N: TsiChung Liew
E: Tsi-Chung.Liew@freescale.com
-D: Support for ColdFire MCF523x, MCF532x, MCF5445x
+D: Support for ColdFire MCF523x, MCF532x, MCF5445x, MCF547x_8x
W: www.freescale.com
N: Leif Lindholm
M5329EVB mcf532x
M5373EVB mcf532x
M54455EVB mcf5445x
+ M5475EVB mcf547x_8x
+ M5485EVB mcf547x_8x
Hayden Fraser <Hayden.Fraser@freescale.com>
M5329AFEE \
M5373EVB \
M54455EVB \
+ M5475AFE \
+ M5485AFE \
r5200 \
TASREG \
"
LIBS += disk/libdisk.a
LIBS += drivers/bios_emulator/libatibiosemu.a
LIBS += drivers/block/libblock.a
+LIBS += drivers/dma/libdma.a
LIBS += drivers/hwmon/libhwmon.a
LIBS += drivers/i2c/libi2c.a
LIBS += drivers/input/libinput.a
$(XECHO) "... with $${FREQ}Hz input clock"
@$(MKCONFIG) -a M54455EVB m68k mcf5445x m54455evb freescale
+M5475AFE_config \
+M5475BFE_config \
+M5475CFE_config \
+M5475DFE_config \
+M5475EFE_config \
+M5475FFE_config \
+M5475GFE_config : unconfig
+ @case "$@" in \
+ M5475AFE_config) BOOT=2;CODE=0;VID=0;USB=0;RAM=64;RAM1=0;; \
+ M5475BFE_config) BOOT=2;CODE=16;VID=0;USB=0;RAM=64;RAM1=0;; \
+ M5475CFE_config) BOOT=2;CODE=16;VID=1;USB=1;RAM=64;RAM1=0;; \
+ M5475DFE_config) BOOT=2;CODE=0;VID=0;USB=1;RAM=64;RAM1=0;; \
+ M5475EFE_config) BOOT=2;CODE=0;VID=1;USB=1;RAM=64;RAM1=0;; \
+ M5475FFE_config) BOOT=2;CODE=32;VID=1;USB=1;RAM=64;RAM1=64;; \
+ M5475GFE_config) BOOT=4;CODE=0;VID=0;USB=0;RAM=64;RAM1=0;; \
+ esac; \
+ >include/config.h ; \
+ echo "#define CFG_BUSCLK 133333333" > $(obj)include/config.h ; \
+ echo "#define CFG_BOOTSZ $${BOOT}" >> $(obj)include/config.h ; \
+ echo "#define CFG_DRAMSZ $${RAM}" >> $(obj)include/config.h ; \
+ if [ "$${RAM1}" != "0" ] ; then \
+ echo "#define CFG_DRAMSZ1 $${RAM1}" >> $(obj)include/config.h ; \
+ fi; \
+ if [ "$${CODE}" != "0" ] ; then \
+ echo "#define CFG_NOR1SZ $${CODE}" >> $(obj)include/config.h ; \
+ fi; \
+ if [ "$${VID}" == "1" ] ; then \
+ echo "#define CFG_VIDEO" >> $(obj)include/config.h ; \
+ fi; \
+ if [ "$${USB}" == "1" ] ; then \
+ echo "#define CFG_USBCTRL" >> $(obj)include/config.h ; \
+ fi
+ @$(MKCONFIG) -a M5475EVB m68k mcf547x_8x m547xevb freescale
+
+M5485AFE_config \
+M5485BFE_config \
+M5485CFE_config \
+M5485DFE_config \
+M5485EFE_config \
+M5485FFE_config \
+M5485GFE_config \
+M5485HFE_config : unconfig
+ @case "$@" in \
+ M5485AFE_config) BOOT=2;CODE=0;VID=0;USB=0;RAM=64;RAM1=0;; \
+ M5485BFE_config) BOOT=2;CODE=16;VID=0;USB=0;RAM=64;RAM1=0;; \
+ M5485CFE_config) BOOT=2;CODE=16;VID=1;USB=1;RAM=64;RAM1=0;; \
+ M5485DFE_config) BOOT=2;CODE=0;VID=0;USB=1;RAM=64;RAM1=0;; \
+ M5485EFE_config) BOOT=2;CODE=0;VID=1;USB=1;RAM=64;RAM1=0;; \
+ M5485FFE_config) BOOT=2;CODE=32;VID=1;USB=1;RAM=64;RAM1=64;; \
+ M5485GFE_config) BOOT=4;CODE=0;VID=0;USB=0;RAM=64;RAM1=0;; \
+ M5485HFE_config) BOOT=2;CODE=;VID=1;USB=0;RAM=64;RAM1=0;; \
+ esac; \
+ >include/config.h ; \
+ echo "#define CFG_BUSCLK 100000000" > $(obj)include/config.h ; \
+ echo "#define CFG_BOOTSZ $${BOOT}" >> $(obj)include/config.h ; \
+ echo "#define CFG_DRAMSZ $${RAM}" >> $(obj)include/config.h ; \
+ if [ "$${RAM1}" != "0" ] ; then \
+ echo "#define CFG_DRAMSZ1 $${RAM1}" >> $(obj)include/config.h ; \
+ fi; \
+ if [ "$${CODE}" != "0" ] ; then \
+ echo "#define CFG_NOR1SZ $${CODE}" >> $(obj)include/config.h ; \
+ fi; \
+ if [ "$${VID}" == "1" ] ; then \
+ echo "#define CFG_VIDEO" >> $(obj)include/config.h ; \
+ fi; \
+ if [ "$${USB}" == "1" ] ; then \
+ echo "#define CFG_USBCTRL" >> $(obj)include/config.h ; \
+ fi
