drivers/power/battery/
LIBS-y += drivers/spi/
LIBS-$(CONFIG_FMAN_ENET) += drivers/net/fm/
+LIBS-$(CONFIG_SYS_FSL_DDR) += drivers/ddr/fsl/
LIBS-y += drivers/serial/
LIBS-y += drivers/usb/eth/
LIBS-y += drivers/usb/gadget/
CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
This value denotes start offset of DSP CCSR space.
- CONFIG_SYS_FSL_DDR_EMU
- Specify emulator support for DDR. Some DDR features such as
- deskew training are not available.
-
- Generic CPU options:
CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
Defines the endianess of the CPU. Implementation of those
values is arch specific.
+ CONFIG_SYS_FSL_DDR
+ Freescale DDR driver in use. This type of DDR controller is
+ found in mpc83xx, mpc85xx, mpc86xx as well as some ARM core
+ SoCs.
+
+ CONFIG_SYS_FSL_DDR_ADDR
+ Freescale DDR memory-mapped register base.
+
+ CONFIG_SYS_FSL_DDR_EMU
+ Specify emulator support for DDR. Some DDR features such as
+ deskew training are not available.
+
+ CONFIG_SYS_FSL_DDRC_GEN1
+ Freescale DDR1 controller.
+
+ CONFIG_SYS_FSL_DDRC_GEN2
+ Freescale DDR2 controller.
+
+ CONFIG_SYS_FSL_DDRC_GEN3
+ Freescale DDR3 controller.
+
+ CONFIG_SYS_FSL_DDRC_ARM_GEN3
+ Freescale DDR3 controller for ARM-based SoCs.
+
+ CONFIG_SYS_FSL_DDR1
+ Board config to use DDR1. It can be enabled for SoCs with
+ Freescale DDR1 or DDR2 controllers, depending on the board
+ implemetation.
+
+ CONFIG_SYS_FSL_DDR2
+ Board config to use DDR2. It can be eanbeld for SoCs with
+ Freescale DDR2 or DDR3 controllers, depending on the board
+ implementation.
+
+ CONFIG_SYS_FSL_DDR3
+ Board config to use DDR3. It can be enabled for SoCs with
+ Freescale DDR3 controllers.
+
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
Set for the SPL on PPC mpc8xxx targets, support for
- arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary.
+ drivers/ddr/fsl/libddr.o in SPL binary.
CONFIG_SPL_COMMON_INIT_DDR
Set for common ddr init with serial presence detect in
# Stub implementations of cache management functions for USB
obj-y += cache.o
-ifdef CONFIG_FSL_DDR2
-obj-$(CONFIG_MPC8349) += ../mpc85xx/ddr-gen2.o
+ifdef CONFIG_SYS_FSL_DDR2
+obj-$(CONFIG_MPC8349) += $(SRCTREE)/drivers/ddr/fsl/mpc85xx_ddr_gen2.o
else
obj-y += spd_sdram.o
endif
-obj-$(CONFIG_FSL_DDR2) += law.o
+obj-$(CONFIG_SYS_FSL_DDR2) += law.o
endif # not minimal
void ecc_print_status(void)
{
immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-#ifdef CONFIG_FSL_DDR2
- ccsr_ddr_t *ddr = &immap->ddr;
+#ifdef CONFIG_SYS_FSL_DDR2
+ struct ccsr_ddr __iomem *ddr = &immap->ddr;
#else
ddr83xx_t *ddr = &immap->ddr;
#endif
int do_ecc(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
{
immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-#ifdef CONFIG_FSL_DDR2
- ccsr_ddr_t *ddr = &immap->ddr;
+#ifdef CONFIG_SYS_FSL_DDR2
+ struct ccsr_ddr __iomem *ddr = &immap->ddr;
#else
ddr83xx_t *ddr = &immap->ddr;
#endif
obj-$(CONFIG_CMD_ERRATA) += cmd_errata.o
obj-$(CONFIG_CPM2) += commproc.o
-# supports ddr1
-obj-$(CONFIG_MPC8540) += ddr-gen1.o
-obj-$(CONFIG_MPC8560) += ddr-gen1.o
-obj-$(CONFIG_MPC8541) += ddr-gen1.o
-obj-$(CONFIG_MPC8555) += ddr-gen1.o
-
-# supports ddr1/2
-obj-$(CONFIG_MPC8548) += ddr-gen2.o
-obj-$(CONFIG_MPC8568) += ddr-gen2.o
-obj-$(CONFIG_MPC8544) += ddr-gen2.o
-
-# supports ddr1/2/3
-obj-$(CONFIG_PPC_C29X) += ddr-gen3.o
-obj-$(CONFIG_MPC8572) += ddr-gen3.o
-obj-$(CONFIG_MPC8536) += ddr-gen3.o
-obj-$(CONFIG_MPC8569) += ddr-gen3.o
-obj-$(CONFIG_P1010) += ddr-gen3.o
-obj-$(CONFIG_P1011) += ddr-gen3.o
-obj-$(CONFIG_P1012) += ddr-gen3.o
-obj-$(CONFIG_P1013) += ddr-gen3.o
-obj-$(CONFIG_P1014) += ddr-gen3.o
-obj-$(CONFIG_P1020) += ddr-gen3.o
-obj-$(CONFIG_P1021) += ddr-gen3.o
-obj-$(CONFIG_P1022) += ddr-gen3.o
-obj-$(CONFIG_P1023) += ddr-gen3.o
-obj-$(CONFIG_P1024) += ddr-gen3.o
-obj-$(CONFIG_P1025) += ddr-gen3.o
-obj-$(CONFIG_P2010) += ddr-gen3.o
-obj-$(CONFIG_P2020) += ddr-gen3.o
-obj-$(CONFIG_PPC_P2041) += ddr-gen3.o
-obj-$(CONFIG_PPC_P3041) += ddr-gen3.o
-obj-$(CONFIG_PPC_P4080) += ddr-gen3.o
-obj-$(CONFIG_PPC_P5020) += ddr-gen3.o
-obj-$(CONFIG_PPC_P5040) += ddr-gen3.o
-obj-$(CONFIG_PPC_T4240) += ddr-gen3.o
-obj-$(CONFIG_PPC_T4160) += ddr-gen3.o
-obj-$(CONFIG_PPC_B4420) += ddr-gen3.o
-obj-$(CONFIG_PPC_B4860) += ddr-gen3.o
-obj-$(CONFIG_BSC9131) += ddr-gen3.o
-obj-$(CONFIG_BSC9132) += ddr-gen3.o
-obj-$(CONFIG_PPC_T1040) += ddr-gen3.o
-obj-$(CONFIG_PPC_T1042) += ddr-gen3.o
-obj-$(CONFIG_PPC_T1020) += ddr-gen3.o
-obj-$(CONFIG_PPC_T1022) += ddr-gen3.o
-
obj-$(CONFIG_CPM2) += ether_fcc.o
obj-$(CONFIG_OF_LIBFDT) += fdt.o
obj-$(CONFIG_FSL_CORENET) += liodn.o
obj-$(CONFIG_PPC_T1042) += t1040_ids.o
obj-$(CONFIG_PPC_T1020) += t1040_ids.o
obj-$(CONFIG_PPC_T1022) += t1040_ids.o
+obj-$(CONFIG_PPC_T2080) += t2080_ids.o
+obj-$(CONFIG_PPC_T2081) += t2080_ids.o
obj-$(CONFIG_QE) += qe_io.o
obj-$(CONFIG_PPC_T1042) += t1040_serdes.o
obj-$(CONFIG_PPC_T1020) += t1040_serdes.o
obj-$(CONFIG_PPC_T1022) += t1040_serdes.o
+obj-$(CONFIG_PPC_T2080) += t2080_serdes.o
+obj-$(CONFIG_PPC_T2081) += t2080_serdes.o
obj-y += cpu.o
obj-y += cpu_init.o
#include <asm/cache.h>
#include <asm/io.h>
#include <asm/mmu.h>
-#include <asm/fsl_ifc.h>
+#include <fsl_ifc.h>
#include <asm/fsl_law.h>
#include <asm/fsl_lbc.h>
#include <post.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
DECLARE_GLOBAL_DATA_PTR;
int i, j, k, m;
u8 *p_8;
u32 *p_32;
- ccsr_ddr_t *ddr[CONFIG_NUM_DDR_CONTROLLERS];
+ struct ccsr_ddr __iomem *ddr[CONFIG_NUM_DDR_CONTROLLERS];
generic_spd_eeprom_t
spd[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR];
for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
switch (i) {
case 0:
- ddr[i] = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ddr[i] = (void *)CONFIG_SYS_FSL_DDR_ADDR;
break;
-#if defined(CONFIG_SYS_MPC8xxx_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
+#if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
case 1:
- ddr[i] = (void *)CONFIG_SYS_MPC8xxx_DDR2_ADDR;
+ ddr[i] = (void *)CONFIG_SYS_FSL_DDR2_ADDR;
break;
#endif
-#if defined(CONFIG_SYS_MPC8xxx_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
+#if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
case 2:
- ddr[i] = (void *)CONFIG_SYS_MPC8xxx_DDR3_ADDR;
+ ddr[i] = (void *)CONFIG_SYS_FSL_DDR3_ADDR;
break;
#endif
-#if defined(CONFIG_SYS_MPC8xxx_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
+#if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
case 3:
- ddr[i] = (void *)CONFIG_SYS_MPC8xxx_DDR4_ADDR;
+ ddr[i] = (void *)CONFIG_SYS_FSL_DDR4_ADDR;
break;
#endif
default:
for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++)
printf(" Base + 0x%04x", (u32)ddr[i] & 0xFFFF);
puts("\n");
- for (k = 0; k < sizeof(ccsr_ddr_t)/4; k++) {
+ for (k = 0; k < sizeof(struct ccsr_ddr)/4; k++) {
m = 0;
printf("%6d (0x%04x)", k * 4, k * 4);
for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
#include <asm/io.h>
#include <asm/mmu.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include "mp.h"
DECLARE_GLOBAL_DATA_PTR;
sys_info->freq_processor[cpu] =
freq_c_pll[cplx_pll] / core_cplx_pll_div[c_pll_sel];
}
-#ifdef CONFIG_PPC_B4860
+#if defined(CONFIG_PPC_B4860) || defined(CONFIG_PPC_T2080)
#define FM1_CLK_SEL 0xe0000000
#define FM1_CLK_SHIFT 29
#else
#include <common.h>
#include <asm/processor.h>
#include <asm/global_data.h>
-#include <asm/fsl_ifc.h>
+#include <fsl_ifc.h>
#include <asm/io.h>
DECLARE_GLOBAL_DATA_PTR;
--- /dev/null
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+
+#ifdef CONFIG_SYS_DPAA_QBMAN
+struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = {
+ /* dqrr liodn, frame data liodn, liodn off, sdest */
+ SET_QP_INFO(1, 27, 1, 0),
+ SET_QP_INFO(2, 28, 1, 0),
+ SET_QP_INFO(3, 29, 1, 1),
+ SET_QP_INFO(4, 30, 1, 1),
+ SET_QP_INFO(5, 31, 1, 2),
+ SET_QP_INFO(6, 32, 1, 2),
+ SET_QP_INFO(7, 33, 1, 3),
+ SET_QP_INFO(8, 34, 1, 3),
+ SET_QP_INFO(9, 35, 1, 0),
+ SET_QP_INFO(10, 36, 1, 0),
+ SET_QP_INFO(11, 37, 1, 1),
+ SET_QP_INFO(12, 38, 1, 1),
+ SET_QP_INFO(13, 39, 1, 2),
+ SET_QP_INFO(14, 40, 1, 2),
+ SET_QP_INFO(15, 41, 1, 3),
+ SET_QP_INFO(16, 42, 1, 3),
+ SET_QP_INFO(17, 43, 1, 0),
+ SET_QP_INFO(18, 44, 1, 0),
+};
+#endif
+
+#ifdef CONFIG_SYS_SRIO
+struct srio_liodn_id_table srio_liodn_tbl[] = {
+ SET_SRIO_LIODN_BASE(1, 307),
+ SET_SRIO_LIODN_BASE(2, 387),
+};
+int srio_liodn_tbl_sz = ARRAY_SIZE(srio_liodn_tbl);
