico seconds */
todtlon = tcwl;
taxpd = tcwl;
tanpd = tcwl;
- tcwl = tcwl;
- switch (m->density) {
+ switch (ddr3_cfg->density) {
case 1: /* 1Gb per chip */
trfc = DIV_ROUND_UP(110000, clkper) - 1;
txs = DIV_ROUND_UP(120000, clkper) - 1;
break;
default:
/* invalid density */
- printf("invalid chip density\n");
+ puts("invalid chip density\n");
hang();
break;
}
txpr = txs;
- switch (m->mem_speed) {
+ switch (ddr3_cfg->mem_speed) {
case 800:
- txp = DIV_ROUND_UP(MAX(3*clkper, 7500), clkper) - 1;
- tcke = DIV_ROUND_UP(MAX(3*clkper, 7500), clkper) - 1;
- if (m->pagesz == 1) {
+ txp = DIV_ROUND_UP(max(3 * clkper, 7500), clkper) - 1;
+ tcke = DIV_ROUND_UP(max(3 * clkper, 7500), clkper) - 1;
+ if (ddr3_cfg->pagesz == 1) {
tfaw = DIV_ROUND_UP(40000, clkper) - 1;
- trrd = DIV_ROUND_UP(MAX(4*clkper, 10000), clkper) - 1;
+ trrd = DIV_ROUND_UP(max(4 * clkper, 10000), clkper) - 1;
} else {
tfaw = DIV_ROUND_UP(50000, clkper) - 1;
- trrd = DIV_ROUND_UP(MAX(4*clkper, 10000), clkper) - 1;
+ trrd = DIV_ROUND_UP(max(4 * clkper, 10000), clkper) - 1;
}
break;
case 1066:
- txp = DIV_ROUND_UP(MAX(3*clkper, 7500), clkper) - 1;
- tcke = DIV_ROUND_UP(MAX(3*clkper, 5625), clkper) - 1;
- if (m->pagesz == 1) {
+ txp = DIV_ROUND_UP(max(3 * clkper, 7500), clkper) - 1;
+ tcke = DIV_ROUND_UP(max(3 * clkper, 5625), clkper) - 1;
+ if (ddr3_cfg->pagesz == 1) {
tfaw = DIV_ROUND_UP(37500, clkper) - 1;
- trrd = DIV_ROUND_UP(MAX(4*clkper, 7500), clkper) - 1;
+ trrd = DIV_ROUND_UP(max(4 * clkper, 7500), clkper) - 1;
} else {
tfaw = DIV_ROUND_UP(50000, clkper) - 1;
- trrd = DIV_ROUND_UP(MAX(4*clkper, 10000), clkper) - 1;
+ trrd = DIV_ROUND_UP(max(4 * clkper, 10000), clkper) - 1;
}
break;
case 1333:
- txp = DIV_ROUND_UP(MAX(3*clkper, 6000), clkper) - 1;
- tcke = DIV_ROUND_UP(MAX(3*clkper, 5625), clkper) - 1;
- if (m->pagesz == 1) {
+ txp = DIV_ROUND_UP(max(3 * clkper, 6000), clkper) - 1;
+ tcke = DIV_ROUND_UP(max(3 * clkper, 5625), clkper) - 1;
+ if (ddr3_cfg->pagesz == 1) {
tfaw = DIV_ROUND_UP(30000, clkper) - 1;
- trrd = DIV_ROUND_UP(MAX(4*clkper, 6000), clkper) - 1;
+ trrd = DIV_ROUND_UP(max(4 * clkper, 6000), clkper) - 1;
} else {
tfaw = DIV_ROUND_UP(45000, clkper) - 1;
- trrd = DIV_ROUND_UP(MAX(4*clkper, 7500), clkper) - 1;
+ trrd = DIV_ROUND_UP(max(4 * clkper, 7500), clkper) - 1;
}
break;
case 1600:
- txp = DIV_ROUND_UP(MAX(3*clkper, 6000), clkper) - 1;
- tcke = DIV_ROUND_UP(MAX(3*clkper, 5000), clkper) - 1;
- if (m->pagesz == 1) {
+ txp = DIV_ROUND_UP(max(3 * clkper, 6000), clkper) - 1;
+ tcke = DIV_ROUND_UP(max(3 * clkper, 5000), clkper) - 1;
+ if (ddr3_cfg->pagesz == 1) {
tfaw = DIV_ROUND_UP(30000, clkper) - 1;
- trrd = DIV_ROUND_UP(MAX(4*clkper, 6000), clkper) - 1;
+ trrd = DIV_ROUND_UP(max(4 * clkper, 6000), clkper) - 1;
} else {
tfaw = DIV_ROUND_UP(40000, clkper) - 1;
- trrd = DIV_ROUND_UP(MAX(4*clkper, 7500), clkper) - 1;
+ trrd = DIV_ROUND_UP(max(4 * clkper, 7500), clkper) - 1;
}
break;
default:
- printf("invalid memory speed\n");
+ puts("invalid memory speed\n");
hang();
break;
}
- txpdll = DIV_ROUND_UP(MAX(10*clkper, 24000), clkper) - 1;
- tcl = DIV_ROUND_UP(m->trcd, clkper/10) - 3;
- tcksre = DIV_ROUND_UP(MAX(5*clkper, 10000), clkper);
- tcksrx = tcksre;
+ txpdll = DIV_ROUND_UP(max(10 * clkper, 24000), clkper) - 1;
+ tcksre = DIV_ROUND_UP(max(5 * clkper, 10000), clkper);
taonpd = DIV_ROUND_UP(2000, clkper) - 1;
+ tcksrx = tcksre;
taofpd = taonpd;
- trp = DIV_ROUND_UP(m->trcd, clkper/10) - 1;
+ twr = DIV_ROUND_UP(15000, clkper) - 1;
+ tmrd = DIV_ROUND_UP(max(12 * clkper, 15000), clkper) - 1;
+ trc = DIV_ROUND_UP(ddr3_cfg->trcmin, clkper / 10) - 1;
+ tras = DIV_ROUND_UP(ddr3_cfg->trasmin, clkper / 10) - 1;
+ tcl = DIV_ROUND_UP(ddr3_cfg->trcd, clkper / 10) - 3;
+ trp = DIV_ROUND_UP(ddr3_cfg->trcd, clkper / 10) - 1;
+ twtr = ROUND(max(4 * clkper, 7500) / clkper, 1) - 1;
trcd = trp;
- trc = DIV_ROUND_UP(m->trcmin, clkper/10) - 1;
- tras = DIV_ROUND_UP(m->trasmin, clkper/10) - 1;
- twr = DIV_ROUND_UP(15000, clkper) - 1;
- tmrd = DIV_ROUND_UP(MAX(12*clkper, 15000), clkper) - 1;
- twtr = ROUND(MAX(4*clkper, 7500)/clkper, 1) - 1;
trtp = twtr;
- CS0_END = ((4*i->cs_density) <= 120) ? (4*i->cs_density)+7 : 127;
- debug("density:%d Gb (%d Gb per chip)\n", i->cs_density, m->density);
+ cs0_end = 4 * sysinfo->cs_density - 1;
+
+ debug("density:%d Gb (%d Gb per chip)\n",
+ sysinfo->cs_density, ddr3_cfg->density);
debug("clock: %dMHz (%d ps)\n", clock, clkper);
- debug("memspd:%d\n", m->mem_speed);
+ debug("memspd:%d\n", ddr3_cfg->mem_speed);
debug("tcke=%d\n", tcke);
debug("tcksrx=%d\n", tcksrx);
debug("tcksre=%d\n", tcksre);
debug("twtr=%d\n", twtr);
debug("trrd=%d\n", trrd);
debug("txpr=%d\n", txpr);
- debug("CS0_END=%d\n", CS0_END);
- debug("ncs=%d\n", i->ncs);
- debug("Rtt_wr=%d\n", i->rtt_wr);
- debug("Rtt_nom=%d\n", i->rtt_nom);
- debug("SRT=%d\n", m->SRT);
+ debug("cs0_end=%d\n", cs0_end);
+ debug("ncs=%d\n", sysinfo->ncs);
+ debug("Rtt_wr=%d\n", sysinfo->rtt_wr);
+ debug("Rtt_nom=%d\n", sysinfo->rtt_nom);
+ debug("SRT=%d\n", ddr3_cfg->SRT);
debug("tcl=%d\n", tcl);
debug("twr=%d\n", twr);
* see:
* appnote, ddr3 spreadsheet
*/
- mmdc0->mpwldectrl0 = c->p0_mpwldectrl0;
- mmdc0->mpwldectrl1 = c->p0_mpwldectrl1;
- mmdc0->mpdgctrl0 = c->p0_mpdgctrl0;
- mmdc0->mpdgctrl1 = c->p0_mpdgctrl1;
- mmdc0->mprddlctl = c->p0_mprddlctl;
- mmdc0->mpwrdlctl = c->p0_mpwrdlctl;
- if (i->dsize > 1) {
- mmdc1->mpwldectrl0 = c->p1_mpwldectrl0;
- mmdc1->mpwldectrl1 = c->p1_mpwldectrl1;
- mmdc1->mpdgctrl0 = c->p1_mpdgctrl0;
- mmdc1->mpdgctrl1 = c->p1_mpdgctrl1;
- mmdc1->mprddlctl = c->p1_mprddlctl;
- mmdc1->mpwrdlctl = c->p1_mpwrdlctl;
+ mmdc0->mpwldectrl0 = calib->p0_mpwldectrl0;
+ mmdc0->mpwldectrl1 = calib->p0_mpwldectrl1;
+ mmdc0->mpdgctrl0 = calib->p0_mpdgctrl0;
+ mmdc0->mpdgctrl1 = calib->p0_mpdgctrl1;
+ mmdc0->mprddlctl = calib->p0_mprddlctl;
+ mmdc0->mpwrdlctl = calib->p0_mpwrdlctl;
+ if (sysinfo->dsize > 1) {
+ mmdc1->mpwldectrl0 = calib->p1_mpwldectrl0;
+ mmdc1->mpwldectrl1 = calib->p1_mpwldectrl1;
+ mmdc1->mpdgctrl0 = calib->p1_mpdgctrl0;
+ mmdc1->mpdgctrl1 = calib->p1_mpdgctrl1;
+ mmdc1->mprddlctl = calib->p1_mprddlctl;
+ mmdc1->mpwrdlctl = calib->p1_mpwrdlctl;
}
/* Read data DQ Byte0-3 delay */
- mmdc0->mprddqby0dl = (u32)0x33333333;
- mmdc0->mprddqby1dl = (u32)0x33333333;
- if (i->dsize > 0) {
- mmdc0->mprddqby2dl = (u32)0x33333333;
- mmdc0->mprddqby3dl = (u32)0x33333333;
+ mmdc0->mprddqby0dl = 0x33333333;
+ mmdc0->mprddqby1dl = 0x33333333;
+ if (sysinfo->dsize > 0) {
+ mmdc0->mprddqby2dl = 0x33333333;
+ mmdc0->mprddqby3dl = 0x33333333;
}
- if (i->dsize > 1) {
- mmdc1->mprddqby0dl = (u32)0x33333333;
- mmdc1->mprddqby1dl = (u32)0x33333333;
- mmdc1->mprddqby2dl = (u32)0x33333333;
- mmdc1->mprddqby3dl = (u32)0x33333333;
+
+ if (sysinfo->dsize > 1) {
+ mmdc1->mprddqby0dl = 0x33333333;
+ mmdc1->mprddqby1dl = 0x33333333;
+ mmdc1->mprddqby2dl = 0x33333333;
+ mmdc1->mprddqby3dl = 0x33333333;
}
/* MMDC Termination: rtt_nom:2 RZQ/2(120ohm), rtt_nom:1 RZQ/4(60ohm) */
- reg = (i->rtt_nom == 2) ? 0x00011117 : 0x00022227;
- mmdc0->mpodtctrl = reg;
- if (i->dsize > 1)
- mmdc1->mpodtctrl = reg;
+ val = (sysinfo->rtt_nom == 2) ? 0x00011117 : 0x00022227;
+ mmdc0->mpodtctrl = val;
+ if (sysinfo->dsize > 1)
+ mmdc1->mpodtctrl = val;
/* complete calibration */
- reg = (1 << 11); /* Force measurement on delay-lines */
- mmdc0->mpmur0 = reg;
- if (i->dsize > 1)
- mmdc1->mpmur0 = reg;
+ val = (1 << 11); /* Force measurement on delay-lines */
+ mmdc0->mpmur0 = val;
+ if (sysinfo->dsize > 1)
+ mmdc1->mpmur0 = val;
/* Step 1: configuration request */
mmdc0->mdscr = (u32)(1 << 15); /* config request */
/* Step 2: Timing configuration */
- reg = (trfc << 24) | (txs << 16) | (txp << 13) | (txpdll << 9) |
- (tfaw << 4) | tcl;
- mmdc0->mdcfg0 = reg;
- reg = (trcd << 29) | (trp << 26) | (trc << 21) | (tras << 16) |
- (1 << 15) | /* trpa */
- (twr << 9) | (tmrd << 5) | tcwl;
- mmdc0->mdcfg1 = reg;
- reg = (tdllk << 16) | (trtp << 6) | (twtr << 3) | trrd;
- mmdc0->mdcfg2 = reg;
- reg = (taofpd << 27) | (taonpd << 24) | (tanpd << 20) | (taxpd << 16) |
- (todtlon << 12) | (todt_idle_off << 4);
- mmdc0->mdotc = reg;
- mmdc0->mdasp = CS0_END; /* CS addressing */
+ mmdc0->mdcfg0 = (trfc << 24) | (txs << 16) | (txp << 13) |
+ (txpdll << 9) | (tfaw << 4) | tcl;
+ mmdc0->mdcfg1 = (trcd << 29) | (trp << 26) | (trc << 21) |
+ (tras << 16) | (1 << 15) /* trpa */ |
+ (twr << 9) | (tmrd << 5) | tcwl;
+ mmdc0->mdcfg2 = (tdllk << 16) | (trtp << 6) | (twtr << 3) | trrd;
+ mmdc0->mdotc = (taofpd << 27) | (taonpd << 24) | (tanpd << 20) |
+ (taxpd << 16) | (todtlon << 12) | (todt_idle_off << 4);
+ mmdc0->mdasp = cs0_end; /* CS addressing */
/* Step 3: Configure DDR type */
- reg = (i->cs1_mirror << 19) | (i->walat << 16) | (i->bi_on << 12) |
- (i->mif3_mode << 9) | (i->ralat << 6);
- mmdc0->mdmisc = reg;
+ mmdc0->mdmisc = (sysinfo->cs1_mirror << 19) | (sysinfo->walat << 16) |
+ (sysinfo->bi_on << 12) | (sysinfo->mif3_mode << 9) |
+ (sysinfo->ralat << 6);
/* Step 4: Configure delay while leaving reset */
- reg = (txpr << 16) | (i->sde_to_rst << 8) | (i->rst_to_cke << 0);
- mmdc0->mdor = reg;
+ mmdc0->mdor = (txpr << 16) | (sysinfo->sde_to_rst << 8) |
+ (sysinfo->rst_to_cke << 0);
/* Step 5: Configure DDR physical parameters (density and burst len) */
- coladdr = m->coladdr;
- if (m->coladdr == 8) /* 8-bit COL is 0x3 */
+ coladdr = ddr3_cfg->coladdr;
+ if (ddr3_cfg->coladdr == 8) /* 8-bit COL is 0x3 */
coladdr += 4;
- else if (m->coladdr == 12) /* 12-bit COL is 0x4 */
+ else if (ddr3_cfg->coladdr == 12) /* 12-bit COL is 0x4 */
coladdr += 1;
- reg = (m->rowaddr - 11) << 24 | /* ROW */
- (coladdr - 9) << 20 | /* COL */
- (1 << 19) | /* Burst Length = 8 for DDR3 */
- (i->dsize << 16); /* DDR data bus size */
- mmdc0->mdctl = reg;
+ mmdc0->mdctl = (ddr3_cfg->rowaddr - 11) << 24 | /* ROW */
+ (coladdr - 9) << 20 | /* COL */
+ (1 << 19) | /* Burst Length = 8 for DDR3 */
+ (sysinfo->dsize << 16); /* DDR data bus size */
/* Step 6: Perform ZQ calibration */
- reg = (u32)0xa1390001; /* one-time HW ZQ calib */
- mmdc0->mpzqhwctrl = reg;
- if (i->dsize > 1)
- mmdc1->mpzqhwctrl = reg;
+ val = 0xa1390001; /* one-time HW ZQ calib */
+ mmdc0->mpzqhwctrl = val;
+ if (sysinfo->dsize > 1)
+ mmdc1->mpzqhwctrl = val;
/* Step 7: Enable MMDC with desired chip select */
- reg = mmdc0->mdctl |
- (1 << 31) | /* SDE_0 for CS0 */
- ((i->ncs == 2) ? 1 : 0) << 30; /* SDE_1 for CS1 */
- mmdc0->mdctl = reg;
+ mmdc0->mdctl |= (1 << 31) | /* SDE_0 for CS0 */
+ ((sysinfo->ncs == 2) ? 1 : 0) << 30; /* SDE_1 for CS1 */
/* Step 8: Write Mode Registers to Init DDR3 devices */
- for (cs = 0; cs < i->ncs; cs++) {
+ for (cs = 0; cs < sysinfo->ncs; cs++) {
/* MR2 */
- reg = (i->rtt_wr & 3) << 9 | (m->SRT & 1) << 7 |
+ val = (sysinfo->rtt_wr & 3) << 9 | (ddr3_cfg->SRT & 1) << 7 |
((tcwl - 3) & 3) << 3;
- mmdc0->mdscr = (u32)MR(reg, 2, 3, cs);
+ mmdc0->mdscr = MR(val, 2, 3, cs);
/* MR3 */
- mmdc0->mdscr = (u32)MR(0, 3, 3, cs);
+ mmdc0->mdscr = MR(0, 3, 3, cs);
/* MR1 */
- reg = ((i->rtt_nom & 1) ? 1 : 0) << 2 |
- ((i->rtt_nom & 2) ? 1 : 0) << 6;
- mmdc0->mdscr = (u32)MR(reg, 1, 3, cs);
- reg = ((tcl - 1) << 4) | /* CAS */
+ val = ((sysinfo->rtt_nom & 1) ? 1 : 0) << 2 |
+ ((sysinfo->rtt_nom & 2) ? 1 : 0) << 6;
+ mmdc0->mdscr = MR(val, 1, 3, cs);
+ /* MR0 */
+ val = ((tcl - 1) << 4) | /* CAS */
(1 << 8) | /* DLL Reset */
((twr - 3) << 9); /* Write Recovery */
- /* MR0 */
- mmdc0->mdscr = (u32)MR(reg, 0, 3, cs);
+ mmdc0->mdscr = MR(val, 0, 3, cs);
/* ZQ calibration */
- reg = (1 << 10);
- mmdc0->mdscr = (u32)MR(reg, 0, 4, cs);
+ val = (1 << 10);
+ mmdc0->mdscr = MR(val, 0, 4, cs);
}
/* Step 10: Power down control and self-refresh */
- reg = (tcke & 0x7) << 16 |
- 5 << 12 | /* PWDT_1: 256 cycles */
- 5 << 8 | /* PWDT_0: 256 cycles */
- 1 << 6 | /* BOTH_CS_PD */
- (tcksrx & 0x7) << 3 |
- (tcksre & 0x7);
- mmdc0->mdpdc = reg;
- mmdc0->mapsr = (u32)0x00011006; /* ADOPT power down enabled */
+ mmdc0->mdpdc = (tcke & 0x7) << 16 |
+ 5 << 12 | /* PWDT_1: 256 cycles */
+ 5 << 8 | /* PWDT_0: 256 cycles */
+ 1 << 7 | /* SLOW_PD */
+ 1 << 6 | /* BOTH_CS_PD */
+ (tcksrx & 0x7) << 3 |
+ (tcksre & 0x7);
+ mmdc0->mapsr = 0x00001006; /* ADOPT power down enabled */
/* Step 11: Configure ZQ calibration: one-time and periodic 1ms */
- mmdc0->mpzqhwctrl = (u32)0xa1390003;
- if (i->dsize > 1)
- mmdc1->mpzqhwctrl = (u32)0xa1390003;
+ val = 0xa1390003;
+ mmdc0->mpzqhwctrl = val;
+ if (sysinfo->dsize > 1)
+ mmdc1->mpzqhwctrl = val;
/* Step 12: Configure and activate periodic refresh */
- reg = (1 << 14) | /* REF_SEL: Periodic refresh cycles of 32kHz */
- (7 << 11); /* REFR: Refresh Rate - 8 refreshes */
- mmdc0->mdref = reg;
+ mmdc0->mdref = (1 << 14) | /* REF_SEL: Periodic refresh cycle: 32kHz */
+ (7 << 11); /* REFR: Refresh Rate - 8 refreshes */
/* Step 13: Deassert config request - init complete */
- mmdc0->mdscr = (u32)0x00000000;
+ mmdc0->mdscr = 0x00000000;
/* wait for auto-ZQ calibration to complete */
mdelay(1);
/* reserved value should start rom usb */
{"usb", MAKE_CFGVAL(0x01, 0x00, 0x00, 0x00)},
{"sata", MAKE_CFGVAL(0x20, 0x00, 0x00, 0x00)},
- {"escpi1:0", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x08)},
- {"escpi1:1", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x18)},
- {"escpi1:2", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x28)},
- {"escpi1:3", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x38)},
+ {"ecspi1:0", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x08)},
+ {"ecspi1:1", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x18)},
+ {"ecspi1:2", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x28)},
+ {"ecspi1:3", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x38)},
/* 4 bit bus width */
{"esdhc1", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)},
{"esdhc2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
}
#endif
+ /* Must disable the L2 before changing the latency parameters */
+ clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
+
writel(0x132, &pl310->pl310_tag_latency_ctrl);
writel(0x132, &pl310->pl310_data_latency_ctrl);
--- /dev/null
+menu "Panasonic UniPhier platform"
+ depends on ARCH_UNIPHIER
+
+config SYS_CPU
+ string
+ default "armv7"
+
+config SYS_SOC
+ string
+ default "uniphier"
+
+config SYS_CONFIG_NAME
+ string
+ default "ph1_pro4" if MACH_PH1_PRO4
+ default "ph1_ld4" if MACH_PH1_LD4
+ default "ph1_sld8" if MACH_PH1_SLD8
+
+choice
+ prompt "UniPhier SoC select"
+
+config MACH_PH1_PRO4
+ bool "PH1-Pro4"
+
+config MACH_PH1_LD4
+ bool "PH1-LD4"
+
+config MACH_PH1_SLD8
+ bool "PH1-sLD8"
+
+endchoice
+
+endmenu
--- /dev/null
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-$(CONFIG_SPL_BUILD) += lowlevel_init.o init_page_table.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
+
+obj-y += timer.o
+obj-y += reset.o
+obj-y += cache_uniphier.o
+obj-y += dram_init.o
+obj-$(CONFIG_DISPLAY_CPUINFO) += cpu_info.o
+obj-$(CONFIG_BOARD_LATE_INIT) += board_late_init.o
+obj-$(CONFIG_UNIPHIER_SMP) += smp.o
+obj-$(if $(CONFIG_SPL_BUILD),,y) += cmd_pinmon.o
+
+obj-y += board_common.o
+obj-$(CONFIG_PFC_MICRO_SUPPORT_CARD) += support_card.o
+obj-$(CONFIG_DCC_MICRO_SUPPORT_CARD) += support_card.o
+
+obj-$(CONFIG_MACH_PH1_LD4) += ph1-ld4/
+obj-$(CONFIG_MACH_PH1_PRO4) += ph1-pro4/
+obj-$(CONFIG_MACH_PH1_SLD8) += ph1-sld8/
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/led.h>
+
+/*
+ * Routine: board_init
+ * Description: Early hardware init.
+ */
+int board_init(void)
+{
+ led_write(U, B, O, O);
+
+ return 0;
+}
+
+#if CONFIG_NR_DRAM_BANKS >= 2
+void dram_init_banksize(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ gd->bd->bi_dram[0].start = CONFIG_SDRAM0_BASE;
+ gd->bd->bi_dram[0].size = CONFIG_SDRAM0_SIZE;
+ gd->bd->bi_dram[1].start = CONFIG_SDRAM1_BASE;
+ gd->bd->bi_dram[1].size = CONFIG_SDRAM1_SIZE;
+}
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <nand.h>
+#include <asm/io.h>
+#include <../drivers/mtd/nand/denali.h>
+
+static void nand_denali_wp_disable(void)
+{
+#ifdef CONFIG_NAND_DENALI
+ /*
+ * Since the boot rom enables the write protection for NAND boot mode,
+ * it must be disabled somewhere for "nand write", "nand erase", etc.
+ * The workaround is here to not disturb the Denali NAND controller
+ * driver just for a really SoC-specific thing.
+ */
+ void __iomem *denali_reg = (void __iomem *)CONFIG_SYS_NAND_REGS_BASE;
+
+ writel(WRITE_PROTECT__FLAG, denali_reg + WRITE_PROTECT);
+#endif
+}
+
+static void nand_denali_fixup(void)
+{
+#if defined(CONFIG_NAND_DENALI) && \
+ (defined(CONFIG_MACH_PH1_SLD8) || defined(CONFIG_MACH_PH1_PRO4))
+ /*
+ * The Denali NAND controller on some of UniPhier SoCs does not
+ * automatically query the device parameters. For those SoCs,
+ * some registers must be set after the device is probed.
+ */
+ void __iomem *denali_reg = (void __iomem *)CONFIG_SYS_NAND_REGS_BASE;
+ struct mtd_info *mtd;
+ struct nand_chip *chip;
+
+ if (nand_curr_device < 0 ||
+ nand_curr_device >= CONFIG_SYS_MAX_NAND_DEVICE) {
+ /* NAND was not detected. Just return. */
+ return;
+ }
+
+ mtd = &nand_info[nand_curr_device];
+ chip = mtd->priv;
+
+ writel(mtd->erasesize / mtd->writesize, denali_reg + PAGES_PER_BLOCK);
+ writel(0, denali_reg + DEVICE_WIDTH);
+ writel(mtd->writesize, denali_reg + DEVICE_MAIN_AREA_SIZE);
+ writel(mtd->oobsize, denali_reg + DEVICE_SPARE_AREA_SIZE);
+ writel(1, denali_reg + DEVICES_CONNECTED);
+
+ /*
+ * chip->scan_bbt in nand_scan_tail() has been skipped.
+ * It should be done in here.
+ */
+ chip->scan_bbt(mtd);
+#endif
+}
+
+int board_late_init(void)
+{
+ puts("MODE: ");
+
+ switch (spl_boot_device()) {
+ case BOOT_DEVICE_MMC1:
+ printf("eMMC Boot\n");
+ setenv("bootmode", "emmcboot");
+ nand_denali_fixup();
+ break;
+ case BOOT_DEVICE_NAND:
+ printf("NAND Boot\n");
+ setenv("bootmode", "nandboot");
+ nand_denali_wp_disable();
+ break;
+ case BOOT_DEVICE_NOR:
+ printf("NOR Boot\n");
+ setenv("bootmode", "norboot");
+ nand_denali_fixup();
+ break;
+ default:
+ printf("Unsupported Boot Mode\n");
+ return -1;
+ }
+
+ return 0;
+}
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/armv7.h>
+#include <asm/arch/ssc-regs.h>
+
+#ifdef CONFIG_UNIPHIER_L2CACHE_ON
+static void uniphier_cache_maint_all(u32 operation)
+{
+ /* try until the command is successfully set */
+ do {
+ writel(SSCOQM_S_ALL | SSCOQM_CE | operation, SSCOQM);
+ } while (readl(SSCOPPQSEF) & (SSCOPPQSEF_FE | SSCOPPQSEF_OE));
+
+ /* wait until the operation is completed */
+ while (readl(SSCOLPQS) != SSCOLPQS_EF)
+ ;
+
+ /* clear the complete notification flag */
+ writel(SSCOLPQS_EF, SSCOLPQS);
+
+ writel(SSCOPE_CM_SYNC, SSCOPE); /* drain internal buffers */
+ readl(SSCOPE); /* need a read back to confirm */
+}
+
+void v7_outer_cache_flush_all(void)
+{
+ uniphier_cache_maint_all(SSCOQM_CM_WB_INV);
+}
+
+void v7_outer_cache_inval_all(void)
+{
+ uniphier_cache_maint_all(SSCOQM_CM_INV);
+}
+
+static void __uniphier_cache_maint_range(u32 start, u32 size, u32 operation)
+{
+ /* try until the command is successfully set */
+ do {
+ writel(SSCOQM_S_ADDRESS | SSCOQM_CE | operation, SSCOQM);
+ writel(start, SSCOQAD);
+ writel(size, SSCOQSZ);
+
+ } while (readl(SSCOPPQSEF) & (SSCOPPQSEF_FE | SSCOPPQSEF_OE));
+
+ /* wait until the operation is completed */
+ while (readl(SSCOLPQS) != SSCOLPQS_EF)
+ ;
+
+ /* clear the complete notification flag */
+ writel(SSCOLPQS_EF, SSCOLPQS);
+}
+
+static void uniphier_cache_maint_range(u32 start, u32 end, u32 operation)
+{
+ u32 size;
+
+ /*
+ * If start address is not aligned to cache-line,
+ * do cache operation for the first cache-line
+ */
+ start = start & ~(SSC_LINE_SIZE - 1);
+
+ if (start == 0 && end >= (u32)(-SSC_LINE_SIZE)) {
+ /* this means cache operation for all range */
+ uniphier_cache_maint_all(operation);
+ return;
+ }
+
+ /*
+ * If end address is not aligned to cache-line,
+ * do cache operation for the last cache-line
+ */
+ size = (end - start + SSC_LINE_SIZE - 1) & ~(SSC_LINE_SIZE - 1);
+
+ while (size) {
+ u32 chunk_size = size > SSC_RANGE_OP_MAX_SIZE ?
+ SSC_RANGE_OP_MAX_SIZE : size;
+ __uniphier_cache_maint_range(start, chunk_size, operation);
+
+ start += chunk_size;
+ size -= chunk_size;
+ }
+
+ writel(SSCOPE_CM_SYNC, SSCOPE); /* drain internal buffers */
+ readl(SSCOPE); /* need a read back to confirm */
+}
+
+void v7_outer_cache_flush_range(u32 start, u32 end)
+{
+ uniphier_cache_maint_range(start, end, SSCOQM_CM_WB_INV);
+}
+
+void v7_outer_cache_inval_range(u32 start, u32 end)
+{
+ uniphier_cache_maint_range(start, end, SSCOQM_CM_INV);
+}
+
+void v7_outer_cache_enable(void)
+{
+ u32 tmp;
+ tmp = readl(SSCC);
+ tmp |= SSCC_ON;
+ writel(tmp, SSCC);
+}
+#endif
+
+void v7_outer_cache_disable(void)
+{
+ u32 tmp;
+ tmp = readl(SSCC);
+ tmp &= ~SSCC_ON;
+ writel(tmp, SSCC);
+}
+
+void wakeup_secondary(void);
+
+void enable_caches(void)
+{
+ uint32_t reg;
+
+#ifdef CONFIG_UNIPHIER_SMP
+ /*
+ * The secondary CPU must move to DDR,
+ * before L2 disable.
+ * On SPL, the Page Table is located on the L2.
+ */
+ wakeup_secondary();
+#endif
+ /*
+ * UniPhier SoCs must use L2 cache for init stack pointer.
+ * We disable L2 and L1 in this order.
+ * If CONFIG_SYS_DCACHE_OFF is not defined,
+ * caches are enabled again with a new page table.
+ */
+
+ /* L2 disable */
+ v7_outer_cache_disable();
+
+ /* L1 disable */
+ reg = get_cr();
+ reg &= ~(CR_C | CR_M);
+ set_cr(reg);
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+ dcache_enable();
+#endif
+}
--- /dev/null
+/*
+ * Copyright (C) 2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/boot-device.h>
+
+static int do_pinmon(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ struct boot_device_info *table;
+ u32 mode_sel, n = 0;
+
+ mode_sel = get_boot_mode_sel();
+
+ puts("Boot Mode Pin:\n");
+
+ for (table = boot_device_table; strlen(table->info); table++) {
+ printf(" %c %02x %s\n", n == mode_sel ? '*' : ' ', n,
+ table->info);
+ n++;
+ }
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ pinmon, 1, 1, do_pinmon,
+ "pin monitor",
+ ""
+);
--- /dev/null
+/*
+ * Copyright (C) 2013-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sg-regs.h>
+
+int print_cpuinfo(void)
+{
+ u32 revision, type, model, rev, required_model = 1, required_rev = 1;
+
+ revision = readl(SG_REVISION);
+ type = (revision & SG_REVISION_TYPE_MASK) >> SG_REVISION_TYPE_SHIFT;
+ model = (revision & SG_REVISION_MODEL_MASK) >> SG_REVISION_MODEL_SHIFT;
+ rev = (revision & SG_REVISION_REV_MASK) >> SG_REVISION_REV_SHIFT;
+
+ puts("CPU: ");
+
+ switch (type) {
+ case 0x25:
+ puts("PH1-sLD3 (MN2WS0220)");
+ required_model = 2;
+ break;
+ case 0x26:
+ puts("PH1-LD4 (MN2WS0250)");
+ required_rev = 2;
+ break;
+ case 0x28:
+ puts("PH1-Pro4 (MN2WS0230)");
+ break;
+ case 0x29:
+ puts("PH1-sLD8 (MN2WS0270)");
+ break;
+ default:
+ printf("Unknown Processor ID (0x%x)\n", revision);
+ return -1;
+ }
+
+ if (model > 1)
+ printf(" model %d", model);
+
+ printf(" (rev. %d)\n", rev);
+
+ if (model < required_model) {
+ printf("Sorry, this model is not supported.\n");
+ printf("Required model is %d.", required_model);
+ return -1;
+ } else if (rev < required_rev) {
+ printf("Sorry, this revision is not supported.\n");
+ printf("Required revision is %d.", required_rev);
+ return -1;
+ }
+
+ return 0;
+}
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/led.h>
+
+int umc_init(void);
+void enable_dpll_ssc(void);
+
+int dram_init(void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+ gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
+
+#if !defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)
+ led_write(B, 4, , );
+
+ {
+ int res;
+
+ res = umc_init();
+ if (res < 0)
+ return res;
+ }
+ led_write(B, 5, , );
+
+ enable_dpll_ssc();
+#endif
+
+ led_write(B, 6, , );
+
+ return 0;
+}
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+
+/* encoding without TEX remap */
+#define NO_MAP 0x00000000 /* No Map */
+#define DEVICE 0x00002002 /* Non-shareable Device */
+#define NORMAL 0x0000000e /* Normal Memory Write-Back, No Write-Allocate */
+
+#define SSC NORMAL /* System Cache: Normal */
+#define EXT DEVICE /* External Bus: Device */
+#define REG DEVICE /* IO Register: Device */
+#define DDR DEVICE /* DDR SDRAM: Device */
+
+#ifdef CONFIG_SPL_BUILD
+#define IS_SPL_TEXT_AREA(x) ((x) == ((CONFIG_SPL_TEXT_BASE) >> 20))
+#else
+#define IS_SPL_TEXT_AREA(x) ((x) == ((CONFIG_SYS_TEXT_BASE) >> 20))
+#endif
+
+#define IS_INIT_STACK_AREA(x) ((x) == ((CONFIG_SYS_INIT_SP_ADDR) >> 20))
+
+#define IS_SSC(x) ((IS_SPL_TEXT_AREA(x)) || \
+ (IS_INIT_STACK_AREA(x)))
+#define IS_EXT(x) ((x) < 0x100)
+#define IS_REG(x) (0x500 <= (x) && (x) < 0x700)
+#define IS_DDR(x) (0x800 <= (x) && (x) < 0xf00)
+
+#define MMU_FLAGS(x) (IS_SSC(x)) ? SSC : \
+ (IS_EXT(x)) ? EXT : \
+ (IS_REG(x)) ? REG : \
+ (IS_DDR(x)) ? DDR : \
+ NO_MAP
+
+#define TBL_ENTRY(x) (((x) << 20) | (MMU_FLAGS(x)))
+
+const u32 __aligned(PGTABLE_SIZE) init_page_table[PGTABLE_SIZE / sizeof(u32)]
+ = {
+ TBL_ENTRY(0x000), TBL_ENTRY(0x001), TBL_ENTRY(0x002), TBL_ENTRY(0x003),
+ TBL_ENTRY(0x004), TBL_ENTRY(0x005), TBL_ENTRY(0x006), TBL_ENTRY(0x007),
+ TBL_ENTRY(0x008), TBL_ENTRY(0x009), TBL_ENTRY(0x00a), TBL_ENTRY(0x00b),
+ TBL_ENTRY(0x00c), TBL_ENTRY(0x00d), TBL_ENTRY(0x00e), TBL_ENTRY(0x00f),
+ TBL_ENTRY(0x010), TBL_ENTRY(0x011), TBL_ENTRY(0x012), TBL_ENTRY(0x013),
+ TBL_ENTRY(0x014), TBL_ENTRY(0x015), TBL_ENTRY(0x016), TBL_ENTRY(0x017),
+ TBL_ENTRY(0x018), TBL_ENTRY(0x019), TBL_ENTRY(0x01a), TBL_ENTRY(0x01b),
+ TBL_ENTRY(0x01c), TBL_ENTRY(0x01d), TBL_ENTRY(0x01e), TBL_ENTRY(0x01f),
+ TBL_ENTRY(0x020), TBL_ENTRY(0x021), TBL_ENTRY(0x022), TBL_ENTRY(0x023),
+ TBL_ENTRY(0x024), TBL_ENTRY(0x025), TBL_ENTRY(0x026), TBL_ENTRY(0x027),
+ TBL_ENTRY(0x028), TBL_ENTRY(0x029), TBL_ENTRY(0x02a), TBL_ENTRY(0x02b),
+ TBL_ENTRY(0x02c), TBL_ENTRY(0x02d), TBL_ENTRY(0x02e), TBL_ENTRY(0x02f),
+ TBL_ENTRY(0x030), TBL_ENTRY(0x031), TBL_ENTRY(0x032), TBL_ENTRY(0x033),
+ TBL_ENTRY(0x034), TBL_ENTRY(0x035), TBL_ENTRY(0x036), TBL_ENTRY(0x037),
+ TBL_ENTRY(0x038), TBL_ENTRY(0x039), TBL_ENTRY(0x03a), TBL_ENTRY(0x03b),
+ TBL_ENTRY(0x03c), TBL_ENTRY(0x03d), TBL_ENTRY(0x03e), TBL_ENTRY(0x03f),
+ TBL_ENTRY(0x040), TBL_ENTRY(0x041), TBL_ENTRY(0x042), TBL_ENTRY(0x043),
+ TBL_ENTRY(0x044), TBL_ENTRY(0x045), TBL_ENTRY(0x046), TBL_ENTRY(0x047),
+ TBL_ENTRY(0x048), TBL_ENTRY(0x049), TBL_ENTRY(0x04a), TBL_ENTRY(0x04b),
+ TBL_ENTRY(0x04c), TBL_ENTRY(0x04d), TBL_ENTRY(0x04e), TBL_ENTRY(0x04f),
+ TBL_ENTRY(0x050), TBL_ENTRY(0x051), TBL_ENTRY(0x052), TBL_ENTRY(0x053),
+ TBL_ENTRY(0x054), TBL_ENTRY(0x055), TBL_ENTRY(0x056), TBL_ENTRY(0x057),
+ TBL_ENTRY(0x058), TBL_ENTRY(0x059), TBL_ENTRY(0x05a), TBL_ENTRY(0x05b),
+ TBL_ENTRY(0x05c), TBL_ENTRY(0x05d), TBL_ENTRY(0x05e), TBL_ENTRY(0x05f),
+ TBL_ENTRY(0x060), TBL_ENTRY(0x061), TBL_ENTRY(0x062), TBL_ENTRY(0x063),
+ TBL_ENTRY(0x064), TBL_ENTRY(0x065), TBL_ENTRY(0x066), TBL_ENTRY(0x067),
+ TBL_ENTRY(0x068), TBL_ENTRY(0x069), TBL_ENTRY(0x06a), TBL_ENTRY(0x06b),
+ TBL_ENTRY(0x06c), TBL_ENTRY(0x06d), TBL_ENTRY(0x06e), TBL_ENTRY(0x06f),
+ TBL_ENTRY(0x070), TBL_ENTRY(0x071), TBL_ENTRY(0x072), TBL_ENTRY(0x073),
+ TBL_ENTRY(0x074), TBL_ENTRY(0x075), TBL_ENTRY(0x076), TBL_ENTRY(0x077),
+ TBL_ENTRY(0x078), TBL_ENTRY(0x079), TBL_ENTRY(0x07a), TBL_ENTRY(0x07b),
+ TBL_ENTRY(0x07c), TBL_ENTRY(0x07d), TBL_ENTRY(0x07e), TBL_ENTRY(0x07f),
+ TBL_ENTRY(0x080), TBL_ENTRY(0x081), TBL_ENTRY(0x082), TBL_ENTRY(0x083),
+ TBL_ENTRY(0x084), TBL_ENTRY(0x085), TBL_ENTRY(0x086), TBL_ENTRY(0x087),
+ TBL_ENTRY(0x088), TBL_ENTRY(0x089), TBL_ENTRY(0x08a), TBL_ENTRY(0x08b),
+ TBL_ENTRY(0x08c), TBL_ENTRY(0x08d), TBL_ENTRY(0x08e), TBL_ENTRY(0x08f),
+ TBL_ENTRY(0x090), TBL_ENTRY(0x091), TBL_ENTRY(0x092), TBL_ENTRY(0x093),
+ TBL_ENTRY(0x094), TBL_ENTRY(0x095), TBL_ENTRY(0x096), TBL_ENTRY(0x097),
+ TBL_ENTRY(0x098), TBL_ENTRY(0x099), TBL_ENTRY(0x09a), TBL_ENTRY(0x09b),
+ TBL_ENTRY(0x09c), TBL_ENTRY(0x09d), TBL_ENTRY(0x09e), TBL_ENTRY(0x09f),
+ TBL_ENTRY(0x0a0), TBL_ENTRY(0x0a1), TBL_ENTRY(0x0a2), TBL_ENTRY(0x0a3),
+ TBL_ENTRY(0x0a4), TBL_ENTRY(0x0a5), TBL_ENTRY(0x0a6), TBL_ENTRY(0x0a7),
+ TBL_ENTRY(0x0a8), TBL_ENTRY(0x0a9), TBL_ENTRY(0x0aa), TBL_ENTRY(0x0ab),
+ TBL_ENTRY(0x0ac), TBL_ENTRY(0x0ad), TBL_ENTRY(0x0ae), TBL_ENTRY(0x0af),
+ TBL_ENTRY(0x0b0), TBL_ENTRY(0x0b1), TBL_ENTRY(0x0b2), TBL_ENTRY(0x0b3),
+ TBL_ENTRY(0x0b4), TBL_ENTRY(0x0b5), TBL_ENTRY(0x0b6), TBL_ENTRY(0x0b7),
+ TBL_ENTRY(0x0b8), TBL_ENTRY(0x0b9), TBL_ENTRY(0x0ba), TBL_ENTRY(0x0bb),
+ TBL_ENTRY(0x0bc), TBL_ENTRY(0x0bd), TBL_ENTRY(0x0be), TBL_ENTRY(0x0bf),
+ TBL_ENTRY(0x0c0), TBL_ENTRY(0x0c1), TBL_ENTRY(0x0c2), TBL_ENTRY(0x0c3),
+ TBL_ENTRY(0x0c4), TBL_ENTRY(0x0c5), TBL_ENTRY(0x0c6), TBL_ENTRY(0x0c7),
+ TBL_ENTRY(0x0c8), TBL_ENTRY(0x0c9), TBL_ENTRY(0x0ca), TBL_ENTRY(0x0cb),
+ TBL_ENTRY(0x0cc), TBL_ENTRY(0x0cd), TBL_ENTRY(0x0ce), TBL_ENTRY(0x0cf),
+ TBL_ENTRY(0x0d0), TBL_ENTRY(0x0d1), TBL_ENTRY(0x0d2), TBL_ENTRY(0x0d3),
+ TBL_ENTRY(0x0d4), TBL_ENTRY(0x0d5), TBL_ENTRY(0x0d6), TBL_ENTRY(0x0d7),
+ TBL_ENTRY(0x0d8), TBL_ENTRY(0x0d9), TBL_ENTRY(0x0da), TBL_ENTRY(0x0db),
+ TBL_ENTRY(0x0dc), TBL_ENTRY(0x0dd), TBL_ENTRY(0x0de), TBL_ENTRY(0x0df),
+ TBL_ENTRY(0x0e0), TBL_ENTRY(0x0e1), TBL_ENTRY(0x0e2), TBL_ENTRY(0x0e3),
+ TBL_ENTRY(0x0e4), TBL_ENTRY(0x0e5), TBL_ENTRY(0x0e6), TBL_ENTRY(0x0e7),
+ TBL_ENTRY(0x0e8), TBL_ENTRY(0x0e9), TBL_ENTRY(0x0ea), TBL_ENTRY(0x0eb),
+ TBL_ENTRY(0x0ec), TBL_ENTRY(0x0ed), TBL_ENTRY(0x0ee), TBL_ENTRY(0x0ef),
+ TBL_ENTRY(0x0f0), TBL_ENTRY(0x0f1), TBL_ENTRY(0x0f2), TBL_ENTRY(0x0f3),
+ TBL_ENTRY(0x0f4), TBL_ENTRY(0x0f5), TBL_ENTRY(0x0f6), TBL_ENTRY(0x0f7),
+ TBL_ENTRY(0x0f8), TBL_ENTRY(0x0f9), TBL_ENTRY(0x0fa), TBL_ENTRY(0x0fb),
+ TBL_ENTRY(0x0fc), TBL_ENTRY(0x0fd), TBL_ENTRY(0x0fe), TBL_ENTRY(0x0ff),
+ TBL_ENTRY(0x100), TBL_ENTRY(0x101), TBL_ENTRY(0x102), TBL_ENTRY(0x103),
+ TBL_ENTRY(0x104), TBL_ENTRY(0x105), TBL_ENTRY(0x106), TBL_ENTRY(0x107),
+ TBL_ENTRY(0x108), TBL_ENTRY(0x109), TBL_ENTRY(0x10a), TBL_ENTRY(0x10b),
+ TBL_ENTRY(0x10c), TBL_ENTRY(0x10d), TBL_ENTRY(0x10e), TBL_ENTRY(0x10f),
+ TBL_ENTRY(0x110), TBL_ENTRY(0x111), TBL_ENTRY(0x112), TBL_ENTRY(0x113),
+ TBL_ENTRY(0x114), TBL_ENTRY(0x115), TBL_ENTRY(0x116), TBL_ENTRY(0x117),
+ TBL_ENTRY(0x118), TBL_ENTRY(0x119), TBL_ENTRY(0x11a), TBL_ENTRY(0x11b),
+ TBL_ENTRY(0x11c), TBL_ENTRY(0x11d), TBL_ENTRY(0x11e), TBL_ENTRY(0x11f),
+ TBL_ENTRY(0x120), TBL_ENTRY(0x121), TBL_ENTRY(0x122), TBL_ENTRY(0x123),
+ TBL_ENTRY(0x124), TBL_ENTRY(0x125), TBL_ENTRY(0x126), TBL_ENTRY(0x127),
+ TBL_ENTRY(0x128), TBL_ENTRY(0x129), TBL_ENTRY(0x12a), TBL_ENTRY(0x12b),
+ TBL_ENTRY(0x12c), TBL_ENTRY(0x12d), TBL_ENTRY(0x12e), TBL_ENTRY(0x12f),
+ TBL_ENTRY(0x130), TBL_ENTRY(0x131), TBL_ENTRY(0x132), TBL_ENTRY(0x133),
+ TBL_ENTRY(0x134), TBL_ENTRY(0x135), TBL_ENTRY(0x136), TBL_ENTRY(0x137),
+ TBL_ENTRY(0x138), TBL_ENTRY(0x139), TBL_ENTRY(0x13a), TBL_ENTRY(0x13b),
+ TBL_ENTRY(0x13c), TBL_ENTRY(0x13d), TBL_ENTRY(0x13e), TBL_ENTRY(0x13f),
+ TBL_ENTRY(0x140), TBL_ENTRY(0x141), TBL_ENTRY(0x142), TBL_ENTRY(0x143),
+ TBL_ENTRY(0x144), TBL_ENTRY(0x145), TBL_ENTRY(0x146), TBL_ENTRY(0x147),
+ TBL_ENTRY(0x148), TBL_ENTRY(0x149), TBL_ENTRY(0x14a), TBL_ENTRY(0x14b),
+ TBL_ENTRY(0x14c), TBL_ENTRY(0x14d), TBL_ENTRY(0x14e), TBL_ENTRY(0x14f),
+ TBL_ENTRY(0x150), TBL_ENTRY(0x151), TBL_ENTRY(0x152), TBL_ENTRY(0x153),
+ TBL_ENTRY(0x154), TBL_ENTRY(0x155), TBL_ENTRY(0x156), TBL_ENTRY(0x157),
+ TBL_ENTRY(0x158), TBL_ENTRY(0x159), TBL_ENTRY(0x15a), TBL_ENTRY(0x15b),
+ TBL_ENTRY(0x15c), TBL_ENTRY(0x15d), TBL_ENTRY(0x15e), TBL_ENTRY(0x15f),
+ TBL_ENTRY(0x160), TBL_ENTRY(0x161), TBL_ENTRY(0x162), TBL_ENTRY(0x163),
+ TBL_ENTRY(0x164), TBL_ENTRY(0x165), TBL_ENTRY(0x166), TBL_ENTRY(0x167),
+ TBL_ENTRY(0x168), TBL_ENTRY(0x169), TBL_ENTRY(0x16a), TBL_ENTRY(0x16b),
+ TBL_ENTRY(0x16c), TBL_ENTRY(0x16d), TBL_ENTRY(0x16e), TBL_ENTRY(0x16f),
+ TBL_ENTRY(0x170), TBL_ENTRY(0x171), TBL_ENTRY(0x172), TBL_ENTRY(0x173),
+ TBL_ENTRY(0x174), TBL_ENTRY(0x175), TBL_ENTRY(0x176), TBL_ENTRY(0x177),
+ TBL_ENTRY(0x178), TBL_ENTRY(0x179), TBL_ENTRY(0x17a), TBL_ENTRY(0x17b),
+ TBL_ENTRY(0x17c), TBL_ENTRY(0x17d), TBL_ENTRY(0x17e), TBL_ENTRY(0x17f),
+ TBL_ENTRY(0x180), TBL_ENTRY(0x181), TBL_ENTRY(0x182), TBL_ENTRY(0x183),
+ TBL_ENTRY(0x184), TBL_ENTRY(0x185), TBL_ENTRY(0x186), TBL_ENTRY(0x187),
+ TBL_ENTRY(0x188), TBL_ENTRY(0x189), TBL_ENTRY(0x18a), TBL_ENTRY(0x18b),
+ TBL_ENTRY(0x18c), TBL_ENTRY(0x18d), TBL_ENTRY(0x18e), TBL_ENTRY(0x18f),
+ TBL_ENTRY(0x190), TBL_ENTRY(0x191), TBL_ENTRY(0x192), TBL_ENTRY(0x193),
+ TBL_ENTRY(0x194), TBL_ENTRY(0x195), TBL_ENTRY(0x196), TBL_ENTRY(0x197),
+ TBL_ENTRY(0x198), TBL_ENTRY(0x199), TBL_ENTRY(0x19a), TBL_ENTRY(0x19b),
+ TBL_ENTRY(0x19c), TBL_ENTRY(0x19d), TBL_ENTRY(0x19e), TBL_ENTRY(0x19f),
+ TBL_ENTRY(0x1a0), TBL_ENTRY(0x1a1), TBL_ENTRY(0x1a2), TBL_ENTRY(0x1a3),
+ TBL_ENTRY(0x1a4), TBL_ENTRY(0x1a5), TBL_ENTRY(0x1a6), TBL_ENTRY(0x1a7),
+ TBL_ENTRY(0x1a8), TBL_ENTRY(0x1a9), TBL_ENTRY(0x1aa), TBL_ENTRY(0x1ab),
+ TBL_ENTRY(0x1ac), TBL_ENTRY(0x1ad), TBL_ENTRY(0x1ae), TBL_ENTRY(0x1af),
+ TBL_ENTRY(0x1b0), TBL_ENTRY(0x1b1), TBL_ENTRY(0x1b2), TBL_ENTRY(0x1b3),
+ TBL_ENTRY(0x1b4), TBL_ENTRY(0x1b5), TBL_ENTRY(0x1b6), TBL_ENTRY(0x1b7),
+ TBL_ENTRY(0x1b8), TBL_ENTRY(0x1b9), TBL_ENTRY(0x1ba), TBL_ENTRY(0x1bb),
+ TBL_ENTRY(0x1bc), TBL_ENTRY(0x1bd), TBL_ENTRY(0x1be), TBL_ENTRY(0x1bf),
+ TBL_ENTRY(0x1c0), TBL_ENTRY(0x1c1), TBL_ENTRY(0x1c2), TBL_ENTRY(0x1c3),
+ TBL_ENTRY(0x1c4), TBL_ENTRY(0x1c5), TBL_ENTRY(0x1c6), TBL_ENTRY(0x1c7),
+ TBL_ENTRY(0x1c8), TBL_ENTRY(0x1c9), TBL_ENTRY(0x1ca), TBL_ENTRY(0x1cb),
+ TBL_ENTRY(0x1cc), TBL_ENTRY(0x1cd), TBL_ENTRY(0x1ce), TBL_ENTRY(0x1cf),
+ TBL_ENTRY(0x1d0), TBL_ENTRY(0x1d1), TBL_ENTRY(0x1d2), TBL_ENTRY(0x1d3),
+ TBL_ENTRY(0x1d4), TBL_ENTRY(0x1d5), TBL_ENTRY(0x1d6), TBL_ENTRY(0x1d7),
+ TBL_ENTRY(0x1d8), TBL_ENTRY(0x1d9), TBL_ENTRY(0x1da), TBL_ENTRY(0x1db),
+ TBL_ENTRY(0x1dc), TBL_ENTRY(0x1dd), TBL_ENTRY(0x1de), TBL_ENTRY(0x1df),
+ TBL_ENTRY(0x1e0), TBL_ENTRY(0x1e1), TBL_ENTRY(0x1e2), TBL_ENTRY(0x1e3),
+ TBL_ENTRY(0x1e4), TBL_ENTRY(0x1e5), TBL_ENTRY(0x1e6), TBL_ENTRY(0x1e7),
+ TBL_ENTRY(0x1e8), TBL_ENTRY(0x1e9), TBL_ENTRY(0x1ea), TBL_ENTRY(0x1eb),
+ TBL_ENTRY(0x1ec), TBL_ENTRY(0x1ed), TBL_ENTRY(0x1ee), TBL_ENTRY(0x1ef),
+ TBL_ENTRY(0x1f0), TBL_ENTRY(0x1f1), TBL_ENTRY(0x1f2), TBL_ENTRY(0x1f3),
+ TBL_ENTRY(0x1f4), TBL_ENTRY(0x1f5), TBL_ENTRY(0x1f6), TBL_ENTRY(0x1f7),
+ TBL_ENTRY(0x1f8), TBL_ENTRY(0x1f9), TBL_ENTRY(0x1fa), TBL_ENTRY(0x1fb),
+ TBL_ENTRY(0x1fc), TBL_ENTRY(0x1fd), TBL_ENTRY(0x1fe), TBL_ENTRY(0x1ff),
+ TBL_ENTRY(0x200), TBL_ENTRY(0x201), TBL_ENTRY(0x202), TBL_ENTRY(0x203),
+ TBL_ENTRY(0x204), TBL_ENTRY(0x205), TBL_ENTRY(0x206), TBL_ENTRY(0x207),
+ TBL_ENTRY(0x208), TBL_ENTRY(0x209), TBL_ENTRY(0x20a), TBL_ENTRY(0x20b),
+ TBL_ENTRY(0x20c), TBL_ENTRY(0x20d), TBL_ENTRY(0x20e), TBL_ENTRY(0x20f),
+ TBL_ENTRY(0x210), TBL_ENTRY(0x211), TBL_ENTRY(0x212), TBL_ENTRY(0x213),
+ TBL_ENTRY(0x214), TBL_ENTRY(0x215), TBL_ENTRY(0x216), TBL_ENTRY(0x217),
+ TBL_ENTRY(0x218), TBL_ENTRY(0x219), TBL_ENTRY(0x21a), TBL_ENTRY(0x21b),
+ TBL_ENTRY(0x21c), TBL_ENTRY(0x21d), TBL_ENTRY(0x21e), TBL_ENTRY(0x21f),
+ TBL_ENTRY(0x220), TBL_ENTRY(0x221), TBL_ENTRY(0x222), TBL_ENTRY(0x223),
+ TBL_ENTRY(0x224), TBL_ENTRY(0x225), TBL_ENTRY(0x226), TBL_ENTRY(0x227),
+ TBL_ENTRY(0x228), TBL_ENTRY(0x229), TBL_ENTRY(0x22a), TBL_ENTRY(0x22b),
+ TBL_ENTRY(0x22c), TBL_ENTRY(0x22d), TBL_ENTRY(0x22e), TBL_ENTRY(0x22f),
+ TBL_ENTRY(0x230), TBL_ENTRY(0x231), TBL_ENTRY(0x232), TBL_ENTRY(0x233),
+ TBL_ENTRY(0x234), TBL_ENTRY(0x235), TBL_ENTRY(0x236), TBL_ENTRY(0x237),
+ TBL_ENTRY(0x238), TBL_ENTRY(0x239), TBL_ENTRY(0x23a), TBL_ENTRY(0x23b),
+ TBL_ENTRY(0x23c), TBL_ENTRY(0x23d), TBL_ENTRY(0x23e), TBL_ENTRY(0x23f),
+ TBL_ENTRY(0x240), TBL_ENTRY(0x241), TBL_ENTRY(0x242), TBL_ENTRY(0x243),
+ TBL_ENTRY(0x244), TBL_ENTRY(0x245), TBL_ENTRY(0x246), TBL_ENTRY(0x247),
+ TBL_ENTRY(0x248), TBL_ENTRY(0x249), TBL_ENTRY(0x24a), TBL_ENTRY(0x24b),
+ TBL_ENTRY(0x24c), TBL_ENTRY(0x24d), TBL_ENTRY(0x24e), TBL_ENTRY(0x24f),
+ TBL_ENTRY(0x250), TBL_ENTRY(0x251), TBL_ENTRY(0x252), TBL_ENTRY(0x253),
+ TBL_ENTRY(0x254), TBL_ENTRY(0x255), TBL_ENTRY(0x256), TBL_ENTRY(0x257),
+ TBL_ENTRY(0x258), TBL_ENTRY(0x259), TBL_ENTRY(0x25a), TBL_ENTRY(0x25b),
+ TBL_ENTRY(0x25c), TBL_ENTRY(0x25d), TBL_ENTRY(0x25e), TBL_ENTRY(0x25f),
+ TBL_ENTRY(0x260), TBL_ENTRY(0x261), TBL_ENTRY(0x262), TBL_ENTRY(0x263),
+ TBL_ENTRY(0x264), TBL_ENTRY(0x265), TBL_ENTRY(0x266), TBL_ENTRY(0x267),
+ TBL_ENTRY(0x268), TBL_ENTRY(0x269), TBL_ENTRY(0x26a), TBL_ENTRY(0x26b),
+ TBL_ENTRY(0x26c), TBL_ENTRY(0x26d), TBL_ENTRY(0x26e), TBL_ENTRY(0x26f),
+ TBL_ENTRY(0x270), TBL_ENTRY(0x271), TBL_ENTRY(0x272), TBL_ENTRY(0x273),
+ TBL_ENTRY(0x274), TBL_ENTRY(0x275), TBL_ENTRY(0x276), TBL_ENTRY(0x277),
+ TBL_ENTRY(0x278), TBL_ENTRY(0x279), TBL_ENTRY(0x27a), TBL_ENTRY(0x27b),
+ TBL_ENTRY(0x27c), TBL_ENTRY(0x27d), TBL_ENTRY(0x27e), TBL_ENTRY(0x27f),
+ TBL_ENTRY(0x280), TBL_ENTRY(0x281), TBL_ENTRY(0x282), TBL_ENTRY(0x283),
+ TBL_ENTRY(0x284), TBL_ENTRY(0x285), TBL_ENTRY(0x286), TBL_ENTRY(0x287),
+ TBL_ENTRY(0x288), TBL_ENTRY(0x289), TBL_ENTRY(0x28a), TBL_ENTRY(0x28b),
+ TBL_ENTRY(0x28c), TBL_ENTRY(0x28d), TBL_ENTRY(0x28e), TBL_ENTRY(0x28f),
+ TBL_ENTRY(0x290), TBL_ENTRY(0x291), TBL_ENTRY(0x292), TBL_ENTRY(0x293),
+ TBL_ENTRY(0x294), TBL_ENTRY(0x295), TBL_ENTRY(0x296), TBL_ENTRY(0x297),
+ TBL_ENTRY(0x298), TBL_ENTRY(0x299), TBL_ENTRY(0x29a), TBL_ENTRY(0x29b),
+ TBL_ENTRY(0x29c), TBL_ENTRY(0x29d), TBL_ENTRY(0x29e), TBL_ENTRY(0x29f),
+ TBL_ENTRY(0x2a0), TBL_ENTRY(0x2a1), TBL_ENTRY(0x2a2), TBL_ENTRY(0x2a3),
+ TBL_ENTRY(0x2a4), TBL_ENTRY(0x2a5), TBL_ENTRY(0x2a6), TBL_ENTRY(0x2a7),
+ TBL_ENTRY(0x2a8), TBL_ENTRY(0x2a9), TBL_ENTRY(0x2aa), TBL_ENTRY(0x2ab),
+ TBL_ENTRY(0x2ac), TBL_ENTRY(0x2ad), TBL_ENTRY(0x2ae), TBL_ENTRY(0x2af),
+ TBL_ENTRY(0x2b0), TBL_ENTRY(0x2b1), TBL_ENTRY(0x2b2), TBL_ENTRY(0x2b3),
+ TBL_ENTRY(0x2b4), TBL_ENTRY(0x2b5), TBL_ENTRY(0x2b6), TBL_ENTRY(0x2b7),
+ TBL_ENTRY(0x2b8), TBL_ENTRY(0x2b9), TBL_ENTRY(0x2ba), TBL_ENTRY(0x2bb),
+ TBL_ENTRY(0x2bc), TBL_ENTRY(0x2bd), TBL_ENTRY(0x2be), TBL_ENTRY(0x2bf),
+ TBL_ENTRY(0x2c0), TBL_ENTRY(0x2c1), TBL_ENTRY(0x2c2), TBL_ENTRY(0x2c3),
+ TBL_ENTRY(0x2c4), TBL_ENTRY(0x2c5), TBL_ENTRY(0x2c6), TBL_ENTRY(0x2c7),
+ TBL_ENTRY(0x2c8), TBL_ENTRY(0x2c9), TBL_ENTRY(0x2ca), TBL_ENTRY(0x2cb),
+ TBL_ENTRY(0x2cc), TBL_ENTRY(0x2cd), TBL_ENTRY(0x2ce), TBL_ENTRY(0x2cf),
+ TBL_ENTRY(0x2d0), TBL_ENTRY(0x2d1), TBL_ENTRY(0x2d2), TBL_ENTRY(0x2d3),
+ TBL_ENTRY(0x2d4), TBL_ENTRY(0x2d5), TBL_ENTRY(0x2d6), TBL_ENTRY(0x2d7),
+ TBL_ENTRY(0x2d8), TBL_ENTRY(0x2d9), TBL_ENTRY(0x2da), TBL_ENTRY(0x2db),
+ TBL_ENTRY(0x2dc), TBL_ENTRY(0x2dd), TBL_ENTRY(0x2de), TBL_ENTRY(0x2df),
+ TBL_ENTRY(0x2e0), TBL_ENTRY(0x2e1), TBL_ENTRY(0x2e2), TBL_ENTRY(0x2e3),
+ TBL_ENTRY(0x2e4), TBL_ENTRY(0x2e5), TBL_ENTRY(0x2e6), TBL_ENTRY(0x2e7),
+ TBL_ENTRY(0x2e8), TBL_ENTRY(0x2e9), TBL_ENTRY(0x2ea), TBL_ENTRY(0x2eb),
+ TBL_ENTRY(0x2ec), TBL_ENTRY(0x2ed), TBL_ENTRY(0x2ee), TBL_ENTRY(0x2ef),
+ TBL_ENTRY(0x2f0), TBL_ENTRY(0x2f1), TBL_ENTRY(0x2f2), TBL_ENTRY(0x2f3),
+ TBL_ENTRY(0x2f4), TBL_ENTRY(0x2f5), TBL_ENTRY(0x2f6), TBL_ENTRY(0x2f7),
+ TBL_ENTRY(0x2f8), TBL_ENTRY(0x2f9), TBL_ENTRY(0x2fa), TBL_ENTRY(0x2fb),
+ TBL_ENTRY(0x2fc), TBL_ENTRY(0x2fd), TBL_ENTRY(0x2fe), TBL_ENTRY(0x2ff),
+ TBL_ENTRY(0x300), TBL_ENTRY(0x301), TBL_ENTRY(0x302), TBL_ENTRY(0x303),
+ TBL_ENTRY(0x304), TBL_ENTRY(0x305), TBL_ENTRY(0x306), TBL_ENTRY(0x307),
+ TBL_ENTRY(0x308), TBL_ENTRY(0x309), TBL_ENTRY(0x30a), TBL_ENTRY(0x30b),
+ TBL_ENTRY(0x30c), TBL_ENTRY(0x30d), TBL_ENTRY(0x30e), TBL_ENTRY(0x30f),
+ TBL_ENTRY(0x310), TBL_ENTRY(0x311), TBL_ENTRY(0x312), TBL_ENTRY(0x313),
+ TBL_ENTRY(0x314), TBL_ENTRY(0x315), TBL_ENTRY(0x316), TBL_ENTRY(0x317),
+ TBL_ENTRY(0x318), TBL_ENTRY(0x319), TBL_ENTRY(0x31a), TBL_ENTRY(0x31b),
+ TBL_ENTRY(0x31c), TBL_ENTRY(0x31d), TBL_ENTRY(0x31e), TBL_ENTRY(0x31f),
+ TBL_ENTRY(0x320), TBL_ENTRY(0x321), TBL_ENTRY(0x322), TBL_ENTRY(0x323),
+ TBL_ENTRY(0x324), TBL_ENTRY(0x325), TBL_ENTRY(0x326), TBL_ENTRY(0x327),
+ TBL_ENTRY(0x328), TBL_ENTRY(0x329), TBL_ENTRY(0x32a), TBL_ENTRY(0x32b),
+ TBL_ENTRY(0x32c), TBL_ENTRY(0x32d), TBL_ENTRY(0x32e), TBL_ENTRY(0x32f),
+ TBL_ENTRY(0x330), TBL_ENTRY(0x331), TBL_ENTRY(0x332), TBL_ENTRY(0x333),
+ TBL_ENTRY(0x334), TBL_ENTRY(0x335), TBL_ENTRY(0x336), TBL_ENTRY(0x337),
+ TBL_ENTRY(0x338), TBL_ENTRY(0x339), TBL_ENTRY(0x33a), TBL_ENTRY(0x33b),
+ TBL_ENTRY(0x33c), TBL_ENTRY(0x33d), TBL_ENTRY(0x33e), TBL_ENTRY(0x33f),
+ TBL_ENTRY(0x340), TBL_ENTRY(0x341), TBL_ENTRY(0x342), TBL_ENTRY(0x343),
+ TBL_ENTRY(0x344), TBL_ENTRY(0x345), TBL_ENTRY(0x346), TBL_ENTRY(0x347),
+ TBL_ENTRY(0x348), TBL_ENTRY(0x349), TBL_ENTRY(0x34a), TBL_ENTRY(0x34b),
+ TBL_ENTRY(0x34c), TBL_ENTRY(0x34d), TBL_ENTRY(0x34e), TBL_ENTRY(0x34f),
+ TBL_ENTRY(0x350), TBL_ENTRY(0x351), TBL_ENTRY(0x352), TBL_ENTRY(0x353),
+ TBL_ENTRY(0x354), TBL_ENTRY(0x355), TBL_ENTRY(0x356), TBL_ENTRY(0x357),
+ TBL_ENTRY(0x358), TBL_ENTRY(0x359), TBL_ENTRY(0x35a), TBL_ENTRY(0x35b),
+ TBL_ENTRY(0x35c), TBL_ENTRY(0x35d), TBL_ENTRY(0x35e), TBL_ENTRY(0x35f),
+ TBL_ENTRY(0x360), TBL_ENTRY(0x361), TBL_ENTRY(0x362), TBL_ENTRY(0x363),
+ TBL_ENTRY(0x364), TBL_ENTRY(0x365), TBL_ENTRY(0x366), TBL_ENTRY(0x367),
+ TBL_ENTRY(0x368), TBL_ENTRY(0x369), TBL_ENTRY(0x36a), TBL_ENTRY(0x36b),
+ TBL_ENTRY(0x36c), TBL_ENTRY(0x36d), TBL_ENTRY(0x36e), TBL_ENTRY(0x36f),
+ TBL_ENTRY(0x370), TBL_ENTRY(0x371), TBL_ENTRY(0x372), TBL_ENTRY(0x373),
+ TBL_ENTRY(0x374), TBL_ENTRY(0x375), TBL_ENTRY(0x376), TBL_ENTRY(0x377),
+ TBL_ENTRY(0x378), TBL_ENTRY(0x379), TBL_ENTRY(0x37a), TBL_ENTRY(0x37b),
+ TBL_ENTRY(0x37c), TBL_ENTRY(0x37d), TBL_ENTRY(0x37e), TBL_ENTRY(0x37f),
+ TBL_ENTRY(0x380), TBL_ENTRY(0x381), TBL_ENTRY(0x382), TBL_ENTRY(0x383),
+ TBL_ENTRY(0x384), TBL_ENTRY(0x385), TBL_ENTRY(0x386), TBL_ENTRY(0x387),
+ TBL_ENTRY(0x388), TBL_ENTRY(0x389), TBL_ENTRY(0x38a), TBL_ENTRY(0x38b),
+ TBL_ENTRY(0x38c), TBL_ENTRY(0x38d), TBL_ENTRY(0x38e), TBL_ENTRY(0x38f),
+ TBL_ENTRY(0x390), TBL_ENTRY(0x391), TBL_ENTRY(0x392), TBL_ENTRY(0x393),
+ TBL_ENTRY(0x394), TBL_ENTRY(0x395), TBL_ENTRY(0x396), TBL_ENTRY(0x397),
+ TBL_ENTRY(0x398), TBL_ENTRY(0x399), TBL_ENTRY(0x39a), TBL_ENTRY(0x39b),
+ TBL_ENTRY(0x39c), TBL_ENTRY(0x39d), TBL_ENTRY(0x39e), TBL_ENTRY(0x39f),
+ TBL_ENTRY(0x3a0), TBL_ENTRY(0x3a1), TBL_ENTRY(0x3a2), TBL_ENTRY(0x3a3),
+ TBL_ENTRY(0x3a4), TBL_ENTRY(0x3a5), TBL_ENTRY(0x3a6), TBL_ENTRY(0x3a7),
+ TBL_ENTRY(0x3a8), TBL_ENTRY(0x3a9), TBL_ENTRY(0x3aa), TBL_ENTRY(0x3ab),
+ TBL_ENTRY(0x3ac), TBL_ENTRY(0x3ad), TBL_ENTRY(0x3ae), TBL_ENTRY(0x3af),
+ TBL_ENTRY(0x3b0), TBL_ENTRY(0x3b1), TBL_ENTRY(0x3b2), TBL_ENTRY(0x3b3),
+ TBL_ENTRY(0x3b4), TBL_ENTRY(0x3b5), TBL_ENTRY(0x3b6), TBL_ENTRY(0x3b7),
+ TBL_ENTRY(0x3b8), TBL_ENTRY(0x3b9), TBL_ENTRY(0x3ba), TBL_ENTRY(0x3bb),
+ TBL_ENTRY(0x3bc), TBL_ENTRY(0x3bd), TBL_ENTRY(0x3be), TBL_ENTRY(0x3bf),
+ TBL_ENTRY(0x3c0), TBL_ENTRY(0x3c1), TBL_ENTRY(0x3c2), TBL_ENTRY(0x3c3),
+ TBL_ENTRY(0x3c4), TBL_ENTRY(0x3c5), TBL_ENTRY(0x3c6), TBL_ENTRY(0x3c7),
+ TBL_ENTRY(0x3c8), TBL_ENTRY(0x3c9), TBL_ENTRY(0x3ca), TBL_ENTRY(0x3cb),
+ TBL_ENTRY(0x3cc), TBL_ENTRY(0x3cd), TBL_ENTRY(0x3ce), TBL_ENTRY(0x3cf),
+ TBL_ENTRY(0x3d0), TBL_ENTRY(0x3d1), TBL_ENTRY(0x3d2), TBL_ENTRY(0x3d3),
+ TBL_ENTRY(0x3d4), TBL_ENTRY(0x3d5), TBL_ENTRY(0x3d6), TBL_ENTRY(0x3d7),
+ TBL_ENTRY(0x3d8), TBL_ENTRY(0x3d9), TBL_ENTRY(0x3da), TBL_ENTRY(0x3db),
+ TBL_ENTRY(0x3dc), TBL_ENTRY(0x3dd), TBL_ENTRY(0x3de), TBL_ENTRY(0x3df),
+ TBL_ENTRY(0x3e0), TBL_ENTRY(0x3e1), TBL_ENTRY(0x3e2), TBL_ENTRY(0x3e3),
+ TBL_ENTRY(0x3e4), TBL_ENTRY(0x3e5), TBL_ENTRY(0x3e6), TBL_ENTRY(0x3e7),
+ TBL_ENTRY(0x3e8), TBL_ENTRY(0x3e9), TBL_ENTRY(0x3ea), TBL_ENTRY(0x3eb),
+ TBL_ENTRY(0x3ec), TBL_ENTRY(0x3ed), TBL_ENTRY(0x3ee), TBL_ENTRY(0x3ef),
+ TBL_ENTRY(0x3f0), TBL_ENTRY(0x3f1), TBL_ENTRY(0x3f2), TBL_ENTRY(0x3f3),
+ TBL_ENTRY(0x3f4), TBL_ENTRY(0x3f5), TBL_ENTRY(0x3f6), TBL_ENTRY(0x3f7),
+ TBL_ENTRY(0x3f8), TBL_ENTRY(0x3f9), TBL_ENTRY(0x3fa), TBL_ENTRY(0x3fb),
+ TBL_ENTRY(0x3fc), TBL_ENTRY(0x3fd), TBL_ENTRY(0x3fe), TBL_ENTRY(0x3ff),
+ TBL_ENTRY(0x400), TBL_ENTRY(0x401), TBL_ENTRY(0x402), TBL_ENTRY(0x403),
+ TBL_ENTRY(0x404), TBL_ENTRY(0x405), TBL_ENTRY(0x406), TBL_ENTRY(0x407),
+ TBL_ENTRY(0x408), TBL_ENTRY(0x409), TBL_ENTRY(0x40a), TBL_ENTRY(0x40b),
+ TBL_ENTRY(0x40c), TBL_ENTRY(0x40d), TBL_ENTRY(0x40e), TBL_ENTRY(0x40f),
+ TBL_ENTRY(0x410), TBL_ENTRY(0x411), TBL_ENTRY(0x412), TBL_ENTRY(0x413),
+ TBL_ENTRY(0x414), TBL_ENTRY(0x415), TBL_ENTRY(0x416), TBL_ENTRY(0x417),
+ TBL_ENTRY(0x418), TBL_ENTRY(0x419), TBL_ENTRY(0x41a), TBL_ENTRY(0x41b),
+ TBL_ENTRY(0x41c), TBL_ENTRY(0x41d), TBL_ENTRY(0x41e), TBL_ENTRY(0x41f),
+ TBL_ENTRY(0x420), TBL_ENTRY(0x421), TBL_ENTRY(0x422), TBL_ENTRY(0x423),
+ TBL_ENTRY(0x424), TBL_ENTRY(0x425), TBL_ENTRY(0x426), TBL_ENTRY(0x427),
+ TBL_ENTRY(0x428), TBL_ENTRY(0x429), TBL_ENTRY(0x42a), TBL_ENTRY(0x42b),
+ TBL_ENTRY(0x42c), TBL_ENTRY(0x42d), TBL_ENTRY(0x42e), TBL_ENTRY(0x42f),
+ TBL_ENTRY(0x430), TBL_ENTRY(0x431), TBL_ENTRY(0x432), TBL_ENTRY(0x433),
+ TBL_ENTRY(0x434), TBL_ENTRY(0x435), TBL_ENTRY(0x436), TBL_ENTRY(0x437),
+ TBL_ENTRY(0x438), TBL_ENTRY(0x439), TBL_ENTRY(0x43a), TBL_ENTRY(0x43b),
+ TBL_ENTRY(0x43c), TBL_ENTRY(0x43d), TBL_ENTRY(0x43e), TBL_ENTRY(0x43f),
+ TBL_ENTRY(0x440), TBL_ENTRY(0x441), TBL_ENTRY(0x442), TBL_ENTRY(0x443),
+ TBL_ENTRY(0x444), TBL_ENTRY(0x445), TBL_ENTRY(0x446), TBL_ENTRY(0x447),
+ TBL_ENTRY(0x448), TBL_ENTRY(0x449), TBL_ENTRY(0x44a), TBL_ENTRY(0x44b),
+ TBL_ENTRY(0x44c), TBL_ENTRY(0x44d), TBL_ENTRY(0x44e), TBL_ENTRY(0x44f),
+ TBL_ENTRY(0x450), TBL_ENTRY(0x451), TBL_ENTRY(0x452), TBL_ENTRY(0x453),
+ TBL_ENTRY(0x454), TBL_ENTRY(0x455), TBL_ENTRY(0x456), TBL_ENTRY(0x457),
+ TBL_ENTRY(0x458), TBL_ENTRY(0x459), TBL_ENTRY(0x45a), TBL_ENTRY(0x45b),
+ TBL_ENTRY(0x45c), TBL_ENTRY(0x45d), TBL_ENTRY(0x45e), TBL_ENTRY(0x45f),
+ TBL_ENTRY(0x460), TBL_ENTRY(0x461), TBL_ENTRY(0x462), TBL_ENTRY(0x463),
+ TBL_ENTRY(0x464), TBL_ENTRY(0x465), TBL_ENTRY(0x466), TBL_ENTRY(0x467),
+ TBL_ENTRY(0x468), TBL_ENTRY(0x469), TBL_ENTRY(0x46a), TBL_ENTRY(0x46b),
+ TBL_ENTRY(0x46c), TBL_ENTRY(0x46d), TBL_ENTRY(0x46e), TBL_ENTRY(0x46f),
+ TBL_ENTRY(0x470), TBL_ENTRY(0x471), TBL_ENTRY(0x472), TBL_ENTRY(0x473),
+ TBL_ENTRY(0x474), TBL_ENTRY(0x475), TBL_ENTRY(0x476), TBL_ENTRY(0x477),
+ TBL_ENTRY(0x478), TBL_ENTRY(0x479), TBL_ENTRY(0x47a), TBL_ENTRY(0x47b),
+ TBL_ENTRY(0x47c), TBL_ENTRY(0x47d), TBL_ENTRY(0x47e), TBL_ENTRY(0x47f),
+ TBL_ENTRY(0x480), TBL_ENTRY(0x481), TBL_ENTRY(0x482), TBL_ENTRY(0x483),
+ TBL_ENTRY(0x484), TBL_ENTRY(0x485), TBL_ENTRY(0x486), TBL_ENTRY(0x487),
+ TBL_ENTRY(0x488), TBL_ENTRY(0x489), TBL_ENTRY(0x48a), TBL_ENTRY(0x48b),
+ TBL_ENTRY(0x48c), TBL_ENTRY(0x48d), TBL_ENTRY(0x48e), TBL_ENTRY(0x48f),
+ TBL_ENTRY(0x490), TBL_ENTRY(0x491), TBL_ENTRY(0x492), TBL_ENTRY(0x493),
+ TBL_ENTRY(0x494), TBL_ENTRY(0x495), TBL_ENTRY(0x496), TBL_ENTRY(0x497),
+ TBL_ENTRY(0x498), TBL_ENTRY(0x499), TBL_ENTRY(0x49a), TBL_ENTRY(0x49b),
+ TBL_ENTRY(0x49c), TBL_ENTRY(0x49d), TBL_ENTRY(0x49e), TBL_ENTRY(0x49f),
+ TBL_ENTRY(0x4a0), TBL_ENTRY(0x4a1), TBL_ENTRY(0x4a2), TBL_ENTRY(0x4a3),
+ TBL_ENTRY(0x4a4), TBL_ENTRY(0x4a5), TBL_ENTRY(0x4a6), TBL_ENTRY(0x4a7),
+ TBL_ENTRY(0x4a8), TBL_ENTRY(0x4a9), TBL_ENTRY(0x4aa), TBL_ENTRY(0x4ab),
+ TBL_ENTRY(0x4ac), TBL_ENTRY(0x4ad), TBL_ENTRY(0x4ae), TBL_ENTRY(0x4af),
+ TBL_ENTRY(0x4b0), TBL_ENTRY(0x4b1), TBL_ENTRY(0x4b2), TBL_ENTRY(0x4b3),
+ TBL_ENTRY(0x4b4), TBL_ENTRY(0x4b5), TBL_ENTRY(0x4b6), TBL_ENTRY(0x4b7),
+ TBL_ENTRY(0x4b8), TBL_ENTRY(0x4b9), TBL_ENTRY(0x4ba), TBL_ENTRY(0x4bb),
+ TBL_ENTRY(0x4bc), TBL_ENTRY(0x4bd), TBL_ENTRY(0x4be), TBL_ENTRY(0x4bf),
+ TBL_ENTRY(0x4c0), TBL_ENTRY(0x4c1), TBL_ENTRY(0x4c2), TBL_ENTRY(0x4c3),
+ TBL_ENTRY(0x4c4), TBL_ENTRY(0x4c5), TBL_ENTRY(0x4c6), TBL_ENTRY(0x4c7),
+ TBL_ENTRY(0x4c8), TBL_ENTRY(0x4c9), TBL_ENTRY(0x4ca), TBL_ENTRY(0x4cb),
+ TBL_ENTRY(0x4cc), TBL_ENTRY(0x4cd), TBL_ENTRY(0x4ce), TBL_ENTRY(0x4cf),
+ TBL_ENTRY(0x4d0), TBL_ENTRY(0x4d1), TBL_ENTRY(0x4d2), TBL_ENTRY(0x4d3),
+ TBL_ENTRY(0x4d4), TBL_ENTRY(0x4d5), TBL_ENTRY(0x4d6), TBL_ENTRY(0x4d7),
+ TBL_ENTRY(0x4d8), TBL_ENTRY(0x4d9), TBL_ENTRY(0x4da), TBL_ENTRY(0x4db),
+ TBL_ENTRY(0x4dc), TBL_ENTRY(0x4dd), TBL_ENTRY(0x4de), TBL_ENTRY(0x4df),
+ TBL_ENTRY(0x4e0), TBL_ENTRY(0x4e1), TBL_ENTRY(0x4e2), TBL_ENTRY(0x4e3),
+ TBL_ENTRY(0x4e4), TBL_ENTRY(0x4e5), TBL_ENTRY(0x4e6), TBL_ENTRY(0x4e7),
+ TBL_ENTRY(0x4e8), TBL_ENTRY(0x4e9), TBL_ENTRY(0x4ea), TBL_ENTRY(0x4eb),
+ TBL_ENTRY(0x4ec), TBL_ENTRY(0x4ed), TBL_ENTRY(0x4ee), TBL_ENTRY(0x4ef),
+ TBL_ENTRY(0x4f0), TBL_ENTRY(0x4f1), TBL_ENTRY(0x4f2), TBL_ENTRY(0x4f3),
+ TBL_ENTRY(0x4f4), TBL_ENTRY(0x4f5), TBL_ENTRY(0x4f6), TBL_ENTRY(0x4f7),
+ TBL_ENTRY(0x4f8), TBL_ENTRY(0x4f9), TBL_ENTRY(0x4fa), TBL_ENTRY(0x4fb),
+ TBL_ENTRY(0x4fc), TBL_ENTRY(0x4fd), TBL_ENTRY(0x4fe), TBL_ENTRY(0x4ff),
+ TBL_ENTRY(0x500), TBL_ENTRY(0x501), TBL_ENTRY(0x502), TBL_ENTRY(0x503),
+ TBL_ENTRY(0x504), TBL_ENTRY(0x505), TBL_ENTRY(0x506), TBL_ENTRY(0x507),
+ TBL_ENTRY(0x508), TBL_ENTRY(0x509), TBL_ENTRY(0x50a), TBL_ENTRY(0x50b),
+ TBL_ENTRY(0x50c), TBL_ENTRY(0x50d), TBL_ENTRY(0x50e), TBL_ENTRY(0x50f),
+ TBL_ENTRY(0x510), TBL_ENTRY(0x511), TBL_ENTRY(0x512), TBL_ENTRY(0x513),
+ TBL_ENTRY(0x514), TBL_ENTRY(0x515), TBL_ENTRY(0x516), TBL_ENTRY(0x517),
+ TBL_ENTRY(0x518), TBL_ENTRY(0x519), TBL_ENTRY(0x51a), TBL_ENTRY(0x51b),
+ TBL_ENTRY(0x51c), TBL_ENTRY(0x51d), TBL_ENTRY(0x51e), TBL_ENTRY(0x51f),
+ TBL_ENTRY(0x520), TBL_ENTRY(0x521), TBL_ENTRY(0x522), TBL_ENTRY(0x523),
+ TBL_ENTRY(0x524), TBL_ENTRY(0x525), TBL_ENTRY(0x526), TBL_ENTRY(0x527),
+ TBL_ENTRY(0x528), TBL_ENTRY(0x529), TBL_ENTRY(0x52a), TBL_ENTRY(0x52b),
+ TBL_ENTRY(0x52c), TBL_ENTRY(0x52d), TBL_ENTRY(0x52e), TBL_ENTRY(0x52f),
+ TBL_ENTRY(0x530), TBL_ENTRY(0x531), TBL_ENTRY(0x532), TBL_ENTRY(0x533),
+ TBL_ENTRY(0x534), TBL_ENTRY(0x535), TBL_ENTRY(0x536), TBL_ENTRY(0x537),
+ TBL_ENTRY(0x538), TBL_ENTRY(0x539), TBL_ENTRY(0x53a), TBL_ENTRY(0x53b),
+ TBL_ENTRY(0x53c), TBL_ENTRY(0x53d), TBL_ENTRY(0x53e), TBL_ENTRY(0x53f),
+ TBL_ENTRY(0x540), TBL_ENTRY(0x541), TBL_ENTRY(0x542), TBL_ENTRY(0x543),
+ TBL_ENTRY(0x544), TBL_ENTRY(0x545), TBL_ENTRY(0x546), TBL_ENTRY(0x547),
+ TBL_ENTRY(0x548), TBL_ENTRY(0x549), TBL_ENTRY(0x54a), TBL_ENTRY(0x54b),
+ TBL_ENTRY(0x54c), TBL_ENTRY(0x54d), TBL_ENTRY(0x54e), TBL_ENTRY(0x54f),
+ TBL_ENTRY(0x550), TBL_ENTRY(0x551), TBL_ENTRY(0x552), TBL_ENTRY(0x553),
+ TBL_ENTRY(0x554), TBL_ENTRY(0x555), TBL_ENTRY(0x556), TBL_ENTRY(0x557),
+ TBL_ENTRY(0x558), TBL_ENTRY(0x559), TBL_ENTRY(0x55a), TBL_ENTRY(0x55b),
+ TBL_ENTRY(0x55c), TBL_ENTRY(0x55d), TBL_ENTRY(0x55e), TBL_ENTRY(0x55f),
+ TBL_ENTRY(0x560), TBL_ENTRY(0x561), TBL_ENTRY(0x562), TBL_ENTRY(0x563),
+ TBL_ENTRY(0x564), TBL_ENTRY(0x565), TBL_ENTRY(0x566), TBL_ENTRY(0x567),
+ TBL_ENTRY(0x568), TBL_ENTRY(0x569), TBL_ENTRY(0x56a), TBL_ENTRY(0x56b),
