IrSR_RCVEIR_UART_MODE | \
IrSR_XMITIR_IR_MODE)
-/*
- * I2C registers
- */
-#define IBMR 0x40301680 /* I2C Bus Monitor Register - IBMR */
-#define IDBR 0x40301688 /* I2C Data Buffer Register - IDBR */
-#define ICR 0x40301690 /* I2C Control Register - ICR */
-#define ISR 0x40301698 /* I2C Status Register - ISR */
-#define ISAR 0x403016A0 /* I2C Slave Address Register - ISAR */
-
-#ifdef CONFIG_CPU_MONAHANS
-#define PWRIBMR 0x40f500C0 /* Power I2C Bus Monitor Register-IBMR */
-#define PWRIDBR 0x40f500C4 /* Power I2C Data Buffer Register-IDBR */
-#define PWRICR 0x40f500C8 /* Power I2C Control Register - ICR */
-#define PWRISR 0x40f500CC /* Power I2C Status Register - ISR */
-#define PWRISAR 0x40f500D0 /* Power I2C Slave Address Register-ISAR */
-#else
-#define PWRIBMR 0x40f00180 /* Power I2C Bus Monitor Register-IBMR */
-#define PWRIDBR 0x40f00188 /* Power I2C Data Buffer Register-IDBR */
-#define PWRICR 0x40f00190 /* Power I2C Control Register - ICR */
-#define PWRISR 0x40f00198 /* Power I2C Status Register - ISR */
-#define PWRISAR 0x40f001A0 /* Power I2C Slave Address Register-ISAR */
-#endif
-
-/* ----- Control register bits ---------------------------------------- */
-
-#define ICR_START 0x1 /* start bit */
-#define ICR_STOP 0x2 /* stop bit */
-#define ICR_ACKNAK 0x4 /* send ACK(0) or NAK(1) */
-#define ICR_TB 0x8 /* transfer byte bit */
-#define ICR_MA 0x10 /* master abort */
-#define ICR_SCLE 0x20 /* master clock enable, mona SCLEA */
-#define ICR_IUE 0x40 /* unit enable */
-#define ICR_GCD 0x80 /* general call disable */
-#define ICR_ITEIE 0x100 /* enable tx interrupts */
-#define ICR_IRFIE 0x200 /* enable rx interrupts, mona: DRFIE */
-#define ICR_BEIE 0x400 /* enable bus error ints */
-#define ICR_SSDIE 0x800 /* slave STOP detected int enable */
-#define ICR_ALDIE 0x1000 /* enable arbitration interrupt */
-#define ICR_SADIE 0x2000 /* slave address detected int enable */
-#define ICR_UR 0x4000 /* unit reset */
-#define ICR_FM 0x8000 /* Fast Mode */
-
-/* ----- Status register bits ----------------------------------------- */
-
-#define ISR_RWM 0x1 /* read/write mode */
-#define ISR_ACKNAK 0x2 /* ack/nak status */
-#define ISR_UB 0x4 /* unit busy */
-#define ISR_IBB 0x8 /* bus busy */
-#define ISR_SSD 0x10 /* slave stop detected */
-#define ISR_ALD 0x20 /* arbitration loss detected */
-#define ISR_ITE 0x40 /* tx buffer empty */
-#define ISR_IRF 0x80 /* rx buffer full */
-#define ISR_GCAD 0x100 /* general call address detected */
-#define ISR_SAD 0x200 /* slave address detected */
-#define ISR_BED 0x400 /* bus error no ACK/NAK */
-
/*
* Serial Audio Controller
*/
* (C) Copyright 2003 Pengutronix e.K.
* Robert Schwebel <r.schwebel@pengutronix.de>
*
+ * (C) Copyright 2011 Marvell Inc.
+ * Lei Wen <leiwen@marvell.com>
+ *
* See file CREDITS for list of people who contributed to this
* project.