+#endif
+
+struct liodn_id_table liodn_tbl[] = {
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ SET_QMAN_LIODN(62),
+ SET_BMAN_LIODN(63),
+#endif
+
+ SET_SDHC_LIODN(1, 552),
+
+ SET_PME_LIODN(117),
+
+ SET_USB_LIODN(1, "fsl-usb2-mph", 553),
+ SET_USB_LIODN(2, "fsl-usb2-dr", 554),
+
+ SET_SATA_LIODN(1, 555),
+ SET_SATA_LIODN(2, 556),
+
+ SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 1, 148),
+ SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 228),
+ SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 308),
+ SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 388),
+
+ SET_DMA_LIODN(1, 147),
+ SET_DMA_LIODN(2, 227),
+ SET_DMA_LIODN(3, 226),
+
+ SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0),
+ SET_GUTS_LIODN(NULL, 200, rio2liodnr, 0),
+ SET_GUTS_LIODN(NULL, 201, rio1maintliodnr, 0),
+ SET_GUTS_LIODN(NULL, 202, rio2maintliodnr, 0),
+
+#ifdef CONFIG_SYS_PMAN
+ SET_PMAN_LIODN(1, 513),
+ SET_PMAN_LIODN(2, 514),
+ SET_PMAN_LIODN(3, 515),
+#endif
+
+ /* SET_NEXUS_LIODN(557), -- not yet implemented */
+};
+int liodn_tbl_sz = ARRAY_SIZE(liodn_tbl);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+struct liodn_id_table fman1_liodn_tbl[] = {
+ SET_FMAN_RX_1G_LIODN(1, 0, 88),
+ SET_FMAN_RX_1G_LIODN(1, 1, 89),
+ SET_FMAN_RX_1G_LIODN(1, 2, 90),
+ SET_FMAN_RX_1G_LIODN(1, 3, 91),
+ SET_FMAN_RX_1G_LIODN(1, 4, 92),
+ SET_FMAN_RX_1G_LIODN(1, 5, 93),
+ SET_FMAN_RX_10G_LIODN(1, 0, 94),
+ SET_FMAN_RX_10G_LIODN(1, 1, 95),
+};
+int fman1_liodn_tbl_sz = ARRAY_SIZE(fman1_liodn_tbl);
+#endif
+
+struct liodn_id_table sec_liodn_tbl[] = {
+ SET_SEC_JR_LIODN_ENTRY(0, 454, 458),
+ SET_SEC_JR_LIODN_ENTRY(1, 455, 459),
+ SET_SEC_JR_LIODN_ENTRY(2, 456, 460),
+ SET_SEC_JR_LIODN_ENTRY(3, 457, 461),
+ SET_SEC_RTIC_LIODN_ENTRY(a, 453),
+ SET_SEC_RTIC_LIODN_ENTRY(b, 549),
+ SET_SEC_RTIC_LIODN_ENTRY(c, 550),
+ SET_SEC_RTIC_LIODN_ENTRY(d, 551),
+ SET_SEC_DECO_LIODN_ENTRY(0, 541, 610),
+ SET_SEC_DECO_LIODN_ENTRY(1, 542, 611),
+ SET_SEC_DECO_LIODN_ENTRY(2, 543, 612),
+ SET_SEC_DECO_LIODN_ENTRY(3, 544, 613),
+ SET_SEC_DECO_LIODN_ENTRY(4, 545, 614),
+ SET_SEC_DECO_LIODN_ENTRY(5, 546, 615),
+ SET_SEC_DECO_LIODN_ENTRY(6, 547, 616),
+ SET_SEC_DECO_LIODN_ENTRY(7, 548, 617),
+};
+int sec_liodn_tbl_sz = ARRAY_SIZE(sec_liodn_tbl);
+
+#ifdef CONFIG_SYS_DPAA_RMAN
+struct liodn_id_table rman_liodn_tbl[] = {
+ /* Set RMan block 0-3 liodn offset */
+ SET_RMAN_LIODN(0, 6),
+ SET_RMAN_LIODN(1, 7),
+ SET_RMAN_LIODN(2, 8),
+ SET_RMAN_LIODN(3, 9),
+};
+int rman_liodn_tbl_sz = ARRAY_SIZE(rman_liodn_tbl);
+#endif
+
+struct liodn_id_table liodn_bases[] = {
+#ifdef CONFIG_SYS_DPAA_DCE
+ [FSL_HW_PORTAL_DCE] = SET_LIODN_BASE_2(618, 694),
+#endif
+ [FSL_HW_PORTAL_SEC] = SET_LIODN_BASE_2(462, 558),
+#ifdef CONFIG_SYS_DPAA_FMAN
+ [FSL_HW_PORTAL_FMAN1] = SET_LIODN_BASE_1(973),
+#endif
+#ifdef CONFIG_SYS_DPAA_PME
+ [FSL_HW_PORTAL_PME] = SET_LIODN_BASE_2(770, 846),
+#endif
+#ifdef CONFIG_SYS_DPAA_RMAN
+ [FSL_HW_PORTAL_RMAN] = SET_LIODN_BASE_1(922),
+#endif
+};
--- /dev/null
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * Shengzhou Liu <Shengzhou.Liu@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_serdes.h>
+#include <asm/processor.h>
+#include "fsl_corenet2_serdes.h"
+
+struct serdes_config {
+ u32 protocol;
+ u8 lanes[SRDS_MAX_LANES];
+};
+
+static const struct serdes_config serdes1_cfg_tbl[] = {
+ /* SerDes 1 */
+ {0x6E, {XFI_FM1_MAC9, XFI_FM1_MAC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ PCIE4, PCIE4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0xBC, {PCIE3, PCIE3, SGMII_FM1_DTSEC1,
+ SGMII_FM1_DTSEC2, PCIE4, PCIE4, PCIE4, PCIE4} },
+ {0xC8, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1,
+ SGMII_FM1_DTSEC2, PCIE4, PCIE4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0xD6, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1,
+ SGMII_FM1_DTSEC2, PCIE4, PCIE4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0xDE, {PCIE3, PCIE3, PCIE3, PCIE3,
+ PCIE4, PCIE1, PCIE2, SGMII_FM1_DTSEC6} },
+ {0xE0, {PCIE3, PCIE3, PCIE3, PCIE3, PCIE4,
+ PCIE1, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0xF2, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1,
+ SGMII_FM1_DTSEC2, PCIE4, PCIE1, PCIE2, SGMII_FM1_DTSEC6} },
+ {0xF8, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1,
+ SGMII_FM1_DTSEC2, PCIE4, PCIE1, PCIE2, SGMII_FM1_DTSEC6} },
+ {0xFA, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1,
+ SGMII_FM1_DTSEC2, PCIE4, PCIE1,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x6C, {XFI_FM1_MAC9, XFI_FM1_MAC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ PCIE4, PCIE4, PCIE4, PCIE4} },
+#if defined(CONFIG_PPC_T2080)
+ {0x1C, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x95, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0xA2, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x94, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x51, {XAUI_FM1_MAC9, XAUI_FM1_MAC9,
+ XAUI_FM1_MAC9, XAUI_FM1_MAC9,
+ PCIE4, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x5F, {HIGIG_FM1_MAC9, HIGIG_FM1_MAC9,
+ HIGIG_FM1_MAC9, HIGIG_FM1_MAC9,
+ PCIE4, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x65, {HIGIG_FM1_MAC9, HIGIG_FM1_MAC9,
+ HIGIG_FM1_MAC9, HIGIG_FM1_MAC9,
+ PCIE4, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x6B, {XFI_FM1_MAC9, XFI_FM1_MAC10,
+ XFI_FM1_MAC1, XFI_FM1_MAC2,
+ PCIE4, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x6D, {XFI_FM1_MAC9, XFI_FM1_MAC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ PCIE4, PCIE4, PCIE4, PCIE4} },
+ {0x71, {XFI_FM1_MAC9, XFI_FM1_MAC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, PCIE4,
+ SGMII_FM1_DTSEC4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0xA6, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, PCIE4,
+ PCIE4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x8E, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, PCIE4,
+ PCIE4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x8F, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2, PCIE4,
+ PCIE4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x82, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ PCIE4, PCIE4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x83, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ PCIE4, PCIE4, SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0xA4, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ PCIE4, PCIE4, PCIE4, PCIE4} },
+ {0x96, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ PCIE4, PCIE4, PCIE4, PCIE4} },
+ {0x8A, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10,
+ SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ PCIE4, PCIE4, PCIE4, PCIE4} },
+ {0x67, {XFI_FM1_MAC9, XFI_FM1_MAC10,
+ XFI_FM1_MAC1, XFI_FM1_MAC2,
+ PCIE4, PCIE4, PCIE4, PCIE4} },
+ {0xAB, {PCIE3, PCIE3, PCIE3, PCIE3,
+ PCIE4, PCIE4, PCIE4, PCIE4} },
+ {0xDA, {PCIE3, PCIE3, PCIE3, PCIE3,
+ PCIE3, PCIE3, PCIE3, PCIE3} },
+ {0xD9, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1,
+ SGMII_FM1_DTSEC2, PCIE4, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0xD3, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1,
+ SGMII_FM1_DTSEC2, PCIE4, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0xCB, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1,
+ SGMII_FM1_DTSEC2, PCIE4, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0xD8, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1,
+ SGMII_FM1_DTSEC2, PCIE4, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x66, {XFI_FM1_MAC9, XFI_FM1_MAC10,
+ XFI_FM1_MAC1, XFI_FM1_MAC2,
+ PCIE4, PCIE4, PCIE4, PCIE4} },
+
+#elif defined(CONFIG_PPC_T2081)
+ {0xAA, {PCIE3, PCIE3, PCIE3, PCIE3,
+ PCIE4, PCIE4, PCIE4, PCIE4} },
+ {0xCA, {PCIE3, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC1,
+ SGMII_FM1_DTSEC2, PCIE4, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+ {0x70, {XFI_FM1_MAC9, XFI_FM1_MAC10, SGMII_FM1_DTSEC1,
+ SGMII_FM1_DTSEC2, PCIE4, SGMII_FM1_DTSEC4,
+ SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+#endif
+ {}
+};
+
+#ifndef CONFIG_PPC_T2081
+static const struct serdes_config serdes2_cfg_tbl[] = {
+ /* SerDes 2 */
+ {0x1F, {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, PCIE2, PCIE2} },
+ {0x16, {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, SATA1, SATA2} },