+ TBL_ENTRY(0x56c), TBL_ENTRY(0x56d), TBL_ENTRY(0x56e), TBL_ENTRY(0x56f),
+ TBL_ENTRY(0x570), TBL_ENTRY(0x571), TBL_ENTRY(0x572), TBL_ENTRY(0x573),
+ TBL_ENTRY(0x574), TBL_ENTRY(0x575), TBL_ENTRY(0x576), TBL_ENTRY(0x577),
+ TBL_ENTRY(0x578), TBL_ENTRY(0x579), TBL_ENTRY(0x57a), TBL_ENTRY(0x57b),
+ TBL_ENTRY(0x57c), TBL_ENTRY(0x57d), TBL_ENTRY(0x57e), TBL_ENTRY(0x57f),
+ TBL_ENTRY(0x580), TBL_ENTRY(0x581), TBL_ENTRY(0x582), TBL_ENTRY(0x583),
+ TBL_ENTRY(0x584), TBL_ENTRY(0x585), TBL_ENTRY(0x586), TBL_ENTRY(0x587),
+ TBL_ENTRY(0x588), TBL_ENTRY(0x589), TBL_ENTRY(0x58a), TBL_ENTRY(0x58b),
+ TBL_ENTRY(0x58c), TBL_ENTRY(0x58d), TBL_ENTRY(0x58e), TBL_ENTRY(0x58f),
+ TBL_ENTRY(0x590), TBL_ENTRY(0x591), TBL_ENTRY(0x592), TBL_ENTRY(0x593),
+ TBL_ENTRY(0x594), TBL_ENTRY(0x595), TBL_ENTRY(0x596), TBL_ENTRY(0x597),
+ TBL_ENTRY(0x598), TBL_ENTRY(0x599), TBL_ENTRY(0x59a), TBL_ENTRY(0x59b),
+ TBL_ENTRY(0x59c), TBL_ENTRY(0x59d), TBL_ENTRY(0x59e), TBL_ENTRY(0x59f),
+ TBL_ENTRY(0x5a0), TBL_ENTRY(0x5a1), TBL_ENTRY(0x5a2), TBL_ENTRY(0x5a3),
+ TBL_ENTRY(0x5a4), TBL_ENTRY(0x5a5), TBL_ENTRY(0x5a6), TBL_ENTRY(0x5a7),
+ TBL_ENTRY(0x5a8), TBL_ENTRY(0x5a9), TBL_ENTRY(0x5aa), TBL_ENTRY(0x5ab),
+ TBL_ENTRY(0x5ac), TBL_ENTRY(0x5ad), TBL_ENTRY(0x5ae), TBL_ENTRY(0x5af),
+ TBL_ENTRY(0x5b0), TBL_ENTRY(0x5b1), TBL_ENTRY(0x5b2), TBL_ENTRY(0x5b3),
+ TBL_ENTRY(0x5b4), TBL_ENTRY(0x5b5), TBL_ENTRY(0x5b6), TBL_ENTRY(0x5b7),
+ TBL_ENTRY(0x5b8), TBL_ENTRY(0x5b9), TBL_ENTRY(0x5ba), TBL_ENTRY(0x5bb),
+ TBL_ENTRY(0x5bc), TBL_ENTRY(0x5bd), TBL_ENTRY(0x5be), TBL_ENTRY(0x5bf),
+ TBL_ENTRY(0x5c0), TBL_ENTRY(0x5c1), TBL_ENTRY(0x5c2), TBL_ENTRY(0x5c3),
+ TBL_ENTRY(0x5c4), TBL_ENTRY(0x5c5), TBL_ENTRY(0x5c6), TBL_ENTRY(0x5c7),
+ TBL_ENTRY(0x5c8), TBL_ENTRY(0x5c9), TBL_ENTRY(0x5ca), TBL_ENTRY(0x5cb),
+ TBL_ENTRY(0x5cc), TBL_ENTRY(0x5cd), TBL_ENTRY(0x5ce), TBL_ENTRY(0x5cf),
+ TBL_ENTRY(0x5d0), TBL_ENTRY(0x5d1), TBL_ENTRY(0x5d2), TBL_ENTRY(0x5d3),
+ TBL_ENTRY(0x5d4), TBL_ENTRY(0x5d5), TBL_ENTRY(0x5d6), TBL_ENTRY(0x5d7),
+ TBL_ENTRY(0x5d8), TBL_ENTRY(0x5d9), TBL_ENTRY(0x5da), TBL_ENTRY(0x5db),
+ TBL_ENTRY(0x5dc), TBL_ENTRY(0x5dd), TBL_ENTRY(0x5de), TBL_ENTRY(0x5df),
+ TBL_ENTRY(0x5e0), TBL_ENTRY(0x5e1), TBL_ENTRY(0x5e2), TBL_ENTRY(0x5e3),
+ TBL_ENTRY(0x5e4), TBL_ENTRY(0x5e5), TBL_ENTRY(0x5e6), TBL_ENTRY(0x5e7),
+ TBL_ENTRY(0x5e8), TBL_ENTRY(0x5e9), TBL_ENTRY(0x5ea), TBL_ENTRY(0x5eb),
+ TBL_ENTRY(0x5ec), TBL_ENTRY(0x5ed), TBL_ENTRY(0x5ee), TBL_ENTRY(0x5ef),
+ TBL_ENTRY(0x5f0), TBL_ENTRY(0x5f1), TBL_ENTRY(0x5f2), TBL_ENTRY(0x5f3),
+ TBL_ENTRY(0x5f4), TBL_ENTRY(0x5f5), TBL_ENTRY(0x5f6), TBL_ENTRY(0x5f7),
+ TBL_ENTRY(0x5f8), TBL_ENTRY(0x5f9), TBL_ENTRY(0x5fa), TBL_ENTRY(0x5fb),
+ TBL_ENTRY(0x5fc), TBL_ENTRY(0x5fd), TBL_ENTRY(0x5fe), TBL_ENTRY(0x5ff),
+ TBL_ENTRY(0x600), TBL_ENTRY(0x601), TBL_ENTRY(0x602), TBL_ENTRY(0x603),
+ TBL_ENTRY(0x604), TBL_ENTRY(0x605), TBL_ENTRY(0x606), TBL_ENTRY(0x607),
+ TBL_ENTRY(0x608), TBL_ENTRY(0x609), TBL_ENTRY(0x60a), TBL_ENTRY(0x60b),
+ TBL_ENTRY(0x60c), TBL_ENTRY(0x60d), TBL_ENTRY(0x60e), TBL_ENTRY(0x60f),
+ TBL_ENTRY(0x610), TBL_ENTRY(0x611), TBL_ENTRY(0x612), TBL_ENTRY(0x613),
+ TBL_ENTRY(0x614), TBL_ENTRY(0x615), TBL_ENTRY(0x616), TBL_ENTRY(0x617),
+ TBL_ENTRY(0x618), TBL_ENTRY(0x619), TBL_ENTRY(0x61a), TBL_ENTRY(0x61b),
+ TBL_ENTRY(0x61c), TBL_ENTRY(0x61d), TBL_ENTRY(0x61e), TBL_ENTRY(0x61f),
+ TBL_ENTRY(0x620), TBL_ENTRY(0x621), TBL_ENTRY(0x622), TBL_ENTRY(0x623),
+ TBL_ENTRY(0x624), TBL_ENTRY(0x625), TBL_ENTRY(0x626), TBL_ENTRY(0x627),
+ TBL_ENTRY(0x628), TBL_ENTRY(0x629), TBL_ENTRY(0x62a), TBL_ENTRY(0x62b),
+ TBL_ENTRY(0x62c), TBL_ENTRY(0x62d), TBL_ENTRY(0x62e), TBL_ENTRY(0x62f),
+ TBL_ENTRY(0x630), TBL_ENTRY(0x631), TBL_ENTRY(0x632), TBL_ENTRY(0x633),
+ TBL_ENTRY(0x634), TBL_ENTRY(0x635), TBL_ENTRY(0x636), TBL_ENTRY(0x637),
+ TBL_ENTRY(0x638), TBL_ENTRY(0x639), TBL_ENTRY(0x63a), TBL_ENTRY(0x63b),
+ TBL_ENTRY(0x63c), TBL_ENTRY(0x63d), TBL_ENTRY(0x63e), TBL_ENTRY(0x63f),
+ TBL_ENTRY(0x640), TBL_ENTRY(0x641), TBL_ENTRY(0x642), TBL_ENTRY(0x643),
+ TBL_ENTRY(0x644), TBL_ENTRY(0x645), TBL_ENTRY(0x646), TBL_ENTRY(0x647),
+ TBL_ENTRY(0x648), TBL_ENTRY(0x649), TBL_ENTRY(0x64a), TBL_ENTRY(0x64b),
+ TBL_ENTRY(0x64c), TBL_ENTRY(0x64d), TBL_ENTRY(0x64e), TBL_ENTRY(0x64f),
+ TBL_ENTRY(0x650), TBL_ENTRY(0x651), TBL_ENTRY(0x652), TBL_ENTRY(0x653),
+ TBL_ENTRY(0x654), TBL_ENTRY(0x655), TBL_ENTRY(0x656), TBL_ENTRY(0x657),
+ TBL_ENTRY(0x658), TBL_ENTRY(0x659), TBL_ENTRY(0x65a), TBL_ENTRY(0x65b),
+ TBL_ENTRY(0x65c), TBL_ENTRY(0x65d), TBL_ENTRY(0x65e), TBL_ENTRY(0x65f),
+ TBL_ENTRY(0x660), TBL_ENTRY(0x661), TBL_ENTRY(0x662), TBL_ENTRY(0x663),
+ TBL_ENTRY(0x664), TBL_ENTRY(0x665), TBL_ENTRY(0x666), TBL_ENTRY(0x667),
+ TBL_ENTRY(0x668), TBL_ENTRY(0x669), TBL_ENTRY(0x66a), TBL_ENTRY(0x66b),
+ TBL_ENTRY(0x66c), TBL_ENTRY(0x66d), TBL_ENTRY(0x66e), TBL_ENTRY(0x66f),
+ TBL_ENTRY(0x670), TBL_ENTRY(0x671), TBL_ENTRY(0x672), TBL_ENTRY(0x673),
+ TBL_ENTRY(0x674), TBL_ENTRY(0x675), TBL_ENTRY(0x676), TBL_ENTRY(0x677),
+ TBL_ENTRY(0x678), TBL_ENTRY(0x679), TBL_ENTRY(0x67a), TBL_ENTRY(0x67b),
+ TBL_ENTRY(0x67c), TBL_ENTRY(0x67d), TBL_ENTRY(0x67e), TBL_ENTRY(0x67f),
+ TBL_ENTRY(0x680), TBL_ENTRY(0x681), TBL_ENTRY(0x682), TBL_ENTRY(0x683),
+ TBL_ENTRY(0x684), TBL_ENTRY(0x685), TBL_ENTRY(0x686), TBL_ENTRY(0x687),
+ TBL_ENTRY(0x688), TBL_ENTRY(0x689), TBL_ENTRY(0x68a), TBL_ENTRY(0x68b),
+ TBL_ENTRY(0x68c), TBL_ENTRY(0x68d), TBL_ENTRY(0x68e), TBL_ENTRY(0x68f),
+ TBL_ENTRY(0x690), TBL_ENTRY(0x691), TBL_ENTRY(0x692), TBL_ENTRY(0x693),
+ TBL_ENTRY(0x694), TBL_ENTRY(0x695), TBL_ENTRY(0x696), TBL_ENTRY(0x697),
+ TBL_ENTRY(0x698), TBL_ENTRY(0x699), TBL_ENTRY(0x69a), TBL_ENTRY(0x69b),
+ TBL_ENTRY(0x69c), TBL_ENTRY(0x69d), TBL_ENTRY(0x69e), TBL_ENTRY(0x69f),
+ TBL_ENTRY(0x6a0), TBL_ENTRY(0x6a1), TBL_ENTRY(0x6a2), TBL_ENTRY(0x6a3),
+ TBL_ENTRY(0x6a4), TBL_ENTRY(0x6a5), TBL_ENTRY(0x6a6), TBL_ENTRY(0x6a7),
+ TBL_ENTRY(0x6a8), TBL_ENTRY(0x6a9), TBL_ENTRY(0x6aa), TBL_ENTRY(0x6ab),
+ TBL_ENTRY(0x6ac), TBL_ENTRY(0x6ad), TBL_ENTRY(0x6ae), TBL_ENTRY(0x6af),
+ TBL_ENTRY(0x6b0), TBL_ENTRY(0x6b1), TBL_ENTRY(0x6b2), TBL_ENTRY(0x6b3),
+ TBL_ENTRY(0x6b4), TBL_ENTRY(0x6b5), TBL_ENTRY(0x6b6), TBL_ENTRY(0x6b7),
+ TBL_ENTRY(0x6b8), TBL_ENTRY(0x6b9), TBL_ENTRY(0x6ba), TBL_ENTRY(0x6bb),
+ TBL_ENTRY(0x6bc), TBL_ENTRY(0x6bd), TBL_ENTRY(0x6be), TBL_ENTRY(0x6bf),
+ TBL_ENTRY(0x6c0), TBL_ENTRY(0x6c1), TBL_ENTRY(0x6c2), TBL_ENTRY(0x6c3),
+ TBL_ENTRY(0x6c4), TBL_ENTRY(0x6c5), TBL_ENTRY(0x6c6), TBL_ENTRY(0x6c7),
+ TBL_ENTRY(0x6c8), TBL_ENTRY(0x6c9), TBL_ENTRY(0x6ca), TBL_ENTRY(0x6cb),
+ TBL_ENTRY(0x6cc), TBL_ENTRY(0x6cd), TBL_ENTRY(0x6ce), TBL_ENTRY(0x6cf),
+ TBL_ENTRY(0x6d0), TBL_ENTRY(0x6d1), TBL_ENTRY(0x6d2), TBL_ENTRY(0x6d3),
+ TBL_ENTRY(0x6d4), TBL_ENTRY(0x6d5), TBL_ENTRY(0x6d6), TBL_ENTRY(0x6d7),
+ TBL_ENTRY(0x6d8), TBL_ENTRY(0x6d9), TBL_ENTRY(0x6da), TBL_ENTRY(0x6db),
+ TBL_ENTRY(0x6dc), TBL_ENTRY(0x6dd), TBL_ENTRY(0x6de), TBL_ENTRY(0x6df),
+ TBL_ENTRY(0x6e0), TBL_ENTRY(0x6e1), TBL_ENTRY(0x6e2), TBL_ENTRY(0x6e3),
+ TBL_ENTRY(0x6e4), TBL_ENTRY(0x6e5), TBL_ENTRY(0x6e6), TBL_ENTRY(0x6e7),
+ TBL_ENTRY(0x6e8), TBL_ENTRY(0x6e9), TBL_ENTRY(0x6ea), TBL_ENTRY(0x6eb),
+ TBL_ENTRY(0x6ec), TBL_ENTRY(0x6ed), TBL_ENTRY(0x6ee), TBL_ENTRY(0x6ef),
+ TBL_ENTRY(0x6f0), TBL_ENTRY(0x6f1), TBL_ENTRY(0x6f2), TBL_ENTRY(0x6f3),
+ TBL_ENTRY(0x6f4), TBL_ENTRY(0x6f5), TBL_ENTRY(0x6f6), TBL_ENTRY(0x6f7),
+ TBL_ENTRY(0x6f8), TBL_ENTRY(0x6f9), TBL_ENTRY(0x6fa), TBL_ENTRY(0x6fb),
+ TBL_ENTRY(0x6fc), TBL_ENTRY(0x6fd), TBL_ENTRY(0x6fe), TBL_ENTRY(0x6ff),
+ TBL_ENTRY(0x700), TBL_ENTRY(0x701), TBL_ENTRY(0x702), TBL_ENTRY(0x703),
+ TBL_ENTRY(0x704), TBL_ENTRY(0x705), TBL_ENTRY(0x706), TBL_ENTRY(0x707),
+ TBL_ENTRY(0x708), TBL_ENTRY(0x709), TBL_ENTRY(0x70a), TBL_ENTRY(0x70b),
+ TBL_ENTRY(0x70c), TBL_ENTRY(0x70d), TBL_ENTRY(0x70e), TBL_ENTRY(0x70f),
+ TBL_ENTRY(0x710), TBL_ENTRY(0x711), TBL_ENTRY(0x712), TBL_ENTRY(0x713),
+ TBL_ENTRY(0x714), TBL_ENTRY(0x715), TBL_ENTRY(0x716), TBL_ENTRY(0x717),
+ TBL_ENTRY(0x718), TBL_ENTRY(0x719), TBL_ENTRY(0x71a), TBL_ENTRY(0x71b),
+ TBL_ENTRY(0x71c), TBL_ENTRY(0x71d), TBL_ENTRY(0x71e), TBL_ENTRY(0x71f),
+ TBL_ENTRY(0x720), TBL_ENTRY(0x721), TBL_ENTRY(0x722), TBL_ENTRY(0x723),
+ TBL_ENTRY(0x724), TBL_ENTRY(0x725), TBL_ENTRY(0x726), TBL_ENTRY(0x727),
+ TBL_ENTRY(0x728), TBL_ENTRY(0x729), TBL_ENTRY(0x72a), TBL_ENTRY(0x72b),
+ TBL_ENTRY(0x72c), TBL_ENTRY(0x72d), TBL_ENTRY(0x72e), TBL_ENTRY(0x72f),
+ TBL_ENTRY(0x730), TBL_ENTRY(0x731), TBL_ENTRY(0x732), TBL_ENTRY(0x733),
+ TBL_ENTRY(0x734), TBL_ENTRY(0x735), TBL_ENTRY(0x736), TBL_ENTRY(0x737),
+ TBL_ENTRY(0x738), TBL_ENTRY(0x739), TBL_ENTRY(0x73a), TBL_ENTRY(0x73b),
+ TBL_ENTRY(0x73c), TBL_ENTRY(0x73d), TBL_ENTRY(0x73e), TBL_ENTRY(0x73f),
+ TBL_ENTRY(0x740), TBL_ENTRY(0x741), TBL_ENTRY(0x742), TBL_ENTRY(0x743),
+ TBL_ENTRY(0x744), TBL_ENTRY(0x745), TBL_ENTRY(0x746), TBL_ENTRY(0x747),
+ TBL_ENTRY(0x748), TBL_ENTRY(0x749), TBL_ENTRY(0x74a), TBL_ENTRY(0x74b),
+ TBL_ENTRY(0x74c), TBL_ENTRY(0x74d), TBL_ENTRY(0x74e), TBL_ENTRY(0x74f),
+ TBL_ENTRY(0x750), TBL_ENTRY(0x751), TBL_ENTRY(0x752), TBL_ENTRY(0x753),
+ TBL_ENTRY(0x754), TBL_ENTRY(0x755), TBL_ENTRY(0x756), TBL_ENTRY(0x757),
+ TBL_ENTRY(0x758), TBL_ENTRY(0x759), TBL_ENTRY(0x75a), TBL_ENTRY(0x75b),
+ TBL_ENTRY(0x75c), TBL_ENTRY(0x75d), TBL_ENTRY(0x75e), TBL_ENTRY(0x75f),
+ TBL_ENTRY(0x760), TBL_ENTRY(0x761), TBL_ENTRY(0x762), TBL_ENTRY(0x763),
+ TBL_ENTRY(0x764), TBL_ENTRY(0x765), TBL_ENTRY(0x766), TBL_ENTRY(0x767),
+ TBL_ENTRY(0x768), TBL_ENTRY(0x769), TBL_ENTRY(0x76a), TBL_ENTRY(0x76b),
+ TBL_ENTRY(0x76c), TBL_ENTRY(0x76d), TBL_ENTRY(0x76e), TBL_ENTRY(0x76f),
+ TBL_ENTRY(0x770), TBL_ENTRY(0x771), TBL_ENTRY(0x772), TBL_ENTRY(0x773),
+ TBL_ENTRY(0x774), TBL_ENTRY(0x775), TBL_ENTRY(0x776), TBL_ENTRY(0x777),
+ TBL_ENTRY(0x778), TBL_ENTRY(0x779), TBL_ENTRY(0x77a), TBL_ENTRY(0x77b),
+ TBL_ENTRY(0x77c), TBL_ENTRY(0x77d), TBL_ENTRY(0x77e), TBL_ENTRY(0x77f),
+ TBL_ENTRY(0x780), TBL_ENTRY(0x781), TBL_ENTRY(0x782), TBL_ENTRY(0x783),
+ TBL_ENTRY(0x784), TBL_ENTRY(0x785), TBL_ENTRY(0x786), TBL_ENTRY(0x787),
+ TBL_ENTRY(0x788), TBL_ENTRY(0x789), TBL_ENTRY(0x78a), TBL_ENTRY(0x78b),
+ TBL_ENTRY(0x78c), TBL_ENTRY(0x78d), TBL_ENTRY(0x78e), TBL_ENTRY(0x78f),
+ TBL_ENTRY(0x790), TBL_ENTRY(0x791), TBL_ENTRY(0x792), TBL_ENTRY(0x793),
+ TBL_ENTRY(0x794), TBL_ENTRY(0x795), TBL_ENTRY(0x796), TBL_ENTRY(0x797),
+ TBL_ENTRY(0x798), TBL_ENTRY(0x799), TBL_ENTRY(0x79a), TBL_ENTRY(0x79b),
+ TBL_ENTRY(0x79c), TBL_ENTRY(0x79d), TBL_ENTRY(0x79e), TBL_ENTRY(0x79f),
+ TBL_ENTRY(0x7a0), TBL_ENTRY(0x7a1), TBL_ENTRY(0x7a2), TBL_ENTRY(0x7a3),
+ TBL_ENTRY(0x7a4), TBL_ENTRY(0x7a5), TBL_ENTRY(0x7a6), TBL_ENTRY(0x7a7),
+ TBL_ENTRY(0x7a8), TBL_ENTRY(0x7a9), TBL_ENTRY(0x7aa), TBL_ENTRY(0x7ab),
+ TBL_ENTRY(0x7ac), TBL_ENTRY(0x7ad), TBL_ENTRY(0x7ae), TBL_ENTRY(0x7af),
+ TBL_ENTRY(0x7b0), TBL_ENTRY(0x7b1), TBL_ENTRY(0x7b2), TBL_ENTRY(0x7b3),
+ TBL_ENTRY(0x7b4), TBL_ENTRY(0x7b5), TBL_ENTRY(0x7b6), TBL_ENTRY(0x7b7),
+ TBL_ENTRY(0x7b8), TBL_ENTRY(0x7b9), TBL_ENTRY(0x7ba), TBL_ENTRY(0x7bb),
+ TBL_ENTRY(0x7bc), TBL_ENTRY(0x7bd), TBL_ENTRY(0x7be), TBL_ENTRY(0x7bf),
+ TBL_ENTRY(0x7c0), TBL_ENTRY(0x7c1), TBL_ENTRY(0x7c2), TBL_ENTRY(0x7c3),
+ TBL_ENTRY(0x7c4), TBL_ENTRY(0x7c5), TBL_ENTRY(0x7c6), TBL_ENTRY(0x7c7),
+ TBL_ENTRY(0x7c8), TBL_ENTRY(0x7c9), TBL_ENTRY(0x7ca), TBL_ENTRY(0x7cb),
+ TBL_ENTRY(0x7cc), TBL_ENTRY(0x7cd), TBL_ENTRY(0x7ce), TBL_ENTRY(0x7cf),
+ TBL_ENTRY(0x7d0), TBL_ENTRY(0x7d1), TBL_ENTRY(0x7d2), TBL_ENTRY(0x7d3),
+ TBL_ENTRY(0x7d4), TBL_ENTRY(0x7d5), TBL_ENTRY(0x7d6), TBL_ENTRY(0x7d7),
+ TBL_ENTRY(0x7d8), TBL_ENTRY(0x7d9), TBL_ENTRY(0x7da), TBL_ENTRY(0x7db),
+ TBL_ENTRY(0x7dc), TBL_ENTRY(0x7dd), TBL_ENTRY(0x7de), TBL_ENTRY(0x7df),
+ TBL_ENTRY(0x7e0), TBL_ENTRY(0x7e1), TBL_ENTRY(0x7e2), TBL_ENTRY(0x7e3),
+ TBL_ENTRY(0x7e4), TBL_ENTRY(0x7e5), TBL_ENTRY(0x7e6), TBL_ENTRY(0x7e7),
+ TBL_ENTRY(0x7e8), TBL_ENTRY(0x7e9), TBL_ENTRY(0x7ea), TBL_ENTRY(0x7eb),
+ TBL_ENTRY(0x7ec), TBL_ENTRY(0x7ed), TBL_ENTRY(0x7ee), TBL_ENTRY(0x7ef),
+ TBL_ENTRY(0x7f0), TBL_ENTRY(0x7f1), TBL_ENTRY(0x7f2), TBL_ENTRY(0x7f3),
+ TBL_ENTRY(0x7f4), TBL_ENTRY(0x7f5), TBL_ENTRY(0x7f6), TBL_ENTRY(0x7f7),
+ TBL_ENTRY(0x7f8), TBL_ENTRY(0x7f9), TBL_ENTRY(0x7fa), TBL_ENTRY(0x7fb),
+ TBL_ENTRY(0x7fc), TBL_ENTRY(0x7fd), TBL_ENTRY(0x7fe), TBL_ENTRY(0x7ff),
+ TBL_ENTRY(0x800), TBL_ENTRY(0x801), TBL_ENTRY(0x802), TBL_ENTRY(0x803),
+ TBL_ENTRY(0x804), TBL_ENTRY(0x805), TBL_ENTRY(0x806), TBL_ENTRY(0x807),
+ TBL_ENTRY(0x808), TBL_ENTRY(0x809), TBL_ENTRY(0x80a), TBL_ENTRY(0x80b),
+ TBL_ENTRY(0x80c), TBL_ENTRY(0x80d), TBL_ENTRY(0x80e), TBL_ENTRY(0x80f),
+ TBL_ENTRY(0x810), TBL_ENTRY(0x811), TBL_ENTRY(0x812), TBL_ENTRY(0x813),
+ TBL_ENTRY(0x814), TBL_ENTRY(0x815), TBL_ENTRY(0x816), TBL_ENTRY(0x817),
+ TBL_ENTRY(0x818), TBL_ENTRY(0x819), TBL_ENTRY(0x81a), TBL_ENTRY(0x81b),
+ TBL_ENTRY(0x81c), TBL_ENTRY(0x81d), TBL_ENTRY(0x81e), TBL_ENTRY(0x81f),
+ TBL_ENTRY(0x820), TBL_ENTRY(0x821), TBL_ENTRY(0x822), TBL_ENTRY(0x823),
+ TBL_ENTRY(0x824), TBL_ENTRY(0x825), TBL_ENTRY(0x826), TBL_ENTRY(0x827),
+ TBL_ENTRY(0x828), TBL_ENTRY(0x829), TBL_ENTRY(0x82a), TBL_ENTRY(0x82b),
+ TBL_ENTRY(0x82c), TBL_ENTRY(0x82d), TBL_ENTRY(0x82e), TBL_ENTRY(0x82f),
+ TBL_ENTRY(0x830), TBL_ENTRY(0x831), TBL_ENTRY(0x832), TBL_ENTRY(0x833),
+ TBL_ENTRY(0x834), TBL_ENTRY(0x835), TBL_ENTRY(0x836), TBL_ENTRY(0x837),
+ TBL_ENTRY(0x838), TBL_ENTRY(0x839), TBL_ENTRY(0x83a), TBL_ENTRY(0x83b),
+ TBL_ENTRY(0x83c), TBL_ENTRY(0x83d), TBL_ENTRY(0x83e), TBL_ENTRY(0x83f),
+ TBL_ENTRY(0x840), TBL_ENTRY(0x841), TBL_ENTRY(0x842), TBL_ENTRY(0x843),
+ TBL_ENTRY(0x844), TBL_ENTRY(0x845), TBL_ENTRY(0x846), TBL_ENTRY(0x847),
+ TBL_ENTRY(0x848), TBL_ENTRY(0x849), TBL_ENTRY(0x84a), TBL_ENTRY(0x84b),
+ TBL_ENTRY(0x84c), TBL_ENTRY(0x84d), TBL_ENTRY(0x84e), TBL_ENTRY(0x84f),
+ TBL_ENTRY(0x850), TBL_ENTRY(0x851), TBL_ENTRY(0x852), TBL_ENTRY(0x853),
+ TBL_ENTRY(0x854), TBL_ENTRY(0x855), TBL_ENTRY(0x856), TBL_ENTRY(0x857),
+ TBL_ENTRY(0x858), TBL_ENTRY(0x859), TBL_ENTRY(0x85a), TBL_ENTRY(0x85b),
+ TBL_ENTRY(0x85c), TBL_ENTRY(0x85d), TBL_ENTRY(0x85e), TBL_ENTRY(0x85f),
+ TBL_ENTRY(0x860), TBL_ENTRY(0x861), TBL_ENTRY(0x862), TBL_ENTRY(0x863),
+ TBL_ENTRY(0x864), TBL_ENTRY(0x865), TBL_ENTRY(0x866), TBL_ENTRY(0x867),
+ TBL_ENTRY(0x868), TBL_ENTRY(0x869), TBL_ENTRY(0x86a), TBL_ENTRY(0x86b),
+ TBL_ENTRY(0x86c), TBL_ENTRY(0x86d), TBL_ENTRY(0x86e), TBL_ENTRY(0x86f),
+ TBL_ENTRY(0x870), TBL_ENTRY(0x871), TBL_ENTRY(0x872), TBL_ENTRY(0x873),
+ TBL_ENTRY(0x874), TBL_ENTRY(0x875), TBL_ENTRY(0x876), TBL_ENTRY(0x877),
+ TBL_ENTRY(0x878), TBL_ENTRY(0x879), TBL_ENTRY(0x87a), TBL_ENTRY(0x87b),
+ TBL_ENTRY(0x87c), TBL_ENTRY(0x87d), TBL_ENTRY(0x87e), TBL_ENTRY(0x87f),
+ TBL_ENTRY(0x880), TBL_ENTRY(0x881), TBL_ENTRY(0x882), TBL_ENTRY(0x883),
+ TBL_ENTRY(0x884), TBL_ENTRY(0x885), TBL_ENTRY(0x886), TBL_ENTRY(0x887),
+ TBL_ENTRY(0x888), TBL_ENTRY(0x889), TBL_ENTRY(0x88a), TBL_ENTRY(0x88b),
+ TBL_ENTRY(0x88c), TBL_ENTRY(0x88d), TBL_ENTRY(0x88e), TBL_ENTRY(0x88f),
+ TBL_ENTRY(0x890), TBL_ENTRY(0x891), TBL_ENTRY(0x892), TBL_ENTRY(0x893),
+ TBL_ENTRY(0x894), TBL_ENTRY(0x895), TBL_ENTRY(0x896), TBL_ENTRY(0x897),
+ TBL_ENTRY(0x898), TBL_ENTRY(0x899), TBL_ENTRY(0x89a), TBL_ENTRY(0x89b),
+ TBL_ENTRY(0x89c), TBL_ENTRY(0x89d), TBL_ENTRY(0x89e), TBL_ENTRY(0x89f),
+ TBL_ENTRY(0x8a0), TBL_ENTRY(0x8a1), TBL_ENTRY(0x8a2), TBL_ENTRY(0x8a3),
+ TBL_ENTRY(0x8a4), TBL_ENTRY(0x8a5), TBL_ENTRY(0x8a6), TBL_ENTRY(0x8a7),
+ TBL_ENTRY(0x8a8), TBL_ENTRY(0x8a9), TBL_ENTRY(0x8aa), TBL_ENTRY(0x8ab),
+ TBL_ENTRY(0x8ac), TBL_ENTRY(0x8ad), TBL_ENTRY(0x8ae), TBL_ENTRY(0x8af),
+ TBL_ENTRY(0x8b0), TBL_ENTRY(0x8b1), TBL_ENTRY(0x8b2), TBL_ENTRY(0x8b3),
+ TBL_ENTRY(0x8b4), TBL_ENTRY(0x8b5), TBL_ENTRY(0x8b6), TBL_ENTRY(0x8b7),
+ TBL_ENTRY(0x8b8), TBL_ENTRY(0x8b9), TBL_ENTRY(0x8ba), TBL_ENTRY(0x8bb),
+ TBL_ENTRY(0x8bc), TBL_ENTRY(0x8bd), TBL_ENTRY(0x8be), TBL_ENTRY(0x8bf),
+ TBL_ENTRY(0x8c0), TBL_ENTRY(0x8c1), TBL_ENTRY(0x8c2), TBL_ENTRY(0x8c3),
+ TBL_ENTRY(0x8c4), TBL_ENTRY(0x8c5), TBL_ENTRY(0x8c6), TBL_ENTRY(0x8c7),
+ TBL_ENTRY(0x8c8), TBL_ENTRY(0x8c9), TBL_ENTRY(0x8ca), TBL_ENTRY(0x8cb),
+ TBL_ENTRY(0x8cc), TBL_ENTRY(0x8cd), TBL_ENTRY(0x8ce), TBL_ENTRY(0x8cf),
+ TBL_ENTRY(0x8d0), TBL_ENTRY(0x8d1), TBL_ENTRY(0x8d2), TBL_ENTRY(0x8d3),
+ TBL_ENTRY(0x8d4), TBL_ENTRY(0x8d5), TBL_ENTRY(0x8d6), TBL_ENTRY(0x8d7),
+ TBL_ENTRY(0x8d8), TBL_ENTRY(0x8d9), TBL_ENTRY(0x8da), TBL_ENTRY(0x8db),
+ TBL_ENTRY(0x8dc), TBL_ENTRY(0x8dd), TBL_ENTRY(0x8de), TBL_ENTRY(0x8df),
+ TBL_ENTRY(0x8e0), TBL_ENTRY(0x8e1), TBL_ENTRY(0x8e2), TBL_ENTRY(0x8e3),
+ TBL_ENTRY(0x8e4), TBL_ENTRY(0x8e5), TBL_ENTRY(0x8e6), TBL_ENTRY(0x8e7),
+ TBL_ENTRY(0x8e8), TBL_ENTRY(0x8e9), TBL_ENTRY(0x8ea), TBL_ENTRY(0x8eb),
+ TBL_ENTRY(0x8ec), TBL_ENTRY(0x8ed), TBL_ENTRY(0x8ee), TBL_ENTRY(0x8ef),
+ TBL_ENTRY(0x8f0), TBL_ENTRY(0x8f1), TBL_ENTRY(0x8f2), TBL_ENTRY(0x8f3),
+ TBL_ENTRY(0x8f4), TBL_ENTRY(0x8f5), TBL_ENTRY(0x8f6), TBL_ENTRY(0x8f7),
+ TBL_ENTRY(0x8f8), TBL_ENTRY(0x8f9), TBL_ENTRY(0x8fa), TBL_ENTRY(0x8fb),
+ TBL_ENTRY(0x8fc), TBL_ENTRY(0x8fd), TBL_ENTRY(0x8fe), TBL_ENTRY(0x8ff),
+ TBL_ENTRY(0x900), TBL_ENTRY(0x901), TBL_ENTRY(0x902), TBL_ENTRY(0x903),
+ TBL_ENTRY(0x904), TBL_ENTRY(0x905), TBL_ENTRY(0x906), TBL_ENTRY(0x907),
+ TBL_ENTRY(0x908), TBL_ENTRY(0x909), TBL_ENTRY(0x90a), TBL_ENTRY(0x90b),
+ TBL_ENTRY(0x90c), TBL_ENTRY(0x90d), TBL_ENTRY(0x90e), TBL_ENTRY(0x90f),
+ TBL_ENTRY(0x910), TBL_ENTRY(0x911), TBL_ENTRY(0x912), TBL_ENTRY(0x913),
+ TBL_ENTRY(0x914), TBL_ENTRY(0x915), TBL_ENTRY(0x916), TBL_ENTRY(0x917),
+ TBL_ENTRY(0x918), TBL_ENTRY(0x919), TBL_ENTRY(0x91a), TBL_ENTRY(0x91b),
+ TBL_ENTRY(0x91c), TBL_ENTRY(0x91d), TBL_ENTRY(0x91e), TBL_ENTRY(0x91f),
+ TBL_ENTRY(0x920), TBL_ENTRY(0x921), TBL_ENTRY(0x922), TBL_ENTRY(0x923),
+ TBL_ENTRY(0x924), TBL_ENTRY(0x925), TBL_ENTRY(0x926), TBL_ENTRY(0x927),
+ TBL_ENTRY(0x928), TBL_ENTRY(0x929), TBL_ENTRY(0x92a), TBL_ENTRY(0x92b),
+ TBL_ENTRY(0x92c), TBL_ENTRY(0x92d), TBL_ENTRY(0x92e), TBL_ENTRY(0x92f),
+ TBL_ENTRY(0x930), TBL_ENTRY(0x931), TBL_ENTRY(0x932), TBL_ENTRY(0x933),
+ TBL_ENTRY(0x934), TBL_ENTRY(0x935), TBL_ENTRY(0x936), TBL_ENTRY(0x937),
+ TBL_ENTRY(0x938), TBL_ENTRY(0x939), TBL_ENTRY(0x93a), TBL_ENTRY(0x93b),
+ TBL_ENTRY(0x93c), TBL_ENTRY(0x93d), TBL_ENTRY(0x93e), TBL_ENTRY(0x93f),
+ TBL_ENTRY(0x940), TBL_ENTRY(0x941), TBL_ENTRY(0x942), TBL_ENTRY(0x943),
+ TBL_ENTRY(0x944), TBL_ENTRY(0x945), TBL_ENTRY(0x946), TBL_ENTRY(0x947),
+ TBL_ENTRY(0x948), TBL_ENTRY(0x949), TBL_ENTRY(0x94a), TBL_ENTRY(0x94b),
+ TBL_ENTRY(0x94c), TBL_ENTRY(0x94d), TBL_ENTRY(0x94e), TBL_ENTRY(0x94f),
+ TBL_ENTRY(0x950), TBL_ENTRY(0x951), TBL_ENTRY(0x952), TBL_ENTRY(0x953),
+ TBL_ENTRY(0x954), TBL_ENTRY(0x955), TBL_ENTRY(0x956), TBL_ENTRY(0x957),
+ TBL_ENTRY(0x958), TBL_ENTRY(0x959), TBL_ENTRY(0x95a), TBL_ENTRY(0x95b),
+ TBL_ENTRY(0x95c), TBL_ENTRY(0x95d), TBL_ENTRY(0x95e), TBL_ENTRY(0x95f),
+ TBL_ENTRY(0x960), TBL_ENTRY(0x961), TBL_ENTRY(0x962), TBL_ENTRY(0x963),
+ TBL_ENTRY(0x964), TBL_ENTRY(0x965), TBL_ENTRY(0x966), TBL_ENTRY(0x967),
+ TBL_ENTRY(0x968), TBL_ENTRY(0x969), TBL_ENTRY(0x96a), TBL_ENTRY(0x96b),
+ TBL_ENTRY(0x96c), TBL_ENTRY(0x96d), TBL_ENTRY(0x96e), TBL_ENTRY(0x96f),
+ TBL_ENTRY(0x970), TBL_ENTRY(0x971), TBL_ENTRY(0x972), TBL_ENTRY(0x973),
+ TBL_ENTRY(0x974), TBL_ENTRY(0x975), TBL_ENTRY(0x976), TBL_ENTRY(0x977),
+ TBL_ENTRY(0x978), TBL_ENTRY(0x979), TBL_ENTRY(0x97a), TBL_ENTRY(0x97b),
+ TBL_ENTRY(0x97c), TBL_ENTRY(0x97d), TBL_ENTRY(0x97e), TBL_ENTRY(0x97f),
+ TBL_ENTRY(0x980), TBL_ENTRY(0x981), TBL_ENTRY(0x982), TBL_ENTRY(0x983),
+ TBL_ENTRY(0x984), TBL_ENTRY(0x985), TBL_ENTRY(0x986), TBL_ENTRY(0x987),
+ TBL_ENTRY(0x988), TBL_ENTRY(0x989), TBL_ENTRY(0x98a), TBL_ENTRY(0x98b),
+ TBL_ENTRY(0x98c), TBL_ENTRY(0x98d), TBL_ENTRY(0x98e), TBL_ENTRY(0x98f),
+ TBL_ENTRY(0x990), TBL_ENTRY(0x991), TBL_ENTRY(0x992), TBL_ENTRY(0x993),
+ TBL_ENTRY(0x994), TBL_ENTRY(0x995), TBL_ENTRY(0x996), TBL_ENTRY(0x997),
+ TBL_ENTRY(0x998), TBL_ENTRY(0x999), TBL_ENTRY(0x99a), TBL_ENTRY(0x99b),
+ TBL_ENTRY(0x99c), TBL_ENTRY(0x99d), TBL_ENTRY(0x99e), TBL_ENTRY(0x99f),
+ TBL_ENTRY(0x9a0), TBL_ENTRY(0x9a1), TBL_ENTRY(0x9a2), TBL_ENTRY(0x9a3),
+ TBL_ENTRY(0x9a4), TBL_ENTRY(0x9a5), TBL_ENTRY(0x9a6), TBL_ENTRY(0x9a7),
+ TBL_ENTRY(0x9a8), TBL_ENTRY(0x9a9), TBL_ENTRY(0x9aa), TBL_ENTRY(0x9ab),
+ TBL_ENTRY(0x9ac), TBL_ENTRY(0x9ad), TBL_ENTRY(0x9ae), TBL_ENTRY(0x9af),
+ TBL_ENTRY(0x9b0), TBL_ENTRY(0x9b1), TBL_ENTRY(0x9b2), TBL_ENTRY(0x9b3),
+ TBL_ENTRY(0x9b4), TBL_ENTRY(0x9b5), TBL_ENTRY(0x9b6), TBL_ENTRY(0x9b7),
+ TBL_ENTRY(0x9b8), TBL_ENTRY(0x9b9), TBL_ENTRY(0x9ba), TBL_ENTRY(0x9bb),
+ TBL_ENTRY(0x9bc), TBL_ENTRY(0x9bd), TBL_ENTRY(0x9be), TBL_ENTRY(0x9bf),
+ TBL_ENTRY(0x9c0), TBL_ENTRY(0x9c1), TBL_ENTRY(0x9c2), TBL_ENTRY(0x9c3),
+ TBL_ENTRY(0x9c4), TBL_ENTRY(0x9c5), TBL_ENTRY(0x9c6), TBL_ENTRY(0x9c7),
+ TBL_ENTRY(0x9c8), TBL_ENTRY(0x9c9), TBL_ENTRY(0x9ca), TBL_ENTRY(0x9cb),
+ TBL_ENTRY(0x9cc), TBL_ENTRY(0x9cd), TBL_ENTRY(0x9ce), TBL_ENTRY(0x9cf),
+ TBL_ENTRY(0x9d0), TBL_ENTRY(0x9d1), TBL_ENTRY(0x9d2), TBL_ENTRY(0x9d3),
+ TBL_ENTRY(0x9d4), TBL_ENTRY(0x9d5), TBL_ENTRY(0x9d6), TBL_ENTRY(0x9d7),
+ TBL_ENTRY(0x9d8), TBL_ENTRY(0x9d9), TBL_ENTRY(0x9da), TBL_ENTRY(0x9db),
+ TBL_ENTRY(0x9dc), TBL_ENTRY(0x9dd), TBL_ENTRY(0x9de), TBL_ENTRY(0x9df),
+ TBL_ENTRY(0x9e0), TBL_ENTRY(0x9e1), TBL_ENTRY(0x9e2), TBL_ENTRY(0x9e3),
+ TBL_ENTRY(0x9e4), TBL_ENTRY(0x9e5), TBL_ENTRY(0x9e6), TBL_ENTRY(0x9e7),
+ TBL_ENTRY(0x9e8), TBL_ENTRY(0x9e9), TBL_ENTRY(0x9ea), TBL_ENTRY(0x9eb),
+ TBL_ENTRY(0x9ec), TBL_ENTRY(0x9ed), TBL_ENTRY(0x9ee), TBL_ENTRY(0x9ef),
+ TBL_ENTRY(0x9f0), TBL_ENTRY(0x9f1), TBL_ENTRY(0x9f2), TBL_ENTRY(0x9f3),
+ TBL_ENTRY(0x9f4), TBL_ENTRY(0x9f5), TBL_ENTRY(0x9f6), TBL_ENTRY(0x9f7),
+ TBL_ENTRY(0x9f8), TBL_ENTRY(0x9f9), TBL_ENTRY(0x9fa), TBL_ENTRY(0x9fb),
+ TBL_ENTRY(0x9fc), TBL_ENTRY(0x9fd), TBL_ENTRY(0x9fe), TBL_ENTRY(0x9ff),
+ TBL_ENTRY(0xa00), TBL_ENTRY(0xa01), TBL_ENTRY(0xa02), TBL_ENTRY(0xa03),
+ TBL_ENTRY(0xa04), TBL_ENTRY(0xa05), TBL_ENTRY(0xa06), TBL_ENTRY(0xa07),
+ TBL_ENTRY(0xa08), TBL_ENTRY(0xa09), TBL_ENTRY(0xa0a), TBL_ENTRY(0xa0b),
+ TBL_ENTRY(0xa0c), TBL_ENTRY(0xa0d), TBL_ENTRY(0xa0e), TBL_ENTRY(0xa0f),
+ TBL_ENTRY(0xa10), TBL_ENTRY(0xa11), TBL_ENTRY(0xa12), TBL_ENTRY(0xa13),
+ TBL_ENTRY(0xa14), TBL_ENTRY(0xa15), TBL_ENTRY(0xa16), TBL_ENTRY(0xa17),
+ TBL_ENTRY(0xa18), TBL_ENTRY(0xa19), TBL_ENTRY(0xa1a), TBL_ENTRY(0xa1b),
+ TBL_ENTRY(0xa1c), TBL_ENTRY(0xa1d), TBL_ENTRY(0xa1e), TBL_ENTRY(0xa1f),
+ TBL_ENTRY(0xa20), TBL_ENTRY(0xa21), TBL_ENTRY(0xa22), TBL_ENTRY(0xa23),
+ TBL_ENTRY(0xa24), TBL_ENTRY(0xa25), TBL_ENTRY(0xa26), TBL_ENTRY(0xa27),
+ TBL_ENTRY(0xa28), TBL_ENTRY(0xa29), TBL_ENTRY(0xa2a), TBL_ENTRY(0xa2b),
+ TBL_ENTRY(0xa2c), TBL_ENTRY(0xa2d), TBL_ENTRY(0xa2e), TBL_ENTRY(0xa2f),
+ TBL_ENTRY(0xa30), TBL_ENTRY(0xa31), TBL_ENTRY(0xa32), TBL_ENTRY(0xa33),
+ TBL_ENTRY(0xa34), TBL_ENTRY(0xa35), TBL_ENTRY(0xa36), TBL_ENTRY(0xa37),
+ TBL_ENTRY(0xa38), TBL_ENTRY(0xa39), TBL_ENTRY(0xa3a), TBL_ENTRY(0xa3b),
+ TBL_ENTRY(0xa3c), TBL_ENTRY(0xa3d), TBL_ENTRY(0xa3e), TBL_ENTRY(0xa3f),
+ TBL_ENTRY(0xa40), TBL_ENTRY(0xa41), TBL_ENTRY(0xa42), TBL_ENTRY(0xa43),
+ TBL_ENTRY(0xa44), TBL_ENTRY(0xa45), TBL_ENTRY(0xa46), TBL_ENTRY(0xa47),
+ TBL_ENTRY(0xa48), TBL_ENTRY(0xa49), TBL_ENTRY(0xa4a), TBL_ENTRY(0xa4b),
+ TBL_ENTRY(0xa4c), TBL_ENTRY(0xa4d), TBL_ENTRY(0xa4e), TBL_ENTRY(0xa4f),
+ TBL_ENTRY(0xa50), TBL_ENTRY(0xa51), TBL_ENTRY(0xa52), TBL_ENTRY(0xa53),
+ TBL_ENTRY(0xa54), TBL_ENTRY(0xa55), TBL_ENTRY(0xa56), TBL_ENTRY(0xa57),
+ TBL_ENTRY(0xa58), TBL_ENTRY(0xa59), TBL_ENTRY(0xa5a), TBL_ENTRY(0xa5b),
+ TBL_ENTRY(0xa5c), TBL_ENTRY(0xa5d), TBL_ENTRY(0xa5e), TBL_ENTRY(0xa5f),
+ TBL_ENTRY(0xa60), TBL_ENTRY(0xa61), TBL_ENTRY(0xa62), TBL_ENTRY(0xa63),
+ TBL_ENTRY(0xa64), TBL_ENTRY(0xa65), TBL_ENTRY(0xa66), TBL_ENTRY(0xa67),
+ TBL_ENTRY(0xa68), TBL_ENTRY(0xa69), TBL_ENTRY(0xa6a), TBL_ENTRY(0xa6b),
+ TBL_ENTRY(0xa6c), TBL_ENTRY(0xa6d), TBL_ENTRY(0xa6e), TBL_ENTRY(0xa6f),
+ TBL_ENTRY(0xa70), TBL_ENTRY(0xa71), TBL_ENTRY(0xa72), TBL_ENTRY(0xa73),
+ TBL_ENTRY(0xa74), TBL_ENTRY(0xa75), TBL_ENTRY(0xa76), TBL_ENTRY(0xa77),
+ TBL_ENTRY(0xa78), TBL_ENTRY(0xa79), TBL_ENTRY(0xa7a), TBL_ENTRY(0xa7b),
+ TBL_ENTRY(0xa7c), TBL_ENTRY(0xa7d), TBL_ENTRY(0xa7e), TBL_ENTRY(0xa7f),
+ TBL_ENTRY(0xa80), TBL_ENTRY(0xa81), TBL_ENTRY(0xa82), TBL_ENTRY(0xa83),
+ TBL_ENTRY(0xa84), TBL_ENTRY(0xa85), TBL_ENTRY(0xa86), TBL_ENTRY(0xa87),
+ TBL_ENTRY(0xa88), TBL_ENTRY(0xa89), TBL_ENTRY(0xa8a), TBL_ENTRY(0xa8b),
+ TBL_ENTRY(0xa8c), TBL_ENTRY(0xa8d), TBL_ENTRY(0xa8e), TBL_ENTRY(0xa8f),
+ TBL_ENTRY(0xa90), TBL_ENTRY(0xa91), TBL_ENTRY(0xa92), TBL_ENTRY(0xa93),
+ TBL_ENTRY(0xa94), TBL_ENTRY(0xa95), TBL_ENTRY(0xa96), TBL_ENTRY(0xa97),
+ TBL_ENTRY(0xa98), TBL_ENTRY(0xa99), TBL_ENTRY(0xa9a), TBL_ENTRY(0xa9b),
+ TBL_ENTRY(0xa9c), TBL_ENTRY(0xa9d), TBL_ENTRY(0xa9e), TBL_ENTRY(0xa9f),
+ TBL_ENTRY(0xaa0), TBL_ENTRY(0xaa1), TBL_ENTRY(0xaa2), TBL_ENTRY(0xaa3),
+ TBL_ENTRY(0xaa4), TBL_ENTRY(0xaa5), TBL_ENTRY(0xaa6), TBL_ENTRY(0xaa7),
+ TBL_ENTRY(0xaa8), TBL_ENTRY(0xaa9), TBL_ENTRY(0xaaa), TBL_ENTRY(0xaab),
+ TBL_ENTRY(0xaac), TBL_ENTRY(0xaad), TBL_ENTRY(0xaae), TBL_ENTRY(0xaaf),
+ TBL_ENTRY(0xab0), TBL_ENTRY(0xab1), TBL_ENTRY(0xab2), TBL_ENTRY(0xab3),
+ TBL_ENTRY(0xab4), TBL_ENTRY(0xab5), TBL_ENTRY(0xab6), TBL_ENTRY(0xab7),
+ TBL_ENTRY(0xab8), TBL_ENTRY(0xab9), TBL_ENTRY(0xaba), TBL_ENTRY(0xabb),
+ TBL_ENTRY(0xabc), TBL_ENTRY(0xabd), TBL_ENTRY(0xabe), TBL_ENTRY(0xabf),
+ TBL_ENTRY(0xac0), TBL_ENTRY(0xac1), TBL_ENTRY(0xac2), TBL_ENTRY(0xac3),
+ TBL_ENTRY(0xac4), TBL_ENTRY(0xac5), TBL_ENTRY(0xac6), TBL_ENTRY(0xac7),
+ TBL_ENTRY(0xac8), TBL_ENTRY(0xac9), TBL_ENTRY(0xaca), TBL_ENTRY(0xacb),
+ TBL_ENTRY(0xacc), TBL_ENTRY(0xacd), TBL_ENTRY(0xace), TBL_ENTRY(0xacf),
+ TBL_ENTRY(0xad0), TBL_ENTRY(0xad1), TBL_ENTRY(0xad2), TBL_ENTRY(0xad3),
+ TBL_ENTRY(0xad4), TBL_ENTRY(0xad5), TBL_ENTRY(0xad6), TBL_ENTRY(0xad7),
+ TBL_ENTRY(0xad8), TBL_ENTRY(0xad9), TBL_ENTRY(0xada), TBL_ENTRY(0xadb),
+ TBL_ENTRY(0xadc), TBL_ENTRY(0xadd), TBL_ENTRY(0xade), TBL_ENTRY(0xadf),
+ TBL_ENTRY(0xae0), TBL_ENTRY(0xae1), TBL_ENTRY(0xae2), TBL_ENTRY(0xae3),
+ TBL_ENTRY(0xae4), TBL_ENTRY(0xae5), TBL_ENTRY(0xae6), TBL_ENTRY(0xae7),
+ TBL_ENTRY(0xae8), TBL_ENTRY(0xae9), TBL_ENTRY(0xaea), TBL_ENTRY(0xaeb),
+ TBL_ENTRY(0xaec), TBL_ENTRY(0xaed), TBL_ENTRY(0xaee), TBL_ENTRY(0xaef),
+ TBL_ENTRY(0xaf0), TBL_ENTRY(0xaf1), TBL_ENTRY(0xaf2), TBL_ENTRY(0xaf3),
+ TBL_ENTRY(0xaf4), TBL_ENTRY(0xaf5), TBL_ENTRY(0xaf6), TBL_ENTRY(0xaf7),
+ TBL_ENTRY(0xaf8), TBL_ENTRY(0xaf9), TBL_ENTRY(0xafa), TBL_ENTRY(0xafb),
+ TBL_ENTRY(0xafc), TBL_ENTRY(0xafd), TBL_ENTRY(0xafe), TBL_ENTRY(0xaff),
+ TBL_ENTRY(0xb00), TBL_ENTRY(0xb01), TBL_ENTRY(0xb02), TBL_ENTRY(0xb03),
+ TBL_ENTRY(0xb04), TBL_ENTRY(0xb05), TBL_ENTRY(0xb06), TBL_ENTRY(0xb07),
+ TBL_ENTRY(0xb08), TBL_ENTRY(0xb09), TBL_ENTRY(0xb0a), TBL_ENTRY(0xb0b),
+ TBL_ENTRY(0xb0c), TBL_ENTRY(0xb0d), TBL_ENTRY(0xb0e), TBL_ENTRY(0xb0f),
+ TBL_ENTRY(0xb10), TBL_ENTRY(0xb11), TBL_ENTRY(0xb12), TBL_ENTRY(0xb13),
+ TBL_ENTRY(0xb14), TBL_ENTRY(0xb15), TBL_ENTRY(0xb16), TBL_ENTRY(0xb17),
+ TBL_ENTRY(0xb18), TBL_ENTRY(0xb19), TBL_ENTRY(0xb1a), TBL_ENTRY(0xb1b),
+ TBL_ENTRY(0xb1c), TBL_ENTRY(0xb1d), TBL_ENTRY(0xb1e), TBL_ENTRY(0xb1f),
+ TBL_ENTRY(0xb20), TBL_ENTRY(0xb21), TBL_ENTRY(0xb22), TBL_ENTRY(0xb23),
+ TBL_ENTRY(0xb24), TBL_ENTRY(0xb25), TBL_ENTRY(0xb26), TBL_ENTRY(0xb27),
+ TBL_ENTRY(0xb28), TBL_ENTRY(0xb29), TBL_ENTRY(0xb2a), TBL_ENTRY(0xb2b),
+ TBL_ENTRY(0xb2c), TBL_ENTRY(0xb2d), TBL_ENTRY(0xb2e), TBL_ENTRY(0xb2f),
+ TBL_ENTRY(0xb30), TBL_ENTRY(0xb31), TBL_ENTRY(0xb32), TBL_ENTRY(0xb33),
+ TBL_ENTRY(0xb34), TBL_ENTRY(0xb35), TBL_ENTRY(0xb36), TBL_ENTRY(0xb37),
+ TBL_ENTRY(0xb38), TBL_ENTRY(0xb39), TBL_ENTRY(0xb3a), TBL_ENTRY(0xb3b),
+ TBL_ENTRY(0xb3c), TBL_ENTRY(0xb3d), TBL_ENTRY(0xb3e), TBL_ENTRY(0xb3f),
+ TBL_ENTRY(0xb40), TBL_ENTRY(0xb41), TBL_ENTRY(0xb42), TBL_ENTRY(0xb43),
+ TBL_ENTRY(0xb44), TBL_ENTRY(0xb45), TBL_ENTRY(0xb46), TBL_ENTRY(0xb47),
+ TBL_ENTRY(0xb48), TBL_ENTRY(0xb49), TBL_ENTRY(0xb4a), TBL_ENTRY(0xb4b),
+ TBL_ENTRY(0xb4c), TBL_ENTRY(0xb4d), TBL_ENTRY(0xb4e), TBL_ENTRY(0xb4f),
+ TBL_ENTRY(0xb50), TBL_ENTRY(0xb51), TBL_ENTRY(0xb52), TBL_ENTRY(0xb53),
+ TBL_ENTRY(0xb54), TBL_ENTRY(0xb55), TBL_ENTRY(0xb56), TBL_ENTRY(0xb57),
+ TBL_ENTRY(0xb58), TBL_ENTRY(0xb59), TBL_ENTRY(0xb5a), TBL_ENTRY(0xb5b),
+ TBL_ENTRY(0xb5c), TBL_ENTRY(0xb5d), TBL_ENTRY(0xb5e), TBL_ENTRY(0xb5f),
+ TBL_ENTRY(0xb60), TBL_ENTRY(0xb61), TBL_ENTRY(0xb62), TBL_ENTRY(0xb63),
+ TBL_ENTRY(0xb64), TBL_ENTRY(0xb65), TBL_ENTRY(0xb66), TBL_ENTRY(0xb67),
+ TBL_ENTRY(0xb68), TBL_ENTRY(0xb69), TBL_ENTRY(0xb6a), TBL_ENTRY(0xb6b),
+ TBL_ENTRY(0xb6c), TBL_ENTRY(0xb6d), TBL_ENTRY(0xb6e), TBL_ENTRY(0xb6f),
+ TBL_ENTRY(0xb70), TBL_ENTRY(0xb71), TBL_ENTRY(0xb72), TBL_ENTRY(0xb73),
+ TBL_ENTRY(0xb74), TBL_ENTRY(0xb75), TBL_ENTRY(0xb76), TBL_ENTRY(0xb77),
+ TBL_ENTRY(0xb78), TBL_ENTRY(0xb79), TBL_ENTRY(0xb7a), TBL_ENTRY(0xb7b),
+ TBL_ENTRY(0xb7c), TBL_ENTRY(0xb7d), TBL_ENTRY(0xb7e), TBL_ENTRY(0xb7f),
+ TBL_ENTRY(0xb80), TBL_ENTRY(0xb81), TBL_ENTRY(0xb82), TBL_ENTRY(0xb83),
+ TBL_ENTRY(0xb84), TBL_ENTRY(0xb85), TBL_ENTRY(0xb86), TBL_ENTRY(0xb87),
+ TBL_ENTRY(0xb88), TBL_ENTRY(0xb89), TBL_ENTRY(0xb8a), TBL_ENTRY(0xb8b),
+ TBL_ENTRY(0xb8c), TBL_ENTRY(0xb8d), TBL_ENTRY(0xb8e), TBL_ENTRY(0xb8f),
+ TBL_ENTRY(0xb90), TBL_ENTRY(0xb91), TBL_ENTRY(0xb92), TBL_ENTRY(0xb93),
+ TBL_ENTRY(0xb94), TBL_ENTRY(0xb95), TBL_ENTRY(0xb96), TBL_ENTRY(0xb97),
+ TBL_ENTRY(0xb98), TBL_ENTRY(0xb99), TBL_ENTRY(0xb9a), TBL_ENTRY(0xb9b),
+ TBL_ENTRY(0xb9c), TBL_ENTRY(0xb9d), TBL_ENTRY(0xb9e), TBL_ENTRY(0xb9f),
+ TBL_ENTRY(0xba0), TBL_ENTRY(0xba1), TBL_ENTRY(0xba2), TBL_ENTRY(0xba3),
+ TBL_ENTRY(0xba4), TBL_ENTRY(0xba5), TBL_ENTRY(0xba6), TBL_ENTRY(0xba7),
+ TBL_ENTRY(0xba8), TBL_ENTRY(0xba9), TBL_ENTRY(0xbaa), TBL_ENTRY(0xbab),
+ TBL_ENTRY(0xbac), TBL_ENTRY(0xbad), TBL_ENTRY(0xbae), TBL_ENTRY(0xbaf),
+ TBL_ENTRY(0xbb0), TBL_ENTRY(0xbb1), TBL_ENTRY(0xbb2), TBL_ENTRY(0xbb3),
+ TBL_ENTRY(0xbb4), TBL_ENTRY(0xbb5), TBL_ENTRY(0xbb6), TBL_ENTRY(0xbb7),
+ TBL_ENTRY(0xbb8), TBL_ENTRY(0xbb9), TBL_ENTRY(0xbba), TBL_ENTRY(0xbbb),
+ TBL_ENTRY(0xbbc), TBL_ENTRY(0xbbd), TBL_ENTRY(0xbbe), TBL_ENTRY(0xbbf),
+ TBL_ENTRY(0xbc0), TBL_ENTRY(0xbc1), TBL_ENTRY(0xbc2), TBL_ENTRY(0xbc3),
+ TBL_ENTRY(0xbc4), TBL_ENTRY(0xbc5), TBL_ENTRY(0xbc6), TBL_ENTRY(0xbc7),
+ TBL_ENTRY(0xbc8), TBL_ENTRY(0xbc9), TBL_ENTRY(0xbca), TBL_ENTRY(0xbcb),
+ TBL_ENTRY(0xbcc), TBL_ENTRY(0xbcd), TBL_ENTRY(0xbce), TBL_ENTRY(0xbcf),
+ TBL_ENTRY(0xbd0), TBL_ENTRY(0xbd1), TBL_ENTRY(0xbd2), TBL_ENTRY(0xbd3),
+ TBL_ENTRY(0xbd4), TBL_ENTRY(0xbd5), TBL_ENTRY(0xbd6), TBL_ENTRY(0xbd7),
+ TBL_ENTRY(0xbd8), TBL_ENTRY(0xbd9), TBL_ENTRY(0xbda), TBL_ENTRY(0xbdb),
+ TBL_ENTRY(0xbdc), TBL_ENTRY(0xbdd), TBL_ENTRY(0xbde), TBL_ENTRY(0xbdf),
+ TBL_ENTRY(0xbe0), TBL_ENTRY(0xbe1), TBL_ENTRY(0xbe2), TBL_ENTRY(0xbe3),
+ TBL_ENTRY(0xbe4), TBL_ENTRY(0xbe5), TBL_ENTRY(0xbe6), TBL_ENTRY(0xbe7),
+ TBL_ENTRY(0xbe8), TBL_ENTRY(0xbe9), TBL_ENTRY(0xbea), TBL_ENTRY(0xbeb),
+ TBL_ENTRY(0xbec), TBL_ENTRY(0xbed), TBL_ENTRY(0xbee), TBL_ENTRY(0xbef),
+ TBL_ENTRY(0xbf0), TBL_ENTRY(0xbf1), TBL_ENTRY(0xbf2), TBL_ENTRY(0xbf3),
+ TBL_ENTRY(0xbf4), TBL_ENTRY(0xbf5), TBL_ENTRY(0xbf6), TBL_ENTRY(0xbf7),
+ TBL_ENTRY(0xbf8), TBL_ENTRY(0xbf9), TBL_ENTRY(0xbfa), TBL_ENTRY(0xbfb),
+ TBL_ENTRY(0xbfc), TBL_ENTRY(0xbfd), TBL_ENTRY(0xbfe), TBL_ENTRY(0xbff),
+ TBL_ENTRY(0xc00), TBL_ENTRY(0xc01), TBL_ENTRY(0xc02), TBL_ENTRY(0xc03),
+ TBL_ENTRY(0xc04), TBL_ENTRY(0xc05), TBL_ENTRY(0xc06), TBL_ENTRY(0xc07),
+ TBL_ENTRY(0xc08), TBL_ENTRY(0xc09), TBL_ENTRY(0xc0a), TBL_ENTRY(0xc0b),
+ TBL_ENTRY(0xc0c), TBL_ENTRY(0xc0d), TBL_ENTRY(0xc0e), TBL_ENTRY(0xc0f),
+ TBL_ENTRY(0xc10), TBL_ENTRY(0xc11), TBL_ENTRY(0xc12), TBL_ENTRY(0xc13),
+ TBL_ENTRY(0xc14), TBL_ENTRY(0xc15), TBL_ENTRY(0xc16), TBL_ENTRY(0xc17),
+ TBL_ENTRY(0xc18), TBL_ENTRY(0xc19), TBL_ENTRY(0xc1a), TBL_ENTRY(0xc1b),
+ TBL_ENTRY(0xc1c), TBL_ENTRY(0xc1d), TBL_ENTRY(0xc1e), TBL_ENTRY(0xc1f),
+ TBL_ENTRY(0xc20), TBL_ENTRY(0xc21), TBL_ENTRY(0xc22), TBL_ENTRY(0xc23),
+ TBL_ENTRY(0xc24), TBL_ENTRY(0xc25), TBL_ENTRY(0xc26), TBL_ENTRY(0xc27),
+ TBL_ENTRY(0xc28), TBL_ENTRY(0xc29), TBL_ENTRY(0xc2a), TBL_ENTRY(0xc2b),
+ TBL_ENTRY(0xc2c), TBL_ENTRY(0xc2d), TBL_ENTRY(0xc2e), TBL_ENTRY(0xc2f),
+ TBL_ENTRY(0xc30), TBL_ENTRY(0xc31), TBL_ENTRY(0xc32), TBL_ENTRY(0xc33),
+ TBL_ENTRY(0xc34), TBL_ENTRY(0xc35), TBL_ENTRY(0xc36), TBL_ENTRY(0xc37),
+ TBL_ENTRY(0xc38), TBL_ENTRY(0xc39), TBL_ENTRY(0xc3a), TBL_ENTRY(0xc3b),
+ TBL_ENTRY(0xc3c), TBL_ENTRY(0xc3d), TBL_ENTRY(0xc3e), TBL_ENTRY(0xc3f),
+ TBL_ENTRY(0xc40), TBL_ENTRY(0xc41), TBL_ENTRY(0xc42), TBL_ENTRY(0xc43),
+ TBL_ENTRY(0xc44), TBL_ENTRY(0xc45), TBL_ENTRY(0xc46), TBL_ENTRY(0xc47),
+ TBL_ENTRY(0xc48), TBL_ENTRY(0xc49), TBL_ENTRY(0xc4a), TBL_ENTRY(0xc4b),
+ TBL_ENTRY(0xc4c), TBL_ENTRY(0xc4d), TBL_ENTRY(0xc4e), TBL_ENTRY(0xc4f),
+ TBL_ENTRY(0xc50), TBL_ENTRY(0xc51), TBL_ENTRY(0xc52), TBL_ENTRY(0xc53),
+ TBL_ENTRY(0xc54), TBL_ENTRY(0xc55), TBL_ENTRY(0xc56), TBL_ENTRY(0xc57),
+ TBL_ENTRY(0xc58), TBL_ENTRY(0xc59), TBL_ENTRY(0xc5a), TBL_ENTRY(0xc5b),
+ TBL_ENTRY(0xc5c), TBL_ENTRY(0xc5d), TBL_ENTRY(0xc5e), TBL_ENTRY(0xc5f),
+ TBL_ENTRY(0xc60), TBL_ENTRY(0xc61), TBL_ENTRY(0xc62), TBL_ENTRY(0xc63),
+ TBL_ENTRY(0xc64), TBL_ENTRY(0xc65), TBL_ENTRY(0xc66), TBL_ENTRY(0xc67),
+ TBL_ENTRY(0xc68), TBL_ENTRY(0xc69), TBL_ENTRY(0xc6a), TBL_ENTRY(0xc6b),
+ TBL_ENTRY(0xc6c), TBL_ENTRY(0xc6d), TBL_ENTRY(0xc6e), TBL_ENTRY(0xc6f),
+ TBL_ENTRY(0xc70), TBL_ENTRY(0xc71), TBL_ENTRY(0xc72), TBL_ENTRY(0xc73),
+ TBL_ENTRY(0xc74), TBL_ENTRY(0xc75), TBL_ENTRY(0xc76), TBL_ENTRY(0xc77),
+ TBL_ENTRY(0xc78), TBL_ENTRY(0xc79), TBL_ENTRY(0xc7a), TBL_ENTRY(0xc7b),
+ TBL_ENTRY(0xc7c), TBL_ENTRY(0xc7d), TBL_ENTRY(0xc7e), TBL_ENTRY(0xc7f),
+ TBL_ENTRY(0xc80), TBL_ENTRY(0xc81), TBL_ENTRY(0xc82), TBL_ENTRY(0xc83),
+ TBL_ENTRY(0xc84), TBL_ENTRY(0xc85), TBL_ENTRY(0xc86), TBL_ENTRY(0xc87),
+ TBL_ENTRY(0xc88), TBL_ENTRY(0xc89), TBL_ENTRY(0xc8a), TBL_ENTRY(0xc8b),
+ TBL_ENTRY(0xc8c), TBL_ENTRY(0xc8d), TBL_ENTRY(0xc8e), TBL_ENTRY(0xc8f),
+ TBL_ENTRY(0xc90), TBL_ENTRY(0xc91), TBL_ENTRY(0xc92), TBL_ENTRY(0xc93),
+ TBL_ENTRY(0xc94), TBL_ENTRY(0xc95), TBL_ENTRY(0xc96), TBL_ENTRY(0xc97),
+ TBL_ENTRY(0xc98), TBL_ENTRY(0xc99), TBL_ENTRY(0xc9a), TBL_ENTRY(0xc9b),
+ TBL_ENTRY(0xc9c), TBL_ENTRY(0xc9d), TBL_ENTRY(0xc9e), TBL_ENTRY(0xc9f),
+ TBL_ENTRY(0xca0), TBL_ENTRY(0xca1), TBL_ENTRY(0xca2), TBL_ENTRY(0xca3),
+ TBL_ENTRY(0xca4), TBL_ENTRY(0xca5), TBL_ENTRY(0xca6), TBL_ENTRY(0xca7),
+ TBL_ENTRY(0xca8), TBL_ENTRY(0xca9), TBL_ENTRY(0xcaa), TBL_ENTRY(0xcab),
+ TBL_ENTRY(0xcac), TBL_ENTRY(0xcad), TBL_ENTRY(0xcae), TBL_ENTRY(0xcaf),
+ TBL_ENTRY(0xcb0), TBL_ENTRY(0xcb1), TBL_ENTRY(0xcb2), TBL_ENTRY(0xcb3),
+ TBL_ENTRY(0xcb4), TBL_ENTRY(0xcb5), TBL_ENTRY(0xcb6), TBL_ENTRY(0xcb7),
+ TBL_ENTRY(0xcb8), TBL_ENTRY(0xcb9), TBL_ENTRY(0xcba), TBL_ENTRY(0xcbb),
+ TBL_ENTRY(0xcbc), TBL_ENTRY(0xcbd), TBL_ENTRY(0xcbe), TBL_ENTRY(0xcbf),
+ TBL_ENTRY(0xcc0), TBL_ENTRY(0xcc1), TBL_ENTRY(0xcc2), TBL_ENTRY(0xcc3),
+ TBL_ENTRY(0xcc4), TBL_ENTRY(0xcc5), TBL_ENTRY(0xcc6), TBL_ENTRY(0xcc7),
+ TBL_ENTRY(0xcc8), TBL_ENTRY(0xcc9), TBL_ENTRY(0xcca), TBL_ENTRY(0xccb),
+ TBL_ENTRY(0xccc), TBL_ENTRY(0xccd), TBL_ENTRY(0xcce), TBL_ENTRY(0xccf),
+ TBL_ENTRY(0xcd0), TBL_ENTRY(0xcd1), TBL_ENTRY(0xcd2), TBL_ENTRY(0xcd3),
+ TBL_ENTRY(0xcd4), TBL_ENTRY(0xcd5), TBL_ENTRY(0xcd6), TBL_ENTRY(0xcd7),
+ TBL_ENTRY(0xcd8), TBL_ENTRY(0xcd9), TBL_ENTRY(0xcda), TBL_ENTRY(0xcdb),
+ TBL_ENTRY(0xcdc), TBL_ENTRY(0xcdd), TBL_ENTRY(0xcde), TBL_ENTRY(0xcdf),
+ TBL_ENTRY(0xce0), TBL_ENTRY(0xce1), TBL_ENTRY(0xce2), TBL_ENTRY(0xce3),
+ TBL_ENTRY(0xce4), TBL_ENTRY(0xce5), TBL_ENTRY(0xce6), TBL_ENTRY(0xce7),
+ TBL_ENTRY(0xce8), TBL_ENTRY(0xce9), TBL_ENTRY(0xcea), TBL_ENTRY(0xceb),
+ TBL_ENTRY(0xcec), TBL_ENTRY(0xced), TBL_ENTRY(0xcee), TBL_ENTRY(0xcef),
+ TBL_ENTRY(0xcf0), TBL_ENTRY(0xcf1), TBL_ENTRY(0xcf2), TBL_ENTRY(0xcf3),
+ TBL_ENTRY(0xcf4), TBL_ENTRY(0xcf5), TBL_ENTRY(0xcf6), TBL_ENTRY(0xcf7),
+ TBL_ENTRY(0xcf8), TBL_ENTRY(0xcf9), TBL_ENTRY(0xcfa), TBL_ENTRY(0xcfb),
+ TBL_ENTRY(0xcfc), TBL_ENTRY(0xcfd), TBL_ENTRY(0xcfe), TBL_ENTRY(0xcff),
+ TBL_ENTRY(0xd00), TBL_ENTRY(0xd01), TBL_ENTRY(0xd02), TBL_ENTRY(0xd03),
+ TBL_ENTRY(0xd04), TBL_ENTRY(0xd05), TBL_ENTRY(0xd06), TBL_ENTRY(0xd07),
+ TBL_ENTRY(0xd08), TBL_ENTRY(0xd09), TBL_ENTRY(0xd0a), TBL_ENTRY(0xd0b),
+ TBL_ENTRY(0xd0c), TBL_ENTRY(0xd0d), TBL_ENTRY(0xd0e), TBL_ENTRY(0xd0f),
+ TBL_ENTRY(0xd10), TBL_ENTRY(0xd11), TBL_ENTRY(0xd12), TBL_ENTRY(0xd13),
+ TBL_ENTRY(0xd14), TBL_ENTRY(0xd15), TBL_ENTRY(0xd16), TBL_ENTRY(0xd17),
+ TBL_ENTRY(0xd18), TBL_ENTRY(0xd19), TBL_ENTRY(0xd1a), TBL_ENTRY(0xd1b),
+ TBL_ENTRY(0xd1c), TBL_ENTRY(0xd1d), TBL_ENTRY(0xd1e), TBL_ENTRY(0xd1f),
+ TBL_ENTRY(0xd20), TBL_ENTRY(0xd21), TBL_ENTRY(0xd22), TBL_ENTRY(0xd23),
+ TBL_ENTRY(0xd24), TBL_ENTRY(0xd25), TBL_ENTRY(0xd26), TBL_ENTRY(0xd27),
+ TBL_ENTRY(0xd28), TBL_ENTRY(0xd29), TBL_ENTRY(0xd2a), TBL_ENTRY(0xd2b),
+ TBL_ENTRY(0xd2c), TBL_ENTRY(0xd2d), TBL_ENTRY(0xd2e), TBL_ENTRY(0xd2f),
+ TBL_ENTRY(0xd30), TBL_ENTRY(0xd31), TBL_ENTRY(0xd32), TBL_ENTRY(0xd33),
+ TBL_ENTRY(0xd34), TBL_ENTRY(0xd35), TBL_ENTRY(0xd36), TBL_ENTRY(0xd37),
+ TBL_ENTRY(0xd38), TBL_ENTRY(0xd39), TBL_ENTRY(0xd3a), TBL_ENTRY(0xd3b),
+ TBL_ENTRY(0xd3c), TBL_ENTRY(0xd3d), TBL_ENTRY(0xd3e), TBL_ENTRY(0xd3f),
+ TBL_ENTRY(0xd40), TBL_ENTRY(0xd41), TBL_ENTRY(0xd42), TBL_ENTRY(0xd43),
+ TBL_ENTRY(0xd44), TBL_ENTRY(0xd45), TBL_ENTRY(0xd46), TBL_ENTRY(0xd47),
+ TBL_ENTRY(0xd48), TBL_ENTRY(0xd49), TBL_ENTRY(0xd4a), TBL_ENTRY(0xd4b),
+ TBL_ENTRY(0xd4c), TBL_ENTRY(0xd4d), TBL_ENTRY(0xd4e), TBL_ENTRY(0xd4f),
+ TBL_ENTRY(0xd50), TBL_ENTRY(0xd51), TBL_ENTRY(0xd52), TBL_ENTRY(0xd53),
+ TBL_ENTRY(0xd54), TBL_ENTRY(0xd55), TBL_ENTRY(0xd56), TBL_ENTRY(0xd57),
+ TBL_ENTRY(0xd58), TBL_ENTRY(0xd59), TBL_ENTRY(0xd5a), TBL_ENTRY(0xd5b),
+ TBL_ENTRY(0xd5c), TBL_ENTRY(0xd5d), TBL_ENTRY(0xd5e), TBL_ENTRY(0xd5f),
+ TBL_ENTRY(0xd60), TBL_ENTRY(0xd61), TBL_ENTRY(0xd62), TBL_ENTRY(0xd63),
+ TBL_ENTRY(0xd64), TBL_ENTRY(0xd65), TBL_ENTRY(0xd66), TBL_ENTRY(0xd67),
+ TBL_ENTRY(0xd68), TBL_ENTRY(0xd69), TBL_ENTRY(0xd6a), TBL_ENTRY(0xd6b),
+ TBL_ENTRY(0xd6c), TBL_ENTRY(0xd6d), TBL_ENTRY(0xd6e), TBL_ENTRY(0xd6f),
+ TBL_ENTRY(0xd70), TBL_ENTRY(0xd71), TBL_ENTRY(0xd72), TBL_ENTRY(0xd73),
+ TBL_ENTRY(0xd74), TBL_ENTRY(0xd75), TBL_ENTRY(0xd76), TBL_ENTRY(0xd77),
+ TBL_ENTRY(0xd78), TBL_ENTRY(0xd79), TBL_ENTRY(0xd7a), TBL_ENTRY(0xd7b),
+ TBL_ENTRY(0xd7c), TBL_ENTRY(0xd7d), TBL_ENTRY(0xd7e), TBL_ENTRY(0xd7f),
+ TBL_ENTRY(0xd80), TBL_ENTRY(0xd81), TBL_ENTRY(0xd82), TBL_ENTRY(0xd83),
+ TBL_ENTRY(0xd84), TBL_ENTRY(0xd85), TBL_ENTRY(0xd86), TBL_ENTRY(0xd87),
+ TBL_ENTRY(0xd88), TBL_ENTRY(0xd89), TBL_ENTRY(0xd8a), TBL_ENTRY(0xd8b),
+ TBL_ENTRY(0xd8c), TBL_ENTRY(0xd8d), TBL_ENTRY(0xd8e), TBL_ENTRY(0xd8f),
+ TBL_ENTRY(0xd90), TBL_ENTRY(0xd91), TBL_ENTRY(0xd92), TBL_ENTRY(0xd93),
+ TBL_ENTRY(0xd94), TBL_ENTRY(0xd95), TBL_ENTRY(0xd96), TBL_ENTRY(0xd97),
+ TBL_ENTRY(0xd98), TBL_ENTRY(0xd99), TBL_ENTRY(0xd9a), TBL_ENTRY(0xd9b),
+ TBL_ENTRY(0xd9c), TBL_ENTRY(0xd9d), TBL_ENTRY(0xd9e), TBL_ENTRY(0xd9f),
+ TBL_ENTRY(0xda0), TBL_ENTRY(0xda1), TBL_ENTRY(0xda2), TBL_ENTRY(0xda3),
+ TBL_ENTRY(0xda4), TBL_ENTRY(0xda5), TBL_ENTRY(0xda6), TBL_ENTRY(0xda7),
+ TBL_ENTRY(0xda8), TBL_ENTRY(0xda9), TBL_ENTRY(0xdaa), TBL_ENTRY(0xdab),
+ TBL_ENTRY(0xdac), TBL_ENTRY(0xdad), TBL_ENTRY(0xdae), TBL_ENTRY(0xdaf),
+ TBL_ENTRY(0xdb0), TBL_ENTRY(0xdb1), TBL_ENTRY(0xdb2), TBL_ENTRY(0xdb3),
+ TBL_ENTRY(0xdb4), TBL_ENTRY(0xdb5), TBL_ENTRY(0xdb6), TBL_ENTRY(0xdb7),
+ TBL_ENTRY(0xdb8), TBL_ENTRY(0xdb9), TBL_ENTRY(0xdba), TBL_ENTRY(0xdbb),
+ TBL_ENTRY(0xdbc), TBL_ENTRY(0xdbd), TBL_ENTRY(0xdbe), TBL_ENTRY(0xdbf),
+ TBL_ENTRY(0xdc0), TBL_ENTRY(0xdc1), TBL_ENTRY(0xdc2), TBL_ENTRY(0xdc3),
+ TBL_ENTRY(0xdc4), TBL_ENTRY(0xdc5), TBL_ENTRY(0xdc6), TBL_ENTRY(0xdc7),
+ TBL_ENTRY(0xdc8), TBL_ENTRY(0xdc9), TBL_ENTRY(0xdca), TBL_ENTRY(0xdcb),
+ TBL_ENTRY(0xdcc), TBL_ENTRY(0xdcd), TBL_ENTRY(0xdce), TBL_ENTRY(0xdcf),
+ TBL_ENTRY(0xdd0), TBL_ENTRY(0xdd1), TBL_ENTRY(0xdd2), TBL_ENTRY(0xdd3),
+ TBL_ENTRY(0xdd4), TBL_ENTRY(0xdd5), TBL_ENTRY(0xdd6), TBL_ENTRY(0xdd7),
+ TBL_ENTRY(0xdd8), TBL_ENTRY(0xdd9), TBL_ENTRY(0xdda), TBL_ENTRY(0xddb),
+ TBL_ENTRY(0xddc), TBL_ENTRY(0xddd), TBL_ENTRY(0xdde), TBL_ENTRY(0xddf),
+ TBL_ENTRY(0xde0), TBL_ENTRY(0xde1), TBL_ENTRY(0xde2), TBL_ENTRY(0xde3),
+ TBL_ENTRY(0xde4), TBL_ENTRY(0xde5), TBL_ENTRY(0xde6), TBL_ENTRY(0xde7),
+ TBL_ENTRY(0xde8), TBL_ENTRY(0xde9), TBL_ENTRY(0xdea), TBL_ENTRY(0xdeb),
+ TBL_ENTRY(0xdec), TBL_ENTRY(0xded), TBL_ENTRY(0xdee), TBL_ENTRY(0xdef),
+ TBL_ENTRY(0xdf0), TBL_ENTRY(0xdf1), TBL_ENTRY(0xdf2), TBL_ENTRY(0xdf3),
+ TBL_ENTRY(0xdf4), TBL_ENTRY(0xdf5), TBL_ENTRY(0xdf6), TBL_ENTRY(0xdf7),
+ TBL_ENTRY(0xdf8), TBL_ENTRY(0xdf9), TBL_ENTRY(0xdfa), TBL_ENTRY(0xdfb),
+ TBL_ENTRY(0xdfc), TBL_ENTRY(0xdfd), TBL_ENTRY(0xdfe), TBL_ENTRY(0xdff),
+ TBL_ENTRY(0xe00), TBL_ENTRY(0xe01), TBL_ENTRY(0xe02), TBL_ENTRY(0xe03),
+ TBL_ENTRY(0xe04), TBL_ENTRY(0xe05), TBL_ENTRY(0xe06), TBL_ENTRY(0xe07),
+ TBL_ENTRY(0xe08), TBL_ENTRY(0xe09), TBL_ENTRY(0xe0a), TBL_ENTRY(0xe0b),
+ TBL_ENTRY(0xe0c), TBL_ENTRY(0xe0d), TBL_ENTRY(0xe0e), TBL_ENTRY(0xe0f),
+ TBL_ENTRY(0xe10), TBL_ENTRY(0xe11), TBL_ENTRY(0xe12), TBL_ENTRY(0xe13),
+ TBL_ENTRY(0xe14), TBL_ENTRY(0xe15), TBL_ENTRY(0xe16), TBL_ENTRY(0xe17),
+ TBL_ENTRY(0xe18), TBL_ENTRY(0xe19), TBL_ENTRY(0xe1a), TBL_ENTRY(0xe1b),
+ TBL_ENTRY(0xe1c), TBL_ENTRY(0xe1d), TBL_ENTRY(0xe1e), TBL_ENTRY(0xe1f),
+ TBL_ENTRY(0xe20), TBL_ENTRY(0xe21), TBL_ENTRY(0xe22), TBL_ENTRY(0xe23),
+ TBL_ENTRY(0xe24), TBL_ENTRY(0xe25), TBL_ENTRY(0xe26), TBL_ENTRY(0xe27),
+ TBL_ENTRY(0xe28), TBL_ENTRY(0xe29), TBL_ENTRY(0xe2a), TBL_ENTRY(0xe2b),
+ TBL_ENTRY(0xe2c), TBL_ENTRY(0xe2d), TBL_ENTRY(0xe2e), TBL_ENTRY(0xe2f),
+ TBL_ENTRY(0xe30), TBL_ENTRY(0xe31), TBL_ENTRY(0xe32), TBL_ENTRY(0xe33),
+ TBL_ENTRY(0xe34), TBL_ENTRY(0xe35), TBL_ENTRY(0xe36), TBL_ENTRY(0xe37),
+ TBL_ENTRY(0xe38), TBL_ENTRY(0xe39), TBL_ENTRY(0xe3a), TBL_ENTRY(0xe3b),
+ TBL_ENTRY(0xe3c), TBL_ENTRY(0xe3d), TBL_ENTRY(0xe3e), TBL_ENTRY(0xe3f),
+ TBL_ENTRY(0xe40), TBL_ENTRY(0xe41), TBL_ENTRY(0xe42), TBL_ENTRY(0xe43),
+ TBL_ENTRY(0xe44), TBL_ENTRY(0xe45), TBL_ENTRY(0xe46), TBL_ENTRY(0xe47),
+ TBL_ENTRY(0xe48), TBL_ENTRY(0xe49), TBL_ENTRY(0xe4a), TBL_ENTRY(0xe4b),
+ TBL_ENTRY(0xe4c), TBL_ENTRY(0xe4d), TBL_ENTRY(0xe4e), TBL_ENTRY(0xe4f),
+ TBL_ENTRY(0xe50), TBL_ENTRY(0xe51), TBL_ENTRY(0xe52), TBL_ENTRY(0xe53),
+ TBL_ENTRY(0xe54), TBL_ENTRY(0xe55), TBL_ENTRY(0xe56), TBL_ENTRY(0xe57),
+ TBL_ENTRY(0xe58), TBL_ENTRY(0xe59), TBL_ENTRY(0xe5a), TBL_ENTRY(0xe5b),
+ TBL_ENTRY(0xe5c), TBL_ENTRY(0xe5d), TBL_ENTRY(0xe5e), TBL_ENTRY(0xe5f),
+ TBL_ENTRY(0xe60), TBL_ENTRY(0xe61), TBL_ENTRY(0xe62), TBL_ENTRY(0xe63),
+ TBL_ENTRY(0xe64), TBL_ENTRY(0xe65), TBL_ENTRY(0xe66), TBL_ENTRY(0xe67),
+ TBL_ENTRY(0xe68), TBL_ENTRY(0xe69), TBL_ENTRY(0xe6a), TBL_ENTRY(0xe6b),
+ TBL_ENTRY(0xe6c), TBL_ENTRY(0xe6d), TBL_ENTRY(0xe6e), TBL_ENTRY(0xe6f),
+ TBL_ENTRY(0xe70), TBL_ENTRY(0xe71), TBL_ENTRY(0xe72), TBL_ENTRY(0xe73),
+ TBL_ENTRY(0xe74), TBL_ENTRY(0xe75), TBL_ENTRY(0xe76), TBL_ENTRY(0xe77),
+ TBL_ENTRY(0xe78), TBL_ENTRY(0xe79), TBL_ENTRY(0xe7a), TBL_ENTRY(0xe7b),
+ TBL_ENTRY(0xe7c), TBL_ENTRY(0xe7d), TBL_ENTRY(0xe7e), TBL_ENTRY(0xe7f),
+ TBL_ENTRY(0xe80), TBL_ENTRY(0xe81), TBL_ENTRY(0xe82), TBL_ENTRY(0xe83),
+ TBL_ENTRY(0xe84), TBL_ENTRY(0xe85), TBL_ENTRY(0xe86), TBL_ENTRY(0xe87),
+ TBL_ENTRY(0xe88), TBL_ENTRY(0xe89), TBL_ENTRY(0xe8a), TBL_ENTRY(0xe8b),
+ TBL_ENTRY(0xe8c), TBL_ENTRY(0xe8d), TBL_ENTRY(0xe8e), TBL_ENTRY(0xe8f),
+ TBL_ENTRY(0xe90), TBL_ENTRY(0xe91), TBL_ENTRY(0xe92), TBL_ENTRY(0xe93),
+ TBL_ENTRY(0xe94), TBL_ENTRY(0xe95), TBL_ENTRY(0xe96), TBL_ENTRY(0xe97),
+ TBL_ENTRY(0xe98), TBL_ENTRY(0xe99), TBL_ENTRY(0xe9a), TBL_ENTRY(0xe9b),
+ TBL_ENTRY(0xe9c), TBL_ENTRY(0xe9d), TBL_ENTRY(0xe9e), TBL_ENTRY(0xe9f),
+ TBL_ENTRY(0xea0), TBL_ENTRY(0xea1), TBL_ENTRY(0xea2), TBL_ENTRY(0xea3),
+ TBL_ENTRY(0xea4), TBL_ENTRY(0xea5), TBL_ENTRY(0xea6), TBL_ENTRY(0xea7),
+ TBL_ENTRY(0xea8), TBL_ENTRY(0xea9), TBL_ENTRY(0xeaa), TBL_ENTRY(0xeab),
+ TBL_ENTRY(0xeac), TBL_ENTRY(0xead), TBL_ENTRY(0xeae), TBL_ENTRY(0xeaf),
+ TBL_ENTRY(0xeb0), TBL_ENTRY(0xeb1), TBL_ENTRY(0xeb2), TBL_ENTRY(0xeb3),
+ TBL_ENTRY(0xeb4), TBL_ENTRY(0xeb5), TBL_ENTRY(0xeb6), TBL_ENTRY(0xeb7),
+ TBL_ENTRY(0xeb8), TBL_ENTRY(0xeb9), TBL_ENTRY(0xeba), TBL_ENTRY(0xebb),
+ TBL_ENTRY(0xebc), TBL_ENTRY(0xebd), TBL_ENTRY(0xebe), TBL_ENTRY(0xebf),
+ TBL_ENTRY(0xec0), TBL_ENTRY(0xec1), TBL_ENTRY(0xec2), TBL_ENTRY(0xec3),
+ TBL_ENTRY(0xec4), TBL_ENTRY(0xec5), TBL_ENTRY(0xec6), TBL_ENTRY(0xec7),
+ TBL_ENTRY(0xec8), TBL_ENTRY(0xec9), TBL_ENTRY(0xeca), TBL_ENTRY(0xecb),
+ TBL_ENTRY(0xecc), TBL_ENTRY(0xecd), TBL_ENTRY(0xece), TBL_ENTRY(0xecf),
+ TBL_ENTRY(0xed0), TBL_ENTRY(0xed1), TBL_ENTRY(0xed2), TBL_ENTRY(0xed3),
+ TBL_ENTRY(0xed4), TBL_ENTRY(0xed5), TBL_ENTRY(0xed6), TBL_ENTRY(0xed7),
+ TBL_ENTRY(0xed8), TBL_ENTRY(0xed9), TBL_ENTRY(0xeda), TBL_ENTRY(0xedb),
+ TBL_ENTRY(0xedc), TBL_ENTRY(0xedd), TBL_ENTRY(0xede), TBL_ENTRY(0xedf),
+ TBL_ENTRY(0xee0), TBL_ENTRY(0xee1), TBL_ENTRY(0xee2), TBL_ENTRY(0xee3),
+ TBL_ENTRY(0xee4), TBL_ENTRY(0xee5), TBL_ENTRY(0xee6), TBL_ENTRY(0xee7),
+ TBL_ENTRY(0xee8), TBL_ENTRY(0xee9), TBL_ENTRY(0xeea), TBL_ENTRY(0xeeb),
+ TBL_ENTRY(0xeec), TBL_ENTRY(0xeed), TBL_ENTRY(0xeee), TBL_ENTRY(0xeef),
+ TBL_ENTRY(0xef0), TBL_ENTRY(0xef1), TBL_ENTRY(0xef2), TBL_ENTRY(0xef3),
+ TBL_ENTRY(0xef4), TBL_ENTRY(0xef5), TBL_ENTRY(0xef6), TBL_ENTRY(0xef7),
+ TBL_ENTRY(0xef8), TBL_ENTRY(0xef9), TBL_ENTRY(0xefa), TBL_ENTRY(0xefb),
+ TBL_ENTRY(0xefc), TBL_ENTRY(0xefd), TBL_ENTRY(0xefe), TBL_ENTRY(0xeff),
+ TBL_ENTRY(0xf00), TBL_ENTRY(0xf01), TBL_ENTRY(0xf02), TBL_ENTRY(0xf03),
+ TBL_ENTRY(0xf04), TBL_ENTRY(0xf05), TBL_ENTRY(0xf06), TBL_ENTRY(0xf07),
+ TBL_ENTRY(0xf08), TBL_ENTRY(0xf09), TBL_ENTRY(0xf0a), TBL_ENTRY(0xf0b),
+ TBL_ENTRY(0xf0c), TBL_ENTRY(0xf0d), TBL_ENTRY(0xf0e), TBL_ENTRY(0xf0f),
+ TBL_ENTRY(0xf10), TBL_ENTRY(0xf11), TBL_ENTRY(0xf12), TBL_ENTRY(0xf13),
+ TBL_ENTRY(0xf14), TBL_ENTRY(0xf15), TBL_ENTRY(0xf16), TBL_ENTRY(0xf17),
+ TBL_ENTRY(0xf18), TBL_ENTRY(0xf19), TBL_ENTRY(0xf1a), TBL_ENTRY(0xf1b),
+ TBL_ENTRY(0xf1c), TBL_ENTRY(0xf1d), TBL_ENTRY(0xf1e), TBL_ENTRY(0xf1f),
+ TBL_ENTRY(0xf20), TBL_ENTRY(0xf21), TBL_ENTRY(0xf22), TBL_ENTRY(0xf23),
+ TBL_ENTRY(0xf24), TBL_ENTRY(0xf25), TBL_ENTRY(0xf26), TBL_ENTRY(0xf27),
+ TBL_ENTRY(0xf28), TBL_ENTRY(0xf29), TBL_ENTRY(0xf2a), TBL_ENTRY(0xf2b),
+ TBL_ENTRY(0xf2c), TBL_ENTRY(0xf2d), TBL_ENTRY(0xf2e), TBL_ENTRY(0xf2f),
+ TBL_ENTRY(0xf30), TBL_ENTRY(0xf31), TBL_ENTRY(0xf32), TBL_ENTRY(0xf33),
+ TBL_ENTRY(0xf34), TBL_ENTRY(0xf35), TBL_ENTRY(0xf36), TBL_ENTRY(0xf37),
+ TBL_ENTRY(0xf38), TBL_ENTRY(0xf39), TBL_ENTRY(0xf3a), TBL_ENTRY(0xf3b),
+ TBL_ENTRY(0xf3c), TBL_ENTRY(0xf3d), TBL_ENTRY(0xf3e), TBL_ENTRY(0xf3f),
+ TBL_ENTRY(0xf40), TBL_ENTRY(0xf41), TBL_ENTRY(0xf42), TBL_ENTRY(0xf43),
+ TBL_ENTRY(0xf44), TBL_ENTRY(0xf45), TBL_ENTRY(0xf46), TBL_ENTRY(0xf47),
+ TBL_ENTRY(0xf48), TBL_ENTRY(0xf49), TBL_ENTRY(0xf4a), TBL_ENTRY(0xf4b),
+ TBL_ENTRY(0xf4c), TBL_ENTRY(0xf4d), TBL_ENTRY(0xf4e), TBL_ENTRY(0xf4f),
+ TBL_ENTRY(0xf50), TBL_ENTRY(0xf51), TBL_ENTRY(0xf52), TBL_ENTRY(0xf53),
+ TBL_ENTRY(0xf54), TBL_ENTRY(0xf55), TBL_ENTRY(0xf56), TBL_ENTRY(0xf57),
+ TBL_ENTRY(0xf58), TBL_ENTRY(0xf59), TBL_ENTRY(0xf5a), TBL_ENTRY(0xf5b),
+ TBL_ENTRY(0xf5c), TBL_ENTRY(0xf5d), TBL_ENTRY(0xf5e), TBL_ENTRY(0xf5f),
+ TBL_ENTRY(0xf60), TBL_ENTRY(0xf61), TBL_ENTRY(0xf62), TBL_ENTRY(0xf63),
+ TBL_ENTRY(0xf64), TBL_ENTRY(0xf65), TBL_ENTRY(0xf66), TBL_ENTRY(0xf67),
+ TBL_ENTRY(0xf68), TBL_ENTRY(0xf69), TBL_ENTRY(0xf6a), TBL_ENTRY(0xf6b),
+ TBL_ENTRY(0xf6c), TBL_ENTRY(0xf6d), TBL_ENTRY(0xf6e), TBL_ENTRY(0xf6f),
+ TBL_ENTRY(0xf70), TBL_ENTRY(0xf71), TBL_ENTRY(0xf72), TBL_ENTRY(0xf73),
+ TBL_ENTRY(0xf74), TBL_ENTRY(0xf75), TBL_ENTRY(0xf76), TBL_ENTRY(0xf77),
+ TBL_ENTRY(0xf78), TBL_ENTRY(0xf79), TBL_ENTRY(0xf7a), TBL_ENTRY(0xf7b),
+ TBL_ENTRY(0xf7c), TBL_ENTRY(0xf7d), TBL_ENTRY(0xf7e), TBL_ENTRY(0xf7f),
+ TBL_ENTRY(0xf80), TBL_ENTRY(0xf81), TBL_ENTRY(0xf82), TBL_ENTRY(0xf83),
+ TBL_ENTRY(0xf84), TBL_ENTRY(0xf85), TBL_ENTRY(0xf86), TBL_ENTRY(0xf87),
+ TBL_ENTRY(0xf88), TBL_ENTRY(0xf89), TBL_ENTRY(0xf8a), TBL_ENTRY(0xf8b),
+ TBL_ENTRY(0xf8c), TBL_ENTRY(0xf8d), TBL_ENTRY(0xf8e), TBL_ENTRY(0xf8f),
+ TBL_ENTRY(0xf90), TBL_ENTRY(0xf91), TBL_ENTRY(0xf92), TBL_ENTRY(0xf93),
+ TBL_ENTRY(0xf94), TBL_ENTRY(0xf95), TBL_ENTRY(0xf96), TBL_ENTRY(0xf97),
+ TBL_ENTRY(0xf98), TBL_ENTRY(0xf99), TBL_ENTRY(0xf9a), TBL_ENTRY(0xf9b),
+ TBL_ENTRY(0xf9c), TBL_ENTRY(0xf9d), TBL_ENTRY(0xf9e), TBL_ENTRY(0xf9f),
+ TBL_ENTRY(0xfa0), TBL_ENTRY(0xfa1), TBL_ENTRY(0xfa2), TBL_ENTRY(0xfa3),
+ TBL_ENTRY(0xfa4), TBL_ENTRY(0xfa5), TBL_ENTRY(0xfa6), TBL_ENTRY(0xfa7),
+ TBL_ENTRY(0xfa8), TBL_ENTRY(0xfa9), TBL_ENTRY(0xfaa), TBL_ENTRY(0xfab),
+ TBL_ENTRY(0xfac), TBL_ENTRY(0xfad), TBL_ENTRY(0xfae), TBL_ENTRY(0xfaf),
+ TBL_ENTRY(0xfb0), TBL_ENTRY(0xfb1), TBL_ENTRY(0xfb2), TBL_ENTRY(0xfb3),
+ TBL_ENTRY(0xfb4), TBL_ENTRY(0xfb5), TBL_ENTRY(0xfb6), TBL_ENTRY(0xfb7),
+ TBL_ENTRY(0xfb8), TBL_ENTRY(0xfb9), TBL_ENTRY(0xfba), TBL_ENTRY(0xfbb),
+ TBL_ENTRY(0xfbc), TBL_ENTRY(0xfbd), TBL_ENTRY(0xfbe), TBL_ENTRY(0xfbf),
+ TBL_ENTRY(0xfc0), TBL_ENTRY(0xfc1), TBL_ENTRY(0xfc2), TBL_ENTRY(0xfc3),
+ TBL_ENTRY(0xfc4), TBL_ENTRY(0xfc5), TBL_ENTRY(0xfc6), TBL_ENTRY(0xfc7),
+ TBL_ENTRY(0xfc8), TBL_ENTRY(0xfc9), TBL_ENTRY(0xfca), TBL_ENTRY(0xfcb),
+ TBL_ENTRY(0xfcc), TBL_ENTRY(0xfcd), TBL_ENTRY(0xfce), TBL_ENTRY(0xfcf),
+ TBL_ENTRY(0xfd0), TBL_ENTRY(0xfd1), TBL_ENTRY(0xfd2), TBL_ENTRY(0xfd3),
+ TBL_ENTRY(0xfd4), TBL_ENTRY(0xfd5), TBL_ENTRY(0xfd6), TBL_ENTRY(0xfd7),
+ TBL_ENTRY(0xfd8), TBL_ENTRY(0xfd9), TBL_ENTRY(0xfda), TBL_ENTRY(0xfdb),
+ TBL_ENTRY(0xfdc), TBL_ENTRY(0xfdd), TBL_ENTRY(0xfde), TBL_ENTRY(0xfdf),
+ TBL_ENTRY(0xfe0), TBL_ENTRY(0xfe1), TBL_ENTRY(0xfe2), TBL_ENTRY(0xfe3),
+ TBL_ENTRY(0xfe4), TBL_ENTRY(0xfe5), TBL_ENTRY(0xfe6), TBL_ENTRY(0xfe7),
+ TBL_ENTRY(0xfe8), TBL_ENTRY(0xfe9), TBL_ENTRY(0xfea), TBL_ENTRY(0xfeb),
+ TBL_ENTRY(0xfec), TBL_ENTRY(0xfed), TBL_ENTRY(0xfee), TBL_ENTRY(0xfef),
+ TBL_ENTRY(0xff0), TBL_ENTRY(0xff1), TBL_ENTRY(0xff2), TBL_ENTRY(0xff3),
+ TBL_ENTRY(0xff4), TBL_ENTRY(0xff5), TBL_ENTRY(0xff6), TBL_ENTRY(0xff7),
+ TBL_ENTRY(0xff8), TBL_ENTRY(0xff9), TBL_ENTRY(0xffa), TBL_ENTRY(0xffb),
+ TBL_ENTRY(0xffc), TBL_ENTRY(0xffd), TBL_ENTRY(0xffe), TBL_ENTRY(0xfff),
+};
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <config.h>
+#include <linux/linkage.h>
+#include <asm/system.h>
+#include <asm/arch/led.h>
+#include <asm/arch/arm-mpcore.h>
+#include <asm/arch/sbc-regs.h>
+
+ENTRY(lowlevel_init)
+ mov r8, lr @ persevere link reg across call
+
+ /*
+ * The UniPhier Boot ROM loads SPL code to the L2 cache.