+ @$(MKCONFIG) -a M5485EVB m68k mcf547x_8x m548xevb freescale
+
#########################################################################
## MPC83xx Systems
#########################################################################
- mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
- mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
- mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
+ - mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
- mips Files specific to MIPS CPUs
- mpc5xx Files specific to Freescale MPC5xx CPUs
- mpc5xxx Files specific to Freescale MPC5xxx CPUs
--- /dev/null
+Freescale MCF5475EVB ColdFire Development Board
+================================================
+
+TsiChung Liew(Tsi-Chung.Liew@freescale.com)
+Created Jan 08, 2008
+===========================================
+
+
+Changed files:
+==============
+
+- board/freescale/m547xevb/m547xevb.c Dram setup, IDE pre init, and PCI init
+- board/freescale/m547xevb/mii.c MII init
+- board/freescale/m547xevb/Makefile Makefile
+- board/freescale/m547xevb/config.mk config make
+- board/freescale/m547xevb/u-boot.lds Linker description
+
+- cpu/mcf547x_8x/cpu.c cpu specific code
+- cpu/mcf547x_8x/cpu_init.c Flexbus ChipSelect, Mux pins setup, icache and RTC extra regs
+- cpu/mcf547x_8x/interrupts.c cpu specific interrupt support
+- cpu/mcf547x_8x/slicetimer.c Timer support
+- cpu/mcf547x_8x/speed.c system, pci, flexbus, and cpu clock
+- cpu/mcf547x_8x/Makefile Makefile
+- cpu/mcf547x_8x/config.mk config make
+- cpu/mcf547x_8x/start.S start up assembly code
+
+- doc/README.m5475evb This readme file
+
+- drivers/dma/MCD_dmaApi.c DMA API functions
+- drivers/dma/MCD_tasks.c DMA Tasks
+- drivers/dma/MCD_tasksInit.c DMA Tasks Init
+- drivers/net/fsl_mcdmafec.c ColdFire common DMA FEC driver
+- drivers/serial/mcfuart.c ColdFire common UART driver
+
+- include/MCD_dma.h DMA header file
+- include/MCD_progCheck.h DMA header file
+- include/MCD_tasksInit.h DMA header file
+- include/asm-m68k/bitops.h Bit operation function export
+- include/asm-m68k/byteorder.h Byte order functions
+- include/asm-m68k/errno.h Error Number definition
+- include/asm-m68k/fec.h FEC structure and definition
+- include/asm-m68k/fsl_i2c.h I2C structure and definition
+- include/asm-m68k/fsl_mcddmafec.h DMA FEC structure and definition
+- include/asm-m68k/global_data.h Global data structure
+- include/asm-m68k/immap.h ColdFire specific header file and driver macros
+- include/asm-m68k/immap_547x_8x.h mcf547x_8x specific header file
+- include/asm-m68k/io.h io functions
+- include/asm-m68k/m547x_8x.h mcf547x_8x specific header file
+- include/asm-m68k/posix_types.h Posix
+- include/asm-m68k/processor.h header file
+- include/asm-m68k/ptrace.h Exception structure
+- include/asm-m68k/rtc.h Realtime clock header file
+- include/asm-m68k/string.h String function export
+- include/asm-m68k/timer.h Timer structure and definition
+- include/asm-m68k/types.h Data types definition
+- include/asm-m68k/uart.h Uart structure and definition
+- include/asm-m68k/u-boot.h u-boot structure
+
+- include/configs/M5475EVB.h Board specific configuration file
+
+- lib_m68k/board.c board init function
+- lib_m68k/cache.c
+- lib_m68k/interrupts Coldfire common interrupt functions
+- lib_m68k/m68k_linux.c
+- lib_m68k/traps.c Exception init code
+
+1 MCF547x specific Options/Settings
+====================================
+1.1 pre-loader is no longer suppoer in thie coldfire family
