ifndef TEXT_BASE
TEXT_BASE = 0xFFFA0000
+#
+# When defining CONFIG_VIDEO, TEXT_BASE needs to be 0xFFF80000
+# TEXT_BASE = 0xFFF80000
+#
endif
PLATFORM_CPPFLAGS += -DCONFIG_440=1
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME ocotea
+#include "amcc-common.h"
+
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xff800000 /* start of FLASH */
-#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
-
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE 115200
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*-----------------------------------------------------------------------
* Environment
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=ocotea\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/ocotea/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff00000\0" \
"ramdisk_addr=fff10000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/ocotea/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_PHY1_ADDR 2
#define CONFIG_PHY2_ADDR 0x10
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
/* This config file is used for Sequoia (440EPx) and Rainier (440GRx) */
#ifndef CONFIG_RAINIER
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
+#define CONFIG_HOSTNAME sequoia
#else
#define CONFIG_440GRX 1 /* Specific PPC440GRx */
+#define CONFIG_HOSTNAME rainier
#endif
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
/* Detect Sequoia PLL input clock automatically via CPLD bit */
#define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \
33333333 : 33000000)
* Base addresses -- Note these are effective addresses where the actual
* resources get mapped (not physical addresses).
*/
-#ifndef CONFIG_VIDEO
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kiB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kiB for malloc() */
-#else
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */
-#endif
-
#define CFG_TLB_FOR_BOOT_FLASH 0x0003
#define CFG_BOOT_BASE_ADDR 0xf0000000
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
-#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */
#define CFG_OCM_BASE 0xe0010000 /* ocm */
#define CFG_OCM_DATA_ADDR CFG_OCM_BASE
* Serial Port
*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*
* Environment
*/
/*
* I2C
*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#ifndef CONFIG_RAINIER
-#define CONFIG_HOSTNAME sequoia
-#define CFG_BOOTFILE "bootfile=sequoia/uImage\0"
-#define CFG_DTBFILE "fdt_file=sequoia/sequoia.dtb\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_HOSTNAME rainier
-#define CFG_BOOTFILE "bootfile=rainier/uImage\0"
-#define CFG_DTBFILE "fdt_file=rainier/rainier.dtb\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0"
-#endif
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- CFG_BOOTFILE \
- CFG_ROOTPATH \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "addmisc=setenv bootargs ${bootargs}\0" \
- "flash_nfs=run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};" \
- "run nfsargs addip addtty addmisc;" \
- "bootm\0" \
- "fdt_file=sequoia/sequoia.dtb\0" \
- "fdt_addr=400000\0" \
- "net_nfs_fdt=tftp 200000 ${bootfile};" \
- "tftp ${fdt_addr} ${fdt_file};" \
- "run nfsargs addip addtty addmisc;" \
- "bootm 200000 - ${fdt_addr}\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"kernel_addr=FC000000\0" \
"ramdisk_addr=FC180000\0" \
- "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \
- "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
- "cp.b 200000 FFFA0000 60000\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_M88E1111_PHY 1
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_HAS_ETH0
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx */
- /* buffers & descriptors */
-#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 1
#define CONFIG_ISO_PARTITION
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#ifdef CONFIG_440EPX
#define CONFIG_SUPPORT_VFAT
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
- /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*
* PCI stuff
*/
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data have to be in the
- * first 8 MB of memory, since this is the maximum mapped by the Linux kernel
- * during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*
* External Bus Controller (EBC) Setup
*/
} \
}
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#ifdef CONFIG_VIDEO
#define CONFIG_BIOSEMU /* x86 bios emulator for vga bios */
#define CONFIG_ATI_RADEON_FB /* use radeon framebuffer driver */
#define CONFIG_4xx 1 /* member of PPC4xx family */
#define CONFIG_TAIHU 1 /* on a taihu board */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME taihu
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#define CONFIG_ENV_OVERWRITE 1
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "bootfile=/tftpboot/taihu/uImage\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "netdev=eth0\0" \
- "hostname=taihu\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
+/*
+ * Default environment variables
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=FC000000\0" \
"ramdisk_addr=FC180000\0" \
- "load=tftp 200000 /tftpboot/taihu/u-boot.bin\0" \
- "update=protect off FFFC0000 FFFFFFFF;era FFFC0000 FFFFFFFF;" \
- "cp.b 200000 FFFC0000 40000\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0x14 /* PHY address */
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_PHY1_ADDR 0x10 /* EMAC1 PHY address */
-#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */
#define CONFIG_PHY_RESET 1
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SPI
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
#undef CONFIG_SPD_EEPROM /* use SPD EEPROM for setup */
#define CFG_SDRAM_SIZE_PER_BANK 0x04000000 /* 64MB */
#define CFG_SDRAM_BANKS 2
#define CFG_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */
#define CFG_SDRAM_tRFC 66 /* Auto refresh period */
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
/*
* If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
* If CFG_405_UART_ERRATA_59, then UART divisor is 31.