+ * But CPUs can only do instruction fetch now because start.S has
+ * cleared C and M bits.
+ * First we need to turn on MMU and Dcache again to get back
+ * data access to L2.
+ */
+ mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
+ orr r0, r0, #(CR_C | CR_M) @ enable MMU and Dcache
+ mcr p15, 0, r0, c1, c0, 0
+
+ /*
+ * Now we are using the page table embedded in the Boot ROM.
+ * It is not handy since it is not a straight mapped table for sLD3.
+ * What we need to do next is to switch over to the page table in SPL.
+ */
+ ldr r3, =init_page_table @ page table must be 16KB aligned
+
+ /* Disable MMU and Dcache before switching Page Table */
+ mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
+ bic r0, r0, #(CR_C | CR_M) @ disable MMU and Dcache
+ mcr p15, 0, r0, c1, c0, 0
+
+ bl enable_mmu
+
+#ifdef CONFIG_UNIPHIER_SMP
+ /*
+ * ACTLR (Auxiliary Control Register) for Cortex-A9
+ * bit[9] Parity on
+ * bit[8] Alloc in one way
+ * bit[7] EXCL (Exclusive cache bit)
+ * bit[6] SMP
+ * bit[3] Write full line of zeros mode
+ * bit[2] L1 Prefetch enable
+ * bit[1] L2 prefetch enable
+ * bit[0] FW (Cache and TLB maintenance broadcast)
+ */
+ mrc p15, 0, r0, c1, c0, 1 @ ACTLR (Auxiliary Control Register)
+ orr r0, r0, #0x41 @ enable SMP, FW bit
+ mcr p15, 0, r0, c1, c0, 1
+
+ /* branch by CPU ID */
+ mrc p15, 0, r0, c0, c0, 5 @ MPIDR (Multiprocessor Affinity Register)
+ and r0, r0, #0x3
+ cmp r0, #0x0
+ beq primary_cpu
+ ldr r1, =ROM_BOOT_ROMRSV2
+ mov r0, #0
+ str r0, [r1]
+0: wfe
+ ldr r0, [r1]
+ cmp r0, #0
+ beq 0b
+ bx r0 @ r0: entry point of U-Boot main for the secondary CPU
+primary_cpu:
+ ldr r1, =ROM_BOOT_ROMRSV2
+ ldr r0, =_start @ entry for the secondary CPU
+ str r0, [r1]
+ ldr r0, [r1] @ make sure str is complete before sev
+ sev @ kick the sedoncary CPU
+ mrc p15, 4, r1, c15, c0, 0 @ Configuration Base Address Register
+ bfc r1, #0, #13 @ clear bit 12-0
+ mov r0, #-1
+ str r0, [r1, #SCU_INV_ALL] @ SCU Invalidate All Register
+ mov r0, #1 @ SCU enable
+ str r0, [r1, #SCU_CTRL] @ SCU Control Register
+#endif
+
+ bl setup_init_ram @ RAM area for temporary stack pointer
+
+ mov lr, r8 @ restore link
+ mov pc, lr @ back to my caller
+ENDPROC(lowlevel_init)
+
+ENTRY(enable_mmu)
+ mrc p15, 0, r0, c2, c0, 2 @ TTBCR (Translation Table Base Control Register)
+ bic r0, r0, #0x37
+ orr r0, r0, #0x20 @ disable TTBR1
+ mcr p15, 0, r0, c2, c0, 2
+
+ orr r0, r3, #0x8 @ Outer Cacheability for table walks: WBWA
+ mcr p15, 0, r0, c2, c0, 0 @ TTBR0
+
+ mov r0, #0
+ mcr p15, 0, r0, c8, c7, 0 @ invalidate TLBs
+
+ mov r0, #-1 @ manager for all domains (No permission check)
+ mcr p15, 0, r0, c3, c0, 0 @ DACR (Domain Access Control Register)
+
+ dsb
+ isb
+ /*
+ * MMU on:
+ * TLBs was already invalidated in "../start.S"
+ * So, we don't need to invalidate it here.
+ */
+ mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
+ orr r0, r0, #(CR_C | CR_M) @ MMU and Dcache enable
+ mcr p15, 0, r0, c1, c0, 0
+
+ mov pc, lr
+ENDPROC(enable_mmu)
+
+#include <asm/arch/ssc-regs.h>
+
+#define BOOT_RAM_SIZE (SSC_WAY_SIZE)
+#define BOOT_WAY_BITS (0x00000100) /* way 8 */
+
+ENTRY(setup_init_ram)
+ /*
+ * Touch to zero for the boot way
+ */
+0:
+ /*
+ * set SSCOQM, SSCOQAD, SSCOQSZ, SSCOQWN in this order
+ */
+ ldr r0, = 0x00408006 @ touch to zero with address range
+ ldr r1, = SSCOQM
+ str r0, [r1]
+ ldr r0, = (CONFIG_SYS_INIT_SP_ADDR - BOOT_RAM_SIZE) @ base address
+ ldr r1, = SSCOQAD
+ str r0, [r1]
+ ldr r0, = BOOT_RAM_SIZE
+ ldr r1, = SSCOQSZ
+ str r0, [r1]
+ ldr r0, = BOOT_WAY_BITS
+ ldr r1, = SSCOQWN
+ str r0, [r1]
+ ldr r1, = SSCOPPQSEF
+ ldr r0, [r1]
+ cmp r0, #0 @ check if the command is successfully set
+ bne 0b @ try again if an error occurres
+
+ ldr r1, = SSCOLPQS
+1:
+ ldr r0, [r1]
+ cmp r0, #0x4
+ bne 1b @ wait until the operation is completed
+ str r0, [r1] @ clear the complete notification flag
+
+ mov pc, lr
+ENDPROC(setup_init_ram)
--- /dev/null
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-$(CONFIG_DISPLAY_BOARDINFO) += board_info.o
+obj-y += boot-mode.o
+obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o bcu_init.o \
+ sbc_init.o sg_init.o pll_init.o clkrst_init.o pinctrl.o
+obj-$(CONFIG_SPL_BUILD) += pll_spectrum.o \
+ umc_init.o
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/bcu-regs.h>
+
+#define ch(x) ((x) >= 32 ? 0 : (x) < 0 ? 0x11111111 : 0x11111111 << (x))
+
+void bcu_init(void)
+{
+ int shift;
+
+ writel(0x44444444, BCSCR0); /* 0x20000000-0x3fffffff: ASM bus */
+ writel(0x11111111, BCSCR2); /* 0x80000000-0x9fffffff: IPPC/IPPD-bus */
+ writel(0x11111111, BCSCR3); /* 0xa0000000-0xbfffffff: IPPC/IPPD-bus */
+ writel(0x11111111, BCSCR4); /* 0xc0000000-0xdfffffff: IPPC/IPPD-bus */
+ writel(0x11111111, BCSCR5); /* 0xe0000000-0Xffffffff: IPPC/IPPD-bus */
+
+ /* Specify DDR channel */
+ shift = (CONFIG_SDRAM1_BASE - CONFIG_SDRAM0_BASE) / 0x04000000 * 4;
+ writel(ch(shift), BCIPPCCHR2); /* 0x80000000-0x9fffffff */
+
+ shift -= 32;
+ writel(ch(shift), BCIPPCCHR3); /* 0xa0000000-0xbfffffff */
+
+ shift -= 32;
+ writel(ch(shift), BCIPPCCHR4); /* 0xc0000000-0xdfffffff */
+}
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/board.h>
+
+int checkboard(void)
+{
+ puts("Board: PH1-LD4 Board\n");
+
+ return check_support_card();
+}
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/led.h>
+#include <asm/arch/board.h>
+
+void bcu_init(void);
+void sbc_init(void);
+void sg_init(void);
+void pll_init(void);
+void pin_init(void);
+void clkrst_init(void);
+
+int board_postclk_init(void)
+{
+ bcu_init();
+
+ sbc_init();
+
+ sg_init();
+
+ pll_init();
+
+ uniphier_board_init();
+
+ led_write(B, 1, , );
+
+ clkrst_init();
+
+ led_write(B, 2, , );
+
+ pin_init();
+
+ led_write(B, 3, , );
+
+ return 0;
+}
--- /dev/null
+#include "../ph1-pro4/boot-mode.c"
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sc-regs.h>
+
+void clkrst_init(void)
+{
+ u32 tmp;
+
+ /* deassert reset */
+ tmp = readl(SC_RSTCTRL);
+ tmp |= SC_RSTCTRL_NRST_ETHER | SC_RSTCTRL_NRST_UMC1
+ | SC_RSTCTRL_NRST_UMC0 | SC_RSTCTRL_NRST_NAND;
+ writel(tmp, SC_RSTCTRL);
+ readl(SC_RSTCTRL); /* dummy read */
+
+ /* privide clocks */
+ tmp = readl(SC_CLKCTRL);
+ tmp |= SC_CLKCTRL_CLK_ETHER | SC_CLKCTRL_CLK_MIO | SC_CLKCTRL_CLK_UMC
+ | SC_CLKCTRL_CLK_NAND | SC_CLKCTRL_CLK_SBC | SC_CLKCTRL_CLK_PERI;
+ writel(tmp, SC_CLKCTRL);
+ readl(SC_CLKCTRL); /* dummy read */
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sg-regs.h>
+
+void pin_init(void)
+{
+ u32 tmp;
+
+ /* Comment format: PAD Name -> Function Name */
+
+#ifdef CONFIG_UNIPHIER_SERIAL
+ sg_set_pinsel(85, 1); /* HSDOUT3 -> RXD0 */
+ sg_set_pinsel(88, 1); /* HDDOUT6 -> TXD0 */
+
+ sg_set_pinsel(69, 23); /* PCIOWR -> TXD1 */
+ sg_set_pinsel(70, 23); /* PCIORD -> RXD1 */
+
+ sg_set_pinsel(128, 13); /* XIRQ6 -> TXD2 */
+ sg_set_pinsel(129, 13); /* XIRQ7 -> RXD2 */
+
+ sg_set_pinsel(110, 1); /* SBO0 -> TXD3 */
+ sg_set_pinsel(111, 1); /* SBI0 -> RXD3 */
+#endif
+
+#ifdef CONFIG_NAND_DENALI
+ sg_set_pinsel(158, 0); /* XNFRE -> XNFRE_GB */
+ sg_set_pinsel(159, 0); /* XNFWE -> XNFWE_GB */
+ sg_set_pinsel(160, 0); /* XFALE -> NFALE_GB */
+ sg_set_pinsel(161, 0); /* XFCLE -> NFCLE_GB */
+ sg_set_pinsel(162, 0); /* XNFWP -> XFNWP_GB */
+ sg_set_pinsel(163, 0); /* XNFCE0 -> XNFCE0_GB */
+ sg_set_pinsel(164, 0); /* NANDRYBY0 -> NANDRYBY0_GB */
+ sg_set_pinsel(22, 0); /* MMCCLK -> XFNCE1_GB */
+ sg_set_pinsel(23, 0); /* MMCCMD -> NANDRYBY1_GB */
+ sg_set_pinsel(24, 0); /* MMCDAT0 -> NFD0_GB */
+ sg_set_pinsel(25, 0); /* MMCDAT1 -> NFD1_GB */
+ sg_set_pinsel(26, 0); /* MMCDAT2 -> NFD2_GB */
+ sg_set_pinsel(27, 0); /* MMCDAT3 -> NFD3_GB */
+ sg_set_pinsel(28, 0); /* MMCDAT4 -> NFD4_GB */
+ sg_set_pinsel(29, 0); /* MMCDAT5 -> NFD5_GB */
+ sg_set_pinsel(30, 0); /* MMCDAT6 -> NFD6_GB */
+ sg_set_pinsel(31, 0); /* MMCDAT7 -> NFD7_GB */
+#endif
+
+#ifdef CONFIG_USB_EHCI_UNIPHIER
+ sg_set_pinsel(53, 0); /* USB0VBUS -> USB0VBUS */
+ sg_set_pinsel(54, 0); /* USB0OD -> USB0OD */
+ sg_set_pinsel(55, 0); /* USB1VBUS -> USB1VBUS */
+ sg_set_pinsel(56, 0); /* USB1OD -> USB1OD */
+ /* sg_set_pinsel(67, 23); */ /* PCOE -> USB2VBUS */
+ /* sg_set_pinsel(68, 23); */ /* PCWAIT -> USB2OD */
+#endif
+
+ tmp = readl(SG_IECTRL);
+ tmp |= 0x41;
+ writel(tmp, SG_IECTRL);
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sc-regs.h>
+#include <asm/arch/sg-regs.h>
+
+#undef DPLL_SSC_RATE_1PER
+
+void dpll_init(void)
+{
+ u32 tmp;
+
+ /*
+ * Set Frequency
+ * Set 0xc(1600MHz)/0xd(1333MHz)/0xe(1066MHz)
+ * to FOUT (DPLLCTRL.bit[29:20])
+ */
+ tmp = readl(SC_DPLLCTRL);
+ tmp &= ~0x000f0000;
+#if CONFIG_DDR_FREQ == 1600
+ tmp |= 0x000c0000;
+#elif CONFIG_DDR_FREQ == 1333
+ tmp |= 0x000d0000;
+#else
+# error "Unknown frequency"
+#endif
+
+#if defined(DPLL_SSC_RATE_1PER)
+ tmp &= ~SC_DPLLCTRL_SSC_RATE;
+#else
+ tmp |= SC_DPLLCTRL_SSC_RATE;
+#endif
+ writel(tmp, SC_DPLLCTRL);
+
+ tmp = readl(SC_DPLLCTRL2);
+ tmp |= SC_DPLLCTRL2_NRSTDS;
+ writel(tmp, SC_DPLLCTRL2);
+}
+
+void upll_init(void)
+{
+ u32 tmp, clk_mode_upll, clk_mode_axosel;
+
+ tmp = readl(SG_PINMON0);
+ clk_mode_upll = tmp & SG_PINMON0_CLK_MODE_UPLLSRC_MASK;
+ clk_mode_axosel = tmp & SG_PINMON0_CLK_MODE_AXOSEL_MASK;
+
+ /* set 0 to SNRT(UPLLCTRL.bit28) and K_LD(UPLLCTRL.bit[27]) */
+ tmp = readl(SC_UPLLCTRL);
+ tmp &= ~0x18000000;
+ writel(tmp, SC_UPLLCTRL);
+
+ if (clk_mode_upll == SG_PINMON0_CLK_MODE_UPLLSRC_DEFAULT) {
+ if (clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_U ||
+ clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_A) {
+ /* AXO: 25MHz */
+ tmp &= ~0x07ffffff;
+ tmp |= 0x0228f5c0;
+ } else {
+ /* AXO: default 24.576MHz */
+ tmp &= ~0x07ffffff;
+ tmp |= 0x02328000;
+ }
+ }
+
+ writel(tmp, SC_UPLLCTRL);
+
+ /* set 1 to K_LD(UPLLCTRL.bit[27]) */
+ tmp |= 0x08000000;
+ writel(tmp, SC_UPLLCTRL);
+
+ /* wait 10 usec */
+ udelay(10);
+
+ /* set 1 to SNRT(UPLLCTRL.bit[28]) */
+ tmp |= 0x10000000;
+ writel(tmp, SC_UPLLCTRL);
+}
+
+void vpll_init(void)
+{
+ u32 tmp, clk_mode_axosel;
+
+ tmp = readl(SG_PINMON0);
+ clk_mode_axosel = tmp & SG_PINMON0_CLK_MODE_AXOSEL_MASK;
+
+ /* set 1 to VPLA27WP and VPLA27WP */
+ tmp = readl(SC_VPLL27ACTRL);
+ tmp |= 0x00000001;
+ writel(tmp, SC_VPLL27ACTRL);
+ tmp = readl(SC_VPLL27BCTRL);
+ tmp |= 0x00000001;
+ writel(tmp, SC_VPLL27BCTRL);
+
+ /* Set 0 to VPLA_K_LD and VPLB_K_LD */
+ tmp = readl(SC_VPLL27ACTRL3);
+ tmp &= ~0x10000000;
+ writel(tmp, SC_VPLL27ACTRL3);
+ tmp = readl(SC_VPLL27BCTRL3);
+ tmp &= ~0x10000000;
+ writel(tmp, SC_VPLL27BCTRL3);
+
+ /* Set 0 to VPLA_SNRST and VPLB_SNRST */
+ tmp = readl(SC_VPLL27ACTRL2);
+ tmp &= ~0x10000000;
+ writel(tmp, SC_VPLL27ACTRL2);
+ tmp = readl(SC_VPLL27BCTRL2);
+ tmp &= ~0x10000000;
+ writel(tmp, SC_VPLL27BCTRL2);
+
+ /* Set 0x20 to VPLA_SNRST and VPLB_SNRST */
+ tmp = readl(SC_VPLL27ACTRL2);
+ tmp &= ~0x0000007f;
+ tmp |= 0x00000020;
+ writel(tmp, SC_VPLL27ACTRL2);
+ tmp = readl(SC_VPLL27BCTRL2);
+ tmp &= ~0x0000007f;
+ tmp |= 0x00000020;
+ writel(tmp, SC_VPLL27BCTRL2);
+
+ if (clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_U ||
+ clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_A) {
+ /* AXO: 25MHz */
+ tmp = readl(SC_VPLL27ACTRL3);
+ tmp &= ~0x000fffff;
+ tmp |= 0x00066664;
+ writel(tmp, SC_VPLL27ACTRL3);
+ tmp = readl(SC_VPLL27BCTRL3);
+ tmp &= ~0x000fffff;
+ tmp |= 0x00066664;
+ writel(tmp, SC_VPLL27BCTRL3);
+ } else {
+ /* AXO: default 24.576MHz */
+ tmp = readl(SC_VPLL27ACTRL3);
+ tmp &= ~0x000fffff;
+ tmp |= 0x000f5800;
+ writel(tmp, SC_VPLL27ACTRL3);
+ tmp = readl(SC_VPLL27BCTRL3);
+ tmp &= ~0x000fffff;
+ tmp |= 0x000f5800;
+ writel(tmp, SC_VPLL27BCTRL3);
+ }
+
+ /* Set 1 to VPLA_K_LD and VPLB_K_LD */
+ tmp = readl(SC_VPLL27ACTRL3);
+ tmp |= 0x10000000;
+ writel(tmp, SC_VPLL27ACTRL3);
+ tmp = readl(SC_VPLL27BCTRL3);
+ tmp |= 0x10000000;
+ writel(tmp, SC_VPLL27BCTRL3);
+
+ /* wait 10 usec */
+ udelay(10);
+
+ /* Set 0 to VPLA_SNRST and VPLB_SNRST */
+ tmp = readl(SC_VPLL27ACTRL2);
+ tmp |= 0x10000000;
+ writel(tmp, SC_VPLL27ACTRL2);
+ tmp = readl(SC_VPLL27BCTRL2);
+ tmp |= 0x10000000;
+ writel(tmp, SC_VPLL27BCTRL2);
+
+ /* set 0 to VPLA27WP and VPLA27WP */
+ tmp = readl(SC_VPLL27ACTRL);
+ tmp &= ~0x00000001;
+ writel(tmp, SC_VPLL27ACTRL);
+ tmp = readl(SC_VPLL27BCTRL);
+ tmp |= ~0x00000001;
+ writel(tmp, SC_VPLL27BCTRL);
+}
+
+void pll_init(void)
+{
+ dpll_init();
+ upll_init();
+ vpll_init();
+
+ /*
+ * Wait 500 usec until dpll get stable
+ * We wait 10 usec in upll_init() and vpll_init()
+ * so 20 usec can be saved here.
+ */
+ udelay(480);
+}
--- /dev/null
+#include "../ph1-pro4/pll_spectrum.c"
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sbc-regs.h>
+#include <asm/arch/sg-regs.h>
+
+void sbc_init(void)
+{
+ /* XECS1: sub/boot memory (boot swap = off/on) */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL10);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL11);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL12);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL14);
+
+#if !defined(CONFIG_SPL_BUILD)
+ /* XECS0: boot/sub memory (boot swap = off/on) */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL00);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL01);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL02);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL04);
+#endif
+ /* XECS3: peripherals */
+ writel(SBCTRL0_SAVEPIN_PERI_VALUE, SBCTRL30);
+ writel(SBCTRL1_SAVEPIN_PERI_VALUE, SBCTRL31);
+ writel(SBCTRL2_SAVEPIN_PERI_VALUE, SBCTRL32);
+ writel(SBCTRL4_SAVEPIN_PERI_VALUE, SBCTRL34);
+
+ /* base address regsiters */
+ writel(0x0000bc01, SBBASE0);
+ writel(0x0400bc01, SBBASE1);
+ writel(0x0800bf01, SBBASE3);
+
+#if !defined(CONFIG_SPL_BUILD)
+ /* enable access to sub memory when boot swap is on */
+ sg_set_pinsel(155, 1); /* PORT24 -> XECS0 */
+#endif
+ sg_set_pinsel(156, 1); /* PORT25 -> XECS3 */
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sg-regs.h>
+
+void sg_init(void)
+{
+ u32 tmp;
+
+ /* Set DDR size */
+ tmp = sg_memconf_val_ch0(CONFIG_SDRAM0_SIZE, CONFIG_DDR_NUM_CH0);
+ tmp |= sg_memconf_val_ch1(CONFIG_SDRAM1_SIZE, CONFIG_DDR_NUM_CH1);
+#if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE < CONFIG_SDRAM1_BASE
+ tmp |= SG_MEMCONF_SPARSEMEM;
+#endif
+ writel(tmp, SG_MEMCONF);
+
+ /* Input ports must be enabled deasserting reset of cores */
+ tmp = readl(SG_IECTRL);
+ tmp |= 0x1;
+ writel(tmp, SG_IECTRL);
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/umc-regs.h>
+
+static inline void umc_start_ssif(void __iomem *ssif_base)
+{
+ writel(0x00000000, ssif_base + 0x0000b004);
+ writel(0xffffffff, ssif_base + 0x0000c004);
+ writel(0x000fffcf, ssif_base + 0x0000c008);
+ writel(0x00000001, ssif_base + 0x0000b000);
+ writel(0x00000001, ssif_base + 0x0000c000);
+ writel(0x03010101, ssif_base + UMC_MDMCHSEL);
+ writel(0x03010100, ssif_base + UMC_DMDCHSEL);
+
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_FETCH);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMQUE0);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMWC0);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMRC0);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMQUE1);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMWC1);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMRC1);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_WC);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_RC);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_DST);
+
+ writel(0x00000001, ssif_base + UMC_CPURST);
+ writel(0x00000001, ssif_base + UMC_IDSRST);
+ writel(0x00000001, ssif_base + UMC_IXMRST);
+ writel(0x00000001, ssif_base + UMC_MDMRST);
+ writel(0x00000001, ssif_base + UMC_MDDRST);
+ writel(0x00000001, ssif_base + UMC_SIORST);
+ writel(0x00000001, ssif_base + UMC_VIORST);
+ writel(0x00000001, ssif_base + UMC_FRCRST);
+ writel(0x00000001, ssif_base + UMC_RGLRST);
+ writel(0x00000001, ssif_base + UMC_AIORST);
+ writel(0x00000001, ssif_base + UMC_DMDRST);
+}
+
+void umc_dramcont_init(void __iomem *dramcont, void __iomem *ca_base,
+ int size, int freq)
+{
+ if (freq == 1333) {
+ writel(0x45990b11, dramcont + UMC_CMDCTLA);
+ writel(0x16958924, dramcont + UMC_CMDCTLB);
+ writel(0x5101046A, dramcont + UMC_INITCTLA);
+
+ if (size == 1)
+ writel(0x27028B0A, dramcont + UMC_INITCTLB);
+ else if (size == 2)
+ writel(0x38028B0A, dramcont + UMC_INITCTLB);
+
+ writel(0x000FF0FF, dramcont + UMC_INITCTLC);
+ writel(0x00000b51, dramcont + UMC_DRMMR0);
+ } else if (freq == 1600) {
+ writel(0x36BB0F17, dramcont + UMC_CMDCTLA);
+ writel(0x18C6AA24, dramcont + UMC_CMDCTLB);
+ writel(0x5101387F, dramcont + UMC_INITCTLA);
+
+ if (size == 1)
+ writel(0x2F030D3F, dramcont + UMC_INITCTLB);
+ else if (size == 2)
+ writel(0x43030D3F, dramcont + UMC_INITCTLB);
+
+ writel(0x00FF00FF, dramcont + UMC_INITCTLC);
+ writel(0x00000d71, dramcont + UMC_DRMMR0);
+ }
+
+ writel(0x00000006, dramcont + UMC_DRMMR1);
+
+ if (freq == 1333)
+ writel(0x00000290, dramcont + UMC_DRMMR2);
+ else if (freq == 1600)
+ writel(0x00000298, dramcont + UMC_DRMMR2);
+
+ writel(0x00000800, dramcont + UMC_DRMMR3);
+
+ if (freq == 1333) {
+ if (size == 1)
+ writel(0x00240512, dramcont + UMC_SPCCTLA);
+ else if (size == 2)
+ writel(0x00350512, dramcont + UMC_SPCCTLA);
+
+ writel(0x00ff0006, dramcont + UMC_SPCCTLB);
+ writel(0x000a00ac, dramcont + UMC_RDATACTL_D0);
+ } else if (freq == 1600) {
+ if (size == 1)
+ writel(0x002B0617, dramcont + UMC_SPCCTLA);
+ else if (size == 2)
+ writel(0x003F0617, dramcont + UMC_SPCCTLA);
+
+ writel(0x00ff0008, dramcont + UMC_SPCCTLB);
+ writel(0x000c00ae, dramcont + UMC_RDATACTL_D0);
+ }
+
+ writel(0x04060806, dramcont + UMC_WDATACTL_D0);
+ writel(0x04a02000, dramcont + UMC_DATASET);
+ writel(0x00000000, ca_base + 0x2300);
+ writel(0x00400020, dramcont + UMC_DCCGCTL);
+ writel(0x00000003, dramcont + 0x7000);
+ writel(0x0000000f, dramcont + 0x8000);
+ writel(0x000000c3, dramcont + 0x8004);
+ writel(0x00000071, dramcont + 0x8008);
+ writel(0x0000003b, dramcont + UMC_DICGCTLA);
+ writel(0x020a0808, dramcont + UMC_DICGCTLB);
+ writel(0x00000004, dramcont + UMC_FLOWCTLG);
+ writel(0x80000201, ca_base + 0xc20);
+ writel(0x0801e01e, dramcont + UMC_FLOWCTLA);
+ writel(0x00200000, dramcont + UMC_FLOWCTLB);
+ writel(0x00004444, dramcont + UMC_FLOWCTLC);
+ writel(0x200a0a00, dramcont + UMC_SPCSETB);
+ writel(0x00000000, dramcont + UMC_SPCSETD);
+ writel(0x00000520, dramcont + UMC_DFICUPDCTLA);
+}
+
+static inline int umc_init_sub(int freq, int size_ch0, int size_ch1)
+{
+ void __iomem *ssif_base = (void __iomem *)UMC_SSIF_BASE;
+ void __iomem *ca_base0 = (void __iomem *)UMC_CA_BASE(0);
+ void __iomem *ca_base1 = (void __iomem *)UMC_CA_BASE(1);
+ void __iomem *dramcont0 = (void __iomem *)UMC_DRAMCONT_BASE(0);
+ void __iomem *dramcont1 = (void __iomem *)UMC_DRAMCONT_BASE(1);
+
+ umc_dram_init_start(dramcont0);
+ umc_dram_init_start(dramcont1);
+ umc_dram_init_poll(dramcont0);
+ umc_dram_init_poll(dramcont1);
+
+ writel(0x00000101, dramcont0 + UMC_DIOCTLA);
+
+ writel(0x00000101, dramcont1 + UMC_DIOCTLA);
+
+ umc_dramcont_init(dramcont0, ca_base0, size_ch0, freq);
+ umc_dramcont_init(dramcont1, ca_base1, size_ch1, freq);
+
+ umc_start_ssif(ssif_base);
+
+ return 0;
+}
+
+int umc_init(void)
+{
+ return umc_init_sub(CONFIG_DDR_FREQ, CONFIG_SDRAM0_SIZE / 0x08000000,
+ CONFIG_SDRAM1_SIZE / 0x08000000);
+}
+
+#if CONFIG_DDR_FREQ != 1333 && CONFIG_DDR_FREQ != 1600
+#error Unsupported DDR Frequency.
+#endif
+
+#if (CONFIG_SDRAM0_SIZE == 0x08000000 || CONFIG_SDRAM0_SIZE == 0x10000000) && \
+ (CONFIG_SDRAM1_SIZE == 0x08000000 || CONFIG_SDRAM1_SIZE == 0x10000000) && \
+ CONFIG_DDR_NUM_CH0 == 1 && CONFIG_DDR_NUM_CH1 == 1
+/* OK */
+#else
+#error Unsupported DDR configuration.
+#endif
--- /dev/null
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-$(CONFIG_DISPLAY_BOARDINFO) += board_info.o
+obj-y += boot-mode.o
+obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o sbc_init.o \
+ sg_init.o pll_init.o clkrst_init.o pinctrl.o
+obj-$(CONFIG_SPL_BUILD) += pll_spectrum.o \
+ umc_init.o
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/board.h>
+
+int checkboard(void)
+{
+ puts("Board: PH1-Pro4 Board\n");
+
+ return check_support_card();
+}
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/led.h>
+#include <asm/arch/board.h>
+
+void sbc_init(void);
+void sg_init(void);
+void pll_init(void);
+void pin_init(void);
+void clkrst_init(void);
+
+int board_postclk_init(void)
+{
+ sbc_init();
+
+ sg_init();
+
+ pll_init();
+
+ uniphier_board_init();
+
+ led_write(B, 1, , );
+
+ clkrst_init();
+
+ led_write(B, 2, , );
+
+ pin_init();
+
+ led_write(B, 3, , );
+
+ return 0;
+}
--- /dev/null
+/*
+ * Copyright (C) 2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <asm/arch/boot-device.h>
+#include <asm/arch/sg-regs.h>
+#include <asm/arch/sbc-regs.h>
+
+struct boot_device_info boot_device_table[] = {
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 8, EraseSize 128KB, Addr 4)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 8, EraseSize 128KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 16, EraseSize 128KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 8, EraseSize 256KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 16, EraseSize 256KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 8, EraseSize 512KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 16, EraseSize 512KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 24, EraseSize 1MB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 4, ECC 24, EraseSize 1MB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 8, EraseSize 128KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 16, EraseSize 128KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 8, EraseSize 256KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 16, EraseSize 256KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 8, EraseSize 512KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 16, EraseSize 512KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 24, EraseSize 512KB, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 8, ONFI, Addr 4)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 8, ONFI, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 16, ONFI, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 8, ECC 24, ONFI, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 4, ECC 24, ONFI, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 8, ONFI, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 16, ONFI, Addr 5)"},
+ {BOOT_DEVICE_NAND, "NAND (Mirror 1, ECC 24, ONFI, Addr 5)"},
+ {BOOT_DEVICE_MMC1, "eMMC Boot (3.3V)"},
+ {BOOT_DEVICE_MMC1, "eMMC Boot (1.8V)"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_NONE, "Reserved"},
+ {BOOT_DEVICE_NONE, ""}
+};
+
+u32 get_boot_mode_sel(void)
+{
+ return (readl(SG_PINMON0) >> 1) & 0x1f;
+}
+
+u32 spl_boot_device(void)
+{
+ u32 boot_mode;
+
+ if (boot_is_swapped())
+ return BOOT_DEVICE_NOR;
+
+ boot_mode = get_boot_mode_sel();
+
+ return boot_device_table[boot_mode].type;
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sc-regs.h>
+
+void clkrst_init(void)
+{
+ u32 tmp;
+
+ /* deassert reset */
+ tmp = readl(SC_RSTCTRL);
+ tmp |= SC_RSTCTRL_NRST_ETHER | SC_RSTCTRL_NRST_UMC1
+ | SC_RSTCTRL_NRST_UMC0 | SC_RSTCTRL_NRST_NAND;
+ writel(tmp, SC_RSTCTRL);
+ readl(SC_RSTCTRL); /* dummy read */
+
+ /* privide clocks */
+ tmp = readl(SC_CLKCTRL);
+ tmp |= SC_CLKCTRL_CLK_ETHER | SC_CLKCTRL_CLK_MIO | SC_CLKCTRL_CLK_UMC
+ | SC_CLKCTRL_CLK_NAND | SC_CLKCTRL_CLK_SBC | SC_CLKCTRL_CLK_PERI;
+ writel(tmp, SC_CLKCTRL);
+ readl(SC_CLKCTRL); /* dummy read */
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sg-regs.h>
+
+void pin_init(void)
+{
+ /* Comment format: PAD Name -> Function Name */
+
+#ifdef CONFIG_UNIPHIER_SERIAL
+ sg_set_pinsel(127, 0); /* RXD0 -> RXD0 */
+ sg_set_pinsel(128, 0); /* TXD0 -> TXD0 */
+ sg_set_pinsel(129, 0); /* RXD1 -> RXD1 */
+ sg_set_pinsel(130, 0); /* TXD1 -> TXD1 */
+ sg_set_pinsel(131, 0); /* RXD2 -> RXD2 */
+ sg_set_pinsel(132, 0); /* TXD2 -> TXD2 */
+ sg_set_pinsel(88, 2); /* CH6CLK -> RXD3 */
+ sg_set_pinsel(89, 2); /* CH6VAL -> TXD3 */
+#endif
+
+#ifdef CONFIG_NAND_DENALI
+ sg_set_pinsel(40, 0); /* NFD0 -> NFD0 */
+ sg_set_pinsel(41, 0); /* NFD1 -> NFD1 */
+ sg_set_pinsel(42, 0); /* NFD2 -> NFD2 */
+ sg_set_pinsel(43, 0); /* NFD3 -> NFD3 */
+ sg_set_pinsel(44, 0); /* NFD4 -> NFD4 */
+ sg_set_pinsel(45, 0); /* NFD5 -> NFD5 */
+ sg_set_pinsel(46, 0); /* NFD6 -> NFD6 */
+ sg_set_pinsel(47, 0); /* NFD7 -> NFD7 */
+ sg_set_pinsel(48, 0); /* NFALE -> NFALE */
+ sg_set_pinsel(49, 0); /* NFCLE -> NFCLE */
+ sg_set_pinsel(50, 0); /* XNFRE -> XNFRE */
+ sg_set_pinsel(51, 0); /* XNFWE -> XNFWE */
+ sg_set_pinsel(52, 0); /* XNFWP -> XNFWP */
+ sg_set_pinsel(53, 0); /* XNFCE0 -> XNFCE0 */
+ sg_set_pinsel(54, 0); /* NRYBY0 -> NRYBY0 */
+#endif
+
+ writel(1, SG_LOADPINCTRL);
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sc-regs.h>
+#include <asm/arch/sg-regs.h>
+
+#undef DPLL_SSC_RATE_1PER
+
+void dpll_init(void)
+{
+ u32 tmp;
+
+ /*
+ * Set Frequency
+ * Set 0xc(1600MHz)/0xd(1333MHz)/0xe(1066MHz)
+ * to FOUT ( DPLLCTRL.bit[29:20] )
+ */
+ tmp = readl(SC_DPLLCTRL);
+ tmp &= ~(0x000f0000);
+#if CONFIG_DDR_FREQ == 1600
+ tmp |= 0x000c0000;
+#elif CONFIG_DDR_FREQ == 1333
+ tmp |= 0x000d0000;
+#else
+# error "Unsupported frequency"
+#endif
+
+ /*
+ * Set Moduration rate
+ * Set 0x0(1%)/0x1(2%) to SSC_RATE(DPLLCTRL.bit[15])
+ */
+#if defined(DPLL_SSC_RATE_1PER)
+ tmp &= ~0x00008000;
+#else
+ tmp |= 0x00008000;
+#endif
+ writel(tmp, SC_DPLLCTRL);
+
+ tmp = readl(SC_DPLLCTRL2);
+ tmp |= SC_DPLLCTRL2_NRSTDS;
+ writel(tmp, SC_DPLLCTRL2);
+}
+
+void stop_mpll(void)
+{
+ u32 tmp;
+
+ tmp = readl(SC_MPLLOSCCTL);
+
+ if (!(tmp & SC_MPLLOSCCTL_MPLLST))
+ return; /* already stopped */
+
+ tmp &= ~SC_MPLLOSCCTL_MPLLEN;
+ writel(tmp, SC_MPLLOSCCTL);
+
+ while (readl(SC_MPLLOSCCTL) & SC_MPLLOSCCTL_MPLLST)
+ ;
+}
+
+void vpll_init(void)
+{
+ u32 tmp, clk_mode_axosel;
+
+ /* Set VPLL27A & VPLL27B */
+ tmp = readl(SG_PINMON0);
+ clk_mode_axosel = tmp & SG_PINMON0_CLK_MODE_AXOSEL_MASK;
+
+#if defined(CONFIG_MACH_PH1_PRO4)
+ /* 25MHz or 6.25MHz is default for Pro4R, no need to set VPLLA/B */
+ if (clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ ||
+ clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_6250KHZ)
+ return;
+#endif
+
+ /* Disable write protect of VPLL27ACTRL[2-7]*, VPLL27BCTRL[2-8] */
+ tmp = readl(SC_VPLL27ACTRL);
+ tmp |= 0x00000001;
+ writel(tmp, SC_VPLL27ACTRL);
+ tmp = readl(SC_VPLL27BCTRL);
+ tmp |= 0x00000001;
+ writel(tmp, SC_VPLL27BCTRL);
+
+ /* Unset VPLA_K_LD and VPLB_K_LD bit */
+ tmp = readl(SC_VPLL27ACTRL3);
+ tmp &= ~0x10000000;
+ writel(tmp, SC_VPLL27ACTRL3);
+ tmp = readl(SC_VPLL27BCTRL3);
+ tmp &= ~0x10000000;
+ writel(tmp, SC_VPLL27BCTRL3);
+
+ /* Set VPLA_M and VPLB_M to 0x20 */
+ tmp = readl(SC_VPLL27ACTRL2);
+ tmp &= ~0x0000007f;
+ tmp |= 0x00000020;
+ writel(tmp, SC_VPLL27ACTRL2);
+ tmp = readl(SC_VPLL27BCTRL2);
+ tmp &= ~0x0000007f;
+ tmp |= 0x00000020;
+ writel(tmp, SC_VPLL27BCTRL2);
+
+ if (clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ ||
+ clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_6250KHZ) {
+ /* Set VPLA_K and VPLB_K for AXO: 25MHz */
+ tmp = readl(SC_VPLL27ACTRL3);
+ tmp &= ~0x000fffff;
+ tmp |= 0x00066666;
+ writel(tmp, SC_VPLL27ACTRL3);
+ tmp = readl(SC_VPLL27BCTRL3);
+ tmp &= ~0x000fffff;
+ tmp |= 0x00066666;
+ writel(tmp, SC_VPLL27BCTRL3);
+ } else {
+ /* Set VPLA_K and VPLB_K for AXO: 24.576 MHz */
+ tmp = readl(SC_VPLL27ACTRL3);
+ tmp &= ~0x000fffff;
+ tmp |= 0x000f5800;
+ writel(tmp, SC_VPLL27ACTRL3);
+ tmp = readl(SC_VPLL27BCTRL3);
+ tmp &= ~0x000fffff;
+ tmp |= 0x000f5800;
+ writel(tmp, SC_VPLL27BCTRL3);
+ }
+
+ /* wait 1 usec */
+ udelay(1);
+
+ /* Set VPLA_K_LD and VPLB_K_LD to load K parameters */
+ tmp = readl(SC_VPLL27ACTRL3);
+ tmp |= 0x10000000;
+ writel(tmp, SC_VPLL27ACTRL3);
+ tmp = readl(SC_VPLL27BCTRL3);
+ tmp |= 0x10000000;
+ writel(tmp, SC_VPLL27BCTRL3);
+
+ /* Unset VPLA_SNRST and VPLB_SNRST bit */
+ tmp = readl(SC_VPLL27ACTRL2);
+ tmp |= 0x10000000;
+ writel(tmp, SC_VPLL27ACTRL2);
+ tmp = readl(SC_VPLL27BCTRL2);
+ tmp |= 0x10000000;
+ writel(tmp, SC_VPLL27BCTRL2);
+
+ /* Enable write protect of VPLL27ACTRL[2-7]*, VPLL27BCTRL[2-8] */
+ tmp = readl(SC_VPLL27ACTRL);
+ tmp &= ~0x00000001;
+ writel(tmp, SC_VPLL27ACTRL);
+ tmp = readl(SC_VPLL27BCTRL);
+ tmp &= ~0x00000001;
+ writel(tmp, SC_VPLL27BCTRL);
+}
+
+void pll_init(void)
+{
+ dpll_init();
+ stop_mpll();
+ vpll_init();
+
+ /*
+ * Wait 500 usec until dpll get stable
+ * We wait 1 usec in vpll_init() so 1 usec can be saved here.
+ */
+ udelay(499);
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sc-regs.h>
+
+void enable_dpll_ssc(void)
+{
+ u32 tmp;
+
+ tmp = readl(SC_DPLLCTRL);
+ tmp |= SC_DPLLCTRL_SSC_EN;
+ writel(tmp, SC_DPLLCTRL);
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sbc-regs.h>
+#include <asm/arch/sg-regs.h>
+
+void sbc_init(void)
+{
+#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
+ /*
+ * Only CS1 is connected to support card.
+ * BKSZ[1:0] should be set to "01".
+ */
+ writel(SBCTRL0_SAVEPIN_PERI_VALUE, SBCTRL10);
+ writel(SBCTRL1_SAVEPIN_PERI_VALUE, SBCTRL11);
+ writel(SBCTRL2_SAVEPIN_PERI_VALUE, SBCTRL12);
+ writel(SBCTRL4_SAVEPIN_PERI_VALUE, SBCTRL14);
+
+ if (readl(SBBASE0) & 0x1) {
+ /*
+ * Boot Swap Off: boot from mask ROM
+ * 0x00000000-0x01ffffff: mask ROM
+ * 0x02000000-0x3effffff: memory bank (31MB)
+ * 0x03f00000-0x3fffffff: peripherals (1MB)
+ */
+ writel(0x0000be01, SBBASE0); /* dummy */
+ writel(0x0200be01, SBBASE1);
+ } else {
+ /*
+ * Boot Swap On: boot from external NOR/SRAM
+ * 0x02000000-0x03ffffff is a mirror of 0x00000000-0x01ffffff.
+ *
+ * 0x00000000-0x01efffff, 0x02000000-0x03efffff: memory bank
+ * 0x01f00000-0x01ffffff, 0x03f00000-0x03ffffff: peripherals
+ */
+ writel(0x0000bc01, SBBASE0);
+ }
+#elif defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
+#if !defined(CONFIG_SPL_BUILD)
+ /* XECS0: boot/sub memory (boot swap = off/on) */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL00);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL01);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL02);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL04);
+#endif
+ /* XECS1: sub/boot memory (boot swap = off/on) */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL10);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL11);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL12);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL14);
+
+ /* XECS3: peripherals */
+ writel(SBCTRL0_SAVEPIN_PERI_VALUE, SBCTRL30);
+ writel(SBCTRL1_SAVEPIN_PERI_VALUE, SBCTRL31);
+ writel(SBCTRL2_SAVEPIN_PERI_VALUE, SBCTRL32);
+ writel(SBCTRL4_SAVEPIN_PERI_VALUE, SBCTRL34);
+
+ writel(0x0000bc01, SBBASE0); /* boot memory */
+ writel(0x0400bc01, SBBASE1); /* sub memory */
+ writel(0x0800bf01, SBBASE3); /* peripherals */
+
+#if !defined(CONFIG_SPL_BUILD)
+ sg_set_pinsel(318, 5); /* PORT22 -> XECS0 */
+#endif
+ sg_set_pinsel(313, 5); /* PORT15 -> XECS3 */
+ writel(0x00000001, SG_LOADPINCTRL);
+
+#endif /* CONFIG_XXX_MICRO_SUPPORT_CARD */
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sg-regs.h>
+
+void sg_init(void)
+{
+ u32 tmp;
+
+ /* Set DDR size */
+ tmp = sg_memconf_val_ch0(CONFIG_SDRAM0_SIZE, CONFIG_DDR_NUM_CH0);
+ tmp |= sg_memconf_val_ch1(CONFIG_SDRAM1_SIZE, CONFIG_DDR_NUM_CH1);
+#if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE < CONFIG_SDRAM1_BASE
+ tmp |= SG_MEMCONF_SPARSEMEM;
+#endif
+ writel(tmp, SG_MEMCONF);
+
+ /* Input ports must be enabled deasserting reset of cores */
+ tmp = readl(SG_IECTRL);
+ tmp |= 0x1;
+ writel(tmp, SG_IECTRL);
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/umc-regs.h>
+
+static inline void umc_start_ssif(void __iomem *ssif_base)
+{
+ writel(0x00000001, ssif_base + 0x0000b004);
+ writel(0xffffffff, ssif_base + 0x0000c004);
+ writel(0x07ffffff, ssif_base + 0x0000c008);
+ writel(0x00000001, ssif_base + 0x0000b000);
+ writel(0x00000001, ssif_base + 0x0000c000);
+
+ writel(0x03010100, ssif_base + UMC_HDMCHSEL);
+ writel(0x03010101, ssif_base + UMC_MDMCHSEL);
+ writel(0x03010100, ssif_base + UMC_DVCCHSEL);
+ writel(0x03010100, ssif_base + UMC_DMDCHSEL);
+
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_FETCH);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMQUE0);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMWC0);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMRC0);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMQUE1);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMWC1);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMRC1);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_WC);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_RC);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_DST);
+ writel(0x00000000, ssif_base + 0x0000c044); /* DCGIV_SSIF_REG */
+
+ writel(0x00000001, ssif_base + UMC_CPURST);
+ writel(0x00000001, ssif_base + UMC_IDSRST);
+ writel(0x00000001, ssif_base + UMC_IXMRST);
+ writel(0x00000001, ssif_base + UMC_HDMRST);
+ writel(0x00000001, ssif_base + UMC_MDMRST);
+ writel(0x00000001, ssif_base + UMC_HDDRST);
+ writel(0x00000001, ssif_base + UMC_MDDRST);
+ writel(0x00000001, ssif_base + UMC_SIORST);
+ writel(0x00000001, ssif_base + UMC_GIORST);
+ writel(0x00000001, ssif_base + UMC_HD2RST);
+ writel(0x00000001, ssif_base + UMC_VIORST);
+ writel(0x00000001, ssif_base + UMC_DVCRST);
+ writel(0x00000001, ssif_base + UMC_RGLRST);
+ writel(0x00000001, ssif_base + UMC_VPERST);
+ writel(0x00000001, ssif_base + UMC_AIORST);
+ writel(0x00000001, ssif_base + UMC_DMDRST);
+}
+
+void umc_dramcont_init(void __iomem *dramcont, void __iomem *ca_base,
+ int size, int freq)
+{
+ writel(0x66bb0f17, dramcont + UMC_CMDCTLA);
+ writel(0x18c6aa44, dramcont + UMC_CMDCTLB);
+ writel(0x5101387f, dramcont + UMC_INITCTLA);
+ writel(0x43030d3f, dramcont + UMC_INITCTLB);
+ writel(0x00ff00ff, dramcont + UMC_INITCTLC);
+ writel(0x00000d71, dramcont + UMC_DRMMR0);
+ writel(0x00000006, dramcont + UMC_DRMMR1);
+ writel(0x00000298, dramcont + UMC_DRMMR2);
+ writel(0x00000000, dramcont + UMC_DRMMR3);
+ writel(0x003f0617, dramcont + UMC_SPCCTLA);
+ writel(0x00ff0008, dramcont + UMC_SPCCTLB);
+ writel(0x000c00ae, dramcont + UMC_RDATACTL_D0);
+ writel(0x000c00ae, dramcont + UMC_RDATACTL_D1);
+ writel(0x04060802, dramcont + UMC_WDATACTL_D0);
+ writel(0x04060802, dramcont + UMC_WDATACTL_D1);
+ writel(0x04a02000, dramcont + UMC_DATASET);
+ writel(0x00000000, ca_base + 0x2300);
+ writel(0x00400020, dramcont + UMC_DCCGCTL);
+ writel(0x0000000f, dramcont + 0x7000);
+ writel(0x0000000f, dramcont + 0x8000);
+ writel(0x000000c3, dramcont + 0x8004);
+ writel(0x00000071, dramcont + 0x8008);
+ writel(0x00000004, dramcont + UMC_FLOWCTLG);
+ writel(0x00000000, dramcont + 0x0060);
+ writel(0x80000201, ca_base + 0xc20);
+ writel(0x0801e01e, dramcont + UMC_FLOWCTLA);
+ writel(0x00200000, dramcont + UMC_FLOWCTLB);
+ writel(0x00004444, dramcont + UMC_FLOWCTLC);
+ writel(0x200a0a00, dramcont + UMC_SPCSETB);
+ writel(0x00010000, dramcont + UMC_SPCSETD);
+ writel(0x80000020, dramcont + UMC_DFICUPDCTLA);
+}
+
+static inline int umc_init_sub(int freq, int size_ch0, int size_ch1)
+{
+ void __iomem *ssif_base = (void __iomem *)UMC_SSIF_BASE;
+ void __iomem *ca_base0 = (void __iomem *)UMC_CA_BASE(0);
+ void __iomem *ca_base1 = (void __iomem *)UMC_CA_BASE(1);
+ void __iomem *dramcont0 = (void __iomem *)UMC_DRAMCONT_BASE(0);
+ void __iomem *dramcont1 = (void __iomem *)UMC_DRAMCONT_BASE(1);
+
+ umc_dram_init_start(dramcont0);
+ umc_dram_init_start(dramcont1);
+ umc_dram_init_poll(dramcont0);
+ umc_dram_init_poll(dramcont1);
+
+ writel(0x00000101, dramcont0 + UMC_DIOCTLA);
+
+ writel(0x00000103, dramcont0 + UMC_DIOCTLA);
+
+ writel(0x00000101, dramcont1 + UMC_DIOCTLA);
+
+ writel(0x00000103, dramcont1 + UMC_DIOCTLA);
+
+ umc_dramcont_init(dramcont0, ca_base0, size_ch0, freq);
+ umc_dramcont_init(dramcont1, ca_base1, size_ch1, freq);
+
+ umc_start_ssif(ssif_base);
+
+ return 0;
+}
+
+int umc_init(void)
+{
+ return umc_init_sub(CONFIG_DDR_FREQ, CONFIG_SDRAM0_SIZE / 0x08000000,
+ CONFIG_SDRAM1_SIZE / 0x08000000);
+}
+
+#if CONFIG_DDR_FREQ != 1600
+#error Unsupported DDR frequency.
+#endif
+
+#if ((CONFIG_SDRAM0_SIZE == 0x20000000 && CONFIG_DDR_NUM_CH0 == 2) || \
+ (CONFIG_SDRAM0_SIZE == 0x10000000 && CONFIG_DDR_NUM_CH0 == 1)) && \
+ ((CONFIG_SDRAM1_SIZE == 0x20000000 && CONFIG_DDR_NUM_CH1 == 2) || \
+ (CONFIG_SDRAM1_SIZE == 0x10000000 && CONFIG_DDR_NUM_CH1 == 1))
+/* OK */
+#else
+ #error Unsupported DDR configuration.
+#endif
--- /dev/null
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-$(CONFIG_DISPLAY_BOARDINFO) += board_info.o
+obj-y += boot-mode.o
+obj-$(CONFIG_BOARD_POSTCLK_INIT) += board_postclk_init.o bcu_init.o \
+ sbc_init.o sg_init.o pll_init.o clkrst_init.o pinctrl.o
+obj-$(CONFIG_SPL_BUILD) += pll_spectrum.o \
+ umc_init.o
--- /dev/null
+#include "../ph1-ld4/bcu_init.c"
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/board.h>
+
+int checkboard(void)
+{
+ puts("Board: PH1-sLD8 Board\n");
+
+ return check_support_card();
+}
--- /dev/null
+#include "../ph1-ld4/board_postclk_init.c"
--- /dev/null
+#include "../ph1-pro4/boot-mode.c"
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sc-regs.h>
+
+void clkrst_init(void)
+{
+ u32 tmp;
+
+ /* deassert reset */
+ tmp = readl(SC_RSTCTRL);
+ tmp |= SC_RSTCTRL_NRST_ETHER | SC_RSTCTRL_NRST_UMC1
+ | SC_RSTCTRL_NRST_UMC0 | SC_RSTCTRL_NRST_NAND;
+ writel(tmp, SC_RSTCTRL);
+ readl(SC_RSTCTRL); /* dummy read */
+
+ /* privide clocks */
+ tmp = readl(SC_CLKCTRL);
+ tmp |= SC_CLKCTRL_CLK_ETHER | SC_CLKCTRL_CLK_MIO | SC_CLKCTRL_CLK_UMC
+ | SC_CLKCTRL_CLK_NAND | SC_CLKCTRL_CLK_SBC | SC_CLKCTRL_CLK_PERI;
+ writel(tmp, SC_CLKCTRL);
+ readl(SC_CLKCTRL); /* dummy read */
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sg-regs.h>
+
+void pin_init(void)
+{
+ /* Comment format: PAD Name -> Function Name */
+
+#ifdef CONFIG_UNIPHIER_SERIAL
+ sg_set_pinsel(70, 3); /* HDDOUT0 -> TXD0 */
+ sg_set_pinsel(71, 3); /* HSDOUT1 -> RXD0 */
+
+ sg_set_pinsel(114, 0); /* TXD1 -> TXD1 */
+ sg_set_pinsel(115, 0); /* RXD1 -> RXD1 */
+
+ sg_set_pinsel(112, 1); /* SBO1 -> TXD2 */
+ sg_set_pinsel(113, 1); /* SBI1 -> RXD2 */
+
+ sg_set_pinsel(110, 1); /* SBO0 -> TXD3 */
+ sg_set_pinsel(111, 1); /* SBI0 -> RXD3 */
+#endif
+
+#ifdef CONFIG_NAND_DENALI
+ sg_set_pinsel(15, 0); /* XNFRE_GB -> XNFRE_GB */
+ sg_set_pinsel(16, 0); /* XNFWE_GB -> XNFWE_GB */
+ sg_set_pinsel(17, 0); /* XFALE_GB -> NFALE_GB */
+ sg_set_pinsel(18, 0); /* XFCLE_GB -> NFCLE_GB */
+ sg_set_pinsel(19, 0); /* XNFWP_GB -> XFNWP_GB */
+ sg_set_pinsel(20, 0); /* XNFCE0_GB -> XNFCE0_GB */
+ sg_set_pinsel(21, 0); /* NANDRYBY0_GB -> NANDRYBY0_GB */
+ sg_set_pinsel(22, 0); /* XFNCE1_GB -> XFNCE1_GB */
+ sg_set_pinsel(23, 0); /* NANDRYBY1_GB -> NANDRYBY1_GB */
+ sg_set_pinsel(24, 0); /* NFD0_GB -> NFD0_GB */
+ sg_set_pinsel(25, 0); /* NFD1_GB -> NFD1_GB */
+ sg_set_pinsel(26, 0); /* NFD2_GB -> NFD2_GB */
+ sg_set_pinsel(27, 0); /* NFD3_GB -> NFD3_GB */
+ sg_set_pinsel(28, 0); /* NFD4_GB -> NFD4_GB */
+ sg_set_pinsel(29, 0); /* NFD5_GB -> NFD5_GB */
+ sg_set_pinsel(30, 0); /* NFD6_GB -> NFD6_GB */
+ sg_set_pinsel(31, 0); /* NFD7_GB -> NFD7_GB */
+#endif
+
+#ifdef CONFIG_USB_EHCI_UNIPHIER
+ sg_set_pinsel(41, 0); /* USB0VBUS -> USB0VBUS */
+ sg_set_pinsel(42, 0); /* USB0OD -> USB0OD */
+ sg_set_pinsel(43, 0); /* USB1VBUS -> USB1VBUS */
+ sg_set_pinsel(44, 0); /* USB1OD -> USB1OD */
+ /* sg_set_pinsel(114, 4); */ /* TXD1 -> USB2VBUS (shared with UART) */
+ /* sg_set_pinsel(115, 4); */ /* RXD1 -> USB2OD */
+#endif
+}
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sc-regs.h>
+#include <asm/arch/sg-regs.h>
+
+void dpll_init(void)
+{
+ u32 tmp;
+ /*
+ * Set DPLL SSC parameters for DPLLCTRL3
+ * [23] DIVN_TEST 0x1
+ * [22:16] DIVN 0x50
+ * [10] FREFSEL_TEST 0x1
+ * [9:8] FREFSEL 0x2
+ * [4] ICPD_TEST 0x1
+ * [3:0] ICPD 0xb
+ */
+ tmp = readl(SC_DPLLCTRL3);
+ tmp &= ~0x00ff0717;
+ tmp |= 0x00d0061b;
+ writel(tmp, SC_DPLLCTRL3);
+
+ /*
+ * Set DPLL SSC parameters for DPLLCTRL
+ * <-1%> <-2%>
+ * [29:20] SSC_UPCNT 132 (0x084) 132 (0x084)
+ * [14:0] SSC_dK 6335(0x18bf) 12710(0x31a6)
+ */
+ tmp = readl(SC_DPLLCTRL);
+ tmp &= ~0x3ff07fff;
+#ifdef CONFIG_DPLL_SSC_RATE_1PER
+ tmp |= 0x084018bf;
+#else
+ tmp |= 0x084031a6;
+#endif
+ writel(tmp, SC_DPLLCTRL);
+
+ /*
+ * Set DPLL SSC parameters for DPLLCTRL2
+ * [31:29] SSC_STEP 0
+ * [27] SSC_REG_REF 1
+ * [26:20] SSC_M 79 (0x4f)
+ * [19:0] SSC_K 964689 (0xeb851)
+ */
+ tmp = readl(SC_DPLLCTRL2);
+ tmp &= ~0xefffffff;
+ tmp |= 0x0cfeb851;
+ writel(tmp, SC_DPLLCTRL2);
+}
+
+void upll_init(void)
+{
+ u32 tmp, clk_mode_upll, clk_mode_axosel;
+
+ tmp = readl(SG_PINMON0);
+ clk_mode_upll = tmp & SG_PINMON0_CLK_MODE_UPLLSRC_MASK;
+ clk_mode_axosel = tmp & SG_PINMON0_CLK_MODE_AXOSEL_MASK;
+
+ /* set 0 to SNRT(UPLLCTRL.bit28) and K_LD(UPLLCTRL.bit[27]) */
+ tmp = readl(SC_UPLLCTRL);
+ tmp &= ~0x18000000;
+ writel(tmp, SC_UPLLCTRL);
+
+ if (clk_mode_upll == SG_PINMON0_CLK_MODE_UPLLSRC_DEFAULT) {
+ if (clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_U ||
+ clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_A) {
+ /* AXO: 25MHz */
+ tmp &= ~0x07ffffff;
+ tmp |= 0x0228f5c0;
+ } else {
+ /* AXO: default 24.576MHz */
+ tmp &= ~0x07ffffff;
+ tmp |= 0x02328000;
+ }
+ }
+
+ writel(tmp, SC_UPLLCTRL);
+
+ /* set 1 to K_LD(UPLLCTRL.bit[27]) */
+ tmp |= 0x08000000;
+ writel(tmp, SC_UPLLCTRL);
+
+ /* wait 10 usec */
+ udelay(10);
+
+ /* set 1 to SNRT(UPLLCTRL.bit[28]) */
+ tmp |= 0x10000000;
+ writel(tmp, SC_UPLLCTRL);
+}
+
+void vpll_init(void)
+{
+ u32 tmp, clk_mode_axosel;
+
+ tmp = readl(SG_PINMON0);
+ clk_mode_axosel = tmp & SG_PINMON0_CLK_MODE_AXOSEL_MASK;
+
+ /* set 1 to VPLA27WP and VPLA27WP */
+ tmp = readl(SC_VPLL27ACTRL);
+ tmp |= 0x00000001;
+ writel(tmp, SC_VPLL27ACTRL);
+ tmp = readl(SC_VPLL27BCTRL);
+ tmp |= 0x00000001;
+ writel(tmp, SC_VPLL27BCTRL);
+
+ /* Set 0 to VPLA_K_LD and VPLB_K_LD */
+ tmp = readl(SC_VPLL27ACTRL3);
+ tmp &= ~0x10000000;
+ writel(tmp, SC_VPLL27ACTRL3);
+ tmp = readl(SC_VPLL27BCTRL3);
+ tmp &= ~0x10000000;
+ writel(tmp, SC_VPLL27BCTRL3);
+
+ /* Set 0 to VPLA_SNRST and VPLB_SNRST */
+ tmp = readl(SC_VPLL27ACTRL2);
+ tmp &= ~0x10000000;
+ writel(tmp, SC_VPLL27ACTRL2);
+ tmp = readl(SC_VPLL27BCTRL2);
+ tmp &= ~0x10000000;
+ writel(tmp, SC_VPLL27BCTRL2);
+
+ /* Set 0x20 to VPLA_SNRST and VPLB_SNRST */
+ tmp = readl(SC_VPLL27ACTRL2);
+ tmp &= ~0x0000007f;
+ tmp |= 0x00000020;
+ writel(tmp, SC_VPLL27ACTRL2);
+ tmp = readl(SC_VPLL27BCTRL2);
+ tmp &= ~0x0000007f;
+ tmp |= 0x00000020;
+ writel(tmp, SC_VPLL27BCTRL2);
+
+ if (clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_U ||
+ clk_mode_axosel == SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_A) {
+ /* AXO: 25MHz */
+ tmp = readl(SC_VPLL27ACTRL3);
+ tmp &= ~0x000fffff;
+ tmp |= 0x00066664;
+ writel(tmp, SC_VPLL27ACTRL3);
+ tmp = readl(SC_VPLL27BCTRL3);
+ tmp &= ~0x000fffff;
+ tmp |= 0x00066664;
+ writel(tmp, SC_VPLL27BCTRL3);
+ } else {
+ /* AXO: default 24.576MHz */
+ tmp = readl(SC_VPLL27ACTRL3);
+ tmp &= ~0x000fffff;
+ tmp |= 0x000f5800;
+ writel(tmp, SC_VPLL27ACTRL3);
+ tmp = readl(SC_VPLL27BCTRL3);
+ tmp &= ~0x000fffff;
+ tmp |= 0x000f5800;
+ writel(tmp, SC_VPLL27BCTRL3);
+ }
+
+ /* Set 1 to VPLA_K_LD and VPLB_K_LD */
+ tmp = readl(SC_VPLL27ACTRL3);
+ tmp |= 0x10000000;
+ writel(tmp, SC_VPLL27ACTRL3);
+ tmp = readl(SC_VPLL27BCTRL3);
+ tmp |= 0x10000000;
+ writel(tmp, SC_VPLL27BCTRL3);
+
+ /* wait 10 usec */
+ udelay(10);
+
+ /* Set 0 to VPLA_SNRST and VPLB_SNRST */
+ tmp = readl(SC_VPLL27ACTRL2);
+ tmp |= 0x10000000;
+ writel(tmp, SC_VPLL27ACTRL2);
+ tmp = readl(SC_VPLL27BCTRL2);
+ tmp |= 0x10000000;
+ writel(tmp, SC_VPLL27BCTRL2);
+
+ /* set 0 to VPLA27WP and VPLA27WP */
+ tmp = readl(SC_VPLL27ACTRL);
+ tmp &= ~0x00000001;
+ writel(tmp, SC_VPLL27ACTRL);
+ tmp = readl(SC_VPLL27BCTRL);
+ tmp |= ~0x00000001;
+ writel(tmp, SC_VPLL27BCTRL);
+}
+
+void pll_init(void)
+{
+ dpll_init();
+ upll_init();
+ vpll_init();
+
+ /*
+ * Wait 500 usec until dpll get stable
+ * We wait 10 usec in upll_init() and vpll_init()
+ * so 20 usec can be saved here.
+ */
+ udelay(480);
+}
--- /dev/null
+#include "../ph1-ld4/pll_spectrum.c"
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sbc-regs.h>
+#include <asm/arch/sg-regs.h>
+
+void sbc_init(void)
+{
+#if !defined(CONFIG_SPL_BUILD)
+ /* XECS0 : dummy */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL00);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL01);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL02);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL04);
+#endif
+ /* XECS1 : boot memory (always boot swap = on) */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL10);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL11);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL12);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL14);
+
+ /* XECS4 : sub memory */
+ writel(SBCTRL0_SAVEPIN_MEM_VALUE, SBCTRL40);
+ writel(SBCTRL1_SAVEPIN_MEM_VALUE, SBCTRL41);
+ writel(SBCTRL2_SAVEPIN_MEM_VALUE, SBCTRL42);
+ writel(SBCTRL4_SAVEPIN_MEM_VALUE, SBCTRL44);
+
+ /* XECS5 : peripherals */
+ writel(SBCTRL0_SAVEPIN_PERI_VALUE, SBCTRL50);
+ writel(SBCTRL1_SAVEPIN_PERI_VALUE, SBCTRL51);
+ writel(SBCTRL2_SAVEPIN_PERI_VALUE, SBCTRL52);
+ writel(SBCTRL4_SAVEPIN_PERI_VALUE, SBCTRL54);
+
+ /* base address regsiters */
+ writel(0x0000bc01, SBBASE0); /* boot memory */
+ writel(0x0900bfff, SBBASE1); /* dummy */
+ writel(0x0400bc01, SBBASE4); /* sub memory */
+ writel(0x0800bf01, SBBASE5); /* peripherals */
+
+ sg_set_pinsel(134, 16); /* XIRQ6 -> XECS4 */
+ sg_set_pinsel(135, 16); /* XIRQ7 -> XECS5 */
+
+ /* dummy read to assure write process */
+ readl(SG_PINCTRL(33));
+}
--- /dev/null
+#include "../ph1-ld4/sg_init.c"
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/umc-regs.h>
+
+static inline void umc_start_ssif(void __iomem *ssif_base)
+{
+ writel(0x00000000, ssif_base + 0x0000b004);
+ writel(0xffffffff, ssif_base + 0x0000c004);
+ writel(0x000fffcf, ssif_base + 0x0000c008);
+ writel(0x00000001, ssif_base + 0x0000b000);
+ writel(0x00000001, ssif_base + 0x0000c000);
+ writel(0x03010101, ssif_base + UMC_MDMCHSEL);
+ writel(0x03010100, ssif_base + UMC_DMDCHSEL);
+
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_FETCH);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMQUE0);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMWC0);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMRC0);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMQUE1);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMWC1);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_COMRC1);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_WC);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_RC);
+ writel(0x00000000, ssif_base + UMC_CLKEN_SSIF_DST);
+
+ writel(0x00000001, ssif_base + UMC_CPURST);
+ writel(0x00000001, ssif_base + UMC_IDSRST);
+ writel(0x00000001, ssif_base + UMC_IXMRST);
+ writel(0x00000001, ssif_base + UMC_MDMRST);
+ writel(0x00000001, ssif_base + UMC_MDDRST);
+ writel(0x00000001, ssif_base + UMC_SIORST);
+ writel(0x00000001, ssif_base + UMC_VIORST);
+ writel(0x00000001, ssif_base + UMC_FRCRST);
+ writel(0x00000001, ssif_base + UMC_RGLRST);
+ writel(0x00000001, ssif_base + UMC_AIORST);
+ writel(0x00000001, ssif_base + UMC_DMDRST);
+}
+
+void umc_dramcont_init(void __iomem *dramcont, void __iomem *ca_base,
+ int size, int freq)
+{
+#ifdef CONFIG_DDR_STANDARD
+ writel(0x55990b11, dramcont + UMC_CMDCTLA);
+ writel(0x16958944, dramcont + UMC_CMDCTLB);
+#else
+ writel(0x45990b11, dramcont + UMC_CMDCTLA);
+ writel(0x16958924, dramcont + UMC_CMDCTLB);
+#endif
+
+ writel(0x5101046A, dramcont + UMC_INITCTLA);
+
+ if (size == 1)
+ writel(0x27028B0A, dramcont + UMC_INITCTLB);
+ else if (size == 2)
+ writel(0x38028B0A, dramcont + UMC_INITCTLB);
+
+ writel(0x00FF00FF, dramcont + UMC_INITCTLC);
+ writel(0x00000b51, dramcont + UMC_DRMMR0);
+ writel(0x00000006, dramcont + UMC_DRMMR1);
+ writel(0x00000290, dramcont + UMC_DRMMR2);
+
+#ifdef CONFIG_DDR_STANDARD
+ writel(0x00000000, dramcont + UMC_DRMMR3);
+#else
+ writel(0x00000800, dramcont + UMC_DRMMR3);
+#endif
+
+ if (size == 1)
+ writel(0x00240512, dramcont + UMC_SPCCTLA);
+ else if (size == 2)
+ writel(0x00350512, dramcont + UMC_SPCCTLA);
+
+ writel(0x00ff0006, dramcont + UMC_SPCCTLB);
+ writel(0x000a00ac, dramcont + UMC_RDATACTL_D0);
+ writel(0x04060806, dramcont + UMC_WDATACTL_D0);
+ writel(0x04a02000, dramcont + UMC_DATASET);
+ writel(0x00000000, ca_base + 0x2300);
+ writel(0x00400020, dramcont + UMC_DCCGCTL);
+ writel(0x00000003, dramcont + 0x7000);
+ writel(0x0000004f, dramcont + 0x8000);
+ writel(0x000000c3, dramcont + 0x8004);
+ writel(0x00000077, dramcont + 0x8008);
+ writel(0x0000003b, dramcont + UMC_DICGCTLA);
+ writel(0x020a0808, dramcont + UMC_DICGCTLB);
+ writel(0x00000004, dramcont + UMC_FLOWCTLG);
+ writel(0x80000201, ca_base + 0xc20);
+ writel(0x0801e01e, dramcont + UMC_FLOWCTLA);
+ writel(0x00200000, dramcont + UMC_FLOWCTLB);
+ writel(0x00004444, dramcont + UMC_FLOWCTLC);
+ writel(0x200a0a00, dramcont + UMC_SPCSETB);
+ writel(0x00000000, dramcont + UMC_SPCSETD);
+ writel(0x00000520, dramcont + UMC_DFICUPDCTLA);
+}
+
+static inline int umc_init_sub(int freq, int size_ch0, int size_ch1)
+{
+ void __iomem *ssif_base = (void __iomem *)UMC_SSIF_BASE;
+ void __iomem *ca_base0 = (void __iomem *)UMC_CA_BASE(0);
+ void __iomem *ca_base1 = (void __iomem *)UMC_CA_BASE(1);
+ void __iomem *dramcont0 = (void __iomem *)UMC_DRAMCONT_BASE(0);
+ void __iomem *dramcont1 = (void __iomem *)UMC_DRAMCONT_BASE(1);
+
+ umc_dram_init_start(dramcont0);
+ umc_dram_init_start(dramcont1);
+ umc_dram_init_poll(dramcont0);
+ umc_dram_init_poll(dramcont1);
+
+ writel(0x00000101, dramcont0 + UMC_DIOCTLA);
+
+ writel(0x00000101, dramcont1 + UMC_DIOCTLA);
+
+ umc_dramcont_init(dramcont0, ca_base0, size_ch0, freq);
+ umc_dramcont_init(dramcont1, ca_base1, size_ch1, freq);
+
+ umc_start_ssif(ssif_base);
+
+ return 0;
+}
+
+int umc_init(void)
+{
+ return umc_init_sub(CONFIG_DDR_FREQ, CONFIG_SDRAM0_SIZE / 0x08000000,
+ CONFIG_SDRAM1_SIZE / 0x08000000);
+}
+
+#if CONFIG_DDR_FREQ != 1333
+#error Unsupported DDR frequency.