+
+1.2 Configuration settings for M5475EVB Development Board
+CONFIG_MCF547x_8x -- define for all MCF547x_8x CPUs
+CONFIG_M547x -- define for all Freescale MCF547x CPUs
+CONFIG_M5475 -- define for M5475EVB board
+
+CONFIG_MCFUART -- define to use common CF Uart driver
+CFG_UART_PORT -- define UART port number, start with 0, 1 and 2
+CONFIG_BAUDRATE -- define UART baudrate
+
+CONFIG_FSLDMAFEC -- define to use common dma FEC driver
+CONFIG_NET_MULTI -- define to use multi FEC in u-boot
+CONFIG_MII -- enable to use MII driver
+CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c
+CFG_DISCOVER_PHY -- enable PHY discovery
+CFG_RX_ETH_BUFFER -- Set FEC Receive buffer
+CFG_FAULT_ECHO_LINK_DOWN--
+CFG_FEC0_PINMUX -- Set FEC0 Pin configuration
+CFG_FEC1_PINMUX -- Set FEC1 Pin configuration
+CFG_FEC0_MIIBASE -- Set FEC0 MII base register
+CFG_FEC1_MIIBASE -- Set FEC0 MII base register
+MCFFEC_TOUT_LOOP -- set FEC timeout loop
+CONFIG_HAS_ETH1 -- define to enable second FEC in u-boot
+
+CONFIG_CMD_USB -- enable USB commands
+CONFIG_USB_OHCI_NEW -- enable USB OHCI driver
+CONFIG_USB_STORAGE -- enable USB Storage device
+CONFIG_DOS_PARTITION -- enable DOS read/write
+
+CONFIG_SLTTMR -- define to use SLT timer
+
+CONFIG_FSL_I2C -- define to use FSL common I2C driver
+CONFIG_HARD_I2C -- define for I2C hardware support
+CONFIG_SOFT_I2C -- define for I2C bit-banged
+CFG_I2C_SPEED -- define for I2C speed
+CFG_I2C_SLAVE -- define for I2C slave address
+CFG_I2C_OFFSET -- define for I2C base address offset
+CFG_IMMR -- define for MBAR offset
+
+CONFIG_PCI -- define for PCI support
+CONFIG_PCI_PNP -- define for Plug n play support
+CONFIG_SKIPPCI_HOSTBRIDGE -- SKIP PCI Host bridge
+CFG_PCI_MEM_BUS -- PCI memory logical offset
+CFG_PCI_MEM_PHYS -- PCI memory physical offset
+CFG_PCI_MEM_SIZE -- PCI memory size
+CFG_PCI_IO_BUS -- PCI IO logical offset
+CFG_PCI_IO_PHYS -- PCI IO physical offset
+CFG_PCI_IO_SIZE -- PCI IO size
+CFG_PCI_CFG_BUS -- PCI Configuration logical offset
+CFG_PCI_CFG_PHYS -- PCI Configuration physical offset
+CFG_PCI_CFG_SIZE -- PCI Configuration size
+
+CFG_MBAR -- define MBAR offset
+
+CONFIG_MONITOR_IS_IN_RAM -- Not support
+
+CFG_INIT_RAM_ADDR -- defines the base address of the MCF547x internal SRAM
+
+CFG_CSn_BASE -- defines the Chip Select Base register
+CFG_CSn_MASK -- defines the Chip Select Mask register
+CFG_CSn_CTRL -- defines the Chip Select Control register
+
+CFG_SDRAM_BASE -- defines the DRAM Base
+
+2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
+===========================================
+2.1. System memory map:
+ Flash: 0xFF800000-0xFFFFFFFF (8MB)
+ DDR: 0x00000000-0x3FFFFFFF (1024MB)
+ SRAM: 0xF2000000-0xF2000FFF (4KB)
+ PCI: 0x70000000-0x8FFFFFFF (512MB)
+ IP: 0xF0000000-0xFFFFFFFF (256MB)
+
+3. COMPILATION
+==============
+3.1 To create U-Boot the gcc-4.x compiler set (ColdFire ELF or uclinux
+ version) from codesourcery.com was used. Download it from:
+ http://www.codesourcery.com/gnu_toolchains/coldfire/download.html
+
+3.2 Compilation
+ export CROSS_COMPILE=cross-compile-prefix
+ cd u-boot-1.x.x
+ make distclean
+ make M5475AFE_config, or - boot 2MB, RAM 64MB
+ make M5475BFE_config, or - boot 2MB, code 16MB, RAM 64MB
+ make M5475CFE_config, or - boot 2MB, code 16MB, Video, USB, RAM 64MB
+ make M5475DFE_config, or - boot 2MB, USB, RAM 64MB
+ make M5475EFE_config, or - boot 2MB, Video, USB, RAM 64MB