+ {0x01, {PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1} },
+ {0x29, {SRIO2, SRIO2, SRIO2, SRIO2, SRIO1, SRIO1, SRIO1, SRIO1} },
+ {0x2D, {SRIO2, SRIO2, SRIO2, SRIO2, SRIO1, SRIO1, SRIO1, SRIO1} },
+ {0x15, {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, SATA1, SATA2} },
+ {0x18, {PCIE1, PCIE1, PCIE1, PCIE1, AURORA, AURORA, SATA1, SATA2} },
+ {0x02, {PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1} },
+ {0x36, {SRIO2, SRIO2, SRIO2, SRIO2, AURORA, AURORA, SATA1, SATA2} },
+ {}
+};
+#endif
+
+static const struct serdes_config *serdes_cfg_tbl[] = {
+ serdes1_cfg_tbl,
+#ifndef CONFIG_PPC_T2081
+ serdes2_cfg_tbl,
+#endif
+};
+
+enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane)
+{
+ const struct serdes_config *ptr;
+
+ if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+ return 0;
+
+ ptr = serdes_cfg_tbl[serdes];
+ while (ptr->protocol) {
+ if (ptr->protocol == cfg)
+ return ptr->lanes[lane];
+ ptr++;
+ }
+ return 0;
+}
+
+int is_serdes_prtcl_valid(int serdes, u32 prtcl)
+{
+ int i;
+ const struct serdes_config *ptr;
+
+ if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+ return 0;
+
+ ptr = serdes_cfg_tbl[serdes];
+ while (ptr->protocol) {
+ if (ptr->protocol == prtcl)
+ break;
+ ptr++;
+ }
+
+ if (!ptr->protocol)
+ return 0;
+
+ for (i = 0; i < SRDS_MAX_LANES; i++) {
+ if (ptr->lanes[i] != NONE)
+ return 1;
+ }
+
+ return 0;
+}
obj-y += cpu.o
obj-y += cpu_init.o
-# 8610 & 8641 are identical w/regards to DDR
-obj-$(CONFIG_MPC8610) += ddr-8641.o
-obj-$(CONFIG_MPC8641) += ddr-8641.o
obj-$(CONFIG_OF_LIBFDT) += fdt.o
obj-y += interrupts.o
obj-$(CONFIG_MP) += mp.o
endif
obj-$(CONFIG_OF_LIBFDT) += fdt.o
-obj-$(CONFIG_FSL_IFC) += fsl_ifc.o
obj-$(CONFIG_FSL_LBC) += fsl_lbc.o
obj-$(CONFIG_SYS_SRIO) += srio.o
obj-$(CONFIG_FSL_LAW) += law.o
endif
-
-ifdef CONFIG_SPL_BUILD
-obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/
-else
-obj-y += ddr/
-endif
CPU_TYPE_ENTRY(T1020, T1020, 0),
CPU_TYPE_ENTRY(T1021, T1021, 0),
CPU_TYPE_ENTRY(T1022, T1022, 0),
+ CPU_TYPE_ENTRY(T2080, T2080, 0),
+ CPU_TYPE_ENTRY(T2081, T2081, 0),
CPU_TYPE_ENTRY(BSC9130, 9130, 1),
CPU_TYPE_ENTRY(BSC9131, 9131, 1),
CPU_TYPE_ENTRY(BSC9132, 9132, 2),
+++ /dev/null
-#
-# Copyright 2008-2011 Freescale Semiconductor, Inc.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License
-# Version 2 as published by the Free Software Foundation.
-#
-
-obj-$(CONFIG_FSL_DDR1) += main.o util.o ctrl_regs.o options.o \
- lc_common_dimm_params.o
-
-obj-$(CONFIG_FSL_DDR2) += main.o util.o ctrl_regs.o options.o \
- lc_common_dimm_params.o
-
-obj-$(CONFIG_FSL_DDR3) += main.o util.o ctrl_regs.o options.o \
- lc_common_dimm_params.o
-ifdef CONFIG_DDR_SPD
-SPD := y
-endif
-ifdef CONFIG_SPD_EEPROM
-SPD := y
-endif
-ifdef SPD
-obj-$(CONFIG_FSL_DDR1) += ddr1_dimm_params.o
-obj-$(CONFIG_FSL_DDR2) += ddr2_dimm_params.o
-obj-$(CONFIG_FSL_DDR3) += ddr3_dimm_params.o
-endif
-
-obj-$(CONFIG_FSL_DDR_INTERACTIVE) += interactive.o
#ifdef CONFIG_MPC85xx
#include <asm/config_mpc85xx.h>
+#define CONFIG_SYS_FSL_DDR
#endif
#ifdef CONFIG_MPC86xx
#include <asm/config_mpc86xx.h>
+#define CONFIG_SYS_FSL_DDR
+#endif
+
+#ifdef CONFIG_MPC83xx
+#define CONFIG_SYS_FSL_DDR
#endif
#ifndef HWCONFIG_BUFFER_SIZE
#elif defined(CONFIG_MPC8540)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 8
+#define CONFIG_SYS_FSL_DDRC_GEN1
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8541)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 8
+#define CONFIG_SYS_FSL_DDRC_GEN1
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8544)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 10
+#define CONFIG_SYS_FSL_DDRC_GEN2
#define CONFIG_SYS_PPC_E500_DEBUG_TLB 0
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8548)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 10
+#define CONFIG_SYS_FSL_DDRC_GEN2
#define CONFIG_SYS_PPC_E500_DEBUG_TLB 0
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8555)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 8
+#define CONFIG_SYS_FSL_DDRC_GEN1
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8560)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 8
+#define CONFIG_SYS_FSL_DDRC_GEN1
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000
#elif defined(CONFIG_MPC8568)
#define CONFIG_MAX_CPUS 1
#define CONFIG_SYS_FSL_NUM_LAWS 10
+#define CONFIG_SYS_FSL_DDRC_GEN2
#define CONFIG_SYS_FSL_SEC_COMPAT 2
#define QE_MURAM_SIZE 0x10000UL
#define MAX_QE_RISC 2
#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
+#elif defined(CONFIG_PPC_T2080) || defined(CONFIG_PPC_T2081)
+#define CONFIG_E6500
+#define CONFIG_SYS_PPC64 /* 64-bit core */
+#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
+#define CONFIG_SYS_FSL_QORIQ_CHASSIS2 /* Freescale Chassis generation 2 */
+#define CONFIG_SYS_FSL_CORES_PER_CLUSTER 4
+#define CONFIG_SYS_FSL_NUM_CC_PLLS 2
+#define CONFIG_SYS_FSL_QMAN_V3
+#define CONFIG_MAX_CPUS 4
+#define CONFIG_SYS_FSL_NUM_LAWS 32
+#define CONFIG_SYS_FSL_SEC_COMPAT 4
+#define CONFIG_SYS_NUM_FMAN 1
+#define CONFIG_SYS_FSL_CLUSTER_CLOCKS { 1, 4, 4, 4 }
+#define CONFIG_SYS_FSL_SRDS_1
+#define CONFIG_SYS_FSL_PCI_VER_3_X
+#if defined(CONFIG_PPC_T2080)
+#define CONFIG_SYS_NUM_FM1_DTSEC 8
+#define CONFIG_SYS_NUM_FM1_10GEC 4
+#define CONFIG_SYS_FSL_SRDS_2
+#define CONFIG_SYS_FSL_SRIO_LIODN
+#define CONFIG_SYS_FSL_SRIO_MAX_PORTS 2
+#define CONFIG_SYS_FSL_SRIO_OB_WIN_NUM 9
+#define CONFIG_SYS_FSL_SRIO_IB_WIN_NUM 5
+#elif defined(CONFIG_PPC_T2081)
+#define CONFIG_SYS_NUM_FM1_DTSEC 6
+#define CONFIG_SYS_NUM_FM1_10GEC 2
+#endif
+#define CONFIG_SYS_FSL_NUM_USB_CTRLS 2
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_PME_PLAT_CLK_DIV 1
+#define CONFIG_SYS_PME_CLK CONFIG_PME_PLAT_CLK_DIV
+#define CONFIG_SYS_FM1_CLK 0
+#define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_4_7
+#define CONFIG_SYS_FSL_IFC_BANK_COUNT 8
+#define CONFIG_SYS_FMAN_V3
+#define CONFIG_SYS_FM_MURAM_SIZE 0x28000
+#define CONFIG_SYS_FSL_TBCLK_DIV 16
+#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v3.0"
+#define CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
+#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
+#define CONFIG_SYS_FSL_SFP_VER_3_0
+#define CONFIG_SYS_FSL_ISBC_VER 2
+
#elif defined(CONFIG_PPC_C29X)
#define CONFIG_MAX_CPUS 1
#define CONFIG_FSL_SDHC_V2_3
#define CONFIG_SYS_FSL_THREADS_PER_CORE 1
#endif
+#if !defined(CONFIG_SYS_FSL_DDRC_GEN1) && \
+ !defined(CONFIG_SYS_FSL_DDRC_GEN2) && \
+ !defined(CONFIG_SYS_FSL_DDRC_GEN3)
+#define CONFIG_SYS_FSL_DDRC_GEN3
+#endif
+
#endif /* _ASM_MPC85xx_CONFIG_H_ */
#ifndef _ASM_MPC86xx_CONFIG_H_
#define _ASM_MPC86xx_CONFIG_H_
+#define CONFIG_SYS_FSL_DDR_86XX
+
/* SoC specific defines for Freescale MPC86xx processors */
#if defined(CONFIG_MPC8610)
QSGMII_FM1_B, /* B indicates MACs 5,6,9,10 */
QSGMII_FM2_A,
QSGMII_FM2_B,
+ XFI_FM1_MAC1,
+ XFI_FM1_MAC2,
XFI_FM1_MAC9,
XFI_FM1_MAC10,
XFI_FM2_MAC9,
#ifndef __IMMAP_83xx__
#define __IMMAP_83xx__
+#include <fsl_immap.h>
#include <asm/types.h>
#include <asm/fsl_i2c.h>
#include <asm/mpc8xxx_spi.h>
} qesba83xx_t;
/*
- * DDR Memory Controller Memory Map
+ * DDR Memory Controller Memory Map for DDR1
+ * The structure of DDR2, or DDR3 is defined in fsl_immap.h
*/
-#if defined(CONFIG_FSL_DDR2) || defined(CONFIG_FSL_DDR3)
-typedef struct ccsr_ddr {
- u32 cs0_bnds; /* Chip Select 0 Memory Bounds */
- u8 res1[4];
- u32 cs1_bnds; /* Chip Select 1 Memory Bounds */
- u8 res2[4];
- u32 cs2_bnds; /* Chip Select 2 Memory Bounds */
- u8 res3[4];
- u32 cs3_bnds; /* Chip Select 3 Memory Bounds */
- u8 res4[100];
- u32 cs0_config; /* Chip Select Configuration */
- u32 cs1_config; /* Chip Select Configuration */
- u32 cs2_config; /* Chip Select Configuration */
- u32 cs3_config; /* Chip Select Configuration */
- u8 res4a[48];
- u32 cs0_config_2; /* Chip Select Configuration 2 */
- u32 cs1_config_2; /* Chip Select Configuration 2 */
- u32 cs2_config_2; /* Chip Select Configuration 2 */
- u32 cs3_config_2; /* Chip Select Configuration 2 */
- u8 res5[48];
- u32 timing_cfg_3; /* SDRAM Timing Configuration 3 */
- u32 timing_cfg_0; /* SDRAM Timing Configuration 0 */
- u32 timing_cfg_1; /* SDRAM Timing Configuration 1 */
- u32 timing_cfg_2; /* SDRAM Timing Configuration 2 */
- u32 sdram_cfg; /* SDRAM Control Configuration */
- u32 sdram_cfg_2; /* SDRAM Control Configuration 2 */