+#endif
+
+#if (CONFIG_SDRAM0_SIZE == 0x08000000 || CONFIG_SDRAM0_SIZE == 0x10000000) && \
+ (CONFIG_SDRAM1_SIZE == 0x08000000 || CONFIG_SDRAM1_SIZE == 0x10000000) && \
+ CONFIG_DDR_NUM_CH0 == 1 && CONFIG_DDR_NUM_CH1 == 1
+/* OK */
+#else
+#error Unsupported DDR configuration.
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sc-regs.h>
+#include <asm/arch/board.h>
+
+void reset_cpu(unsigned long ignored)
+{
+ u32 tmp;
+
+ uniphier_board_reset();
+
+ writel(5, SC_IRQTIMSET); /* default value */
+
+ tmp = readl(SC_SLFRSTSEL);
+ tmp &= ~0x3; /* mask [1:0] */
+ tmp |= 0x0; /* XRST reboot */
+ writel(tmp, SC_SLFRSTSEL);
+
+ tmp = readl(SC_SLFRSTCTL);
+ tmp |= 0x1;
+ writel(tmp, SC_SLFRSTCTL);
+}
--- /dev/null
+/*
+ * Copyright (C) 2013 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <config.h>
+#include <linux/linkage.h>
+#include <asm/system.h>
+#include <asm/arch/led.h>
+#include <asm/arch/sbc-regs.h>
+
+/* Entry point of U-Boot main program for the secondary CPU */
+LENTRY(secondary_entry)
+ mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
+ bic r0, r0, #(CR_C | CR_M) @ MMU and Dcache disable
+ mcr p15, 0, r0, c1, c0, 0
+ mcr p15, 0, r0, c8, c7, 0 @ invalidate TLBs
+ mcr p15, 0, r0, c7, c5, 0 @ invalidate icache
+ dsb
+ led_write(C,0,,)
+ ldr r1, =ROM_BOOT_ROMRSV2
+ mov r0, #0
+ str r0, [r1]
+0: wfe
+ ldr r4, [r1] @ r4: entry point for secondary CPUs
+ cmp r4, #0
+ beq 0b
+ led_write(C, P, U, 1)
+ bx r4 @ secondary CPUs jump to linux
+ENDPROC(secondary_entry)
+
+ENTRY(wakeup_secondary)
+ ldr r1, =ROM_BOOT_ROMRSV2
+0: ldr r0, [r1]
+ cmp r0, #0
+ bne 0b
+
+ /* set entry address and send event to the secondary CPU */
+ ldr r0, =secondary_entry
+ str r0, [r1]
+ ldr r0, [r1] @ make sure store is complete
+ mov r0, #0x100
+0: subs r0, r0, #1 @ I don't know the reason, but without this wait
+ bne 0b @ fails to wake up the secondary CPU
+ sev
+
+ /* wait until the secondary CPU reach to secondary_entry */
+0: ldr r0, [r1]
+ cmp r0, #0
+ bne 0b
+ bx lr
+ENDPROC(wakeup_secondary)
--- /dev/null
+/*
+ * Copyright (C) 2013-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+
+void spl_board_init(void)
+{
+#if defined(CONFIG_BOARD_POSTCLK_INIT)
+ board_postclk_init();
+#endif
+ dram_init();
+}
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/board.h>
+
+#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
+
+#define PFC_MICRO_SUPPORT_CARD_RESET \
+ ((CONFIG_SUPPORT_CARD_BASE) + 0x000D0034)
+#define PFC_MICRO_SUPPORT_CARD_REVISION \
+ ((CONFIG_SUPPORT_CARD_BASE) + 0x000D00E0)
+/*
+ * 0: reset deassert, 1: reset
+ *
+ * bit[0]: LAN, I2C, LED
+ * bit[1]: UART
+ */
+void support_card_reset_deassert(void)
+{
+ writel(0, PFC_MICRO_SUPPORT_CARD_RESET);
+}
+
+void support_card_reset(void)
+{
+ writel(3, PFC_MICRO_SUPPORT_CARD_RESET);
+}
+
+static int support_card_show_revision(void)
+{
+ u32 revision;
+
+ revision = readl(PFC_MICRO_SUPPORT_CARD_REVISION);
+ printf("(PFC CPLD version %d.%d)\n", revision >> 4, revision & 0xf);
+ return 0;
+}
+#endif
+
+#if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
+
+#define DCC_MICRO_SUPPORT_CARD_RESET_LAN \
+ ((CONFIG_SUPPORT_CARD_BASE) + 0x00401300)
+#define DCC_MICRO_SUPPORT_CARD_RESET_UART \
+ ((CONFIG_SUPPORT_CARD_BASE) + 0x00401304)
+#define DCC_MICRO_SUPPORT_CARD_RESET_I2C \
+ ((CONFIG_SUPPORT_CARD_BASE) + 0x00401308)
+#define DCC_MICRO_SUPPORT_CARD_REVISION \
+ ((CONFIG_SUPPORT_CARD_BASE) + 0x005000E0)
+
+void support_card_reset_deassert(void)
+{
+ writel(1, DCC_MICRO_SUPPORT_CARD_RESET_LAN); /* LAN and LED */
+ writel(1, DCC_MICRO_SUPPORT_CARD_RESET_UART); /* UART */
+ writel(1, DCC_MICRO_SUPPORT_CARD_RESET_I2C); /* I2C */
+}
+
+void support_card_reset(void)
+{
+ writel(0, DCC_MICRO_SUPPORT_CARD_RESET_LAN); /* LAN and LED */
+ writel(0, DCC_MICRO_SUPPORT_CARD_RESET_UART); /* UART */
+ writel(0, DCC_MICRO_SUPPORT_CARD_RESET_I2C); /* I2C */
+}
+
+static int support_card_show_revision(void)
+{
+ u32 revision;
+
+ revision = readl(DCC_MICRO_SUPPORT_CARD_REVISION);
+
+ if (revision >= 0x67) {
+ printf("(DCC CPLD version 3.%d.%d)\n",
+ revision >> 4, revision & 0xf);
+ return 0;
+ } else {
+ printf("(DCC CPLD unknown version)\n");
+ return -1;
+ }
+}
+#endif
+
+void support_card_init(void)
+{
+ /*
+ * After power on, we need to keep the LAN controller in reset state
+ * for a while. (200 usec)
+ * Fortunatelly, enough wait time is already inserted in pll_init()
+ * function. So we do not have to wait here.
+ */
+ support_card_reset_deassert();
+}
+
+int check_support_card(void)
+{
+ printf("SC: Micro Support Card ");
+ return support_card_show_revision();
+}
+
+#if defined(CONFIG_SMC911X)
+#include <netdev.h>
+
+int board_eth_init(bd_t *bis)
+{
+ return smc911x_initialize(0, CONFIG_SMC911X_BASE);
+}
+#endif
+
+#if !defined(CONFIG_SYS_NO_FLASH)
+
+#include <mtd/cfi_flash.h>
+
+#if CONFIG_SYS_MAX_FLASH_BANKS > 1
+static phys_addr_t flash_banks_list[CONFIG_SYS_MAX_FLASH_BANKS] =
+ CONFIG_SYS_FLASH_BANKS_LIST;
+
+phys_addr_t cfi_flash_bank_addr(int i)
+{
+ return flash_banks_list[i];
+}
+#endif
+
+int mem_is_flash(phys_addr_t base)
+{
+ const int loop = 128;
+ u32 *scratch_addr;
+ u32 saved_value;
+ int ret = 1;
+ int i;
+
+ scratch_addr = map_physmem(base + 0x01e00000,
+ sizeof(u32) * loop, MAP_NOCACHE);
+
+ for (i = 0; i < loop; i++, scratch_addr++) {
+ saved_value = readl(scratch_addr);
+ writel(~saved_value, scratch_addr);
+ if (readl(scratch_addr) != saved_value) {
+ /* We assume no memory or SRAM here. */
+ writel(saved_value, scratch_addr);
+ ret = 0;
+ break;
+ }
+ }
+
+ unmap_physmem(scratch_addr, MAP_NOCACHE);
+
+ return ret;
+}
+
+int board_flash_wp_on(void)
+{
+ int i;
+ int ret = 1;
+
+ for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
+ if (mem_is_flash(cfi_flash_bank_addr(i))) {
+ /*
+ * We found at least one flash.
+ * We need to return 0 and call flash_init().
+ */
+ ret = 0;
+ }
+#if CONFIG_SYS_MAX_FLASH_BANKS > 1
+ else {
+ /*
+ * We might have a SRAM here.
+ * To prevent SRAM data from being destroyed,
+ * we set dummy address (SDRAM).
+ */
+ flash_banks_list[i] = 0x80000000 + 0x10000 * i;
+ }
+#endif
+ }
+
+ return ret;
+}
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/arm-mpcore.h>
+
+#define PERIPHCLK (50 * 1000 * 1000) /* 50 MHz */
+#define PRESCALER ((PERIPHCLK) / (CONFIG_SYS_TIMER_RATE) - 1)
+
+static void *get_global_timer_base(void)
+{
+ void *val;
+
+ asm("mrc p15, 4, %0, c15, c0, 0" : "=r" (val) : : "memory");
+
+ return val + GLOBAL_TIMER_OFFSET;
+}
+
+unsigned long timer_read_counter(void)
+{
+ /*
+ * ARM 64bit Global Timer is too much for our purpose.
+ * We use only lower 32 bit of the timer counter.
+ */
+ return readl(get_global_timer_base() + GTIMER_CNT_L);
+}
+
+int timer_init(void)
+{
+ /* enable timer */
+ writel(PRESCALER << 8 | 1, get_global_timer_base() + GTIMER_CTRL);
+
+ return 0;
+}
--- /dev/null
+if ARM64
+
+config SYS_CPU
+ default "armv8"
+
+endif
obj-y += cpu.o
obj-y += lowlevel.o
obj-y += speed.o
+obj-$(CONFIG_MP) += mp.o
+obj-$(CONFIG_OF_LIBFDT) += fdt.o
#include <asm/io.h>
#include <asm/arch-fsl-lsch3/immap_lsch3.h>
#include "cpu.h"
+#include "mp.h"
#include "speed.h"
#include <fsl_mc.h>
#endif
return error;
}
+
+
+int arch_early_init_r(void)
+{
+ int rv;
+ rv = fsl_lsch3_wake_seconday_cores();
+
+ if (rv)
+ printf("Did not wake secondary cores\n");
+
+ return 0;
+}
*/
int fsl_qoriq_core_to_cluster(unsigned int core);
+u32 cpu_mask(void);
--- /dev/null
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include "mp.h"
+
+#ifdef CONFIG_MP
+void ft_fixup_cpu(void *blob)
+{
+ int off;
+ __maybe_unused u64 spin_tbl_addr = (u64)get_spin_tbl_addr();
+ fdt32_t *reg;
+ int addr_cells;
+ u64 val;
+ size_t *boot_code_size = &(__secondary_boot_code_size);
+
+ off = fdt_path_offset(blob, "/cpus");
+ if (off < 0) {
+ puts("couldn't find /cpus node\n");
+ return;
+ }
+ of_bus_default_count_cells(blob, off, &addr_cells, NULL);
+
+ off = fdt_node_offset_by_prop_value(blob, -1, "device_type", "cpu", 4);
+ while (off != -FDT_ERR_NOTFOUND) {
+ reg = (fdt32_t *)fdt_getprop(blob, off, "reg", 0);
+ if (reg) {
+ val = spin_tbl_addr;
+ val += id_to_core(of_read_number(reg, addr_cells))
+ * SPIN_TABLE_ELEM_SIZE;
+ val = cpu_to_fdt64(val);
+ fdt_setprop_string(blob, off, "enable-method",
+ "spin-table");
+ fdt_setprop(blob, off, "cpu-release-addr",
+ &val, sizeof(val));
+ } else {
+ puts("Warning: found cpu node without reg property\n");
+ }
+ off = fdt_node_offset_by_prop_value(blob, off, "device_type",
+ "cpu", 4);
+ }
+
+ fdt_add_mem_rsv(blob, (uintptr_t)&secondary_boot_code,
+ *boot_code_size);
+}
+#endif
+
+void ft_cpu_setup(void *blob, bd_t *bd)
+{
+#ifdef CONFIG_MP
+ ft_fixup_cpu(blob);
+#endif
+}
#include <config.h>
#include <linux/linkage.h>
+#include <asm/gic.h>
#include <asm/macro.h>
+#include "mp.h"
ENTRY(lowlevel_init)
mov x29, lr /* Save LR */
#endif
#endif
- branch_if_master x0, x1, 1f
+ branch_if_master x0, x1, 2f
+ ldr x0, =secondary_boot_func
+ blr x0
+2:
+ mov lr, x29 /* Restore LR */
+ ret
+ENDPROC(lowlevel_init)
+
+ /* Keep literals not used by the secondary boot code outside it */
+ .ltorg
+
+ /* Using 64 bit alignment since the spin table is accessed as data */
+ .align 4
+ .global secondary_boot_code
+ /* Secondary Boot Code starts here */
+secondary_boot_code:
+ .global __spin_table
+__spin_table:
+ .space CONFIG_MAX_CPUS*SPIN_TABLE_ELEM_SIZE
+
+ .align 2
+ENTRY(secondary_boot_func)
/*
- * Slave should wait for master clearing spin table.
- * This sync prevent salves observing incorrect
- * value of spin table and jumping to wrong place.
+ * MPIDR_EL1 Fields:
+ * MPIDR[1:0] = AFF0_CPUID <- Core ID (0,1)
+ * MPIDR[7:2] = AFF0_RES
+ * MPIDR[15:8] = AFF1_CLUSTERID <- Cluster ID (0,1,2,3)
+ * MPIDR[23:16] = AFF2_CLUSTERID
+ * MPIDR[24] = MT
+ * MPIDR[29:25] = RES0
+ * MPIDR[30] = U
+ * MPIDR[31] = ME
+ * MPIDR[39:32] = AFF3
+ *
+ * Linear Processor ID (LPID) calculation from MPIDR_EL1:
+ * (We only use AFF0_CPUID and AFF1_CLUSTERID for now
+ * until AFF2_CLUSTERID and AFF3 have non-zero values)
+ *
+ * LPID = MPIDR[15:8] | MPIDR[1:0]
*/
-#if defined(CONFIG_GICV2) || defined(CONFIG_GICV3)
-#ifdef CONFIG_GICV2
- ldr x0, =GICC_BASE
-#endif
- bl gic_wait_for_interrupt
-#endif
-
+ mrs x0, mpidr_el1
+ ubfm x1, x0, #8, #15
+ ubfm x2, x0, #0, #1
+ orr x10, x2, x1, lsl #2 /* x10 has LPID */
+ ubfm x9, x0, #0, #15 /* x9 contains MPIDR[15:0] */
/*
- * All processors will enter EL2 and optionally EL1.
+ * offset of the spin table element for this core from start of spin
+ * table (each elem is padded to 64 bytes)
*/
- bl armv8_switch_to_el2
+ lsl x1, x10, #6
+ ldr x0, =__spin_table
+ /* physical address of this cpus spin table element */
+ add x11, x1, x0
+
+ str x9, [x11, #16] /* LPID */
+ mov x4, #1
+ str x4, [x11, #8] /* STATUS */
+ dsb sy
+#if defined(CONFIG_GICV3)
+ gic_wait_for_interrupt_m x0
+#elif defined(CONFIG_GICV2)
+ ldr x0, =GICC_BASE
+ gic_wait_for_interrupt_m x0, w1
+#endif
+
+ bl secondary_switch_to_el2
#ifdef CONFIG_ARMV8_SWITCH_TO_EL1
- bl armv8_switch_to_el1
+ bl secondary_switch_to_el1
#endif
- b 2f
-1:
-2:
- mov lr, x29 /* Restore LR */
- ret
-ENDPROC(lowlevel_init)
+slave_cpu:
+ wfe
+ ldr x0, [x11]
+ cbz x0, slave_cpu
+#ifndef CONFIG_ARMV8_SWITCH_TO_EL1
+ mrs x1, sctlr_el2
+#else
+ mrs x1, sctlr_el1
+#endif
+ tbz x1, #25, cpu_is_le
+ rev x0, x0 /* BE to LE conversion */
+cpu_is_le:
+ br x0 /* branch to the given address */
+ENDPROC(secondary_boot_func)
+
+ENTRY(secondary_switch_to_el2)
+ switch_el x0, 1f, 0f, 0f
+0: ret
+1: armv8_switch_to_el2_m x0
+ENDPROC(secondary_switch_to_el2)
+
+ENTRY(secondary_switch_to_el1)
+ switch_el x0, 0f, 1f, 0f
+0: ret
+1: armv8_switch_to_el1_m x0, x1
+ENDPROC(secondary_switch_to_el1)
+
+ /* Ensure that the literals used by the secondary boot code are
+ * assembled within it (this is required so that we can protect
+ * this area with a single memreserve region
+ */
+ .ltorg
+
+ /* 64 bit alignment for elements accessed as data */
+ .align 4
+ .globl __secondary_boot_code_size
+ .type __secondary_boot_code_size, %object
+ /* Secondary Boot Code ends here */
+__secondary_boot_code_size:
+ .quad .-secondary_boot_code
--- /dev/null
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/system.h>
+#include <asm/io.h>
+#include <asm/arch-fsl-lsch3/immap_lsch3.h>
+#include "mp.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void *get_spin_tbl_addr(void)
+{
+ return &__spin_table;
+}
+
+phys_addr_t determine_mp_bootpg(void)
+{
+ return (phys_addr_t)&secondary_boot_code;
+}
+
+int fsl_lsch3_wake_seconday_cores(void)
+{
+ struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+ struct ccsr_reset __iomem *rst = (void *)(CONFIG_SYS_FSL_RST_ADDR);
+ u32 cores, cpu_up_mask = 1;
+ int i, timeout = 10;
+ u64 *table = get_spin_tbl_addr();
+
+ cores = cpu_mask();
+ /* Clear spin table so that secondary processors
+ * observe the correct value after waking up from wfe.
+ */
+ memset(table, 0, CONFIG_MAX_CPUS*SPIN_TABLE_ELEM_SIZE);
+ flush_dcache_range((unsigned long)table,
+ (unsigned long)table +
+ (CONFIG_MAX_CPUS*SPIN_TABLE_ELEM_SIZE));
+
+ printf("Waking secondary cores to start from %lx\n", gd->relocaddr);
+ out_le32(&gur->bootlocptrh, (u32)(gd->relocaddr >> 32));
+ out_le32(&gur->bootlocptrl, (u32)gd->relocaddr);
+ out_le32(&gur->scratchrw[6], 1);
+ asm volatile("dsb st" : : : "memory");
+ rst->brrl = cores;
+ asm volatile("dsb st" : : : "memory");
+
+ /* This is needed as a precautionary measure.
+ * If some code before this has accidentally released the secondary
+ * cores then the pre-bootloader code will trap them in a "wfe" unless
+ * the scratchrw[6] is set. In this case we need a sev here to get these
+ * cores moving again.
+ */
+ asm volatile("sev");
+
+ while (timeout--) {
+ flush_dcache_range((unsigned long)table, (unsigned long)table +
+ CONFIG_MAX_CPUS * 64);
+ for (i = 1; i < CONFIG_MAX_CPUS; i++) {
+ if (table[i * WORDS_PER_SPIN_TABLE_ENTRY +
+ SPIN_TABLE_ELEM_STATUS_IDX])
+ cpu_up_mask |= 1 << i;
+ }
+ if (hweight32(cpu_up_mask) == hweight32(cores))
+ break;
+ udelay(10);
+ }
+ if (timeout <= 0) {
+ printf("Not all cores (0x%x) are up (0x%x)\n",
+ cores, cpu_up_mask);
+ return 1;
+ }
+ printf("All (%d) cores are up.\n", hweight32(cores));
+
+ return 0;
+}
+
+int is_core_valid(unsigned int core)
+{
+ return !!((1 << core) & cpu_mask());
+}
+
+int cpu_reset(int nr)
+{
+ puts("Feature is not implemented.\n");
+
+ return 0;
+}
+
+int cpu_disable(int nr)
+{
+ puts("Feature is not implemented.\n");
+
+ return 0;
+}
+
+int core_to_pos(int nr)
+{
+ u32 cores = cpu_mask();
+ int i, count = 0;
+
+ if (nr == 0) {
+ return 0;
+ } else if (nr >= hweight32(cores)) {
+ puts("Not a valid core number.\n");
+ return -1;
+ }
+
+ for (i = 1; i < 32; i++) {
+ if (is_core_valid(i)) {
+ count++;
+ if (count == nr)
+ break;
+ }
+ }
+
+ return count;
+}
+
+int cpu_status(int nr)
+{
+ u64 *table;
+ int pos;
+
+ if (nr == 0) {
+ table = (u64 *)get_spin_tbl_addr();
+ printf("table base @ 0x%p\n", table);
+ } else {
+ pos = core_to_pos(nr);
+ if (pos < 0)
+ return -1;
+ table = (u64 *)get_spin_tbl_addr() + pos *
+ WORDS_PER_SPIN_TABLE_ENTRY;
+ printf("table @ 0x%p\n", table);
+ printf(" addr - 0x%016llx\n",
+ table[SPIN_TABLE_ELEM_ENTRY_ADDR_IDX]);
+ printf(" status - 0x%016llx\n",
+ table[SPIN_TABLE_ELEM_STATUS_IDX]);
+ printf(" lpid - 0x%016llx\n",
+ table[SPIN_TABLE_ELEM_LPID_IDX]);
+ }
+
+ return 0;
+}
+
+int cpu_release(int nr, int argc, char * const argv[])
+{
+ u64 boot_addr;
+ u64 *table = (u64 *)get_spin_tbl_addr();
+ int pos;
+
+ pos = core_to_pos(nr);
+ if (pos <= 0)
+ return -1;
+
+ table += pos * WORDS_PER_SPIN_TABLE_ENTRY;
+ boot_addr = simple_strtoull(argv[0], NULL, 16);
+ table[SPIN_TABLE_ELEM_ENTRY_ADDR_IDX] = boot_addr;
+ flush_dcache_range((unsigned long)table,
+ (unsigned long)table + SPIN_TABLE_ELEM_SIZE);
+ asm volatile("dsb st");
+ smp_kick_all_cpus(); /* only those with entry addr set will run */
+
+ return 0;
+}
--- /dev/null
+/*
+ * Copyright 2014, Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _FSL_CH3_MP_H
+#define _FSL_CH3_MP_H
+
+/*
+* Each spin table element is defined as
+* struct {
+* uint64_t entry_addr;
+* uint64_t status;
+* uint64_t lpid;
+* };
+* we pad this struct to 64 bytes so each entry is in its own cacheline
+* the actual spin table is an array of these structures
+*/
+#define SPIN_TABLE_ELEM_ENTRY_ADDR_IDX 0
+#define SPIN_TABLE_ELEM_STATUS_IDX 1
+#define SPIN_TABLE_ELEM_LPID_IDX 2
+#define WORDS_PER_SPIN_TABLE_ENTRY 8 /* pad to 64 bytes */
+#define SPIN_TABLE_ELEM_SIZE 64
+
+#define id_to_core(x) ((x & 3) | (x >> 6))
+#ifndef __ASSEMBLY__
+extern u64 __spin_table[];
+extern u64 *secondary_boot_code;
+extern size_t __secondary_boot_code_size;
+int fsl_lsch3_wake_seconday_cores(void);
+void *get_spin_tbl_addr(void);
+phys_addr_t determine_mp_bootpg(void);
+void secondary_boot_func(void);
+#endif
+#endif /* _FSL_CH3_MP_H */
ENTRY(armv8_switch_to_el2)
switch_el x0, 1f, 0f, 0f
0: ret
-1:
- mov x0, #0x5b1 /* Non-secure EL0/EL1 | HVC | 64bit EL2 */
- msr scr_el3, x0
- msr cptr_el3, xzr /* Disable coprocessor traps to EL3 */
- mov x0, #0x33ff
- msr cptr_el2, x0 /* Disable coprocessor traps to EL2 */
-
- /* Initialize SCTLR_EL2 */
- msr sctlr_el2, xzr
-
- /* Return to the EL2_SP2 mode from EL3 */
- mov x0, sp
- msr sp_el2, x0 /* Migrate SP */
- mrs x0, vbar_el3
- msr vbar_el2, x0 /* Migrate VBAR */
- mov x0, #0x3c9
- msr spsr_el3, x0 /* EL2_SP2 | D | A | I | F */
- msr elr_el3, lr
- eret
+1: armv8_switch_to_el2_m x0
ENDPROC(armv8_switch_to_el2)
ENTRY(armv8_switch_to_el1)
switch_el x0, 0f, 1f, 0f
0: ret
-1:
- /* Initialize Generic Timers */
- mrs x0, cnthctl_el2
- orr x0, x0, #0x3 /* Enable EL1 access to timers */
- msr cnthctl_el2, x0
- msr cntvoff_el2, xzr
- mrs x0, cntkctl_el1
- orr x0, x0, #0x3 /* Enable EL0 access to timers */
- msr cntkctl_el1, x0
-
- /* Initilize MPID/MPIDR registers */
- mrs x0, midr_el1
- mrs x1, mpidr_el1
- msr vpidr_el2, x0
- msr vmpidr_el2, x1
-
- /* Disable coprocessor traps */
- mov x0, #0x33ff
- msr cptr_el2, x0 /* Disable coprocessor traps to EL2 */
- msr hstr_el2, xzr /* Disable coprocessor traps to EL2 */
- mov x0, #3 << 20
- msr cpacr_el1, x0 /* Enable FP/SIMD at EL1 */
-
- /* Initialize HCR_EL2 */
- mov x0, #(1 << 31) /* 64bit EL1 */
- orr x0, x0, #(1 << 29) /* Disable HVC */
- msr hcr_el2, x0
-
- /* SCTLR_EL1 initialization */
- mov x0, #0x0800
- movk x0, #0x30d0, lsl #16
- msr sctlr_el1, x0
-
- /* Return to the EL1_SP1 mode from EL2 */
- mov x0, sp
- msr sp_el1, x0 /* Migrate SP */
- mrs x0, vbar_el2
- msr vbar_el1, x0 /* Migrate VBAR */
- mov x0, #0x3c5
- msr spsr_el2, x0 /* EL1_SP1 | D | A | I | F */
- msr elr_el2, lr
- eret
+1: armv8_switch_to_el1_m x0, x1
ENDPROC(armv8_switch_to_el1)
exynos5250-smdk5250.dtb \
exynos5420-smdk5420.dtb \
exynos5420-peach-pit.dtb
-dtb-$(CONFIG_MX6) += imx6q-sabreauto.dtb
dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
tegra20-medcom-wide.dtb \
tegra20-paz00.dtb \
+++ /dev/null
-/*
- * Copyright 2012 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/dts-v1/;
-
-/ {
- model = "Freescale i.MX6 Quad SABRE Automotive Board";
- compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
-};
u32 reserved5[21];
u32 wpmr; /* 0xE4 Write Protect Mode Register (CAP0) */
u32 wpsr; /* 0xE8 Write Protect Status Register (CAP0) */
-#ifdef CONFIG_SAMA5D3
+#ifdef CPU_HAS_PCR
u32 reserved6[8];
u32 pcer1; /* 0x100 Periperial Clock Enable Register 1 */
u32 pcdr1; /* 0x104 Periperial Clock Disable Register 1 */
#define AT91_PMC_IXR_PCKRDY3 0x00000800
#define AT91_PMC_IXR_MOSCSELS 0x00010000
+#define AT91_PMC_PCR_PID_MASK (0x3f)
+#define AT91_PMC_PCR_CMD_WRITE (0x1 << 12)
+#define AT91_PMC_PCR_EN (0x1 << 28)
+
#define AT91_PMC_PCK (1 << 0) /* Processor Clock */
#define AT91RM9200_PMC_UDP (1 << 1) /* USB Devcice Port Clock [AT91RM9200 only] */
#define AT91RM9200_PMC_MCKUDP (1 << 2) /* USB Device Port Master Clock Automatic Disable on Suspend [AT91RM9200 only] */
int at91_clock_init(unsigned long main_clock);
void at91_periph_clk_enable(int id);
+void at91_periph_clk_disable(int id);
#endif /* __ASM_ARM_ARCH_CLK_H__ */
#define ATMEL_PIO_PORTS 5
#define CPU_HAS_PIO3
#define PIO_SCDR_DIV 0x3fff
+#define CPU_HAS_PCR
/*
* PMECC table in ROM
#define AT91_ASM_SMC_SETUP0 (ATMEL_BASE_SMC + 0x600)
#define AT91_ASM_SMC_PULSE0 (ATMEL_BASE_SMC + 0x604)
#define AT91_ASM_SMC_CYCLE0 (ATMEL_BASE_SMC + 0x608)
-#define AT91_ASM_SMC_MODE0 (ATMEL_BASE_SMC + 0x60C)
+#define AT91_ASM_SMC_TIMINGS0 (ATMEL_BASE_SMC + 0x60c)
+#define AT91_ASM_SMC_MODE0 (ATMEL_BASE_SMC + 0x610)
#else
struct at91_cs {
u32 setup; /* 0x600 SMC Setup Register */
#define _ASM_ARMV8_FSL_LSCH3_CONFIG_
#include <fsl_ddrc_version.h>
-
+#define CONFIG_MP
#define CONFIG_SYS_FSL_OCRAM_BASE 0x18000000 /* initial RAM */
/* Link Definitions */
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
#define CONFIG_SYS_IMMR 0x01000000
#define CONFIG_SYS_FSL_DDR_ADDR (CONFIG_SYS_IMMR + 0x00080000)
#define CONFIG_SYS_FSL_DDR2_ADDR (CONFIG_SYS_IMMR + 0x00090000)
+#define CONFIG_SYS_FSL_DDR3_ADDR 0x08210000
#define CONFIG_SYS_FSL_GUTS_ADDR (CONFIG_SYS_IMMR + 0x00E00000)
#define CONFIG_SYS_FSL_PMU_ADDR (CONFIG_SYS_IMMR + 0x00E30000)
+#define CONFIG_SYS_FSL_RST_ADDR (CONFIG_SYS_IMMR + 0x00E60000)
#define CONFIG_SYS_FSL_CH3_CLK_GRPA_ADDR (CONFIG_SYS_IMMR + 0x00300000)
#define CONFIG_SYS_FSL_CH3_CLK_GRPB_ADDR (CONFIG_SYS_IMMR + 0x00310000)
#define CONFIG_SYS_FSL_CH3_CLK_CTRL_ADDR (CONFIG_SYS_IMMR + 0x00370000)
#ifdef CONFIG_LS2085A
#define CONFIG_MAX_CPUS 16
#define CONFIG_SYS_FSL_IFC_BANK_COUNT 8
-#define CONFIG_NUM_DDR_CONTROLLERS 2
+#define CONFIG_NUM_DDR_CONTROLLERS 3
#define CONFIG_SYS_FSL_CLUSTER_CLOCKS { 1, 1, 4, 4 }
#else
#error SoC not defined
u8 res_04[0x20-0x04];
} clkcncsr[8];
};
+
+struct ccsr_reset {
+ u32 rstcr; /* 0x000 */
+ u32 rstcrsp; /* 0x004 */
+ u8 res_008[0x10-0x08]; /* 0x008 */
+ u32 rstrqmr1; /* 0x010 */
+ u32 rstrqmr2; /* 0x014 */
+ u32 rstrqsr1; /* 0x018 */
+ u32 rstrqsr2; /* 0x01c */
+ u32 rstrqwdtmrl; /* 0x020 */
+ u32 rstrqwdtmru; /* 0x024 */
+ u8 res_028[0x30-0x28]; /* 0x028 */
+ u32 rstrqwdtsrl; /* 0x030 */
+ u32 rstrqwdtsru; /* 0x034 */
+ u8 res_038[0x60-0x38]; /* 0x038 */
+ u32 brrl; /* 0x060 */
+ u32 brru; /* 0x064 */
+ u8 res_068[0x80-0x68]; /* 0x068 */
+ u32 pirset; /* 0x080 */
+ u32 pirclr; /* 0x084 */
+ u8 res_088[0x90-0x88]; /* 0x088 */
+ u32 brcorenbr; /* 0x090 */
+ u8 res_094[0x100-0x94]; /* 0x094 */
+ u32 rcw_reqr; /* 0x100 */
+ u32 rcw_completion; /* 0x104 */
+ u8 res_108[0x110-0x108]; /* 0x108 */
+ u32 pbi_reqr; /* 0x110 */
+ u32 pbi_completion; /* 0x114 */
+ u8 res_118[0xa00-0x118]; /* 0x118 */
+ u32 qmbm_warmrst; /* 0xa00 */
+ u32 soc_warmrst; /* 0xa04 */
+ u8 res_a08[0xbf8-0xa08]; /* 0xa08 */
+ u32 ip_rev1; /* 0xbf8 */
+ u32 ip_rev2; /* 0xbfc */
+};
#endif /* __ARCH_FSL_LSCH3_IMMAP_H */
void ddr3_init(void);
void ddr3_reset_ddrphy(void);
+void ddr3_err_reset_workaround(void);
void ddr3_init_ddrphy(u32 base, struct ddr3_phy_config *phy_cfg);
void ddr3_init_ddremif(u32 base, struct ddr3_emif_config *emif_cfg);
#define KS2_CLOCK_BASE KS2_PLL_CNTRL_BASE
#define KS2_RSTCTRL_RSTYPE (KS2_PLL_CNTRL_BASE + 0xe4)
#define KS2_RSTCTRL (KS2_PLL_CNTRL_BASE + 0xe8)
+#define KS2_RSTCTRL_RSCFG (KS2_PLL_CNTRL_BASE + 0xec)
#define KS2_RSTCTRL_KEY 0x5a69
#define KS2_RSTCTRL_MASK 0xffff0000
#define KS2_RSTCTRL_SWRST 0xfffe0000
+#define KS2_RSTYPE_PLL_SOFT BIT(13)
/* SPI */
#define KS2_SPI0_BASE 0x21000400
#define KWSPI_XFERLEN_2BYTE (1 << 5)
#define KWSPI_XFERLEN_MASK (1 << 5)
#define KWSPI_ADRLEN_1BYTE 0
-#define KWSPI_ADRLEN_2BYTE 1 << 8
-#define KWSPI_ADRLEN_3BYTE 2 << 8
-#define KWSPI_ADRLEN_4BYTE 3 << 8
-#define KWSPI_ADRLEN_MASK 3 << 8
+#define KWSPI_ADRLEN_2BYTE (1 << 8)
+#define KWSPI_ADRLEN_3BYTE (2 << 8)
+#define KWSPI_ADRLEN_4BYTE (3 << 8)
+#define KWSPI_ADRLEN_MASK (3 << 8)
#define KWSPI_TIMEOUT 10000
#endif /* __KW_SPI_H__ */
#ifdef CONFIG_DDR_SPD
#define CONFIG_SYS_FSL_DDR_BE
#define CONFIG_VERY_BIG_RAM
+#ifdef CONFIG_SYS_FSL_DDR4
+#define CONFIG_SYS_FSL_DDRC_GEN4
+#else
#define CONFIG_SYS_FSL_DDRC_ARM_GEN3
+#endif
#define CONFIG_SYS_FSL_DDR
#define CONFIG_SYS_LS1_DDR_BLOCK1_SIZE ((phys_size_t)2 << 30)
#define CONFIG_MAX_MEM_MAPPED CONFIG_SYS_LS1_DDR_BLOCK1_SIZE
#define CONFIG_MAX_CPUS 2
#define CONFIG_SYS_FSL_IFC_BANK_COUNT 8
#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_5_0
#else
#error SoC not defined
#endif
u32 imx_get_uartclk(void);
u32 imx_get_fecclk(void);
unsigned int mxc_get_clock(enum mxc_clock clk);
+void setup_gpmi_io_clk(u32 cfg);
void enable_ocotp_clk(unsigned char enable);
void enable_usboh3_clk(unsigned char enable);
+void enable_uart_clk(unsigned char enable);
+int enable_cspi_clock(unsigned char enable, unsigned spi_num);
+int enable_usdhc_clk(unsigned char enable, unsigned bus_num);
int enable_sata_clock(void);
int enable_pcie_clock(void);
int enable_i2c_clk(unsigned char enable, unsigned i2c_num);
int enable_spi_clk(unsigned char enable, unsigned spi_num);
void enable_ipu_clock(void);
int enable_fec_anatop_clock(enum enet_freq freq);
+void enable_enet_clk(unsigned char enable);
#endif /* __ASM_ARCH_CLOCK_H */
u32 gpr[14];
};
+struct gpc {
+ u32 cntr;
+ u32 pgr;
+ u32 imr1;
+ u32 imr2;
+ u32 imr3;
+ u32 imr4;
+ u32 isr1;
+ u32 isr2;
+ u32 isr3;
+ u32 isr4;
+};
+
#define IOMUXC_GPR2_COUNTER_RESET_VAL_OFFSET 20
#define IOMUXC_GPR2_COUNTER_RESET_VAL_MASK (3<<IOMUXC_GPR2_COUNTER_RESET_VAL_OFFSET)
#define IOMUXC_GPR2_LVDS_CLK_SHIFT_OFFSET 16
#define IOMUXC_GPR1_REF_SSP_EN (1 << 16)
#define IOMUXC_GPR1_TEST_POWERDOWN (1 << 18)
+/*
+ * IOMUXC_GPR5 bit fields
+ */
+#define IOMUXC_GPR5_PCIE_BTNRST (1 << 19)
+#define IOMUXC_GPR5_PCIE_PERST (1 << 18)
+
/*
* IOMUXC_GPR8 bit fields
*/
/*
* IOMUXC_GPR12 bit fields
*/
+#define IOMUXC_GPR12_RX_EQ_2 (0x2 << 0)
+#define IOMUXC_GPR12_RX_EQ_MASK (0x7 << 0)
#define IOMUXC_GPR12_LOS_LEVEL_9 (0x9 << 4)
#define IOMUXC_GPR12_LOS_LEVEL_MASK (0x1f << 4)
#define IOMUXC_GPR12_APPS_LTSSM_ENABLE (1 << 10)
#define IOMUXC_GPR12_DEVICE_TYPE_EP (0x0 << 12)
#define IOMUXC_GPR12_DEVICE_TYPE_RC (0x4 << 12)
#define IOMUXC_GPR12_DEVICE_TYPE_MASK (0xf << 12)
+#define IOMUXC_GPR12_TEST_POWERDOWN (1 << 30)
/*
* IOMUXC_GPR13 bit fields
/* returns MXC_CPU_ value */
#define cpu_type(rev) (((rev) >> 12)&0xff)
-/* use with MXC_CPU_ constants */
-#define is_cpu_type(cpu) (cpu_type(get_cpu_rev()) == cpu)
+/* both macros return/take MXC_CPU_ constants */
+#define get_cpu_type() (cpu_type(get_cpu_rev()))
+#define is_cpu_type(cpu) (get_cpu_type() == cpu)
const char *get_imx_type(u32 imxtype);
unsigned imx_ddr_size(void);
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef ARCH_ARM_MPCORE_H
+#define ARCH_ARM_MPCORE_H
+
+/* Snoop Control Unit */
+#define SCU_OFFSET 0x00
+
+/* SCU Control Register */
+#define SCU_CTRL 0x00
+/* SCU Configuration Register */
+#define SCU_CONF 0x04
+/* SCU CPU Power Status Register */
+#define SCU_PWR_STATUS 0x08
+/* SCU Invalidate All Registers in Secure State */
+#define SCU_INV_ALL 0x0C
+/* SCU Filtering Start Address Register */
+#define SCU_FILTER_START 0x40
+/* SCU Filtering End Address Register */
+#define SCU_FILTER_END 0x44
+/* SCU Access Control Register */
+#define SCU_SAC 0x50
+/* SCU Non-secure Access Control Register */
+#define SCU_SNSAC 0x54
+
+/* Global Timer */
+#define GLOBAL_TIMER_OFFSET 0x200
+
+/* Global Timer Counter Registers */
+#define GTIMER_CNT_L 0x00
+#define GTIMER_CNT_H 0x04
+/* Global Timer Control Register */
+#define GTIMER_CTRL 0x08
+/* Global Timer Interrupt Status Register */
+#define GTIMER_STAT 0x0C
+/* Comparator Value Registers */
+#define GTIMER_CMP_L 0x10
+#define GTIMER_CMP_H 0x14
+/* Auto-increment Register */
+#define GTIMER_INC 0x18
+
+#endif /* ARCH_ARM_MPCORE_H */
--- /dev/null
+/*
+ * UniPhier BCU (Bus Control Unit) registers
+ *
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef ARCH_BCU_REGS_H
+#define ARCH_BCU_REGS_H
+
+#define BCU_BASE 0x50080000
+
+#define BCSCR(x) (BCU_BASE + 0x180 + (x) * 4)
+#define BCSCR0 (BCSCR(0))
+#define BCSCR1 (BCSCR(1))
+#define BCSCR2 (BCSCR(2))
+#define BCSCR3 (BCSCR(3))
+#define BCSCR4 (BCSCR(4))
+#define BCSCR5 (BCSCR(5))
+
+#define BCIPPCCHR(x) (BCU_BASE + 0x0280 + (x) * 4)
+#define BCIPPCCHR0 (BCIPPCCHR(0))
+#define BCIPPCCHR1 (BCIPPCCHR(1))
+#define BCIPPCCHR2 (BCIPPCCHR(2))
+#define BCIPPCCHR3 (BCIPPCCHR(3))
+#define BCIPPCCHR4 (BCIPPCCHR(4))
+#define BCIPPCCHR5 (BCIPPCCHR(5))
+
+#endif /* ARCH_BCU_REGS_H */
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef ARCH_BOARD_H
+#define ARCH_BOARD_H
+
+#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD) || \
+ defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
+void support_card_reset(void);
+void support_card_init(void);
+int check_support_card(void);
+#else
+#define support_card_reset() do {} while (0)
+#define support_card_init() do {} while (0)
+static inline int check_support_card(void)
+{
+ return 0;
+}
+#endif
+
+static inline void uniphier_board_reset(void)
+{
+ support_card_reset();
+}
+
+static inline void uniphier_board_init(void)
+{
+ support_card_init();
+}
+
+#endif /* ARCH_BOARD_H */
--- /dev/null
+/*
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _ASM_BOOT_DEVICE_H_
+#define _ASM_BOOT_DEVICE_H_
+
+u32 get_boot_mode_sel(void);
+
+struct boot_device_info {
+ u32 type;
+ char *info;
+};
+
+extern struct boot_device_info boot_device_table[];
+
+#endif /* _ASM_BOOT_DEVICE_H_ */
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef ARCH_LED_H
+#define ARCH_LED_H
+
+#include <config.h>
+
+#define LED_CHAR_0 0x7e
+#define LED_CHAR_1 0x0c
+#define LED_CHAR_2 0xb6
+#define LED_CHAR_3 0x9e
+#define LED_CHAR_4 0xcc
+#define LED_CHAR_5 0xda
+#define LED_CHAR_6 0xfa
+#define LED_CHAR_7 0x4e
+#define LED_CHAR_8 0xfe
+#define LED_CHAR_9 0xde
+
+#define LED_CHAR_A 0xee
+#define LED_CHAR_B 0xf8
+#define LED_CHAR_C 0x72
+#define LED_CHAR_D 0xbc
+#define LED_CHAR_E 0xf2
+#define LED_CHAR_F 0xe2
+#define LED_CHAR_G 0x7a
+#define LED_CHAR_H 0xe8
+#define LED_CHAR_I 0x08
+#define LED_CHAR_J 0x3c
+#define LED_CHAR_K 0xea
+#define LED_CHAR_L 0x70
+#define LED_CHAR_M 0x6e
+#define LED_CHAR_N 0xa8
+#define LED_CHAR_O 0xb8
+#define LED_CHAR_P 0xe6
+#define LED_CHAR_Q 0xce
+#define LED_CHAR_R 0xa0
+#define LED_CHAR_S 0xc8
+#define LED_CHAR_T 0x8c
+#define LED_CHAR_U 0x7c
+#define LED_CHAR_V 0x54
+#define LED_CHAR_W 0xfc
+#define LED_CHAR_X 0xec
+#define LED_CHAR_Y 0xdc
+#define LED_CHAR_Z 0xa4
+
+#define LED_CHAR_SPACE 0x00
+#define LED_CHAR_DOT 0x01
+
+#define LED_CHAR_ (LED_CHAR_SPACE)
+
+/** Macro to translate 4 characters into integer to display led */
+#define LED_C2I(C0, C1, C2, C3) \
+ (~( \
+ (LED_CHAR_##C0 << 24) | \
+ (LED_CHAR_##C1 << 16) | \
+ (LED_CHAR_##C2 << 8) | \
+ (LED_CHAR_##C3) \
+ ))
+
+#if defined(CONFIG_SUPPORT_CARD_LED_BASE)
+
+#define LED_ADDR CONFIG_SUPPORT_CARD_LED_BASE
+
+#ifdef __ASSEMBLY__
+
+#define led_write(C0, C1, C2, C3) raw_led_write LED_C2I(C0, C1, C2, C3)
+.macro raw_led_write data
+ ldr r0, =\data
+ ldr r1, =LED_ADDR
+ str r0, [r1]
+.endm
+
+#else /* __ASSEMBLY__ */
+
+#include <asm/io.h>
+
+#define led_write(C0, C1, C2, C3) \
+do { \
+ raw_led_write(LED_C2I(C0, C1, C2, C3)); \
+} while (0)
+
+static inline void raw_led_write(u32 data)
+{
+ writel(data, LED_ADDR);
+}
+
+#endif /* __ASSEMBLY__ */
+
+#else /* CONFIG_SUPPORT_CARD_LED_BASE */
+
+#define led_write(C0, C1, C2, C3)
+#define raw_led_write(x)
+
+#endif /* CONFIG_SUPPORT_CARD_LED_BASE */
+
+#endif /* ARCH_LED_H */
--- /dev/null
+/*
+ * UniPhier SBC (System Bus Controller) registers
+ *
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef ARCH_SBC_REGS_H
+#define ARCH_SBC_REGS_H
+
+#define SBBASE_BASE 0x58c00100
+#define SBBASE(x) (SBBASE_BASE + (x) * 0x10)
+
+#define SBBASE0 (SBBASE(0))
+#define SBBASE1 (SBBASE(1))
+#define SBBASE2 (SBBASE(2))
+#define SBBASE3 (SBBASE(3))
+#define SBBASE4 (SBBASE(4))
+#define SBBASE5 (SBBASE(5))
+#define SBBASE6 (SBBASE(6))
+#define SBBASE7 (SBBASE(7))
+
+#define SBBASE_BANK_ENABLE (0x00000001)
+
+#define SBCTRL_BASE 0x58c00200
+#define SBCTRL(x, y) (SBCTRL_BASE + (x) * 0x10 + (y) * 4)
+
+#define SBCTRL00 SBCTRL(0, 0)
+#define SBCTRL01 SBCTRL(0, 1)
+#define SBCTRL02 SBCTRL(0, 2)
+#define SBCTRL03 SBCTRL(0, 3)
+#define SBCTRL04 (SBCTRL_BASE + 0x100)
+
+#define SBCTRL10 SBCTRL(1, 0)
+#define SBCTRL11 SBCTRL(1, 1)
+#define SBCTRL12 SBCTRL(1, 2)
+#define SBCTRL13 SBCTRL(1, 3)
+#define SBCTRL14 (SBCTRL_BASE + 0x110)
+
+#define SBCTRL20 SBCTRL(2, 0)
+#define SBCTRL21 SBCTRL(2, 1)
+#define SBCTRL22 SBCTRL(2, 2)
+#define SBCTRL23 SBCTRL(2, 3)
+#define SBCTRL24 (SBCTRL_BASE + 0x120)
+
+#define SBCTRL30 SBCTRL(3, 0)
+#define SBCTRL31 SBCTRL(3, 1)
+#define SBCTRL32 SBCTRL(3, 2)
+#define SBCTRL33 SBCTRL(3, 3)
+#define SBCTRL34 (SBCTRL_BASE + 0x130)
+
+#define SBCTRL40 SBCTRL(4, 0)
+#define SBCTRL41 SBCTRL(4, 1)
+#define SBCTRL42 SBCTRL(4, 2)
+#define SBCTRL43 SBCTRL(4, 3)
+#define SBCTRL44 (SBCTRL_BASE + 0x140)
+
+#define SBCTRL50 SBCTRL(5, 0)
+#define SBCTRL51 SBCTRL(5, 1)
+#define SBCTRL52 SBCTRL(5, 2)
+#define SBCTRL53 SBCTRL(5, 3)
+#define SBCTRL54 (SBCTRL_BASE + 0x150)
+
+#define SBCTRL60 SBCTRL(6, 0)
+#define SBCTRL61 SBCTRL(6, 1)
+#define SBCTRL62 SBCTRL(6, 2)
+#define SBCTRL63 SBCTRL(6, 3)
+#define SBCTRL64 (SBCTRL_BASE + 0x160)
+
+#define SBCTRL70 SBCTRL(7, 0)
+#define SBCTRL71 SBCTRL(7, 1)
+#define SBCTRL72 SBCTRL(7, 2)
+#define SBCTRL73 SBCTRL(7, 3)
+#define SBCTRL74 (SBCTRL_BASE + 0x170)
+
+/* slower but LED works */
+#define SBCTRL0_SAVEPIN_PERI_VALUE 0x55450000
+#define SBCTRL1_SAVEPIN_PERI_VALUE 0x07168d00
+#define SBCTRL2_SAVEPIN_PERI_VALUE 0x34000009
+#define SBCTRL4_SAVEPIN_PERI_VALUE 0x02110110
+
+/* faster but LED does not work */
+#define SBCTRL0_SAVEPIN_MEM_VALUE 0x55450000
+#define SBCTRL1_SAVEPIN_MEM_VALUE 0x06057700
+/* NOR flash needs more wait counts than SRAM */
+#define SBCTRL2_SAVEPIN_MEM_VALUE 0x34000009
+#define SBCTRL4_SAVEPIN_MEM_VALUE 0x02110210
+
+#define SBCTRL0_ADMULTIPLX_PERI_VALUE 0x33120000
+#define SBCTRL1_ADMULTIPLX_PERI_VALUE 0x03005500
+#define SBCTRL2_ADMULTIPLX_PERI_VALUE 0x14000020
+
+#define SBCTRL0_ADMULTIPLX_MEM_VALUE 0x33120000
+#define SBCTRL1_ADMULTIPLX_MEM_VALUE 0x03005500
+#define SBCTRL2_ADMULTIPLX_MEM_VALUE 0x14000010
+
+#define ROM_BOOT_ROMRSV2 0x59801208
+
+#ifndef __ASSEMBLY__
+#include <asm/io.h>
+static inline int boot_is_swapped(void)
+{
+ return !(readl(SBBASE0) & SBBASE_BANK_ENABLE);
+}
+#endif
+
+#endif /* ARCH_SBC_REGS_H */
--- /dev/null
+/*
+ * UniPhier SC (System Control) block registers
+ *
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef ARCH_SC_REGS_H
+#define ARCH_SC_REGS_H
+
+#define SC_BASE_ADDR 0x61840000
+
+#define SC_MPLLOSCCTL (SC_BASE_ADDR | 0x1184)
+#define SC_MPLLOSCCTL_MPLLEN (0x1 << 0)
+#define SC_MPLLOSCCTL_MPLLST (0x1 << 1)
+
+#define SC_DPLLCTRL (SC_BASE_ADDR | 0x1200)
+#define SC_DPLLCTRL_SSC_EN (0x1 << 31)
+#define SC_DPLLCTRL_FOUTMODE_MASK (0xf << 16)
+#define SC_DPLLCTRL_SSC_RATE (0x1 << 15)
+
+#define SC_DPLLCTRL2 (SC_BASE_ADDR | 0x1204)
+#define SC_DPLLCTRL2_NRSTDS (0x1 << 28)
+
+#define SC_DPLLCTRL3 (SC_BASE_ADDR | 0x1208)
+#define SC_DPLLCTRL3_LPFSEL_COEF2 (0x0 << 31)
+#define SC_DPLLCTRL3_LPFSEL_COEF3 (0x1 << 31)
+
+#define SC_UPLLCTRL (SC_BASE_ADDR | 0x1210)
+
+#define SC_VPLL27ACTRL (SC_BASE_ADDR | 0x1270)
+#define SC_VPLL27ACTRL2 (SC_BASE_ADDR | 0x1274)
+#define SC_VPLL27ACTRL3 (SC_BASE_ADDR | 0x1278)
+
+#define SC_VPLL27BCTRL (SC_BASE_ADDR | 0x1290)
+#define SC_VPLL27BCTRL2 (SC_BASE_ADDR | 0x1294)
+#define SC_VPLL27BCTRL3 (SC_BASE_ADDR | 0x1298)
+
+#define SC_RSTCTRL (SC_BASE_ADDR | 0x2000)
+#define SC_RSTCTRL_NRST_ETHER (0x1 << 12)
+#define SC_RSTCTRL_NRST_UMC1 (0x1 << 5)
+#define SC_RSTCTRL_NRST_UMC0 (0x1 << 4)
+#define SC_RSTCTRL_NRST_NAND (0x1 << 2)
+
+#define SC_RSTCTRL2 (SC_BASE_ADDR | 0x2004)
+#define SC_RSTCTRL3 (SC_BASE_ADDR | 0x2008)
+
+#define SC_CLKCTRL (SC_BASE_ADDR | 0x2104)
+#define SC_CLKCTRL_CLK_ETHER (0x1 << 12)
+#define SC_CLKCTRL_CLK_MIO (0x1 << 11)
+#define SC_CLKCTRL_CLK_UMC (0x1 << 4)
+#define SC_CLKCTRL_CLK_NAND (0x1 << 2)
+#define SC_CLKCTRL_CLK_SBC (0x1 << 1)
+#define SC_CLKCTRL_CLK_PERI (0x1 << 0)
+
+/* System reset control register */
+#define SC_IRQTIMSET (SC_BASE_ADDR | 0x3000)
+#define SC_SLFRSTSEL (SC_BASE_ADDR | 0x3010)
+#define SC_SLFRSTCTL (SC_BASE_ADDR | 0x3014)
+
+#endif /* ARCH_SC_REGS_H */
--- /dev/null
+/*
+ * UniPhier SG (SoC Glue) block registers
+ *
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef ARCH_SG_REGS_H
+#define ARCH_SG_REGS_H
+
+/* Base Address */
+#define SG_CTRL_BASE 0x5f800000
+#define SG_DBG_BASE 0x5f900000
+
+/* Revision */
+#define SG_REVISION (SG_CTRL_BASE | 0x0000)
+#define SG_REVISION_TYPE_SHIFT 16
+#define SG_REVISION_TYPE_MASK (0xff << SG_REVISION_TYPE_SHIFT)
+#define SG_REVISION_MODEL_SHIFT 8
+#define SG_REVISION_MODEL_MASK (0x3 << SG_REVISION_MODEL_SHIFT)
+#define SG_REVISION_REV_SHIFT 0
+#define SG_REVISION_REV_MASK (0x1f << SG_REVISION_REV_SHIFT)
+
+/* Memory Configuration */
+#define SG_MEMCONF (SG_CTRL_BASE | 0x0400)
+
+#define SG_MEMCONF_CH0_SIZE_64MB ((0x0 << 10) | (0x01 << 0))
+#define SG_MEMCONF_CH0_SIZE_128MB ((0x0 << 10) | (0x02 << 0))
+#define SG_MEMCONF_CH0_SIZE_256MB ((0x0 << 10) | (0x03 << 0))
+#define SG_MEMCONF_CH0_SIZE_512MB ((0x1 << 10) | (0x00 << 0))
+#define SG_MEMCONF_CH0_SIZE_1024MB ((0x1 << 10) | (0x01 << 0))
+#define SG_MEMCONF_CH0_NUM_1 (0x1 << 8)
+#define SG_MEMCONF_CH0_NUM_2 (0x0 << 8)
+
+#define SG_MEMCONF_CH1_SIZE_64MB ((0x0 << 11) | (0x01 << 2))
+#define SG_MEMCONF_CH1_SIZE_128MB ((0x0 << 11) | (0x02 << 2))
+#define SG_MEMCONF_CH1_SIZE_256MB ((0x0 << 11) | (0x03 << 2))
+#define SG_MEMCONF_CH1_SIZE_512MB ((0x1 << 11) | (0x00 << 2))
+#define SG_MEMCONF_CH1_SIZE_1024MB ((0x1 << 11) | (0x01 << 2))
+#define SG_MEMCONF_CH1_NUM_1 (0x1 << 9)
+#define SG_MEMCONF_CH1_NUM_2 (0x0 << 9)
+
+#define SG_MEMCONF_SPARSEMEM (0x1 << 4)
+
+/* Pin Control */
+#define SG_PINCTRL_BASE (SG_CTRL_BASE | 0x1000)
+
+#if defined(CONFIG_MACH_PH1_PRO4)
+# define SG_PINCTRL(n) (SG_PINCTRL_BASE + (n) * 8)
+#elif defined(CONFIG_MACH_PH1_LD4) || defined(CONFIG_MACH_PH1_SLD8)
+# define SG_PINCTRL(n) (SG_PINCTRL_BASE + (n) * 4)
+#endif
+
+#if defined(CONFIG_MACH_PH1_PRO4)
+#define SG_PINSELBITS 4
+#elif defined(CONFIG_MACH_PH1_LD4) || defined(CONFIG_MACH_PH1_SLD8)
+#define SG_PINSELBITS 8
+#endif
+
+#define SG_PINSEL_ADDR(n) (SG_PINCTRL((n) * (SG_PINSELBITS) / 32))
+#define SG_PINSEL_MASK(n) (~(((1 << (SG_PINSELBITS)) - 1) << \
+ ((n) * (SG_PINSELBITS) % 32)))
+#define SG_PINSEL_MODE(n, mode) ((mode) << ((n) * (SG_PINSELBITS) % 32))
+
+/* Only for PH1-Pro4 */
+#define SG_LOADPINCTRL (SG_CTRL_BASE | 0x1700)
+
+/* Input Enable */
+#define SG_IECTRL (SG_CTRL_BASE | 0x1d00)
+
+/* Pin Monitor */
+#define SG_PINMON0 (SG_DBG_BASE | 0x0100)
+
+#define SG_PINMON0_CLK_MODE_UPLLSRC_MASK (0x3 << 19)
+#define SG_PINMON0_CLK_MODE_UPLLSRC_DEFAULT (0x0 << 19)
+#define SG_PINMON0_CLK_MODE_UPLLSRC_VPLL27A (0x2 << 19)
+#define SG_PINMON0_CLK_MODE_UPLLSRC_VPLL27B (0x3 << 19)
+
+#define SG_PINMON0_CLK_MODE_AXOSEL_MASK (0x3 << 16)
+#define SG_PINMON0_CLK_MODE_AXOSEL_24576KHZ (0x0 << 16)
+#define SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ (0x1 << 16)
+#define SG_PINMON0_CLK_MODE_AXOSEL_6144KHZ (0x2 << 16)
+#define SG_PINMON0_CLK_MODE_AXOSEL_6250KHZ (0x3 << 16)
+
+#define SG_PINMON0_CLK_MODE_AXOSEL_DEFAULT (0x0 << 16)
+#define SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_U (0x1 << 16)
+#define SG_PINMON0_CLK_MODE_AXOSEL_20480KHZ (0x2 << 16)
+#define SG_PINMON0_CLK_MODE_AXOSEL_25000KHZ_A (0x3 << 16)
+
+#ifndef __ASSEMBLY__
+#include <linux/types.h>
+#include <asm/io.h>
+
+static inline void sg_set_pinsel(int n, int value)
+{
+ writel((readl(SG_PINSEL_ADDR(n)) & SG_PINSEL_MASK(n))
+ | SG_PINSEL_MODE(n, value), SG_PINSEL_ADDR(n));
+}
+
+static inline u32 sg_memconf_val_ch0(unsigned long size, int num)
+{
+ int size_mb = (size >> 20) / num;
+ u32 ret;
+
+ switch (size_mb) {
+ case 64:
+ ret = SG_MEMCONF_CH0_SIZE_64MB;
+ break;
+ case 128:
+ ret = SG_MEMCONF_CH0_SIZE_128MB;
+ break;
+ case 256:
+ ret = SG_MEMCONF_CH0_SIZE_256MB;
+ break;
+ case 512:
+ ret = SG_MEMCONF_CH0_SIZE_512MB;
+ break;
+ case 1024:
+ ret = SG_MEMCONF_CH0_SIZE_1024MB;
+ break;
+ default:
+ BUG();
+ break;
+ }
+
+ switch (num) {
+ case 1:
+ ret |= SG_MEMCONF_CH0_NUM_1;
+ break;
+ case 2:
+ ret |= SG_MEMCONF_CH0_NUM_2;
+ break;
+ default:
+ BUG();
+ break;
+ }
+ return ret;
+}
+
+static inline u32 sg_memconf_val_ch1(unsigned long size, int num)
+{
+ int size_mb = (size >> 20) / num;
+ u32 ret;
+
+ switch (size_mb) {
+ case 64:
+ ret = SG_MEMCONF_CH1_SIZE_64MB;
+ break;
+ case 128:
+ ret = SG_MEMCONF_CH1_SIZE_128MB;
+ break;
+ case 256:
+ ret = SG_MEMCONF_CH1_SIZE_256MB;
+ break;
+ case 512:
+ ret = SG_MEMCONF_CH1_SIZE_512MB;
+ break;
+ case 1024:
+ ret = SG_MEMCONF_CH1_SIZE_1024MB;
+ break;
+ default:
+ BUG();
+ break;
+ }
+
+ switch (num) {
+ case 1:
+ ret |= SG_MEMCONF_CH1_NUM_1;
+ break;
+ case 2:
+ ret |= SG_MEMCONF_CH1_NUM_2;
+ break;
+ default:
+ BUG();
+ break;
+ }
+ return ret;
+}
+#endif /* __ASSEMBLY__ */
+
+#endif /* ARCH_SG_REGS_H */
--- /dev/null
+/*
+ * UniPhier System Cache (L2 Cache) registers
+ *
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef ARCH_SSC_REGS_H
+#define ARCH_SSC_REGS_H
+
+#define SSCC 0x500c0000
+#define SSCC_BST (0x1 << 20)
+#define SSCC_ACT (0x1 << 19)
+#define SSCC_WTG (0x1 << 18)
+#define SSCC_PRD (0x1 << 17)
+#define SSCC_WBWA (0x1 << 16)
+#define SSCC_EX (0x1 << 13)
+#define SSCC_ON (0x1 << 0)
+
+#define SSCLPDAWCR 0x500c0030
+
+#define SSCOPE 0x506c0244
+#define SSCOPE_CM_SYNC 0x00000008
+
+#define SSCOQM 0x506c0248
+#define SSCOQM_TID_MASK (0x3 << 21)
+#define SSCOQM_TID_BY_WAY (0x2 << 21)
+#define SSCOQM_TID_BY_INST_WAY (0x1 << 21)
+#define SSCOQM_TID_BY_DATA_WAY (0x0 << 21)
+#define SSCOQM_S_MASK (0x3 << 17)
+#define SSCOQM_S_WAY (0x2 << 17)
+#define SSCOQM_S_ALL (0x1 << 17)
+#define SSCOQM_S_ADDRESS (0x0 << 17)
+#define SSCOQM_CE (0x1 << 15)
+#define SSCOQM_CW (0x1 << 14)
+#define SSCOQM_CM_MASK (0x7)
+#define SSCOQM_CM_DIRT_TOUCH (0x7)
+#define SSCOQM_CM_ZERO_TOUCH (0x6)
+#define SSCOQM_CM_NORM_TOUCH (0x5)
+#define SSCOQM_CM_PREF_FETCH (0x4)
+#define SSCOQM_CM_SSC_FETCH (0x3)
+#define SSCOQM_CM_WB_INV (0x2)
+#define SSCOQM_CM_WB (0x1)
+#define SSCOQM_CM_INV (0x0)
+
+#define SSCOQAD 0x506c024c
+#define SSCOQSZ 0x506c0250
+#define SSCOQWN 0x506c0258
+
+#define SSCOPPQSEF 0x506c025c
+#define SSCOPPQSEF_FE (0x1 << 1)
+#define SSCOPPQSEF_OE (0x1 << 0)
+
+#define SSCOLPQS 0x506c0260
+#define SSCOLPQS_EF (0x1 << 2)
+#define SSCOLPQS_EST (0x1 << 1)
+#define SSCOLPQS_QST (0x1 << 0)
+
+#define SSCOQCE0 0x506c0270
+
+#define SSC_LINE_SIZE 128
+#define SSC_NUM_ENTRIES 256
+#define SSC_WAY_SIZE ((SSC_LINE_SIZE) * (SSC_NUM_ENTRIES))
+#define SSC_RANGE_OP_MAX_SIZE (0x00400000 - (SSC_LINE_SIZE))
+
+#endif /* ARCH_SSC_REGS_H */
--- /dev/null
+/*
+ * UniPhier UMC (Universal Memory Controller) registers
+ *
+ * Copyright (C) 2011-2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef ARCH_UMC_REGS_H
+#define ARCH_UMC_REGS_H
+
+#define UMC_BASE 0x5b800000
+
+/* SSIF registers */
+#define UMC_SSIF_BASE UMC_BASE
+
+#define UMC_CPURST 0x00000700
+#define UMC_IDSRST 0x0000070C
+#define UMC_IXMRST 0x00000714
+#define UMC_HDMRST 0x00000718
+#define UMC_MDMRST 0x0000071C
+#define UMC_HDDRST 0x00000720
+#define UMC_MDDRST 0x00000724
+#define UMC_SIORST 0x00000728
+#define UMC_GIORST 0x0000072C
+#define UMC_HD2RST 0x00000734
+#define UMC_VIORST 0x0000073C
+#define UMC_FRCRST 0x00000748 /* LD4/sLD8 */
+#define UMC_DVCRST 0x00000748 /* Pro4 */
+#define UMC_RGLRST 0x00000750
+#define UMC_VPERST 0x00000758
+#define UMC_AIORST 0x00000764
+#define UMC_DMDRST 0x00000770
+
+#define UMC_HDMCHSEL 0x00000898
+#define UMC_MDMCHSEL 0x0000089C
+#define UMC_DVCCHSEL 0x000008C8
+#define UMC_DMDCHSEL 0x000008F0
+
+#define UMC_CLKEN_SSIF_FETCH 0x0000C060
+#define UMC_CLKEN_SSIF_COMQUE0 0x0000C064
+#define UMC_CLKEN_SSIF_COMWC0 0x0000C068
+#define UMC_CLKEN_SSIF_COMRC0 0x0000C06C
+#define UMC_CLKEN_SSIF_COMQUE1 0x0000C070
+#define UMC_CLKEN_SSIF_COMWC1 0x0000C074
+#define UMC_CLKEN_SSIF_COMRC1 0x0000C078
+#define UMC_CLKEN_SSIF_WC 0x0000C07C
+#define UMC_CLKEN_SSIF_RC 0x0000C080
+#define UMC_CLKEN_SSIF_DST 0x0000C084
+
+/* CA registers */
+#define UMC_CA_BASE(ch) (UMC_BASE + 0x00001000 + 0x00001000 * (ch))
+
+/* DRAM controller registers */
+#define UMC_DRAMCONT_BASE(ch) (UMC_BASE + 0x00400000 + 0x00200000 * (ch))
+
+#define UMC_CMDCTLA 0x00000000
+#define UMC_CMDCTLB 0x00000004
+#define UMC_INITCTLA 0x00000008
+#define UMC_INITCTLB 0x0000000C
+#define UMC_INITCTLC 0x00000010
+#define UMC_INITSET 0x00000014
+#define UMC_INITSTAT 0x00000018
+#define UMC_DRMMR0 0x0000001C
+#define UMC_DRMMR1 0x00000020
+#define UMC_DRMMR2 0x00000024
+#define UMC_DRMMR3 0x00000028
+#define UMC_SPCCTLA 0x00000030
+#define UMC_SPCCTLB 0x00000034
+#define UMC_SPCSETA 0x00000038
+#define UMC_SPCSETB 0x0000003C
+#define UMC_SPCSETC 0x00000040
+#define UMC_SPCSETD 0x00000044
+#define UMC_SPCSTATA 0x00000050
+#define UMC_SPCSTATB 0x00000054
+#define UMC_SPCSTATC 0x00000058
+#define UMC_ACSSETA 0x00000060
+#define UMC_FLOWCTLA 0x00000400
+#define UMC_FLOWCTLB 0x00000404
+#define UMC_FLOWCTLC 0x00000408
+#define UMC_FLOWCTLG 0x00000508
+#define UMC_RDATACTL_D0 0x00000600
+#define UMC_WDATACTL_D0 0x00000604
+#define UMC_RDATACTL_D1 0x00000608
+#define UMC_WDATACTL_D1 0x0000060C
+#define UMC_DATASET 0x00000610
+#define UMC_DCCGCTL 0x00000720
+#define UMC_DICGCTLA 0x00000724
+#define UMC_DICGCTLB 0x00000728
+#define UMC_DIOCTLA 0x00000C00
+#define UMC_DFICUPDCTLA 0x00000C20
+
+#ifndef __ASSEMBLY__
+
+#include <linux/types.h>
+
+static inline void umc_polling(u32 address, u32 expval, u32 mask)
+{
+ u32 nmask = ~mask;
+ u32 data;
+ do {
+ data = readl(address) & nmask;
+ } while (data != expval);
+}
+
+static inline void umc_dram_init_start(void __iomem *dramcont)
+{
+ writel(0x00000002, dramcont + UMC_INITSET);
+}
+
+static inline void umc_dram_init_poll(void __iomem *dramcont)
+{
+ while ((readl(dramcont + UMC_INITSTAT) & 0x00000002))
+ ;
+}
+
+#endif
+
+#endif
struct i2c_pin_ctrl sda;
};
+#if defined(CONFIG_MX6QDL)
+#define I2C_PADS(name, scl_i2c, scl_gpio, scl_gp, sda_i2c, sda_gpio, sda_gp) \
+ struct i2c_pads_info mx6q_##name = { \
+ .scl = { \
+ .i2c_mode = MX6Q_##scl_i2c, \
+ .gpio_mode = MX6Q_##scl_gpio, \
+ .gp = scl_gp, \
+ }, \
+ .sda = { \
+ .i2c_mode = MX6Q_##sda_i2c, \
+ .gpio_mode = MX6Q_##sda_gpio, \
+ .gp = sda_gp, \
+ } \
+ }; \
+ struct i2c_pads_info mx6s_##name = { \
+ .scl = { \
+ .i2c_mode = MX6DL_##scl_i2c, \
+ .gpio_mode = MX6DL_##scl_gpio, \
+ .gp = scl_gp, \
+ }, \
+ .sda = { \
+ .i2c_mode = MX6DL_##sda_i2c, \
+ .gpio_mode = MX6DL_##sda_gpio, \
+ .gp = sda_gp, \
+ } \
+ };
+
+
+#define I2C_PADS_INFO(name) \
+ (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) ? \
+ &mx6q_##name : &mx6s_##name
+#endif
+
void setup_i2c(unsigned i2c_index, int speed, int slave_addr,
struct i2c_pads_info *p);
void bus_i2c_init(void *base, int speed, int slave_addr,
cbz \xreg1, \master_label
.endm
+.macro armv8_switch_to_el2_m, xreg1
+ /* 64bit EL2 | HCE | SMD | RES1 (Bits[5:4]) | Non-secure EL0/EL1 */
+ mov \xreg1, #0x5b1
+ msr scr_el3, \xreg1
+ msr cptr_el3, xzr /* Disable coprocessor traps to EL3 */
+ mov \xreg1, #0x33ff
+ msr cptr_el2, \xreg1 /* Disable coprocessor traps to EL2 */
+
+ /* Initialize SCTLR_EL2
+ *
+ * setting RES1 bits (29,28,23,22,18,16,11,5,4) to 1
+ * and RES0 bits (31,30,27,26,24,21,20,17,15-13,10-6) +
+ * EE,WXN,I,SA,C,A,M to 0
+ */
+ mov \xreg1, #0x0830
+ movk \xreg1, #0x30C5, lsl #16
+ msr sctlr_el2, \xreg1
+
+ /* Return to the EL2_SP2 mode from EL3 */
+ mov \xreg1, sp
+ msr sp_el2, \xreg1 /* Migrate SP */
+ mrs \xreg1, vbar_el3
+ msr vbar_el2, \xreg1 /* Migrate VBAR */
+ mov \xreg1, #0x3c9
+ msr spsr_el3, \xreg1 /* EL2_SP2 | D | A | I | F */
+ msr elr_el3, lr
+ eret
+.endm
+
+.macro armv8_switch_to_el1_m, xreg1, xreg2
+ /* Initialize Generic Timers */
+ mrs \xreg1, cnthctl_el2
+ orr \xreg1, \xreg1, #0x3 /* Enable EL1 access to timers */
+ msr cnthctl_el2, \xreg1
+ msr cntvoff_el2, xzr
+
+ /* Initilize MPID/MPIDR registers */
+ mrs \xreg1, midr_el1
+ mrs \xreg2, mpidr_el1
+ msr vpidr_el2, \xreg1
+ msr vmpidr_el2, \xreg2
+
+ /* Disable coprocessor traps */
+ mov \xreg1, #0x33ff
+ msr cptr_el2, \xreg1 /* Disable coprocessor traps to EL2 */
+ msr hstr_el2, xzr /* Disable coprocessor traps to EL2 */
+ mov \xreg1, #3 << 20
+ msr cpacr_el1, \xreg1 /* Enable FP/SIMD at EL1 */
+
+ /* Initialize HCR_EL2 */
+ mov \xreg1, #(1 << 31) /* 64bit EL1 */
+ orr \xreg1, \xreg1, #(1 << 29) /* Disable HVC */
+ msr hcr_el2, \xreg1
+
+ /* SCTLR_EL1 initialization
+ *
+ * setting RES1 bits (29,28,23,22,20,11) to 1
+ * and RES0 bits (31,30,27,21,17,13,10,6) +
+ * UCI,EE,EOE,WXN,nTWE,nTWI,UCT,DZE,I,UMA,SED,ITD,
+ * CP15BEN,SA0,SA,C,A,M to 0
+ */
+ mov \xreg1, #0x0800
+ movk \xreg1, #0x30d0, lsl #16
+ msr sctlr_el1, \xreg1
+
+ /* Return to the EL1_SP1 mode from EL2 */
+ mov \xreg1, sp
+ msr sp_el1, \xreg1 /* Migrate SP */
+ mrs \xreg1, vbar_el2
+ msr vbar_el1, \xreg1 /* Migrate VBAR */
+ mov \xreg1, #0x3c5
+ msr spsr_el2, \xreg1 /* EL1_SP1 | D | A | I | F */
+ msr elr_el2, lr
+ eret
+.endm
+
+#if defined(CONFIG_GICV3)
+.macro gic_wait_for_interrupt_m xreg1
+0 : wfi
+ mrs \xreg1, ICC_IAR1_EL1
+ msr ICC_EOIR1_EL1, \xreg1
+ cbnz \xreg1, 0b
+.endm
+#elif defined(CONFIG_GICV2)
+.macro gic_wait_for_interrupt_m xreg1, wreg2
+0 : wfi
+ ldr \wreg2, [\xreg1, GICC_AIAR]
+ str \wreg2, [\xreg1, GICC_AEOIR]
+ and \wreg2, \wreg2, #3ff
+ cbnz \wreg2, 0b
+.endm
+#endif
+
#endif /* CONFIG_ARM64 */
#endif /* __ASSEMBLY__ */
#include <asm-offsets.h>
#include <config.h>
#include <linux/linkage.h>
-#include <asm/macro.h>
#include <asm/gic.h>
+#include <asm/macro.h>
/*************************************************************************
*
*************************************************************************/
ENTRY(gic_wait_for_interrupt)
-0: wfi
#if defined(CONFIG_GICV3)
- mrs x9, ICC_IAR1_EL1
- msr ICC_EOIR1_EL1, x9
+ gic_wait_for_interrupt_m x9
#elif defined(CONFIG_GICV2)
- ldr w9, [x0, GICC_AIAR]
- str w9, [x0, GICC_AEOIR]
+ gic_wait_for_interrupt_m x0, w9
#endif
- cbnz w9, 0b
ret
ENDPROC(gic_wait_for_interrupt)
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
+ /* Set global data pointer. */
+ gd = &gdata;
+
board_init_r(NULL, 0);
}
CONFIG_STANDALONE_LOAD_ADDR ?= 0x40000
LDFLAGS_FINAL += --gc-sections
+LDFLAGS_FINAL += --bss-plt
PLATFORM_RELFLAGS += -fpic -mrelocatable -ffunction-sections -fdata-sections \
-meabi
PLATFORM_CPPFLAGS += -D__powerpc__ -ffixed-r2
/* Board-specific functions defined in each board's ddr.c */
void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd,
- unsigned int ctrl_num);
+ unsigned int ctrl_num, unsigned int dimm_slots_per_ctrl);
void read_tlbcam_entry(int idx, u32 *valid, u32 *tsize, unsigned long *epn,
phys_addr_t *rpn);
unsigned int
spd[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR];
for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++)
- fsl_ddr_get_spd(spd[i], i);
+ fsl_ddr_get_spd(spd[i], i, CONFIG_DIMM_SLOTS_PER_CTLR);
puts("SPD data of all dimms (zero vaule is omitted)...\n");
puts("Byte (hex) ");
#endif
cfg = in_be32(&gur->rcwsr[4]) & sd_prctl_mask;
- /* Is serdes enabled at all? */
- if (!cfg) {
- printf("SERDES%d is not enabled\n", sd + 1);
- return 0;
- }
/* Erratum A-007186
* Freescale Scratch Pad Fuse Register n (SFP_FSPFR0)
/*
- * Copyright 2009-2012 Freescale Semiconductor, Inc.
+ * Copyright 2009-2014 Freescale Semiconductor, Inc.