+ make M5475FFE_config, or - boot 2MB, code 32MB, Video, USB, RAM 128MB
+ make M5475GFE_config, or - boot 2MB, RAM 64MB
+ make
+
+5. SCREEN DUMP
+==============
+5.1
+
+U-Boot 1.3.1 (Jan 8 2008 - 12:47:44)
+
+CPU: Freescale MCF5475
+ CPU CLK 266 Mhz BUS CLK 133 Mhz
+Board: Freescale FireEngine 5475 EVB
+I2C: ready
+DRAM: 64 MB
+FLASH: 18 MB
+In: serial
+Out: serial
+Err: serial
+Net: FEC0, FEC1
+-> pri
+bootdelay=1
+baudrate=115200
+ethaddr=00:e0:0c:bc:e5:60
+eth1addr=00:e0:0c:bc:e5:61
+ipaddr=192.162.1.2
+serverip=192.162.1.1
+gatewayip=192.162.1.1
+netmask=255.255.255.0
+hostname=M547xEVB
+netdev=eth0
+loadaddr=10000
+u-boot=u-boot.bin
+load=tftp ${loadaddr) ${u-boot}
+upd=run load; run prog
+prog=prot off bank 1;era ff800000 ff82ffff;cp.b ${loadaddr} ff800000 ${filesize};save
+stdin=serial
+stdout=serial
+stderr=serial
+ethact=FEC0
+mem=65024k
+
+Environment size: 433/8188 bytes
+-> bdin
+memstart = 0x00000000
+memsize = 0x04000000
+flashstart = 0xFF800000
+flashsize = 0x01200000
+flashoffset = 0x00000000
+sramstart = 0xF2000000
+sramsize = 0x00001000
+mbar = 0xF0000000
+busfreq = 133.333 MHz
+pcifreq = 0 MHz
+ethaddr = 00:E0:0C:BC:E5:60
+eth1addr = 00:E0:0C:BC:E5:61
+ip_addr = 192.162.1.2
+baudrate = 115200 bps
+-> ?
+? - alias for 'help'
+autoscr - run script from memory
+base - print or set address offset
+bdinfo - print Board Info structure
+boot - boot default, i.e., run 'bootcmd'
+bootd - boot default, i.e., run 'bootcmd'
+bootelf - Boot from an ELF image in memory
+bootm - boot application image from memory
+bootp - boot image via network using BootP/TFTP protocol
+bootvx - Boot vxWorks from an ELF image
+cmp - memory compare
+coninfo - print console devices and information
+cp - memory copy
+crc32 - checksum calculation
+dcache - enable or disable data cache
+echo - echo args to console
+erase - erase FLASH memory
+flinfo - print FLASH memory information
+go - start application at address 'addr'
+help - print online help
+icache - enable or disable instruction cache
+icrc32 - checksum calculation
+iloop - infinite loop on address range
+imd - i2c memory display
+iminfo - print header information for application image
+imls - list all images found in flash
+imm - i2c memory modify (auto-incrementing)
+imw - memory write (fill)
+inm - memory modify (constant address)
+iprobe - probe to discover valid I2C chip addresses
+itest - return true/false on integer compare
+loadb - load binary file over serial line (kermit mode)
+loads - load S-Record file over serial line
+loady - load binary file over serial line (ymodem mode)
+loop - infinite loop on address range
+md - memory display
+mii - MII utility commands
+mm - memory modify (auto-incrementing)
+mtest - simple RAM test
+mw - memory write (fill)
+nfs - boot image via network using NFS protocol
+nm - memory modify (constant address)
+pci - list and access PCI Configuration Space
+ping - send ICMP ECHO_REQUEST to network host
+printenv- print environment variables
+protect - enable or disable FLASH write protection
+rarpboot- boot image via network using RARP/TFTP protocol
+reset - Perform RESET of the CPU
+run - run commands in an environment variable
+saveenv - save environment variables to persistent storage
+setenv - set environment variables
+sleep - delay execution for some time
+tftpboot- boot image via network using TFTP protocol
+usb - USB sub-system
+usbboot - boot from USB device
+version - print monitor version
+-> usb start
+(Re)start USB...