- u32 sdram_mode; /* SDRAM Mode Configuration */
- u32 sdram_mode_2; /* SDRAM Mode Configuration 2 */
- u32 sdram_md_cntl; /* SDRAM Mode Control */
- u32 sdram_interval; /* SDRAM Interval Configuration */
- u32 sdram_data_init; /* SDRAM Data initialization */
- u8 res6[4];
- u32 sdram_clk_cntl; /* SDRAM Clock Control */
- u8 res7[20];
- u32 init_addr; /* training init addr */
- u32 init_ext_addr; /* training init extended addr */
- u8 res8_1[16];
- u32 timing_cfg_4; /* SDRAM Timing Configuration 4 */
- u32 timing_cfg_5; /* SDRAM Timing Configuration 5 */
- u8 reg8_1a[8];
- u32 ddr_zq_cntl; /* ZQ calibration control*/
- u32 ddr_wrlvl_cntl; /* write leveling control*/
- u8 reg8_1aa[4];
- u32 ddr_sr_cntr; /* self refresh counter */
- u32 ddr_sdram_rcw_1; /* Control Words 1 */
- u32 ddr_sdram_rcw_2; /* Control Words 2 */
- u8 reg_1ab[8];
- u32 ddr_wrlvl_cntl_2; /* write leveling control 2 */
- u32 ddr_wrlvl_cntl_3; /* write leveling control 3 */
- u8 res8_1b[104];
- u32 sdram_mode_3; /* SDRAM Mode Configuration 3 */
- u32 sdram_mode_4; /* SDRAM Mode Configuration 4 */
- u32 sdram_mode_5; /* SDRAM Mode Configuration 5 */
- u32 sdram_mode_6; /* SDRAM Mode Configuration 6 */
- u32 sdram_mode_7; /* SDRAM Mode Configuration 7 */
- u32 sdram_mode_8; /* SDRAM Mode Configuration 8 */
- u8 res8_1ba[0x908];
- u32 ddr_dsr1; /* Debug Status 1 */
- u32 ddr_dsr2; /* Debug Status 2 */
- u32 ddr_cdr1; /* Control Driver 1 */
- u32 ddr_cdr2; /* Control Driver 2 */
- u8 res8_1c[200];
- u32 ip_rev1; /* IP Block Revision 1 */
- u32 ip_rev2; /* IP Block Revision 2 */
- u32 eor; /* Enhanced Optimization Register */
- u8 res8_2[252];
- u32 mtcr; /* Memory Test Control Register */
- u8 res8_3[28];
- u32 mtp1; /* Memory Test Pattern 1 */
- u32 mtp2; /* Memory Test Pattern 2 */
- u32 mtp3; /* Memory Test Pattern 3 */
- u32 mtp4; /* Memory Test Pattern 4 */
- u32 mtp5; /* Memory Test Pattern 5 */
- u32 mtp6; /* Memory Test Pattern 6 */
- u32 mtp7; /* Memory Test Pattern 7 */
- u32 mtp8; /* Memory Test Pattern 8 */
- u32 mtp9; /* Memory Test Pattern 9 */
- u32 mtp10; /* Memory Test Pattern 10 */
- u8 res8_4[184];
- u32 data_err_inject_hi; /* Data Path Err Injection Mask High */
- u32 data_err_inject_lo; /* Data Path Err Injection Mask Low */
- u32 ecc_err_inject; /* Data Path Err Injection Mask ECC */
- u8 res9[20];
- u32 capture_data_hi; /* Data Path Read Capture High */
- u32 capture_data_lo; /* Data Path Read Capture Low */
- u32 capture_ecc; /* Data Path Read Capture ECC */
- u8 res10[20];
- u32 err_detect; /* Error Detect */
- u32 err_disable; /* Error Disable */
- u32 err_int_en;
- u32 capture_attributes; /* Error Attrs Capture */
- u32 capture_address; /* Error Addr Capture */
- u32 capture_ext_address; /* Error Extended Addr Capture */
- u32 err_sbe; /* Single-Bit ECC Error Management */
- u8 res11[164];
- u32 debug[32]; /* debug_1 to debug_32 */
- u8 res12[128];
-} ccsr_ddr_t;
-#else
+#if !defined(CONFIG_SYS_FSL_DDR2) && !defined(CONFIG_SYS_FSL_DDR3)
typedef struct ddr_cs_bnds {
u32 csbnds;
u8 res0[4];
u8 dll_ddr[0x100];
u8 dll_lbc[0x100];
u8 res1[0xE00];
-#if defined(CONFIG_FSL_DDR2) || defined(CONFIG_FSL_DDR3)
- ccsr_ddr_t ddr; /* DDR Memory Controller Memory */
+#if defined(CONFIG_SYS_FSL_DDR2) || defined(CONFIG_SYS_FSL_DDR3)
+ struct ccsr_ddr ddr; /* DDR Memory Controller Memory */
#else
ddr83xx_t ddr; /* DDR Memory Controller Memory */
#endif
#endif
#define CONFIG_SYS_MPC8xxx_DDR_OFFSET (0x2000)
-#define CONFIG_SYS_MPC8xxx_DDR_ADDR \
+#define CONFIG_SYS_FSL_DDR_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR_OFFSET)
#define CONFIG_SYS_MPC83xx_DMA_OFFSET (0x8000)
#define CONFIG_SYS_MPC83xx_DMA_ADDR \
#include <asm/types.h>
#include <asm/fsl_dma.h>
#include <asm/fsl_i2c.h>
-#include <asm/fsl_ifc.h>
+#include <fsl_ifc.h>
#include <asm/fsl_lbc.h>
#include <asm/fsl_fman.h>
+#include <fsl_immap.h>
typedef struct ccsr_local {
u32 ccsrbarh; /* CCSR Base Addr High */
u8 res24[492];
} ccsr_local_ecm_t;
-/* DDR memory controller registers */
-typedef struct ccsr_ddr {
- u32 cs0_bnds; /* Chip Select 0 Memory Bounds */
- u8 res1[4];
- u32 cs1_bnds; /* Chip Select 1 Memory Bounds */
- u8 res2[4];
- u32 cs2_bnds; /* Chip Select 2 Memory Bounds */
- u8 res3[4];
- u32 cs3_bnds; /* Chip Select 3 Memory Bounds */
- u8 res4[100];
- u32 cs0_config; /* Chip Select Configuration */
- u32 cs1_config; /* Chip Select Configuration */
- u32 cs2_config; /* Chip Select Configuration */
- u32 cs3_config; /* Chip Select Configuration */
- u8 res4a[48];
- u32 cs0_config_2; /* Chip Select Configuration 2 */
- u32 cs1_config_2; /* Chip Select Configuration 2 */
- u32 cs2_config_2; /* Chip Select Configuration 2 */
- u32 cs3_config_2; /* Chip Select Configuration 2 */
- u8 res5[48];
- u32 timing_cfg_3; /* SDRAM Timing Configuration 3 */
- u32 timing_cfg_0; /* SDRAM Timing Configuration 0 */
- u32 timing_cfg_1; /* SDRAM Timing Configuration 1 */
- u32 timing_cfg_2; /* SDRAM Timing Configuration 2 */
- u32 sdram_cfg; /* SDRAM Control Configuration */
- u32 sdram_cfg_2; /* SDRAM Control Configuration 2 */
- u32 sdram_mode; /* SDRAM Mode Configuration */
- u32 sdram_mode_2; /* SDRAM Mode Configuration 2 */
- u32 sdram_md_cntl; /* SDRAM Mode Control */
- u32 sdram_interval; /* SDRAM Interval Configuration */
- u32 sdram_data_init; /* SDRAM Data initialization */
- u8 res6[4];
- u32 sdram_clk_cntl; /* SDRAM Clock Control */
- u8 res7[20];
- u32 init_addr; /* training init addr */
- u32 init_ext_addr; /* training init extended addr */
- u8 res8_1[16];
- u32 timing_cfg_4; /* SDRAM Timing Configuration 4 */
- u32 timing_cfg_5; /* SDRAM Timing Configuration 5 */
- u8 reg8_1a[8];
- u32 ddr_zq_cntl; /* ZQ calibration control*/
- u32 ddr_wrlvl_cntl; /* write leveling control*/
- u8 reg8_1aa[4];
- u32 ddr_sr_cntr; /* self refresh counter */
- u32 ddr_sdram_rcw_1; /* Control Words 1 */
- u32 ddr_sdram_rcw_2; /* Control Words 2 */
- u8 reg_1ab[8];
- u32 ddr_wrlvl_cntl_2; /* write leveling control 2 */
- u32 ddr_wrlvl_cntl_3; /* write leveling control 3 */
- u8 res8_1b[104];
- u32 sdram_mode_3; /* SDRAM Mode Configuration 3 */
- u32 sdram_mode_4; /* SDRAM Mode Configuration 4 */
- u32 sdram_mode_5; /* SDRAM Mode Configuration 5 */
- u32 sdram_mode_6; /* SDRAM Mode Configuration 6 */
- u32 sdram_mode_7; /* SDRAM Mode Configuration 7 */
- u32 sdram_mode_8; /* SDRAM Mode Configuration 8 */
- u8 res8_1ba[0x908];
- u32 ddr_dsr1; /* Debug Status 1 */
- u32 ddr_dsr2; /* Debug Status 2 */
- u32 ddr_cdr1; /* Control Driver 1 */
- u32 ddr_cdr2; /* Control Driver 2 */
- u8 res8_1c[200];
- u32 ip_rev1; /* IP Block Revision 1 */
- u32 ip_rev2; /* IP Block Revision 2 */
- u32 eor; /* Enhanced Optimization Register */
- u8 res8_2[252];
- u32 mtcr; /* Memory Test Control Register */
- u8 res8_3[28];
- u32 mtp1; /* Memory Test Pattern 1 */
- u32 mtp2; /* Memory Test Pattern 2 */
- u32 mtp3; /* Memory Test Pattern 3 */
- u32 mtp4; /* Memory Test Pattern 4 */
- u32 mtp5; /* Memory Test Pattern 5 */
- u32 mtp6; /* Memory Test Pattern 6 */
- u32 mtp7; /* Memory Test Pattern 7 */
- u32 mtp8; /* Memory Test Pattern 8 */
- u32 mtp9; /* Memory Test Pattern 9 */
- u32 mtp10; /* Memory Test Pattern 10 */
- u8 res8_4[184];
- u32 data_err_inject_hi; /* Data Path Err Injection Mask High */
- u32 data_err_inject_lo; /* Data Path Err Injection Mask Low */
- u32 ecc_err_inject; /* Data Path Err Injection Mask ECC */
- u8 res9[20];
- u32 capture_data_hi; /* Data Path Read Capture High */
- u32 capture_data_lo; /* Data Path Read Capture Low */
- u32 capture_ecc; /* Data Path Read Capture ECC */
- u8 res10[20];
- u32 err_detect; /* Error Detect */
- u32 err_disable; /* Error Disable */
- u32 err_int_en;
- u32 capture_attributes; /* Error Attrs Capture */
- u32 capture_address; /* Error Addr Capture */
- u32 capture_ext_address; /* Error Extended Addr Capture */
- u32 err_sbe; /* Single-Bit ECC Error Management */
- u8 res11[164];
- u32 debug[32]; /* debug_1 to debug_32 */
- u8 res12[128];
-} ccsr_ddr_t;
-
#define DDR_EOR_RD_BDW_OPT_DIS 0x80000000 /* Read BDW Opt. disable */
#define DDR_EOR_ADDR_HASH_EN 0x40000000 /* Address hash enabled */
#define FSL_CORENET_DEVDISR2_DTSEC1_10 0x00400000
#define FSL_CORENET_DEVDISR2_10GEC1_1 0x00800000
#define FSL_CORENET_DEVDISR2_10GEC1_2 0x00400000
+#define FSL_CORENET_DEVDISR2_10GEC1_3 0x80000000