*
* This file is derived from arch/powerpc/cpu/mpc85xx/cpu.c and
* arch/powerpc/cpu/mpc86xx/cpu.c. Basically this file contains
{
const char *modes[] = { "host", "peripheral", "otg" };
const char *phys[] = { "ulpi", "utmi" };
- const char *dr_mode_type = NULL;
- const char *dr_phy_type = NULL;
int usb_mode_off = -1;
int usb_phy_off = -1;
char str[5];
int i, j;
for (i = 1; i <= CONFIG_USB_MAX_CONTROLLER_COUNT; i++) {
+ const char *dr_mode_type = NULL;
+ const char *dr_phy_type = NULL;
int mode_idx = -1, phy_idx = -1;
snprintf(str, 5, "%s%d", "usb", i);
if (hwconfig(str)) {
}
}
- if (mode_idx < 0 || phy_idx < 0) {
- puts("ERROR: wrong usb mode/phy defined!!\n");
- return;
- }
-
- dr_mode_type = modes[mode_idx];
- dr_phy_type = phys[phy_idx];
-
if (mode_idx < 0 && phy_idx < 0) {
printf("WARNING: invalid phy or mode\n");
return;
}
+
+ if (mode_idx > -1)
+ dr_mode_type = modes[mode_idx];
+
+ if (phy_idx > -1)
+ dr_phy_type = phys[phy_idx];
}
usb_mode_off = fdt_fixup_usb_mode_phy_type(blob,
/* Handle memory below 4GB. */
if (start <= max_addr) {
- phys_size_t low_size = MIN(max_addr + 1 - start, size);
+ phys_size_t low_size = min(max_addr + 1 - start, size);
void *start_ptr = (void *)(uintptr_t)start;
assert(((phys_addr_t)(uintptr_t)start) == start);
/* Handle the first partial page. */
if (offset) {
phys_addr_t end =
- MIN(map_addr + LARGE_PAGE_SIZE, start + size);
+ min(map_addr + LARGE_PAGE_SIZE, start + size);
phys_size_t cur_size = end - start;
x86_phys_memset_page(map_addr, offset, c, cur_size);
size -= cur_size;
NET2BIG_V2 BOARD
-M: -
+#M: -
S: Maintained
F: board/LaCie/net2big_v2/
F: include/configs/lacie_kw.h
F: configs/netspace_v2_defconfig
NETSPACE_LITE_V2 BOARD
-M: -
+#M: -
S: Maintained
F: configs/netspace_lite_v2_defconfig
F: configs/netspace_mini_v2_defconfig
WIRELESS_SPACE BOARD
-M: -
+#M: -
S: Maintained
F: board/LaCie/wireless_space/
F: include/configs/wireless_space.h
DB64360 BOARD
-M: -
+#M: -
S: Maintained
F: board/Marvell/db64360/
F: include/configs/DB64360.h
DB64460 BOARD
-M: -
+#M: -
S: Maintained
F: board/Marvell/db64460/
F: include/configs/DB64460.h
F: configs/openrd_base_defconfig
OPENRD_CLIENT BOARD
-M: -
+#M: -
S: Maintained
F: configs/openrd_client_defconfig
F: configs/openrd_ultimate_defconfig
A3000 BOARD
-M: -
+#M: -
S: Maintained
F: board/a3000/
F: include/configs/A3000.h
BLUESTONE BOARD
-M: Tirumala Marri <tmarri@apm.com>
+#M: Tirumala Marri <tmarri@apm.com>
S: Orphan (since 2014-03)
F: board/amcc/bluestone/
F: include/configs/bluestone.h
BUBINGA BOARD
-M: -
+#M: -
S: Maintained
F: board/amcc/bubinga/
F: include/configs/bubinga.h
YUCCA BOARD
-M: -
+#M: -
S: Maintained
F: board/amcc/yucca/
F: include/configs/yucca.h
VERSATILE BOARD
-M: -
+#M: -
S: Maintained
F: board/armltd/versatile/
F: include/configs/versatile.h
VEXPRESS BOARD
-M: -
+#M: -
S: Maintained
F: board/armltd/vexpress/
F: include/configs/vexpress_ca15_tc2.h
F: configs/vexpress_ca15_tc2_defconfig
VEXPRESS_CA5X2 BOARD
-M: Matt Waddel <matt.waddel@linaro.org>
+#M: Matt Waddel <matt.waddel@linaro.org>
S: Orphan (since 2014-08)
F: include/configs/vexpress_ca5x2.h
F: configs/vexpress_ca5x2_defconfig
if TARGET_VEXPRESS_AEMV8A
-config SYS_CPU
- default "armv8"
-
-config SYS_BOARD
- default "vexpress64"
-
-config SYS_VENDOR
- default "armltd"
-
-config SYS_CONFIG_NAME
- default "vexpress_aemv8a"
-
-endif
-
-if TARGET_VEXPRESS_AEMV8A_SEMI
-
-config SYS_CPU
- default "armv8"
-
config SYS_BOARD
default "vexpress64"
ATNGW100 BOARD
-M: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
+#M: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
S: Orphan (since 2014-06)
F: board/atmel/atngw100/
F: include/configs/atngw100.h
ATSTK1000 BOARD
-M: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
+#M: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
S: Orphan (since 2014-06)
F: board/atmel/atstk1000/
F: include/configs/atstk1002.h
}
#endif
+#ifndef CONFIG_SYS_NO_FLASH
+static void sama5d3xek_nor_hw_init(void)
+{
+ struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
+
+ at91_periph_clk_enable(ATMEL_ID_SMC);
+
+ /* Configure SMC CS0 for NOR flash */
+ writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
+ AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
+ &smc->cs[0].setup);
+ writel(AT91_SMC_PULSE_NWE(10) | AT91_SMC_PULSE_NCS_WR(11) |
+ AT91_SMC_PULSE_NRD(10) | AT91_SMC_PULSE_NCS_RD(11),
+ &smc->cs[0].pulse);
+ writel(AT91_SMC_CYCLE_NWE(11) | AT91_SMC_CYCLE_NRD(14),
+ &smc->cs[0].cycle);
+ writel(AT91_SMC_TIMINGS_TCLR(0) | AT91_SMC_TIMINGS_TADL(0) |
+ AT91_SMC_TIMINGS_TAR(0) | AT91_SMC_TIMINGS_TRR(0) |
+ AT91_SMC_TIMINGS_TWB(0) | AT91_SMC_TIMINGS_RBNSEL(0)|
+ AT91_SMC_TIMINGS_NFSEL(0), &smc->cs[0].timings);
+ writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
+ AT91_SMC_MODE_EXNW_DISABLE |
+ AT91_SMC_MODE_DBW_16 |
+ AT91_SMC_MODE_TDF_CYCLE(1),
+ &smc->cs[0].mode);
+
+ /* Address pin (A1 ~ A23) configuration */
+ at91_set_a_periph(AT91_PIO_PORTE, 1, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 2, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 3, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 4, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 5, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 6, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 7, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 8, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 9, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 10, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 11, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 12, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 13, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 14, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 15, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 16, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 17, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 18, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 19, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 20, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 21, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 22, 0);
+ at91_set_a_periph(AT91_PIO_PORTE, 23, 0);
+ /* CS0 pin configuration */
+ at91_set_a_periph(AT91_PIO_PORTE, 26, 0);
+}
+#endif
+
#ifdef CONFIG_CMD_USB
static void sama5d3xek_usb_hw_init(void)
{
#ifdef CONFIG_NAND_ATMEL
sama5d3xek_nand_hw_init();
#endif
+#ifndef CONFIG_SYS_NO_FLASH
+ sama5d3xek_nor_hw_init();
+#endif
#ifdef CONFIG_CMD_USB
sama5d3xek_usb_hw_init();
#endif
BC3450 BOARD
-M: -
+#M: -
S: Maintained
F: board/bc3450/
F: include/configs/BC3450.h
#endif
#ifdef CONFIG_MXC_SPI
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+ return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -1;
+}
+
iomux_v3_cfg_t const ecspi1_pads[] = {
/* SS1 */
MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
SBC35_A9G20 BOARD
-
M: Albin Tonnerre <albin.tonnerre@free-electrons.com>
+
#M: Albin Tonnerre <albin.tonnerre@free-electrons.com>
S: Orphan (since 2014-06)
F: board/calao/sbc35_a9g20/
F: include/configs/sbc35_a9g20.h
TNY_A9260 BOARD
-
M: Albin Tonnerre <albin.tonnerre@free-electrons.com>
+
#M: Albin Tonnerre <albin.tonnerre@free-electrons.com>
S: Orphan (since 2014-06)
F: board/calao/tny_a9260/
F: include/configs/tny_a9260.h
CANMB BOARD
-M: -
+#M: -
S: Maintained
F: board/canmb/
F: include/configs/canmb.h
CM-BF527 BOARD
-M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
+#M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
S: Orphan (since 2014-03)
F: board/cm-bf527/
F: include/configs/cm-bf527.h
CM-BF533 BOARD
-M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
+#M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
S: Orphan (since 2014-03)
F: board/cm-bf533/
F: include/configs/cm-bf533.h
CM-BF537E BOARD
-M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
+#M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
S: Orphan (since 2014-03)
F: board/cm-bf537e/
F: include/configs/cm-bf537e.h
CM-BF537U BOARD
-M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
+#M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
S: Orphan (since 2014-03)
F: board/cm-bf537u/
F: include/configs/cm-bf537u.h
CM-BF548 BOARD
-M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
+#M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
S: Orphan (since 2014-03)
F: board/cm-bf548/
F: include/configs/cm-bf548.h
CM-BF561 BOARD
-M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
+#M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
S: Orphan (since 2014-03)
F: board/cm-bf561/
F: include/configs/cm-bf561.h
CM41XX BOARD
-M: -
+#M: -
S: Maintained
F: board/cm41xx/
F: include/configs/cm41xx.h
CM5200 BOARD
-M: -
+#M: -
S: Maintained
F: board/cm5200/
F: include/configs/cm5200.h
CMI BOARD
-M: -
+#M: -
S: Maintained
F: board/cmi/
F: include/configs/cmi_mpc5xx.h
COBRA5272 BOARD
-M: -
+#M: -
S: Maintained
F: board/cobra5272/
F: include/configs/cobra5272.h
--- /dev/null
+if TARGET_CM_FX6
+
+config SYS_CPU
+ string
+ default "armv7"
+
+config SYS_BOARD
+ string
+ default "cm_fx6"
+
+config SYS_VENDOR
+ string
+ default "compulab"
+
+config SYS_SOC
+ string
+ default "mx6"
+
+config SYS_CONFIG_NAME
+ string
+ default "cm_fx6"
+
+endif
--- /dev/null
+CM_FX6 BOARD
+M: Nikita Kiryanov <nikita@compulab.co.il>
+S: Maintained
+F: board/compulab/cm_fx6/
+F: include/configs/cm_fx6.h
+F: configs/cm_fx6_defconfig
--- /dev/null
+#
+# (C) Copyright 2014 CompuLab, Ltd. <www.compulab.co.il>
+#
+# Authors: Nikita Kiryanov <nikita@compulab.co.il>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+ifdef CONFIG_SPL_BUILD
+obj-y = common.o spl.o
+else
+obj-y = common.o cm_fx6.o
+endif
--- /dev/null
+/*
+ * Board functions for Compulab CM-FX6 board
+ *
+ * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Nikita Kiryanov <nikita@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <fdt_support.h>
+#include <sata.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/iomux.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/sata.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include "common.h"
+#include "../common/eeprom.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_DWC_AHSATA
+static int cm_fx6_issd_gpios[] = {
+ /* The order of the GPIOs in the array is important! */
+ CM_FX6_SATA_PHY_SLP,
+ CM_FX6_SATA_NRSTDLY,
+ CM_FX6_SATA_PWREN,
+ CM_FX6_SATA_NSTANDBY1,
+ CM_FX6_SATA_NSTANDBY2,
+ CM_FX6_SATA_LDO_EN,
+};
+
+static void cm_fx6_sata_power(int on)
+{
+ int i;
+
+ if (!on) { /* tell the iSSD that the power will be removed */
+ gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 1);
+ mdelay(10);
+ }
+
+ for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) {
+ gpio_direction_output(cm_fx6_issd_gpios[i], on);
+ udelay(100);
+ }
+
+ if (!on) /* for compatibility lower the power loss interrupt */
+ gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
+}
+
+static iomux_v3_cfg_t const sata_pads[] = {
+ /* SATA PWR */
+ IOMUX_PADS(PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A22__GPIO2_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D20__GPIO3_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ /* SATA CTRL */
+ IOMUX_PADS(PAD_ENET_TXD0__GPIO1_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D23__GPIO3_IO23 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A23__GPIO6_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
+static void cm_fx6_setup_issd(void)
+{
+ SETUP_IOMUX_PADS(sata_pads);
+ /* Make sure this gpio has logical 0 value */
+ gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
+ udelay(100);
+
+ cm_fx6_sata_power(0);
+ mdelay(250);
+ cm_fx6_sata_power(1);
+}
+
+#define CM_FX6_SATA_INIT_RETRIES 10
+int sata_initialize(void)
+{
+ int err, i;
+
+ cm_fx6_setup_issd();
+ for (i = 0; i < CM_FX6_SATA_INIT_RETRIES; i++) {
+ err = setup_sata();
+ if (err) {
+ printf("SATA setup failed: %d\n", err);
+ return err;
+ }
+
+ udelay(100);
+
+ err = __sata_initialize();
+ if (!err)
+ break;
+
+ /* There is no device on the SATA port */
+ if (sata_port_status(0, 0) == 0)
+ break;
+
+ /* There's a device, but link not established. Retry */
+ }
+
+ return err;
+}
+#endif
+
+#ifdef CONFIG_SYS_I2C_MXC
+#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+ PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+I2C_PADS(i2c0_pads,
+ PAD_EIM_D21__I2C1_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ PAD_EIM_D21__GPIO3_IO21 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ IMX_GPIO_NR(3, 21),
+ PAD_EIM_D28__I2C1_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ PAD_EIM_D28__GPIO3_IO28 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ IMX_GPIO_NR(3, 28));
+
+I2C_PADS(i2c1_pads,
+ PAD_KEY_COL3__I2C2_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ PAD_KEY_COL3__GPIO4_IO12 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ IMX_GPIO_NR(4, 12),
+ PAD_KEY_ROW3__I2C2_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ PAD_KEY_ROW3__GPIO4_IO13 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ IMX_GPIO_NR(4, 13));
+
+I2C_PADS(i2c2_pads,
+ PAD_GPIO_3__I2C3_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ PAD_GPIO_3__GPIO1_IO03 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ IMX_GPIO_NR(1, 3),
+ PAD_GPIO_6__I2C3_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ PAD_GPIO_6__GPIO1_IO06 | MUX_PAD_CTRL(I2C_PAD_CTRL),
+ IMX_GPIO_NR(1, 6));
+
+
+static void cm_fx6_setup_i2c(void)
+{
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, I2C_PADS_INFO(i2c0_pads));
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, I2C_PADS_INFO(i2c1_pads));
+ setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, I2C_PADS_INFO(i2c2_pads));
+}
+#else
+static void cm_fx6_setup_i2c(void) { }
+#endif
+
+#ifdef CONFIG_USB_EHCI_MX6
+#define WEAK_PULLDOWN (PAD_CTL_PUS_100K_DOWN | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_HYS | PAD_CTL_SRE_SLOW)
+
+static int cm_fx6_usb_hub_reset(void)
+{
+ int err;
+
+ err = gpio_request(CM_FX6_USB_HUB_RST, "usb hub rst");
+ if (err) {
+ printf("USB hub rst gpio request failed: %d\n", err);
+ return -1;
+ }
+
+ SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL));
+ gpio_direction_output(CM_FX6_USB_HUB_RST, 0);
+ udelay(10);
+ gpio_direction_output(CM_FX6_USB_HUB_RST, 1);
+ mdelay(1);
+
+ return 0;
+}
+
+static int cm_fx6_init_usb_otg(void)
+{
+ int ret;
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ ret = gpio_request(SB_FX6_USB_OTG_PWR, "usb-pwr");
+ if (ret) {
+ printf("USB OTG pwr gpio request failed: %d\n", ret);
+ return ret;
+ }
+
+ SETUP_IOMUX_PAD(PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL));
+ SETUP_IOMUX_PAD(PAD_ENET_RX_ER__USB_OTG_ID |
+ MUX_PAD_CTRL(WEAK_PULLDOWN));
+ clrbits_le32(&iomux->gpr[1], IOMUXC_GPR1_OTG_ID_MASK);
+ /* disable ext. charger detect, or it'll affect signal quality at dp. */
+ return gpio_direction_output(SB_FX6_USB_OTG_PWR, 0);
+}
+
+#define MX6_USBNC_BASEADDR 0x2184800
+#define USBNC_USB_H1_PWR_POL (1 << 9)
+int board_ehci_hcd_init(int port)
+{
+ u32 *usbnc_usb_uh1_ctrl = (u32 *)(MX6_USBNC_BASEADDR + 4);
+
+ switch (port) {
+ case 0:
+ return cm_fx6_init_usb_otg();
+ case 1:
+ SETUP_IOMUX_PAD(PAD_GPIO_0__USB_H1_PWR |
+ MUX_PAD_CTRL(NO_PAD_CTRL));
+
+ /* Set PWR polarity to match power switch's enable polarity */
+ setbits_le32(usbnc_usb_uh1_ctrl, USBNC_USB_H1_PWR_POL);
+ return cm_fx6_usb_hub_reset();
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+int board_ehci_power(int port, int on)
+{
+ if (port == 0)
+ return gpio_direction_output(SB_FX6_USB_OTG_PWR, on);
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+static int mx6_rgmii_rework(struct phy_device *phydev)
+{
+ unsigned short val;
+
+ /* Ar8031 phy SmartEEE feature cause link status generates glitch,
+ * which cause ethernet link down/up issue, so disable SmartEEE
+ */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x3);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x805d);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4003);
+ val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
+ val &= ~(0x1 << 8);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
+
+ /* To enable AR8031 ouput a 125MHz clk from CLK_25M */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+
+ val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
+ val &= 0xffe3;
+ val |= 0x18;
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
+
+ /* introduce tx clock delay */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
+ val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
+ val |= 0x0100;
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
+
+ return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ mx6_rgmii_rework(phydev);
+
+ if (phydev->drv->config)
+ return phydev->drv->config(phydev);
+
+ return 0;
+}
+
+static iomux_v3_cfg_t const enet_pads[] = {
+ IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_GPIO_0__CCM_CLKO1 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_GPIO_3__CCM_CLKO2 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(0x84)),
+ IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK |
+ MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL |
+ MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL |
+ MUX_PAD_CTRL(ENET_PAD_CTRL)),
+};
+
+static int handle_mac_address(void)
+{
+ unsigned char enetaddr[6];
+ int rc;
+
+ rc = eth_getenv_enetaddr("ethaddr", enetaddr);
+ if (rc)
+ return 0;
+
+ rc = cl_eeprom_read_mac_addr(enetaddr);
+ if (rc)
+ return rc;
+
+ if (!is_valid_ether_addr(enetaddr))
+ return -1;
+
+ return eth_setenv_enetaddr("ethaddr", enetaddr);
+}
+
+int board_eth_init(bd_t *bis)
+{
+ int res = handle_mac_address();
+ if (res)
+ puts("No MAC address found\n");
+
+ SETUP_IOMUX_PADS(enet_pads);
+ /* phy reset */
+ gpio_direction_output(CM_FX6_ENET_NRST, 0);
+ udelay(500);
+ gpio_set_value(CM_FX6_ENET_NRST, 1);
+ enable_enet_clk(1);
+ return cpu_eth_init(bis);
+}
+#endif
+
+#ifdef CONFIG_NAND_MXS
+static iomux_v3_cfg_t const nand_pads[] = {
+ IOMUX_PADS(PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
+static void cm_fx6_setup_gpmi_nand(void)
+{
+ SETUP_IOMUX_PADS(nand_pads);
+ /* Enable clock roots */
+ enable_usdhc_clk(1, 3);
+ enable_usdhc_clk(1, 4);
+
+ setup_gpmi_io_clk(MXC_CCM_CS2CDR_ENFC_CLK_PODF(0xf) |
+ MXC_CCM_CS2CDR_ENFC_CLK_PRED(1) |
+ MXC_CCM_CS2CDR_ENFC_CLK_SEL(0));
+}
+#else
+static void cm_fx6_setup_gpmi_nand(void) {}
+#endif
+
+#ifdef CONFIG_FSL_ESDHC
+static struct fsl_esdhc_cfg usdhc_cfg[3] = {
+ {USDHC1_BASE_ADDR},
+ {USDHC2_BASE_ADDR},
+ {USDHC3_BASE_ADDR},
+};
+
+static enum mxc_clock usdhc_clk[3] = {
+ MXC_ESDHC_CLK,
+ MXC_ESDHC2_CLK,
+ MXC_ESDHC3_CLK,
+};
+
+int board_mmc_init(bd_t *bis)
+{
+ int i;
+
+ cm_fx6_set_usdhc_iomux();
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(usdhc_clk[i]);
+ usdhc_cfg[i].max_bus_width = 4;
+ fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ enable_usdhc_clk(1, i);
+ }
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_OF_BOARD_SETUP
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ uint8_t enetaddr[6];
+
+ /* MAC addr */
+ if (eth_getenv_enetaddr("ethaddr", enetaddr)) {
+ fdt_find_and_setprop(blob, "/fec", "local-mac-address",
+ enetaddr, 6, 1);
+ }
+}
+#endif
+
+int board_init(void)
+{
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+ cm_fx6_setup_gpmi_nand();
+ cm_fx6_setup_i2c();
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: CM-FX6\n");
+ return 0;
+}
+
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+
+ switch (gd->ram_size) {
+ case 0x10000000: /* DDR_16BIT_256MB */
+ gd->bd->bi_dram[0].size = 0x10000000;
+ gd->bd->bi_dram[1].size = 0;
+ break;
+ case 0x20000000: /* DDR_32BIT_512MB */
+ gd->bd->bi_dram[0].size = 0x20000000;
+ gd->bd->bi_dram[1].size = 0;
+ break;
+ case 0x40000000:
+ if (is_cpu_type(MXC_CPU_MX6SOLO)) { /* DDR_32BIT_1GB */
+ gd->bd->bi_dram[0].size = 0x20000000;
+ gd->bd->bi_dram[1].size = 0x20000000;
+ } else { /* DDR_64BIT_1GB */
+ gd->bd->bi_dram[0].size = 0x40000000;
+ gd->bd->bi_dram[1].size = 0;
+ }
+ break;
+ case 0x80000000: /* DDR_64BIT_2GB */
+ gd->bd->bi_dram[0].size = 0x40000000;
+ gd->bd->bi_dram[1].size = 0x40000000;
+ break;
+ case 0xEFF00000: /* DDR_64BIT_4GB */
+ gd->bd->bi_dram[0].size = 0x70000000;
+ gd->bd->bi_dram[1].size = 0x7FF00000;
+ break;
+ }
+}
+
+int dram_init(void)
+{
+ gd->ram_size = imx_ddr_size();
+ switch (gd->ram_size) {
+ case 0x10000000:
+ case 0x20000000:
+ case 0x40000000:
+ case 0x80000000:
+ break;
+ case 0xF0000000:
+ gd->ram_size -= 0x100000;
+ break;
+ default:
+ printf("ERROR: Unsupported DRAM size 0x%lx\n", gd->ram_size);
+ return -1;
+ }
+
+ return 0;
+}
+
+u32 get_board_rev(void)
+{
+ return cl_eeprom_get_board_rev();
+}
+
--- /dev/null
+/*
+ * Code used by both U-Boot and SPL for Compulab CM-FX6
+ *
+ * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Nikita Kiryanov <nikita@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <fsl_esdhc.h>
+#include "common.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_FSL_ESDHC
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const usdhc_pads[] = {
+ IOMUX_PADS(PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+
+ IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+
+ IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+};
+
+void cm_fx6_set_usdhc_iomux(void)
+{
+ SETUP_IOMUX_PADS(usdhc_pads);
+}
+
+/* CINS bit doesn't work, so always try to access the MMC card */
+int board_mmc_getcd(struct mmc *mmc)
+{
+ return 1;
+}
+#endif
+
+#ifdef CONFIG_MXC_SPI
+#define ECSPI_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_MED | \
+ PAD_CTL_PUS_100K_DOWN | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const ecspi_pads[] = {
+ IOMUX_PADS(PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(ECSPI_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(ECSPI_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(ECSPI_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(ECSPI_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D19__ECSPI1_SS1 | MUX_PAD_CTRL(ECSPI_PAD_CTRL)),
+};
+
+void cm_fx6_set_ecspi_iomux(void)
+{
+ SETUP_IOMUX_PADS(ecspi_pads);
+}
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+ return (bus == 0 && cs == 0) ? (CM_FX6_ECSPI_BUS0_CS0) : -1;
+}
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Nikita Kiryanov <nikita@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/clock.h>
+
+#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define CM_FX6_ECSPI_BUS0_CS0 IMX_GPIO_NR(2, 30)
+#define CM_FX6_GREEN_LED IMX_GPIO_NR(2, 31)
+#define CM_FX6_ENET_NRST IMX_GPIO_NR(2, 8)
+#define CM_FX6_ENET_NRST IMX_GPIO_NR(2, 8)
+#define CM_FX6_USB_HUB_RST IMX_GPIO_NR(7, 8)
+#define SB_FX6_USB_OTG_PWR IMX_GPIO_NR(3, 22)
+#define CM_FX6_ENET_NRST IMX_GPIO_NR(2, 8)
+#define CM_FX6_USB_HUB_RST IMX_GPIO_NR(7, 8)
+#define SB_FX6_USB_OTG_PWR IMX_GPIO_NR(3, 22)
+#define CM_FX6_SATA_PWREN IMX_GPIO_NR(1, 28)
+#define CM_FX6_SATA_VDDC_CTRL IMX_GPIO_NR(1, 30)
+#define CM_FX6_SATA_LDO_EN IMX_GPIO_NR(2, 16)
+#define CM_FX6_SATA_NSTANDBY1 IMX_GPIO_NR(3, 20)
+#define CM_FX6_SATA_PHY_SLP IMX_GPIO_NR(3, 23)
+#define CM_FX6_SATA_STBY_REQ IMX_GPIO_NR(3, 29)
+#define CM_FX6_SATA_NSTANDBY2 IMX_GPIO_NR(5, 2)
+#define CM_FX6_SATA_NRSTDLY IMX_GPIO_NR(6, 6)
+#define CM_FX6_SATA_PWLOSS_INT IMX_GPIO_NR(6, 31)
+
+
+void cm_fx6_set_usdhc_iomux(void);
+void cm_fx6_set_ecspi_iomux(void);
--- /dev/null
+/*
+ * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+IMAGE_VERSION 2
+BOOT_FROM sd
--- /dev/null
+/*
+ * SPL specific code for Compulab CM-FX6 board
+ *
+ * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Nikita Kiryanov <nikita@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <fsl_esdhc.h>
+#include "common.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+enum ddr_config {
+ DDR_16BIT_256MB,
+ DDR_32BIT_512MB,
+ DDR_32BIT_1GB,
+ DDR_64BIT_1GB,
+ DDR_64BIT_2GB,
+ DDR_64BIT_4GB,
+ DDR_UNKNOWN,
+};
+
+/*
+ * Below DRAM_RESET[DDR_SEL] = 0 which is incorrect according to
+ * Freescale QRM, but this is exactly the value used by the automatic
+ * calibration script and it works also in all our tests, so we leave
+ * it as is at this point.
+ */
+#define CM_FX6_DDR_IOMUX_CFG \
+ .dram_sdqs0 = 0x00000038, \
+ .dram_sdqs1 = 0x00000038, \
+ .dram_sdqs2 = 0x00000038, \
+ .dram_sdqs3 = 0x00000038, \
+ .dram_sdqs4 = 0x00000038, \
+ .dram_sdqs5 = 0x00000038, \
+ .dram_sdqs6 = 0x00000038, \
+ .dram_sdqs7 = 0x00000038, \
+ .dram_dqm0 = 0x00000038, \
+ .dram_dqm1 = 0x00000038, \
+ .dram_dqm2 = 0x00000038, \
+ .dram_dqm3 = 0x00000038, \
+ .dram_dqm4 = 0x00000038, \
+ .dram_dqm5 = 0x00000038, \
+ .dram_dqm6 = 0x00000038, \
+ .dram_dqm7 = 0x00000038, \
+ .dram_cas = 0x00000038, \
+ .dram_ras = 0x00000038, \
+ .dram_sdclk_0 = 0x00000038, \
+ .dram_sdclk_1 = 0x00000038, \
+ .dram_sdcke0 = 0x00003000, \
+ .dram_sdcke1 = 0x00003000, \
+ .dram_reset = 0x00000038, \
+ .dram_sdba2 = 0x00000000, \
+ .dram_sdodt0 = 0x00000038, \
+ .dram_sdodt1 = 0x00000038,
+
+#define CM_FX6_GPR_IOMUX_CFG \
+ .grp_b0ds = 0x00000038, \
+ .grp_b1ds = 0x00000038, \
+ .grp_b2ds = 0x00000038, \
+ .grp_b3ds = 0x00000038, \
+ .grp_b4ds = 0x00000038, \
+ .grp_b5ds = 0x00000038, \
+ .grp_b6ds = 0x00000038, \
+ .grp_b7ds = 0x00000038, \
+ .grp_addds = 0x00000038, \
+ .grp_ddrmode_ctl = 0x00020000, \
+ .grp_ddrpke = 0x00000000, \
+ .grp_ddrmode = 0x00020000, \
+ .grp_ctlds = 0x00000038, \
+ .grp_ddr_type = 0x000C0000,
+
+static struct mx6sdl_iomux_ddr_regs ddr_iomux_s = { CM_FX6_DDR_IOMUX_CFG };
+static struct mx6sdl_iomux_grp_regs grp_iomux_s = { CM_FX6_GPR_IOMUX_CFG };
+static struct mx6dq_iomux_ddr_regs ddr_iomux_q = { CM_FX6_DDR_IOMUX_CFG };
+static struct mx6dq_iomux_grp_regs grp_iomux_q = { CM_FX6_GPR_IOMUX_CFG };
+
+static struct mx6_mmdc_calibration cm_fx6_calib_s = {
+ .p0_mpwldectrl0 = 0x005B0061,
+ .p0_mpwldectrl1 = 0x004F0055,
+ .p0_mpdgctrl0 = 0x0314030C,
+ .p0_mpdgctrl1 = 0x025C0268,
+ .p0_mprddlctl = 0x42464646,
+ .p0_mpwrdlctl = 0x36322C34,
+};
+
+static struct mx6_ddr_sysinfo cm_fx6_sysinfo_s = {
+ .cs1_mirror = 1,
+ .cs_density = 16,
+ .bi_on = 1,
+ .rtt_nom = 1,
+ .rtt_wr = 0,
+ .ralat = 5,
+ .walat = 1,
+ .mif3_mode = 3,
+ .rst_to_cke = 0x23,
+ .sde_to_rst = 0x10,
+};
+
+static struct mx6_ddr3_cfg cm_fx6_ddr3_cfg_s = {
+ .mem_speed = 800,
+ .density = 4,
+ .rowaddr = 14,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1800,
+ .trcmin = 5200,
+ .trasmin = 3600,
+ .SRT = 0,
+};
+
+static void spl_mx6s_dram_init(enum ddr_config dram_config, bool reset)
+{
+ if (reset)
+ ((struct mmdc_p_regs *)MX6_MMDC_P0_MDCTL)->mdmisc = 2;
+
+ switch (dram_config) {
+ case DDR_16BIT_256MB:
+ cm_fx6_sysinfo_s.dsize = 0;
+ cm_fx6_sysinfo_s.ncs = 1;
+ break;
+ case DDR_32BIT_512MB:
+ cm_fx6_sysinfo_s.dsize = 1;
+ cm_fx6_sysinfo_s.ncs = 1;
+ break;
+ case DDR_32BIT_1GB:
+ cm_fx6_sysinfo_s.dsize = 1;
+ cm_fx6_sysinfo_s.ncs = 2;
+ break;
+ default:
+ puts("Tried to setup invalid DDR configuration\n");
+ hang();
+ }
+
+ mx6_dram_cfg(&cm_fx6_sysinfo_s, &cm_fx6_calib_s, &cm_fx6_ddr3_cfg_s);
+ udelay(100);
+}
+
+static struct mx6_mmdc_calibration cm_fx6_calib_q = {
+ .p0_mpwldectrl0 = 0x00630068,
+ .p0_mpwldectrl1 = 0x0068005D,
+ .p0_mpdgctrl0 = 0x04140428,
+ .p0_mpdgctrl1 = 0x037C037C,
+ .p0_mprddlctl = 0x3C30303A,
+ .p0_mpwrdlctl = 0x3A344038,
+ .p1_mpwldectrl0 = 0x0035004C,
+ .p1_mpwldectrl1 = 0x00170026,
+ .p1_mpdgctrl0 = 0x0374037C,
+ .p1_mpdgctrl1 = 0x0350032C,
+ .p1_mprddlctl = 0x30322A3C,
+ .p1_mpwrdlctl = 0x48304A3E,
+};
+
+static struct mx6_ddr_sysinfo cm_fx6_sysinfo_q = {
+ .cs_density = 16,
+ .cs1_mirror = 1,
+ .bi_on = 1,
+ .rtt_nom = 1,
+ .rtt_wr = 0,
+ .ralat = 5,
+ .walat = 1,
+ .mif3_mode = 3,
+ .rst_to_cke = 0x23,
+ .sde_to_rst = 0x10,
+};
+
+static struct mx6_ddr3_cfg cm_fx6_ddr3_cfg_q = {
+ .mem_speed = 1066,
+ .density = 4,
+ .rowaddr = 14,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1324,
+ .trcmin = 59500,
+ .trasmin = 9750,
+ .SRT = 0,
+};
+
+static void spl_mx6q_dram_init(enum ddr_config dram_config, bool reset)
+{
+ if (reset)
+ ((struct mmdc_p_regs *)MX6_MMDC_P0_MDCTL)->mdmisc = 2;
+
+ cm_fx6_ddr3_cfg_q.rowaddr = 14;
+ switch (dram_config) {
+ case DDR_16BIT_256MB:
+ cm_fx6_sysinfo_q.dsize = 0;
+ cm_fx6_sysinfo_q.ncs = 1;
+ break;
+ case DDR_32BIT_512MB:
+ cm_fx6_sysinfo_q.dsize = 1;
+ cm_fx6_sysinfo_q.ncs = 1;
+ break;
+ case DDR_64BIT_1GB:
+ cm_fx6_sysinfo_q.dsize = 2;
+ cm_fx6_sysinfo_q.ncs = 1;
+ break;
+ case DDR_64BIT_2GB:
+ cm_fx6_sysinfo_q.dsize = 2;
+ cm_fx6_sysinfo_q.ncs = 2;
+ break;
+ case DDR_64BIT_4GB:
+ cm_fx6_sysinfo_q.dsize = 2;
+ cm_fx6_sysinfo_q.ncs = 2;
+ cm_fx6_ddr3_cfg_q.rowaddr = 15;
+ break;
+ default:
+ puts("Tried to setup invalid DDR configuration\n");
+ hang();
+ }
+
+ mx6_dram_cfg(&cm_fx6_sysinfo_q, &cm_fx6_calib_q, &cm_fx6_ddr3_cfg_q);
+ udelay(100);
+}
+
+static int cm_fx6_spl_dram_init(void)
+{
+ unsigned long bank1_size, bank2_size;
+
+ switch (get_cpu_type()) {
+ case MXC_CPU_MX6SOLO:
+ mx6sdl_dram_iocfg(64, &ddr_iomux_s, &grp_iomux_s);
+
+ spl_mx6s_dram_init(DDR_32BIT_1GB, false);
+ bank1_size = get_ram_size((long int *)PHYS_SDRAM_1, 0x80000000);
+ if (bank1_size == 0x40000000)
+ return 0;
+
+ if (bank1_size == 0x20000000) {
+ spl_mx6s_dram_init(DDR_32BIT_512MB, true);
+ return 0;
+ }
+
+ spl_mx6s_dram_init(DDR_16BIT_256MB, true);
+ bank1_size = get_ram_size((long int *)PHYS_SDRAM_1, 0x80000000);
+ if (bank1_size == 0x10000000)
+ return 0;
+
+ break;
+ case MXC_CPU_MX6D:
+ case MXC_CPU_MX6Q:
+ mx6dq_dram_iocfg(64, &ddr_iomux_q, &grp_iomux_q);
+
+ spl_mx6q_dram_init(DDR_64BIT_4GB, false);
+ bank1_size = get_ram_size((long int *)PHYS_SDRAM_1, 0x80000000);
+ if (bank1_size == 0x80000000)
+ return 0;
+
+ if (bank1_size == 0x40000000) {
+ bank2_size = get_ram_size((long int *)PHYS_SDRAM_2,
+ 0x80000000);
+ if (bank2_size == 0x40000000) {
+ /* Don't do a full reset here */
+ spl_mx6q_dram_init(DDR_64BIT_2GB, false);
+ } else {
+ spl_mx6q_dram_init(DDR_64BIT_1GB, true);
+ }
+
+ return 0;
+ }
+
+ spl_mx6q_dram_init(DDR_32BIT_512MB, true);
+ bank1_size = get_ram_size((long int *)PHYS_SDRAM_1, 0x80000000);
+ if (bank1_size == 0x20000000)
+ return 0;
+
+ spl_mx6q_dram_init(DDR_16BIT_256MB, true);
+ bank1_size = get_ram_size((long int *)PHYS_SDRAM_1, 0x80000000);
+ if (bank1_size == 0x10000000)
+ return 0;
+
+ break;
+ }
+
+ return -1;
+}
+
+static iomux_v3_cfg_t const uart4_pads[] = {
+ IOMUX_PADS(PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+ IOMUX_PADS(PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+};
+
+static void cm_fx6_setup_uart(void)
+{
+ SETUP_IOMUX_PADS(uart4_pads);
+ enable_uart_clk(1);
+}
+
+#ifdef CONFIG_SPL_SPI_SUPPORT
+static void cm_fx6_setup_ecspi(void)
+{
+ cm_fx6_set_ecspi_iomux();
+ enable_cspi_clock(1, 0);
+}
+#else
+static void cm_fx6_setup_ecspi(void) { }
+#endif
+
+void board_init_f(ulong dummy)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ gd = &gdata;
+ /*
+ * We don't use DMA in SPL, but we do need it in U-Boot. U-Boot
+ * initializes DMA very early (before all board code), so the only
+ * opportunity we have to initialize APBHDMA clocks is in SPL.
+ */
+ setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+ enable_usdhc_clk(1, 2);
+
+ arch_cpu_init();
+ timer_init();
+ cm_fx6_setup_ecspi();
+ cm_fx6_setup_uart();
+ get_clocks();
+ preloader_console_init();
+ gpio_direction_output(CM_FX6_GREEN_LED, 1);
+ if (cm_fx6_spl_dram_init()) {
+ puts("!!!ERROR!!! DRAM detection failed!!!\n");
+ hang();
+ }
+
+ memset(__bss_start, 0, __bss_end - __bss_start);
+ board_init_r(NULL, 0);
+}
+
+void spl_board_init(void)
+{
+ u32 boot_device = spl_boot_device();
+
+ if (boot_device == BOOT_DEVICE_SPI)
+ puts("Booting from SPI flash\n");
+ else if (boot_device == BOOT_DEVICE_MMC1)
+ puts("Booting from MMC\n");
+ else
+ puts("Unknown boot device\n");
+}
+
+#ifdef CONFIG_SPL_MMC_SUPPORT
+static struct fsl_esdhc_cfg usdhc_cfg = {
+ .esdhc_base = USDHC3_BASE_ADDR,
+ .max_bus_width = 4,
+};
+
+int board_mmc_init(bd_t *bis)
+{
+ cm_fx6_set_usdhc_iomux();
+
+ usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+
+ return fsl_esdhc_initialize(bis, &usdhc_cfg);
+}
+#endif
static int cl_eeprom_read(uint offset, uchar *buf, int len)
{
- return i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, offset,
+ int res;
+ unsigned int current_i2c_bus = i2c_get_bus_num();
+
+ res = i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS);
+ if (res < 0)
+ return res;
+
+ res = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, offset,
CONFIG_SYS_I2C_EEPROM_ADDR_LEN, buf, len);
+
+ i2c_set_bus_num(current_i2c_bus);
+
+ return res;
}
static int cl_eeprom_setup_layout(void)
CGTQMX6EVAL BOARD
-M: Leo Sartre <lsartre@adeneo-embedded.com>
+#M: Leo Sartre <lsartre@adeneo-embedded.com>
S: Orphan (since 2014-06)
F: board/congatec/cgtqmx6eval/
F: include/configs/cgtqmx6eval.h
CPU87 BOARD
-M: -
+#M: -
S: Maintained
F: board/cpu87/
F: include/configs/CPU87.h
L1 BOARD
-M: David Updegraff <dave@cray.com>
+#M: David Updegraff <dave@cray.com>
S: Orphan (since 2014-03)
F: board/cray/L1/
F: include/configs/CRAYL1.h
PPCHAMELEONEVB BOARD
-M: -
+#M: -
S: Maintained
F: board/dave/PPChameleonEVB/
F: include/configs/CATcenter.h
DM355EVM BOARD
-M: Sandeep Paulraj <s-paulraj@ti.com>
+#M: Sandeep Paulraj <s-paulraj@ti.com>
S: Orphan (since 2014-08)
F: board/davinci/dm355evm/
F: include/configs/davinci_dm355evm.h
DM355LEOPARD BOARD
-M: Sandeep Paulraj <s-paulraj@ti.com>
+#M: Sandeep Paulraj <s-paulraj@ti.com>
S: Orphan (since 2014-08)
F: board/davinci/dm355leopard/
F: include/configs/davinci_dm355leopard.h
DM365EVM BOARD
-M: Sandeep Paulraj <s-paulraj@ti.com>
+#M: Sandeep Paulraj <s-paulraj@ti.com>
S: Orphan (since 2014-08)
F: board/davinci/dm365evm/
F: include/configs/davinci_dm365evm.h
DM6467EVM BOARD
-M: Sandeep Paulraj <s-paulraj@ti.com>
+#M: Sandeep Paulraj <s-paulraj@ti.com>
S: Orphan (since 2014-08)
F: board/davinci/dm6467evm/
F: include/configs/davinci_dm6467evm.h
DVEVM BOARD
-M: -
+#M: -
S: Maintained
F: board/davinci/dvevm/
F: include/configs/davinci_dvevm.h
SCHMOOGIE BOARD
-M: -
+#M: -
S: Maintained
F: board/davinci/schmoogie/
F: include/configs/davinci_schmoogie.h
SFFSDR BOARD
-M: -
+#M: -
S: Maintained
F: board/davinci/sffsdr/
F: include/configs/davinci_sffsdr.h
SONATA BOARD
-M: -
+#M: -
S: Maintained
F: board/davinci/sonata/
F: include/configs/davinci_sonata.h
FAVR-32-EZKIT BOARD
-M: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
+#M: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
S: Orphan (since 2014-06)
F: board/earthlcd/favr-32-ezkit/
F: include/configs/favr-32-ezkit.h
ELPPC BOARD
-M: -
+#M: -
S: Maintained
F: board/eltec/elppc/
F: include/configs/ELPPC.h
+++ /dev/null
-/*
- * (C) Copyright 2001-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+ return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1;
+}
+
static void setup_spi(void)
{
imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+++ /dev/null
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
EP8260 BOARD
-M: Frank Panno <fpanno@delphintech.com>
+#M: Frank Panno <fpanno@delphintech.com>
S: Orphan (since 2014-06)
F: board/ep8260/
F: include/configs/ep8260.h
EP82XXM BOARD
-M: -
+#M: -
S: Maintained
F: board/ep82xxm/
F: include/configs/ep82xxm.h
IMA3-MX53 BOARD
-M: -
+#M: -
S: Maintained
F: board/esg/ima3-mx53/
F: include/configs/ima3-mx53.h
ESPT BOARD
-M: -
+#M: -
S: Maintained
F: board/espt/
F: include/configs/espt.h
F: configs/P3G4_defconfig
ZUMA BOARD
-M: Nye Liu <nyet@zumanetworks.com>
+#M: Nye Liu <nyet@zumanetworks.com>
S: Orphan (since 2014-04)
F: include/configs/ZUMA.h
F: configs/ZUMA_defconfig
HWW1U1A BOARD
-M: Kyle Moffett <Kyle.D.Moffett@boeing.com>
+#M: Kyle Moffett <Kyle.D.Moffett@boeing.com>
S: Orphan (since 2014-06)
F: board/exmeritus/hww1u1a/
F: include/configs/HWW1U1A.h
B4860QDS BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/b4860qds/
F: include/configs/B4860QDS.h
continue;
/* Calculate the temp out frequency */
tmp_out = input_freq * 2 * vdw / (rdw * od * 1000);
- diff = MAX(out_freq, tmp_out) - MIN(out_freq, tmp_out);
+ diff = max(out_freq, tmp_out) - min(out_freq, tmp_out);
/*
* calculate the percent, the precision is 1/1000
* If greater than 1/1000, continue
CORENET_DS BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/corenet_ds/
F: include/configs/P3041DS.h
F: board/freescale/ls1021aqds/
F: include/configs/ls1021aqds.h
F: configs/ls1021aqds_nor_defconfig
+F: configs/ls1021aqds_ddr4_nor_defconfig
*/
popts->wrlvl_override = 1;
popts->wrlvl_sample = 0xf;
- popts->cswl_override = DDR_CSWL_CS0;
/*
* Rtt and Rtt_WR override
/* Enable ZQ calibration */
popts->zq_en = 1;
+#ifdef CONFIG_SYS_FSL_DDR4
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+ DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
+#else
+ popts->cswl_override = DDR_CSWL_CS0;
+
/* DHC_EN =1, ODT = 75 Ohm */
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+#endif
}
#ifdef CONFIG_SYS_DDR_RAW_TIMING
* num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
* ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
*/
+#ifdef CONFIG_SYS_FSL_DDR4
+ {2, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,},
+ {2, 1900, 0, 4, 6, 0x08080A0C, 0x0D0E0F0A,},
+ {1, 1666, 0, 4, 8, 0x090A0B0B, 0x0C0D0E0C,},
+ {1, 1900, 0, 4, 9, 0x0A0B0C0B, 0x0D0E0F0D,},
+ {1, 2200, 0, 4, 10, 0x0B0C0D0C, 0x0E0F110E,},
+#elif defined(CONFIG_SYS_FSL_DDR3)
{1, 833, 1, 6, 8, 0x06060607, 0x08080807, 0x1f, 2, 0},
{1, 1350, 1, 6, 8, 0x0708080A, 0x0A0B0C09, 0x1f, 2, 0},
{1, 833, 2, 6, 8, 0x06060607, 0x08080807, 0x1f, 2, 0},
{2, 1350, 0, 6, 8, 0x0708080A, 0x0A0B0C09, 0x1f, 2, 0},
{2, 1666, 4, 4, 0xa, 0x0B08090C, 0x0B0E0D0A, 0x1f, 2, 0},
{2, 1666, 0, 4, 0xa, 0x0B08090C, 0x0B0E0D0A, 0x1f, 2, 0},
+#else
+#error DDR type not defined
+#endif
{}
};
if TARGET_LS2085A_EMU
-config SYS_CPU
- default "armv8"
-
config SYS_BOARD
default "ls2085a"
if TARGET_LS2085A_SIMU
-config SYS_CPU
- default "armv8"
-
config SYS_BOARD
default "ls2085a"
* to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
*/
if (popts->registered_dimm_en)
- pbsp = rdimms[0];
+ pbsp = rdimms[ctrl_num];
else
- pbsp = udimms[0];
+ pbsp = udimms[ctrl_num];
/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
pbsp->wrlvl_ctl_3);
+ if (ctrl_num == CONFIG_DP_DDR_CTRL) {
+ /* force DDR bus width to 32 bits */
+ popts->data_bus_width = 1;
+ popts->otf_burst_chop_en = 0;
+ popts->burst_length = DDR_BL8;
+ }
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
void dram_init_banksize(void)
{
+#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
+ phys_size_t dp_ddr_size;
+#endif
+
gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
} else {
gd->bd->bi_dram[0].size = gd->ram_size;
}
+
+#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
+ /* initialize DP-DDR here */
+ puts("DP-DDR: ");
+ /*
+ * DDR controller use 0 as the base address for binding.
+ * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
+ */
+ dp_ddr_size = fsl_other_ddr_sdram(CONFIG_SYS_DP_DDR_BASE_PHY,
+ CONFIG_DP_DDR_CTRL,
+ CONFIG_DP_DDR_NUM_CTRLS,
+ CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR,
+ NULL, NULL, NULL);
+ if (dp_ddr_size) {
+ gd->bd->bi_dram[2].start = CONFIG_SYS_DP_DDR_BASE;
+ gd->bd->bi_dram[2].size = dp_ddr_size;
+ } else {
+ puts("Not detected");
+ }
+#endif
}
{}
};
+/* DP-DDR DIMM */
+static const struct board_specific_parameters udimm2[] = {
+ /*
+ * memory controller 2
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3
+ */
+ {2, 2140, 0, 4, 4, 0x0, 0x0},
+ {1, 2140, 0, 4, 4, 0x0, 0x0},
+ {}
+};
+
static const struct board_specific_parameters rdimm0[] = {
/*
* memory controller 0
{}
};
+/* DP-DDR DIMM */
+static const struct board_specific_parameters rdimm2[] = {
+ /*
+ * memory controller 2
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3
+ */
+ {4, 2140, 0, 5, 4, 0x0, 0x0},
+ {2, 2140, 0, 5, 4, 0x0, 0x0},
+ {1, 2140, 0, 4, 4, 0x0, 0x0},
+ {}
+};
+
static const struct board_specific_parameters *udimms[] = {
udimm0,
+ udimm0,
+ udimm2,
};
static const struct board_specific_parameters *rdimms[] = {
rdimm0,
+ rdimm0,
+ rdimm2,
};
#include <fdt_support.h>
#include <libfdt.h>
#include <fsl_mc.h>
+#include <environment.h>
DECLARE_GLOBAL_DATA_PTR;
int board_init(void)
{
init_final_memctl_regs();
+
+#ifdef CONFIG_ENV_IS_NOWHERE
+ gd->env_addr = (ulong)&default_environment[0];
+#endif
+
return 0;
}
return 0;
}
+void detail_board_ddr_info(void)
+{
+ puts("\nDDR ");
+ print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
+ print_ddr_info(0);
+ if (gd->bd->bi_dram[2].size) {
+ puts("\nDP-DDR ");
+ print_size(gd->bd->bi_dram[2].size, "");
+ print_ddr_info(CONFIG_DP_DDR_CTRL);
+ }
+}
+
int dram_init(void)
{
- printf("DRAM: ");
gd->ram_size = initdram(0);
return 0;
phys_addr_t base;
phys_size_t size;
+ ft_cpu_setup(blob, bd);
+
/* limit the memory size to bank 1 until Linux can handle 40-bit PA */
base = getenv_bootm_low();
size = getenv_bootm_size();
M5208EVBE BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/m5208evbe/
F: include/configs/M5208EVBE.h
M5249EVB BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/m5249evb/
F: include/configs/M5249EVB.h
M5253EVBE BOARD
-M: Hayden Fraser <Hayden.Fraser@freescale.com>
+#M: Hayden Fraser <Hayden.Fraser@freescale.com>
S: Orphan (since 2014-06)
F: board/freescale/m5253evbe/
F: include/configs/M5253EVBE.h
M5272C3 BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/m5272c3/
F: include/configs/M5272C3.h
M5275EVB BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/m5275evb/
F: include/configs/M5275EVB.h
M5282EVB BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/m5282evb/
F: include/configs/M5282EVB.h
M54418TWR BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/m54418twr/
F: include/configs/M54418TWR.h
M54451EVB BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/m54451evb/
F: include/configs/M54451EVB.h
MPC5121ADS BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/mpc5121ads/
F: include/configs/mpc5121ads.h
MPC8313ERDB BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/mpc8313erdb/
F: include/configs/MPC8313ERDB.h
MPC8349ITX BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/mpc8349itx/
F: include/configs/MPC8349ITX.h
MPC8360ERDK BOARD
-
M: Anton Vorontsov <avorontsov@ru.mvista.com>
+
#M: Anton Vorontsov <avorontsov@ru.mvista.com>
S: Orphan (since 2014-03)
F: board/freescale/mpc8360erdk/
F: include/configs/MPC8360ERDK.h
MPC837XERDB BOARD
-M: Joe D'Abbraccio <ljd015@freescale.com>
+#M: Joe D'Abbraccio <ljd015@freescale.com>
S: Orphan (since 2014-06)
F: board/freescale/mpc837xerdb/
F: include/configs/MPC837XERDB.h
MPC8536DS BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/mpc8536ds/
F: include/configs/MPC8536DS.h
MPC8540ADS BOARD
-M: Kumar Gala <kumar.gala@freescale.com>
+#M: Kumar Gala <kumar.gala@freescale.com>
S: Orphan (since 2014-06)
F: board/freescale/mpc8540ads/
F: include/configs/MPC8540ADS.h
MPC8541CDS BOARD
-M: Kumar Gala <kumar.gala@freescale.com>
+#M: Kumar Gala <kumar.gala@freescale.com>
S: Orphan (since 2014-06)
F: board/freescale/mpc8541cds/
F: include/configs/MPC8541CDS.h
MPC8544DS BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/mpc8544ds/
F: include/configs/MPC8544DS.h
MPC8548CDS BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/mpc8548cds/
F: include/configs/MPC8548CDS.h
MPC8555CDS BOARD
-M: Kumar Gala <kumar.gala@freescale.com>
+#M: Kumar Gala <kumar.gala@freescale.com>
S: Orphan (since 2014-06)
F: board/freescale/mpc8555cds/
F: include/configs/MPC8555CDS.h
MPC8560ADS BOARD
-M: Kumar Gala <kumar.gala@freescale.com>
+#M: Kumar Gala <kumar.gala@freescale.com>
S: Orphan (since 2014-06)
F: board/freescale/mpc8560ads/
F: include/configs/MPC8560ADS.h
MPC8568MDS BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/mpc8568mds/
F: include/configs/MPC8568MDS.h
MPC8569MDS BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/mpc8569mds/
F: include/configs/MPC8569MDS.h
MPC8610HPCD BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/mpc8610hpcd/
F: include/configs/MPC8610HPCD.h
MPC8641HPCN BOARD
-M: Kumar Gala <kumar.gala@freescale.com>
+#M: Kumar Gala <kumar.gala@freescale.com>
S: Orphan (since 2014-06)
F: board/freescale/mpc8641hpcn/
F: include/configs/MPC8641HPCN.h
MX31ADS BOARD
-M: (resigned) Guennadi Liakhovetski <g.liakhovetski@gmx.de>
+#M: (resigned) Guennadi Liakhovetski <g.liakhovetski@gmx.de>
S: Orphan (since 2013-09)
F: board/freescale/mx31ads/
F: include/configs/mx31ads.h
return 0;
}
+#ifdef CONFIG_MXC_SPI
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+ return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 9)) : -1;
+}
+#endif
+
#ifdef CONFIG_CMD_BMODE
static const struct boot_mode board_boot_modes[] = {
/* 4 bit bus width */
--- /dev/null
+/*
+ * Copyright (C) 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi, sd (the board has no nand neither onenand)
+ */
+
+BOOT_FROM sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+DATA 4 0x020e0774 0x000C0000
+DATA 4 0x020e0754 0x00000000
+DATA 4 0x020e04ac 0x00000030
+DATA 4 0x020e04b0 0x00000030
+DATA 4 0x020e0464 0x00000030
+DATA 4 0x020e0490 0x00000030
+DATA 4 0x020e074c 0x00000030
+DATA 4 0x020e0494 0x00000030
+DATA 4 0x020e04a0 0x00000000
+DATA 4 0x020e04b4 0x00000030
+DATA 4 0x020e04b8 0x00000030
+DATA 4 0x020e076c 0x00000030
+DATA 4 0x020e0750 0x00020000
+DATA 4 0x020e04bc 0x00000030
+DATA 4 0x020e04c0 0x00000030
+DATA 4 0x020e04c4 0x00000030
+DATA 4 0x020e04c8 0x00000030
+DATA 4 0x020e04cc 0x00000030
+DATA 4 0x020e04d0 0x00000030
+DATA 4 0x020e04d4 0x00000030
+DATA 4 0x020e04d8 0x00000030
+DATA 4 0x020e0760 0x00020000
+DATA 4 0x020e0764 0x00000030
+DATA 4 0x020e0770 0x00000030
+DATA 4 0x020e0778 0x00000030
+DATA 4 0x020e077c 0x00000030
+DATA 4 0x020e0780 0x00000030
+DATA 4 0x020e0784 0x00000030
+DATA 4 0x020e078c 0x00000030
+DATA 4 0x020e0748 0x00000030
+DATA 4 0x020e0470 0x00000030
+DATA 4 0x020e0474 0x00000030
+DATA 4 0x020e0478 0x00000030
+DATA 4 0x020e047c 0x00000030
+DATA 4 0x020e0480 0x00000030
+DATA 4 0x020e0484 0x00000030
+DATA 4 0x020e0488 0x00000030
+DATA 4 0x020e048c 0x00000030
+DATA 4 0x021b0800 0xa1390003
+DATA 4 0x021b080c 0x001F001F
+DATA 4 0x021b0810 0x001F001F
+DATA 4 0x021b480c 0x001F001F
+DATA 4 0x021b4810 0x001F001F
+DATA 4 0x021b083c 0x4220021F
+DATA 4 0x021b0840 0x0207017E
+DATA 4 0x021b483c 0x4201020C
+DATA 4 0x021b4840 0x01660172
+DATA 4 0x021b0848 0x4A4D4E4D
+DATA 4 0x021b4848 0x4A4F5049
+DATA 4 0x021b0850 0x3F3C3D31
+DATA 4 0x021b4850 0x3238372B
+DATA 4 0x021b081c 0x33333333
+DATA 4 0x021b0820 0x33333333
+DATA 4 0x021b0824 0x33333333
+DATA 4 0x021b0828 0x33333333
+DATA 4 0x021b481c 0x33333333
+DATA 4 0x021b4820 0x33333333
+DATA 4 0x021b4824 0x33333333
+DATA 4 0x021b4828 0x33333333
+DATA 4 0x021b08b8 0x00000800
+DATA 4 0x021b48b8 0x00000800
+DATA 4 0x021b0004 0x0002002D
+DATA 4 0x021b0008 0x00333030
+DATA 4 0x021b000c 0x3F435313
+DATA 4 0x021b0010 0xB66E8B63
+DATA 4 0x021b0014 0x01FF00DB
+DATA 4 0x021b0018 0x00001740
+DATA 4 0x021b001c 0x00008000
+DATA 4 0x021b002c 0x000026d2
+DATA 4 0x021b0030 0x00431023
+DATA 4 0x021b0040 0x00000027
+DATA 4 0x021b0000 0x831A0000
+DATA 4 0x021b001c 0x04008032
+DATA 4 0x021b001c 0x00008033
+DATA 4 0x021b001c 0x00048031
+DATA 4 0x021b001c 0x05208030
+DATA 4 0x021b001c 0x04008040
+DATA 4 0x021b0020 0x00005800
+DATA 4 0x021b0818 0x00011117
+DATA 4 0x021b4818 0x00011117
+DATA 4 0x021b0004 0x0002556D
+DATA 4 0x021b0404 0x00011006
+DATA 4 0x021b001c 0x00000000
+
+/* set the default clock gate to save power */
+DATA 4 0x020c4068 0x00C03F3F
+DATA 4 0x020c406c 0x0030FC03
+DATA 4 0x020c4070 0x0FFFC000
+DATA 4 0x020c4074 0x3FF00000
+DATA 4 0x020c4078 0x00FFF300
+DATA 4 0x020c407c 0x0F0000C3
+DATA 4 0x020c4080 0x000003FF
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4 0x020e0010 0xF00000CF
+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+DATA 4 0x020e0018 0x007F007F
+DATA 4 0x020e001c 0x007F007F
return 0;
}
+#ifdef CONFIG_MXC_SPI
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+ return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 9)) : -1;
+}
+#endif
+
#ifdef CONFIG_CMD_BMODE
static const struct boot_mode board_boot_modes[] = {
/* 4 bit bus width */
MX6_PAD_ECSPI1_SS0__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+ return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 11)) : -1;
+}
+
static void setup_spi(void)
{
imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
P1010RDB BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/p1010rdb/
F: include/configs/P1010RDB.h
P1023RDB BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/p1023rdb/
F: include/configs/P1023RDB.h
P1_P2_RDB BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/p1_p2_rdb/
F: include/configs/P1_P2_RDB.h
P1_P2_RDB_PC BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/p1_p2_rdb_pc/
F: include/configs/p1_p2_rdb_pc.h
P1_TWR BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/p1_twr/
F: include/configs/p1_twr.h
P2020DS BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/p2020ds/
F: include/configs/P2020DS.h
P2041RDB BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/p2041rdb/
F: include/configs/P2041RDB.h
break;
case 0xA7:
lane_to_slot[1] = 7;
+ lane_to_slot[2] = 6;
+ lane_to_slot[3] = 5;
lane_to_slot[7] = 7;
break;
case 0xAA:
fm_info_set_phy_address(i, riser_phy_addr[1]);
if (FM1_DTSEC3 == i)
fm_info_set_phy_address(i, riser_phy_addr[2]);
+ if (FM1_DTSEC5 == i)
+ fm_info_set_phy_address(i, riser_phy_addr[3]);
mdio_mux[i] = EMI1_SLOT7;
fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
F: configs/T1040RDB_defconfig
F: configs/T1040RDB_NAND_defconfig
F: configs/T1040RDB_SPIFLASH_defconfig
+F: configs/T1042RDB_defconfig
F: configs/T1042RDB_PI_defconfig
F: configs/T1042RDB_PI_NAND_defconfig
F: configs/T1042RDB_PI_SPIFLASH_defconfig
T1040RDB_SDCARD BOARD
-M: -
+#M: -
S: Maintained
F: configs/T1040RDB_SDCARD_defconfig
F: configs/T1042RDB_PI_SDCARD_defconfig
(and variants). Variants inclued T1042 presonality of T1040, in which
case T1040RDB can also be called T1042RDB.
+The T1042RDB is a Freescale reference board that hosts the T1042 SoC
+(and variants). The board is similar to T1040RDB, T1040 is a reduced
+personality of T1040 SoC without Integrated 8-port Gigabit(L2 Switch).
+
The T1042RDB_PI is a Freescale reference board that hosts the T1042 SoC.
(a personality of T1040 SoC). The board is similar to T1040RDB but is
designed specially with low power features targeted for Printing Image Market.
+Basic difference's among T1040RDB, T1042RDB_PI, T1042RDB
+-------------------------------------------------------------------------
+Board Si Protocol Targeted Market
+-------------------------------------------------------------------------
+T1040RDB T1040 0x66 Networking
+T1040RDB T1042 0x86 Networking
+T1042RDB_PI T1042 0x06 Printing & Imaging
+
+
T1040 SoC Overview
------------------
The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
Commands for switching to alternate bank.
1. To change from vbank0 to vbank4
- => qixis_reset altbank (it will boot using vbank4)
+ => cpld reset altbank (it will boot using vbank4)
2.To change from vbank4 to vbank0
- => qixis reset (it will boot using vbank0)
+ => cpld reset (it will boot using vbank0)
NAND boot with 2 Stage boot loader
----------------------------------
===============
NAND boot SW setting:
SW1: 10001000
-SW2: 00111001
+SW2: 00111011
SW3: 11110001
SPI boot SW setting:
SW1: 00100010
-SW2: 10111001
+SW2: 10111011
SW3: 11100001
SD boot SW setting:
SW1: 00100000
-SW2: 00111001
+SW2: 00111011
SW3: 11100001
popts->zq_en = 1;
/* DHC_EN =1, ODT = 75 Ohm */
- popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_OFF);
- popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_OFF);
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
}
phys_size_t initdram(int board_type)
fm_info_set_phy_address(FM1_DTSEC3,
CONFIG_SYS_SGMII1_PHY_ADDR);
break;
+#endif
+#ifdef CONFIG_T1042RDB
+ case PHY_INTERFACE_MODE_SGMII:
+ /* T1042RDB doesn't supports SGMII on DTSEC1 & DTSEC2 */
+ if ((FM1_DTSEC1 == i) || (FM1_DTSEC2 == i))
+ fm_info_set_phy_address(i, 0);
+ /* T1042RDB only supports SGMII on DTSEC3 */
+ fm_info_set_phy_address(FM1_DTSEC3,
+ CONFIG_SYS_SGMII1_PHY_ADDR);
+ break;
#endif
case PHY_INTERFACE_MODE_RGMII:
if (FM1_DTSEC4 == i)
--- /dev/null
+#PBL preamble and RCW header
+aa55aa55 010e0100
+# serdes protocol 0x06
+0c18000e 0e000000 00000000 00000000
+06000002 00400002 e8106000 01000000
+00000000 00000000 00000000 00030810
+00000000 01fe0a06 00000000 00000000
#PBL preamble and RCW header
aa55aa55 010e0100
-# serdes protocol 0x66
+# serdes protocol 0x86
0c18000e 0e000000 00000000 00000000
-06000002 00400002 e8106000 01000000
-00000000 00000000 00000000 00030810
-00000000 01fe0a06 00000000 00000000
+86000002 80000002 ec027000 01000000
+00000000 00000000 00000000 00032810
+00000000 0342500f 00000000 00000000
T208XQDS BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/t208xqds/
F: include/configs/T208xQDS.h
T208XRDB BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/t208xrdb/
F: include/configs/T208xRDB.h
T4QDS BOARD
-M: -
+#M: -
S: Maintained
F: board/freescale/t4qds/
F: include/configs/T4240QDS.h
VOVPN-GW BOARD
-M: -
+#M: -
S: Maintained
F: board/funkwerk/vovpn-gw/
F: include/configs/VoVPN-GW.h
GR_CPCI_AX2000 BOARD
-M: -
+#M: -
S: Maintained
F: board/gaisler/gr_cpci_ax2000/
F: include/configs/gr_cpci_ax2000.h
GR_EP2S60 BOARD
-M: -
+#M: -
S: Maintained
F: board/gaisler/gr_ep2s60/
F: include/configs/gr_ep2s60.h
GR_XC3S_1500 BOARD
-M: -
+#M: -
S: Maintained
F: board/gaisler/gr_xc3s_1500/
F: include/configs/gr_xc3s_1500.h
GRSIM BOARD
-M: -
+#M: -
S: Maintained
F: board/gaisler/grsim/
F: include/configs/grsim.h
GRSIM_LEON2 BOARD
-M: -
+#M: -
S: Maintained
F: board/gaisler/grsim_leon2/
F: include/configs/grsim_leon2.h
GALAXY5200 BOARD
-M: Eric Millbrandt <emillbrandt@dekaresearch.com>
+#M: Eric Millbrandt <emillbrandt@dekaresearch.com>
S: Orphan (since 2014-06)
F: board/galaxy5200/
F: include/configs/galaxy5200.h
case '4':
type = GW54xx;
break;
+ case '5':
+ type = GW552x;
+ break;
default:
printf("EEPROM: Unknown model in EEPROM: %s\n", info->model);
type = GW_UNKNOWN;
read_hwmon("VDD_SOC", GSC_HWMON_VDD_SOC, 3, MINMAX(1375, 10));
read_hwmon("VDD_1P0", GSC_HWMON_VDD_1P0, 3, MINMAX(1000, 10));
break;
+ case '5': /* GW55xx */
+ read_hwmon("VDD_CORE", GSC_HWMON_VDD_CORE, 3, MINMAX(1175, 10));
+ read_hwmon("VDD_SOC", GSC_HWMON_VDD_SOC, 3, MINMAX(1175, 10));
+ break;
}
return 0;
}
#include <mmc.h>
#include <mtd_node.h>
#include <netdev.h>
+#include <pci.h>
#include <power/pmic.h>
#include <power/ltc3676_pmic.h>
#include <power/pfuze100_pmic.h>
/* Reset USB HUB (present on GW54xx/GW53xx) */
switch (info->model[3]) {
case '3': /* GW53xx */
+ case '5': /* GW552x */
SETUP_IOMUX_PAD(PAD_GPIO_9__GPIO1_IO09 | DIO_PAD_CFG);
gpio_direction_output(IMX_GPIO_NR(1, 9), 0);
mdelay(2);
IOMUX_PADS(PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
};
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+ return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -1;
+}
+
static void setup_spi(void)
{
- gpio_direction_output(CONFIG_SF_DEFAULT_CS, 1);
+ gpio_direction_output(IMX_GPIO_NR(3, 19), 1);
SETUP_IOMUX_PADS(ecspi1_pads);
}
#endif
setup_iomux_enet();
#ifdef CONFIG_FEC_MXC
- cpu_eth_init(bis);
+ if (board_type != GW552x)
+ cpu_eth_init(bis);
#endif
#ifdef CONFIG_CI_UDC
IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | DIO_PAD_CFG),
/* PANLEDR# */
IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | DIO_PAD_CFG),
+ /* MX6_LOCLED# */
+ IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | DIO_PAD_CFG),
/* IOEXP_PWREN# */
IOMUX_PADS(PAD_EIM_A19__GPIO2_IO19 | DIO_PAD_CFG),
/* IOEXP_IRQ# */
IOMUX_PADS(PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(IRQ_PAD_CTRL)),
/* DIOI2C_DIS# */
IOMUX_PADS(PAD_GPIO_19__GPIO4_IO05 | DIO_PAD_CFG),
-
- /* MX6_LOCLED# */
- IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | DIO_PAD_CFG),
/* GPS_SHDN */
IOMUX_PADS(PAD_ENET_RXD0__GPIO1_IO27 | DIO_PAD_CFG),
/* VID_EN */
IOMUX_PADS(PAD_DISP0_DAT23__GPIO5_IO17 | DIO_PAD_CFG),
};
+static iomux_v3_cfg_t const gw552x_gpio_pads[] = {
+ /* PANLEDG# */
+ IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | DIO_PAD_CFG),
+ /* PANLEDR# */
+ IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | DIO_PAD_CFG),
+ /* MX6_LOCLED# */
+ IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | DIO_PAD_CFG),
+ /* PCI_RST# */
+ IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | DIO_PAD_CFG),
+ /* MX6_DIO[4:9] */
+ IOMUX_PADS(PAD_CSI0_PIXCLK__GPIO5_IO18 | DIO_PAD_CFG),
+ IOMUX_PADS(PAD_CSI0_DATA_EN__GPIO5_IO20 | DIO_PAD_CFG),
+ IOMUX_PADS(PAD_CSI0_VSYNC__GPIO5_IO21 | DIO_PAD_CFG),
+ IOMUX_PADS(PAD_CSI0_DAT4__GPIO5_IO22 | DIO_PAD_CFG),
+ IOMUX_PADS(PAD_CSI0_DAT5__GPIO5_IO23 | DIO_PAD_CFG),
+ IOMUX_PADS(PAD_CSI0_DAT7__GPIO5_IO25 | DIO_PAD_CFG),
+ /* PCIEGBE1_OFF# */
+ IOMUX_PADS(PAD_GPIO_1__GPIO1_IO01 | DIO_PAD_CFG),
+ /* PCIEGBE2_OFF# */
+ IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | DIO_PAD_CFG),
+ /* PCIESKT_WDIS# */
+ IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | DIO_PAD_CFG),
+};
+
/*
* each baseboard has 4 user configurable Digital IO lines which can
* be pinmuxed as a GPIO or in some cases a PWM
.pcie_sson = IMX_GPIO_NR(1, 20),
.wdis = IMX_GPIO_NR(5, 17),
},
+
+ /* GW552x */
+ {
+ .gpio_pads = gw552x_gpio_pads,
+ .num_pads = ARRAY_SIZE(gw552x_gpio_pads)/2,
+ .dio_cfg = {
+ {
+ { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
+ IMX_GPIO_NR(1, 16),
+ { 0, 0 },
+ 0
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+ IMX_GPIO_NR(1, 19),
+ { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+ 2
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
+ IMX_GPIO_NR(1, 17),
+ { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
+ 3
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
+ IMX_GPIO_NR(2, 10),
+ { 0, 0 },
+ 0
+ },
+ },
+ .leds = {
+ IMX_GPIO_NR(4, 6),
+ IMX_GPIO_NR(4, 7),
+ IMX_GPIO_NR(4, 15),
+ },
+ .pcie_rst = IMX_GPIO_NR(1, 29),
+ },
};
/* setup board specific PMIC */
#endif
/* turn off (active-high) user LED's */
- for (i = 0; i < 4; i++) {
+ for (i = 0; i < ARRAY_SIZE(gpio_cfg[board].leds); i++) {
if (gpio_cfg[board].leds[i])
gpio_direction_output(gpio_cfg[board].leds[i], 1);
}
/* Expansion Mezzanine IO */
- gpio_direction_output(gpio_cfg[board].mezz_pwren, 0);
- gpio_direction_input(gpio_cfg[board].mezz_irq);
+ if (gpio_cfg[board].mezz_pwren)
+ gpio_direction_output(gpio_cfg[board].mezz_pwren, 0);
+ if (gpio_cfg[board].mezz_irq)
+ gpio_direction_input(gpio_cfg[board].mezz_irq);
/* RS485 Transmit Enable */
if (gpio_cfg[board].rs485en)
}
return 0;
}
+
+/*
+ * Most Ventana boards have a PLX PEX860x PCIe switch onboard and use its
+ * GPIO's as PERST# signals for its downstream ports - configure the GPIO's
+ * properly and assert reset for 100ms.
+ */
+void board_pci_fixup_dev(struct pci_controller *hose, pci_dev_t dev,
+ unsigned short vendor, unsigned short device,
+ unsigned short class)
+{
+ u32 dw;
+
+ debug("%s: %02d:%02d.%02d: %04x:%04x\n", __func__,
+ PCI_BUS(dev), PCI_DEV(dev), PCI_FUNC(dev), vendor, device);
+ if (vendor == PCI_VENDOR_ID_PLX &&
+ (device & 0xfff0) == 0x8600 &&
+ PCI_DEV(dev) == 0 && PCI_FUNC(dev) == 0) {
+ debug("configuring PLX 860X downstream PERST#\n");
+ pci_hose_read_config_dword(hose, dev, 0x62c, &dw);
+ dw |= 0xaaa8; /* GPIO1-7 outputs */
+ pci_hose_write_config_dword(hose, dev, 0x62c, dw);
+
+ pci_hose_read_config_dword(hose, dev, 0x644, &dw);
+ dw |= 0xfe; /* GPIO1-7 output high */
+ pci_hose_write_config_dword(hose, dev, 0x644, dw);
+
+ mdelay(100);
+ }
+}
#endif /* CONFIG_CMD_PCI */
#ifdef CONFIG_SERIAL_TAG
else if (is_cpu_type(MXC_CPU_MX6DL) ||
is_cpu_type(MXC_CPU_MX6SOLO))
cputype = "imx6dl";
+ setenv("soctype", cputype);
if (8 << (ventana_info.nand_flash_size-1) >= 2048)
setenv("flash_layout", "large");
else
sprintf(fdt, "%s-%s.dtb", cputype, str);
setenv("fdt_file1", fdt);
}
- str[4] = 'x';
+ if (board_type != GW552x)
+ str[4] = 'x';
str[5] = 'x';
str[6] = 0;
if (!getenv("fdt_file2")) {
* The Gateworks System Controller implements a boot
* watchdog (always enabled) as a workaround for IMX6 boot related
* errata such as:
- * ERR005768 - no fix
- * ERR006282 - fixed in silicon r1.3
+ * ERR005768 - no fix scheduled
+ * ERR006282 - fixed in silicon r1.2
* ERR007117 - fixed in silicon r1.3
* ERR007220 - fixed in silicon r1.3
+ * ERR007926 - no fix scheduled
* see http://cache.freescale.com/files/32bit/doc/errata/IMX6DQCE.pdf
*
* Disable the boot watchdog and display/clear the timeout flag if set
.trasmin = 3500,
};
-/* GW54xx specific calibration */
-static struct mx6_mmdc_calibration gw54xxq_mmdc_calib = {
+/* MT41K256M16HA-125 */
+static struct mx6_ddr3_cfg mt41k256m16ha_125 = {
+ .mem_speed = 1600,
+ .density = 4,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 15,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1375,
+ .trcmin = 4875,
+ .trasmin = 3500,
+};
+
+/*
+ * calibration - these are the various CPU/DDR3 combinations we support
+ */
+
+static struct mx6_mmdc_calibration mx6dq_128x32_mmdc_calib = {
/* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x00190018,
- .p0_mpwldectrl1 = 0x0021001D,
- .p1_mpwldectrl0 = 0x00160027,
- .p1_mpwldectrl1 = 0x0012001E,
+ .p0_mpwldectrl0 = 0x00190017,
+ .p0_mpwldectrl1 = 0x00140026,
/* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x43370346,
- .p0_mpdgctrl1 = 0x032A0321,
- .p1_mpdgctrl0 = 0x433A034D,
- .p1_mpdgctrl1 = 0x032F0235,
+ .p0_mpdgctrl0 = 0x43380347,
+ .p0_mpdgctrl1 = 0x433C034D,
/* Read Calibration: DQS delay relative to DQ read access */
.p0_mprddlctl = 0x3C313539,
- .p1_mprddlctl = 0x37333140,
/* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x37393C38,
- .p1_mpwrdlctl = 0x42334538,
+ .p0_mpwrdlctl = 0x36393C39,
+};
+
+static struct mx6_mmdc_calibration mx6sdl_128x32_mmdc_calib = {
+ /* write leveling calibration determine */
+ .p0_mpwldectrl0 = 0x003C003C,
+ .p0_mpwldectrl1 = 0x001F002A,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x42410244,
+ .p0_mpdgctrl1 = 0x4234023A,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x484A4C4B,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x33342B32,
};
-/* GW53xx specific calibration */
-static struct mx6_mmdc_calibration gw53xxq_mmdc_calib = {
+static struct mx6_mmdc_calibration mx6dq_128x64_mmdc_calib = {
/* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x00160013,
- .p0_mpwldectrl1 = 0x00090024,
- .p1_mpwldectrl0 = 0x001F0018,
- .p1_mpwldectrl1 = 0x000C001C,
+ .p0_mpwldectrl0 = 0x00190017,
+ .p0_mpwldectrl1 = 0x00140026,
+ .p1_mpwldectrl0 = 0x0021001C,
+ .p1_mpwldectrl1 = 0x0011001D,
/* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x433A034C,
- .p0_mpdgctrl1 = 0x0336032F,
- .p1_mpdgctrl0 = 0x4343034A,
- .p1_mpdgctrl1 = 0x03370222,
+ .p0_mpdgctrl0 = 0x43380347,
+ .p0_mpdgctrl1 = 0x433C034D,
+ .p1_mpdgctrl0 = 0x032C0324,
+ .p1_mpdgctrl1 = 0x03310232,
/* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x3F343638,
- .p1_mprddlctl = 0x38373442,
+ .p0_mprddlctl = 0x3C313539,
+ .p1_mprddlctl = 0x37343141,
/* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x343A3E39,
- .p1_mpwrdlctl = 0x44344239,
+ .p0_mpwrdlctl = 0x36393C39,
+ .p1_mpwrdlctl = 0x42344438,
};
-static struct mx6_mmdc_calibration gw53xxdl_mmdc_calib = {
+
+static struct mx6_mmdc_calibration mx6sdl_128x64_mmdc_calib = {
/* write leveling calibration determine */
.p0_mpwldectrl0 = 0x003C003C,
- .p0_mpwldectrl1 = 0x00330038,
- .p1_mpwldectrl0 = 0x001F002A,
+ .p0_mpwldectrl1 = 0x001F002A,
+ .p1_mpwldectrl0 = 0x00330038,
.p1_mpwldectrl1 = 0x0022003F,
/* Read DQS Gating calibration */
.p0_mpdgctrl0 = 0x42410244,
- .p0_mpdgctrl1 = 0x022D022D,
- .p1_mpdgctrl0 = 0x4234023A,
+ .p0_mpdgctrl1 = 0x4234023A,
+ .p1_mpdgctrl0 = 0x022D022D,
.p1_mpdgctrl1 = 0x021C0228,
/* Read Calibration: DQS delay relative to DQ read access */
.p0_mprddlctl = 0x484A4C4B,
.p1_mpwrdlctl = 0x3933332B,
};
-/* GW52xx specific calibration */
-static struct mx6_mmdc_calibration gw52xxdl_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x0040003F,
- .p0_mpwldectrl1 = 0x00370037,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x42420244,
- .p0_mpdgctrl1 = 0x022F022F,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x49464B4A,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x32362C32,
-};
-
-/* GW51xx specific calibration */
-static struct mx6_mmdc_calibration gw51xxq_mmdc_calib = {
+static struct mx6_mmdc_calibration mx6dq_256x32_mmdc_calib = {
/* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x00150016,
- .p0_mpwldectrl1 = 0x001F0017,
+ .p0_mpwldectrl0 = 0x001E001A,
+ .p0_mpwldectrl1 = 0x0026001F,
/* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x433D034D,
- .p0_mpdgctrl1 = 0x033D032F,
+ .p0_mpdgctrl0 = 0x43370349,
+ .p0_mpdgctrl1 = 0x032D0327,
/* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x3F313639,
+ .p0_mprddlctl = 0x3D303639,
/* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x33393F36,
+ .p0_mpwrdlctl = 0x32363934,
};
-static struct mx6_mmdc_calibration gw51xxdl_mmdc_calib = {
+static struct mx6_mmdc_calibration mx6dq_256x64_mmdc_calib = {
/* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x003D003F,
- .p0_mpwldectrl1 = 0x002F0038,
+ .p0_mpwldectrl0 = 0X00220021,
+ .p0_mpwldectrl1 = 0X00200030,
+ .p1_mpwldectrl0 = 0X002D0027,
+ .p1_mpwldectrl1 = 0X00150026,
/* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x423A023A,
- .p0_mpdgctrl1 = 0x022A0228,
+ .p0_mpdgctrl0 = 0x43330342,
+ .p0_mpdgctrl1 = 0x0339034A,
+ .p1_mpdgctrl0 = 0x032F0325,
+ .p1_mpdgctrl1 = 0x032F022E,
/* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x48494C4C,
+ .p0_mprddlctl = 0X3A2E3437,
+ .p1_mprddlctl = 0X35312F3F,
/* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x34352D31,
+ .p0_mpwrdlctl = 0X33363B37,
+ .p1_mpwrdlctl = 0X40304239,
};
-static void spl_dram_init(int width, int size, int board_model)
+static void spl_dram_init(int width, int size_mb, int board_model)
{
- struct mx6_ddr3_cfg *mem = &mt41k128m16jt_125;
- struct mx6_mmdc_calibration *calib;
+ struct mx6_ddr3_cfg *mem = NULL;
+ struct mx6_mmdc_calibration *calib = NULL;
struct mx6_ddr_sysinfo sysinfo = {
/* width of data bus:0=16,1=32,2=64 */
.dsize = width/32,
/*
* MMDC Calibration requires the following data:
* mx6_mmdc_calibration - board-specific calibration (routing delays)
+ * these calibration values depend on board routing, SoC, and DDR
* mx6_ddr_sysinfo - board-specific memory architecture (width/cs/etc)
* mx6_ddr_cfg - chip specific timing/layout details
*/
- switch (board_model) {
- default:
- case GW51xx:
+ if (width == 32 && size_mb == 512) {
+ mem = &mt41k128m16jt_125;
if (is_cpu_type(MXC_CPU_MX6Q))
- calib = &gw51xxq_mmdc_calib;
+ calib = &mx6dq_128x32_mmdc_calib;
else
- calib = &gw51xxdl_mmdc_calib;
- break;
- case GW52xx:
- calib = &gw52xxdl_mmdc_calib;
- break;
- case GW53xx:
+ calib = &mx6sdl_128x32_mmdc_calib;
+ debug("2gB density\n");
+ } else if (width == 64 && size_mb == 1024) {
+ mem = &mt41k128m16jt_125;
if (is_cpu_type(MXC_CPU_MX6Q))
- calib = &gw53xxq_mmdc_calib;
+ calib = &mx6dq_128x64_mmdc_calib;
else
- calib = &gw53xxdl_mmdc_calib;
- break;
- case GW54xx:
- calib = &gw54xxq_mmdc_calib;
- break;
+ calib = &mx6sdl_128x64_mmdc_calib;
+ debug("2gB density\n");
+ } else if (width == 32 && size_mb == 1024) {
+ mem = &mt41k256m16ha_125;
+ if (is_cpu_type(MXC_CPU_MX6Q))
+ calib = &mx6dq_256x32_mmdc_calib;
+ debug("4gB density\n");
+ } else if (width == 64 && size_mb == 2048) {
+ mem = &mt41k256m16ha_125;
+ if (is_cpu_type(MXC_CPU_MX6Q))
+ calib = &mx6dq_256x64_mmdc_calib;
+ debug("4gB density\n");
+ }
+
+ if (!mem) {
+ puts("Error: Invalid Memory Configuration\n");
+ hang();
+ }
+ if (!calib) {
+ puts("Error: Invalid Board Calibration Configuration\n");
+ hang();
}
if (is_cpu_type(MXC_CPU_MX6Q))
GW52xx,
GW53xx,
GW54xx,
+ GW552x,
GW_UNKNOWN,
GW_BADCRC,
};
MX51_EFIKAMX BOARD
-M: -
+#M: -
S: Maintained
F: board/genesi/mx51_efikamx/
F: include/configs/mx51_efikamx.h
* PMIC configuration
*/
#ifdef CONFIG_MXC_SPI
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+ return (bus == 0 && cs == 1) ? 121 : -1;
+}
+
static void power_init(void)
{
unsigned int val;
F: configs/icecube_5200_defconfig
ICECUBE_5200_DDR BOARD
-M: -
+#M: -
S: Maintained
F: configs/icecube_5200_DDR_defconfig
F: configs/icecube_5200_DDR_LOWBOOT_defconfig
IMX31_PHYCORE BOARD
-M: -
+#M: -
S: Maintained
F: board/imx31_phycore/
F: include/configs/imx31_phycore.h
F: configs/imx31_phycore_defconfig
IMX31_PHYCORE_EET BOARD
-M: (resigned) Guennadi Liakhovetski <g.liakhovetski@gmx.de>
+#M: (resigned) Guennadi Liakhovetski <g.liakhovetski@gmx.de>
S: Orphan (since 2013-09)
F: configs/imx31_phycore_eet_defconfig
IP04 BOARD
-M: Brent Kandetzki <brentk@teleco.com>
+#M: Brent Kandetzki <brentk@teleco.com>
S: Orphan (since 2014-06)
F: board/ip04/
F: include/configs/ip04.h
F: configs/igep0032_defconfig
IGEP0020_NAND BOARD
-M: -
+#M: -
S: Maintained
F: configs/igep0020_nand_defconfig
F: configs/igep0030_nand_defconfig
+++ /dev/null
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
TK71 BOARD
-M: -
+#M: -
S: Maintained
F: board/karo/tk71/
F: include/configs/tk71.h
+++ /dev/null
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
IMX31_LITEKIT BOARD
-M: -
+#M: -
S: Maintained
F: board/logicpd/imx31_litekit/
F: include/configs/imx31_litekit.h
+++ /dev/null
-/*
- * (C) Copyright 2001-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
HMI1001 BOARD
-M: -
+#M: -
S: Maintained
F: board/manroland/hmi1001/
F: include/configs/hmi1001.h
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
MERGERBOX BOARD
-
M: Andre Schwarz <andre.schwarz@matrix-vision.de>
+
#M: Andre Schwarz <andre.schwarz@matrix-vision.de>
S: Orphan (since 2014-03)
F: board/matrix_vision/mergerbox/
F: include/configs/MERGERBOX.h
MVBC_P BOARD
-
M: Andre Schwarz <andre.schwarz@matrix-vision.de>
+
#M: Andre Schwarz <andre.schwarz@matrix-vision.de>
S: Orphan (since 2014-03)
F: board/matrix_vision/mvbc_p/
F: include/configs/MVBC_P.h
MVBLM7 BOARD
-
M: Andre Schwarz <andre.schwarz@matrix-vision.de>
+
#M: Andre Schwarz <andre.schwarz@matrix-vision.de>
S: Orphan (since 2014-03)
F: board/matrix_vision/mvblm7/
F: include/configs/MVBLM7.h
MVSMR BOARD
-
M: Andre Schwarz <andre.schwarz@matrix-vision.de>
+
#M: Andre Schwarz <andre.schwarz@matrix-vision.de>
S: Orphan (since 2014-03)
F: board/matrix_vision/mvsmr/
F: include/configs/MVSMR.h
MCC200 BOARD
-M: -
+#M: -
S: Maintained
F: board/mcc200/
F: include/configs/mcc200.h
VCT BOARD
-M: -
+#M: -
S: Maintained
F: board/micronas/vct/
F: include/configs/vct.h
MOTIONPRO BOARD
-M: -
+#M: -
S: Maintained
F: board/motionpro/
F: include/configs/motionpro.h
PATI BOARD
-M: -
+#M: -
S: Maintained
F: board/mpl/pati/
F: include/configs/PATI.h
MUNICES BOARD
-M: -
+#M: -
S: Maintained
F: board/munices/
F: include/configs/munices.h
MUSENKI BOARD
-M: Jim Thompson <jim@musenki.com>
+#M: Jim Thompson <jim@musenki.com>
S: Orphan (since 2014-04)
F: board/musenki/
F: include/configs/MUSENKI.h
MVBLUE BOARD
-M: -
+#M: -
S: Maintained
F: board/mvblue/
F: include/configs/MVBLUE.h
+++ /dev/null
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
PALMTREO680 BOARD
-M: Mike Dunn <mikedunn@newsguy.com>
+#M: Mike Dunn <mikedunn@newsguy.com>
S: Orphan (since 2014-06)
F: board/palmtreo680/
F: include/configs/palmtreo680.h
PB1X00 BOARD
-M: -
+#M: -
S: Maintained
F: board/pb1x00/
F: include/configs/pb1x00.h
PM828 BOARD
-M: -
+#M: -
S: Maintained
F: board/pm828/
F: include/configs/PM828.h
PPMC7XX BOARD
-M: -
+#M: -
S: Maintained
F: board/ppmc7xx/
F: include/configs/ppmc7xx.h
PPMC8260 BOARD
-M: Brad Kemp <Brad.Kemp@seranoa.com>
+#M: Brad Kemp <Brad.Kemp@seranoa.com>
S: Orphan (since 2014-04)
F: board/ppmc8260/
F: include/configs/ppmc8260.h
F: configs/qemu_mips_defconfig
QEMU_MIPSEL BOARD
-M: -
+#M: -
S: Maintained
F: configs/qemu_mipsel_defconfig
F: include/configs/qemu-mips64.h
MIGOR BOARD
-M: -
+#M: -
S: Maintained
F: board/renesas/MigoR/
F: include/configs/MigoR.h
RSK7269 BOARD
-M: -
+#M: -
S: Maintained
F: board/renesas/rsk7269/
F: include/configs/rsk7269.h
SH7752EVB BOARD
-M: -
+#M: -
S: Maintained
F: board/renesas/sh7752evb/
F: include/configs/sh7752evb.h
SH7753EVB BOARD
-M: -
+#M: -
S: Maintained
F: board/renesas/sh7753evb/
F: include/configs/sh7753evb.h
SH7757LCR BOARD
-M: -
+#M: -
S: Maintained
F: board/renesas/sh7757lcr/
F: include/configs/sh7757lcr.h
SH7785LCR BOARD
-M: -
+#M: -
S: Maintained
F: board/renesas/sh7785lcr/
F: include/configs/sh7785lcr.h
SACSNG BOARD
-M: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
+#M: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
S: Orphan (since 2014-06)
F: board/sacsng/
F: include/configs/sacsng.h
CONFIG_SANDBOX is defined when building a native board.
The chosen vendor and board names are also 'sandbox', so there is a single
-board in board/sandbox/sandbox.
+board in board/sandbox.
CONFIG_SANDBOX_BIG_ENDIAN should be defined when running on big-endian
machines.
To run sandbox U-Boot use something like:
- make sandbox_config all
+ make sandbox_defconfig all
./u-boot
Note:
build sandbox without SDL (i.e. no display/keyboard support) by removing
the CONFIG_SANDBOX_SDL line in include/configs/sandbox.h or using:
- make sandbox_config all NO_SDL=1
+ make sandbox_defconfig all NO_SDL=1
./u-boot
KAREF BOARD
-M: Travis Sawyer <travis.sawyer@sandburst.com>
+#M: Travis Sawyer <travis.sawyer@sandburst.com>
S: Orphan (since 2014-03)
F: board/sandburst/karef/
F: include/configs/KAREF.h
METROBOX BOARD
-M: Travis Sawyer <travis.sawyer@sandburst.com>
+#M: Travis Sawyer <travis.sawyer@sandburst.com>
S: Orphan (since 2014-03)
F: board/sandburst/metrobox/
F: include/configs/METROBOX.h
F: configs/Sandpoint8240_defconfig
SANDPOINT8245 BOARD
-M: Jim Thompson <jim@musenki.com>
+#M: Jim Thompson <jim@musenki.com>
S: Orphan (since 2014-04)
F: include/configs/Sandpoint8245.h
F: configs/Sandpoint8245_defconfig
SBC405 BOARD
-M: -
+#M: -
S: Maintained
F: board/sbc405/
F: include/configs/sbc405.h
SOCRATES BOARD
-M: -
+#M: -
S: Maintained
F: board/socrates/
F: include/configs/socrates.h
F: configs/spear300_defconfig
SPEAR300_NAND BOARD
-M: -
+#M: -
S: Maintained
F: configs/spear300_nand_defconfig
F: configs/spear300_usbtty_defconfig
F: configs/spear310_defconfig
SPEAR310_NAND BOARD
-M: -
+#M: -
S: Maintained
F: configs/spear310_nand_defconfig
F: configs/spear310_pnor_defconfig
F: configs/spear320_defconfig
SPEAR320_NAND BOARD
-M: -
+#M: -
S: Maintained
F: configs/spear320_nand_defconfig
F: configs/spear320_pnor_defconfig
F: configs/spear600_defconfig
SPEAR600_NAND BOARD
-M: -
+#M: -
S: Maintained
F: configs/spear600_nand_defconfig
F: configs/spear600_usbtty_defconfig
U8500 BOARD
-M: -
+#M: -
S: Maintained
F: board/st-ericsson/u8500/
F: include/configs/u8500_href.h
STXGP3 BOARD
-M: Dan Malek <dan@embeddedalley.com>
+#M: Dan Malek <dan@embeddedalley.com>
S: Orphan (since 2014-06)
F: board/stx/stxgp3/
F: include/configs/stxgp3.h
STXSSA BOARD
-M: Dan Malek <dan@embeddedalley.com>
+#M: Dan Malek <dan@embeddedalley.com>
S: Orphan (since 2014-06)
F: board/stx/stxssa/
F: include/configs/stxssa.h
TCM-BF518 BOARD
-M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
+#M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
S: Orphan (since 2014-03)
F: board/tcm-bf518/
F: include/configs/tcm-bf518.h
TCM-BF537 BOARD
-M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
+#M: Bluetechnix Tinyboards <bluetechnix@blackfin.uclinux.org>
S: Orphan (since 2014-03)
F: board/tcm-bf537/
F: include/configs/tcm-bf537.h
F: configs/omap3_evm_defconfig
OMAP3_EVM_QUICK_MMC BOARD
-M: -
+#M: -
S: Maintained
F: include/configs/omap3_evm_quick_mmc.h
F: configs/omap3_evm_quick_mmc_defconfig
while (1)
;
}
+
+ /* Apply the workaround for PG 1.0 and 1.1 Silicons */
+ if (cpu_revision() <= 1)
+ ddr3_err_reset_workaround();
}
TI816X BOARD
-M: -
+#M: -
S: Maintained
F: board/ti/ti816x/
F: include/configs/ti816x_evm.h
TNETV107XEVM BOARD
-M: Chan-Taek Park <c-park@ti.com>
+#M: Chan-Taek Park <c-park@ti.com>
S: Orphan (since 2014-06)
F: board/ti/tnetv107xevm/
F: include/configs/tnetv107x_evm.h
TOTAL5200 BOARD
-M: -
+#M: -
S: Maintained
F: board/total5200/
F: include/configs/Total5200.h
TQM5200 BOARD
-M: -
+#M: -
S: Maintained
F: board/tqc/tqm5200/
F: include/configs/aev.h
TQM8272 BOARD
-M: -
+#M: -
S: Maintained
F: board/tqc/tqm8272/
F: include/configs/TQM8272.h
TQM834X BOARD
-M: -
+#M: -
S: Maintained
F: board/tqc/tqm834x/
F: include/configs/TQM834x.h
F: configs/wtk_defconfig
NSCU BOARD
-M: -
+#M: -
S: Maintained
F: include/configs/NSCU.h
F: configs/NSCU_defconfig
}
#ifdef CONFIG_MXC_SPI
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+ return (bus == 0 && cs == 1) ? 121 : -1;
+}
+
void spi_io_init(void)
{
static const iomux_v3_cfg_t spi_pads[] = {
V38B BOARD
-M: -
+#M: -
S: Maintained
F: board/v38b/
F: include/configs/v38b.h
F: configs/woodburn_defconfig
WOODBURN_SD BOARD
-M: -
+#M: -
S: Maintained
F: include/configs/woodburn_sd.h
F: configs/woodburn_sd_defconfig
XAENIAX BOARD
-M: -
+#M: -
S: Maintained
F: board/xaeniax/
F: include/configs/xaeniax.h
XPEDITE517X BOARD
-M: -
+#M: -
S: Maintained
F: board/xes/xpedite517x/
F: include/configs/xpedite517x.h
XPEDITE520X BOARD
-M: -
+#M: -
S: Maintained
F: board/xes/xpedite520x/
F: include/configs/xpedite520x.h
XPEDITE537X BOARD
-M: -
+#M: -
S: Maintained
F: board/xes/xpedite537x/
F: include/configs/xpedite537x.h
XPEDITE550X BOARD
-M: -
+#M: -
S: Maintained
F: board/xes/xpedite550x/
F: include/configs/xpedite550x.h
--- /dev/null
+menu "Command line interface"
+ depends on !SPL_BUILD
+
+config CMD_BOOTM
+ bool "Enable bootm command"
+ default y
+ help
+ Boot an application image from the memory.