+USB: OHCI pci controller (1131, 1561) found @(0:17:0)
+OHCI regs address 0x80000000
+scanning bus for devices... 2 USB Device(s) found
+ scanning bus for storage devices... 1 Storage Device(s) found
+->
--- /dev/null
+/*
+ * Configuation settings for the Freescale MCF5475 board.
+ *
+ * Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
+ * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _M5475EVB_H
+#define _M5475EVB_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF547x_8x /* define processor family */
+#define CONFIG_M547x /* define processor type */
+#define CONFIG_M5475 /* define processor type */
+
+#undef DEBUG
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT (0)
+#define CONFIG_BAUDRATE 115200
+#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
+
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */
+
+/* Command line configuration */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#undef CONFIG_CMD_DATE
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_USB
+
+#define CONFIG_SLTTMR
+
+#define CONFIG_FSLDMAFEC
+#ifdef CONFIG_FSLDMAFEC
+# define CONFIG_NET_MULTI 1
+# define CONFIG_MII 1
+# define CONFIG_HAS_ETH1
+
+# define CFG_DISCOVER_PHY
+# define CFG_RX_ETH_BUFFER 32
+# define CFG_TX_ETH_BUFFER 48
+# define CFG_FAULT_ECHO_LINK_DOWN
+
+# define CFG_FEC0_PINMUX 0
+# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE
+# define CFG_FEC1_PINMUX 0
+# define CFG_FEC1_MIIBASE CFG_FEC0_IOBASE
+
+# define MCFFEC_TOUT_LOOP 50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+# ifndef CFG_DISCOVER_PHY
+# define FECDUPLEX FULL
+# define FECSPEED _100BASET
+# else
+# ifndef CFG_FAULT_ECHO_LINK_DOWN
+# define CFG_FAULT_ECHO_LINK_DOWN
+# endif
+# endif /* CFG_DISCOVER_PHY */
+
+# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60
+# define CONFIG_ETH1ADDR 00:e0:0c:bc:e5:61
+# define CONFIG_IPADDR 192.162.1.2
+# define CONFIG_NETMASK 255.255.255.0
+# define CONFIG_SERVERIP 192.162.1.1
+# define CONFIG_GATEWAYIP 192.162.1.1
+# define CONFIG_OVERWRITE_ETHADDR_ONCE
+
+#endif
+
+#ifdef CONFIG_CMD_USB
+# define CONFIG_USB_OHCI_NEW
+# define CONFIG_USB_STORAGE
+
+# ifndef CONFIG_CMD_PCI
+# define CONFIG_CMD_PCI
+# endif
+# define CONFIG_PCI_OHCI
+# define CONFIG_DOS_PARTITION
+
+# undef CFG_USB_OHCI_BOARD_INIT
+# undef CFG_USB_OHCI_CPU_INIT
+# define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+# define CFG_USB_OHCI_SLOT_NAME "isp1561"
+# define CFG_OHCI_SWAP_REG_ACCESS
+#endif
+
+/* I2C */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C /* I2C with hw support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 80000
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_OFFSET 0x00008F00
+#define CFG_IMMR CFG_MBAR
+
+/* PCI */
+#ifdef CONFIG_CMD_PCI
+#define CONFIG_PCI 1
+#define CONFIG_PCI_PNP 1
+#define CONFIG_SKIPPCI_HOSTBRIDGE
+
+#define CFG_PCI_CACHE_LINE_SIZE 8
+
+#define CFG_PCI_MEM_BUS 0x80000000
+#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BUS
+#define CFG_PCI_MEM_SIZE 0x10000000
+
+#define CFG_PCI_IO_BUS 0x71000000
+#define CFG_PCI_IO_PHYS CFG_PCI_IO_BUS
+#define CFG_PCI_IO_SIZE 0x01000000
+
+#define CFG_PCI_CFG_BUS 0x70000000
+#define CFG_PCI_CFG_PHYS CFG_PCI_CFG_BUS
+#define CFG_PCI_CFG_SIZE 0x01000000
+#endif
+
+#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
+#define CONFIG_UDP_CHECKSUM
+
+#ifdef CONFIG_MCFFEC
+# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60
+# define CONFIG_IPADDR 192.162.1.2
+# define CONFIG_NETMASK 255.255.255.0
+# define CONFIG_SERVERIP 192.162.1.1
+# define CONFIG_GATEWAYIP 192.162.1.1