+#define FSL_CORENET_DEVDISR2_10GEC1_4 0x40000000
#define FSL_CORENET_DEVDISR2_DTSEC2_1 0x00080000
#define FSL_CORENET_DEVDISR2_DTSEC2_2 0x00040000
#define FSL_CORENET_DEVDISR2_DTSEC2_3 0x00020000
#define FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT 24
#define FSL_CORENET2_RCWSR4_SRDS2_PRTCL 0x00fe0000
#define FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT 17
+#elif defined(CONFIG_PPC_T2080) || defined(CONFIG_PPC_T2081)
+#define FSL_CORENET2_RCWSR4_SRDS1_PRTCL 0xff000000
+#define FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT 24
+#define FSL_CORENET2_RCWSR4_SRDS2_PRTCL 0x00ff0000
+#define FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT 16
+#define FSL_CORENET_RCWSR6_BOOT_LOC 0x0f800000
#endif
#define FSL_CORENET2_RCWSR5_SRDS_PLL_PD_S1_PLL1 0x00800000
#define FSL_CORENET2_RCWSR5_SRDS_PLL_PD_S1_PLL2 0x00400000
#define FSL_CORENET_RCWSR13_EC2_FM1_DTSEC5_RGMII 0x00000000
#define FSL_CORENET_RCWSR13_EC2_FM1_DTSEC6_RGMII 0x08000000
#define FSL_CORENET_RCWSR13_EC2_FM1_GPIO 0x10000000
+#endif
+#if defined(CONFIG_PPC_T2080) || defined(CONFIG_PPC_T2081)
+#define FSL_CORENET_RCWSR13_EC1 0x60000000 /* bits 417..418 */
+#define FSL_CORENET_RCWSR13_EC1_DTSEC3_RGMII 0x00000000
+#define FSL_CORENET_RCWSR13_EC1_GPIO 0x40000000
+#define FSL_CORENET_RCWSR13_EC2 0x18000000 /* bits 419..420 */
+#define FSL_CORENET_RCWSR13_EC2_DTSEC4_RGMII 0x00000000
+#define FSL_CORENET_RCWSR13_EC2_DTSEC10_RGMII 0x08000000
+#define FSL_CORENET_RCWSR13_EC2_GPIO 0x10000000
#endif
u8 res18[192];
u32 scratchrw[4]; /* Scratch Read/Write */
#define CONFIG_SYS_FSL_CPC_OFFSET 0x10000
#define CONFIG_SYS_MPC85xx_DMA1_OFFSET 0x100000
#define CONFIG_SYS_MPC85xx_DMA2_OFFSET 0x101000
+#define CONFIG_SYS_MPC85xx_DMA3_OFFSET 0x102000
#define CONFIG_SYS_MPC85xx_DMA_OFFSET CONFIG_SYS_MPC85xx_DMA1_OFFSET
#define CONFIG_SYS_MPC85xx_ESPI_OFFSET 0x110000
#define CONFIG_SYS_MPC85xx_ESDHC_OFFSET 0x114000
(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_CORENET_RCPM_OFFSET)
#define CONFIG_SYS_MPC85xx_ECM_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_ECM_OFFSET)
-#define CONFIG_SYS_MPC8xxx_DDR_ADDR \
+#define CONFIG_SYS_FSL_DDR_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR_OFFSET)
-#define CONFIG_SYS_MPC8xxx_DDR2_ADDR \
+#define CONFIG_SYS_FSL_DDR2_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR2_OFFSET)
-#define CONFIG_SYS_MPC8xxx_DDR3_ADDR \
+#define CONFIG_SYS_FSL_DDR3_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR3_OFFSET)
#define CONFIG_SYS_LBC_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_LBC_OFFSET)
#ifndef __IMMAP_86xx__
#define __IMMAP_86xx__
+#include <fsl_immap.h>
#include <asm/types.h>
#include <asm/fsl_dma.h>
#include <asm/fsl_lbc.h>
char res31[488];
} ccsr_local_mcm_t;
-/* DDR memory controller registers(0x2000-0x3000) and (0x6000-0x7000) */
-
-typedef struct ccsr_ddr {
- uint cs0_bnds; /* 0x2000 - DDR Chip Select 0 Memory Bounds */
- char res1[4];
- uint cs1_bnds; /* 0x2008 - DDR Chip Select 1 Memory Bounds */
- char res2[4];
- uint cs2_bnds; /* 0x2010 - DDR Chip Select 2 Memory Bounds */
- char res3[4];
- uint cs3_bnds; /* 0x2018 - DDR Chip Select 3 Memory Bounds */
- char res4[4];
- uint cs4_bnds; /* 0x2020 - DDR Chip Select 4 Memory Bounds */
- char res5[4];
- uint cs5_bnds; /* 0x2028 - DDR Chip Select 5 Memory Bounds */
- char res6[84];
- uint cs0_config; /* 0x2080 - DDR Chip Select Configuration */
- uint cs1_config; /* 0x2084 - DDR Chip Select Configuration */
- uint cs2_config; /* 0x2088 - DDR Chip Select Configuration */
- uint cs3_config; /* 0x208c - DDR Chip Select Configuration */
- uint cs4_config; /* 0x2090 - DDR Chip Select Configuration */
- uint cs5_config; /* 0x2094 - DDR Chip Select Configuration */
- char res7[104];
- uint timing_cfg_3; /* 0x2100 - DDR SDRAM Timing Configuration Register 3 */
- uint timing_cfg_0; /* 0x2104 - DDR SDRAM Timing Configuration Register 0 */
- uint timing_cfg_1; /* 0x2108 - DDR SDRAM Timing Configuration Register 1 */
- uint timing_cfg_2; /* 0x210c - DDR SDRAM Timing Configuration Register 2 */
- uint sdram_cfg; /* 0x2110 - DDR SDRAM Control Configuration 1 */
- uint sdram_cfg_2; /* 0x2114 - DDR SDRAM Control Configuration 2 */
- uint sdram_mode; /* 0x2118 - DDR SDRAM Mode Configuration 1 */
- uint sdram_mode_2; /* 0x211c - DDR SDRAM Mode Configuration 2 */
- uint sdram_mode_cntl; /* 0x2120 - DDR SDRAM Mode Control */
- uint sdram_interval; /* 0x2124 - DDR SDRAM Interval Configuration */
- uint sdram_data_init; /* 0x2128 - DDR SDRAM Data Initialization */
- char res8[4];
- uint sdram_clk_cntl; /* 0x2130 - DDR SDRAM Clock Control */
- char res9[12];
- uint sdram_ocd_cntl; /* 0x2140 - DDR SDRAM OCD Control */
- uint sdram_ocd_status; /* 0x2144 - DDR SDRAM OCD Status */
- uint init_addr; /* 0x2148 - DDR training initialzation address */
- uint init_ext_addr; /* 0x214C - DDR training initialzation extended address */
- char res10[2728];
- uint ip_rev1; /* 0x2BF8 - DDR IP Block Revision 1 */
- uint ip_rev2; /* 0x2BFC - DDR IP Block Revision 2 */
- char res11[512];
- uint data_err_inject_hi; /* 0x2e00 - DDR Memory Data Path Error Injection Mask High */
- uint data_err_inject_lo; /* 0x2e04 - DDR Memory Data Path Error Injection Mask Low */
- uint ecc_err_inject; /* 0x2e08 - DDR Memory Data Path Error Injection Mask ECC */
- char res12[20];
- uint capture_data_hi; /* 0x2e20 - DDR Memory Data Path Read Capture High */
- uint capture_data_lo; /* 0x2e24 - DDR Memory Data Path Read Capture Low */
- uint capture_ecc; /* 0x2e28 - DDR Memory Data Path Read Capture ECC */
- char res13[20];
- uint err_detect; /* 0x2e40 - DDR Memory Error Detect */
- uint err_disable; /* 0x2e44 - DDR Memory Error Disable */
- uint err_int_en; /* 0x2e48 - DDR Memory Error Interrupt Enable */
- uint capture_attributes; /* 0x2e4c - DDR Memory Error Attributes Capture */
- uint capture_address; /* 0x2e50 - DDR Memory Error Address Capture */
- uint capture_ext_address; /* 0x2e54 - DDR Memory Error Extended Address Capture */
- uint err_sbe; /* 0x2e58 - DDR Memory Single-Bit ECC Error Management */
- char res14[164];
- uint debug_1; /* 0x2f00 */
- uint debug_2;
- uint debug_3;
- uint debug_4;
- uint debug_5;
- char res15[236];
-} ccsr_ddr_t;
-
-
/* Daul I2C Registers(0x3000-0x4000) */
typedef struct ccsr_i2c {
struct fsl_i2c i2c[2];
typedef struct immap {
ccsr_local_mcm_t im_local_mcm;
- ccsr_ddr_t im_ddr1;
+ struct ccsr_ddr im_ddr1;
ccsr_i2c_t im_i2c;
ccsr_duart_t im_duart;
fsl_lbc_t im_lbc;
- ccsr_ddr_t im_ddr2;
+ struct ccsr_ddr im_ddr2;
char res1[4096];
ccsr_pex_t im_pex1;
ccsr_pex_t im_pex2;
extern immap_t *immr;
#define CONFIG_SYS_MPC8xxx_DDR_OFFSET 0x2000
-#define CONFIG_SYS_MPC8xxx_DDR_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR_OFFSET)
+#define CONFIG_SYS_FSL_DDR_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR_OFFSET)
#define CONFIG_SYS_MPC8xxx_DDR2_OFFSET 0x6000
-#define CONFIG_SYS_MPC8xxx_DDR2_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR2_OFFSET)
+#define CONFIG_SYS_FSL_DDR2_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC8xxx_DDR2_OFFSET)
#define CONFIG_SYS_MPC86xx_DMA_OFFSET 0x21000
#define CONFIG_SYS_MPC86xx_DMA_ADDR (CONFIG_SYS_IMMR + CONFIG_SYS_MPC86xx_DMA_OFFSET)
#define CONFIG_SYS_MPC86xx_PIC_OFFSET 0x40000
static inline void mpc85xx_gpio_set(unsigned int mask,
unsigned int dir, unsigned int val)
{
- ccsr_gpio_t *gpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR + 0xc00);
+ ccsr_gpio_t *gpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
/* First mask off the unwanted parts of "dir" and "val" */
dir &= mask;
static inline unsigned int mpc85xx_gpio_get(unsigned int mask)
{
- ccsr_gpio_t *gpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR + 0xc00);
+ ccsr_gpio_t *gpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
/* Read the requested values */
return in_be32(&gpio->gpdat) & mask;
#define SVR_T1020 0x852100
#define SVR_T1021 0x852101
#define SVR_T1022 0x852102
+#define SVR_T2080 0x853000
+#define SVR_T2081 0x853100
#define SVR_8610 0x80A000
#define SVR_8641 0x809000
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <miiphy.h>
#include <libfdt.h>
unsigned int gpio_low = 0;
unsigned int gpio_in = 0;
unsigned int i;
+ struct ccsr_ddr __iomem *ddr;
puts("Board: HWW-1U-1A ");
* and delay a while before we continue.