+
+config CMD_CRC32
+ bool "Enable crc32 command"
+ default y
+ help
+ Compute CRC32.
+
+config CMD_EXPORTENV
+ bool "Enable env export command"
+ default y
+ help
+ Export environments.
+
+config CMD_IMPORTENV
+ bool "Enable env import command"
+ default y
+ help
+ Import environments.
+
+config CMD_GO
+ bool "Enable go command"
+ default y
+ help
+ Start an application at a given address.
+
+endmenu
#environment
obj-y += env_common.o
#others
-ifdef CONFIG_DDR_SPD
-SPD := y
-endif
-ifdef CONFIG_SPD_EEPROM
-SPD := y
-endif
-obj-$(SPD) += ddr_spd.o
+obj-$(CONFIG_DDR_SPD) += ddr_spd.o
+obj-$(CONFIG_SPD_EEPROM) += ddr_spd.o
obj-$(CONFIG_HWCONFIG) += hwconfig.o
obj-$(CONFIG_BOUNCE_BUFFER) += bouncebuf.o
obj-y += console.o
obj-y += memsize.o
obj-y += stdio.o
+# This option is not just y/n - it can have a numeric value
+ifdef CONFIG_FASTBOOT_FLASH_MMC_DEV
+obj-y += aboot.o
+obj-y += fb_mmc.o
+endif
+
CFLAGS_env_embedded.o := -Wa,--no-warn -DENV_CRC=$(shell tools/envcrc 2>/dev/null)
#ifdef CONFIG_MPC5xxx
#include <mpc5xxx.h>
#endif
-#if (defined(CONFIG_MPC86xx) || defined(CONFIG_E500))
+#if defined(CONFIG_MP) && (defined(CONFIG_MPC86xx) || defined(CONFIG_E500))
#include <asm/mp.h>
#endif
static int setup_fdt(void)
{
-#ifdef CONFIG_OF_EMBED
+#ifdef CONFIG_OF_CONTROL
+# ifdef CONFIG_OF_EMBED
/* Get a pointer to the FDT */
gd->fdt_blob = __dtb_dt_begin;
-#elif defined CONFIG_OF_SEPARATE
+# elif defined CONFIG_OF_SEPARATE
/* FDT is at end of image */
gd->fdt_blob = (ulong *)&_end;
-#elif defined(CONFIG_OF_HOSTFILE)
+# elif defined(CONFIG_OF_HOSTFILE)
if (read_fdt_from_file()) {
puts("Failed to read control FDT\n");
return -1;
}
-#endif
+# endif
/* Allow the early environment to override the fdt address */
gd->fdt_blob = (void *)getenv_ulong("fdtcontroladdr", 16,
(uintptr_t)gd->fdt_blob);
+#endif
return 0;
}
gd->ram_top = board_get_usable_ram_top(gd->mon_len);
gd->relocaddr = gd->ram_top;
debug("Ram top: %08lX\n", (ulong)gd->ram_top);
-#if (defined(CONFIG_MPC86xx) || defined(CONFIG_E500))
+#if defined(CONFIG_MP) && (defined(CONFIG_MPC86xx) || defined(CONFIG_E500))
/*
* We need to make sure the location we intend to put secondary core
* boot code is reserved and not used by any part of u-boot
}
U_BOOT_CMD(
- fastboot, 1, 1, do_fastboot,
- "fastboot - enter USB Fastboot protocol",
- ""
+ fastboot, 1, 0, do_fastboot,
+ "use USB Fastboot protocol",
+ "\n"
+ " - run as a fastboot usb device"
);
read = strncmp(cmd, "read", 4) == 0; /* 1 = read, 0 = write */
printf("\nNAND %s: ", read ? "read" : "write");
- nand = &nand_info[dev];
-
s = strchr(cmd, '.');
if (s && !strcmp(s, ".raw")) {
if (arg_off(argv[3], &dev, &off, &size, &maxsize))
return 1;
+ nand = &nand_info[dev];
+
if (argc > 4 && !str2long(argv[4], &pagecount)) {
printf("'%s' is not a number\n", argv[4]);
return 1;
rwsize = size;
}
+ nand = &nand_info[dev];
+
if (!s || !strcmp(s, ".jffs2") ||
!strcmp(s, ".e") || !strcmp(s, ".i")) {
if (read)
#include <asm/io.h>
-#ifndef CONFIG_SF_DEFAULT_SPEED
-# define CONFIG_SF_DEFAULT_SPEED 1000000
-#endif
-#ifndef CONFIG_SF_DEFAULT_MODE
-# define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
-#endif
-#ifndef CONFIG_SF_DEFAULT_CS
-# define CONFIG_SF_DEFAULT_CS 0
-#endif
-#ifndef CONFIG_SF_DEFAULT_BUS
-# define CONFIG_SF_DEFAULT_BUS 0
-#endif
-
static struct spi_flash *flash;
#include <common.h>
#include <command.h>
+#include <errno.h>
#include <spi.h>
/*-----------------------------------------------------------------------
static uchar dout[MAX_SPI_BYTES];
static uchar din[MAX_SPI_BYTES];
+static int do_spi_xfer(int bus, int cs)
+{
+ struct spi_slave *slave;
+ int rcode = 0;
+
+ slave = spi_setup_slave(bus, cs, 1000000, mode);
+ if (!slave) {
+ printf("Invalid device %d:%d\n", bus, cs);
+ return -EINVAL;
+ }
+
+ spi_claim_bus(slave);
+ if (spi_xfer(slave, bitlen, dout, din,
+ SPI_XFER_BEGIN | SPI_XFER_END) != 0) {
+ printf("Error during SPI transaction\n");
+ rcode = -EIO;
+ } else {
+ int j;
+
+ for (j = 0; j < ((bitlen + 7) / 8); j++)
+ printf("%02X", din[j]);
+ printf("\n");
+ }
+ spi_release_bus(slave);
+ spi_free_slave(slave);
+
+ return rcode;
+}
+
/*
* SPI read/write
*
int do_spi (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
- struct spi_slave *slave;
char *cp = 0;
uchar tmp;
int j;
- int rcode = 0;
/*
* We use the last specified parameters, unless new ones are
return 1;
}
- slave = spi_setup_slave(bus, cs, 1000000, mode);
- if (!slave) {
- printf("Invalid device %d:%d\n", bus, cs);
+ if (do_spi_xfer(bus, cs))
return 1;
- }
-
- spi_claim_bus(slave);
- if(spi_xfer(slave, bitlen, dout, din,
- SPI_XFER_BEGIN | SPI_XFER_END) != 0) {
- printf("Error during SPI transaction\n");
- rcode = 1;
- } else {
- for(j = 0; j < ((bitlen + 7) / 8); j++) {
- printf("%02X", din[j]);
- }
- printf("\n");
- }
- spi_release_bus(slave);
- spi_free_slave(slave);
- return rcode;
+ return 0;
}
/***************************************************/
static int ctrlc_was_pressed = 0;
int ctrlc(void)
{
+#ifndef CONFIG_SANDBOX
if (!ctrlc_disabled && gd->have_console) {
if (tstc()) {
switch (getc()) {
}
}
}
+#endif
+
return 0;
}
/* Reads user's confirmation.
--- /dev/null
+/*
+ * Copyright 2014 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <fb_mmc.h>
+#include <part.h>
+#include <aboot.h>
+#include <sparse_format.h>
+
+/* The 64 defined bytes plus the '\0' */
+#define RESPONSE_LEN (64 + 1)
+
+static char *response_str;
+
+void fastboot_fail(const char *s)
+{
+ strncpy(response_str, "FAIL", 4);
+ strncat(response_str, s, RESPONSE_LEN - 4 - 1);
+}
+
+void fastboot_okay(const char *s)
+{
+ strncpy(response_str, "OKAY", 4);
+ strncat(response_str, s, RESPONSE_LEN - 4 - 1);
+}
+
+static void write_raw_image(block_dev_desc_t *dev_desc, disk_partition_t *info,
+ const char *part_name, void *buffer,
+ unsigned int download_bytes)
+{
+ lbaint_t blkcnt;
+ lbaint_t blks;
+
+ /* determine number of blocks to write */
+ blkcnt = ((download_bytes + (info->blksz - 1)) & ~(info->blksz - 1));
+ blkcnt = blkcnt / info->blksz;
+
+ if (blkcnt > info->size) {
+ error("too large for partition: '%s'\n", part_name);
+ fastboot_fail("too large for partition");
+ return;
+ }
+
+ puts("Flashing Raw Image\n");
+
+ blks = dev_desc->block_write(dev_desc->dev, info->start, blkcnt,
+ buffer);
+ if (blks != blkcnt) {
+ error("failed writing to device %d\n", dev_desc->dev);
+ fastboot_fail("failed writing to device");
+ return;
+ }
+
+ printf("........ wrote " LBAFU " bytes to '%s'\n", blkcnt * info->blksz,
+ part_name);
+ fastboot_okay("");
+}
+
+void fb_mmc_flash_write(const char *cmd, void *download_buffer,
+ unsigned int download_bytes, char *response)
+{
+ int ret;
+ block_dev_desc_t *dev_desc;
+ disk_partition_t info;
+
+ /* initialize the response buffer */
+ response_str = response;
+
+ dev_desc = get_dev("mmc", CONFIG_FASTBOOT_FLASH_MMC_DEV);
+ if (!dev_desc || dev_desc->type == DEV_TYPE_UNKNOWN) {
+ error("invalid mmc device\n");
+ fastboot_fail("invalid mmc device");
+ return;
+ }
+
+ ret = get_partition_info_efi_by_name(dev_desc, cmd, &info);
+ if (ret) {
+ error("cannot find partition: '%s'\n", cmd);
+ fastboot_fail("cannot find partition");
+ return;
+ }
+
+ if (is_sparse_image(download_buffer))
+ write_sparse_image(dev_desc, &info, cmd, download_buffer,
+ download_bytes);
+ else
+ write_raw_image(dev_desc, &info, cmd, download_buffer,
+ download_bytes);
+}
fdt_delprop(blob, off, alias);
}
-/* Helper to read a big number; size is in cells (not bytes) */
-static inline u64 of_read_number(const fdt32_t *cell, int size)
-{
- u64 r = 0;
- while (size--)
- r = (r << 32) | fdt32_to_cpu(*(cell++));
- return r;
-}
-
#define PRu64 "%llx"
/* Max address size we deal with */
};
/* Default translator (generic bus) */
-static void of_bus_default_count_cells(void *blob, int parentoffset,
+void of_bus_default_count_cells(void *blob, int parentoffset,
int *addrc, int *sizec)
{
const fdt32_t *prop;
sinclude $(srctree)/board/$(BOARDDIR)/config.mk # include board specific rules
endif
+ifdef FTRACE
+PLATFORM_CPPFLAGS += -finstrument-functions -DFTRACE
+endif
+
#########################################################################
RELFLAGS := $(PLATFORM_RELFLAGS)
--- /dev/null
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1042,T1042RDB"
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_T104XRDB=y
CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,EMMC_BOOT,ENABLE_VBOOT"
+S:CONFIG_ARM=y
+S:CONFIG_TARGET_AM335X_EVM=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="am335x-boneblack"
+S:CONFIG_ARM=y
+S:CONFIG_ARCH_EXYNOS=y
+S:CONFIG_TARGET_ARNDALE=y
+CONFIG_DEFAULT_DEVICE_TREE="exynos5250-arndale"
CONFIG_BLACKFIN=y
CONFIG_TARGET_BCT_BRETTL2=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA30=y
+S:CONFIG_TARGET_BEAVER=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra30-beaver"
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF506F_EZKIT=y
+# CONFIG_CMD_BOOTM is not set
+# CONFIG_CMD_EXPORTENV is not set
+# CONFIG_CMD_IMPORTENV is not set
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF518F_EZBRD=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF526_EZBRD=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF527_AD7160_EVAL=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_SYS_EXTRA_OPTIONS="BF527_EZKIT_REV_2_1"
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF527_EZKIT=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF527_EZKIT=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF527_SDP=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF533_EZKIT=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF533_STAMP=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF537_STAMP=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF538F_EZKIT=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF548_EZKIT=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF561_ACVILON=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_BF561_EZKIT=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_BR4=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA30=y
+S:CONFIG_TARGET_CARDHU=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra30-cardhu"
CONFIG_BLACKFIN=y
CONFIG_TARGET_CM_BF527=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_CM_BF533=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_CM_BF537E=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_CM_BF537U=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_CM_BF548=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_CM_BF561=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
--- /dev/null
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/compulab/cm_fx6/imximage.cfg,MX6QDL,SPL"
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_CM_FX6=y
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA20=y
+S:CONFIG_TARGET_COLIBRI_T20_IRIS=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra20-colibri_t20_iris"
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA30=y
+S:CONFIG_TARGET_COLIBRI_T30=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra30-colibri"
CONFIG_PPC=y
CONFIG_MPC85xx=y
CONFIG_TARGET_CONTROLCENTERD=y
+# CONFIG_CMD_BOOTM is not set
CONFIG_PPC=y
CONFIG_MPC85xx=y
CONFIG_TARGET_CONTROLCENTERD=y
+# CONFIG_CMD_BOOTM is not set
CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0x01110000"
CONFIG_X86=y
CONFIG_TARGET_COREBOOT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="link"
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA114=y
+S:CONFIG_TARGET_DALMORE=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra114-dalmore"
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA20=y
+S:CONFIG_TARGET_HARMONY=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra20-harmony"
CONFIG_BLACKFIN=y
CONFIG_TARGET_IP04=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA124=y
+S:CONFIG_TARGET_JETSON_TK1=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra124-jetson-tk1"
CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1"
+S:CONFIG_ARM=y
+S:CONFIG_TARGET_KWB=y
+# CONFIG_CMD_CRC32 is not set
--- /dev/null
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
+CONFIG_ARM=y
+CONFIG_TARGET_LS1021AQDS=y
-CONFIG_SYS_EXTRA_OPTIONS="ARM64,EMU,SYS_FSL_DDR4"
+CONFIG_SYS_EXTRA_OPTIONS="EMU,SYS_FSL_DDR4"
CONFIG_ARM=y
CONFIG_TARGET_LS2085A_EMU=y
-CONFIG_SYS_EXTRA_OPTIONS="ARM64,EMU"
+CONFIG_SYS_EXTRA_OPTIONS="EMU"
CONFIG_ARM=y
CONFIG_TARGET_LS2085A_EMU=y
-CONFIG_SYS_EXTRA_OPTIONS="ARM64,SIMU"
+CONFIG_SYS_EXTRA_OPTIONS="SIMU"
CONFIG_ARM=y
CONFIG_TARGET_LS2085A_SIMU=y
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA20=y
+S:CONFIG_TARGET_MEDCOM_WIDE=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra20-medcom-wide"
CONFIG_SPL=y
+S:CONFIG_MICROBLAZE=y
+S:CONFIG_TARGET_MICROBLAZE_GENERIC=y
+CONFIG_OF_CONTROL=y
+CONFIG_OF_EMBED=y
+CONFIG_DEFAULT_DEVICE_TREE="microblaze-generic"
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sabresd/mx6dlsabresd.cfg,MX6DL"
CONFIG_ARM=y
CONFIG_TARGET_MX6SABRESD=y
CONFIG_ARM=y
CONFIG_ARCH_EXYNOS=y
CONFIG_TARGET_ODROID=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="exynos4412-odroid"
+S:CONFIG_ARM=y
+S:CONFIG_ARCH_EXYNOS=y
+S:CONFIG_TARGET_ORIGEN=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="exynos4210-origen"
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA20=y
+S:CONFIG_TARGET_PAZ00=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra20-paz00"
+S:CONFIG_ARM=y
+S:CONFIG_ARCH_EXYNOS=y
+S:CONFIG_TARGET_PEACH_PIT=y
+CONFIG_DEFAULT_DEVICE_TREE="exynos5420-peach-pit"
--- /dev/null
+CONFIG_SPL=y
++S:CONFIG_ARM=y
++S:CONFIG_ARCH_UNIPHIER=y
++S:CONFIG_MACH_PH1_LD4=y
+CONFIG_NAND_DENALI=y
+CONFIG_SYS_NAND_DENALI_64BIT=y
+CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES=8
+S:CONFIG_SPL_NAND_DENALI=y
--- /dev/null
+CONFIG_SPL=y
++S:CONFIG_ARM=y
++S:CONFIG_ARCH_UNIPHIER=y
++S:CONFIG_MACH_PH1_PRO4=y
+CONFIG_NAND_DENALI=y
+CONFIG_SYS_NAND_DENALI_64BIT=y
+CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES=8
+S:CONFIG_SPL_NAND_DENALI=y
--- /dev/null
+CONFIG_SPL=y
++S:CONFIG_ARM=y
++S:CONFIG_ARCH_UNIPHIER=y
++S:CONFIG_MACH_PH1_SLD8=y
+CONFIG_NAND_DENALI=y
+CONFIG_SYS_NAND_DENALI_64BIT=y
+CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES=8
+S:CONFIG_SPL_NAND_DENALI=y
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA20=y
+S:CONFIG_TARGET_PLUTUX=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra20-plutux"
CONFIG_BLACKFIN=y
CONFIG_TARGET_PR1=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_ARM=y
CONFIG_ARCH_EXYNOS=y
CONFIG_TARGET_S5PC210_UNIVERSAL=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="exynos4210-universal_c210"
+CONFIG_OF_CONTROL=y
+CONFIG_OF_HOSTFILE=y
+CONFIG_DEFAULT_DEVICE_TREE="sandbox"
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA20=y
+S:CONFIG_TARGET_SEABOARD=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra20-seaboard"
+S:CONFIG_ARM=y
+S:CONFIG_ARCH_EXYNOS=y
+S:CONFIG_TARGET_SMDK5250=y
+CONFIG_DEFAULT_DEVICE_TREE="exynos5250-smdk5250"
+S:CONFIG_ARM=y
+S:CONFIG_ARCH_EXYNOS=y
+S:CONFIG_TARGET_SMDK5420=y
+CONFIG_DEFAULT_DEVICE_TREE="exynos5420-smdk5420"
+S:CONFIG_ARM=y
+S:CONFIG_ARCH_EXYNOS=y
+S:CONFIG_TARGET_SNOW=y
+CONFIG_DEFAULT_DEVICE_TREE="exynos5250-snow"
CONFIG_BLACKFIN=y
CONFIG_TARGET_TCM_BF518=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
CONFIG_BLACKFIN=y
CONFIG_TARGET_TCM_BF537=y
+CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED=y
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA30=y
+S:CONFIG_TARGET_TEC_NG=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra30-tec-ng"
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA20=y
+S:CONFIG_TARGET_TEC=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra20-tec"
CONFIG_ARM=y
CONFIG_ARCH_EXYNOS=y
CONFIG_TARGET_TRATS2=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="exynos4412-trats2"
CONFIG_ARM=y
CONFIG_ARCH_EXYNOS=y
CONFIG_TARGET_TRATS=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="exynos4210-trats"
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA20=y
+S:CONFIG_TARGET_TRIMSLICE=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra20-trimslice"
CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,EMMC_BOOT"
+S:CONFIG_ARM=y
+S:CONFIG_TARGET_TSERIES=y
+# CONFIG_CMD_CRC32 is not set
CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,NAND"
+S:CONFIG_ARM=y
+S:CONFIG_TARGET_TSERIES=y
+# CONFIG_CMD_CRC32 is not set
CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,SPI_BOOT,EMMC_BOOT"
+S:CONFIG_ARM=y
+S:CONFIG_TARGET_TSERIES=y
+# CONFIG_CMD_CRC32 is not set
CONFIG_SYS_EXTRA_OPTIONS="VCT_PLATINUM,VCT_ONENAND,VCT_SMALL_IMAGE"
CONFIG_MIPS=y
CONFIG_TARGET_VCT=y
+# CONFIG_CMD_CRC32 is not set
CONFIG_SYS_EXTRA_OPTIONS="VCT_PLATINUM,VCT_SMALL_IMAGE"
CONFIG_MIPS=y
CONFIG_TARGET_VCT=y
+# CONFIG_CMD_CRC32 is not set
CONFIG_SYS_EXTRA_OPTIONS="VCT_PLATINUMAVC,VCT_ONENAND,VCT_SMALL_IMAGE"
CONFIG_MIPS=y
CONFIG_TARGET_VCT=y
+# CONFIG_CMD_CRC32 is not set
CONFIG_SYS_EXTRA_OPTIONS="VCT_PLATINUMAVC,VCT_SMALL_IMAGE"
CONFIG_MIPS=y
CONFIG_TARGET_VCT=y
+# CONFIG_CMD_CRC32 is not set
CONFIG_SYS_EXTRA_OPTIONS="VCT_PREMIUM,VCT_ONENAND,VCT_SMALL_IMAGE"
CONFIG_MIPS=y
CONFIG_TARGET_VCT=y
+# CONFIG_CMD_CRC32 is not set
CONFIG_SYS_EXTRA_OPTIONS="VCT_PREMIUM,VCT_SMALL_IMAGE"
CONFIG_MIPS=y
CONFIG_TARGET_VCT=y
+# CONFIG_CMD_CRC32 is not set
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA124=y
+S:CONFIG_TARGET_VENICE2=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra124-venice2"
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA20=y
+S:CONFIG_TARGET_VENTANA=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra20-ventana"
-CONFIG_SYS_EXTRA_OPTIONS="ARM64"
CONFIG_ARM=y
CONFIG_TARGET_VEXPRESS_AEMV8A=y
+CONFIG_DEFAULT_DEVICE_TREE="vexpress64"
-CONFIG_SYS_EXTRA_OPTIONS="ARM64,SEMIHOSTING,BASE_FVP"
+CONFIG_SYS_EXTRA_OPTIONS="SEMIHOSTING,BASE_FVP"
CONFIG_ARM=y
-CONFIG_TARGET_VEXPRESS_AEMV8A_SEMI=y
+CONFIG_TARGET_VEXPRESS_AEMV8A=y
+CONFIG_DEFAULT_DEVICE_TREE="vexpress64"
+S:CONFIG_TEGRA=y
+S:CONFIG_TEGRA20=y
+S:CONFIG_TARGET_WHISTLER=y
+CONFIG_DEFAULT_DEVICE_TREE="tegra20-whistler"
+S:CONFIG_ARM=y
+S:CONFIG_ZYNQ=y
+S:CONFIG_TARGET_ZYNQ_MICROZED=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="zynq-microzed"
+S:CONFIG_ARM=y
+S:CONFIG_ZYNQ=y
+S:CONFIG_TARGET_ZYNQ_ZC70X=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="zynq-zc702"
+S:CONFIG_ARM=y
+S:CONFIG_ZYNQ=y
+S:CONFIG_TARGET_ZYNQ_ZC770=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="zynq-zc770-xm010"
+S:CONFIG_ARM=y
+S:CONFIG_ZYNQ=y
+S:CONFIG_TARGET_ZYNQ_ZC770=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="zynq-zc770-xm012"
+S:CONFIG_ARM=y
+S:CONFIG_ZYNQ=y
+S:CONFIG_TARGET_ZYNQ_ZC770=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="zynq-zc770-xm013"
+S:CONFIG_ARM=y
+S:CONFIG_ZYNQ=y
+S:CONFIG_TARGET_ZYNQ_ZED=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="zynq-zed"
* Overflowless variant of (block_count * mul_by / div_by)
* when div_by > mul_by
*/
-static lba512_t lba512_muldiv (lba512_t block_count, lba512_t mul_by, lba512_t div_by)
+static lba512_t lba512_muldiv(lba512_t block_count, lba512_t mul_by, lba512_t div_by)
{
lba512_t bc_quot, bc_rem;
lba512 = (lba * (dev_desc->blksz/512));
/* round to 1 digit */
- mb = lba512_muldiv(lba512, 10, 2048); /* 2048 = (1024 * 1024) / 512 MB */
+ /* 2048 = (1024 * 1024) / 512 MB */
+ mb = lba512_muldiv(lba512, 10, 2048);
mb_quot = mb / 10;
mb_rem = mb - (10 * mb_quot);
#ifdef HAVE_BLOCK_DEVICE
-void init_part (block_dev_desc_t * dev_desc)
+void init_part(block_dev_desc_t *dev_desc)
{
#ifdef CONFIG_ISO_PARTITION
if (test_part_iso(dev_desc) == 0) {
defined(CONFIG_AMIGA_PARTITION) || \
defined(CONFIG_EFI_PARTITION)
-static void print_part_header (const char *type, block_dev_desc_t * dev_desc)
+static void print_part_header(const char *type, block_dev_desc_t *dev_desc)
{
puts ("\nPartition Map for ");
switch (dev_desc->if_type) {
The protocol that is used over USB is described in
README.android-fastboot-protocol in same directory.
-The current implementation does not yet support the flash and erase
-commands.
+The current implementation does not yet support the erase command or the
+"oem format" command, and there is minimal support for the flash command;
+it only supports eMMC devices.
Client installation
===================
FreeBSD 11 (Current):
--------------------
Since llvm 3.4 is currently in the base system, the integrated as is
-incapable of building U-Boot. Therefore gas from devel/arm-eabi-binutils
+incapable of building U-Boot. Therefore gas from devel/arm-gnueabi-binutils
is used instead. It needs a symlinks to be picked up correctly though:
-ln -s /usr/local/bin/arm-eabi-as /usr/bin/arm-freebsd-eabi-as
+ln -s /usr/local/bin/arm-gnueabi-freebsd-as /usr/bin/arm-freebsd-eabi-as
# The following commands compile U-Boot using the clang xdev toolchain.
# NOTE: CROSS_COMPILE and target differ on purpose!
-export CROSS_COMPILE=arm-eabi-
+export CROSS_COMPILE=arm-gnueabi-freebsd-
gmake CC="clang -target arm-freebsd-eabi --sysroot /usr/arm-freebsd -no-integrated-as -mllvm -arm-use-movt=0" rpi_b_defconfig
gmake CC="clang -target arm-freebsd-eabi --sysroot /usr/arm-freebsd -no-integrated-as -mllvm -arm-use-movt=0" -j8
Given that u-boot will default to gcc, above commands can be
simplified with a simple wrapper script, listed below.
-/usr/local/bin/arm-eabi-gcc
+/usr/local/bin/arm-gnueabi-freebsd-gcc
---
#!/bin/sh
DATA 4 0x73FA88a0 0x200
The processor support up to 60 register programming commands for IMXIMAGE_VERSION 1
-and 121 register programming commands for IMXIMAGE_VERSION 2.
+and 220 register programming commands for IMXIMAGE_VERSION 2.
An error is generated if more commands are found in the configuration file.
3. All commands are optional to program.
alias tegra uboot, sjg, Tom Warren <twarren@nvidia.com>, Stephen Warren <swarren@nvidia.com>
alias tegra2 tegra
alias ti uboot, trini
+alias uniphier uboot, masahiro
alias zynq uboot, monstr
alias avr32 uboot, abiessmann
--- /dev/null
+menu "Device Drivers"
+
+source "drivers/core/Kconfig"
+
+source "drivers/pci/Kconfig"
+
+source "drivers/pcmcia/Kconfig"
+
+source "drivers/mtd/Kconfig"
+
+source "drivers/block/Kconfig"
+
+source "drivers/misc/Kconfig"
+
+source "drivers/net/Kconfig"
+
+source "drivers/input/Kconfig"
+
+source "drivers/serial/Kconfig"
+
+source "drivers/tpm/Kconfig"
+
+source "drivers/i2c/Kconfig"
+
+source "drivers/spi/Kconfig"
+
+source "drivers/gpio/Kconfig"
+
+source "drivers/power/Kconfig"
+
+source "drivers/hwmon/Kconfig"
+
+source "drivers/watchdog/Kconfig"
+
+source "drivers/video/Kconfig"
+
+source "drivers/sound/Kconfig"
+
+source "drivers/usb/Kconfig"
+
+source "drivers/dfu/Kconfig"
+
+source "drivers/mmc/Kconfig"
+
+source "drivers/rtc/Kconfig"
+
+source "drivers/dma/Kconfig"
+
+source "drivers/crypto/Kconfig"
+
+endmenu
+obj-$(CONFIG_DM) += core/
+obj-$(CONFIG_DM_DEMO) += demo/
obj-$(CONFIG_BIOSEMU) += bios_emulator/
obj-y += block/
obj-$(CONFIG_BOOTCOUNT_LIMIT) += bootcount/
obj-$(CONFIG_QE) += qe/
obj-y += memory/
obj-y += pwm/
+obj-y += input/
return blkcnt;
}
+int sata_port_status(int dev, int port)
+{
+ struct sata_port_regs *port_mmio;
+ struct ahci_probe_ent *probe_ent = NULL;
+
+ if (dev < 0 || dev > (CONFIG_SYS_SATA_MAX_DEVICE - 1))
+ return -EINVAL;
+
+ if (sata_dev_desc[dev].priv == NULL)
+ return -ENODEV;
+
+ probe_ent = (struct ahci_probe_ent *)sata_dev_desc[dev].priv;
+ port_mmio = (struct sata_port_regs *)probe_ent->port[port].port_mmio;
+
+ return readl(&(port_mmio->ssts)) && SATA_PORT_SSTS_DET_MASK;
+}
+
/*
* SATA interface between low level driver and command layer
*/
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_DM) := device.o lists.o root.o uclass.o util.o
+obj-y := device.o lists.o root.o uclass.o util.o
* a 'requested' sequence, and will be resolved (and ->seq updated)
* when the device is probed.
*/
- dev->req_seq = fdtdec_get_int(gd->fdt_blob, of_offset, "reg", -1);
dev->seq = -1;
+#ifdef CONFIG_OF_CONTROL
+ dev->req_seq = fdtdec_get_int(gd->fdt_blob, of_offset, "reg", -1);
+ if (!IS_ERR_VALUE(dev->req_seq))
+ dev->req_seq &= INT_MAX;
if (uc->uc_drv->name && of_offset != -1) {
fdtdec_get_alias_seq(gd->fdt_blob, uc->uc_drv->name, of_offset,
&dev->req_seq);
}
-
+#else
+ dev->req_seq = -1;
+#endif
if (!dev->platdata && drv->platdata_auto_alloc_size)
dev->flags |= DM_FLAG_ALLOC_PDATA;
unsigned char taxpd_mclk = 0;
/* Mode register set cycle time (tMRD). */
unsigned char tmrd_mclk;
+#if defined(CONFIG_SYS_FSL_DDR4) || defined(CONFIG_SYS_FSL_DDR3)
+ const unsigned int mclk_ps = get_memory_clk_period_ps();
+#endif
#ifdef CONFIG_SYS_FSL_DDR4
/* tXP=max(4nCK, 6ns) */
- int txp = max((get_memory_clk_period_ps() * 4), 6000); /* unit=ps */
+ int txp = max(mclk_ps * 4, 6000); /* unit=ps */
trwt_mclk = 2;
twrt_mclk = 1;
act_pd_exit_mclk = picos_to_mclk(txp);
*/
tmrd_mclk = max(24, picos_to_mclk(15000));
#elif defined(CONFIG_SYS_FSL_DDR3)
+ unsigned int data_rate = get_ddr_freq(0);
+ int txp;
/*
* (tXARD and tXARDS). Empirical?
* The DDR3 spec has not tXARD,
* we use the tXP instead of it.
- * tXP=max(3nCK, 7.5ns) for DDR3.
+ * tXP=max(3nCK, 7.5ns) for DDR3-800, 1066
+ * max(3nCK, 6ns) for DDR3-1333, 1600, 1866, 2133
* spec has not the tAXPD, we use
* tAXPD=1, need design to confirm.
*/
- int txp = max((get_memory_clk_period_ps() * 3), 7500); /* unit=ps */
- unsigned int data_rate = get_ddr_freq(0);
+ txp = max(mclk_ps * 3, (mclk_ps > 1540 ? 7500 : 6000));
+
tmrd_mclk = 4;
/* set the turnaround time */
unsigned char cke_pls;
/* Window for four activates (tFAW) */
unsigned short four_act;
+#ifdef CONFIG_SYS_FSL_DDR3
+ const unsigned int mclk_ps = get_memory_clk_period_ps();
+#endif
/* FIXME add check that this must be less than acttorw_mclk */
add_lat_mclk = additive_latency;
#ifdef CONFIG_SYS_FSL_DDR4
cpo = 0;
cke_pls = max(3, picos_to_mclk(5000));
+#elif defined(CONFIG_SYS_FSL_DDR3)
+ /*
+ * cke pulse = max(3nCK, 7.5ns) for DDR3-800
+ * max(3nCK, 5.625ns) for DDR3-1066, 1333
+ * max(3nCK, 5ns) for DDR3-1600, 1866, 2133
+ */
+ cke_pls = max(3, picos_to_mclk(mclk_ps > 1870 ? 7500 :
+ (mclk_ps > 1245 ? 5625 : 5000)));
#else
- cke_pls = picos_to_mclk(popts->tcke_clock_pulse_width_ps);
+ cke_pls = FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR;
#endif
-
four_act = picos_to_mclk(popts->tfaw_window_four_activates_ps);
ddr->timing_cfg_2 = (0
debug("FSLDDR: timing_cfg_9 = 0x%08x\n", ddr->timing_cfg_9);
}
+/* This function needs to be called after set_ddr_sdram_cfg() is called */
static void set_ddr_dq_mapping(fsl_ddr_cfg_regs_t *ddr,
const dimm_params_t *dimm_params)
{
+ unsigned int acc_ecc_en = (ddr->ddr_sdram_cfg >> 2) & 0x1;
+
ddr->dq_map_0 = ((dimm_params->dq_mapping[0] & 0x3F) << 26) |
((dimm_params->dq_mapping[1] & 0x3F) << 20) |
((dimm_params->dq_mapping[2] & 0x3F) << 14) |
((dimm_params->dq_mapping[15] & 0x3F) << 8) |
((dimm_params->dq_mapping[16] & 0x3F) << 2);
+ /* dq_map for ECC[4:7] is set to 0 if accumulated ECC is enabled */
ddr->dq_map_3 = ((dimm_params->dq_mapping[17] & 0x3F) << 26) |
((dimm_params->dq_mapping[8] & 0x3F) << 20) |
- ((dimm_params->dq_mapping[9] & 0x3F) << 14) |
+ (acc_ecc_en ? 0 :
+ (dimm_params->dq_mapping[9] & 0x3F) << 14) |
dimm_params->dq_mapping_ors;
debug("FSLDDR: dq_map_0 = 0x%08x\n", ddr->dq_map_0);
if (ip_rev > 0x40400)
unq_mrs_en = 1;
- if (ip_rev > 0x40700)
+ if ((ip_rev > 0x40700) && (popts->cswl_override != 0))
ddr->debug[18] = popts->cswl_override;
set_ddr_sdram_cfg_2(ddr, popts, unq_mrs_en);
#define spd_to_ps(mtb, ftb) \
(mtb * pdimm->mtb_ps + (ftb * pdimm->ftb_10th_ps) / 10)
/*
- * ddr_compute_dimm_parameters for DDR3 SPD
+ * ddr_compute_dimm_parameters for DDR4 SPD
*
* Compute DIMM parameters based upon the SPD information in spd.
* Writes the results to the dimm_params_t structure pointed by pdimm.
+ pdimm->ec_sdram_width;
pdimm->device_width = 1 << ((spd->organization & 0x7) + 2);
- /* These are the types defined by the JEDEC DDR3 SPD spec */
+ /* These are the types defined by the JEDEC SPD spec */
pdimm->mirrored_dimm = 0;
pdimm->registered_dimm = 0;
- switch (spd->module_type & DDR3_SPD_MODULETYPE_MASK) {
- case DDR3_SPD_MODULETYPE_RDIMM:
+ switch (spd->module_type & DDR4_SPD_MODULETYPE_MASK) {
+ case DDR4_SPD_MODULETYPE_RDIMM:
/* Registered/buffered DIMMs */
pdimm->registered_dimm = 1;
break;
- case DDR3_SPD_MODULETYPE_UDIMM:
- case DDR3_SPD_MODULETYPE_SO_DIMM:
+ case DDR4_SPD_MODULETYPE_UDIMM:
+ case DDR4_SPD_MODULETYPE_SO_DIMM:
/* Unbuffered DIMMs */
if (spd->mod_section.unbuffered.addr_mapping & 0x1)
pdimm->mirrored_dimm = 1;
* For example, 2GB on 666MT/s 64-bit bus takes about 402ms
* Let's wait for 800ms
*/
- bus_width = 3 - ((ddr->sdram_cfg & SDRAM_CFG_DBW_MASK)
+ bus_width = 3 - ((ddr_in32(&ddr->sdram_cfg) & SDRAM_CFG_DBW_MASK)
>> SDRAM_CFG_DBW_SHIFT);
timeout = ((total_gb_size_per_controller << (6 - bus_width)) * 100 /
(get_ddr_freq(0) >> 20)) << 2;
if (timeout <= 0)
printf("Waiting for D_INIT timeout. Memory may not work.\n");
-
}
CTRL_OPTIONS(rcw_2),
CTRL_OPTIONS(ddr_cdr1),
CTRL_OPTIONS(ddr_cdr2),
- CTRL_OPTIONS(tcke_clock_pulse_width_ps),
CTRL_OPTIONS(tfaw_window_four_activates_ps),
CTRL_OPTIONS(trwt_override),
CTRL_OPTIONS(trwt),
CTRL_OPTIONS(rcw_2),
CTRL_OPTIONS_HEX(ddr_cdr1),
CTRL_OPTIONS_HEX(ddr_cdr2),
- CTRL_OPTIONS(tcke_clock_pulse_width_ps),
CTRL_OPTIONS(tfaw_window_four_activates_ps),
CTRL_OPTIONS(trwt_override),
CTRL_OPTIONS(trwt),
void get_spd(generic_spd_eeprom_t *spd, u8 i2c_address);
void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd,
- unsigned int ctrl_num)
+ unsigned int ctrl_num, unsigned int dimm_slots_per_ctrl)
{
unsigned int i;
unsigned int i2c_address = 0;
return;
}
- for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+ for (i = 0; i < dimm_slots_per_ctrl; i++) {
i2c_address = spd_i2c_addr[ctrl_num][i];
get_spd(&(ctrl_dimms_spd[i]), i2c_address);
}
}
#else
void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd,
- unsigned int ctrl_num)
+ unsigned int ctrl_num, unsigned int dimm_slots_per_ctrl)
{
}
#endif /* SPD_EEPROM_ADDRESSx */
static unsigned long long __step_assign_addresses(fsl_ddr_info_t *pinfo,
unsigned int dbw_cap_adj[])
{
- int i, j;
+ unsigned int i, j;
unsigned long long total_mem, current_mem_base, total_ctlr_mem;
unsigned long long rank_density, ctlr_density = 0;
+ unsigned int first_ctrl = pinfo->first_ctrl;
+ unsigned int last_ctrl = first_ctrl + pinfo->num_ctrls - 1;
/*
* If a reduced data width is requested, but the SPD
* computed dimm capacities accordingly before
* assigning addresses.
*/
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ for (i = first_ctrl; i <= last_ctrl; i++) {
unsigned int found = 0;
switch (pinfo->memctl_opts[i].data_bus_width) {
debug("dbw_cap_adj[%d]=%d\n", i, dbw_cap_adj[i]);
}
- current_mem_base = CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY;
+ current_mem_base = pinfo->mem_base;
total_mem = 0;
- if (pinfo->memctl_opts[0].memctl_interleaving) {
- rank_density = pinfo->dimm_params[0][0].rank_density >>
- dbw_cap_adj[0];
- switch (pinfo->memctl_opts[0].ba_intlv_ctl &
+ if (pinfo->memctl_opts[first_ctrl].memctl_interleaving) {
+ rank_density = pinfo->dimm_params[first_ctrl][0].rank_density >>
+ dbw_cap_adj[first_ctrl];
+ switch (pinfo->memctl_opts[first_ctrl].ba_intlv_ctl &
FSL_DDR_CS0_CS1_CS2_CS3) {
case FSL_DDR_CS0_CS1_CS2_CS3:
ctlr_density = 4 * rank_density;
}
debug("rank density is 0x%llx, ctlr density is 0x%llx\n",
rank_density, ctlr_density);
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ for (i = first_ctrl; i <= last_ctrl; i++) {
if (pinfo->memctl_opts[i].memctl_interleaving) {
switch (pinfo->memctl_opts[i].memctl_interleaving_mode) {
case FSL_DDR_256B_INTERLEAVING:
* Simple linear assignment if memory
* controllers are not interleaved.
*/
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ for (i = first_ctrl; i <= last_ctrl; i++) {
total_ctlr_mem = 0;
pinfo->common_timing_params[i].base_address =
current_mem_base;
{
unsigned int i, j;
unsigned long long total_mem = 0;
- int assert_reset;
+ int assert_reset = 0;
+ unsigned int first_ctrl = pinfo->first_ctrl;
+ unsigned int last_ctrl = first_ctrl + pinfo->num_ctrls - 1;
+ __maybe_unused int retval;
+ __maybe_unused bool goodspd = false;
+ __maybe_unused int dimm_slots_per_ctrl = pinfo->dimm_slots_per_ctrl;
fsl_ddr_cfg_regs_t *ddr_reg = pinfo->fsl_ddr_config_reg;
common_timing_params_t *timing_params = pinfo->common_timing_params;
- assert_reset = board_need_mem_reset();
+ if (pinfo->board_need_mem_reset)
+ assert_reset = pinfo->board_need_mem_reset();
/* data bus width capacity adjust shift amount */
unsigned int dbw_capacity_adjust[CONFIG_NUM_DDR_CONTROLLERS];
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ for (i = first_ctrl; i <= last_ctrl; i++)
dbw_capacity_adjust[i] = 0;
- }
debug("starting at step %u (%s)\n",
start_step, step_to_string(start_step));
case STEP_GET_SPD:
#if defined(CONFIG_DDR_SPD) || defined(CONFIG_SPD_EEPROM)
/* STEP 1: Gather all DIMM SPD data */
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
- fsl_ddr_get_spd(pinfo->spd_installed_dimms[i], i);
+ for (i = first_ctrl; i <= last_ctrl; i++) {
+ fsl_ddr_get_spd(pinfo->spd_installed_dimms[i], i,
+ dimm_slots_per_ctrl);
}
case STEP_COMPUTE_DIMM_PARMS:
/* STEP 2: Compute DIMM parameters from SPD data */
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ for (i = first_ctrl; i <= last_ctrl; i++) {
for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) {
- unsigned int retval;
generic_spd_eeprom_t *spd =
&(pinfo->spd_installed_dimms[i][j]);
dimm_params_t *pdimm =
&(pinfo->dimm_params[i][j]);
-
retval = compute_dimm_parameters(spd, pdimm, i);
#ifdef CONFIG_SYS_DDR_RAW_TIMING
if (!i && !j && retval) {
printf("SPD error on controller %d! "
"Trying fallback to raw timing "
"calculation\n", i);
- fsl_ddr_get_dimm_params(pdimm, i, j);
+ retval = fsl_ddr_get_dimm_params(pdimm,
+ i, j);
}
#else
if (retval == 2) {
debug("Warning: compute_dimm_parameters"
" non-zero return value for memctl=%u "
"dimm=%u\n", i, j);
+ } else {
+ goodspd = true;
}
}
}
+ if (!goodspd) {
+ /*
+ * No valid SPD found
+ * Throw an error if this is for main memory, i.e.
+ * first_ctrl == 0. Otherwise, siliently return 0
+ * as the memory size.
+ */
+ if (first_ctrl == 0)
+ printf("Error: No valid SPD detected.\n");
+ return 0;
+ }
#elif defined(CONFIG_SYS_DDR_RAW_TIMING)
case STEP_COMPUTE_DIMM_PARMS:
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ for (i = first_ctrl; i <= last_ctrl; i++) {
for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) {
dimm_params_t *pdimm =
&(pinfo->dimm_params[i][j]);
* STEP 3: Compute a common set of timing parameters
* suitable for all of the DIMMs on each memory controller
*/
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ for (i = first_ctrl; i <= last_ctrl; i++) {
debug("Computing lowest common DIMM"
" parameters for memctl=%u\n", i);
compute_lowest_common_dimm_parameters(
case STEP_GATHER_OPTS:
/* STEP 4: Gather configuration requirements from user */
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ for (i = first_ctrl; i <= last_ctrl; i++) {
debug("Reloading memory controller "
"configuration options for memctl=%u\n", i);
/*
if (timing_params[i].all_dimms_registered)
assert_reset = 1;
}
- if (assert_reset) {
- debug("Asserting mem reset\n");
- board_assert_mem_reset();
+ if (assert_reset && !size_only) {
+ if (pinfo->board_mem_reset) {
+ debug("Asserting mem reset\n");
+ pinfo->board_mem_reset();
+ } else {
+ debug("Asserting mem reset missing\n");
+ }
}
case STEP_ASSIGN_ADDRESSES:
case STEP_COMPUTE_REGS:
/* STEP 6: compute controller register values */
debug("FSL Memory ctrl register computation\n");
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ for (i = first_ctrl; i <= last_ctrl; i++) {
if (timing_params[i].ndimms_present == 0) {
memset(&ddr_reg[i], 0,
sizeof(fsl_ddr_cfg_regs_t));
*/
unsigned int max_end = 0;
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ for (i = first_ctrl; i <= last_ctrl; i++) {
for (j = 0; j < CONFIG_CHIP_SELECTS_PER_CTRL; j++) {
fsl_ddr_cfg_regs_t *reg = &ddr_reg[i];
if (reg->cs[j].config & 0x80000000) {
}
total_mem = 1 + (((unsigned long long)max_end << 24ULL) |
- 0xFFFFFFULL) - CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY;
+ 0xFFFFFFULL) - pinfo->mem_base;
}
return total_mem;
}
-/*
- * fsl_ddr_sdram() -- this is the main function to be called by
- * initdram() in the board file.
- *
- * It returns amount of memory configured in bytes.
- */
-phys_size_t fsl_ddr_sdram(void)
+phys_size_t __fsl_ddr_sdram(fsl_ddr_info_t *pinfo)
{
- unsigned int i;
+ unsigned int i, first_ctrl, last_ctrl;
#ifdef CONFIG_PPC
unsigned int law_memctl = LAW_TRGT_IF_DDR_1;
#endif
unsigned long long total_memory;
- fsl_ddr_info_t info;
- int deassert_reset;
+ int deassert_reset = 0;
- /* Reset info structure. */
- memset(&info, 0, sizeof(fsl_ddr_info_t));
+ first_ctrl = pinfo->first_ctrl;
+ last_ctrl = first_ctrl + pinfo->num_ctrls - 1;
/* Compute it once normally. */
#ifdef CONFIG_FSL_DDR_INTERACTIVE
if (tstc() && (getc() == 'd')) { /* we got a key press of 'd' */
- total_memory = fsl_ddr_interactive(&info, 0);
+ total_memory = fsl_ddr_interactive(pinfo, 0);
} else if (fsl_ddr_interactive_env_var_exists()) {
- total_memory = fsl_ddr_interactive(&info, 1);
+ total_memory = fsl_ddr_interactive(pinfo, 1);
} else
#endif
- total_memory = fsl_ddr_compute(&info, STEP_GET_SPD, 0);
+ total_memory = fsl_ddr_compute(pinfo, STEP_GET_SPD, 0);
/* setup 3-way interleaving before enabling DDRC */
- if (info.memctl_opts[0].memctl_interleaving) {
- switch (info.memctl_opts[0].memctl_interleaving_mode) {
- case FSL_DDR_3WAY_1KB_INTERLEAVING:
- case FSL_DDR_3WAY_4KB_INTERLEAVING:
- case FSL_DDR_3WAY_8KB_INTERLEAVING:
- fsl_ddr_set_intl3r(
- info.memctl_opts[0].memctl_interleaving_mode);
- break;
- default:
- break;
- }
+ switch (pinfo->memctl_opts[first_ctrl].memctl_interleaving_mode) {
+ case FSL_DDR_3WAY_1KB_INTERLEAVING:
+ case FSL_DDR_3WAY_4KB_INTERLEAVING:
+ case FSL_DDR_3WAY_8KB_INTERLEAVING:
+ fsl_ddr_set_intl3r(
+ pinfo->memctl_opts[first_ctrl].
+ memctl_interleaving_mode);
+ break;
+ default:
+ break;
}
/*
* For non-registered DIMMs, initialization can go through but it is
* also OK to follow the same flow.
*/
- deassert_reset = board_need_mem_reset();
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
- if (info.common_timing_params[i].all_dimms_registered)
+ if (pinfo->board_need_mem_reset)
+ deassert_reset = pinfo->board_need_mem_reset();
+ for (i = first_ctrl; i <= last_ctrl; i++) {
+ if (pinfo->common_timing_params[i].all_dimms_registered)
deassert_reset = 1;
}
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ for (i = first_ctrl; i <= last_ctrl; i++) {
debug("Programming controller %u\n", i);
- if (info.common_timing_params[i].ndimms_present == 0) {
+ if (pinfo->common_timing_params[i].ndimms_present == 0) {
debug("No dimms present on controller %u; "
"skipping programming\n", i);
continue;
* The following call with step = 1 returns before enabling
* the controller. It has to finish with step = 2 later.
*/
- fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]), i,
+ fsl_ddr_set_memctl_regs(&(pinfo->fsl_ddr_config_reg[i]), i,
deassert_reset ? 1 : 0);
}
if (deassert_reset) {
/* Use board FPGA or GPIO to deassert reset signal */
- debug("Deasserting mem reset\n");
- board_deassert_mem_reset();
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ if (pinfo->board_mem_de_reset) {
+ debug("Deasserting mem reset\n");
+ pinfo->board_mem_de_reset();
+ } else {
+ debug("Deasserting mem reset missing\n");
+ }
+ for (i = first_ctrl; i <= last_ctrl; i++) {
/* Call with step = 2 to continue initialization */
- fsl_ddr_set_memctl_regs(&(info.fsl_ddr_config_reg[i]),
+ fsl_ddr_set_memctl_regs(&(pinfo->fsl_ddr_config_reg[i]),
i, 2);
}
}
#ifdef CONFIG_PPC
/* program LAWs */
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
- if (info.memctl_opts[i].memctl_interleaving) {
- switch (info.memctl_opts[i].memctl_interleaving_mode) {
+ for (i = first_ctrl; i <= last_ctrl; i++) {
+ if (pinfo->memctl_opts[i].memctl_interleaving) {
+ switch (pinfo->memctl_opts[i].
+ memctl_interleaving_mode) {
case FSL_DDR_CACHE_LINE_INTERLEAVING:
case FSL_DDR_PAGE_INTERLEAVING:
case FSL_DDR_BANK_INTERLEAVING:
case FSL_DDR_SUPERBANK_INTERLEAVING:
+ if (i % 2)
+ break;
if (i == 0) {
law_memctl = LAW_TRGT_IF_DDR_INTRLV;
- fsl_ddr_set_lawbar(&info.common_timing_params[i],
+ fsl_ddr_set_lawbar(
+ &pinfo->common_timing_params[i],
law_memctl, i);
- } else if (i == 2) {
+ }
+#if CONFIG_NUM_DDR_CONTROLLERS > 3
+ else if (i == 2) {
law_memctl = LAW_TRGT_IF_DDR_INTLV_34;
- fsl_ddr_set_lawbar(&info.common_timing_params[i],
+ fsl_ddr_set_lawbar(
+ &pinfo->common_timing_params[i],
law_memctl, i);
}
+#endif
break;
case FSL_DDR_3WAY_1KB_INTERLEAVING:
case FSL_DDR_3WAY_4KB_INTERLEAVING:
case FSL_DDR_3WAY_8KB_INTERLEAVING:
law_memctl = LAW_TRGT_IF_DDR_INTLV_123;
if (i == 0) {
- fsl_ddr_set_lawbar(&info.common_timing_params[i],
+ fsl_ddr_set_lawbar(
+ &pinfo->common_timing_params[i],
law_memctl, i);
}
break;
case FSL_DDR_4WAY_8KB_INTERLEAVING:
law_memctl = LAW_TRGT_IF_DDR_INTLV_1234;
if (i == 0)
- fsl_ddr_set_lawbar(&info.common_timing_params[i],
+ fsl_ddr_set_lawbar(
+ &pinfo->common_timing_params[i],
law_memctl, i);
/* place holder for future 4-way interleaving */
break;
default:
break;
}
- fsl_ddr_set_lawbar(&info.common_timing_params[i],
- law_memctl, i);
+ fsl_ddr_set_lawbar(&pinfo->common_timing_params[i],
+ law_memctl, i);
}
}
#endif
#if !defined(CONFIG_PHYS_64BIT)
/* Check for 4G or more. Bad. */
- if (total_memory >= (1ull << 32)) {
+ if ((first_ctrl == 0) && (total_memory >= (1ull << 32))) {
puts("Detected ");
print_size(total_memory, " of memory\n");
printf(" This U-Boot only supports < 4G of DDR\n");
}
/*
- * fsl_ddr_sdram_size() - This function only returns the size of the total
- * memory without setting ddr control registers.
+ * fsl_ddr_sdram(void) -- this is the main function to be
+ * called by initdram() in the board file.
+ *
+ * It returns amount of memory configured in bytes.
+ */
+phys_size_t fsl_ddr_sdram(void)
+{
+ fsl_ddr_info_t info;
+
+ /* Reset info structure. */
+ memset(&info, 0, sizeof(fsl_ddr_info_t));
+ info.mem_base = CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY;
+ info.first_ctrl = 0;
+ info.num_ctrls = CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS;
+ info.dimm_slots_per_ctrl = CONFIG_DIMM_SLOTS_PER_CTLR;
+ info.board_need_mem_reset = board_need_mem_reset;
+ info.board_mem_reset = board_assert_mem_reset;
+ info.board_mem_de_reset = board_deassert_mem_reset;
+
+ return __fsl_ddr_sdram(&info);
+}
+
+#ifdef CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
+phys_size_t fsl_other_ddr_sdram(unsigned long long base,
+ unsigned int first_ctrl,
+ unsigned int num_ctrls,
+ unsigned int dimm_slots_per_ctrl,
+ int (*board_need_reset)(void),
+ void (*board_reset)(void),
+ void (*board_de_reset)(void))
+{
+ fsl_ddr_info_t info;
+
+ /* Reset info structure. */
+ memset(&info, 0, sizeof(fsl_ddr_info_t));
+ info.mem_base = base;
+ info.first_ctrl = first_ctrl;
+ info.num_ctrls = num_ctrls;
+ info.dimm_slots_per_ctrl = dimm_slots_per_ctrl;
+ info.board_need_mem_reset = board_need_reset;
+ info.board_mem_reset = board_reset;
+ info.board_mem_de_reset = board_de_reset;
+
+ return __fsl_ddr_sdram(&info);
+}
+#endif
+
+/*
+ * fsl_ddr_sdram_size(first_ctrl, last_intlv) - This function only returns the
+ * size of the total memory without setting ddr control registers.
*/
phys_size_t
fsl_ddr_sdram_size(void)
unsigned long long total_memory = 0;
memset(&info, 0 , sizeof(fsl_ddr_info_t));
+ info.mem_base = CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY;
+ info.first_ctrl = 0;
+ info.num_ctrls = CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS;
+ info.dimm_slots_per_ctrl = CONFIG_DIMM_SLOTS_PER_CTLR;
+ info.board_need_mem_reset = NULL;
/* Compute it once normally. */
total_memory = fsl_ddr_compute(&info, STEP_GET_SPD, 1);
*/
popts->bstopre = 0x100;
- /* Minimum CKE pulse width -- tCKE(MIN) */
- popts->tcke_clock_pulse_width_ps
- = mclk_to_picos(FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR);
-
/*
* Window for four activates -- tFAW
*
unsigned int check_intlv, check_n_row_addr, check_n_col_addr;
unsigned long long check_rank_density;
struct dimm_params_s *dimm;
+ int first_ctrl = pinfo->first_ctrl;
+ int last_ctrl = first_ctrl + pinfo->num_ctrls - 1;
+
/*
* Check if all controllers are configured for memory
* controller interleaving. Identical dimms are recommended. At least
* the size, row and col address should be checked.
*/
j = 0;
- check_n_ranks = pinfo->dimm_params[0][0].n_ranks;
- check_rank_density = pinfo->dimm_params[0][0].rank_density;
- check_n_row_addr = pinfo->dimm_params[0][0].n_row_addr;
- check_n_col_addr = pinfo->dimm_params[0][0].n_col_addr;
- check_intlv = pinfo->memctl_opts[0].memctl_interleaving_mode;
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
+ check_n_ranks = pinfo->dimm_params[first_ctrl][0].n_ranks;
+ check_rank_density = pinfo->dimm_params[first_ctrl][0].rank_density;
+ check_n_row_addr = pinfo->dimm_params[first_ctrl][0].n_row_addr;
+ check_n_col_addr = pinfo->dimm_params[first_ctrl][0].n_col_addr;
+ check_intlv = pinfo->memctl_opts[first_ctrl].memctl_interleaving_mode;
+ for (i = first_ctrl; i <= last_ctrl; i++) {
dimm = &pinfo->dimm_params[i][0];
if (!pinfo->memctl_opts[i].memctl_interleaving) {
continue;
}
if (intlv_invalid) {
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++)
+ for (i = first_ctrl; i <= last_ctrl; i++)
pinfo->memctl_opts[i].memctl_interleaving = 0;
printf("Not all DIMMs are identical. "
"Memory controller interleaving disabled.\n");
}
debug("%d of %d controllers are interleaving.\n", j, k);
if (j && (j != k)) {
- for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++)
+ for (i = first_ctrl; i <= last_ctrl; i++)
pinfo->memctl_opts[i].memctl_interleaving = 0;
- printf("Not all controllers have compatible "
- "interleaving mode. All disabled.\n");
+ if ((last_ctrl - first_ctrl) > 1)
+ puts("Not all controllers have compatible interleaving mode. All disabled.\n");
}
}
debug("Checking interleaving options completed\n");
return val;
}
-void board_add_ram_info(int use_default)
+void print_ddr_info(unsigned int start_ctrl)
{
struct ccsr_ddr __iomem *ddr =
(struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);
int cas_lat;
#if CONFIG_NUM_DDR_CONTROLLERS >= 2
- if (!(sdram_cfg & SDRAM_CFG_MEM_EN)) {
+ if ((!(sdram_cfg & SDRAM_CFG_MEM_EN)) ||
+ (start_ctrl == 1)) {
ddr = (void __iomem *)CONFIG_SYS_FSL_DDR2_ADDR;
sdram_cfg = ddr_in32(&ddr->sdram_cfg);
}
#endif
#if CONFIG_NUM_DDR_CONTROLLERS >= 3
- if (!(sdram_cfg & SDRAM_CFG_MEM_EN)) {
+ if ((!(sdram_cfg & SDRAM_CFG_MEM_EN)) ||
+ (start_ctrl == 2)) {
ddr = (void __iomem *)CONFIG_SYS_FSL_DDR3_ADDR;
sdram_cfg = ddr_in32(&ddr->sdram_cfg);
}
#endif
+
+ if (!(sdram_cfg & SDRAM_CFG_MEM_EN)) {
+ puts(" (DDR not enabled)\n");
+ return;
+ }
+
puts(" (DDR");
switch ((sdram_cfg & SDRAM_CFG_SDRAM_TYPE_MASK) >>
SDRAM_CFG_SDRAM_TYPE_SHIFT) {
#endif
#endif
#if (CONFIG_NUM_DDR_CONTROLLERS >= 2)
- if (cs0_config & 0x20000000) {
+ if ((cs0_config & 0x20000000) && (start_ctrl == 0)) {
puts("\n");
puts(" DDR Controller Interleaving Mode: ");
}
}
}
+
+void __weak detail_board_ddr_info(void)
+{
+ print_ddr_info(0);
+}
+
+void board_add_ram_info(int use_default)
+{
+ detail_board_ddr_info();
+}
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_DM_DEMO) += demo-uclass.o demo-pdata.o
+obj-y += demo-uclass.o demo-pdata.o
obj-$(CONFIG_DM_DEMO_SIMPLE) += demo-simple.o
obj-$(CONFIG_DM_DEMO_SHAPE) += demo-shape.o
uint xfer_size;
while (count) {
- xfer_size = MIN(FSL_DMA_MAX_SIZE, count);
+ xfer_size = min(FSL_DMA_MAX_SIZE, count);
out_dma32(&dma->dar, (u32) (dest & 0xFFFFFFFF));
out_dma32(&dma->sar, (u32) (src & 0xFFFFFFFF));
int shift = (alen-1) * 8;
while (alen) {
- int transfer = MIN(alen, 2);
+ int transfer = min(alen, 2);
uchar buf[2];
bool is_last = alen <= transfer;
return 1;
while (len) {
- int transfer = MIN(len, 2);
+ int transfer = min(len, 2);
if (ihs_i2c_transfer(chip, buffer, transfer, read,
len <= transfer))
#endif
cfg->cfg.f_min = 400000;
- cfg->cfg.f_max = MIN(gd->arch.sdhc_clk, 52000000);
+ cfg->cfg.f_max = min(gd->arch.sdhc_clk, 52000000);
cfg->cfg.b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
--- /dev/null
+source "drivers/mtd/nand/Kconfig"
*truncated = 0;
*len_incl_bad = 0;
- if (!mtd->block_isbad) {
+ if (!mtd->_block_isbad) {
*len_incl_bad = length;
return;
}
block_len = mtd->erasesize - (offset & (mtd->erasesize - 1));
- if (!mtd->block_isbad(mtd, offset & ~(mtd->erasesize - 1)))
+ if (!mtd->_block_isbad(mtd, offset & ~(mtd->erasesize - 1)))
len_excl_bad += block_len;
*len_incl_bad += block_len;
--- /dev/null
+menu "NAND Device Support"
+
+if !SPL_BUILD
+
+config NAND_DENALI
+ bool "Support Denali NAND controller"
+ help
+ Enable support for the Denali NAND controller.
+
+config SYS_NAND_DENALI_64BIT
+ bool "Use 64-bit variant of Denali NAND controller"
+ depends on NAND_DENALI
+ help
+ The Denali NAND controller IP has some variations in terms of
+ the bus interface. The DMA setup sequence is completely differenct
+ between 32bit / 64bit AXI bus variants.
+
+ If your Denali NAND controller is the 64-bit variant, say Y.
+ Otherwise (32 bit), say N.
+
+config NAND_DENALI_SPARE_AREA_SKIP_BYTES
+ int "Number of bytes skipped in OOB area"
+ depends on NAND_DENALI
+ range 0 63
+ help
+ This option specifies the number of bytes to skip from the beginning
+ of OOB area before last ECC sector data starts. This is potentially
+ used to preserve the bad block marker in the OOB area.
+
+endif
+
+if SPL_BUILD
+
+config SPL_NAND_DENALI
+ bool "Support Denali NAND controller for SPL"
+ help
+ This is a small implementation of the Denali NAND controller
+ for use on SPL.
+
+endif
+
+endmenu
endif
obj-$(CONFIG_SPL_NAND_AM33XX_BCH) += am335x_spl_bch.o
+obj-$(CONFIG_SPL_NAND_DENALI) += denali_spl.o
obj-$(CONFIG_SPL_NAND_DOCG4) += docg4_spl.o
obj-$(CONFIG_SPL_NAND_SIMPLE) += nand_spl_simple.o
obj-$(CONFIG_SPL_NAND_LOAD) += nand_spl_load.o
obj-$(CONFIG_NAND_ATMEL) += atmel_nand.o
obj-$(CONFIG_DRIVER_NAND_BFIN) += bfin_nand.o
obj-$(CONFIG_NAND_DAVINCI) += davinci_nand.o
+obj-$(CONFIG_NAND_DENALI) += denali.o
obj-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_nand.o
obj-$(CONFIG_NAND_FSL_IFC) += fsl_ifc_nand.o
obj-$(CONFIG_NAND_FSL_UPM) += fsl_upm.o
NAND_CTRL_ALE | NAND_CTRL_CHANGE); /* A[7:0] */
hwctrl(&nand_info[0], (offs >> 8) & 0xff, NAND_CTRL_ALE); /* A[11:9] */
/* Row address */
- hwctrl(&nand_info[0], (page_addr & 0xff), NAND_CTRL_ALE); /* A[19:12] */
- hwctrl(&nand_info[0], ((page_addr >> 8) & 0xff),
+ if (cmd != NAND_CMD_RNDOUT) {
+ hwctrl(&nand_info[0], (page_addr & 0xff),
+ NAND_CTRL_ALE); /* A[19:12] */
+ hwctrl(&nand_info[0], ((page_addr >> 8) & 0xff),
NAND_CTRL_ALE); /* A[27:20] */
#ifdef CONFIG_SYS_NAND_5_ADDR_CYCLE
- /* One more address cycle for devices > 128MiB */
- hwctrl(&nand_info[0], (page_addr >> 16) & 0x0f,
+ /* One more address cycle for devices > 128MiB */
+ hwctrl(&nand_info[0], (page_addr >> 16) & 0x0f,
NAND_CTRL_ALE); /* A[31:28] */
#endif
+ }
+
hwctrl(&nand_info[0], NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
if (cmd == NAND_CMD_READ0) {
/* Fill odd syndromes */
for (i = 0; i < host->pmecc_corr_cap; i++) {
- value = readl(&host->pmecc->rem_port[sector].rem[i / 2]);
+ value = pmecc_readl(host->pmecc, rem_port[sector].rem[i / 2]);
if (i & 1)
value >>= 16;
value &= 0xffff;
int16_t *smu = host->pmecc_smu;
int timeout = PMECC_MAX_TIMEOUT_US;
- writel(PMERRLOC_DISABLE, &host->pmerrloc->eldis);
+ pmecc_writel(host->pmerrloc, eldis, PMERRLOC_DISABLE);
for (i = 0; i <= host->pmecc_lmu[cap + 1] >> 1; i++) {
- writel(smu[(cap + 1) * num + i], &host->pmerrloc->sigma[i]);
+ pmecc_writel(host->pmerrloc, sigma[i],
+ smu[(cap + 1) * num + i]);
err_nbr++;
}
if (sector_size == 1024)
val |= PMERRLOC_ELCFG_SECTOR_1024;
- writel(val, &host->pmerrloc->elcfg);
- writel(sector_size * 8 + host->pmecc_degree * cap,
- &host->pmerrloc->elen);
+ pmecc_writel(host->pmerrloc, elcfg, val);
+ pmecc_writel(host->pmerrloc, elen,
+ sector_size * 8 + host->pmecc_degree * cap);
while (--timeout) {
- if (readl(&host->pmerrloc->elisr) & PMERRLOC_CALC_DONE)
+ if (pmecc_readl(host->pmerrloc, elisr) & PMERRLOC_CALC_DONE)
break;
WATCHDOG_RESET();
udelay(1);
return -1;
}
- roots_nbr = (readl(&host->pmerrloc->elisr) & PMERRLOC_ERR_NUM_MASK)
+ roots_nbr = (pmecc_readl(host->pmerrloc, elisr) & PMERRLOC_ERR_NUM_MASK)
>> 8;
/* Number of roots == degree of smu hence <= cap */
if (roots_nbr == host->pmecc_lmu[cap + 1] >> 1)
sector_size = host->pmecc_sector_size;
while (err_nbr) {
- tmp = readl(&host->pmerrloc->el[i]) - 1;
+ tmp = pmecc_readl(host->pmerrloc, el[i]) - 1;
byte_pos = tmp / 8;
bit_pos = tmp % 8;
pos = i * host->pmecc_bytes_per_sector + j;
chip->oob_poi[eccpos[pos]] =
- readb(&host->pmecc->ecc_port[i].ecc[j]);
+ pmecc_readb(host->pmecc, ecc_port[i].ecc[j]);
}
}
chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
return -ENOMEM;
}
+ nand->options |= NAND_NO_SUBPAGE_WRITE;
nand->ecc.read_page = atmel_nand_pmecc_read_page;
nand->ecc.write_page = atmel_nand_pmecc_write_page;
nand->ecc.strength = cap;
#define pmecc_readl(addr, reg) \
readl(&addr->reg)
+#define pmecc_readb(addr, reg) \
+ readb(&addr->reg)
+
#define pmecc_writel(addr, reg, value) \
writel((value), &addr->reg)
* @raw: use _raw version of write_page
*/
static int nand_davinci_write_page(struct mtd_info *mtd, struct nand_chip *chip,
+ uint32_t offset, int data_len,
const uint8_t *buf, int oob_required,
int page, int cached, int raw)
{
--- /dev/null
+/*
+ * Copyright (C) 2014 Panasonic Corporation
+ * Copyright (C) 2013-2014, Altera Corporation <www.altera.com>
+ * Copyright (C) 2009-2010, Intel Corporation and its suppliers.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <nand.h>
+#include <asm/errno.h>
+#include <asm/io.h>
+
+#include "denali.h"
+
+#define NAND_DEFAULT_TIMINGS -1
+
+static int onfi_timing_mode = NAND_DEFAULT_TIMINGS;
+
+/* We define a macro here that combines all interrupts this driver uses into
+ * a single constant value, for convenience. */
+#define DENALI_IRQ_ALL (INTR_STATUS__DMA_CMD_COMP | \
+ INTR_STATUS__ECC_TRANSACTION_DONE | \
+ INTR_STATUS__ECC_ERR | \
+ INTR_STATUS__PROGRAM_FAIL | \
+ INTR_STATUS__LOAD_COMP | \
+ INTR_STATUS__PROGRAM_COMP | \
+ INTR_STATUS__TIME_OUT | \
+ INTR_STATUS__ERASE_FAIL | \
+ INTR_STATUS__RST_COMP | \
+ INTR_STATUS__ERASE_COMP | \
+ INTR_STATUS__ECC_UNCOR_ERR | \
+ INTR_STATUS__INT_ACT | \
+ INTR_STATUS__LOCKED_BLK)
+
+/* indicates whether or not the internal value for the flash bank is
+ * valid or not */
+#define CHIP_SELECT_INVALID -1
+
+#define SUPPORT_8BITECC 1
+
+/*
+ * this macro allows us to convert from an MTD structure to our own
+ * device context (denali) structure.
+ */
+#define mtd_to_denali(m) (((struct nand_chip *)mtd->priv)->priv)
+
+/* These constants are defined by the driver to enable common driver
+ * configuration options. */
+#define SPARE_ACCESS 0x41
+#define MAIN_ACCESS 0x42
+#define MAIN_SPARE_ACCESS 0x43
+
+#define DENALI_UNLOCK_START 0x10
+#define DENALI_UNLOCK_END 0x11
+#define DENALI_LOCK 0x21
+#define DENALI_LOCK_TIGHT 0x31
+#define DENALI_BUFFER_LOAD 0x60
+#define DENALI_BUFFER_WRITE 0x62
+
+#define DENALI_READ 0
+#define DENALI_WRITE 0x100
+
+/* types of device accesses. We can issue commands and get status */
+#define COMMAND_CYCLE 0
+#define ADDR_CYCLE 1
+#define STATUS_CYCLE 2
+
+/* this is a helper macro that allows us to
+ * format the bank into the proper bits for the controller */
+#define BANK(x) ((x) << 24)
+
+/* Interrupts are cleared by writing a 1 to the appropriate status bit */
+static inline void clear_interrupt(struct denali_nand_info *denali,
+ uint32_t irq_mask)
+{
+ uint32_t intr_status_reg;
+
+ intr_status_reg = INTR_STATUS(denali->flash_bank);
+
+ writel(irq_mask, denali->flash_reg + intr_status_reg);
+}
+
+static uint32_t read_interrupt_status(struct denali_nand_info *denali)
+{
+ uint32_t intr_status_reg;
+
+ intr_status_reg = INTR_STATUS(denali->flash_bank);
+
+ return readl(denali->flash_reg + intr_status_reg);
+}
+
+static void clear_interrupts(struct denali_nand_info *denali)
+{
+ uint32_t status;
+
+ status = read_interrupt_status(denali);
+ clear_interrupt(denali, status);
+
+ denali->irq_status = 0;
+}
+
+static void denali_irq_enable(struct denali_nand_info *denali,
+ uint32_t int_mask)
+{
+ int i;
+
+ for (i = 0; i < denali->max_banks; ++i)
+ writel(int_mask, denali->flash_reg + INTR_EN(i));
+}
+
+static uint32_t wait_for_irq(struct denali_nand_info *denali, uint32_t irq_mask)
+{
+ unsigned long timeout = 1000000;
+ uint32_t intr_status;
+
+ do {
+ intr_status = read_interrupt_status(denali) & DENALI_IRQ_ALL;
+ if (intr_status & irq_mask) {
+ denali->irq_status &= ~irq_mask;
+ /* our interrupt was detected */
+ break;
+ }
+ udelay(1);
+ timeout--;
+ } while (timeout != 0);
+
+ if (timeout == 0) {
+ /* timeout */
+ printf("Denali timeout with interrupt status %08x\n",
+ read_interrupt_status(denali));
+ intr_status = 0;
+ }
+ return intr_status;
+}
+
+/*
+ * Certain operations for the denali NAND controller use an indexed mode to
+ * read/write data. The operation is performed by writing the address value
+ * of the command to the device memory followed by the data. This function
+ * abstracts this common operation.
+*/
+static void index_addr(struct denali_nand_info *denali,
+ uint32_t address, uint32_t data)
+{
+ writel(address, denali->flash_mem + INDEX_CTRL_REG);
+ writel(data, denali->flash_mem + INDEX_DATA_REG);
+}
+
+/* Perform an indexed read of the device */
+static void index_addr_read_data(struct denali_nand_info *denali,
+ uint32_t address, uint32_t *pdata)
+{
+ writel(address, denali->flash_mem + INDEX_CTRL_REG);
+ *pdata = readl(denali->flash_mem + INDEX_DATA_REG);
+}
+
+/* We need to buffer some data for some of the NAND core routines.
+ * The operations manage buffering that data. */
+static void reset_buf(struct denali_nand_info *denali)
+{
+ denali->buf.head = 0;
+ denali->buf.tail = 0;
+}
+
+static void write_byte_to_buf(struct denali_nand_info *denali, uint8_t byte)
+{
+ denali->buf.buf[denali->buf.tail++] = byte;
+}
+
+/* resets a specific device connected to the core */
+static void reset_bank(struct denali_nand_info *denali)
+{
+ uint32_t irq_status;
+ uint32_t irq_mask = INTR_STATUS__RST_COMP |
+ INTR_STATUS__TIME_OUT;
+
+ clear_interrupts(denali);
+
+ writel(1 << denali->flash_bank, denali->flash_reg + DEVICE_RESET);
+
+ irq_status = wait_for_irq(denali, irq_mask);
+ if (irq_status & INTR_STATUS__TIME_OUT)
+ debug("reset bank failed.\n");
+}
+
+/* Reset the flash controller */
+static uint32_t denali_nand_reset(struct denali_nand_info *denali)
+{
+ uint32_t i;
+
+ for (i = 0; i < denali->max_banks; i++)
+ writel(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT,
+ denali->flash_reg + INTR_STATUS(i));
+
+ for (i = 0; i < denali->max_banks; i++) {
+ writel(1 << i, denali->flash_reg + DEVICE_RESET);
+ while (!(readl(denali->flash_reg + INTR_STATUS(i)) &
+ (INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT)))
+ if (readl(denali->flash_reg + INTR_STATUS(i)) &
+ INTR_STATUS__TIME_OUT)
+ debug("NAND Reset operation timed out on bank"
+ " %d\n", i);
+ }
+
+ for (i = 0; i < denali->max_banks; i++)
+ writel(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT,
+ denali->flash_reg + INTR_STATUS(i));
+
+ return 0;
+}
+
+/*
+ * this routine calculates the ONFI timing values for a given mode and
+ * programs the clocking register accordingly. The mode is determined by
+ * the get_onfi_nand_para routine.
+ */
+static void nand_onfi_timing_set(struct denali_nand_info *denali,
+ uint16_t mode)
+{
+ uint32_t trea[6] = {40, 30, 25, 20, 20, 16};
+ uint32_t trp[6] = {50, 25, 17, 15, 12, 10};
+ uint32_t treh[6] = {30, 15, 15, 10, 10, 7};
+ uint32_t trc[6] = {100, 50, 35, 30, 25, 20};
+ uint32_t trhoh[6] = {0, 15, 15, 15, 15, 15};
+ uint32_t trloh[6] = {0, 0, 0, 0, 5, 5};
+ uint32_t tcea[6] = {100, 45, 30, 25, 25, 25};
+ uint32_t tadl[6] = {200, 100, 100, 100, 70, 70};
+ uint32_t trhw[6] = {200, 100, 100, 100, 100, 100};
+ uint32_t trhz[6] = {200, 100, 100, 100, 100, 100};
+ uint32_t twhr[6] = {120, 80, 80, 60, 60, 60};
+ uint32_t tcs[6] = {70, 35, 25, 25, 20, 15};
+
+ uint32_t tclsrising = 1;
+ uint32_t data_invalid_rhoh, data_invalid_rloh, data_invalid;
+ uint32_t dv_window = 0;
+ uint32_t en_lo, en_hi;
+ uint32_t acc_clks;
+ uint32_t addr_2_data, re_2_we, re_2_re, we_2_re, cs_cnt;
+
+ en_lo = DIV_ROUND_UP(trp[mode], CLK_X);
+ en_hi = DIV_ROUND_UP(treh[mode], CLK_X);
+ if ((en_hi * CLK_X) < (treh[mode] + 2))
+ en_hi++;
+
+ if ((en_lo + en_hi) * CLK_X < trc[mode])
+ en_lo += DIV_ROUND_UP((trc[mode] - (en_lo + en_hi) * CLK_X),
+ CLK_X);
+
+ if ((en_lo + en_hi) < CLK_MULTI)
+ en_lo += CLK_MULTI - en_lo - en_hi;
+
+ while (dv_window < 8) {
+ data_invalid_rhoh = en_lo * CLK_X + trhoh[mode];
+
+ data_invalid_rloh = (en_lo + en_hi) * CLK_X + trloh[mode];
+
+ data_invalid =
+ data_invalid_rhoh <
+ data_invalid_rloh ? data_invalid_rhoh : data_invalid_rloh;
+
+ dv_window = data_invalid - trea[mode];
+
+ if (dv_window < 8)
+ en_lo++;
+ }
+
+ acc_clks = DIV_ROUND_UP(trea[mode], CLK_X);
+
+ while (((acc_clks * CLK_X) - trea[mode]) < 3)
+ acc_clks++;
+
+ if ((data_invalid - acc_clks * CLK_X) < 2)
+ debug("%s, Line %d: Warning!\n", __FILE__, __LINE__);
+
+ addr_2_data = DIV_ROUND_UP(tadl[mode], CLK_X);
+ re_2_we = DIV_ROUND_UP(trhw[mode], CLK_X);
+ re_2_re = DIV_ROUND_UP(trhz[mode], CLK_X);
+ we_2_re = DIV_ROUND_UP(twhr[mode], CLK_X);
+ cs_cnt = DIV_ROUND_UP((tcs[mode] - trp[mode]), CLK_X);
+ if (!tclsrising)
+ cs_cnt = DIV_ROUND_UP(tcs[mode], CLK_X);
+ if (cs_cnt == 0)
+ cs_cnt = 1;
+
+ if (tcea[mode]) {
+ while (((cs_cnt * CLK_X) + trea[mode]) < tcea[mode])
+ cs_cnt++;
+ }
+
+ /* Sighting 3462430: Temporary hack for MT29F128G08CJABAWP:B */
+ if ((readl(denali->flash_reg + MANUFACTURER_ID) == 0) &&
+ (readl(denali->flash_reg + DEVICE_ID) == 0x88))
+ acc_clks = 6;
+
+ writel(acc_clks, denali->flash_reg + ACC_CLKS);
+ writel(re_2_we, denali->flash_reg + RE_2_WE);
+ writel(re_2_re, denali->flash_reg + RE_2_RE);
+ writel(we_2_re, denali->flash_reg + WE_2_RE);
+ writel(addr_2_data, denali->flash_reg + ADDR_2_DATA);
+ writel(en_lo, denali->flash_reg + RDWR_EN_LO_CNT);
+ writel(en_hi, denali->flash_reg + RDWR_EN_HI_CNT);
+ writel(cs_cnt, denali->flash_reg + CS_SETUP_CNT);
+}
+
+/* queries the NAND device to see what ONFI modes it supports. */
+static uint32_t get_onfi_nand_para(struct denali_nand_info *denali)
+{
+ int i;
+ /*
+ * we needn't to do a reset here because driver has already
+ * reset all the banks before
+ */
+ if (!(readl(denali->flash_reg + ONFI_TIMING_MODE) &
+ ONFI_TIMING_MODE__VALUE))
+ return -EIO;
+
+ for (i = 5; i > 0; i--) {
+ if (readl(denali->flash_reg + ONFI_TIMING_MODE) &
+ (0x01 << i))
+ break;
+ }
+
+ nand_onfi_timing_set(denali, i);
+
+ /* By now, all the ONFI devices we know support the page cache */
+ /* rw feature. So here we enable the pipeline_rw_ahead feature */
+ return 0;
+}
+
+static void get_samsung_nand_para(struct denali_nand_info *denali,
+ uint8_t device_id)
+{
+ if (device_id == 0xd3) { /* Samsung K9WAG08U1A */
+ /* Set timing register values according to datasheet */
+ writel(5, denali->flash_reg + ACC_CLKS);
+ writel(20, denali->flash_reg + RE_2_WE);
+ writel(12, denali->flash_reg + WE_2_RE);
+ writel(14, denali->flash_reg + ADDR_2_DATA);
+ writel(3, denali->flash_reg + RDWR_EN_LO_CNT);
+ writel(2, denali->flash_reg + RDWR_EN_HI_CNT);
+ writel(2, denali->flash_reg + CS_SETUP_CNT);
+ }
+}
+
+static void get_toshiba_nand_para(struct denali_nand_info *denali)
+{
+ uint32_t tmp;
+
+ /* Workaround to fix a controller bug which reports a wrong */
+ /* spare area size for some kind of Toshiba NAND device */
+ if ((readl(denali->flash_reg + DEVICE_MAIN_AREA_SIZE) == 4096) &&
+ (readl(denali->flash_reg + DEVICE_SPARE_AREA_SIZE) == 64)) {
+ writel(216, denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
+ tmp = readl(denali->flash_reg + DEVICES_CONNECTED) *
+ readl(denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
+ writel(tmp, denali->flash_reg + LOGICAL_PAGE_SPARE_SIZE);
+ }
+}
+
+static void get_hynix_nand_para(struct denali_nand_info *denali,
+ uint8_t device_id)
+{
+ uint32_t main_size, spare_size;
+
+ switch (device_id) {
+ case 0xD5: /* Hynix H27UAG8T2A, H27UBG8U5A or H27UCG8VFA */
+ case 0xD7: /* Hynix H27UDG8VEM, H27UCG8UDM or H27UCG8V5A */
+ writel(128, denali->flash_reg + PAGES_PER_BLOCK);
+ writel(4096, denali->flash_reg + DEVICE_MAIN_AREA_SIZE);
+ writel(224, denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
+ main_size = 4096 *
+ readl(denali->flash_reg + DEVICES_CONNECTED);
+ spare_size = 224 *
+ readl(denali->flash_reg + DEVICES_CONNECTED);
+ writel(main_size, denali->flash_reg + LOGICAL_PAGE_DATA_SIZE);
+ writel(spare_size, denali->flash_reg + LOGICAL_PAGE_SPARE_SIZE);
+ writel(0, denali->flash_reg + DEVICE_WIDTH);
+ break;
+ default:
+ debug("Spectra: Unknown Hynix NAND (Device ID: 0x%x)."
+ "Will use default parameter values instead.\n",
+ device_id);
+ }
+}
+
+/*
+ * determines how many NAND chips are connected to the controller. Note for
+ * Intel CE4100 devices we don't support more than one device.
+ */
+static void find_valid_banks(struct denali_nand_info *denali)
+{
+ uint32_t id[denali->max_banks];
+ int i;
+
+ denali->total_used_banks = 1;
+ for (i = 0; i < denali->max_banks; i++) {
+ index_addr(denali, (uint32_t)(MODE_11 | (i << 24) | 0), 0x90);
+ index_addr(denali, (uint32_t)(MODE_11 | (i << 24) | 1), 0);
+ index_addr_read_data(denali,
+ (uint32_t)(MODE_11 | (i << 24) | 2),
+ &id[i]);
+
+ if (i == 0) {
+ if (!(id[i] & 0x0ff))
+ break;
+ } else {
+ if ((id[i] & 0x0ff) == (id[0] & 0x0ff))
+ denali->total_used_banks++;
+ else
+ break;
+ }
+ }
+}
+
+/*
+ * Use the configuration feature register to determine the maximum number of
+ * banks that the hardware supports.
+ */
+static void detect_max_banks(struct denali_nand_info *denali)
+{
+ uint32_t features = readl(denali->flash_reg + FEATURES);
+ denali->max_banks = 2 << (features & FEATURES__N_BANKS);
+}
+
+static void detect_partition_feature(struct denali_nand_info *denali)
+{
+ /*
+ * For MRST platform, denali->fwblks represent the
+ * number of blocks firmware is taken,
+ * FW is in protect partition and MTD driver has no
+ * permission to access it. So let driver know how many
+ * blocks it can't touch.