*
#include <asm/io.h>
#ifdef CONFIG_HARD_I2C
-
-/*
- * - CONFIG_SYS_I2C_SPEED
- * - I2C_PXA_SLAVE_ADDR
- */
-
-#include <asm/arch/hardware.h>
-#include <asm/arch/pxa-regs.h>
#include <i2c.h>
-
-#if (CONFIG_SYS_I2C_SPEED == 400000)
-#define I2C_ICR_INIT (ICR_FM | ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD \
- | ICR_SCLE)
-#else
-#define I2C_ICR_INIT (ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD | ICR_SCLE)
-#endif
-
-#define I2C_ISR_INIT 0x7FF
+#include "mv_i2c.h"
#ifdef DEBUG_I2C
#define PRINTD(x) printf x
#define PRINTD(x)
#endif
-/* Shall the current transfer have a start/stop condition? */
-#define I2C_COND_NORMAL 0
-#define I2C_COND_START 1
-#define I2C_COND_STOP 2
-
-/* Shall the current transfer be ack/nacked or being waited for it? */
-#define I2C_ACKNAK_WAITACK 1
-#define I2C_ACKNAK_SENDACK 2
-#define I2C_ACKNAK_SENDNAK 4
-
-/* Specify who shall transfer the data (master or slave) */
-#define I2C_READ 0
-#define I2C_WRITE 1
-
/* All transfers are described by this data structure */
struct i2c_msg {
u8 condition;
u8 data;
};
+struct mv_i2c {
+ u32 ibmr;
+ u32 pad0;
+ u32 idbr;
+ u32 pad1;
+ u32 icr;
+ u32 pad2;
+ u32 isr;
+ u32 pad3;
+ u32 isar;
+};
+
+static struct mv_i2c *base = (struct mv_i2c *)CONFIG_MV_I2C_REG;
+
/*
- * i2c_pxa_reset: - reset the host controller
+ * i2c_reset: - reset the host controller
*
*/
static void i2c_reset(void)
{
- writel(readl(ICR) & ~ICR_IUE, ICR); /* disable unit */
- writel(readl(ICR) | ICR_UR, ICR); /* reset the unit */
+ writel(readl(&base->icr) & ~ICR_IUE, &base->icr); /* disable unit */
+ writel(readl(&base->icr) | ICR_UR, &base->icr); /* reset the unit */
udelay(100);
- writel(readl(ICR) & ~ICR_IUE, ICR); /* disable unit */
-#ifdef CONFIG_CPU_MONAHANS
- /* | CKENB_1_PWM1 | CKENB_0_PWM0); */
- writel(readl(CKENB) | (CKENB_4_I2C), CKENB);
-#else /* CONFIG_CPU_MONAHANS */
- /* set the global I2C clock on */
- writel(readl(CKEN) | CKEN14_I2C, CKEN);
-#endif
- writel(I2C_PXA_SLAVE_ADDR, ISAR); /* set our slave address */
- writel(I2C_ICR_INIT, ICR); /* set control reg values */
- writel(I2C_ISR_INIT, ISR); /* set clear interrupt bits */
- writel(readl(ICR) | ICR_IUE, ICR); /* enable unit */
+ writel(readl(&base->icr) & ~ICR_IUE, &base->icr); /* disable unit */
+
+ i2c_clk_enable();
+
+ writel(CONFIG_SYS_I2C_SLAVE, &base->isar); /* set our slave address */
+ writel(I2C_ICR_INIT, &base->icr); /* set control reg values */
+ writel(I2C_ISR_INIT, &base->isr); /* set clear interrupt bits */
+ writel(readl(&base->icr) | ICR_IUE, &base->icr); /* enable unit */
udelay(100);
}
static int i2c_isr_set_cleared(unsigned long set_mask,
unsigned long cleared_mask)
{
- int timeout = 1000;
+ int timeout = 1000, isr;
- while (((ISR & set_mask) != set_mask) || ((ISR & cleared_mask) != 0)) {
+ do {
+ isr = readl(&base->isr);
udelay(10);
if (timeout-- < 0)
return 0;
- }
+ } while (((isr & set_mask) != set_mask)
+ || ((isr & cleared_mask) != 0));
return 1;
}
goto transfer_error_bus_busy;
/* start transmission */