*/
if (mpc85xx_gpio_get(GPIO_RESETS)) {
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ddr = (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
puts("Debugger detected... extra device reset enabled!\n");
#include <common.h>
#include <i2c.h>
#include <hwconfig.h>
+#include <fsl_ddr.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
-#include <../arch/powerpc/cpu/mpc8xxx/ddr/ddr.h>
DECLARE_GLOBAL_DATA_PTR;
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <nand.h>
#include <linux/compiler.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/global_data.h>
DECLARE_GLOBAL_DATA_PTR;
*/
static void sdram_init(void)
{
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
__raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds);
__raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config);
#include <tsec.h>
#include <mmc.h>
#include <netdev.h>
-#include <asm/fsl_ifc.h>
+#include <fsl_ifc.h>
#include <hwconfig.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#ifdef CONFIG_PCI
#include <pci.h>
*copy the ddr controller settings from PowerPC side DDR controller
*to the DSP DDR controller as connected DDR memories are similar.
*/
- ccsr_ddr_t __iomem *pa_ddr =
- (ccsr_ddr_t __iomem *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
- ccsr_ddr_t temp_ddr;
- ccsr_ddr_t __iomem *dsp_ddr =
- (ccsr_ddr_t __iomem *)CONFIG_SYS_FSL_DSP_CCSR_DDR_ADDR;
+ struct ccsr_ddr __iomem *pa_ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
+ struct ccsr_ddr temp_ddr;
+ struct ccsr_ddr __iomem *dsp_ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DSP_CCSR_DDR_ADDR;
- memcpy(&temp_ddr, pa_ddr, sizeof(ccsr_ddr_t));
+ memcpy(&temp_ddr, pa_ddr, sizeof(struct ccsr_ddr));
temp_ddr.cs0_bnds = CONFIG_SYS_DDR1_CS0_BNDS;
temp_ddr.sdram_cfg &= ~SDRAM_CFG_MEM_EN;
- memcpy(dsp_ddr, &temp_ddr, sizeof(ccsr_ddr_t));
+ memcpy(dsp_ddr, &temp_ddr, sizeof(struct ccsr_ddr));
dsp_ddr->sdram_cfg |= SDRAM_CFG_MEM_EN;
}
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <nand.h>
#include <linux/compiler.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/global_data.h>
DECLARE_GLOBAL_DATA_PTR;
static void sdram_init(void)
{
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
#if CONFIG_DDR_CLK_FREQ == 100000000
__raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds);
__raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config);
#include <mmc.h>
#include <netdev.h>
#include <pci.h>
-#include <asm/fsl_ifc.h>
+#include <fsl_ifc.h>
#include <asm/fsl_pci.h>
#include "cpld.h"
#include <common.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include "cpld.h"
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
DECLARE_GLOBAL_DATA_PTR;
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/fsl_portals.h>
#include <asm/fsl_liodn.h>
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
fixed_ddr_parm_t fixed_ddr_parm_0[] = {
{0, 0, NULL}
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#define CONFIG_SYS_DDR_TIMING_3_1200 0x01030000
#define CONFIG_SYS_DDR_TIMING_0_1200 0xCC550104
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
fixed_ddr_parm_t fixed_ddr_parm_0[] = {
{0, 0, NULL}
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
fixed_ddr_parm_t fixed_ddr_parm_0[] = {
{0, 0, NULL}
obj-y += mpc8349emds.o
obj-$(CONFIG_PCI) += pci.o
-obj-$(CONFIG_FSL_DDR2) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
struct board_specific_parameters {
u32 n_ranks;
#include <i2c.h>
#include <spi.h>
#include <miiphy.h>
-#ifdef CONFIG_FSL_DDR2
-#include <asm/fsl_ddr_sdram.h>
+#ifdef CONFIG_SYS_FSL_DDR2
+#include <fsl_ddr_sdram.h>
#else
#include <spd_sdram.h>
#endif
/* DDR SDRAM - Main SODIMM */
im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_BASE & LAWBAR_BAR;
#if defined(CONFIG_SPD_EEPROM)
-#ifndef CONFIG_FSL_DDR2
+#ifndef CONFIG_SYS_FSL_DDR2
msize = spd_sdram() * 1024 * 1024;
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
ddr_enable_ecc(msize);
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_serdes.h>
#include <spd.h>
phys_size_t fixed_sdram (void)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile ccsr_ddr_t *ddr= &immap->im_ddr;
+ struct ccsr_ddr __iomem *ddr = &immap->im_ddr;
uint d_init;
ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <libfdt.h>
#include <fdt_support.h>
phys_size_t fixed_sdram(void)
{
#ifndef CONFIG_SYS_RAMBOOT
- volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);
ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <ioports.h>
#include <spd_sdram.h>
#include <libfdt.h>
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/io.h>
#include <miiphy.h>
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <miiphy.h>
#include <libfdt.h>
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <ioports.h>
#include <spd_sdram.h>
#include <libfdt.h>
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <ioports.h>
#include <spd_sdram.h>
#include <miiphy.h>
phys_size_t fixed_sdram(void)
{
#ifndef CONFIG_SYS_RAMBOOT
- volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
+ volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_FSL_DDR_ADDR);
ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <spd_sdram.h>
#include <i2c.h>
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/io.h>
#include <spd_sdram.h>
#if !defined(CONFIG_SPD_EEPROM)
phys_size_t fixed_sdram(void)
{
- volatile ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
uint d_init;
out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS);
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
struct board_specific_parameters {
u32 n_ranks;
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_serdes.h>
#include <miiphy.h>
phys_size_t fixed_sdram (void)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile ccsr_ddr_t *ddr= &immap->im_ddr;
+ struct ccsr_ddr __iomem *ddr = &immap->im_ddr;
uint d_init;
ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
#
obj-y += mpc8610hpcd.o
-obj-$(CONFIG_FSL_DDR2) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
obj-y += law.o
obj-$(CONFIG_FSL_DIU_FB) += mpc8610hpcd_diu.o
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/immap_86xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <i2c.h>
#include <asm/io.h>
{
#if !defined(CONFIG_SYS_RAMBOOT)
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile ccsr_ddr_t *ddr = &immap->im_ddr1;
+ struct ccsr_ddr __iomem *ddr = &immap->im_ddr1;
uint d_init;
ddr->cs0_bnds = 0x0000001f;
obj-y += mpc8641hpcn.o
obj-y += law.o
-obj-$(CONFIG_FSL_DDR2) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
struct board_specific_parameters {
u32 n_ranks;
#include <asm/processor.h>
#include <asm/immap_86xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/io.h>
#include <libfdt.h>
{
#if !defined(CONFIG_SYS_RAMBOOT)
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile ccsr_ddr_t *ddr = &immap->im_ddr1;
+ struct ccsr_ddr __iomem *ddr = &immap->im_ddr1;
ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <netdev.h>
#include <pci.h>
#include <asm/fsl_serdes.h>
-#include <asm/fsl_ifc.h>
+#include <fsl_ifc.h>
#include <asm/fsl_pci.h>
#include <hwconfig.h>
#include <i2c.h>
#include <nand.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_law.h>
#include <asm/global_data.h>
void sdram_init(void)
{
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
u32 ddr_ratio;
unsigned long ddr_freq_mhz;
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
struct board_specific_parameters {
u32 n_ranks;
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/io.h>
#include <libfdt.h>
#include <asm/io.h>
#include <nand.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
const static u32 sysclk_tbl[] = {
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_portals.h>
#include <libfdt.h>
#include <fdt_support.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_portals.h>
#include <libfdt.h>
#include <fdt_support.h>
phys_size_t fixed_sdram(void)
{
#ifndef CONFIG_SYS_RAMBOOT
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1);
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <asm/fsl_lbc.h>
#include <nand.h>
#include <linux/compiler.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/global_data.h>
DECLARE_GLOBAL_DATA_PTR;
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_law.h>
#include <asm/fsl_lbc.h>
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
struct board_specific_parameters {
u32 n_ranks;
* num| hi| clk| cpo|wrdata|2T
* ranks| mhz|adjst| | delay|
*/
-#ifdef CONFIG_FSL_DDR2
+#ifdef CONFIG_SYS_FSL_DDR2
{2, 549, 4, 0x1f, 2, 0},
{2, 680, 4, 0x1f, 3, 0},
{2, 850, 4, 0x1f, 4, 0},
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/io.h>
#include <asm/fsl_serdes.h>
#include <miiphy.h>
phys_size_t fixed_sdram(void)
{
- volatile ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
uint d_init;
ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
struct board_specific_parameters {
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
#include "ddr.h"
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
#include "ddr.h"
--- /dev/null
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-$(CONFIG_T2080QDS) += t2080qds.o
+obj-$(CONFIG_T2080QDS) += eth_t2080qds.o