+ */
+ if (readl(denali->flash_reg + FEATURES) & FEATURES__PARTITION) {
+ if ((readl(denali->flash_reg + PERM_SRC_ID(1)) &
+ PERM_SRC_ID__SRCID) == SPECTRA_PARTITION_ID) {
+ denali->fwblks =
+ ((readl(denali->flash_reg + MIN_MAX_BANK(1)) &
+ MIN_MAX_BANK__MIN_VALUE) *
+ denali->blksperchip)
+ +
+ (readl(denali->flash_reg + MIN_BLK_ADDR(1)) &
+ MIN_BLK_ADDR__VALUE);
+ } else {
+ denali->fwblks = SPECTRA_START_BLOCK;
+ }
+ } else {
+ denali->fwblks = SPECTRA_START_BLOCK;
+ }
+}
+
+static uint32_t denali_nand_timing_set(struct denali_nand_info *denali)
+{
+ uint32_t id_bytes[5], addr;
+ uint8_t i, maf_id, device_id;
+
+ /* Use read id method to get device ID and other
+ * params. For some NAND chips, controller can't
+ * report the correct device ID by reading from
+ * DEVICE_ID register
+ * */
+ addr = (uint32_t)MODE_11 | BANK(denali->flash_bank);
+ index_addr(denali, (uint32_t)addr | 0, 0x90);
+ index_addr(denali, (uint32_t)addr | 1, 0);
+ for (i = 0; i < 5; i++)
+ index_addr_read_data(denali, addr | 2, &id_bytes[i]);
+ maf_id = id_bytes[0];
+ device_id = id_bytes[1];
+
+ if (readl(denali->flash_reg + ONFI_DEVICE_NO_OF_LUNS) &
+ ONFI_DEVICE_NO_OF_LUNS__ONFI_DEVICE) { /* ONFI 1.0 NAND */
+ if (get_onfi_nand_para(denali))
+ return -EIO;
+ } else if (maf_id == 0xEC) { /* Samsung NAND */
+ get_samsung_nand_para(denali, device_id);
+ } else if (maf_id == 0x98) { /* Toshiba NAND */
+ get_toshiba_nand_para(denali);
+ } else if (maf_id == 0xAD) { /* Hynix NAND */
+ get_hynix_nand_para(denali, device_id);
+ }
+
+ find_valid_banks(denali);
+
+ detect_partition_feature(denali);
+
+ /* If the user specified to override the default timings
+ * with a specific ONFI mode, we apply those changes here.
+ */
+ if (onfi_timing_mode != NAND_DEFAULT_TIMINGS)
+ nand_onfi_timing_set(denali, onfi_timing_mode);
+
+ return 0;
+}
+
+/* validation function to verify that the controlling software is making
+ * a valid request
+ */
+static inline bool is_flash_bank_valid(int flash_bank)
+{
+ return flash_bank >= 0 && flash_bank < 4;
+}
+
+static void denali_irq_init(struct denali_nand_info *denali)
+{
+ uint32_t int_mask = 0;
+ int i;
+
+ /* Disable global interrupts */
+ writel(0, denali->flash_reg + GLOBAL_INT_ENABLE);
+
+ int_mask = DENALI_IRQ_ALL;
+
+ /* Clear all status bits */
+ for (i = 0; i < denali->max_banks; ++i)
+ writel(0xFFFF, denali->flash_reg + INTR_STATUS(i));
+
+ denali_irq_enable(denali, int_mask);
+}
+
+/* This helper function setups the registers for ECC and whether or not
+ * the spare area will be transferred. */
+static void setup_ecc_for_xfer(struct denali_nand_info *denali, bool ecc_en,
+ bool transfer_spare)
+{
+ int ecc_en_flag = 0, transfer_spare_flag = 0;
+
+ /* set ECC, transfer spare bits if needed */
+ ecc_en_flag = ecc_en ? ECC_ENABLE__FLAG : 0;
+ transfer_spare_flag = transfer_spare ? TRANSFER_SPARE_REG__FLAG : 0;
+
+ /* Enable spare area/ECC per user's request. */
+ writel(ecc_en_flag, denali->flash_reg + ECC_ENABLE);
+ /* applicable for MAP01 only */
+ writel(transfer_spare_flag, denali->flash_reg + TRANSFER_SPARE_REG);
+}
+
+/* sends a pipeline command operation to the controller. See the Denali NAND
+ * controller's user guide for more information (section 4.2.3.6).
+ */
+static int denali_send_pipeline_cmd(struct denali_nand_info *denali,
+ bool ecc_en, bool transfer_spare,
+ int access_type, int op)
+{
+ uint32_t addr, cmd, irq_status;
+ static uint32_t page_count = 1;
+
+ setup_ecc_for_xfer(denali, ecc_en, transfer_spare);
+
+ /* clear interrupts */
+ clear_interrupts(denali);
+
+ addr = BANK(denali->flash_bank) | denali->page;
+
+ /* setup the acccess type */
+ cmd = MODE_10 | addr;
+ index_addr(denali, cmd, access_type);
+
+ /* setup the pipeline command */
+ index_addr(denali, cmd, 0x2000 | op | page_count);
+
+ cmd = MODE_01 | addr;
+ writel(cmd, denali->flash_mem + INDEX_CTRL_REG);
+
+ if (op == DENALI_READ) {
+ /* wait for command to be accepted */
+ irq_status = wait_for_irq(denali, INTR_STATUS__LOAD_COMP);
+
+ if (irq_status == 0)
+ return -EIO;
+ }
+
+ return 0;
+}
+
+/* helper function that simply writes a buffer to the flash */
+static int write_data_to_flash_mem(struct denali_nand_info *denali,
+ const uint8_t *buf, int len)
+{
+ uint32_t i = 0, *buf32;
+
+ /* verify that the len is a multiple of 4. see comment in
+ * read_data_from_flash_mem() */
+ BUG_ON((len % 4) != 0);
+
+ /* write the data to the flash memory */
+ buf32 = (uint32_t *)buf;
+ for (i = 0; i < len / 4; i++)
+ writel(*buf32++, denali->flash_mem + INDEX_DATA_REG);
+ return i * 4; /* intent is to return the number of bytes read */
+}
+
+/* helper function that simply reads a buffer from the flash */
+static int read_data_from_flash_mem(struct denali_nand_info *denali,
+ uint8_t *buf, int len)
+{
+ uint32_t i, *buf32;
+
+ /*
+ * we assume that len will be a multiple of 4, if not
+ * it would be nice to know about it ASAP rather than
+ * have random failures...
+ * This assumption is based on the fact that this
+ * function is designed to be used to read flash pages,
+ * which are typically multiples of 4...
+ */
+
+ BUG_ON((len % 4) != 0);
+
+ /* transfer the data from the flash */
+ buf32 = (uint32_t *)buf;
+ for (i = 0; i < len / 4; i++)
+ *buf32++ = readl(denali->flash_mem + INDEX_DATA_REG);
+
+ return i * 4; /* intent is to return the number of bytes read */
+}
+
+static void denali_mode_main_access(struct denali_nand_info *denali)
+{
+ uint32_t addr, cmd;
+
+ addr = BANK(denali->flash_bank) | denali->page;
+ cmd = MODE_10 | addr;
+ index_addr(denali, cmd, MAIN_ACCESS);
+}
+
+static void denali_mode_main_spare_access(struct denali_nand_info *denali)
+{
+ uint32_t addr, cmd;
+
+ addr = BANK(denali->flash_bank) | denali->page;
+ cmd = MODE_10 | addr;
+ index_addr(denali, cmd, MAIN_SPARE_ACCESS);
+}
+
+/* writes OOB data to the device */
+static int write_oob_data(struct mtd_info *mtd, uint8_t *buf, int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint32_t irq_status;
+ uint32_t irq_mask = INTR_STATUS__PROGRAM_COMP |
+ INTR_STATUS__PROGRAM_FAIL;
+ int status = 0;
+
+ denali->page = page;
+
+ if (denali_send_pipeline_cmd(denali, false, true, SPARE_ACCESS,
+ DENALI_WRITE) == 0) {
+ write_data_to_flash_mem(denali, buf, mtd->oobsize);
+
+ /* wait for operation to complete */
+ irq_status = wait_for_irq(denali, irq_mask);
+
+ if (irq_status == 0) {
+ dev_err(denali->dev, "OOB write failed\n");
+ status = -EIO;
+ }
+ } else {
+ printf("unable to send pipeline command\n");
+ status = -EIO;
+ }
+ return status;
+}
+
+/* reads OOB data from the device */
+static void read_oob_data(struct mtd_info *mtd, uint8_t *buf, int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint32_t irq_mask = INTR_STATUS__LOAD_COMP,
+ irq_status = 0, addr = 0x0, cmd = 0x0;
+
+ denali->page = page;
+
+ if (denali_send_pipeline_cmd(denali, false, true, SPARE_ACCESS,
+ DENALI_READ) == 0) {
+ read_data_from_flash_mem(denali, buf, mtd->oobsize);
+
+ /* wait for command to be accepted
+ * can always use status0 bit as the mask is identical for each
+ * bank. */
+ irq_status = wait_for_irq(denali, irq_mask);
+
+ if (irq_status == 0)
+ printf("page on OOB timeout %d\n", denali->page);
+
+ /* We set the device back to MAIN_ACCESS here as I observed
+ * instability with the controller if you do a block erase
+ * and the last transaction was a SPARE_ACCESS. Block erase
+ * is reliable (according to the MTD test infrastructure)
+ * if you are in MAIN_ACCESS.
+ */
+ addr = BANK(denali->flash_bank) | denali->page;
+ cmd = MODE_10 | addr;
+ index_addr(denali, cmd, MAIN_ACCESS);
+ }
+}
+
+/* this function examines buffers to see if they contain data that
+ * indicate that the buffer is part of an erased region of flash.
+ */
+static bool is_erased(uint8_t *buf, int len)
+{
+ int i = 0;
+ for (i = 0; i < len; i++)
+ if (buf[i] != 0xFF)
+ return false;
+ return true;
+}
+
+/* programs the controller to either enable/disable DMA transfers */
+static void denali_enable_dma(struct denali_nand_info *denali, bool en)
+{
+ uint32_t reg_val = 0x0;
+
+ if (en)
+ reg_val = DMA_ENABLE__FLAG;
+
+ writel(reg_val, denali->flash_reg + DMA_ENABLE);
+ readl(denali->flash_reg + DMA_ENABLE);
+}
+
+/* setups the HW to perform the data DMA */
+static void denali_setup_dma(struct denali_nand_info *denali, int op)
+{
+ uint32_t mode;
+ const int page_count = 1;
+ uint32_t addr = (uint32_t)denali->buf.dma_buf;
+
+ flush_dcache_range(addr, addr + sizeof(denali->buf.dma_buf));
+
+/* For Denali controller that is 64 bit bus IP core */
+#ifdef CONFIG_SYS_NAND_DENALI_64BIT
+ mode = MODE_10 | BANK(denali->flash_bank) | denali->page;
+
+ /* DMA is a three step process */
+
+ /* 1. setup transfer type, interrupt when complete,
+ burst len = 64 bytes, the number of pages */
+ index_addr(denali, mode, 0x01002000 | (64 << 16) | op | page_count);
+
+ /* 2. set memory low address bits 31:0 */
+ index_addr(denali, mode, addr);
+
+ /* 3. set memory high address bits 64:32 */
+ index_addr(denali, mode, 0);
+#else
+ mode = MODE_10 | BANK(denali->flash_bank);
+
+ /* DMA is a four step process */
+
+ /* 1. setup transfer type and # of pages */
+ index_addr(denali, mode | denali->page, 0x2000 | op | page_count);
+
+ /* 2. set memory high address bits 23:8 */
+ index_addr(denali, mode | ((uint32_t)(addr >> 16) << 8), 0x2200);
+
+ /* 3. set memory low address bits 23:8 */
+ index_addr(denali, mode | ((uint32_t)addr << 8), 0x2300);
+
+ /* 4. interrupt when complete, burst len = 64 bytes*/
+ index_addr(denali, mode | 0x14000, 0x2400);
+#endif
+}
+
+/* Common DMA function */
+static uint32_t denali_dma_configuration(struct denali_nand_info *denali,
+ uint32_t ops, bool raw_xfer,
+ uint32_t irq_mask, int oob_required)
+{
+ uint32_t irq_status = 0;
+ /* setup_ecc_for_xfer(bool ecc_en, bool transfer_spare) */
+ setup_ecc_for_xfer(denali, !raw_xfer, oob_required);
+
+ /* clear any previous interrupt flags */
+ clear_interrupts(denali);
+
+ /* enable the DMA */
+ denali_enable_dma(denali, true);
+
+ /* setup the DMA */
+ denali_setup_dma(denali, ops);
+
+ /* wait for operation to complete */
+ irq_status = wait_for_irq(denali, irq_mask);
+
+ /* if ECC fault happen, seems we need delay before turning off DMA.
+ * If not, the controller will go into non responsive condition */
+ if (irq_status & INTR_STATUS__ECC_UNCOR_ERR)
+ udelay(100);
+
+ /* disable the DMA */
+ denali_enable_dma(denali, false);
+
+ return irq_status;
+}
+
+static int write_page(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, bool raw_xfer, int oob_required)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+
+ uint32_t irq_status = 0;
+ uint32_t irq_mask = INTR_STATUS__DMA_CMD_COMP;
+
+ denali->status = 0;
+
+ /* copy buffer into DMA buffer */
+ memcpy(denali->buf.dma_buf, buf, mtd->writesize);
+
+ /* need extra memcpy for raw transfer */
+ if (raw_xfer)
+ memcpy(denali->buf.dma_buf + mtd->writesize,
+ chip->oob_poi, mtd->oobsize);
+
+ /* setting up DMA */
+ irq_status = denali_dma_configuration(denali, DENALI_WRITE, raw_xfer,
+ irq_mask, oob_required);
+
+ /* if timeout happen, error out */
+ if (!(irq_status & INTR_STATUS__DMA_CMD_COMP)) {
+ debug("DMA timeout for denali write_page\n");
+ denali->status = NAND_STATUS_FAIL;
+ return -EIO;
+ }
+
+ if (irq_status & INTR_STATUS__LOCKED_BLK) {
+ debug("Failed as write to locked block\n");
+ denali->status = NAND_STATUS_FAIL;
+ return -EIO;
+ }
+ return 0;
+}
+
+/* NAND core entry points */
+
+/*
+ * this is the callback that the NAND core calls to write a page. Since
+ * writing a page with ECC or without is similar, all the work is done
+ * by write_page above.
+ */
+static int denali_write_page(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, int oob_required)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+
+ /*
+ * for regular page writes, we let HW handle all the ECC
+ * data written to the device.
+ */
+ if (oob_required)
+ /* switch to main + spare access */
+ denali_mode_main_spare_access(denali);
+ else
+ /* switch to main access only */
+ denali_mode_main_access(denali);
+
+ return write_page(mtd, chip, buf, false, oob_required);
+}
+
+/*
+ * This is the callback that the NAND core calls to write a page without ECC.
+ * raw access is similar to ECC page writes, so all the work is done in the
+ * write_page() function above.
+ */
+static int denali_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, int oob_required)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+
+ /*
+ * for raw page writes, we want to disable ECC and simply write
+ * whatever data is in the buffer.
+ */
+
+ if (oob_required)
+ /* switch to main + spare access */
+ denali_mode_main_spare_access(denali);
+ else
+ /* switch to main access only */
+ denali_mode_main_access(denali);
+
+ return write_page(mtd, chip, buf, true, oob_required);
+}
+
+static int denali_write_oob(struct mtd_info *mtd, struct nand_chip *chip,
+ int page)
+{
+ return write_oob_data(mtd, chip->oob_poi, page);
+}
+
+/* raw include ECC value and all the spare area */
+static int denali_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+
+ uint32_t irq_status, irq_mask = INTR_STATUS__DMA_CMD_COMP;
+
+ if (denali->page != page) {
+ debug("Missing NAND_CMD_READ0 command\n");
+ return -EIO;
+ }
+
+ if (oob_required)
+ /* switch to main + spare access */
+ denali_mode_main_spare_access(denali);
+ else
+ /* switch to main access only */
+ denali_mode_main_access(denali);
+
+ /* setting up the DMA where ecc_enable is false */
+ irq_status = denali_dma_configuration(denali, DENALI_READ, true,
+ irq_mask, oob_required);
+
+ /* if timeout happen, error out */
+ if (!(irq_status & INTR_STATUS__DMA_CMD_COMP)) {
+ debug("DMA timeout for denali_read_page_raw\n");
+ return -EIO;
+ }
+
+ /* splitting the content to destination buffer holder */
+ memcpy(chip->oob_poi, (denali->buf.dma_buf + mtd->writesize),
+ mtd->oobsize);
+ memcpy(buf, denali->buf.dma_buf, mtd->writesize);
+
+ return 0;
+}
+
+static int denali_read_page(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint32_t irq_status, irq_mask = INTR_STATUS__DMA_CMD_COMP;
+
+ if (denali->page != page) {
+ debug("Missing NAND_CMD_READ0 command\n");
+ return -EIO;
+ }
+
+ if (oob_required)
+ /* switch to main + spare access */
+ denali_mode_main_spare_access(denali);
+ else
+ /* switch to main access only */
+ denali_mode_main_access(denali);
+
+ /* setting up the DMA where ecc_enable is true */
+ irq_status = denali_dma_configuration(denali, DENALI_READ, false,
+ irq_mask, oob_required);
+
+ memcpy(buf, denali->buf.dma_buf, mtd->writesize);
+
+ /* check whether any ECC error */
+ if (irq_status & INTR_STATUS__ECC_UNCOR_ERR) {
+ /* is the ECC cause by erase page, check using read_page_raw */
+ debug(" Uncorrected ECC detected\n");
+ denali_read_page_raw(mtd, chip, buf, oob_required,
+ denali->page);
+
+ if (is_erased(buf, mtd->writesize) == true &&
+ is_erased(chip->oob_poi, mtd->oobsize) == true) {
+ debug(" ECC error cause by erased block\n");
+ /* false alarm, return the 0xFF */
+ } else {
+ return -EIO;
+ }
+ }
+ memcpy(buf, denali->buf.dma_buf, mtd->writesize);
+ return 0;
+}
+
+static int denali_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+ int page)
+{
+ read_oob_data(mtd, chip->oob_poi, page);
+
+ return 0;
+}
+
+static uint8_t denali_read_byte(struct mtd_info *mtd)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint32_t addr, result;
+
+ addr = (uint32_t)MODE_11 | BANK(denali->flash_bank);
+ index_addr_read_data(denali, addr | 2, &result);
+ return (uint8_t)result & 0xFF;
+}
+
+static void denali_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint32_t i, addr, result;
+
+ /* delay for tR (data transfer from Flash array to data register) */
+ udelay(25);
+
+ /* ensure device completed else additional delay and polling */
+ wait_for_irq(denali, INTR_STATUS__INT_ACT);
+
+ addr = (uint32_t)MODE_11 | BANK(denali->flash_bank);
+ for (i = 0; i < len; i++) {
+ index_addr_read_data(denali, (uint32_t)addr | 2, &result);
+ write_byte_to_buf(denali, result);
+ }
+ memcpy(buf, denali->buf.buf, len);
+}
+
+static void denali_select_chip(struct mtd_info *mtd, int chip)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+
+ denali->flash_bank = chip;
+}
+
+static int denali_waitfunc(struct mtd_info *mtd, struct nand_chip *chip)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ int status = denali->status;
+ denali->status = 0;
+
+ return status;
+}
+
+static void denali_erase(struct mtd_info *mtd, int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint32_t cmd, irq_status;
+
+ /* clear interrupts */
+ clear_interrupts(denali);
+
+ /* setup page read request for access type */
+ cmd = MODE_10 | BANK(denali->flash_bank) | page;
+ index_addr(denali, cmd, 0x1);
+
+ /* wait for erase to complete or failure to occur */
+ irq_status = wait_for_irq(denali, INTR_STATUS__ERASE_COMP |
+ INTR_STATUS__ERASE_FAIL);
+
+ if (irq_status & INTR_STATUS__ERASE_FAIL ||
+ irq_status & INTR_STATUS__LOCKED_BLK)
+ denali->status = NAND_STATUS_FAIL;
+ else
+ denali->status = 0;
+}
+
+static void denali_cmdfunc(struct mtd_info *mtd, unsigned int cmd, int col,
+ int page)
+{
+ struct denali_nand_info *denali = mtd_to_denali(mtd);
+ uint32_t addr;
+
+ switch (cmd) {
+ case NAND_CMD_PAGEPROG:
+ break;
+ case NAND_CMD_STATUS:
+ addr = MODE_11 | BANK(denali->flash_bank);
+ index_addr(denali, addr | 0, cmd);
+ break;
+ case NAND_CMD_PARAM:
+ clear_interrupts(denali);
+ case NAND_CMD_READID:
+ reset_buf(denali);
+ /* sometimes ManufactureId read from register is not right
+ * e.g. some of Micron MT29F32G08QAA MLC NAND chips
+ * So here we send READID cmd to NAND insteand
+ * */
+ addr = MODE_11 | BANK(denali->flash_bank);
+ index_addr(denali, addr | 0, cmd);
+ index_addr(denali, addr | 1, col & 0xFF);
+ break;
+ case NAND_CMD_READ0:
+ case NAND_CMD_SEQIN:
+ denali->page = page;
+ break;
+ case NAND_CMD_RESET:
+ reset_bank(denali);
+ break;
+ case NAND_CMD_READOOB:
+ /* TODO: Read OOB data */
+ break;
+ case NAND_CMD_ERASE1:
+ /*
+ * supporting block erase only, not multiblock erase as
+ * it will cross plane and software need complex calculation
+ * to identify the block count for the cross plane
+ */
+ denali_erase(mtd, page);
+ break;
+ case NAND_CMD_ERASE2:
+ /* nothing to do here as it was done during NAND_CMD_ERASE1 */
+ break;
+ case NAND_CMD_UNLOCK1:
+ addr = MODE_10 | BANK(denali->flash_bank) | page;
+ index_addr(denali, addr | 0, DENALI_UNLOCK_START);
+ break;
+ case NAND_CMD_UNLOCK2:
+ addr = MODE_10 | BANK(denali->flash_bank) | page;
+ index_addr(denali, addr | 0, DENALI_UNLOCK_END);
+ break;
+ case NAND_CMD_LOCK:
+ addr = MODE_10 | BANK(denali->flash_bank);
+ index_addr(denali, addr | 0, DENALI_LOCK);
+ break;
+ default:
+ printf(": unsupported command received 0x%x\n", cmd);
+ break;
+ }
+}
+/* end NAND core entry points */
+
+/* Initialization code to bring the device up to a known good state */
+static void denali_hw_init(struct denali_nand_info *denali)
+{
+ /*
+ * tell driver how many bit controller will skip before writing
+ * ECC code in OOB. This is normally used for bad block marker
+ */
+ writel(CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES,
+ denali->flash_reg + SPARE_AREA_SKIP_BYTES);
+ detect_max_banks(denali);
+ denali_nand_reset(denali);
+ writel(0x0F, denali->flash_reg + RB_PIN_ENABLED);
+ writel(CHIP_EN_DONT_CARE__FLAG,
+ denali->flash_reg + CHIP_ENABLE_DONT_CARE);
+ writel(0xffff, denali->flash_reg + SPARE_AREA_MARKER);
+
+ /* Should set value for these registers when init */
+ writel(0, denali->flash_reg + TWO_ROW_ADDR_CYCLES);
+ writel(1, denali->flash_reg + ECC_ENABLE);
+ denali_nand_timing_set(denali);
+ denali_irq_init(denali);
+}
+
+static struct nand_ecclayout nand_oob;
+
+static int denali_nand_init(struct nand_chip *nand)
+{
+ struct denali_nand_info *denali;
+
+ denali = malloc(sizeof(*denali));
+ if (!denali)
+ return -ENOMEM;
+
+ nand->priv = denali;
+
+ denali->flash_reg = (void __iomem *)CONFIG_SYS_NAND_REGS_BASE;
+ denali->flash_mem = (void __iomem *)CONFIG_SYS_NAND_DATA_BASE;
+
+#ifdef CONFIG_SYS_NAND_USE_FLASH_BBT
+ /* check whether flash got BBT table (located at end of flash). As we
+ * use NAND_BBT_NO_OOB, the BBT page will start with
+ * bbt_pattern. We will have mirror pattern too */
+ nand->bbt_options |= NAND_BBT_USE_FLASH;
+ /*
+ * We are using main + spare with ECC support. As BBT need ECC support,
+ * we need to ensure BBT code don't write to OOB for the BBT pattern.
+ * All BBT info will be stored into data area with ECC support.
+ */
+ nand->bbt_options |= NAND_BBT_NO_OOB;
+#endif
+
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.size = CONFIG_NAND_DENALI_ECC_SIZE;
+ nand->ecc.read_oob = denali_read_oob;
+ nand->ecc.write_oob = denali_write_oob;
+ nand->ecc.read_page = denali_read_page;
+ nand->ecc.read_page_raw = denali_read_page_raw;
+ nand->ecc.write_page = denali_write_page;
+ nand->ecc.write_page_raw = denali_write_page_raw;
+ /*
+ * Tell driver the ecc strength. This register may be already set
+ * correctly. So we read this value out.
+ */
+ nand->ecc.strength = readl(denali->flash_reg + ECC_CORRECTION);
+ switch (nand->ecc.size) {
+ case 512:
+ nand->ecc.bytes = (nand->ecc.strength * 13 + 15) / 16 * 2;
+ break;
+ case 1024:
+ nand->ecc.bytes = (nand->ecc.strength * 14 + 15) / 16 * 2;
+ break;
+ default:
+ pr_err("Unsupported ECC size\n");
+ return -EINVAL;
+ }
+ nand_oob.eccbytes = nand->ecc.bytes;
+ nand->ecc.layout = &nand_oob;
+
+ /* Set address of hardware control function */
+ nand->cmdfunc = denali_cmdfunc;
+ nand->read_byte = denali_read_byte;
+ nand->read_buf = denali_read_buf;
+ nand->select_chip = denali_select_chip;
+ nand->waitfunc = denali_waitfunc;
+ denali_hw_init(denali);
+ return 0;
+}
+
+int board_nand_init(struct nand_chip *chip)
+{
+ return denali_nand_init(chip);
+}
--- /dev/null
+/*
+ * Copyright (C) 2013-2014 Altera Corporation <www.altera.com>
+ * Copyright (C) 2009-2010, Intel Corporation and its suppliers.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <linux/mtd/nand.h>
+
+#define DEVICE_RESET 0x0
+#define DEVICE_RESET__BANK0 0x0001
+#define DEVICE_RESET__BANK1 0x0002
+#define DEVICE_RESET__BANK2 0x0004
+#define DEVICE_RESET__BANK3 0x0008
+
+#define TRANSFER_SPARE_REG 0x10
+#define TRANSFER_SPARE_REG__FLAG 0x0001
+
+#define LOAD_WAIT_CNT 0x20
+#define LOAD_WAIT_CNT__VALUE 0xffff
+
+#define PROGRAM_WAIT_CNT 0x30
+#define PROGRAM_WAIT_CNT__VALUE 0xffff
+
+#define ERASE_WAIT_CNT 0x40
+#define ERASE_WAIT_CNT__VALUE 0xffff
+
+#define INT_MON_CYCCNT 0x50
+#define INT_MON_CYCCNT__VALUE 0xffff
+
+#define RB_PIN_ENABLED 0x60
+#define RB_PIN_ENABLED__BANK0 0x0001
+#define RB_PIN_ENABLED__BANK1 0x0002
+#define RB_PIN_ENABLED__BANK2 0x0004
+#define RB_PIN_ENABLED__BANK3 0x0008
+
+#define MULTIPLANE_OPERATION 0x70
+#define MULTIPLANE_OPERATION__FLAG 0x0001
+
+#define MULTIPLANE_READ_ENABLE 0x80
+#define MULTIPLANE_READ_ENABLE__FLAG 0x0001
+
+#define COPYBACK_DISABLE 0x90
+#define COPYBACK_DISABLE__FLAG 0x0001
+
+#define CACHE_WRITE_ENABLE 0xa0
+#define CACHE_WRITE_ENABLE__FLAG 0x0001
+
+#define CACHE_READ_ENABLE 0xb0
+#define CACHE_READ_ENABLE__FLAG 0x0001
+
+#define PREFETCH_MODE 0xc0
+#define PREFETCH_MODE__PREFETCH_EN 0x0001
+#define PREFETCH_MODE__PREFETCH_BURST_LENGTH 0xfff0
+
+#define CHIP_ENABLE_DONT_CARE 0xd0
+#define CHIP_EN_DONT_CARE__FLAG 0x01
+
+#define ECC_ENABLE 0xe0
+#define ECC_ENABLE__FLAG 0x0001
+
+#define GLOBAL_INT_ENABLE 0xf0
+#define GLOBAL_INT_EN_FLAG 0x01
+
+#define WE_2_RE 0x100
+#define WE_2_RE__VALUE 0x003f
+
+#define ADDR_2_DATA 0x110
+#define ADDR_2_DATA__VALUE 0x003f
+
+#define RE_2_WE 0x120
+#define RE_2_WE__VALUE 0x003f
+
+#define ACC_CLKS 0x130
+#define ACC_CLKS__VALUE 0x000f
+
+#define NUMBER_OF_PLANES 0x140
+#define NUMBER_OF_PLANES__VALUE 0x0007
+
+#define PAGES_PER_BLOCK 0x150
+#define PAGES_PER_BLOCK__VALUE 0xffff
+
+#define DEVICE_WIDTH 0x160
+#define DEVICE_WIDTH__VALUE 0x0003
+
+#define DEVICE_MAIN_AREA_SIZE 0x170
+#define DEVICE_MAIN_AREA_SIZE__VALUE 0xffff
+
+#define DEVICE_SPARE_AREA_SIZE 0x180
+#define DEVICE_SPARE_AREA_SIZE__VALUE 0xffff
+
+#define TWO_ROW_ADDR_CYCLES 0x190
+#define TWO_ROW_ADDR_CYCLES__FLAG 0x0001
+
+#define MULTIPLANE_ADDR_RESTRICT 0x1a0
+#define MULTIPLANE_ADDR_RESTRICT__FLAG 0x0001
+
+#define ECC_CORRECTION 0x1b0
+#define ECC_CORRECTION__VALUE 0x001f
+
+#define READ_MODE 0x1c0
+#define READ_MODE__VALUE 0x000f
+
+#define WRITE_MODE 0x1d0
+#define WRITE_MODE__VALUE 0x000f
+
+#define COPYBACK_MODE 0x1e0
+#define COPYBACK_MODE__VALUE 0x000f
+
+#define RDWR_EN_LO_CNT 0x1f0
+#define RDWR_EN_LO_CNT__VALUE 0x001f
+
+#define RDWR_EN_HI_CNT 0x200
+#define RDWR_EN_HI_CNT__VALUE 0x001f
+
+#define MAX_RD_DELAY 0x210
+#define MAX_RD_DELAY__VALUE 0x000f
+
+#define CS_SETUP_CNT 0x220
+#define CS_SETUP_CNT__VALUE 0x001f
+
+#define SPARE_AREA_SKIP_BYTES 0x230
+#define SPARE_AREA_SKIP_BYTES__VALUE 0x003f
+
+#define SPARE_AREA_MARKER 0x240
+#define SPARE_AREA_MARKER__VALUE 0xffff
+
+#define DEVICES_CONNECTED 0x250
+#define DEVICES_CONNECTED__VALUE 0x0007
+
+#define DIE_MASK 0x260
+#define DIE_MASK__VALUE 0x00ff
+
+#define FIRST_BLOCK_OF_NEXT_PLANE 0x270
+#define FIRST_BLOCK_OF_NEXT_PLANE__VALUE 0xffff
+
+#define WRITE_PROTECT 0x280
+#define WRITE_PROTECT__FLAG 0x0001
+
+#define RE_2_RE 0x290
+#define RE_2_RE__VALUE 0x003f
+
+#define MANUFACTURER_ID 0x300
+#define MANUFACTURER_ID__VALUE 0x00ff
+
+#define DEVICE_ID 0x310
+#define DEVICE_ID__VALUE 0x00ff
+
+#define DEVICE_PARAM_0 0x320
+#define DEVICE_PARAM_0__VALUE 0x00ff
+
+#define DEVICE_PARAM_1 0x330
+#define DEVICE_PARAM_1__VALUE 0x00ff
+
+#define DEVICE_PARAM_2 0x340
+#define DEVICE_PARAM_2__VALUE 0x00ff
+
+#define LOGICAL_PAGE_DATA_SIZE 0x350
+#define LOGICAL_PAGE_DATA_SIZE__VALUE 0xffff
+
+#define LOGICAL_PAGE_SPARE_SIZE 0x360
+#define LOGICAL_PAGE_SPARE_SIZE__VALUE 0xffff
+
+#define REVISION 0x370
+#define REVISION__VALUE 0xffff
+
+#define ONFI_DEVICE_FEATURES 0x380
+#define ONFI_DEVICE_FEATURES__VALUE 0x003f
+
+#define ONFI_OPTIONAL_COMMANDS 0x390
+#define ONFI_OPTIONAL_COMMANDS__VALUE 0x003f
+
+#define ONFI_TIMING_MODE 0x3a0
+#define ONFI_TIMING_MODE__VALUE 0x003f
+
+#define ONFI_PGM_CACHE_TIMING_MODE 0x3b0
+#define ONFI_PGM_CACHE_TIMING_MODE__VALUE 0x003f
+
+#define ONFI_DEVICE_NO_OF_LUNS 0x3c0
+#define ONFI_DEVICE_NO_OF_LUNS__NO_OF_LUNS 0x00ff
+#define ONFI_DEVICE_NO_OF_LUNS__ONFI_DEVICE 0x0100
+
+#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_L 0x3d0
+#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_L__VALUE 0xffff
+
+#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_U 0x3e0
+#define ONFI_DEVICE_NO_OF_BLOCKS_PER_LUN_U__VALUE 0xffff
+
+#define FEATURES 0x3f0
+#define FEATURES__N_BANKS 0x0003
+#define FEATURES__ECC_MAX_ERR 0x003c
+#define FEATURES__DMA 0x0040
+#define FEATURES__CMD_DMA 0x0080
+#define FEATURES__PARTITION 0x0100
+#define FEATURES__XDMA_SIDEBAND 0x0200
+#define FEATURES__GPREG 0x0400
+#define FEATURES__INDEX_ADDR 0x0800
+
+#define TRANSFER_MODE 0x400
+#define TRANSFER_MODE__VALUE 0x0003
+
+#define INTR_STATUS(__bank) (0x410 + ((__bank) * 0x50))
+#define INTR_EN(__bank) (0x420 + ((__bank) * 0x50))
+
+/*
+ * Some versions of the IP have the ECC fixup handled in hardware. In this
+ * configuration we only get interrupted when the error is uncorrectable.
+ * Unfortunately this bit replaces INTR_STATUS__ECC_TRANSACTION_DONE from the
+ * old IP.
+ */
+#define INTR_STATUS__ECC_UNCOR_ERR 0x0001
+#define INTR_STATUS__ECC_TRANSACTION_DONE 0x0001
+#define INTR_STATUS__ECC_ERR 0x0002
+#define INTR_STATUS__DMA_CMD_COMP 0x0004
+#define INTR_STATUS__TIME_OUT 0x0008
+#define INTR_STATUS__PROGRAM_FAIL 0x0010
+#define INTR_STATUS__ERASE_FAIL 0x0020
+#define INTR_STATUS__LOAD_COMP 0x0040
+#define INTR_STATUS__PROGRAM_COMP 0x0080
+#define INTR_STATUS__ERASE_COMP 0x0100
+#define INTR_STATUS__PIPE_CPYBCK_CMD_COMP 0x0200
+#define INTR_STATUS__LOCKED_BLK 0x0400
+#define INTR_STATUS__UNSUP_CMD 0x0800
+#define INTR_STATUS__INT_ACT 0x1000
+#define INTR_STATUS__RST_COMP 0x2000
+#define INTR_STATUS__PIPE_CMD_ERR 0x4000
+#define INTR_STATUS__PAGE_XFER_INC 0x8000
+
+#define INTR_EN__ECC_TRANSACTION_DONE 0x0001
+#define INTR_EN__ECC_ERR 0x0002
+#define INTR_EN__DMA_CMD_COMP 0x0004
+#define INTR_EN__TIME_OUT 0x0008
+#define INTR_EN__PROGRAM_FAIL 0x0010
+#define INTR_EN__ERASE_FAIL 0x0020
+#define INTR_EN__LOAD_COMP 0x0040
+#define INTR_EN__PROGRAM_COMP 0x0080
+#define INTR_EN__ERASE_COMP 0x0100
+#define INTR_EN__PIPE_CPYBCK_CMD_COMP 0x0200
+#define INTR_EN__LOCKED_BLK 0x0400
+#define INTR_EN__UNSUP_CMD 0x0800
+#define INTR_EN__INT_ACT 0x1000
+#define INTR_EN__RST_COMP 0x2000
+#define INTR_EN__PIPE_CMD_ERR 0x4000
+#define INTR_EN__PAGE_XFER_INC 0x8000
+
+#define PAGE_CNT(__bank) (0x430 + ((__bank) * 0x50))
+#define ERR_PAGE_ADDR(__bank) (0x440 + ((__bank) * 0x50))
+#define ERR_BLOCK_ADDR(__bank) (0x450 + ((__bank) * 0x50))
+
+#define DATA_INTR 0x550
+#define DATA_INTR__WRITE_SPACE_AV 0x0001
+#define DATA_INTR__READ_DATA_AV 0x0002
+
+#define DATA_INTR_EN 0x560
+#define DATA_INTR_EN__WRITE_SPACE_AV 0x0001
+#define DATA_INTR_EN__READ_DATA_AV 0x0002
+
+#define GPREG_0 0x570
+#define GPREG_0__VALUE 0xffff
+
+#define GPREG_1 0x580
+#define GPREG_1__VALUE 0xffff
+
+#define GPREG_2 0x590
+#define GPREG_2__VALUE 0xffff
+
+#define GPREG_3 0x5a0
+#define GPREG_3__VALUE 0xffff
+
+#define ECC_THRESHOLD 0x600
+#define ECC_THRESHOLD__VALUE 0x03ff
+
+#define ECC_ERROR_BLOCK_ADDRESS 0x610
+#define ECC_ERROR_BLOCK_ADDRESS__VALUE 0xffff
+
+#define ECC_ERROR_PAGE_ADDRESS 0x620
+#define ECC_ERROR_PAGE_ADDRESS__VALUE 0x0fff
+#define ECC_ERROR_PAGE_ADDRESS__BANK 0xf000
+
+#define ECC_ERROR_ADDRESS 0x630
+#define ECC_ERROR_ADDRESS__OFFSET 0x0fff
+#define ECC_ERROR_ADDRESS__SECTOR_NR 0xf000
+
+#define ERR_CORRECTION_INFO 0x640
+#define ERR_CORRECTION_INFO__BYTEMASK 0x00ff
+#define ERR_CORRECTION_INFO__DEVICE_NR 0x0f00
+#define ERR_CORRECTION_INFO__ERROR_TYPE 0x4000
+#define ERR_CORRECTION_INFO__LAST_ERR_INFO 0x8000
+
+#define DMA_ENABLE 0x700
+#define DMA_ENABLE__FLAG 0x0001
+
+#define IGNORE_ECC_DONE 0x710
+#define IGNORE_ECC_DONE__FLAG 0x0001
+
+#define DMA_INTR 0x720
+#define DMA_INTR__TARGET_ERROR 0x0001
+#define DMA_INTR__DESC_COMP_CHANNEL0 0x0002
+#define DMA_INTR__DESC_COMP_CHANNEL1 0x0004
+#define DMA_INTR__DESC_COMP_CHANNEL2 0x0008
+#define DMA_INTR__DESC_COMP_CHANNEL3 0x0010
+#define DMA_INTR__MEMCOPY_DESC_COMP 0x0020
+
+#define DMA_INTR_EN 0x730
+#define DMA_INTR_EN__TARGET_ERROR 0x0001
+#define DMA_INTR_EN__DESC_COMP_CHANNEL0 0x0002
+#define DMA_INTR_EN__DESC_COMP_CHANNEL1 0x0004
+#define DMA_INTR_EN__DESC_COMP_CHANNEL2 0x0008
+#define DMA_INTR_EN__DESC_COMP_CHANNEL3 0x0010
+#define DMA_INTR_EN__MEMCOPY_DESC_COMP 0x0020
+
+#define TARGET_ERR_ADDR_LO 0x740
+#define TARGET_ERR_ADDR_LO__VALUE 0xffff
+
+#define TARGET_ERR_ADDR_HI 0x750
+#define TARGET_ERR_ADDR_HI__VALUE 0xffff
+
+#define CHNL_ACTIVE 0x760
+#define CHNL_ACTIVE__CHANNEL0 0x0001
+#define CHNL_ACTIVE__CHANNEL1 0x0002
+#define CHNL_ACTIVE__CHANNEL2 0x0004
+#define CHNL_ACTIVE__CHANNEL3 0x0008
+
+#define ACTIVE_SRC_ID 0x800
+#define ACTIVE_SRC_ID__VALUE 0x00ff
+
+#define PTN_INTR 0x810
+#define PTN_INTR__CONFIG_ERROR 0x0001
+#define PTN_INTR__ACCESS_ERROR_BANK0 0x0002
+#define PTN_INTR__ACCESS_ERROR_BANK1 0x0004
+#define PTN_INTR__ACCESS_ERROR_BANK2 0x0008
+#define PTN_INTR__ACCESS_ERROR_BANK3 0x0010
+#define PTN_INTR__REG_ACCESS_ERROR 0x0020
+
+#define PTN_INTR_EN 0x820
+#define PTN_INTR_EN__CONFIG_ERROR 0x0001
+#define PTN_INTR_EN__ACCESS_ERROR_BANK0 0x0002
+#define PTN_INTR_EN__ACCESS_ERROR_BANK1 0x0004
+#define PTN_INTR_EN__ACCESS_ERROR_BANK2 0x0008
+#define PTN_INTR_EN__ACCESS_ERROR_BANK3 0x0010
+#define PTN_INTR_EN__REG_ACCESS_ERROR 0x0020
+
+#define PERM_SRC_ID(__bank) (0x830 + ((__bank) * 0x40))
+#define PERM_SRC_ID__SRCID 0x00ff
+#define PERM_SRC_ID__DIRECT_ACCESS_ACTIVE 0x0800
+#define PERM_SRC_ID__WRITE_ACTIVE 0x2000
+#define PERM_SRC_ID__READ_ACTIVE 0x4000
+#define PERM_SRC_ID__PARTITION_VALID 0x8000
+
+#define MIN_BLK_ADDR(__bank) (0x840 + ((__bank) * 0x40))
+#define MIN_BLK_ADDR__VALUE 0xffff
+
+#define MAX_BLK_ADDR(__bank) (0x850 + ((__bank) * 0x40))
+#define MAX_BLK_ADDR__VALUE 0xffff
+
+#define MIN_MAX_BANK(__bank) (0x860 + ((__bank) * 0x40))
+#define MIN_MAX_BANK__MIN_VALUE 0x0003
+#define MIN_MAX_BANK__MAX_VALUE 0x000c
+
+/* lld.h */
+#define GOOD_BLOCK 0
+#define DEFECTIVE_BLOCK 1
+#define READ_ERROR 2
+
+#define CLK_X 5
+#define CLK_MULTI 4
+
+/* spectraswconfig.h */
+#define CMD_DMA 0
+
+#define SPECTRA_PARTITION_ID 0
+/**** Block Table and Reserved Block Parameters *****/
+#define SPECTRA_START_BLOCK 3
+#define NUM_FREE_BLOCKS_GATE 30
+
+/* KBV - Updated to LNW scratch register address */
+#define SCRATCH_REG_ADDR CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR
+#define SCRATCH_REG_SIZE 64
+
+#define GLOB_HWCTL_DEFAULT_BLKS 2048
+
+#define CUSTOM_CONF_PARAMS 0
+
+#ifndef _LLD_NAND_
+#define _LLD_NAND_
+
+#define INDEX_CTRL_REG 0x0
+#define INDEX_DATA_REG 0x10
+
+#define MODE_00 0x00000000
+#define MODE_01 0x04000000
+#define MODE_10 0x08000000
+#define MODE_11 0x0C000000
+
+
+#define DATA_TRANSFER_MODE 0
+#define PROTECTION_PER_BLOCK 1
+#define LOAD_WAIT_COUNT 2
+#define PROGRAM_WAIT_COUNT 3
+#define ERASE_WAIT_COUNT 4
+#define INT_MONITOR_CYCLE_COUNT 5
+#define READ_BUSY_PIN_ENABLED 6
+#define MULTIPLANE_OPERATION_SUPPORT 7
+#define PRE_FETCH_MODE 8
+#define CE_DONT_CARE_SUPPORT 9
+#define COPYBACK_SUPPORT 10
+#define CACHE_WRITE_SUPPORT 11
+#define CACHE_READ_SUPPORT 12
+#define NUM_PAGES_IN_BLOCK 13
+#define ECC_ENABLE_SELECT 14
+#define WRITE_ENABLE_2_READ_ENABLE 15
+#define ADDRESS_2_DATA 16
+#define READ_ENABLE_2_WRITE_ENABLE 17
+#define TWO_ROW_ADDRESS_CYCLES 18
+#define MULTIPLANE_ADDRESS_RESTRICT 19
+#define ACC_CLOCKS 20
+#define READ_WRITE_ENABLE_LOW_COUNT 21
+#define READ_WRITE_ENABLE_HIGH_COUNT 22
+
+#define ECC_SECTOR_SIZE 512
+
+#define DENALI_BUF_SIZE (NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE)
+
+struct nand_buf {
+ int head;
+ int tail;
+ /* seprating dma_buf as buf can be used for status read purpose */
+ uint8_t dma_buf[DENALI_BUF_SIZE] __aligned(64);
+ uint8_t buf[DENALI_BUF_SIZE];
+};
+
+#define INTEL_CE4100 1
+#define INTEL_MRST 2
+#define DT 3
+
+struct denali_nand_info {
+ struct mtd_info mtd;
+ struct nand_chip *nand;
+
+ int flash_bank; /* currently selected chip */
+ int status;
+ int platform;
+ struct nand_buf buf;
+ struct device *dev;
+ int total_used_banks;
+ uint32_t block; /* stored for future use */
+ uint32_t page;
+ void __iomem *flash_reg; /* Mapped io reg base address */
+ void __iomem *flash_mem; /* Mapped io reg base address */
+
+ /* elements used by ISR */
+ /*struct completion complete;*/
+
+ uint32_t irq_status;
+ int irq_debug_array[32];
+ int idx;
+ int irq;
+
+ uint32_t devnum; /* represent how many nands connected */
+ uint32_t fwblks; /* represent how many blocks FW used */
+ uint32_t totalblks;
+ uint32_t blksperchip;
+ uint32_t bbtskipbytes;
+ uint32_t max_banks;
+};
+
+#endif /*_LLD_NAND_*/
--- /dev/null
+/*
+ * Copyright (C) 2014 Panasonic Corporation
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/unaligned.h>
+#include <linux/mtd/nand.h>
+#include "denali.h"
+
+#define SPARE_ACCESS 0x41
+#define MAIN_ACCESS 0x42
+#define PIPELINE_ACCESS 0x2000
+
+#define BANK(x) ((x) << 24)
+
+static void __iomem *denali_flash_mem =
+ (void __iomem *)CONFIG_SYS_NAND_DATA_BASE;
+static void __iomem *denali_flash_reg =
+ (void __iomem *)CONFIG_SYS_NAND_REGS_BASE;
+
+static const int flash_bank;
+static uint8_t page_buffer[NAND_MAX_PAGESIZE];
+static int page_size, oob_size, pages_per_block;
+
+static void index_addr(uint32_t address, uint32_t data)
+{
+ writel(address, denali_flash_mem + INDEX_CTRL_REG);
+ writel(data, denali_flash_mem + INDEX_DATA_REG);
+}
+
+static int wait_for_irq(uint32_t irq_mask)
+{
+ unsigned long timeout = 1000000;
+ uint32_t intr_status;
+
+ do {
+ intr_status = readl(denali_flash_reg + INTR_STATUS(flash_bank));
+
+ if (intr_status & INTR_STATUS__ECC_UNCOR_ERR) {
+ debug("Uncorrected ECC detected\n");
+ return -EIO;
+ }
+
+ if (intr_status & irq_mask)
+ break;
+
+ udelay(1);
+ timeout--;
+ } while (timeout);
+
+ if (!timeout) {
+ debug("Timeout with interrupt status %08x\n", intr_status);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static void read_data_from_flash_mem(uint8_t *buf, int len)
+{
+ int i;
+ uint32_t *buf32;
+
+ /* transfer the data from the flash */
+ buf32 = (uint32_t *)buf;
+
+ /*
+ * Let's take care of unaligned access although it rarely happens.
+ * Avoid put_unaligned() for the normal use cases since it leads to
+ * a bit performance regression.
+ */
+ if ((unsigned long)buf32 % 4) {
+ for (i = 0; i < len / 4; i++)
+ put_unaligned(readl(denali_flash_mem + INDEX_DATA_REG),
+ buf32++);
+ } else {
+ for (i = 0; i < len / 4; i++)
+ *buf32++ = readl(denali_flash_mem + INDEX_DATA_REG);
+ }
+
+ if (len % 4) {
+ u32 tmp;
+
+ tmp = cpu_to_le32(readl(denali_flash_mem + INDEX_DATA_REG));
+ buf = (uint8_t *)buf32;
+ for (i = 0; i < len % 4; i++) {
+ *buf++ = tmp;
+ tmp >>= 8;
+ }
+ }
+}
+
+int denali_send_pipeline_cmd(int page, int ecc_en, int access_type)
+{
+ uint32_t addr, cmd;
+ static uint32_t page_count = 1;
+
+ writel(ecc_en, denali_flash_reg + ECC_ENABLE);
+
+ /* clear all bits of intr_status. */
+ writel(0xffff, denali_flash_reg + INTR_STATUS(flash_bank));
+
+ addr = BANK(flash_bank) | page;
+
+ /* setup the acccess type */
+ cmd = MODE_10 | addr;
+ index_addr(cmd, access_type);
+
+ /* setup the pipeline command */
+ index_addr(cmd, PIPELINE_ACCESS | page_count);
+
+ cmd = MODE_01 | addr;
+ writel(cmd, denali_flash_mem + INDEX_CTRL_REG);
+
+ return wait_for_irq(INTR_STATUS__LOAD_COMP);
+}
+
+static int nand_read_oob(void *buf, int page)
+{
+ int ret;
+
+ ret = denali_send_pipeline_cmd(page, 0, SPARE_ACCESS);
+ if (ret < 0)
+ return ret;
+
+ read_data_from_flash_mem(buf, oob_size);
+
+ return 0;
+}
+
+static int nand_read_page(void *buf, int page)
+{
+ int ret;
+
+ ret = denali_send_pipeline_cmd(page, 1, MAIN_ACCESS);
+ if (ret < 0)
+ return ret;
+
+ read_data_from_flash_mem(buf, page_size);
+
+ return 0;
+}
+
+static int nand_block_isbad(int block)
+{
+ int ret;
+
+ ret = nand_read_oob(page_buffer, block * pages_per_block);
+ if (ret < 0)
+ return ret;
+
+ return page_buffer[CONFIG_SYS_NAND_BAD_BLOCK_POS] != 0xff;
+}
+
+/* nand_init() - initialize data to make nand usable by SPL */
+void nand_init(void)
+{
+ /* access to main area */
+ writel(0, denali_flash_reg + TRANSFER_SPARE_REG);
+
+ /*
+ * These registers are expected to be already set by the hardware
+ * or earlier boot code. So we read these values out.
+ */
+ page_size = readl(denali_flash_reg + DEVICE_MAIN_AREA_SIZE);
+ oob_size = readl(denali_flash_reg + DEVICE_SPARE_AREA_SIZE);
+ pages_per_block = readl(denali_flash_reg + PAGES_PER_BLOCK);
+}
+
+int nand_spl_load_image(uint32_t offs, unsigned int size, void *dst)
+{
+ int block, page, column, readlen;
+ int ret;
+ int force_bad_block_check = 1;
+
+ page = offs / page_size;
+ column = offs % page_size;
+
+ block = page / pages_per_block;
+ page = page % pages_per_block;
+
+ while (size) {
+ if (force_bad_block_check || page == 0) {
+ ret = nand_block_isbad(block);
+ if (ret < 0)
+ return ret;
+
+ if (ret) {
+ block++;
+ continue;
+ }
+ }
+
+ force_bad_block_check = 0;
+
+ if (unlikely(column || size < page_size)) {
+ /* Partial page read */
+ ret = nand_read_page(page_buffer,
+ block * pages_per_block + page);
+ if (ret < 0)
+ return ret;
+
+ readlen = min(page_size - column, size);
+ memcpy(dst, page_buffer, readlen);
+
+ column = 0;
+ } else {
+ ret = nand_read_page(dst,
+ block * pages_per_block + page);
+ if (ret < 0)
+ return ret;
+
+ readlen = page_size;
+ }
+
+ size -= readlen;
+ dst += readlen;
+ page++;
+ if (page == pages_per_block) {
+ block++;
+ page = 0;
+ }
+ }
+
+ return 0;
+}
+
+void nand_deselect(void) {}
#define MAX_BANKS 8
#define ERR_BYTE 0xFF /* Value returned for read bytes when read failed */
-#define FCM_TIMEOUT_MSECS 10 /* Maximum number of mSecs to wait for FCM */
#define LTESR_NAND_MASK (LTESR_FCT | LTESR_PAR | LTESR_CC)
struct fsl_elbc_mtd *priv = chip->priv;
struct fsl_elbc_ctrl *ctrl = priv->ctrl;
fsl_lbc_t *lbc = ctrl->regs;
- long long end_tick;
+ u32 timeo = (CONFIG_SYS_HZ * 10) / 1000;
+ u32 time_start;
u32 ltesr;
/* Setup the FMR[OP] to execute without write protection */
out_be32(&lbc->lsor, priv->bank);
/* wait for FCM complete flag or timeout */
- end_tick = usec2ticks(FCM_TIMEOUT_MSECS * 1000) + get_ticks();
+ time_start = get_timer(0);
ltesr = 0;
- while (end_tick > get_ticks()) {
+ while (get_timer(time_start) < timeo) {
ltesr = in_be32(&lbc->ltesr);
if (ltesr & LTESR_CC)
break;
#define MAX_BANKS CONFIG_SYS_FSL_IFC_BANK_COUNT
#define ERR_BYTE 0xFF /* Value returned for read bytes
when read failed */
-#define IFC_TIMEOUT_MSECS 10 /* Maximum number of mSecs to wait for IFC
- NAND Machine */
struct fsl_ifc_ctrl;
struct fsl_ifc_mtd *priv = chip->priv;
struct fsl_ifc_ctrl *ctrl = priv->ctrl;
struct fsl_ifc *ifc = ctrl->regs;
- long long end_tick;
+ u32 timeo = (CONFIG_SYS_HZ * 10) / 1000;
+ u32 time_start;
u32 eccstat[4];
int i;
IFC_NAND_SEQ_STRT_FIR_STRT);
/* wait for NAND Machine complete flag or timeout */
- end_tick = usec2ticks(IFC_TIMEOUT_MSECS * 1000) + get_ticks();
+ time_start = get_timer(0);
- while (end_tick > get_ticks()) {
+ while (get_timer(time_start) < timeo) {
ctrl->status = ifc_in32(&ifc->ifc_nand.nand_evter_stat);
if (ctrl->status & IFC_NAND_EVTER_STAT_OPC)
struct fsl_ifc *ifc = ifc_ctrl->regs;
uint32_t cs = 0, csor = 0, csor_8k = 0, csor_ext = 0;
uint32_t ncfgr = 0;
- long long end_tick;
+ u32 timeo = (CONFIG_SYS_HZ * 10) / 1000;
+ u32 time_start;
if (ver > FSL_IFC_V1_1_0) {
ncfgr = ifc_in32(&ifc->ifc_nand.ncfgr);
ifc_out32(&ifc->ifc_nand.ncfgr, ncfgr | IFC_NAND_SRAM_INIT_EN);
/* wait for SRAM_INIT bit to be clear or timeout */
- end_tick = usec2ticks(IFC_TIMEOUT_MSECS * 1000) + get_ticks();
- while (end_tick > get_ticks()) {
+ time_start = get_timer(0);
+ while (get_timer(time_start) < timeo) {
ifc_ctrl->status =
ifc_in32(&ifc->ifc_nand.nand_evter_stat);
/* start read seq */
ifc_out32(&ifc->ifc_nand.nandseq_strt, IFC_NAND_SEQ_STRT_FIR_STRT);
- /* wait for NAND Machine complete flag or timeout */
- end_tick = usec2ticks(IFC_TIMEOUT_MSECS * 1000) + get_ticks();
+ time_start = get_timer(0);
- while (end_tick > get_ticks()) {
+ while (get_timer(time_start) < timeo) {
ifc_ctrl->status = ifc_in32(&ifc->ifc_nand.nand_evter_stat);
if (ifc_ctrl->status & IFC_NAND_EVTER_STAT_OPC)
{
int i;
u16 *p = (u16 *) buf;
- len >>= 1;
-
+
for (i = 0; i < len; i++)
p[i] = readw(addr);
}
{
int i;
u16 *p = (u16 *) buf;
- len >>= 1;
for (i = 0; i < len; i++)
writew(p[i], addr);
/* Assume all SPI flashes have 3 byte addresses since they do atm */
#define SF_ADDR_LEN 3
-struct sandbox_spi_flash_erase_commands {
- u8 cmd;
- u32 size;
-};
-#define IDCODE_LEN 5
-#define MAX_ERASE_CMDS 3
-struct sandbox_spi_flash_data {
- const char *name;
- u8 idcode[IDCODE_LEN];
- u32 size;
- const struct sandbox_spi_flash_erase_commands
- erase_cmds[MAX_ERASE_CMDS];
-};
-
-/* Structure describing all the flashes we know how to emulate */
-static const struct sandbox_spi_flash_data sandbox_sf_flashes[] = {
- {
- "M25P16", { 0x20, 0x20, 0x15 }, (2 << 20),
- { /* erase commands */
- { 0xd8, (64 << 10), }, /* sector */
- { 0xc7, (2 << 20), }, /* bulk */
- },
- },
- {
- "W25Q32", { 0xef, 0x40, 0x16 }, (4 << 20),
- { /* erase commands */
- { 0x20, (4 << 10), }, /* 4KB */
- { 0xd8, (64 << 10), }, /* sector */
- { 0xc7, (4 << 20), }, /* bulk */
- },
- },
- {
- "W25Q128", { 0xef, 0x40, 0x18 }, (16 << 20),
- { /* erase commands */
- { 0x20, (4 << 10), }, /* 4KB */
- { 0xd8, (64 << 10), }, /* sector */
- { 0xc7, (16 << 20), }, /* bulk */
- },
- },
-};
+#define IDCODE_LEN 3
/* Used to quickly bulk erase backing store */
static u8 sandbox_sf_0xff[0x1000];
*/
enum sandbox_sf_state state;
uint cmd;
- const void *cmd_data;
+ /* Erase size of current erase command */
+ uint erase_size;
/* Current position in the flash; used when reading/writing/etc... */
uint off;
/* How many address bytes we've consumed */
/* The current flash status (see STAT_XXX defines above) */
u16 status;
/* Data describing the flash we're emulating */
- const struct sandbox_spi_flash_data *data;
+ const struct spi_flash_params *data;
/* The file on disk to serv up data from */
int fd;
};
/* spec = idcode:file */
struct sandbox_spi_flash *sbsf;
const char *file;
- size_t i, len, idname_len;
- const struct sandbox_spi_flash_data *data;
+ size_t len, idname_len;
+ const struct spi_flash_params *data;
file = strchr(spec, ':');
if (!file) {
idname_len = file - spec;
++file;
- for (i = 0; i < ARRAY_SIZE(sandbox_sf_flashes); ++i) {
- data = &sandbox_sf_flashes[i];
+ for (data = spi_flash_params_table; data->name; data++) {
len = strlen(data->name);
if (idname_len != len)
continue;
if (!memcmp(spec, data->name, len))
break;
}
- if (i == ARRAY_SIZE(sandbox_sf_flashes)) {
+ if (!data->name) {
printf("sandbox_sf: unknown flash '%*s'\n", (int)idname_len,
spec);
goto error;
sbsf->pad_addr_bytes = 1;
case CMD_READ_ARRAY_SLOW:
case CMD_PAGE_PROGRAM:
- state_addr:
sbsf->state = SF_ADDR;
break;
case CMD_WRITE_DISABLE:
sbsf->status |= STAT_WEL;
break;
default: {
- size_t i;
-
- /* handle erase commands first */
- for (i = 0; i < MAX_ERASE_CMDS; ++i) {
- const struct sandbox_spi_flash_erase_commands *
- erase_cmd = &sbsf->data->erase_cmds[i];
-
- if (erase_cmd->cmd == 0x00)
- continue;
- if (sbsf->cmd != erase_cmd->cmd)
- continue;
-
- sbsf->cmd_data = erase_cmd;
- goto state_addr;
+ int flags = sbsf->data->flags;
+
+ /* we only support erase here */
+ if (sbsf->cmd == CMD_ERASE_CHIP) {
+ sbsf->erase_size = sbsf->data->sector_size *
+ sbsf->data->nr_sectors;
+ } else if (sbsf->cmd == CMD_ERASE_4K && (flags & SECT_4K)) {
+ sbsf->erase_size = 4 << 10;
+ } else if (sbsf->cmd == CMD_ERASE_32K && (flags & SECT_32K)) {
+ sbsf->erase_size = 32 << 10;
+ } else if (sbsf->cmd == CMD_ERASE_64K &&
+ !(flags & (SECT_4K | SECT_32K))) {
+ sbsf->erase_size = 64 << 10;
+ } else {
+ debug(" cmd unknown: %#x\n", sbsf->cmd);
+ return 1;
}
-
- debug(" cmd unknown: %#x\n", sbsf->cmd);
- return 1;
+ sbsf->state = SF_ADDR;
+ break;
}
}
u8 id;
debug(" id: off:%u tx:", sbsf->off);
- if (sbsf->off < IDCODE_LEN)
- id = sbsf->data->idcode[sbsf->off];
- else
+ if (sbsf->off < IDCODE_LEN) {
+ /* Extract correct byte from ID 0x00aabbcc */
+ id = sbsf->data->jedec >>
+ (8 * (IDCODE_LEN - 1 - sbsf->off));
+ } else {
id = 0;
- debug("%02x\n", id);
+ }
+ debug("%d %02x\n", sbsf->off, id);
tx[pos++] = id;
++sbsf->off;
break;
break;
case SF_ERASE:
case_sf_erase: {
- const struct sandbox_spi_flash_erase_commands *
- erase_cmd = sbsf->cmd_data;
-
if (!(sbsf->status & STAT_WEL)) {
puts("sandbox_sf: write enable not set before erase\n");
goto done;
}
/* verify address is aligned */
- if (sbsf->off & (erase_cmd->size - 1)) {
+ if (sbsf->off & (sbsf->erase_size - 1)) {
debug(" sector erase: cmd:%#x needs align:%#x, but we got %#x\n",
- erase_cmd->cmd, erase_cmd->size,
+ sbsf->cmd, sbsf->erase_size,
sbsf->off);
sbsf->status &= ~STAT_WEL;
goto done;
}
- debug(" sector erase addr: %u\n", sbsf->off);
+ debug(" sector erase addr: %u, size: %u\n", sbsf->off,
+ sbsf->erase_size);
cnt = bytes - pos;
sandbox_spi_tristate(&tx[pos], cnt);
* TODO(vapier@gentoo.org): latch WIP in status, and
* delay before clearing it ?
*/
- ret = sandbox_erase_part(sbsf, erase_cmd->size);
+ ret = sandbox_erase_part(sbsf, sbsf->erase_size);
sbsf->status &= ~STAT_WEL;
if (ret) {
debug("sandbox_sf: Erase failed\n");
{"M25P40", 0x202013, 0x0, 64 * 1024, 8, 0, 0},
{"M25P80", 0x202014, 0x0, 64 * 1024, 16, 0, 0},
{"M25P16", 0x202015, 0x0, 64 * 1024, 32, 0, 0},
+ {"M25PE16", 0x208015, 0x1000, 64 * 1024, 32, 0, 0},
+ {"M25PX16", 0x207115, 0x1000, 64 * 1024, 32, RD_EXTN, 0},
{"M25P32", 0x202016, 0x0, 64 * 1024, 64, 0, 0},
{"M25P64", 0x202017, 0x0, 64 * 1024, 128, 0, 0},
{"M25P128", 0x202018, 0x0, 256 * 1024, 64, 0, 0},
+ {"M25PX64", 0x207117, 0x0, 64 * 1024, 128, 0, SECT_4K},
{"N25Q32", 0x20ba16, 0x0, 64 * 1024, 64, RD_FULL, WR_QPP | SECT_4K},
{"N25Q32A", 0x20bb16, 0x0, 64 * 1024, 64, RD_FULL, WR_QPP | SECT_4K},
{"N25Q64", 0x20ba17, 0x0, 64 * 1024, 128, RD_FULL, WR_QPP | SECT_4K},
{"W25Q64DW", 0xef6017, 0x0, 64 * 1024, 128, RD_FULL, WR_QPP | SECT_4K},
{"W25Q128FW", 0xef6018, 0x0, 64 * 1024, 256, RD_FULL, WR_QPP | SECT_4K},
#endif
+ {}, /* Empty entry to terminate the list */
/*
* Note:
* Below paired flash devices has similar spi_flash params.
* Load U-Boot image from SPI flash into RAM
*/
- flash = spi_flash_probe(CONFIG_SPL_SPI_BUS, CONFIG_SPL_SPI_CS,
- CONFIG_SF_DEFAULT_SPEED, SPI_MODE_3);
+ flash = spi_flash_probe(CONFIG_SF_DEFAULT_BUS,
+ CONFIG_SF_DEFAULT_CS,
+ CONFIG_SF_DEFAULT_SPEED,
+ CONFIG_SF_DEFAULT_MODE);
if (!flash) {
puts("SPI probe failed.\n");
hang();
hw->autoneg_failed = 0;
hw->autoneg = 1;
hw->get_link_status = true;
+#ifndef CONFIG_E1000_NO_NVM
hw->eeprom_semaphore_present = true;
+#endif
hw->hw_addr = pci_map_bar(devno, PCI_BASE_ADDRESS_0,
PCI_REGION_MEM);
hw->mac_type = e1000_undefined;
*/
#define FEC_XFER_TIMEOUT 5000
+/*
+ * The standard 32-byte DMA alignment does not work on mx6solox, which requires
+ * 64-byte alignment in the DMA RX FEC buffer.
+ * Introduce the FEC_DMA_RX_MINALIGN which can cover mx6solox needs and also
+ * satisfies the alignment on other SoCs (32-bytes)
+ */
+#define FEC_DMA_RX_MINALIGN 64
+
#ifndef CONFIG_MII
#error "CONFIG_MII has to be defined!"
#endif
break;
}
- if (!timeout)
+ if (!timeout) {
ret = -EINVAL;
+ goto out;
+ }
- invalidate_dcache_range(addr, addr + size);
- if (readw(&fec->tbd_base[fec->tbd_index].status) & FEC_TBD_READY)
+ /*
+ * The TDAR bit is cleared when the descriptors are all out from TX
+ * but on mx6solox we noticed that the READY bit is still not cleared
+ * right after TDAR.
+ * These are two distinct signals, and in IC simulation, we found that
+ * TDAR always gets cleared prior than the READY bit of last BD becomes
+ * cleared.
+ * In mx6solox, we use a later version of FEC IP. It looks like that
+ * this intrinsic behaviour of TDAR bit has changed in this newer FEC
+ * version.
+ *
+ * Fix this by polling the READY bit of BD after the TDAR polling,
+ * which covers the mx6solox case and does not harm the other SoCs.
+ */
+ timeout = FEC_XFER_TIMEOUT;
+ while (--timeout) {
+ invalidate_dcache_range(addr, addr + size);
+ if (!(readw(&fec->tbd_base[fec->tbd_index].status) &
+ FEC_TBD_READY))
+ break;
+ }
+
+ if (!timeout)
ret = -EINVAL;
+out:
debug("fec_send: status 0x%x index %d ret %i\n",
readw(&fec->tbd_base[fec->tbd_index].status),
fec->tbd_index, ret);
/* Allocate RX buffers. */
/* Maximum RX buffer size. */
- size = roundup(FEC_MAX_PKT_SIZE, ARCH_DMA_MINALIGN);
+ size = roundup(FEC_MAX_PKT_SIZE, FEC_DMA_RX_MINALIGN);
for (i = 0; i < FEC_RBD_NUM; i++) {
- data = memalign(ARCH_DMA_MINALIGN, size);
+ data = memalign(FEC_DMA_RX_MINALIGN, size);
if (!data) {
printf("%s: error allocating rxbuf %d\n", __func__, i);
goto err_ring;
else if ((rcwsr13 & FSL_CORENET_RCWSR13_EC2) ==
FSL_CORENET_RCWSR13_EC2_FM1_DTSEC5_MII)
return PHY_INTERFACE_MODE_MII;
- else
- return PHY_INTERFACE_MODE_NONE;
}
switch (port) {
pci_hose_read_config_word(hose, dev, PCI_DEVICE_ID, &device);
pci_hose_read_config_word(hose, dev, PCI_CLASS_DEVICE, &class);
+#ifdef CONFIG_PCI_FIXUP_DEV
+ board_pci_fixup_dev(hose, dev, vendor, device, class);
+#endif
+
#ifdef CONFIG_PCI_SCAN_SHOW
indent++;
#define PCI_ACCESS_READ 0
#define PCI_ACCESS_WRITE 1
+#ifdef CONFIG_MX6SX
+#define MX6_DBI_ADDR 0x08ffc000
+#define MX6_IO_ADDR 0x08000000
+#define MX6_MEM_ADDR 0x08100000
+#define MX6_ROOT_ADDR 0x08f00000
+#else
#define MX6_DBI_ADDR 0x01ffc000
-#define MX6_DBI_SIZE 0x4000
#define MX6_IO_ADDR 0x01000000
-#define MX6_IO_SIZE 0x100000
#define MX6_MEM_ADDR 0x01100000
-#define MX6_MEM_SIZE 0xe00000
#define MX6_ROOT_ADDR 0x01f00000
+#endif
+#define MX6_DBI_SIZE 0x4000
+#define MX6_IO_SIZE 0x100000
+#define MX6_MEM_SIZE 0xe00000
#define MX6_ROOT_SIZE 0xfc000
/* PCIe Port Logic registers (memory-mapped) */
#define PHY_RX_OVRD_IN_LO_RX_DATA_EN (1 << 5)
#define PHY_RX_OVRD_IN_LO_RX_PLL_EN (1 << 3)
+#define PCIE_PHY_PUP_REQ (1 << 7)
+
/* iATU registers */
#define PCIE_ATU_VIEWPORT 0x900
#define PCIE_ATU_REGION_INBOUND (0x1 << 31)
static int imx6_pcie_assert_core_reset(void)
{
struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
-
+#if defined(CONFIG_MX6SX)
+ struct gpc *gpc_regs = (struct gpc *)GPC_BASE_ADDR;
+
+ /* SSP_EN is not used on MX6SX anymore */
+ setbits_le32(&iomuxc_regs->gpr[12], IOMUXC_GPR12_TEST_POWERDOWN);
+ /* Force PCIe PHY reset */
+ setbits_le32(&iomuxc_regs->gpr[5], IOMUXC_GPR5_PCIE_BTNRST);
+ /* Power up PCIe PHY */
+ setbits_le32(&gpc_regs->cntr, PCIE_PHY_PUP_REQ);
+#else
setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_TEST_POWERDOWN);
clrbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_REF_SSP_EN);
+#endif
return 0;
}
IOMUXC_GPR12_LOS_LEVEL_MASK,
IOMUXC_GPR12_LOS_LEVEL_9);
+#ifdef CONFIG_MX6SX
+ clrsetbits_le32(&iomuxc_regs->gpr[12],
+ IOMUXC_GPR12_RX_EQ_MASK,
+ IOMUXC_GPR12_RX_EQ_2);
+#endif
+
writel((0x0 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN1_OFFSET) |
(0x0 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_3P5DB_OFFSET) |
(20 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_6DB_OFFSET) |
*/
mdelay(50);
+#if defined(CONFIG_MX6SX)
+ /* SSP_EN is not used on MX6SX anymore */
+ clrbits_le32(&iomuxc_regs->gpr[12], IOMUXC_GPR12_TEST_POWERDOWN);
+ /* Clear PCIe PHY reset bit */
+ clrbits_le32(&iomuxc_regs->gpr[5], IOMUXC_GPR5_PCIE_BTNRST);
+#else
/* Enable PCIe */
clrbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_TEST_POWERDOWN);
setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_REF_SSP_EN);
+#endif
imx6_pcie_toggle_reset();
obj-$(CONFIG_MXS_AUART) += mxs_auart.o
obj-$(CONFIG_ARC_SERIAL) += serial_arc.o
obj-$(CONFIG_TEGRA_SERIAL) += serial_tegra.o
+obj-$(CONFIG_UNIPHIER_SERIAL) += serial_uniphier.o
ifndef CONFIG_SPL_BUILD
obj-$(CONFIG_USB_TTY) += usbtty.o
static void serial_find_console_or_panic(void)
{
+#ifdef CONFIG_OF_CONTROL
int node;
/* Check for a chosen console */
return;
cur_dev = NULL;
}
-
+#endif
/*
* Failing that, get the device with sequence number 0, or in extremis
* just the first serial device we can find. But we insist on having
serial_initfunc(arm_dcc_initialize);
serial_initfunc(mxs_auart_initialize);
serial_initfunc(arc_serial_initialize);
+serial_initfunc(uniphier_serial_initialize);
/**
* serial_register() - Register serial driver with serial driver core
arm_dcc_initialize();
mxs_auart_initialize();
arc_serial_initialize();
+ uniphier_serial_initialize();
serial_assign(default_serial_console()->name);
}
#define US1_TDRE (1 << 7)
#define US1_RDRF (1 << 5)
+#define US1_OR (1 << 3)
#define UC2_TE (1 << 3)
#define UC2_RE (1 << 2)
+#define CFIFO_TXFLUSH (1 << 7)
+#define CFIFO_RXFLUSH (1 << 6)
+#define SFIFO_RXOF (1 << 2)
+#define SFIFO_RXUF (1 << 0)
#define STAT_LBKDIF (1 << 31)
#define STAT_RXEDGIF (1 << 30)
static int lpuart_serial_getc(void)
{
- u8 status;
-
- while (!(__raw_readb(&base->us1) & US1_RDRF))
+ while (!(__raw_readb(&base->us1) & (US1_RDRF | US1_OR)))
WATCHDOG_RESET();
- status = __raw_readb(&base->us1);
- status |= US1_RDRF;
- __raw_writeb(status, &base->us1);
+ barrier();
return __raw_readb(&base->ud);
}
__raw_writeb(0, &base->umodem);
__raw_writeb(0, &base->uc1);
+ /* Disable FIFO and flush buffer */
+ __raw_writeb(0x0, &base->upfifo);
+ __raw_writeb(0x0, &base->utwfifo);
+ __raw_writeb(0x1, &base->urwfifo);
+ __raw_writeb(CFIFO_TXFLUSH | CFIFO_RXFLUSH, &base->ucfifo);
+
/* provide data bits, parity, stop bit, etc */
serial_setbrg();
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * Based on serial_ns16550.c
+ * (C) Copyright 2000
+ * Rob Taylor, Flying Pig Systems. robt@flyingpig.com.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <serial.h>
+
+#define UART_REG(x) \
+ u8 x; \
+ u8 postpad_##x[3];
+
+/*
+ * Note: Register map is slightly different from that of 16550.
+ */
+struct uniphier_serial {
+ UART_REG(rbr); /* 0x00 */
+ UART_REG(ier); /* 0x04 */
+ UART_REG(iir); /* 0x08 */
+ UART_REG(fcr); /* 0x0c */
+ u8 mcr; /* 0x10 */
+ u8 lcr;
+ u16 __postpad;
+ UART_REG(lsr); /* 0x14 */
+ UART_REG(msr); /* 0x18 */
+ u32 __none1;
+ u32 __none2;
+ u16 dlr;
+ u16 __postpad2;
+};
+
+#define thr rbr
+
+/*
+ * These are the definitions for the Line Control Register
+ */
+#define UART_LCR_WLS_8 0x03 /* 8 bit character length */
+
+/*
+ * These are the definitions for the Line Status Register
+ */
+#define UART_LSR_DR 0x01 /* Data ready */
+#define UART_LSR_THRE 0x20 /* Xmit holding register empty */
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void uniphier_serial_init(struct uniphier_serial *port)
+{
+ const unsigned int mode_x_div = 16;
+ unsigned int divisor;
+
+ writeb(UART_LCR_WLS_8, &port->lcr);
+
+ divisor = DIV_ROUND_CLOSEST(CONFIG_SYS_UNIPHIER_UART_CLK,
+ mode_x_div * gd->baudrate);
+
+ writew(divisor, &port->dlr);
+}
+
+static void uniphier_serial_setbrg(struct uniphier_serial *port)
+{
+ uniphier_serial_init(port);
+}
+
+static int uniphier_serial_tstc(struct uniphier_serial *port)
+{
+ return (readb(&port->lsr) & UART_LSR_DR) != 0;
+}
+
+static int uniphier_serial_getc(struct uniphier_serial *port)
+{
+ while (!uniphier_serial_tstc(port))
+ ;
+
+ return readb(&port->rbr);
+}
+
+static void uniphier_serial_putc(struct uniphier_serial *port, const char c)
+{
+ if (c == '\n')
+ uniphier_serial_putc(port, '\r');
+
+ while (!(readb(&port->lsr) & UART_LSR_THRE))
+ ;
+
+ writeb(c, &port->thr);
+}
+
+static struct uniphier_serial *serial_ports[4] = {
+#ifdef CONFIG_SYS_UNIPHIER_SERIAL_BASE0
+ (struct uniphier_serial *)CONFIG_SYS_UNIPHIER_SERIAL_BASE0,
+#else
+ NULL,
+#endif
+#ifdef CONFIG_SYS_UNIPHIER_SERIAL_BASE1
+ (struct uniphier_serial *)CONFIG_SYS_UNIPHIER_SERIAL_BASE1,
+#else
+ NULL,
+#endif
+#ifdef CONFIG_SYS_UNIPHIER_SERIAL_BASE2
+ (struct uniphier_serial *)CONFIG_SYS_UNIPHIER_SERIAL_BASE2,
+#else
+ NULL,
+#endif
+#ifdef CONFIG_SYS_UNIPHIER_SERIAL_BASE3
+ (struct uniphier_serial *)CONFIG_SYS_UNIPHIER_SERIAL_BASE3,
+#else
+ NULL,
+#endif
+};
+
+/* Multi serial device functions */
+#define DECLARE_ESERIAL_FUNCTIONS(port) \
+ static int eserial##port##_init(void) \
+ { \
+ uniphier_serial_init(serial_ports[port]); \
+ return 0 ; \
+ } \
+ static void eserial##port##_setbrg(void) \
+ { \
+ uniphier_serial_setbrg(serial_ports[port]); \
+ } \
+ static int eserial##port##_getc(void) \
+ { \
+ return uniphier_serial_getc(serial_ports[port]); \
+ } \
+ static int eserial##port##_tstc(void) \
+ { \
+ return uniphier_serial_tstc(serial_ports[port]); \
+ } \
+ static void eserial##port##_putc(const char c) \
+ { \
+ uniphier_serial_putc(serial_ports[port], c); \
+ }
+
+/* Serial device descriptor */
+#define INIT_ESERIAL_STRUCTURE(port, __name) { \
+ .name = __name, \
+ .start = eserial##port##_init, \
+ .stop = NULL, \
+ .setbrg = eserial##port##_setbrg, \
+ .getc = eserial##port##_getc, \
+ .tstc = eserial##port##_tstc, \
+ .putc = eserial##port##_putc, \
+ .puts = default_serial_puts, \
+}
+
+#if defined(CONFIG_SYS_UNIPHIER_SERIAL_BASE0)
+DECLARE_ESERIAL_FUNCTIONS(0);
+struct serial_device uniphier_serial0_device =
+ INIT_ESERIAL_STRUCTURE(0, "ttyS0");
+#endif
+#if defined(CONFIG_SYS_UNIPHIER_SERIAL_BASE1)
+DECLARE_ESERIAL_FUNCTIONS(1);
+struct serial_device uniphier_serial1_device =
+ INIT_ESERIAL_STRUCTURE(1, "ttyS1");
+#endif
+#if defined(CONFIG_SYS_UNIPHIER_SERIAL_BASE2)
+DECLARE_ESERIAL_FUNCTIONS(2);
+struct serial_device uniphier_serial2_device =
+ INIT_ESERIAL_STRUCTURE(2, "ttyS2");
+#endif
+#if defined(CONFIG_SYS_UNIPHIER_SERIAL_BASE3)
+DECLARE_ESERIAL_FUNCTIONS(3);
+struct serial_device uniphier_serial3_device =
+ INIT_ESERIAL_STRUCTURE(3, "ttyS3");
+#endif
+
+__weak struct serial_device *default_serial_console(void)
+{
+#if defined(CONFIG_SYS_UNIPHIER_SERIAL_BASE0)
+ return &uniphier_serial0_device;
+#elif defined(CONFIG_SYS_UNIPHIER_SERIAL_BASE1)
+ return &uniphier_serial1_device;
+#elif defined(CONFIG_SYS_UNIPHIER_SERIAL_BASE2)
+ return &uniphier_serial2_device;
+#elif defined(CONFIG_SYS_UNIPHIER_SERIAL_BASE3)
+ return &uniphier_serial3_device;
+#else
+#error "No uniphier serial ports configured."
+#endif
+}
+
+void uniphier_serial_initialize(void)
+{
+#if defined(CONFIG_SYS_UNIPHIER_SERIAL_BASE0)
+ serial_register(&uniphier_serial0_device);
+#endif
+#if defined(CONFIG_SYS_UNIPHIER_SERIAL_BASE1)
+ serial_register(&uniphier_serial1_device);
+#endif
+#if defined(CONFIG_SYS_UNIPHIER_SERIAL_BASE2)
+ serial_register(&uniphier_serial2_device);
+#endif
+#if defined(CONFIG_SYS_UNIPHIER_SERIAL_BASE3)
+ serial_register(&uniphier_serial3_device);
+#endif
+}
if (space) {
write_buffer (&usbtty_output);
- n = MIN (space, MIN (len, maxlen));
+ n = min(space, min(len, maxlen));
buf_push (&usbtty_output, str, n);
str += n;
space_avail =
current_urb->buffer_length -
current_urb->actual_length;
- popnum = MIN (space_avail, buf->size);
+ popnum = min(space_avail, buf->size);
if (popnum == 0)
break;
static struct kwspi_registers *spireg = (struct kwspi_registers *)KW_SPI_BASE;
-u32 cs_spi_mpp_back[2];
+static u32 cs_spi_mpp_back[2];
struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
unsigned int max_hz, unsigned int mode)
if (!slave)
return NULL;
- writel(~KWSPI_CSN_ACT | KWSPI_SMEMRDY, &spireg->ctrl);
+ writel(KWSPI_SMEMRDY, &spireg->ctrl);
/* calculate spi clock prescaller using max_hz */
data = ((CONFIG_SYS_TCLK / 2) / max_hz) + 0x10;
/* program spi clock prescaller using max_hz */
writel(KWSPI_ADRLEN_3BYTE | data, &spireg->cfg);
- debug("data = 0x%08x \n", data);
+ debug("data = 0x%08x\n", data);
writel(KWSPI_SMEMRDIRQ, &spireg->irq_cause);
writel(KWSPI_IRQMASK, &spireg->irq_mask);
/* set new spi mpp and save current mpp config */
kirkwood_mpp_conf(spi_mpp_config, spi_mpp_backup);
-
#endif
return board_spi_claim_bus(slave);
*/
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
- return (bus == 0 && (cs == 0 || cs == 1));
+ return bus == 0 && (cs == 0 || cs == 1);
}
#endif
void spi_cs_activate(struct spi_slave *slave)
{
- writel(readl(&spireg->ctrl) | KWSPI_IRQUNMASK, &spireg->ctrl);
+ setbits_le32(&spireg->ctrl, KWSPI_CSN_ACT);
}
void spi_cs_deactivate(struct spi_slave *slave)
{
- writel(readl(&spireg->ctrl) & KWSPI_IRQMASK, &spireg->ctrl);
+ clrbits_le32(&spireg->ctrl, KWSPI_CSN_ACT);
}
int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
* handle data in 8-bit chunks
* TBD: 2byte xfer mode to be enabled
*/
- writel(((readl(&spireg->cfg) & ~KWSPI_XFERLEN_MASK) |
- KWSPI_XFERLEN_1BYTE), &spireg->cfg);
+ clrsetbits_le32(&spireg->cfg, KWSPI_XFERLEN_MASK, KWSPI_XFERLEN_1BYTE);
while (bitlen > 4) {
debug("loopstart bitlen %d\n", bitlen);
/* Shift data so it's msb-justified */
if (dout)
- tmpdout = *(u32 *) dout & 0x0ff;
+ tmpdout = *(u32 *)dout & 0xff;
- writel(~KWSPI_SMEMRDIRQ, &spireg->irq_cause);
+ clrbits_le32(&spireg->irq_cause, KWSPI_SMEMRDIRQ);
writel(tmpdout, &spireg->dout); /* Write the data out */
debug("*** spi_xfer: ... %08x written, bitlen %d\n",
tmpdout, bitlen);
if (readl(&spireg->irq_cause) & KWSPI_SMEMRDIRQ) {
isread = 1;
tmpdin = readl(&spireg->din);
- debug
- ("spi_xfer: din %p..%08x read\n",
- din, tmpdin);
+ debug("spi_xfer: din %p..%08x read\n",
+ din, tmpdin);
if (din) {
- *((u8 *) din) = (u8) tmpdin;
+ *((u8 *)din) = (u8)tmpdin;
din += 1;
}
if (dout)
MXC_SPI_BASE_ADDRESSES
};
+__weak int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+ return -1;
+}
+
#define OUT MXC_GPIO_DIRECTION_OUT
#define reg_read readl
{
}
-static int decode_cs(struct mxc_spi_slave *mxcs, unsigned int cs)
+/*
+ * Some SPI devices require active chip-select over multiple
+ * transactions, we achieve this using a GPIO. Still, the SPI
+ * controller has to be configured to use one of its own chipselects.
+ * To use this feature you have to implement board_spi_cs_gpio() to assign
+ * a gpio value for each cs (-1 if cs doesn't need to use gpio).
+ * You must use some unused on this SPI controller cs between 0 and 3.
+ */
+static int setup_cs_gpio(struct mxc_spi_slave *mxcs,
+ unsigned int bus, unsigned int cs)
{
int ret;
- /*
- * Some SPI devices require active chip-select over multiple
- * transactions, we achieve this using a GPIO. Still, the SPI
- * controller has to be configured to use one of its own chipselects.
- * To use this feature you have to call spi_setup_slave() with
- * cs = internal_cs | (gpio << 8), and you have to use some unused
- * on this SPI controller cs between 0 and 3.