#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
#define CFG_BASE_BAUD 691200
-
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_UART1_CONSOLE 1
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
/*-----------------------------------------------------------------------
* I2C stuff
*-----------------------------------------------------------------------
*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFFE00000
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CPLD_REG0_ADDR 0x50100000
#define CPLD_REG1_ADDR 0x50100001
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
#endif /* __CONFIG_H */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME taishan
+#define CONFIG_USE_TTY ttyS1
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
-#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/
-#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc*/
-
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#define CONFIG_UART1_CONSOLE 1 /* use of UART1 as console */
-#define CONFIG_SERIAL_MULTI 1 /* enable serial multi support */
#define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE 115200
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*-----------------------------------------------------------------------
* Environment
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#undef CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR 0x50
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=taishan\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/taishan/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fc000000\0" \
"ramdisk_addr=fc180000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/taishan/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "fixedip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
- "$(gatewayip):$(netmask):$(hostname):$(netdev):off panic=1\0" \
- "dhcp=setenv bootargs $(bootargs) ip=dhcp\0" \
"kozio=bootm 0xffe00000\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*-----------------------------------------------------------------------
* Networking
*----------------------------------------------------------------------*/
#define CONFIG_EMAC_NR_START 2 /* start with EMAC 2 (skip 0&1) */
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_NET_MULTI 1
#define CONFIG_PHY_ADDR 0xff /* no phy on EMAC0 */
#define CONFIG_PHY1_ADDR 0xff /* no phy on EMAC1 */
#define CONFIG_PHY2_ADDR 0x1
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* PCI stuff
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_WALNUT 1 /* ...on a WALNUT board */
/* ...and on a SYCAMORE board */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME walnut
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=walnut\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/walnut/uImage\0" \
+/*
+ * Default environment variables
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff80000\0" \
"ramdisk_addr=fff80000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/walnut/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
-
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
#define CONFIG_HAS_ETH0 1
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* needed for NetConsole */
-
#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Walnut */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
/*
* If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
* If CFG_405_UART_ERRATA_59, then UART divisor is 31.
#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
#define CFG_BASE_BAUD 691200
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* I2C stuff
*-----------------------------------------------------------------------
*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFFF80000
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
/*
* Define here the location of the environment variables (FLASH or NVRAM).
#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
#endif
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* FLASH organization
*/
*/
#define SPD_EEPROM_ADDRESS 0x50
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
#define CONFIG_BOARD_RESET 1 /* call board_reset() */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/
#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
* Serial Port
*----------------------------------------------------------------------*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
/*define this if you want console on UART1*/
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#ifndef CONFIG_YELLOWSTONE
-#define CONFIG_HOSTNAME yosemite
-#define CFG_BOOTFILE "bootfile=/tftpboot/yosemite/uImage\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_HOSTNAME yellowstone
-#define CFG_BOOTFILE "bootfile=/tftpboot/yellowstone/uImage\0"
-#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0"
-#endif
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- CFG_BOOTFILE \
- CFG_ROOTPATH \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "bootfile=/tftpboot/${hostname}/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fc000000\0" \
"ramdisk_addr=fc180000\0" \
- "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \
- "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \
- "cp.b 200000 fff80000 80000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_NET_MULTI 1 /* required for netconsole */
-#define CONFIG_PHY1_ADDR 3
#define CONFIG_HAS_ETH0 1 /* add support for "ethaddr" */
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
-
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_PHY1_ADDR 3
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_HW_WATCHDOG /* watchdog */
#endif
-
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
#define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SDRAM
#ifdef CONFIG_440EP
#define CONFIG_CMD_USB
#define CONFIG_CMD_EXT2
#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CONFIG_LYNXKDI 1 /* support kdi files */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
#define CFG_BCSR5_PCI66EN 0x80
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
#define EXTCLK_50 50000000
#define EXTCLK_83 83333333
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME yucca
+#include "amcc-common.h"
+
#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
#undef CONFIG_SHOW_BOOT_PROGRESS
#undef CONFIG_STRESS
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */
-#define CFG_MONITOR_BASE 0xfffb0000 /* start of monitor */
#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */
#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
-#define CFG_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Mon */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */
-
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#define CONFIG_SERIAL_MULTI 1
#undef CONFIG_UART1_CONSOLE
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#undef CFG_EXT_SERIAL_CLOCK
/* #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) */ /* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE 115200
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define IIC0_BOOTPROM_ADDR 0x50
#define IIC0_ALT_BOOTPROM_ADDR 0x54
#undef CFG_ENV_IS_IN_EEPROM /* ... not in EEPROM */
#define CONFIG_ENV_OVERWRITE 1
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=yucca\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=yucca/uImage\0" \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_PPC \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=E7F10000\0" \
"ramdisk_addr=E7F20000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 yuca/u-boot.bin\0" \
- "update=protect off 2:4-7;era 2:4-7;" \
- "cp.b ${fileaddr} FFFB0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:EP:EP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
-
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
-#undef CONFIG_NET_MULTI
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_HAS_ETH0
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_RESET_DELAY 1000
#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* needed for NetConsole */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* FLASH related
/* Support for Intel 82557/82559/82559ER chips. */
#define CONFIG_EEPRO100
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
/* FB Divisor selection */
#define FPGA_FB_DIV_6 6
#define FPGA_FB_DIV_10 10
#define PERIOD_33_33MHZ 30000 /* 30ns */
#define PERIOD_25_00MHZ 40000 /* 40ns */
-/*---------------------------------------------------------------------------*/
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / commitdiff