+# define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif /* FEC_ENET */
+
+#define CONFIG_HOSTNAME M547xEVB
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "loadaddr=10000\0" \
+ "u-boot=u-boot.bin\0" \
+ "load=tftp ${loadaddr) ${u-boot}\0" \
+ "upd=run load; run prog\0" \
+ "prog=prot off bank 1;" \
+ "era ff800000 ff82ffff;" \
+ "cp.b ${loadaddr} ff800000 ${filesize};"\
+ "save\0" \
+ ""
+
+#define CONFIG_PRAM 512 /* 512 KB */
+#define CFG_PROMPT "-> "
+#define CFG_LONGHELP /* undef to save memory */
+
+#ifdef CONFIG_CMD_KGDB
+# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+# define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_LOAD_ADDR 0x00010000
+
+#define CFG_HZ 1000
+#define CFG_CLK CFG_BUSCLK
+#define CFG_CPU_CLK CFG_CLK * 2
+
+#define CFG_MBAR 0xF0000000
+#define CFG_INTSRAM (CFG_MBAR + 0x10000)
+#define CFG_INTSRAMSZ 0x8000
+
+/*#define CFG_LATCH_ADDR (CFG_CS1_BASE + 0x80000)*/
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR 0xF2000000
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */
+#define CFG_INIT_RAM_CTRL 0x21
+#define CFG_INIT_RAM1_ADDR (CFG_INIT_RAM_ADDR + CFG_INIT_RAM_END)
+#define CFG_INIT_RAM1_END 0x1000 /* End of used area in internal SRAM */
+#define CFG_INIT_RAM1_CTRL 0x21
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET ((CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) - 0x10)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_CFG1 0x73711630
+#define CFG_SDRAM_CFG2 0x46370000
+#define CFG_SDRAM_CTRL 0xE10B0000
+#define CFG_SDRAM_EMOD 0x40010000
+#define CFG_SDRAM_MODE 0x018D0000
+#define CFG_SDRAM_DRVSTRENGTH 0x000002AA
+#ifdef CFG_DRAMSZ1
+# define CFG_SDRAM_SIZE (CFG_DRAMSZ + CFG_DRAMSZ1)
+#else
+# define CFG_SDRAM_SIZE CFG_DRAMSZ
+#endif
+
+#define CFG_MEMTEST_START CFG_SDRAM_BASE + 0x400
+#define CFG_MEMTEST_END ((CFG_SDRAM_SIZE - 3) << 20)
+
+#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400)
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+
+#define CFG_BOOTPARAMS_LEN 64*1024
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+# define CFG_FLASH_BASE (CFG_CS0_BASE)
+# define CFG_FLASH_CFI_DRIVER 1
+# define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+# define CFG_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
+# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
+# define CFG_FLASH_USE_BUFFER_WRITE
+#ifdef CFG_NOR1SZ
+# define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+# define CFG_FLASH_SIZE ((CFG_NOR1SZ + CFG_BOOTSZ) << 20)
+# define CFG_FLASH_BANKS_LIST { CFG_CS0_BASE, CFG_CS1_BASE }
+#else
+# define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+# define CFG_FLASH_SIZE (CFG_BOOTSZ << 20)
+#endif
+#endif
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#define CFG_ENV_OFFSET 0x2000
+#define CFG_ENV_SECT_SIZE 0x2000
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_IS_EMBEDDED 1
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16
+
+/*-----------------------------------------------------------------------
+ * Chipselect bank definitions
+ */
+/*
+ * CS0 - NOR Flash 1, 2, 4, or 8MB
+ * CS1 - NOR Flash
+ * CS2 - Available
+ * CS3 - Available
+ * CS4 - Available
+ * CS5 - Available
+ */
+#define CFG_CS0_BASE 0xFF800000
+#define CFG_CS0_MASK (((CFG_BOOTSZ << 20) - 1) & 0xFFFF0001)
+#define CFG_CS0_CTRL 0x00101980
+
+#ifdef CFG_NOR1SZ
+#define CFG_CS1_BASE 0xF8000000
+#define CFG_CS1_MASK (((CFG_NOR1SZ << 20) - 1) & 0xFFFF0001)
+#define CFG_CS1_CTRL 0x00000D80
+#endif
+
+#endif /* _M5475EVB_H */
--- /dev/null
+/*
+ * Configuation settings for the Freescale MCF5485 FireEngine board.