- */
- if (cs > 3) {
- mxcs->gpio = cs >> 8;
- cs &= 3;
- ret = gpio_direction_output(mxcs->gpio, !(mxcs->ss_pol));
- if (ret) {
- printf("mxc_spi: cannot setup gpio %d\n", mxcs->gpio);
- return -EINVAL;
- }
- } else {
- mxcs->gpio = -1;
+ mxcs->gpio = board_spi_cs_gpio(bus, cs);
+ if (mxcs->gpio == -1)
+ return 0;
+
+ ret = gpio_direction_output(mxcs->gpio, !(mxcs->ss_pol));
+ if (ret) {
+ printf("mxc_spi: cannot setup gpio %d\n", mxcs->gpio);
+ return -EINVAL;
}
- return cs;
+ return 0;
}
struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
mxcs->ss_pol = (mode & SPI_CS_HIGH) ? 1 : 0;
- ret = decode_cs(mxcs, cs);
+ ret = setup_cs_gpio(mxcs, bus, cs);
if (ret < 0) {
free(mxcs);
return NULL;
}
- cs = ret;
-
mxcs->base = spi_bases[bus];
ret = spi_cfg_mxc(mxcs, cs, max_hz, mode);
/*
* Copyright (c) 2011 The Chromium OS Authors.
* Copyright (C) 2009 NVIDIA, Corporation
+ * Copyright (C) 2007-2008 SMSC (Steve Glendinning)
*
* SPDX-License-Identifier: GPL-2.0+
*/
UDCDBGA("urb->buffer %p, buffer_length %d, actual_length %d",
urb->buffer, urb->buffer_length, urb->actual_length);
- last = MIN(urb->actual_length - endpoint->sent,
+ last = min(urb->actual_length - endpoint->sent,
endpoint->tx_packetSize);
if (last) {
align = ((ulong)cp % sizeof(int));
if (align)
- last = MIN(last, sizeof(int) - align);
+ last = min(last, sizeof(int) - align);
UDCDBGA("endpoint->sent %d, tx_packetSize %d, last %d",
endpoint->sent, endpoint->tx_packetSize, last);
/*copy_config(urb, &report_descriptor->bData[0], report_descriptor->wLength, max); */
if (max - urb->actual_length > 0) {
int length =
- MIN (report_descriptor->wLength,
+ min(report_descriptor->wLength,
max - urb->actual_length);
memcpy (urb->buffer + urb->actual_length,
&report_descriptor->bData[0], length);
*
* SPDX-License-Identifier: GPL-2.0+
*/
+#include <config.h>
#include <common.h>
#include <errno.h>
#include <malloc.h>
#include <linux/compiler.h>
#include <version.h>
#include <g_dnl.h>
+#ifdef CONFIG_FASTBOOT_FLASH_MMC_DEV
+#include <fb_mmc.h>
+#endif
#define FASTBOOT_VERSION "0.4"
struct f_fastboot {
struct usb_function usb_function;
- /* IN/OUT EP's and correspoinding requests */
+ /* IN/OUT EP's and corresponding requests */
struct usb_ep *in_ep, *out_ep;
struct usb_request *in_req, *out_req;
};
}
DECLARE_GADGET_BIND_CALLBACK(usb_dnl_fastboot, fastboot_add);
-int fastboot_tx_write(const char *buffer, unsigned int buffer_size)
+static int fastboot_tx_write(const char *buffer, unsigned int buffer_size)
{
struct usb_request *in_req = fastboot_func->in_req;
int ret;
strsep(&cmd, ":");
if (!cmd) {
+ error("missing variable\n");
fastboot_tx_write_str("FAILmissing var");
return;
}
else
strcpy(response, "FAILValue not set");
} else {
+ error("unknown variable: %s\n", cmd);
strcpy(response, "FAILVariable not implemented");
}
fastboot_tx_write_str(response);
fastboot_tx_write_str("OKAY");
}
+#ifdef CONFIG_FASTBOOT_FLASH
+static void cb_flash(struct usb_ep *ep, struct usb_request *req)
+{
+ char *cmd = req->buf;
+ char response[RESPONSE_LEN];
+
+ strsep(&cmd, ":");
+ if (!cmd) {
+ error("missing partition name\n");
+ fastboot_tx_write_str("FAILmissing partition name");
+ return;
+ }
+
+ strcpy(response, "FAILno flash device defined");
+#ifdef CONFIG_FASTBOOT_FLASH_MMC_DEV
+ fb_mmc_flash_write(cmd, (void *)CONFIG_USB_FASTBOOT_BUF_ADDR,
+ download_bytes, response);
+#endif
+ fastboot_tx_write_str(response);
+}
+#endif
+
struct cmd_dispatch_info {
char *cmd;
void (*cb)(struct usb_ep *ep, struct usb_request *req);
.cmd = "boot",
.cb = cb_boot,
},
+#ifdef CONFIG_FASTBOOT_FLASH
+ {
+ .cmd = "flash",
+ .cb = cb_flash,
+ },
+#endif
};
static void rx_handler_command(struct usb_ep *ep, struct usb_request *req)
}
}
- if (!func_cb)
+ if (!func_cb) {
+ error("unknown command: %s\n", cmdbuf);
fastboot_tx_write_str("FAILunknown command");
- else
+ } else {
func_cb(ep, req);
+ }
if (req->status == 0) {
*cmdbuf = '\0';
pkt_len = urb->actual_length - epi->sent;
if (pkt_len > epi->tx_packetSize || pkt_len > EP_MAX_PKT) {
- pkt_len = MIN (epi->tx_packetSize, EP_MAX_PKT);
+ pkt_len = min(epi->tx_packetSize, EP_MAX_PKT);
}
for (x = 0; x < pkt_len; x++) {
/* TX ACK : USB 2.0 8.7.2, Toggle PID, Advance TX */
epi->sent += pkt_len;
- epi->last = MIN (urb->actual_length - epi->sent, epi->tx_packetSize);
+ epi->last = min(urb->actual_length - epi->sent, epi->tx_packetSize);
TOGGLE_TX_PID (ep_ref[ep].pid);
if (epi->sent >= epi->tx_urb->actual_length) {
if (!urb || !urb->actual_length)
return -1;
- n = MIN(urb->actual_length - endpoint->sent, endpoint->tx_packetSize);
+ n = min(urb->actual_length - endpoint->sent, endpoint->tx_packetSize);
if (n <= 0)
return -1;
}
/* Enable USB Host clock */
+#ifdef CPU_HAS_PCR
+ at91_periph_clk_enable(ATMEL_ID_UHPHS);
+#else
writel(1 << ATMEL_ID_UHPHS, &pmc->pcer);
+#endif
*hccr = (struct ehci_hccr *)ATMEL_BASE_EHCI;
*hcor = (struct ehci_hcor *)((uint32_t)*hccr +
ulong start_time, tmp_time;
/* Disable USB Host Clock */
+#ifdef CPU_HAS_PCR
+ at91_periph_clk_disable(ATMEL_ID_UHPHS);
+#else
writel(1 << ATMEL_ID_UHPHS, &pmc->pcdr);
+#endif
start_time = get_timer(0);
/* Disable UTMI PLL */
#endif
/* Enable USB host clock. */
-#ifdef CONFIG_SAMA5D3
- writel(1 << (ATMEL_ID_UHP - 32), &pmc->pcer1);
+#ifdef CPU_HAS_PCR
+ at91_periph_clk_enable(ATMEL_ID_UHP);
#else
writel(1 << ATMEL_ID_UHP, &pmc->pcer);
#endif
at91_pmc_t *pmc = (at91_pmc_t *)ATMEL_BASE_PMC;
/* Disable USB host clock. */
-#ifdef CONFIG_SAMA5D3
- writel(1 << (ATMEL_ID_UHP - 32), &pmc->pcdr1);
+#ifdef CPU_HAS_PCR
+ at91_periph_clk_disable(ATMEL_ID_UHP);
#else
writel(1 << ATMEL_ID_UHP, &pmc->pcdr);
#endif
--- /dev/null
+#
+# Device Tree Control
+#
+# TODO:
+# This feature is not currently supported for SPL,
+# but this restriction should be removed in the future.
+
+config SUPPORT_OF_CONTROL
+ bool
+
+menu "Device Tree Control"
+ depends on !SPL_BUILD
+ depends on SUPPORT_OF_CONTROL
+
+config OF_CONTROL
+ bool "Run-time configuration via Device Tree"
+ help
+ This feature provides for run-time configuration of U-Boot
+ via a flattened device tree.
+
+choice
+ prompt "Provider of DTB for DT control"
+ depends on OF_CONTROL
+
+config OF_SEPARATE
+ bool "Separate DTB for DT control"
+ depends on !SANDBOX
+ help
+ If this option is enabled, the device tree will be built and
+ placed as a separate u-boot.dtb file alongside the U-Boot image.
+
+config OF_EMBED
+ bool "Embedded DTB for DT control"
+ help
+ If this option is enabled, the device tree will be picked up and
+ built into the U-Boot image.
+
+config OF_HOSTFILE
+ bool "Host filed DTB for DT control"
+ depends on SANDBOX
+ help
+ If this option is enabled, DTB will be read from a file on startup.
+ This is only useful for Sandbox. Use the -d flag to U-Boot to
+ specify the file to read.
+
+endchoice
+
+config DEFAULT_DEVICE_TREE
+ string "Default Device Tree for DT control"
+ help
+ This option specifies the default Device Tree used for DT control.
+ It can be overrided from the command line:
+ $ make DEVICE_TREE=<device-tree-name>
+
+endmenu
ELF := $(strip $(extra-y))
extra-y += $(addsuffix .srec,$(extra-y)) $(addsuffix .bin,$(extra-y))
-clean-files := $(extra-) $(addsuffix .srec,$(extra-)) $(addsuffix .bin,$(extra-))
+clean-files := *.srec *.bin
COBJS := $(ELF:=.o)
--- /dev/null
+#
+# File system configuration
+#
+
+menu "File systems"
+
+source "fs/ext4/Kconfig"
+
+source "fs/reiserfs/Kconfig"
+
+source "fs/fat/Kconfig"
+
+source "fs/jffs2/Kconfig"
+
+source "fs/ubifs/Kconfig"
+
+source "fs/cramfs/Kconfig"
+
+endmenu
while (bseen < array_len) {
struct zap_leaf_array *la = &ZAP_LEAF_CHUNK(l, blksft, chunk).l_array;
- int toread = MIN(array_len - bseen, ZAP_LEAF_ARRAY_BYTES);
+ int toread = min(array_len - bseen, ZAP_LEAF_ARRAY_BYTES);
if (chunk >= ZAP_LEAF_NUMCHUNKS(blksft))
return 0;
while (bseen < array_len) {
struct zap_leaf_array *la = &ZAP_LEAF_CHUNK(l, blksft, chunk).l_array;
- int toread = MIN(array_len - bseen, ZAP_LEAF_ARRAY_BYTES);
+ int toread = min(array_len - bseen, ZAP_LEAF_ARRAY_BYTES);
if (chunk >= ZAP_LEAF_NUMCHUNKS(blksft))
/* Don't use errno because this error is to be ignored. */
data->file_start = blkid * blksz;
data->file_end = data->file_start + blksz;
- movesize = MIN(length, data->file_end - (int) file->offset - red);
+ movesize = min(length, data->file_end - (int)file->offset - red);
memmove(buf, data->file_buf + file->offset + red
- data->file_start, movesize);
typeof(Y) __y = (Y); \
(__x > __y) ? __x : __y; })
-#define MIN(x, y) min(x, y)
-#define MAX(x, y) max(x, y)
-
#define min3(X, Y, Z) \
({ typeof(X) __x = (X); \
typeof(Y) __y = (Y); \
__x > __y ? (__x > __z ? __x : __z) : \
(__y > __z ? __y : __z); })
-#define MIN3(x, y, z) min3(x, y, z)
-#define MAX3(x, y, z) max3(x, y, z)
-
/*
* Return the absolute value of a number.
*
#endif /* USE_HOSTCC */
-/* compiler options */
-#define uninitialized_var(x) x = x
-
#define likely(x) __builtin_expect(!!(x), 1)
#define unlikely(x) __builtin_expect(!!(x), 0)
+++ /dev/null
-/*
- * config_cmd_defaults.h - sane defaults for everyone
- *
- * Copyright (c) 2010-2011 Analog Devices Inc.
- *
- * Licensed under the GPL-2 or later.
- */
-
-#ifndef _CONFIG_CMD_DEFAULTS_H_
-#define _CONFIG_CMD_DEFAULTS_H_
-
-#define CONFIG_CMD_BOOTM 1
-#define CONFIG_CMD_CRC32 1
-#define CONFIG_CMD_EXPORTENV 1
-#define CONFIG_CMD_GO 1
-#define CONFIG_CMD_IMPORTENV 1
-
-#endif
#endif
#ifdef CONFIG_CMD_SCSI
-#define BOOTENV_SHARED_SCSI BOOTENV_SHARED_BLKDEV(scsi)
+#define BOOTENV_RUN_SCSI_INIT "run scsi_init; "
+#define BOOTENV_SET_SCSI_NEED_INIT "setenv scsi_need_init; "
+#define BOOTENV_SHARED_SCSI \
+ "scsi_init=" \
+ "if ${scsi_need_init}; then " \
+ "setenv scsi_need_init false; " \
+ "scsi scan; " \
+ "fi\0" \
+ \
+ "scsi_boot=" \
+ BOOTENV_RUN_SCSI_INIT \
+ BOOTENV_SHARED_BLKDEV_BODY(scsi)
#define BOOTENV_DEV_SCSI BOOTENV_DEV_BLKDEV
#define BOOTENV_DEV_NAME_SCSI BOOTENV_DEV_NAME_BLKDEV
#else
+#define BOOTENV_RUN_SCSI_INIT
+#define BOOTENV_SET_SCSI_NEED_INIT
#define BOOTENV_SHARED_SCSI
#define BOOTENV_DEV_SCSI \
BOOT_TARGET_DEVICES_references_SCSI_without_CONFIG_CMD_SCSI
\
BOOT_TARGET_DEVICES(BOOTENV_DEV) \
\
- "bootcmd=" BOOTENV_SET_USB_NEED_INIT \
+ "bootcmd=" BOOTENV_SET_USB_NEED_INIT BOOTENV_SET_SCSI_NEED_INIT \
"for target in ${boot_targets}; do " \
"run bootcmd_${target}; " \
"done\0"
#endif
/* EEPROM */
+#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define __USB_PHY_TYPE ulpi
+#ifdef CONFIG_PPC_B4860
+#define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null," \
+ "bank_intlv=cs0_cs1;" \
+ "en_cpc:cpc2;"
+#else
+#define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;"
+#endif
+
#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=fsl_ddr:ctlr_intlv=null," \
- "bank_intlv=cs0_cs1;" \
+ HWCONFIG \
"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
"netdev=eth0\0" \
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t104xrdb/t1040_rcw.cfg
#endif
#ifdef CONFIG_T1042RDB_PI
+#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t104xrdb/t1042_pi_rcw.cfg
+#endif
+#ifdef CONFIG_T1042RDB
#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t104xrdb/t1042_rcw.cfg
#endif
/* I2C bus multiplexer */
#define I2C_MUX_PCA_ADDR 0x70
-#ifdef CONFIG_T1040RDB
+#if defined(CONFIG_T1040RDB) || defined(CONFIG_T1042RDB)
#define I2C_MUX_CH_DEFAULT 0x8
#endif
#define CONFIG_FSL_ESPI
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_BAR
#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE 0
#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME
-#ifdef CONFIG_T1040RDB
+#if defined(CONFIG_T1040RDB) || defined(CONFIG_T1042RDB)
#define CONFIG_QE
#define CONFIG_U_QE
#endif
#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
#endif
-#ifdef CONFIG_T1040RDB
+#if defined(CONFIG_T1040RDB) || defined(CONFIG_T1042RDB)
#if defined(CONFIG_SPIFLASH)
#define CONFIG_SYS_QE_FW_ADDR 0x130000
#elif defined(CONFIG_SDCARD)
#endif
#ifdef CONFIG_FMAN_ENET
-#ifdef CONFIG_T1040RDB
+#if defined(CONFIG_T1040RDB) || defined(CONFIG_T1042RDB)
#define CONFIG_SYS_SGMII1_PHY_ADDR 0x03
#endif
#define CONFIG_SYS_RGMII1_PHY_ADDR 0x01
#define CONFIG_BAUDRATE 115200
#define __USB_PHY_TYPE utmi
+#define RAMDISKFILE "t104xrdb/ramdisk.uboot"
#ifdef CONFIG_T1040RDB
#define FDTFILE "t1040rdb/t1040rdb.dtb"
-#define RAMDISKFILE "t1040rdb/ramdisk.uboot"
-#elif CONFIG_T1042RDB_PI
-#define FDTFILE "t1040rdb_pi/t1040rdb_pi.dtb"
-#define RAMDISKFILE "t1040rdb_pi/ramdisk.uboot"
+#elif defined(CONFIG_T1042RDB_PI)
+#define FDTFILE "t1042rdb_pi/t1042rdb_pi.dtb"
+#elif defined(CONFIG_T1042RDB)
+#define FDTFILE "t1042rdb/t1042rdb.dtb"
#endif
#ifdef CONFIG_FSL_DIU_FB
# define CONFIG_TIMESTAMP
# define CONFIG_LZO
# ifdef CONFIG_ENABLE_VBOOT
-# define CONFIG_OF_CONTROL
-# define CONFIG_OF_SEPARATE
-# define CONFIG_DEFAULT_DEVICE_TREE am335x-boneblack
# define CONFIG_FIT_SIGNATURE
# define CONFIG_RSA
# endif
"nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
"ip=dhcp\0" \
"bootenv=uEnv.txt\0" \
+ "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
+ "source ${loadaddr}\0" \
"loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
"importbootenv=echo Importing environment from mmc ...; " \
"env import -t -r $loadaddr $filesize\0" \
"mmcboot=mmc dev ${mmcdev}; " \
"if mmc rescan; then " \
"echo SD/MMC found on device ${mmcdev};" \
- "if run loadbootenv; then " \
- "echo Loaded environment from ${bootenv};" \
- "run importbootenv;" \
- "fi;" \
- "if test -n $uenvcmd; then " \
- "echo Running uenvcmd ...;" \
- "run uenvcmd;" \
- "fi;" \
- "if run loadimage; then " \
- "run mmcloados;" \
- "fi;" \
+ "if run loadbootscript; then " \
+ "run bootscript;" \
+ "else " \
+ "if run loadbootenv; then " \
+ "echo Loaded environment from ${bootenv};" \
+ "run importbootenv;" \
+ "fi;" \
+ "if test -n $uenvcmd; then " \
+ "echo Running uenvcmd ...;" \
+ "run uenvcmd;" \
+ "fi;" \
+ "if run loadimage; then " \
+ "run mmcloados;" \
+ "fi;" \
+ "fi ;" \
"fi;\0" \
"spiboot=echo Booting from spi ...; " \
"run spiargs; " \
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SPL_SPI_BUS 0
-#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
/* Allow tracing to be enabled */
#define CONFIG_TRACE
#define CONFIG_POWER_I2C
#define CONFIG_POWER_MAX77686
-#define CONFIG_DEFAULT_DEVICE_TREE exynos5250-arndale
#define CONFIG_PREBOOT
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_OF_LIBFDT
+#define CONFIG_SYS_GENERIC_BOARD
/* general purpose I/O */
#define CONFIG_AT91_GPIO
#define CONFIG_CMD_BOOTZ
#define CONFIG_OF_LIBFDT
+#define CONFIG_SYS_GENERIC_BOARD
+
#define CONFIG_ATMEL_LEGACY
#define CONFIG_AT91_GPIO 1
#define CONFIG_AT91_GPIO_PULLUP 1
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
/* VDD core PMIC */
#define CONFIG_TEGRA_VDD_CORE_TPS62366A_SET1
-/* Enable fdt support for Beaver. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra30-beaver
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra30 (Beaver) # "
#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Beaver"
*/
#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_SIZE 0x400
-#undef CONFIG_CMD_EXPORTENV
-#undef CONFIG_CMD_IMPORTENV
/*
#define CONFIG_CMD_MEMORY
#undef CONFIG_GZIP
#undef CONFIG_ZLIB
-#undef CONFIG_CMD_BOOTM
#undef CONFIG_BOOTM_RTEMS
#undef CONFIG_BOOTM_LINUX
#define CONFIG_MISC_INIT_R
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 0
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
#define CONFIG_MISC_INIT_R
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 1
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/* define to enable run status via led */
/* #define CONFIG_STATUS_LED */
*/
#define CONFIG_MISC_INIT_R
#define CONFIG_UART_CONSOLE 0
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
#define CONFIG_MISC_INIT_R
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 1
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
*/
#define CONFIG_MISC_INIT_R
#define CONFIG_UART_CONSOLE 0
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
#define CONFIG_MISC_INIT_R
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 0
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
*/
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 0
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/* FLASH/ETHERNET uses the same async bank */
#define SHARED_RESOURCES 1
#define CONFIG_MISC_INIT_R
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 0
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/* Define if want to do post memory test */
#undef CONFIG_POST
*/
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 0
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 1
#define CONFIG_BFIN_SPI_IMG_SIZE 0x50000
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
#define CONFIG_ADI_GPIO2
#define CONFIG_UART_CONSOLE 0
#define CONFIG_BAUDRATE 57600
#define CONFIG_SYS_PROMPT "Acvilon> "
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
* Misc Settings
*/
#define CONFIG_UART_CONSOLE 0
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Run core 1 from L1 SRAM start address when init uboot on core 0
#define CONFIG_BOOTCOMMAND "run nandboot"
#define CONFIG_BOOTDELAY 2
#define CONFIG_LOADADDR 0x2000000
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
#undef CONFIG_CMD_NFS
#undef CONFIG_CMD_SETGETDCR
#undef CONFIG_CMD_XIMG
-#undef CONFIG_CMD_CRC32
/* define command we need always */
#define CONFIG_CMD_ECHO
#define CONFIG_CMD_SOURCE
/* VDD core PMIC */
#define CONFIG_TEGRA_VDD_CORE_TPS62361B_SET3
-/* Enable fdt support for Cardhu. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra30-cardhu
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra30 (Cardhu) # "
#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Cardhu"
#define FLASHBOOT_ENV_SETTINGS \
"flashboot=flread 20040000 1000000 300000;" \
"bootm 0x1000000\0"
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
#define CONFIG_UART_CONSOLE 0
#define CONFIG_BOOTCOMMAND "run flashboot"
#define FLASHBOOT_ENV_SETTINGS "flashboot=bootm 0x20040000\0"
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
"flashboot=flread 20040000 1000000 3c0000;" \
"bootm 0x1000000\0"
#define CONFIG_BOARD_SIZE_LIMIT $$((384 * 1024))
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
"flashboot=flread 20040000 1000000 300000;" \
"bootm 0x1000000\0"
#define CONFIG_BOARD_SIZE_LIMIT $$((384 * 1024))
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
#define CONFIG_UART_CONSOLE 1
#define CONFIG_BOOTCOMMAND "run flashboot"
#define FLASHBOOT_ENV_SETTINGS "flashboot=bootm 0x20040000\0"
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
#define CONFIG_ADI_GPIO2
#define CONFIG_UART_CONSOLE 0
#define CONFIG_BOOTCOMMAND "run flashboot"
#define FLASHBOOT_ENV_SETTINGS "flashboot=bootm 0x20040000\0"
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
--- /dev/null
+/*
+ * Config file for Compulab CM-FX6 board
+ *
+ * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Nikita Kiryanov <nikita@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_CM_FX6_H
+#define __CONFIG_CM_FX6_H
+
+#include <asm/arch/imx-regs.h>
+#include <config_distro_defaults.h>
+#include "mx6_common.h"
+
+/* Machine config */
+#define CONFIG_MX6
+#define CONFIG_SYS_LITTLE_ENDIAN
+#define CONFIG_MACH_TYPE 4273
+#define CONFIG_SYS_HZ 1000
+
+/* Display information on boot */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_TIMESTAMP
+
+/* CMD */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_GREPENV
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_XIMG
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMLS
+
+/* MMC */
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_USDHC_NUM 3
+#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
+
+/* RAM */
+#define PHYS_SDRAM_1 MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_2 MMDC1_ARB_BASE_ADDR
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_NR_DRAM_BANKS 2
+#define CONFIG_SYS_MEMTEST_START 0x10000000
+#define CONFIG_SYS_MEMTEST_END 0x10010000
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* Serial console */
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART4_BASE
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
+
+/* Shell */
+#define CONFIG_SYS_PROMPT "CM-FX6 # "
+#define CONFIG_SYS_CBSIZE 1024
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+
+/* SPI flash */
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_BUS 0
+#define CONFIG_SF_DEFAULT_CS 0
+#define CONFIG_SF_DEFAULT_SPEED 25000000
+#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
+
+/* Environment */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
+#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SECT_SIZE (64 * 1024)
+#define CONFIG_ENV_SIZE (8 * 1024)
+#define CONFIG_ENV_OFFSET (768 * 1024)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "kernel=uImage-cm-fx6\0" \
+ "autoload=no\0" \
+ "loadaddr=0x10800000\0" \
+ "fdtaddr=0x11000000\0" \
+ "console=ttymxc3,115200\0" \
+ "ethprime=FEC0\0" \
+ "bootscr=boot.scr\0" \
+ "bootm_low=18000000\0" \
+ "video_hdmi=mxcfb0:dev=hdmi,1920x1080M-32@50,if=RGB32\0" \
+ "video_dvi=mxcfb0:dev=dvi,1280x800M-32@50,if=RGB32\0" \
+ "fdtfile=cm-fx6.dtb\0" \
+ "doboot=bootm ${loadaddr}\0" \
+ "loadfdt=false\0" \
+ "setboottypez=setenv kernel zImage-cm-fx6;" \
+ "setenv doboot bootz ${loadaddr} - ${fdtaddr};" \
+ "setenv loadfdt true;\0" \
+ "setboottypem=setenv kernel uImage-cm-fx6;" \
+ "setenv doboot bootm ${loadaddr};" \
+ "setenv loadfdt false;\0"\
+ "run_eboot=echo Starting EBOOT ...; "\
+ "mmc dev ${mmcdev} && " \
+ "mmc rescan && mmc read 10042000 a 400 && go 10042000\0" \
+ "mmcdev=2\0" \
+ "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
+ "loadmmcbootscript=load mmc ${mmcdev} ${loadaddr} ${bootscr}\0" \
+ "mmcbootscript=echo Running bootscript from mmc ...; "\
+ "source ${loadaddr}\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "root=${mmcroot} " \
+ "${video}\0" \
+ "mmcloadkernel=load mmc ${mmcdev} ${loadaddr} ${kernel}\0" \
+ "mmcloadfdt=load mmc ${mmcdev} ${fdtaddr} ${fdtfile}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "run doboot\0" \
+ "satadev=0\0" \
+ "sataroot=/dev/sda2 rw rootwait\0" \
+ "sataargs=setenv bootargs console=${console} " \
+ "root=${sataroot} " \
+ "${video}\0" \
+ "loadsatabootscript=load sata ${satadev} ${loadaddr} ${bootscr}\0" \
+ "satabootscript=echo Running bootscript from sata ...; " \
+ "source ${loadaddr}\0" \
+ "sataloadkernel=load sata ${satadev} ${loadaddr} ${kernel}\0" \
+ "sataloadfdt=load sata ${satadev} ${fdtaddr} ${fdtfile}\0" \
+ "sataboot=echo Booting from sata ...; "\
+ "run sataargs; " \
+ "run doboot\0" \
+ "nandroot=/dev/mtdblock4 rw\0" \
+ "nandrootfstype=ubifs\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "root=${nandroot} " \
+ "rootfstype=${nandrootfstype} " \
+ "${video}\0" \
+ "nandloadfdt=nand read ${fdtaddr} 780000 80000;\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} 0 780000; " \
+ "if ${loadfdt}; then " \
+ "run nandloadfdt;" \
+ "fi; " \
+ "run doboot\0" \
+ "boot=mmc dev ${mmcdev}; " \
+ "if mmc rescan; then " \
+ "if run loadmmcbootscript; then " \
+ "run mmcbootscript;" \
+ "else " \
+ "if run mmcloadkernel; then " \
+ "if ${loadfdt}; then " \
+ "run mmcloadfdt;" \
+ "fi;" \
+ "run mmcboot;" \
+ "fi;" \
+ "fi;" \
+ "fi;" \
+ "if sata init; then " \
+ "if run loadsatabootscript; then " \
+ "run satabootscript;" \
+ "else "\
+ "if run sataloadkernel; then " \
+ "if ${loadfdt}; then " \
+ "run sataloadfdt; " \
+ "fi;" \
+ "run sataboot;" \
+ "fi;" \
+ "fi;" \
+ "fi;" \
+ "run nandboot\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "run setboottypem; run boot"
+
+/* SPI */
+#define CONFIG_SPI
+#define CONFIG_MXC_SPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+#define CONFIG_SPI_FLASH_EON
+#define CONFIG_SPI_FLASH_GIGADEVICE
+#define CONFIG_SPI_FLASH_MACRONIX
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SPI_FLASH_WINBOND
+
+/* NAND */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_CMD_NAND
+#define CONFIG_SYS_NAND_BASE 0x40000000
+#define CONFIG_SYS_NAND_MAX_CHIPS 1
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_NAND_MXS
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+/* APBH DMA is required for NAND support */
+#define CONFIG_APBH_DMA
+#define CONFIG_APBH_DMA_BURST
+#define CONFIG_APBH_DMA_BURST8
+#endif
+
+/* Ethernet */
+#define CONFIG_FEC_MXC
+#define CONFIG_FEC_MXC_PHYADDR 0
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+#define CONFIG_MII
+#define CONFIG_ETHPRIME "FEC0"
+#define CONFIG_ARP_TIMEOUT 200UL
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_NET_RETRY_COUNT 5
+
+/* USB */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
+
+/* I2C */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_SYS_MXC_I2C3_SPEED 400000
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_BUS 2
+
+/* SATA */
+#define CONFIG_CMD_SATA
+#define CONFIG_SYS_SATA_MAX_DEVICE 1
+#define CONFIG_LIBATA
+#define CONFIG_LBA48
+#define CONFIG_DWC_AHSATA
+#define CONFIG_DWC_AHSATA_PORT_ID 0
+#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
+
+/* GPIO */
+#define CONFIG_MXC_GPIO
+
+/* Boot */
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+#define CONFIG_LOADADDR 0x10800000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20)
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SERIAL_TAG
+
+/* misc */
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_STACKSIZE (128 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (2 * 1024 * 1024)
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 800 /* 400 KB */
+#define CONFIG_OF_BOARD_SETUP
+
+/* SPL */
+#include "imx6_spl.h"
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x80 /* offset 64 kb */
+#define CONFIG_SYS_MONITOR_LEN (CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS / 2 * 1024)
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SYS_SPI_U_BOOT_OFFS (64 * 1024)
+#define CONFIG_SPL_SPI_LOAD
+
+#endif /* __CONFIG_CM_FX6_H */
/* I2C Configuration */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_BUS 0
/* SPL */
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds"
#define CONFIG_SYS_I2C_OMAP34XX
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_BUS 0
#define CONFIG_I2C_MULTI_BUS
/*
#define CONFIG_SYS_I2C_OMAP34XX
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_BUS 0
/* Enable SD/MMC CD and WP GPIOs */
#define OMAP_HSMMC_USE_GPIO
#include "tegra20-common.h"
-/* Enable FDT support */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra20-colibri_t20_iris
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra20 (Colibri) # "
#define CONFIG_TEGRA_BOARD_STRING "Toradex Colibri T20 on Iris"
#include "tegra30-common.h"
-#define CONFIG_DEFAULT_DEVICE_TREE tegra30-colibri
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
#define V_PROMPT "Colibri T30 # "
#define CONFIG_TEGRA_BOARD_STRING "Toradex Colibri T30"
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_LAST_STAGE_INIT
-#undef CONFIG_CMD_BOOTM
#endif /* CONFIG_TRAILBLAZER */
#define CONFIG_LMB
#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-#define CONFIG_DEFAULT_DEVICE_TREE link
#define CONFIG_BOOTSTAGE
#define CONFIG_BOOTSTAGE_REPORT
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SPL_SPI_BUS 0
-#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
#define CONFIG_SYS_SPI_U_BOOT_SIZE 0x30000
#endif
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SPL_SPI_BUS 0
-#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#include "tegra114-common.h"
-/* Enable fdt support for Dalmore. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra114-dalmore
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra114 (Dalmore) # "
#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Dalmore"
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SPL_SPI_FLASH_SUPPORT
-#define CONFIG_SPL_SPI_BUS 0
-#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x40000
#define CONFIG_SUPPORT_EMMC_BOOT
#define CONFIG_SPI_FLASH_SST
#define CONFIG_MXC_SPI
#define CONFIG_SF_DEFAULT_BUS 0
-#define CONFIG_SF_DEFAULT_CS (0 | (IMX_GPIO_NR(2, 30) << 8))
+#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#endif
#define CONFIG_BOARD_COMMON
#define CONFIG_SYS_GENERIC_BOARD
-/* Enable fdt support */
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
#define CONFIG_SYS_CACHELINE_SIZE 32
/* input clock of PLL: EXYNOS4 boards have 24MHz input clock */
#define CONFIG_ARCH_EARLY_INIT_R
#define CONFIG_EXYNOS_SPL
-/* Enable fdt support for Exynos5250 */
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* Allow tracing to be enabled */
#define CONFIG_TRACE
#define CONFIG_CMD_TRACE
#define CONFIG_SPI_FLASH_BAR
#define CONFIG_SPI_FLASH_WINBOND
#define CONFIG_SF_DEFAULT_BUS 0
- #define CONFIG_SF_DEFAULT_CS (0|(IMX_GPIO_NR(3, 19)<<8))
+ #define CONFIG_SF_DEFAULT_CS 0
/* GPIO 3-19 (21248) */
#define CONFIG_SF_DEFAULT_SPEED 30000000
#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
#define CONFIG_PCI
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_PCI_FIXUP_DEV
#define CONFIG_PCIE_IMX
#endif
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 38400, 115200 }
-#define CONFIG_CMD_IMPORTENV 1
#define CONFIG_CMD_LOADB
#define CONFIG_CMD_SOURCE
#define CONFIG_CMD_RUN
#include <linux/sizes.h>
#include "tegra20-common.h"
-/* Enable fdt support for Harmony. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra20-harmony
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra20 (Harmony) # "
#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Harmony"
#define CONFIG_BAUDRATE 115200
#define CONFIG_MISC_INIT_R /* needed for MAC address */
#define CONFIG_UART_CONSOLE 0
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
#undef CONFIG_SHOW_BOOT_PROGRESS
/* Enable this if bootretry required; currently it's disabled */
#include "tegra124-common.h"
-/* Enable fdt support for Jetson TK1. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra124-jetson-tk1
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra124 (Jetson TK1) # "
#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Jetson TK1"
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SPL_SPI_BUS 0
-#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_SPL_PAD_TO
#define CONFIG_SPL_FRAMEWORK
#undef CONFIG_BOOTM_RTEMS
#undef CONFIG_GZIP
#undef CONFIG_ZLIB
-#undef CONFIG_CMD_CRC32
/* USB configuration */
#define CONFIG_USB_MUSB_DSPS
#define CONFIG_DDR_SPD
#define SPD_EEPROM_ADDRESS 0x51
#define CONFIG_SYS_SPD_BUS_NUM 0
-#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
+#ifndef CONFIG_SYS_FSL_DDR4
#define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */
+#define CONFIG_SYS_DDR_RAW_TIMING
+#endif
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
#define CONFIG_GICV3
/* Link Definitions */
-#define CONFIG_SYS_TEXT_BASE 0x30000000
+#define CONFIG_SYS_TEXT_BASE 0x30001000
+#ifdef CONFIG_EMU
#define CONFIG_SYS_NO_FLASH
+#endif
#define CONFIG_SUPPORT_RAW_INITRD
#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
-/* SMP Definitions */
-#define CPU_RELEASE_ADDR CONFIG_SYS_INIT_SP_ADDR
-
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
+#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2
+
+/*
+ * SMP Definitinos
+ */
+#define CPU_RELEASE_ADDR secondary_boot_func
+
+#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
+#define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL
+/*
+ * DDR controller use 0 as the base address for binding.
+ * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
+ */
+#define CONFIG_SYS_DP_DDR_BASE_PHY 0
+#define CONFIG_DP_DDR_CTRL 2
+#define CONFIG_DP_DDR_NUM_CTRLS 1
+#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1
/* Generic Timer Definitions */
#define COUNTER_FREQUENCY 12000000 /* 12MHz */
#define CONFIG_SYS_NOR_FTIM3 0x04000000
#define CONFIG_SYS_IFC_CCR 0x01000000
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+#endif
+
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_MAX_ECCPOS 256
+#define CONFIG_SYS_NAND_MAX_OOBFREE 2
+#define CONFIG_SYS_NAND_BASE 0x520000000
+#define CONFIG_SYS_NAND_BASE_PHYS 0x20000000
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
+
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
+ | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
+#define CONFIG_ARCH_EARLY_INIT_R
/* Physical Memory Map */
/* fixme: these need to be checked against the board */
#define CONFIG_SYS_CLK_FREQ 133333333
-#define CONFIG_NR_DRAM_BANKS 2
+#define CONFIG_NR_DRAM_BANKS 3
#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_FSL_DDR_EMU /* Support emulator */
#define SPD_EEPROM_ADDRESS1 0x51
#define SPD_EEPROM_ADDRESS2 0x52
+#define SPD_EEPROM_ADDRESS3 0x53
#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
#define CONFIG_SYS_SPD_BUS_NUM 1 /* SPD on I2C bus 1 */
#define CONFIG_SMC91111
#define CONFIG_SMC91111_BASE (0x2210000)
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
+
#endif /* __LS2_SIMU_H */
#include "tegra20-common.h"
-/* Enable fdt support for Medcom-Wide. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra20-medcom-wide
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra20 (Medcom-Wide) # "
#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Medcom-Wide"
/* MicroBlaze CPU */
#define MICROBLAZE_V5 1
-/* Open Firmware DTS */
-#define CONFIG_OF_CONTROL 1
-#define CONFIG_OF_EMBED 1
-#define CONFIG_DEFAULT_DEVICE_TREE microblaze-generic
-
/* linear and spi flash memory */
#ifdef XILINX_FLASH_START
#define FLASH
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_SST
-#define CONFIG_SF_DEFAULT_CS (1 | 121 << 8)
+#define CONFIG_SF_DEFAULT_CS 1
#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
#define CONFIG_SF_DEFAULT_SPEED 25000000
-#define CONFIG_ENV_SPI_CS (1 | 121 << 8)
+#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_MAX_HZ 25000000
#define CONFIG_ENV_SPI_MODE (SPI_MODE_0)
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
+#define CONFIG_SYS_GENERIC_BOARD
+
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_OF_SEPARATE
-#define CONFIG_DEFAULT_DEVICE_TREE imx6q-sabreauto
-
#endif /* __MX6QSABREAUTO_CONFIG_H */
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_MXC_SPI
#define CONFIG_SF_DEFAULT_BUS 0
-#define CONFIG_SF_DEFAULT_CS (0 | (IMX_GPIO_NR(4, 9) << 8))
+#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#endif
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
+#define CONFIG_SYS_GENERIC_BOARD
+
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (3 * SZ_1M)
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_MXC_SPI
#define CONFIG_SF_DEFAULT_BUS 0
-#define CONFIG_SF_DEFAULT_CS (0 | (IMX_GPIO_NR(4, 11) << 8))
+#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#endif
#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS
+#define CONFIG_CMD_PCI
+#ifdef CONFIG_CMD_PCI
+#define CONFIG_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_PCIE_IMX
+#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(2, 1)
+#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(2, 0)
+#endif
+
/* FLASH and environment organization */
#define CONFIG_SYS_NO_FLASH
#define CONFIG_SPI_FLASH_SST
#define CONFIG_MXC_SPI
#define CONFIG_SF_DEFAULT_BUS 0
-#define CONFIG_SF_DEFAULT_CS (0|(IMX_GPIO_NR(3, 19)<<8))
+#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 25000000
#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
#endif
"mmcargs=setenv bootargs console=${console},${baudrate} " \
"root=${mmcroot}\0" \
"loadbootscript=" \
- "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
- "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "loaduimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
#define CONFIG_SYS_PROMPT "Odroid # " /* Monitor Command Prompt */
-#undef CONFIG_DEFAULT_DEVICE_TREE
-#define CONFIG_DEFAULT_DEVICE_TREE exynos4412-odroid
#define CONFIG_SYS_L2CACHE_OFF
#ifndef CONFIG_SYS_L2CACHE_OFF
#define CONFIG_SYS_PROMPT "ORIGEN # "
-#undef CONFIG_DEFAULT_DEVICE_TREE
-#define CONFIG_DEFAULT_DEVICE_TREE exynos4210-origen
/* High Level Configuration Options */
#define CONFIG_EXYNOS4210 1 /* which is a EXYNOS4210 SoC */
#include <linux/sizes.h>
#include "tegra20-common.h"
-/* Enable fdt support for Paz00. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra20-paz00
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra20 (Paz00) MOD # "
#define CONFIG_TEGRA_BOARD_STRING "Compal Paz00"
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SPL_SPI_BUS 0
-#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
#define CONFIG_SYS_SPI_U_BOOT_SIZE 0x40000
#endif
#include <configs/exynos5420.h>
-#undef CONFIG_DEFAULT_DEVICE_TREE
-#define CONFIG_DEFAULT_DEVICE_TREE exynos5420-peach-pit
/* select serial console configuration */
#define CONFIG_SERIAL3 /* use SERIAL 3 */
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __PH1_XXX_H
+#define __PH1_XXX_H
+
+/*
+ * Support Card Select
+ *
+ * CONFIG_PFC_MICRO_SUPPORT_CARD - Original Micro Support Card made by PFC.
+ * CONFIG_DCC_MICRO_SUPPORT_CARD - DCC version Micro Support Card.
+ * CPLD is re-programmed for ARIMA board compatibility.
+ * No define - No support card.
+ */
+
+#if 0
+#define CONFIG_PFC_MICRO_SUPPORT_CARD
+#else
+#define CONFIG_DCC_MICRO_SUPPORT_CARD
+#endif
+
+/*
+ * Serial Configuration
+ * SoC UART : enable CONFIG_UNIPHIER_SERIAL
+ * On-board UART: enable CONFIG_SYS_NS16550_SERIAL
+ */
+#if 1
+#define CONFIG_UNIPHIER_SERIAL
+#else
+#define CONFIG_SYS_NS16550_SERIAL
+#endif
+
+#define CONFIG_SYS_UNIPHIER_UART_CLK 36864000
+
+#define CONFIG_SMC911X
+
+#define CONFIG_DDR_NUM_CH0 1
+#define CONFIG_DDR_NUM_CH1 1
+
+#define CONFIG_DDR_FREQ 1600
+
+/*
+ * Memory Size & Mapping
+ */
+/* Physical start address of SDRAM */
+#define CONFIG_SDRAM0_BASE 0x80000000
+#define CONFIG_SDRAM0_SIZE 0x10000000
+#define CONFIG_SDRAM1_BASE 0x90000000
+#define CONFIG_SDRAM1_SIZE 0x10000000
+
+#define CONFIG_SPL_TEXT_BASE 0x40000
+
+#include "uniphier-common.h"
+
+#endif /* __PH1_XXX_H */
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __PH1_XXX_H
+#define __PH1_XXX_H
+
+/*
+ * Support Card Select
+ *
+ * CONFIG_PFC_MICRO_SUPPORT_CARD - Original Micro Support Card made by PFC.
+ * CONFIG_DCC_MICRO_SUPPORT_CARD - DCC version Micro Support Card.
+ * CPLD is re-programmed for ARIMA board compatibility.
+ * No define - No support card.
+ */
+
+#if 0
+#define CONFIG_PFC_MICRO_SUPPORT_CARD
+#else
+#define CONFIG_DCC_MICRO_SUPPORT_CARD
+#endif
+
+/*
+ * Serial Configuration
+ * SoC UART : enable CONFIG_UNIPHIER_SERIAL
+ * On-board UART: enable CONFIG_SYS_NS16550_SERIAL
+ */
+#if 1
+#define CONFIG_UNIPHIER_SERIAL
+#else
+#define CONFIG_SYS_NS16550_SERIAL
+#endif
+
+#define CONFIG_SYS_UNIPHIER_UART_CLK 73728000
+
+#define CONFIG_SMC911X
+
+#define CONFIG_DDR_NUM_CH0 2
+#define CONFIG_DDR_NUM_CH1 2
+
+#define CONFIG_DDR_FREQ 1600
+
+#define CONFIG_UNIPHIER_SMP
+
+/*
+ * Memory Size & Mapping
+ */
+/* Physical start address of SDRAM */
+#define CONFIG_SDRAM0_BASE 0x80000000
+#define CONFIG_SDRAM0_SIZE 0x20000000
+#define CONFIG_SDRAM1_BASE 0xa0000000
+#define CONFIG_SDRAM1_SIZE 0x20000000
+
+#define CONFIG_SPL_TEXT_BASE 0x100000
+
+#include "uniphier-common.h"
+
+#endif /* __PH1_XXX_H */
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __PH1_XXX_H
+#define __PH1_XXX_H
+
+/*
+ * Support Card Select
+ *
+ * CONFIG_PFC_MICRO_SUPPORT_CARD - Original Micro Support Card made by PFC.
+ * CONFIG_DCC_MICRO_SUPPORT_CARD - DCC version Micro Support Card.
+ * CPLD is re-programmed for ARIMA board compatibility.
+ * No define - No support card.
+ */
+
+#if 0
+#define CONFIG_PFC_MICRO_SUPPORT_CARD
+#else
+#define CONFIG_DCC_MICRO_SUPPORT_CARD
+#endif
+
+/*
+ * Serial Configuration
+ * SoC UART : enable CONFIG_UNIPHIER_SERIAL
+ * On-board UART: enable CONFIG_SYS_NS16550_SERIAL
+ */
+#if 1
+#define CONFIG_UNIPHIER_SERIAL
+#else
+#define CONFIG_SYS_NS16550_SERIAL
+#endif
+
+#define CONFIG_SYS_UNIPHIER_UART_CLK 80000000
+
+#define CONFIG_SMC911X
+
+#define CONFIG_DDR_NUM_CH0 1
+#define CONFIG_DDR_NUM_CH1 1
+
+#define CONFIG_DDR_FREQ 1333
+
+/* #define CONFIG_DDR_STANDARD */
+
+/*
+ * Memory Size & Mapping
+ */
+/* Physical start address of SDRAM */
+#define CONFIG_SDRAM0_BASE 0x80000000
+#define CONFIG_SDRAM0_SIZE 0x10000000
+#define CONFIG_SDRAM1_BASE 0x90000000
+#define CONFIG_SDRAM1_SIZE 0x10000000
+
+#define CONFIG_SPL_TEXT_BASE 0x40000
+
+#include "uniphier-common.h"
+
+#endif /* __PH1_XXX_H */
#include "tegra20-common.h"
-/* Enable fdt support for Plutux. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra20-plutux
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra20 (Plutux) # "
#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Plutux"
#define CONFIG_BOOTCOMMAND "run nandboot"
#define CONFIG_BOOTDELAY 2
#define CONFIG_LOADADDR 0x2000000
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
#define CONFIG_SYS_PROMPT "Universal # " /* Monitor Command Prompt */
-#undef CONFIG_DEFAULT_DEVICE_TREE
-#define CONFIG_DEFAULT_DEVICE_TREE exynos4210-universal_c210
#define CONFIG_TIZEN /* TIZEN lib */
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-/* No NOR flash */
+/* NOR flash */
+#define CONFIG_CMD_FLASH
+
+#ifdef CONFIG_CMD_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_PROTECTION
+#define CONFIG_SYS_FLASH_BASE 0x10000000
+#define CONFIG_SYS_MAX_FLASH_SECT 131
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#else
#define CONFIG_SYS_NO_FLASH
+#endif
/*
* Command line configuration.
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SPL_SPI_BUS 0
-#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8400
#endif
/* Number of bits in a C 'long' on this architecture */
#define CONFIG_SANDBOX_BITS_PER_LONG 64
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_HOSTFILE
#define CONFIG_OF_LIBFDT
#define CONFIG_LMB
#define CONFIG_FIT
#define CONFIG_FIT_SIGNATURE
#define CONFIG_RSA
#define CONFIG_CMD_FDT
-#define CONFIG_DEFAULT_DEVICE_TREE sandbox
#define CONFIG_ANDROID_BOOT_IMAGE
#define CONFIG_FS_FAT
#define CONFIG_ENV_SIZE 8192
#define CONFIG_ENV_IS_NOWHERE
-/* SPI */
+/* SPI - enable all SPI flash types for testing purposes */
#define CONFIG_SANDBOX_SPI
#define CONFIG_CMD_SF
#define CONFIG_CMD_SF_TEST
#define CONFIG_SPI_FLASH
#define CONFIG_OF_SPI
#define CONFIG_OF_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+#define CONFIG_SPI_FLASH_EON
+#define CONFIG_SPI_FLASH_GIGADEVICE
+#define CONFIG_SPI_FLASH_MACRONIX
#define CONFIG_SPI_FLASH_SANDBOX
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_SPI_FLASH_SST
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_SPI_FLASH_WINBOND
#include "tegra20-common.h"
-/* Enable fdt support for Seaboard. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra20-seaboard
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra20 (SeaBoard) # "
#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Seaboard"
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SPL_SPI_BUS 0
-#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds"
#include <configs/exynos5250-dt.h>
-#undef CONFIG_DEFAULT_DEVICE_TREE
-#define CONFIG_DEFAULT_DEVICE_TREE exynos5250-smdk5250
/* Enable FIT support and comparison */
#define CONFIG_FIT
#define CONFIG_SMDK5420 /* which is in a SMDK5420 */
-#undef CONFIG_DEFAULT_DEVICE_TREE
-#define CONFIG_DEFAULT_DEVICE_TREE exynos5420-smdk5420
/* select serial console configuration */
#define CONFIG_SERIAL3 /* use SERIAL 3 */
#include <configs/exynos5250-dt.h>
-#undef CONFIG_DEFAULT_DEVICE_TREE
-#define CONFIG_DEFAULT_DEVICE_TREE exynos5250-snow
/* Enable FIT support and comparison */
#define CONFIG_FIT
#define CONFIG_UART_CONSOLE 0
#define CONFIG_BOOTCOMMAND "run flashboot"
#define FLASHBOOT_ENV_SETTINGS "flashboot=bootm 0x20040000\0"
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
"flashboot=flread 20040000 1000000 300000;" \
"bootm 0x1000000\0"
#define CONFIG_BOARD_SIZE_LIMIT $$((384 * 1024))
-#define CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED
/*
* Pull in common ADI header for remaining command/environment setup
#include "tegra30-common.h"
-/* Enable fdt support for tec-ng. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra30-tec-ng
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra30 (TEC-NG) # "
#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Tamonten™ NG Evaluation Carrier"
#include "tegra20-common.h"
-/* Enable fdt support for TEC. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra20-tec
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra20 (TEC) # "
#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Tamonten Evaluation Carrier"
/* remove devicetree support */
#ifdef CONFIG_OF_CONTROL
-#undef CONFIG_OF_CONTROL
#endif
/* remove I2C support */
"vram=${vram} " \
"root=${mmcroot} " \
"rootfstype=${mmcrootfstype}\0" \
- "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
+ "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
"source ${loadaddr}\0" \
- "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} uEnv.txt\0" \
+ "loadbootenv=load mmc ${mmcdev} ${loadaddr} uEnv.txt\0" \
"importbootenv=echo Importing environment from mmc${mmcdev} ...; " \
"env import -t ${loadaddr} ${filesize}\0" \
"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
#define CONFIG_TRATS
-#undef CONFIG_DEFAULT_DEVICE_TREE
-#define CONFIG_DEFAULT_DEVICE_TREE exynos4210-trats
#define CONFIG_TIZEN /* TIZEN lib */
#define CONFIG_SYS_PROMPT "Trats2 # " /* Monitor Command Prompt */
-#undef CONFIG_DEFAULT_DEVICE_TREE
-#define CONFIG_DEFAULT_DEVICE_TREE exynos4412-trats2
#define CONFIG_TIZEN /* TIZEN lib */
#include <linux/sizes.h>
#include "tegra20-common.h"
-/* Enable fdt support for TrimSlice. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra20-trimslice
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra20 (TrimSlice) # "
#define CONFIG_TEGRA_BOARD_STRING "Compulab Trimslice"
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SPL_SPI_BUS 0
-#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
#undef CONFIG_ENV_IS_NOWHERE
#define CONFIG_ENV_IS_IN_SPI_FLASH
--- /dev/null
+/*
+ * Copyright (C) 2012-2014 Panasonic Corporation
+ * Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/* U-boot - Common settings for UniPhier Family */
+
+#ifndef __CONFIG_UNIPHIER_COMMON_H__
+#define __CONFIG_UNIPHIER_COMMON_H__
+
+#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD) && \
+ defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
+# error "Both CONFIG_PFC_MICRO_SUPPORT_CARD and CONFIG_DCC_MICRO_SUPPORT_CARD \
+are defined. Select only one of them."
+#endif
+
+/*
+ * Support card address map
+ */
+#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
+# define CONFIG_SUPPORT_CARD_BASE 0x03f00000
+# define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
+# define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00090000)
+# define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x000b0000)
+#endif
+
+#if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
+# define CONFIG_SUPPORT_CARD_BASE 0x08000000
+# define CONFIG_SUPPORT_CARD_ETHER_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00000000)
+# define CONFIG_SUPPORT_CARD_LED_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00401630)
+# define CONFIG_SUPPORT_CARD_UART_BASE (CONFIG_SUPPORT_CARD_BASE + 0x00200000)
+#endif
+
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_COM1 CONFIG_SUPPORT_CARD_UART_BASE
+#define CONFIG_SYS_NS16550_CLK 12288000
+#define CONFIG_SYS_NS16550_REG_SIZE -2
+
+#define CONFIG_SMC911X_BASE CONFIG_SUPPORT_CARD_ETHER_BASE
+#define CONFIG_SMC911X_32_BIT
+
+#define CONFIG_SYS_UNIPHIER_SERIAL_BASE0 0x54006800
+#define CONFIG_SYS_UNIPHIER_SERIAL_BASE1 0x54006900
+#define CONFIG_SYS_UNIPHIER_SERIAL_BASE2 0x54006a00
+#define CONFIG_SYS_UNIPHIER_SERIAL_BASE3 0x54006b00
+
+/*-----------------------------------------------------------------------
+ * MMU and Cache Setting
+ *----------------------------------------------------------------------*/
+
+/* Comment out the following to enable L1 cache */
+/* #define CONFIG_SYS_ICACHE_OFF */
+/* #define CONFIG_SYS_DCACHE_OFF */
+
+/* Comment out the following to enable L2 cache */
+#define CONFIG_UNIPHIER_L2CACHE_ON
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
+
+#define CONFIG_TIMESTAMP
+
+/* FLASH related */
+#define CONFIG_MTD_DEVICE
+
+/*
+ * uncomment the following to disable FLASH related code.
+ */
+/* #define CONFIG_SYS_NO_FLASH */
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+
+#define CONFIG_SYS_MAX_FLASH_SECT 256
+#define CONFIG_SYS_MONITOR_BASE 0
+#define CONFIG_SYS_FLASH_BASE 0
+
+/*
+ * flash_toggle does not work for out supoort card.
+ * We need to use flash_status_poll.
+ */
+#define CONFIG_SYS_CFI_FLASH_STATUS_POLL
+
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#if defined(CONFIG_PFC_MICRO_SUPPORT_CARD)
+# define CONFIG_SYS_MAX_FLASH_BANKS 1
+# define CONFIG_SYS_FLASH_BANKS_LIST {0x00000000}
+# define CONFIG_SYS_FLASH_BANKS_SIZES {0x02000000}
+#endif
+
+#if defined(CONFIG_DCC_MICRO_SUPPORT_CARD)
+# define CONFIG_SYS_MAX_FLASH_BANKS 1
+# define CONFIG_SYS_FLASH_BANKS_LIST {0x04000000}
+# define CONFIG_SYS_FLASH_BANKS_SIZES {0x04000000}
+#endif
+
+/* serial console configuration */
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_SYS_GENERIC_BOARD
+
+#if !defined(CONFIG_SPL_BUILD)
+#define CONFIG_USE_ARCH_MEMSET
+#define CONFIG_USE_ARCH_MEMCPY
+#endif
+
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+
+#define CONFIG_CMDLINE_EDITING /* add command line history */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
+
+#define CONFIG_CONS_INDEX 1
+
+/*
+ * For NAND booting the environment is embedded in the U-Boot image. Please take
+ * look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
+ */
+/* #define CONFIG_ENV_IS_IN_NAND */
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET 0x0
+/* #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) */
+
+/* Time clock 1MHz */
+#define CONFIG_SYS_TIMER_RATE 1000000
+
+/*
+ * By default, ARP timeout is 5 sec.
+ * The first ARP request does not seem to work.
+ * So we need to retry ARP request anyway.
+ * We want to shrink the interval until the second ARP request.
+ */
+#define CONFIG_ARP_TIMEOUT 500UL /* 0.5 msec */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_TIME
+#define CONFIG_CMD_NAND /* NAND flash suppport */
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_MAX_CHIPS 2
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+#define CONFIG_NAND_DENALI_ECC_SIZE 1024
+
+#define CONFIG_SYS_NAND_REGS_BASE 0x68100000
+#define CONFIG_SYS_NAND_DATA_BASE 0x68000000
+
+#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_DATA_BASE + 0x10)
+
+#define CONFIG_SYS_NAND_USE_FLASH_BBT
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
+
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01000000)
+
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT \
+ "Press SPACE to abort autoboot in %d seconds\n", bootdelay
+#define CONFIG_AUTOBOOT_DELAY_STR "d"
+#define CONFIG_AUTOBOOT_STOP_STR " "
+
+/*
+ * Network Configuration
+ */
+#define CONFIG_ETHADDR 00:21:83:24:00:00
+#define CONFIG_SERVERIP 192.168.11.1
+#define CONFIG_IPADDR 192.168.11.10
+#define CONFIG_GATEWAYIP 192.168.11.1
+#define CONFIG_NETMASK 255.255.255.0
+
+#define CONFIG_LOADADDR 0x84000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_BOOTFILE "fit.itb"
+
+#define CONFIG_CMDLINE_EDITING /* add command line history */
+
+#define CONFIG_BOOTCOMMAND "run $bootmode"
+
+#define CONFIG_ROOTPATH "/nfs/root/path"
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs $bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off;" \
+ "tftpboot; bootm;"
+
+#define CONFIG_BOOTARGS " user_debug=0x1f init=/sbin/init"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "image_offset=0x00080000\0" \
+ "image_size=0x00f00000\0" \
+ "verify=n\0" \
+ "autostart=yes\0" \
+ "norboot=run add_default_bootargs;" \
+ "bootm $image_offset\0" \
+ "nandboot=run add_default_bootargs;" \
+ "nand read $loadaddr $image_offset $image_size;" \
+ "bootm\0" \
+ "add_default_bootargs=setenv bootargs $bootargs" \
+ " console=ttyS0,$baudrate\0" \
+
+/* FIT support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
+
+/* Open Firmware flat tree */
+#define CONFIG_OF_LIBFDT
+
+#define CONFIG_HAVE_ARM_SECURE
+
+/* Memory Size & Mapping */
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SDRAM0_BASE
+
+#if CONFIG_SDRAM0_BASE + CONFIG_SDRAM0_SIZE >= CONFIG_SDRAM1_BASE
+/* Thre is no memory hole */
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE + CONFIG_SDRAM1_SIZE)
+#else
+#define CONFIG_NR_DRAM_BANKS 2
+#define CONFIG_SYS_SDRAM_SIZE (CONFIG_SDRAM0_SIZE)
+#endif
+
+#define CONFIG_SYS_TEXT_BASE 0x84000000
+
+#if defined(CONFIG_SPL_BUILD)
+#define CONFIG_BOARD_POSTCLK_INIT
+#else
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#endif
+
+#define CONFIG_SYS_SPL_MALLOC_START (0x0ff00000)
+#define CONFIG_SYS_SPL_MALLOC_SIZE (0x00004000)
+
+#define CONFIG_SYS_INIT_SP_ADDR (0x0ff08000)
+
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_NAND_SUPPORT
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT /* for mem_malloc_init */
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+
+#define CONFIG_SPL_BOARD_INIT
+
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x10000
+
+#endif /* __CONFIG_UNIPHIER_COMMON_H__ */
#undef CONFIG_CMD_BEDBUG
#undef CONFIG_CMD_CACHE
#undef CONFIG_CMD_CONSOLE
-#undef CONFIG_CMD_CRC32
#undef CONFIG_CMD_DHCP
#undef CONFIG_CMD_EEPROM
#undef CONFIG_CMD_EEPROM
#include "tegra124-common.h"
-/* Enable fdt support for Venice2. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra124-venice2
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra124 (Venice2) # "
#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Venice2"
#include <linux/sizes.h>
#include "tegra20-common.h"
-/* Enable fdt support for Ventana. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra20-ventana
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra20 (Ventana) # "
#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Ventana"
/* Flat Device Tree Definitions */
#define CONFIG_OF_LIBFDT
-#define CONFIG_DEFAULT_DEVICE_TREE vexpress64
/* SMP Spin Table Definitions */
#ifdef CONFIG_BASE_FVP
* Use gpio 4 pin 25 as chip select for SPI flash
* This corresponds to gpio 121
*/
-#define CONFIG_SF_DEFAULT_CS (1 | (121 << 8))
+#define CONFIG_SF_DEFAULT_CS 1
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#define CONFIG_SF_DEFAULT_SPEED 25000000
-#define CONFIG_ENV_SPI_CS (1 | (121 << 8))
+#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_MAX_HZ 25000000
#define CONFIG_ENV_SPI_MODE SPI_MODE_0
#include <linux/sizes.h>
#include "tegra20-common.h"
-/* Enable fdt support for Whistler. Flash the image in u-boot-dtb.bin */
-#define CONFIG_DEFAULT_DEVICE_TREE tegra20-whistler
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
-
/* High-level configuration options */
#define V_PROMPT "Tegra20 (Whistler) # "
#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Whistler"
#define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */
/* FDT support */
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
#define CONFIG_DISPLAY_BOARDINFO_LATE
/* RSA support */
#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
-#if defined(CONFIG_OF_CONTROL) && defined(CONFIG_OF_SEPARATE)
-# define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot-dtb.img"
-#else
-# define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
-#endif
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot-dtb.img"
#endif
/* Disable dcache for SPL just for sure */
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_DCACHE_OFF
#undef CONFIG_FPGA
-#undef CONFIG_OF_CONTROL
#endif
/* Address in RAM where the parameters must be copied by SPL. */
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SPL_SPI_FLASH_SUPPORT
-#define CONFIG_SPL_SPI_BUS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000
-#define CONFIG_SPL_SPI_CS 0
#endif
/* for booting directly linux */
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ZYNQ_SDHCI0
-#define CONFIG_DEFAULT_DEVICE_TREE zynq-microzed
#include <configs/zynq-common.h>
#define CONFIG_ZYNQ_I2C0
#define CONFIG_ZYNQ_EEPROM
#define CONFIG_ZYNQ_BOOT_FREEBSD
-#define CONFIG_DEFAULT_DEVICE_TREE zynq-zc702
#include <configs/zynq-common.h>
# define CONFIG_ZYNQ_GEM_PHY_ADDR0 7
# define CONFIG_ZYNQ_SDHCI0
# define CONFIG_ZYNQ_SPI
-# define CONFIG_DEFAULT_DEVICE_TREE zynq-zc770-xm010
#elif defined(CONFIG_ZC770_XM012)
# define CONFIG_ZYNQ_SERIAL_UART1
# undef CONFIG_SYS_NO_FLASH
-# define CONFIG_DEFAULT_DEVICE_TREE zynq-zc770-xm012
#elif defined(CONFIG_ZC770_XM013)
# define CONFIG_ZYNQ_SERIAL_UART0
# define CONFIG_ZYNQ_GEM1
# define CONFIG_ZYNQ_GEM_PHY_ADDR1 7
-# define CONFIG_DEFAULT_DEVICE_TREE zynq-zc770-xm013
#else
# define CONFIG_ZYNQ_SERIAL_UART0
#define CONFIG_ZYNQ_USB
#define CONFIG_ZYNQ_SDHCI0
#define CONFIG_ZYNQ_BOOT_FREEBSD
-#define CONFIG_DEFAULT_DEVICE_TREE zynq-zed
#include <configs/zynq-common.h>
--- /dev/null
+/*
+ * Copyright 2014 Broadcom Corporation.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+void fb_mmc_flash_write(const char *cmd, void *download_buffer,
+ unsigned int download_bytes, char *response);
return fdt_set_status_by_alias(fdt, alias, FDT_STATUS_FAIL, 0);
}
+/* Helper to read a big number; size is in cells (not bytes) */
+static inline u64 of_read_number(const fdt32_t *cell, int size)
+{
+ u64 r = 0;
+ while (size--)
+ r = (r << 32) | fdt32_to_cpu(*(cell++));
+ return r;
+}
+
+void of_bus_default_count_cells(void *blob, int parentoffset,
+ int *addrc, int *sizec);
+
#endif /* ifdef CONFIG_OF_LIBFDT */
#ifdef USE_HOSTCC
#include <common_timing_params.h>
+#ifndef CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
+/* All controllers are for main memory */
+#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS CONFIG_NUM_DDR_CONTROLLERS
+#endif
+
#ifdef CONFIG_SYS_FSL_DDR_LE
#define ddr_in32(a) in_le32(a)
#define ddr_out32(a, v) out_le32(a, v)
memctl_options_t memctl_opts[CONFIG_SYS_NUM_DDR_CTLRS];
common_timing_params_t common_timing_params[CONFIG_SYS_NUM_DDR_CTLRS];
fsl_ddr_cfg_regs_t fsl_ddr_config_reg[CONFIG_SYS_NUM_DDR_CTLRS];
+ unsigned int first_ctrl;
+ unsigned int num_ctrls;
+ unsigned long long mem_base;
+ unsigned int dimm_slots_per_ctrl;
+ int (*board_need_mem_reset)(void);
+ void (*board_mem_reset)(void);
+ void (*board_mem_de_reset)(void);
} fsl_ddr_info_t;
/* Compute steps */
unsigned long long
fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step,
unsigned int size_only);
-
const char *step_to_string(unsigned int step);
unsigned int compute_fsl_memctl_config_regs(const memctl_options_t *popts,
int fsl_ddr_interactive_env_var_exists(void);
unsigned long long fsl_ddr_interactive(fsl_ddr_info_t *pinfo, int var_is_set);
void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd,
- unsigned int ctrl_num);
+ unsigned int ctrl_num, unsigned int dimm_slots_per_ctrl);
int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]);
unsigned int check_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr);
#define CONFIG_FSL_SDRAM_TYPE SDRAM_TYPE_DDR2
#endif
#elif defined(CONFIG_SYS_FSL_DDR3)
-#define FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR (3) /* FIXME */
typedef ddr3_spd_eeprom_t generic_spd_eeprom_t;
#ifndef CONFIG_FSL_SDRAM_TYPE
#define CONFIG_FSL_SDRAM_TYPE SDRAM_TYPE_DDR3
unsigned int twot_en;
unsigned int threet_en;
unsigned int bstopre;
- unsigned int tcke_clock_pulse_width_ps; /* tCKE */
unsigned int tfaw_window_four_activates_ps; /* tFAW -- FOUR_ACT */
/* Rtt impedance */
unsigned int trwt; /* read-to-write turnaround */
} memctl_options_t;
-extern phys_size_t fsl_ddr_sdram(void);
-extern phys_size_t fsl_ddr_sdram_size(void);
+phys_size_t fsl_ddr_sdram(void);
+phys_size_t fsl_ddr_sdram_size(void);
+phys_size_t fsl_other_ddr_sdram(unsigned long long base,
+ unsigned int first_ctrl,
+ unsigned int num_ctrls,
+ unsigned int dimm_slots_per_ctrl,
+ int (*board_need_reset)(void),
+ void (*board_reset)(void),
+ void (*board_de_reset)(void));
extern int fsl_use_spd(void);
-extern void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
- unsigned int ctrl_num, int step);
+void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
+ unsigned int ctrl_num, int step);
u32 fsl_ddr_get_intl3r(void);
+void print_ddr_info(unsigned int start_ctrl);
static void __board_assert_mem_reset(void)
{
* together. Assuming _list and _entry are the list and entry names,
* then the corresponding input section name is
*
- * _u_boot_list + _2_ + @_list + _2_ + @_entry
+ * .u_boot_list_ + 2_ + @_list + _2_ + @_entry
*
* and the C variable name is
*
- * .u_boot_list_ + 2_ + @_list + _2_ + @_entry
+ * _u_boot_list + _2_ + @_list + _2_ + @_entry
*
* This ensures uniqueness for both input section and C variable name.
*
#endif
#define __deprecated __attribute__((deprecated))
+#ifndef __packed
#define __packed __attribute__((packed))
+#endif
+#ifndef __weak
#define __weak __attribute__((weak))
+#endif
/*
* it doesn't make sense on ARM (currently the only user of __naked) to trace
* would be.
* [...]
*/
+#ifndef __pure
#define __pure __attribute__((pure))
+#endif
+#ifndef __aligned
#define __aligned(x) __attribute__((aligned(x)))
+#endif
#define __printf(a, b) __attribute__((format(printf, a, b)))
#define __scanf(a, b) __attribute__((format(scanf, a, b)))
#define noinline __attribute__((noinline))
*/
#define uninitialized_var(x) x = x
+#ifndef __always_inline
#define __always_inline inline __attribute__((always_inline))
+#endif
extern int pci_find_cap(struct pci_controller *hose, pci_dev_t dev, int pos,
int cap);
+#ifdef CONFIG_PCI_FIXUP_DEV
+extern void board_pci_fixup_dev(struct pci_controller *hose, pci_dev_t dev,
+ unsigned short vendor,
+ unsigned short device,
+ unsigned short class);
+#endif
+
const char * pci_class_str(u8 class);
int pci_last_busno(void);
int sata_initialize(void);
int __sata_initialize(void);
+int sata_port_status(int dev, int port);
extern block_dev_desc_t sata_dev_desc[];
#define SPI_XFER_MMAP 0x08 /* Memory Mapped start */
#define SPI_XFER_MMAP_END 0x10 /* Memory Mapped End */
#define SPI_XFER_ONCE (SPI_XFER_BEGIN | SPI_XFER_END)
-#define SPI_XFER_U_PAGE (1 << 5)
+#define SPI_XFER_U_PAGE (1 << 5)
/* SPI TX operation modes */
-#define SPI_OPM_TX_QPP 1 << 0
+#define SPI_OPM_TX_QPP (1 << 0)
/* SPI RX operation modes */
-#define SPI_OPM_RX_AS 1 << 0
-#define SPI_OPM_RX_DOUT 1 << 1
-#define SPI_OPM_RX_DIO 1 << 2
-#define SPI_OPM_RX_QOF 1 << 3
-#define SPI_OPM_RX_QIOF 1 << 4
-#define SPI_OPM_RX_EXTN SPI_OPM_RX_AS | SPI_OPM_RX_DOUT | \
+#define SPI_OPM_RX_AS (1 << 0)
+#define SPI_OPM_RX_DOUT (1 << 1)
+#define SPI_OPM_RX_DIO (1 << 2)
+#define SPI_OPM_RX_QOF (1 << 3)
+#define SPI_OPM_RX_QIOF (1 << 4)
+#define SPI_OPM_RX_EXTN (SPI_OPM_RX_AS | SPI_OPM_RX_DOUT | \
SPI_OPM_RX_DIO | SPI_OPM_RX_QOF | \
- SPI_OPM_RX_QIOF
+ SPI_OPM_RX_QIOF)
-/* SPI bus connection options */
-#define SPI_CONN_DUAL_SHARED 1 << 0
-#define SPI_CONN_DUAL_SEPARATED 1 << 1
+/* SPI bus connection options - see enum spi_dual_flash */
+#define SPI_CONN_DUAL_SHARED (1 << 0)
+#define SPI_CONN_DUAL_SEPARATED (1 << 1)
/* Header byte that marks the start of the message */
#define SPI_PREAMBLE_END_BYTE 0xec
#include <linux/types.h>
#include <linux/compiler.h>
+#ifndef CONFIG_SF_DEFAULT_SPEED
+# define CONFIG_SF_DEFAULT_SPEED 1000000
+#endif
+#ifndef CONFIG_SF_DEFAULT_MODE
+# define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
+#endif
+#ifndef CONFIG_SF_DEFAULT_CS
+# define CONFIG_SF_DEFAULT_CS 0
+#endif
+#ifndef CONFIG_SF_DEFAULT_BUS
+# define CONFIG_SF_DEFAULT_BUS 0
+#endif
+
/* sf param flags */
#define SECT_4K 1 << 1
#define SECT_32K 1 << 2
--- /dev/null
+menu "Library routines"
+
+config CC_OPTIMIZE_LIBS_FOR_SPEED
+ bool "Optimize libraries for speed"
+ help
+ Enabling this option will pass "-O2" to gcc when compiling
+ under "lib" directory.
+
+ If unsure, say N.
+
+endmenu
--- /dev/null
+#
+# Network configuration
+#
+
+menuconfig NET
+ bool "Networking support"
+
+if NET
+
+endif # if NET
NetSetTimeout(DNS_TIMEOUT, DnsTimeout);
net_set_udp_handler(DnsHandler);
+ /* Clear a previous MAC address, the server IP might have changed. */
+ memset(NetServerEther, 0, sizeof(NetServerEther));
+
DnsSend();
}
| sed '/=/ {s/=/ /;q; } ; { s/$$/ 1/; }'; \
done; \
echo \#define CONFIG_BOARDDIR board/$(if $(VENDOR),$(VENDOR)/)$(BOARD);\
- echo \#include \<config_cmd_defaults.h\>; \
echo \#include \<config_defaults.h\>; \
echo \#include \<configs/$(CONFIG_SYS_CONFIG_NAME).h\>; \
echo \#include \<asm/config.h\>; \
# build a list of files to remove, usually relative to the current
# directory
-__clean-files := $(extra-y) $(always) \
- $(targets) $(clean-files) \
+__clean-files := $(extra-y) $(extra-m) $(extra-) \
+ $(always) $(targets) $(clean-files) \
$(host-progs) \
$(hostprogs-y) $(hostprogs-m) $(hostprogs-)
"please, no space before tabs\n" . $herevet) &&
$fix) {
while ($fixed[$linenr - 1] =~
- s/(^\+.*) {8,8}+\t/$1\t\t/) {}
+ s/(^\+.*) {8,8}\t/$1\t\t/) {}
while ($fixed[$linenr - 1] =~
s/(^\+.*) +\t/$1\t/) {}
}
defconfig_path=$srctree/configs/$1
tmp_defconfig_path=configs/.tmp_defconfig
+ if [ ! -r $defconfig_path ]; then
+ echo >&2 "***"
+ echo >&2 "*** Can't find default configuration \"confis/$1\"!"
+ echo >&2 "***"
+ exit 1
+ fi
+
mkdir -p arch configs
# defconfig for Normal:
# pick lines without prefixes and lines starting '+' prefix
IFS=$save_IFS
}
+# Some sanity checks before running "make <objdir>/<target>",
+# where <objdir> should be either "spl" or "tpl".
+# Doing "make spl/menuconfig" etc. on a non-SPL board makes no sense.
+# It should be allowed only when ".config" exists and "CONFIG_SPL" is enabled.
+#
+# Usage:
+# check_enabled_sumbimage <objdir>/<target> <objdir>
+check_enabled_subimage () {
+
+ case $2 in
+ spl|tpl) ;;
+ *)
+ echo >&2 "***"
+ echo >&2 "*** \"make $1\" is not supported."
+ echo >&2 "***"
+ exit 1
+ ;;
+ esac
+ test -r "$KCONFIG_CONFIG" && get_enabled_subimages | grep -q $2 || {
+ config=CONFIG_$(echo $2 | tr '[a-z]' '[A-Z]')
+
+ echo >&2 "***"
+ echo >&2 "*** Create \"$KCONFIG_CONFIG\" with \"$config\" enabled"
+ echo >&2 "*** before \"make $1\"."
+ echo >&2 "***"
+ exit 1
+ }
+}
+
# Usage:
# do_others <objdir>/<target>
# The field "<objdir>/" is typically empy, "spl/", "tpl/" for Normal, SPL, TPL,
objdir=
else
objdir=${1%/*}
+ check_enabled_subimage $1 $objdir
fi
run_make_config $target $objdir
--- /dev/null
+#!/bin/sh
+
+# Test for U-Boot cli including command repeat
+
+BASE="$(dirname $0)"
+. $BASE/common.sh
+
+run_test() {
+ ./${OUTPUT_DIR}/u-boot <<END
+setenv ctrlc_ignore y
+md 0
+
+reset
+END
+}
+check_results() {
+ echo "Check results"
+
+ grep -q 00000100 ${tmp} || fail "Command did not repeat"
+}
+
+echo "Test CLI repeat"
+echo
+tmp="$(tempfile)"
+build_uboot
+run_test >${tmp}
+check_results ${tmp}
+rm ${tmp}
+echo "Test passed"
--- /dev/null
+#!/bin/sh
+
+OUTPUT_DIR=sandbox
+
+fail() {
+ echo "Test failed: $1"
+ if [ -n ${tmp} ]; then
+ rm ${tmp}
+ fi
+ exit 1
+}
+
+build_uboot() {
+ echo "Build sandbox"
+ OPTS="O=${OUTPUT_DIR} $1"
+ NUM_CPUS=$(grep -c processor /proc/cpuinfo)
+ echo ${OPTS}
+ make ${OPTS} sandbox_config
+ make ${OPTS} -s -j${NUM_CPUS}
+}
# Simple test script for tracing with sandbox
-OUTPUT_DIR=sandbox
TRACE_OPT="FTRACE=1"
-fail() {
- echo "Test failed: $1"
- if [ -n ${tmp} ]; then
- rm ${tmp}
- fi
- exit 1
-}
-
-build_uboot() {
- echo "Build sandbox"
- OPTS="O=${OUTPUT_DIR} ${TRACE_OPT}"
- NUM_CPUS=$(grep -c processor /proc/cpuinfo)
- make ${OPTS} sandbox_config
- make ${OPTS} -s -j${NUM_CPUS}
-}
+BASE="$(dirname $0)/.."
+. $BASE/common.sh
run_trace() {
echo "Run trace"
./${OUTPUT_DIR}/u-boot <<END
- trace stats
- hash sha256 0 10000
- trace pause
- trace stats
- hash sha256 0 10000
- trace stats
- trace resume
- hash sha256 0 10000
- trace pause
- trace stats
- reset
+trace stats
+hash sha256 0 10000
+trace pause
+trace stats
+hash sha256 0 10000
+trace stats
+trace resume
+hash sha256 0 10000
+trace pause
+trace stats
+reset
END
}
echo "Simple trace test / sanity check using sandbox"
echo
tmp="$(tempfile)"
-build_uboot
+build_uboot "${TRACE_OPT}"
run_trace >${tmp}
check_results ${tmp}
rm ${tmp}
Print(GetActionSummary(options.summary, commits, board_selected,
options))
+ # We can't show function sizes without board details at present
+ if options.show_bloat:
+ options.show_detail = True
builder.SetDisplayOptions(options.show_errors, options.show_sizes,
options.show_detail, options.show_bloat,
options.list_error_boards)
if options.summary:
- # We can't show function sizes without board details at present
- if options.show_bloat:
- options.show_detail = True
builder.ShowSummary(commits, board_selected)
else:
fail, warned = builder.BuildBoards(commits, board_selected,
#
-# SPDX-License-Identifier: GPL-2.0+
+# SPDX-License-Identifier: ISC
#
# Author: Ulf Magnusson
# https://github.com/ulfalizer/Kconfiglib
endif
always := fw_printenv
-hostprogs-y := fw_printenv_unstripped
+hostprogs-y := fw_printenv
-fw_printenv_unstripped-objs := fw_env.o fw_env_main.o \
+fw_printenv-objs := fw_env.o fw_env_main.o \
crc32.o ctype.o linux_string.o \
env_attr.o env_flags.o aes.o
-quiet_cmd_strip = STRIP $@
- cmd_strip = $(STRIP) -o $@ $<
+quiet_cmd_crosstools_strip = STRIP $^
+ cmd_crosstools_strip = $(STRIP) $^; touch $@
-$(obj)/fw_printenv: $(obj)/fw_printenv_unstripped FORCE
- $(call if_changed,strip)
+$(obj)/.strip: $(obj)/fw_printenv
+ $(call cmd,crosstools_strip)
+
+always += .strip
maintainers = []
status = '-'
for line in open(file):
+ # Check also commented maintainers
+ if line[:3] == '#M:':
+ line = line[1:]
tag, rest = line[:2], line[2:].strip()
if tag == 'M:':
maintainers.append(rest)
/* Parse dcd configuration file */
dcd_len = parse_cfg_file(imxhdr, params->imagename);
+ if (imximage_version == IMXIMAGE_V2) {
+ if (imximage_init_loadsize < imximage_ivt_offset +
+ sizeof(imx_header_v2_t))
+ imximage_init_loadsize = imximage_ivt_offset +
+ sizeof(imx_header_v2_t);
+ }
+
/* Set the imx header */
(*set_imx_hdr)(imxhdr, dcd_len, params->ep, imximage_ivt_offset);
#ifndef _IMXIMAGE_H_
#define _IMXIMAGE_H_
-#define MAX_HW_CFG_SIZE_V2 121 /* Max number of registers imx can set for v2 */
+#define MAX_HW_CFG_SIZE_V2 220 /* Max number of registers imx can set for v2 */
#define MAX_HW_CFG_SIZE_V1 60 /* Max number of registers imx can set for v1 */
#define APP_CODE_BARKER 0xB1
#define DCD_BARKER 0xB17219E9
in one of your commits, the series will be sent there.
-In Linux this will also call get_maintainer.pl on each of your
-patches automatically.
+In Linux and U-Boot this will also call get_maintainer.pl on each of your
+patches automatically (unless you use -m to disable this).
How to use this tool
parser.add_option('-i', '--ignore-errors', action='store_true',
dest='ignore_errors', default=False,
help='Send patches email even if patch errors are found')
+parser.add_option('-m', '--no-maintainers', action='store_false',
+ dest='add_maintainers', default=True,
+ help="Don't cc the file maintainers automatically")
parser.add_option('-n', '--dry-run', action='store_true', dest='dry_run',
default=False, help="Do a dry run (create but don't email patches)")
parser.add_option('-p', '--project', default=project.DetectProject(),
ok = True
cc_file = series.MakeCcFile(options.process_tags, cover_fname,
- not options.ignore_bad_tags)
+ not options.ignore_bad_tags,
+ options.add_maintainers)
# Email the patches out (giving the user time to check / cancel)
cmd = ''
str = 'Change log exists, but no version is set'
print col.Color(col.RED, str)
- def MakeCcFile(self, process_tags, cover_fname, raise_on_error):
+ def MakeCcFile(self, process_tags, cover_fname, raise_on_error,
+ add_maintainers):
"""Make a cc file for us to use for per-commit Cc automation
Also stores in self._generated_cc to make ShowActions() faster.
cover_fname: If non-None the name of the cover letter.
raise_on_error: True to raise an error when an alias fails to match,
False to just print a message.
+ add_maintainers: Call the get_maintainers to CC maintainers
Return:
Filename of temp file created
"""
raise_on_error=raise_on_error)
list += gitutil.BuildEmailList(commit.cc_list,
raise_on_error=raise_on_error)
- list += get_maintainer.GetMaintainer(commit.patch)
+ if add_maintainers:
+ list += get_maintainer.GetMaintainer(commit.patch)
all_ccs += list
print >>fd, commit.patch, ', '.join(list)
self._generated_cc[commit.patch] = list
+++ /dev/null
-#! /usr/bin/python
-########################################################################
-#
-# reorder and reformat a file in columns
-#
-# this utility takes lines from its standard input and reproduces them,
-# partially reordered and reformatted, on its standard output.
-#
-# It has the same effect as a 'sort | column -t', with the exception
-# that empty lines, as well as lines which start with a '#' sign, are
-# not affected, i.e. they keep their position and formatting, and act
-# as separators, i.e. the parts before and after them are each sorted
-# separately (but overall field widths are computed across the whole
-# input).
-#
-# Options:
-# -i:
-# --ignore-case:
-# Do not consider case when sorting.
-# -d:
-# --default:
-# What to chage empty fields to.
-# -s <N>:
-# --split=<N>:
-# Treat only the first N whitespace sequences as separators.
-# line content after the Nth separator will count as only one
-# field even if it contains whitespace.
-# Example : '-s 2' causes input 'a b c d e' to be split into
-# three fields, 'a', 'b', and 'c d e'.
-#
-# boards.cfg requires -ids 6.
-#
-########################################################################
-
-import sys, getopt, locale
-
-# ensure we sort using the C locale.
-
-locale.setlocale(locale.LC_ALL, 'C')
-
-# check options
-
-maxsplit = 0
-ignore_case = 0
-default_field =''
-
-try:
- opts, args = getopt.getopt(sys.argv[1:], "id:s:",
- ["ignore-case","default","split="])
-except getopt.GetoptError as err:
- print str(err) # will print something like "option -a not recognized"
- sys.exit(2)
-
-for o, a in opts:
- if o in ("-s", "--split"):
- maxsplit = eval(a)
- elif o in ("-i", "--ignore-case"):
- ignore_case = 1
- elif o in ("-d", "--default"):
- default_field = a
- else:
- assert False, "unhandled option"
-
-# collect all lines from standard input and, for the ones which must be
-# reformatted and sorted, count their fields and compute each field's
-# maximum size
-
-input_lines = []
-field_width = []
-
-for line in sys.stdin:
- # remove final end of line
- input_line = line.strip('\n')
- if (len(input_line)>0) and (input_line[0] != '#'):
- # sortable line: split into fields
- fields = input_line.split(None,maxsplit)
- # if there are new fields, top up field_widths
- for f in range(len(field_width), len(fields)):
- field_width.append(0)
- # compute the maximum witdh of each field
- for f in range(len(fields)):
- field_width[f] = max(field_width[f],len(fields[f]))
- # collect the line for next stage
- input_lines.append(input_line)
-
-# run through collected input lines, collect the ones which must be
-# reformatted and sorted, and whenever a non-reformattable, non-sortable
-# line is met, sort the collected lines before it and append them to the
-# output lines, then add the non-sortable line too.
-
-output_lines = []
-sortable_lines = []
-for input_line in input_lines:
- if (len(input_line)>0) and (input_line[0] != '#'):
- # this line should be reformatted and sorted
- input_fields = input_line.split(None,maxsplit)
- output_fields = [];
- # reformat each field to this field's column width
- for f in range(len(input_fields)):
- output_field = input_fields[f];
- output_fields.append(output_field.ljust(field_width[f]))
- # any missing field is set to default if it exists
- if default_field != '':
- for f in range(len(input_fields),len(field_width)):
- output_fields.append(default_field.ljust(field_width[f]))
- # join fields using two spaces, like column -t would
- output_line = ' '.join(output_fields);
- # collect line for later
- sortable_lines.append(output_line)
- else:
- # this line is non-sortable
- # sort collected sortable lines
- if ignore_case!=0:
- sortable_lines.sort(key=lambda x: str.lower(locale.strxfrm(x)))
- else:
- sortable_lines.sort(key=lambda x: locale.strxfrm(x))
- # append sortable lines to the final output
- output_lines.extend(sortable_lines)
- sortable_lines = []
- # append non-sortable line to the final output
- output_lines.append(input_line)
-# maybe we had sortable lines pending, so append them to the final output
-if ignore_case!=0:
- sortable_lines.sort(key=lambda x: str.lower(locale.strxfrm(x)))
-else:
- sortable_lines.sort(key=lambda x: locale.strxfrm(x))
-output_lines.extend(sortable_lines)
-
-# run through output lines and print them, except rightmost whitespace
-
-for output_line in output_lines:
- print output_line.rstrip()
projects / karo-tx-uboot.git / commitdiff