- writel(readl(ICR) & ~ICR_START, ICR);
- writel(readl(ICR) & ~ICR_STOP, ICR);
- writel(msg->data, IDBR);
+ writel(readl(&base->icr) & ~ICR_START, &base->icr);
+ writel(readl(&base->icr) & ~ICR_STOP, &base->icr);
+ writel(msg->data, &base->idbr);
if (msg->condition == I2C_COND_START)
- writel(readl(ICR) | ICR_START, ICR);
+ writel(readl(&base->icr) | ICR_START, &base->icr);
if (msg->condition == I2C_COND_STOP)
- writel(readl(ICR) | ICR_STOP, ICR);
+ writel(readl(&base->icr) | ICR_STOP, &base->icr);
if (msg->acknack == I2C_ACKNAK_SENDNAK)
- writel(readl(ICR) | ICR_ACKNAK, ICR);
+ writel(readl(&base->icr) | ICR_ACKNAK, &base->icr);
if (msg->acknack == I2C_ACKNAK_SENDACK)
- writel(readl(ICR) & ~ICR_ACKNAK, ICR);
- writel(readl(ICR) & ~ICR_ALDIE, ICR);
- writel(readl(ICR) | ICR_TB, ICR);
+ writel(readl(&base->icr) & ~ICR_ACKNAK, &base->icr);
+ writel(readl(&base->icr) & ~ICR_ALDIE, &base->icr);
+ writel(readl(&base->icr) | ICR_TB, &base->icr);
/* transmit register empty? */
if (!i2c_isr_set_cleared(ISR_ITE, 0))
goto transfer_error_transmit_timeout;
/* clear 'transmit empty' state */
- writel(readl(ISR) | ISR_ITE, ISR);
+ writel(readl(&base->isr) | ISR_ITE, &base->isr);
/* wait for ACK from slave */
if (msg->acknack == I2C_ACKNAK_WAITACK)
goto transfer_error_bus_busy;
/* start receive */
- writel(readl(ICR) & ~ICR_START, ICR);
- writel(readl(ICR) & ~ICR_STOP, ICR);
+ writel(readl(&base->icr) & ~ICR_START, &base->icr);
+ writel(readl(&base->icr) & ~ICR_STOP, &base->icr);
if (msg->condition == I2C_COND_START)
- writel(readl(ICR) | ICR_START, ICR);
+ writel(readl(&base->icr) | ICR_START, &base->icr);
if (msg->condition == I2C_COND_STOP)
- writel(readl(ICR) | ICR_STOP, ICR);
+ writel(readl(&base->icr) | ICR_STOP, &base->icr);
if (msg->acknack == I2C_ACKNAK_SENDNAK)
- writel(readl(ICR) | ICR_ACKNAK, ICR);
+ writel(readl(&base->icr) | ICR_ACKNAK, &base->icr);
if (msg->acknack == I2C_ACKNAK_SENDACK)
- writel(readl(ICR) & ~ICR_ACKNAK, ICR);
- writel(readl(ICR) & ~ICR_ALDIE, ICR);
- writel(readl(ICR) | ICR_TB, ICR);
+ writel(readl(&base->icr) & ~ICR_ACKNAK, &base->icr);
+ writel(readl(&base->icr) & ~ICR_ALDIE, &base->icr);
+ writel(readl(&base->icr) | ICR_TB, &base->icr);
/* receive register full? */
if (!i2c_isr_set_cleared(ISR_IRF, 0))
goto transfer_error_receive_timeout;
- msg->data = readl(IDBR);
+ msg->data = readl(&base->idbr);
/* clear 'receive empty' state */
- writel(readl(ISR) | ISR_IRF, ISR);
-
+ writel(readl(&base->isr) | ISR_IRF, &base->isr);
break;
default:
goto transfer_error_illegal_param;
void i2c_init(int speed, int slaveaddr)
{
#ifdef CONFIG_SYS_I2C_INIT_BOARD
- /* call board specific i2c bus reset routine before accessing the */
- /* environment, which might be in a chip on that bus. For details */
- /* about this problem see doc/I2C_Edge_Conditions. */
+ u32 icr;
+ /*
+ * call board specific i2c bus reset routine before accessing the
+ * environment, which might be in a chip on that bus. For details
+ * about this problem see doc/I2C_Edge_Conditions.