+ *
+ * Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
+ * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _M5485EVB_H
+#define _M5485EVB_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF547x_8x /* define processor family */
+#define CONFIG_M548x /* define processor type */
+#define CONFIG_M5485 /* define processor type */
+
+#undef DEBUG
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT (0)
+#define CONFIG_BAUDRATE 115200
+#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
+
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */
+
+/* Command line configuration */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#undef CONFIG_CMD_DATE
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_USB
+
+#define CONFIG_SLTTMR
+
+#define CONFIG_FSLDMAFEC
+#ifdef CONFIG_FSLDMAFEC
+# define CONFIG_NET_MULTI 1
+# define CONFIG_MII 1
+# define CONFIG_HAS_ETH1
+
+# define CFG_DISCOVER_PHY
+# define CFG_RX_ETH_BUFFER 32
+# define CFG_TX_ETH_BUFFER 48
+# define CFG_FAULT_ECHO_LINK_DOWN
+
+# define CFG_FEC0_PINMUX 0
+# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE
+# define CFG_FEC1_PINMUX 0
+# define CFG_FEC1_MIIBASE CFG_FEC0_IOBASE
+
+# define MCFFEC_TOUT_LOOP 50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+# ifndef CFG_DISCOVER_PHY
+# define FECDUPLEX FULL
+# define FECSPEED _100BASET
+# else
+# ifndef CFG_FAULT_ECHO_LINK_DOWN
+# define CFG_FAULT_ECHO_LINK_DOWN
+# endif
+# endif /* CFG_DISCOVER_PHY */
+
+# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60
+# define CONFIG_ETH1ADDR 00:e0:0c:bc:e5:61
+# define CONFIG_IPADDR 192.162.1.2
+# define CONFIG_NETMASK 255.255.255.0
+# define CONFIG_SERVERIP 192.162.1.1
+# define CONFIG_GATEWAYIP 192.162.1.1
+# define CONFIG_OVERWRITE_ETHADDR_ONCE
+
+#endif
+
+#ifdef CONFIG_CMD_USB
+# define CONFIG_USB_STORAGE
+# define CONFIG_DOS_PARTITION
+# define CONFIG_USB_OHCI_NEW
+# ifndef CONFIG_CMD_PCI
+# define CONFIG_CMD_PCI
+# endif
+/*# define CONFIG_PCI_OHCI*/
+# define CFG_USB_OHCI_REGS_BASE 0x80041000
+# define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+# define CFG_USB_OHCI_SLOT_NAME "isp1561"
+# define CFG_OHCI_SWAP_REG_ACCESS
+#endif
+
+/* I2C */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C /* I2C with hw support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 80000
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_OFFSET 0x00008F00
+#define CFG_IMMR CFG_MBAR
+
+/* PCI */
+#ifdef CONFIG_CMD_PCI
+#define CONFIG_PCI 1
+#define CONFIG_PCI_PNP 1
+
+#define CFG_PCI_MEM_BUS 0x80000000
+#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BUS
+#define CFG_PCI_MEM_SIZE 0x10000000
+
+#define CFG_PCI_IO_BUS 0x71000000
+#define CFG_PCI_IO_PHYS CFG_PCI_IO_BUS
+#define CFG_PCI_IO_SIZE 0x01000000
+
+#define CFG_PCI_CFG_BUS 0x70000000
+#define CFG_PCI_CFG_PHYS CFG_PCI_CFG_BUS
+#define CFG_PCI_CFG_SIZE 0x01000000
+#endif
+
+#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
+#define CONFIG_UDP_CHECKSUM
+
+#define CONFIG_HOSTNAME M548xEVB
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "loadaddr=10000\0" \
+ "u-boot=u-boot.bin\0" \
+ "load=tftp ${loadaddr) ${u-boot}\0" \
+ "upd=run load; run prog\0" \
+ "prog=prot off bank 1;" \
+ "era ff800000 ff82ffff;" \
+ "cp.b ${loadaddr} ff800000 ${filesize};"\
+ "save\0" \
+ ""
+
+#define CONFIG_PRAM 512 /* 512 KB */
+#define CFG_PROMPT "-> "
+#define CFG_LONGHELP /* undef to save memory */
+
+#ifdef CONFIG_CMD_KGDB
+# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+# define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_LOAD_ADDR 0x00010000
+
+#define CFG_HZ 1000
+#define CFG_CLK CFG_BUSCLK
+#define CFG_CPU_CLK CFG_CLK * 2
+
+#define CFG_MBAR 0xF0000000
+#define CFG_INTSRAM (CFG_MBAR + 0x10000)
+#define CFG_INTSRAMSZ 0x8000
+
+/*#define CFG_LATCH_ADDR (CFG_CS1_BASE + 0x80000)*/
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR 0xF2000000
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */
+#define CFG_INIT_RAM_CTRL 0x21
+#define CFG_INIT_RAM1_ADDR (CFG_INIT_RAM_ADDR + CFG_INIT_RAM_END)
+#define CFG_INIT_RAM1_END 0x1000 /* End of used area in internal SRAM */
+#define CFG_INIT_RAM1_CTRL 0x21
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET ((CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) - 0x10)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_CFG1 0x73711630
+#define CFG_SDRAM_CFG2 0x46370000
+#define CFG_SDRAM_CTRL 0xE10B0000
+#define CFG_SDRAM_EMOD 0x40010000
+#define CFG_SDRAM_MODE 0x018D0000
+#define CFG_SDRAM_DRVSTRENGTH 0x000002AA
+#ifdef CFG_DRAMSZ1
+# define CFG_SDRAM_SIZE (CFG_DRAMSZ + CFG_DRAMSZ1)
+#else
+# define CFG_SDRAM_SIZE CFG_DRAMSZ
+#endif
+
+#define CFG_MEMTEST_START CFG_SDRAM_BASE + 0x400
+#define CFG_MEMTEST_END ((CFG_SDRAM_SIZE - 3) << 20)
+
+#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400)
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+
+#define CFG_BOOTPARAMS_LEN 64*1024
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+# define CFG_FLASH_BASE (CFG_CS0_BASE)
+# define CFG_FLASH_CFI_DRIVER 1
+# define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+# define CFG_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
+# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
+# define CFG_FLASH_USE_BUFFER_WRITE
+#ifdef CFG_NOR1SZ
+# define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+# define CFG_FLASH_SIZE ((CFG_NOR1SZ + CFG_BOOTSZ) << 20)
+# define CFG_FLASH_BANKS_LIST { CFG_CS0_BASE, CFG_CS1_BASE }
+#else
+# define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+# define CFG_FLASH_SIZE (CFG_BOOTSZ << 20)
+#endif
+#endif
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#define CFG_ENV_OFFSET 0x2000
+#define CFG_ENV_SECT_SIZE 0x2000
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_IS_EMBEDDED 1
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16
+
+/*-----------------------------------------------------------------------
+ * Chipselect bank definitions
+ */
+/*
+ * CS0 - NOR Flash 1, 2, 4, or 8MB
+ * CS1 - NOR Flash
+ * CS2 - Available
+ * CS3 - Available
+ * CS4 - Available
+ * CS5 - Available
+ */
+#define CFG_CS0_BASE 0xFF800000
+#define CFG_CS0_MASK (((CFG_BOOTSZ << 20) - 1) & 0xFFFF0001)
+#define CFG_CS0_CTRL 0x00101980
+
+#ifdef CFG_NOR1SZ
+#define CFG_CS1_BASE 0xF8000000
+#define CFG_CS1_MASK (((CFG_NOR1SZ << 20) - 1) & 0xFFFF0001)
+#define CFG_CS1_CTRL 0x00000D80
+#endif
+
+#endif /* _M5485EVB_H */
projects / karo-tx-uboot.git / commitdiff