+ *
+ * disable I2C controller first, otherwhise it thinks we want to
+ * talk to the slave port...
+ */
+ icr = readl(&base->icr);
+ writel(readl(&base->icr) & ~(ICR_SCLE | ICR_IUE), &base->icr);
+
i2c_init_board();
+
+ writel(icr, &base->icr);
#endif
}
--- /dev/null
+/*
+ * (C) Copyright 2011
+ * Marvell Inc, <www.marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _MV_I2C_H_
+#define _MV_I2C_H_
+extern void i2c_clk_enable(void);
+
+/* Shall the current transfer have a start/stop condition? */
+#define I2C_COND_NORMAL 0
+#define I2C_COND_START 1
+#define I2C_COND_STOP 2
+
+/* Shall the current transfer be ack/nacked or being waited for it? */
+#define I2C_ACKNAK_WAITACK 1
+#define I2C_ACKNAK_SENDACK 2
+#define I2C_ACKNAK_SENDNAK 4
+
+/* Specify who shall transfer the data (master or slave) */
+#define I2C_READ 0
+#define I2C_WRITE 1
+
+#if (CONFIG_SYS_I2C_SPEED == 400000)
+#define I2C_ICR_INIT (ICR_FM | ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD \
+ | ICR_SCLE)
+#else
+#define I2C_ICR_INIT (ICR_BEIE | ICR_IRFIE | ICR_ITEIE | ICR_GCD | ICR_SCLE)
+#endif
+
+#define I2C_ISR_INIT 0x7FF
+/* ----- Control register bits ---------------------------------------- */
+
+#define ICR_START 0x1 /* start bit */
+#define ICR_STOP 0x2 /* stop bit */
+#define ICR_ACKNAK 0x4 /* send ACK(0) or NAK(1) */
+#define ICR_TB 0x8 /* transfer byte bit */
+#define ICR_MA 0x10 /* master abort */
+#define ICR_SCLE 0x20 /* master clock enable, mona SCLEA */
+#define ICR_IUE 0x40 /* unit enable */
+#define ICR_GCD 0x80 /* general call disable */
+#define ICR_ITEIE 0x100 /* enable tx interrupts */
+#define ICR_IRFIE 0x200 /* enable rx interrupts, mona: DRFIE */
+#define ICR_BEIE 0x400 /* enable bus error ints */
+#define ICR_SSDIE 0x800 /* slave STOP detected int enable */
+#define ICR_ALDIE 0x1000 /* enable arbitration interrupt */
+#define ICR_SADIE 0x2000 /* slave address detected int enable */
+#define ICR_UR 0x4000 /* unit reset */
+#define ICR_FM 0x8000 /* Fast Mode */
+
+/* ----- Status register bits ----------------------------------------- */
+
+#define ISR_RWM 0x1 /* read/write mode */
+#define ISR_ACKNAK 0x2 /* ack/nak status */
+#define ISR_UB 0x4 /* unit busy */
+#define ISR_IBB 0x8 /* bus busy */
+#define ISR_SSD 0x10 /* slave stop detected */
+#define ISR_ALD 0x20 /* arbitration loss detected */
+#define ISR_ITE 0x40 /* tx buffer empty */
+#define ISR_IRF 0x80 /* rx buffer full */
+#define ISR_GCAD 0x100 /* general call address detected */
+#define ISR_SAD 0x200 /* slave address detected */
+#define ISR_BED 0x400 /* bus error no ACK/NAK */
+
+#endif
projects / karo-tx-uboot.git / commitdiff