+obj-$(CONFIG_PCI) += pci.o
+obj-y += ddr.o
+obj-y += law.o
+obj-y += tlb.o
--- /dev/null
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 or later as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+#include "ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+
+ if (ctrl_num > 2) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ /*
+ * we use identical timing for all slots. If needed, change the code
+ * to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
+ */
+ if (popts->registered_dimm_en)
+ pbsp = rdimms[0];
+ else
+ pbsp = udimms[0];
+
+
+ /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks &&
+ (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay =
+ pbsp->write_data_delay;
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ popts->twot_en = pbsp->force_2t;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found");
+ printf("for data rate %lu MT/s\n", ddr_freq);
+ printf("Trying to use the highest speed (%u) parameters\n",
+ pbsp_highest->datarate_mhz_high);
+ popts->cpo_override = pbsp_highest->cpo;
+ popts->write_data_delay = pbsp_highest->write_data_delay;
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ popts->twot_en = pbsp_highest->force_2t;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
+ "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, "
+ "wrlvl_ctrl_3 0x%x\n",
+ pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
+ pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
+ pbsp->wrlvl_ctl_3);
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * Rtt and Rtt_WR override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 75 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+ puts("Initializing....using SPD\n");
+
+ dram_size = fsl_ddr_sdram();
+
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+
+ puts(" DDR: ");
+ return dram_size;
+}
--- /dev/null
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+ u32 cpo;
+ u32 write_data_delay;
+ u32 force_2t;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
+ */
+ {2, 1350, 4, 4, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0},
+ {2, 1350, 0, 5, 7, 0x0709090b, 0x0c0c0d09, 0xff, 2, 0},
+ {2, 1666, 4, 4, 8, 0x080a0a0d, 0x0d10100b, 0xff, 2, 0},
+ {2, 1666, 0, 5, 7, 0x080a0a0c, 0x0d0d0e0a, 0xff, 2, 0},
+ {2, 1900, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0},
+ {2, 2140, 0, 4, 8, 0x090a0b0e, 0x0f11120c, 0xff, 2, 0},
+ {1, 1350, 0, 5, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0},
+ {1, 1700, 0, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0},
+ {1, 1800, 2, 5, 6, 0x06070709, 0x110a0b08, 0xff, 2, 0},
+ {1, 1866, 2, 4, 6, 0x06060708, 0x09090a07, 0xff, 2, 0},
+ {1, 1900, 2, 4, 6, 0x06060708, 0x09090a07, 0xff, 2, 0},
+ {1, 2000, 2, 4, 8, 0x090a0b0d, 0x0e0f110b, 0xff, 2, 0},
+ {1, 2133, 2, 4, 8, 0x090a0b0d, 0x0e0f110b, 0xff, 2, 0},
+ {}
+};
+
+static const struct board_specific_parameters rdimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
+ */
+ {4, 1350, 0, 5, 9, 0x08070605, 0x06070806, 0xff, 2, 0},
+ {4, 1666, 0, 5, 11, 0x0a080706, 0x07090906, 0xff, 2, 0},
+ {4, 2140, 0, 5, 12, 0x0b090807, 0x080a0b07, 0xff, 2, 0},
+ {2, 1350, 0, 5, 9, 0x08070605, 0x06070806, 0xff, 2, 0},
+ {2, 1666, 0, 5, 11, 0x0a090806, 0x08090a06, 0xff, 2, 0},
+ {2, 2140, 0, 5, 12, 0x0b090807, 0x080a0b07, 0xff, 2, 0},
+ {1, 1350, 0, 5, 9, 0x08070605, 0x06070806, 0xff, 2, 0},
+ {1, 1666, 0, 5, 11, 0x0a090806, 0x08090a06, 0xff, 2, 0},
+ {1, 2140, 0, 4, 12, 0x0b090807, 0x080a0b07, 0xff, 2, 0},
+ {}
+};
+
+/*
+ * The three slots have slightly different timing. The center values are good
+ * for all slots. We use identical speed tables for them. In future use, if
+ * DIMMs require separated tables, make more entries as needed.
+ */
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+};
+
+/*
+ * The three slots have slightly different timing. See comments above.
+ */
+static const struct board_specific_parameters *rdimms[] = {
+ rdimm0,
+};
+
+
+#endif
--- /dev/null
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * Shengzhou Liu <Shengzhou.Liu@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <asm/fsl_dtsec.h>
+#include <asm/fsl_serdes.h>
+#include "../common/qixis.h"
+#include "../common/fman.h"
+#include "t2080qds_qixis.h"
+
+#define EMI_NONE 0xFFFFFFFF
+#define EMI1_RGMII1 0
+#define EMI1_RGMII2 1
+#define EMI1_SLOT1 2
+#define EMI1_SLOT2 6
+#define EMI1_SLOT3 3
+#define EMI1_SLOT4 4
+#define EMI1_SLOT5 5
+#define EMI2 7
+
+static int mdio_mux[NUM_FM_PORTS];
+
+static const char * const mdio_names[] = {
+ "T2080QDS_MDIO_RGMII1",
+ "T2080QDS_MDIO_RGMII2",
+ "T2080QDS_MDIO_SLOT1",
+ "T2080QDS_MDIO_SLOT3",
+ "T2080QDS_MDIO_SLOT4",
+ "T2080QDS_MDIO_SLOT5",
+ "T2080QDS_MDIO_SLOT2",
+ "T2080QDS_MDIO_10GC",
+};
+
+/* Map SerDes1 8 lanes to default slot, will be initialized dynamically */
+static u8 lane_to_slot[] = {3, 3, 3, 3, 1, 1, 1, 1};
+
+static const char *T2080qds_mdio_name_for_muxval(u8 muxval)
+{
+ return mdio_names[muxval];
+}
+
+struct mii_dev *mii_dev_for_muxval(u8 muxval)
+{
+ struct mii_dev *bus;
+ const char *name = T2080qds_mdio_name_for_muxval(muxval);
+
+ if (!name) {
+ printf("No bus for muxval %x\n", muxval);
+ return NULL;
+ }
+
+ bus = miiphy_get_dev_by_name(name);
+
+ if (!bus) {
+ printf("No bus by name %s\n", name);
+ return NULL;
+ }
+
+ return bus;
+}
+
+struct T2080qds_mdio {
+ u8 muxval;
+ struct mii_dev *realbus;
+};
+
+static void T2080qds_mux_mdio(u8 muxval)
+{
+ u8 brdcfg4;
+ if (muxval < 7) {
+ brdcfg4 = QIXIS_READ(brdcfg[4]);
+ brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
+ brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
+ QIXIS_WRITE(brdcfg[4], brdcfg4);
+ }
+}
+
+static int T2080qds_mdio_read(struct mii_dev *bus, int addr, int devad,
+ int regnum)
+{
+ struct T2080qds_mdio *priv = bus->priv;
+
+ T2080qds_mux_mdio(priv->muxval);
+
+ return priv->realbus->read(priv->realbus, addr, devad, regnum);
+}
+
+static int T2080qds_mdio_write(struct mii_dev *bus, int addr, int devad,
+ int regnum, u16 value)
+{
+ struct T2080qds_mdio *priv = bus->priv;
+
+ T2080qds_mux_mdio(priv->muxval);
+
+ return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
+}
+
+static int T2080qds_mdio_reset(struct mii_dev *bus)
+{
+ struct T2080qds_mdio *priv = bus->priv;
+
+ return priv->realbus->reset(priv->realbus);
+}
+
+static int T2080qds_mdio_init(char *realbusname, u8 muxval)
+{
+ struct T2080qds_mdio *pmdio;
+ struct mii_dev *bus = mdio_alloc();
+
+ if (!bus) {
+ printf("Failed to allocate T2080QDS MDIO bus\n");
+ return -1;
+ }
+
+ pmdio = malloc(sizeof(*pmdio));
+ if (!pmdio) {
+ printf("Failed to allocate T2080QDS private data\n");
+ free(bus);
+ return -1;
+ }
+
+ bus->read = T2080qds_mdio_read;
+ bus->write = T2080qds_mdio_write;
+ bus->reset = T2080qds_mdio_reset;
+ sprintf(bus->name, T2080qds_mdio_name_for_muxval(muxval));
+
+ pmdio->realbus = miiphy_get_dev_by_name(realbusname);
+
+ if (!pmdio->realbus) {
+ printf("No bus with name %s\n", realbusname);
+ free(bus);
+ free(pmdio);
+ return -1;
+ }
+
+ pmdio->muxval = muxval;
+ bus->priv = pmdio;
+
+ return mdio_register(bus);
+}
+
+void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
+ enum fm_port port, int offset)
+{
+ int phy;
+ char alias[20];
+ struct fixed_link f_link;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+
+ srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
+ phy = fm_info_get_phy_address(port);
+ switch (port) {
+ case FM1_DTSEC1:
+ case FM1_DTSEC2:
+ case FM1_DTSEC9:
+ case FM1_DTSEC10:
+ sprintf(alias, "phy_sgmii_s3_%x", phy);
+ fdt_set_phy_handle(fdt, compat, addr, alias);
+ fdt_status_okay_by_alias(fdt, "emi1_slot3");
+ break;
+ case FM1_DTSEC5:
+ case FM1_DTSEC6:
+ if (mdio_mux[port] == EMI1_SLOT1) {
+ sprintf(alias, "phy_sgmii_s1_%x", phy);
+ fdt_set_phy_handle(fdt, compat, addr, alias);
+ fdt_status_okay_by_alias(fdt, "emi1_slot1");
+ } else if (mdio_mux[port] == EMI1_SLOT2) {
+ sprintf(alias, "phy_sgmii_s2_%x", phy);
+ fdt_set_phy_handle(fdt, compat, addr, alias);
+ fdt_status_okay_by_alias(fdt, "emi1_slot2");
+ }
+ break;
+ default:
+ break;
+ }
+
+ } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) {
+ switch (srds_s1) {
+ case 0x66: /* XFI interface */
+ case 0x6b:
+ case 0x6c:
+ case 0x6d:
+ case 0x71:
+ f_link.phy_id = port;
+ f_link.duplex = 1;
+ f_link.link_speed = 10000;
+ f_link.pause = 0;
+ f_link.asym_pause = 0;
+ /* no PHY for XFI */
+ fdt_delprop(fdt, offset, "phy-handle");
+ fdt_setprop(fdt, offset, "fixed-link", &f_link,
+ sizeof(f_link));
+ break;
+ default:
+ break;
+ }
+ }
+}
+
+void fdt_fixup_board_enet(void *fdt)
+{
+ return;
+}
+
+/*
+ * This function reads RCW to check if Serdes1{E,F,G,H} is configured
+ * as slot 1/2/3 and update the lane_to_slot[] array accordingly
+ */
+static void initialize_lane_to_slot(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+
+ srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ switch (srds_s1) {
+ case 0x51:
+ case 0x5f:
+ case 0x65:
+ case 0x6b:
+ case 0x71:
+ lane_to_slot[5] = 2;
+ lane_to_slot[6] = 2;
+ lane_to_slot[7] = 2;
+ break;
+ case 0xa6:
+ case 0x8e:
+ case 0x8f:
+ case 0x82:
+ case 0x83:
+ case 0xd3:
+ case 0xd9:
+ case 0xcb:
+ lane_to_slot[6] = 2;
+ lane_to_slot[7] = 2;
+ break;
+ case 0xda:
+ lane_to_slot[4] = 3;
+ lane_to_slot[5] = 3;
+ lane_to_slot[6] = 3;
+ lane_to_slot[7] = 3;
+ break;
+ default:
+ break;
+ }
+}
+
+int board_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_FMAN_ENET)
+ int i, idx, lane, slot, interface;
+ struct memac_mdio_info dtsec_mdio_info;
+ struct memac_mdio_info tgec_mdio_info;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 rcwsr13 = in_be32(&gur->rcwsr[13]);
+ u32 srds_s1;
+
+ srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+ srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ initialize_lane_to_slot();
+
+ /* Initialize the mdio_mux array so we can recognize empty elements */
+ for (i = 0; i < NUM_FM_PORTS; i++)
+ mdio_mux[i] = EMI_NONE;
+
+ dtsec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
+
+ dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+ /* Register the 1G MDIO bus */
+ fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+ tgec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
+ tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+ /* Register the 10G MDIO bus */
+ fm_memac_mdio_init(bis, &tgec_mdio_info);
+
+ /* Register the muxing front-ends to the MDIO buses */
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1);
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2);
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1);
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2);
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3);
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4);
+ T2080qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5);
+ T2080qds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2);
+
+ /* Set the two on-board RGMII PHY address */
+ fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY1_ADDR);
+ if ((rcwsr13 & FSL_CORENET_RCWSR13_EC2) ==
+ FSL_CORENET_RCWSR13_EC2_DTSEC4_RGMII)
+ fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY2_ADDR);
+ else
+ fm_info_set_phy_address(FM1_DTSEC10, RGMII_PHY2_ADDR);
+
+ switch (srds_s1) {
+ case 0x1c:
+ case 0x95:
+ case 0xa2:
+ case 0x94:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC9, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
+ /* SGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT4_PHY_ADDR);
+ break;
+ case 0x51:
+ case 0x5f:
+ case 0x65:
+ /* XAUI/HiGig in Slot3 */
+ fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
+ /* SGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT4_PHY_ADDR);
+ break;
+ case 0x66:
+ /*
+ * XFI does not need a PHY to work, but to avoid U-boot use
+ * default PHY address which is zero to a MAC when it found
+ * a MAC has no PHY address, we give a PHY address to XFI
+ * MAC, and should not use a real XAUI PHY address, since
+ * MDIO can access it successfully, and then MDIO thinks
+ * the XAUI card is used for the XFI MAC, which will cause
+ * error.
+ */
+ fm_info_set_phy_address(FM1_10GEC1, 4);
+ fm_info_set_phy_address(FM1_10GEC2, 5);
+ fm_info_set_phy_address(FM1_10GEC3, 6);
+ fm_info_set_phy_address(FM1_10GEC4, 7);
+ break;
+ case 0x6b:
+ fm_info_set_phy_address(FM1_10GEC1, 4);
+ fm_info_set_phy_address(FM1_10GEC2, 5);
+ fm_info_set_phy_address(FM1_10GEC3, 6);
+ fm_info_set_phy_address(FM1_10GEC4, 7);
+ /* SGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+ break;
+ case 0x6c:
+ case 0x6d:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT2_PHY_ADDR);
+ break;
+ case 0x71:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
+ /* SGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+ break;
+ case 0xa6:
+ case 0x8e:
+ case 0x8f:
+ case 0x82:
+ case 0x83:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC9, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
+ /* SGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+ break;
+ case 0xa4:
+ case 0x96:
+ case 0x8a:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC9, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
+ break;
+ case 0xd9:
+ case 0xd3:
+ case 0xcb:
+ /* SGMII in Slot3 */
+ fm_info_set_phy_address(FM1_DTSEC10, SGMII_CARD_PORT2_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT4_PHY_ADDR);
+ /* SGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT3_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR);
+ break;
+ default:
+ puts("Invalid SerDes1 protocol for T2080QDS\n");
+ break;
+ }
+
+ for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+ idx = i - FM1_DTSEC1;
+ interface = fm_info_get_enet_if(i);
+ switch (interface) {
+ case PHY_INTERFACE_MODE_SGMII:
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ SGMII_FM1_DTSEC1 + idx);
+ if (lane < 0)
+ break;
+ slot = lane_to_slot[lane];
+ debug("FM1@DTSEC%u expects SGMII in slot %u\n",
+ idx + 1, slot);
+ if (QIXIS_READ(present2) & (1 << (slot - 1)))
+ fm_disable_port(i);
+
+ switch (slot) {
+ case 1:
+ mdio_mux[i] = EMI1_SLOT1;
+ fm_info_set_mdio(i, mii_dev_for_muxval(
+ mdio_mux[i]));
+ break;
+ case 2:
+ mdio_mux[i] = EMI1_SLOT2;
+ fm_info_set_mdio(i, mii_dev_for_muxval(
+ mdio_mux[i]));
+ break;
+ };
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ if (i == FM1_DTSEC3)
+ mdio_mux[i] = EMI1_RGMII1;
+ else if (i == FM1_DTSEC4 || FM1_DTSEC10)
+ mdio_mux[i] = EMI1_RGMII2;
+ fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
+ break;
+ default:
+ break;
+ }
+ }
+
+ for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
+ idx = i - FM1_10GEC1;
+ switch (fm_info_get_enet_if(i)) {
+ case PHY_INTERFACE_MODE_XGMII:
+ if (srds_s1 == 0x51) {
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ XAUI_FM1_MAC9 + idx);
+ } else if ((srds_s1 == 0x5f) || (srds_s1 == 0x65)) {
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ HIGIG_FM1_MAC9 + idx);
+ } else {
+ if (i == FM1_10GEC1 || i == FM1_10GEC2)
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ XFI_FM1_MAC9 + idx);
+ else
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ XFI_FM1_MAC1 + idx);
+ }
+
+ if (lane < 0)
+ break;
+ mdio_mux[i] = EMI2;
+ fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
+
+ if ((srds_s1 == 0x66) || (srds_s1 == 0x6b) ||
+ (srds_s1 == 0x6c) || (srds_s1 == 0x6d) ||
+ (srds_s1 == 0x71)) {
+ /* As XFI is in cage intead of a slot, so
+ * ensure doesn't disable the corresponding port
+ */
+ break;
+ }
+
+ slot = lane_to_slot[lane];
+ if (QIXIS_READ(present2) & (1 << (slot - 1)))
+ fm_disable_port(i);
+ break;
+ default:
+ break;
+ }
+ }
+
+ cpu_eth_init(bis);
+#endif /* CONFIG_FMAN_ENET */
+
+ return pci_eth_init(bis);
+}
--- /dev/null
+/*
+ * Copyright 2008-2012 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef QIXIS_BASE_PHYS
+ SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ /* Limit DCSR to 32M to access NPC Trace Buffer */
+ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
--- /dev/null
+/*
+ * Copyright 2007-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+ FT_FSL_PCI_SETUP;
+}
--- /dev/null
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Refer doc/README.pblimage for more details about how-to configure
+# and create PBL boot image
+#
+
+#PBI commands
+#Initialize CPC1
+09010000 00200400
+09138000 00000000
+091380c0 00000100
+#512KB SRAM
+09010100 00000000
+09010104 fff80009
+09010f00 08000000
+#enable CPC1
+09010000 80000000
+#Configure LAW for CPC1
+09000d00 00000000
+09000d04 fff80000
+09000d08 81000012
+#Initialize eSPI controller, default configuration is slow for eSPI to
+#load data, this configuration comes from u-boot eSPI driver.
+09110000 80000403
+09110020 2d170008
+09110024 00100008
+09110028 00100008
+0911002c 00100008
+#Errata for slowing down the MDC clock to make it <= 2.5 MHZ
+094fc030 00008148
+094fd030 00008148
+#Configure alternate space
+09000010 00000000
+09000014 ff000000
+09000018 81000000
+#Flush PBL data
+09138000 00000000
+091380c0 00000000
--- /dev/null
+#PBL preamble and RCW header
+aa55aa55 010e0100
+#SerDes Protocol: 0x66_0x16
+#Core/DDR: 1533Mhz/2133MT/s
+12100017 15000000 00000000 00000000
+66160002 00008400 e8104000 c1000000
+00000000 00000000 00000000 000307fc
+00000000 00000000 00000000 00000004
--- /dev/null
+/*
+ * Copyright 2009-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+
+#include "../common/qixis.h"
+#include "../common/vsc3316_3308.h"
+#include "t2080qds.h"
+#include "t2080qds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ char buf[64];
+ u8 sw;
+ struct cpu_type *cpu = gd->arch.cpu;
+ static const char *freq[4] = {
+ "100.00MHZ(from 8T49N222A)", "125.00MHz",
+ "156.25MHZ", "100.00MHz"
+ };
+
+ printf("Board: %sQDS, ", cpu->name);
+ sw = QIXIS_READ(arch);
+ printf("Sys ID: 0x%02x, Board Arch: V%d, ", QIXIS_READ(id), sw >> 4);
+ printf("Board Version: %c, boot from ", (sw & 0xf) + 'A' - 1);
+
+ sw = QIXIS_READ(brdcfg[0]);
+ sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+ if (sw < 0x8)
+ printf("vBank%d\n", sw);
+ else if (sw == 0x8)
+ puts("Promjet\n");
+ else if (sw == 0x9)
+ puts("NAND\n");
+ else
+ printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
+
+ printf("FPGA: v%d (%s), build %d", (int)QIXIS_READ(scver),
+ qixis_read_tag(buf), (int)qixis_read_minor());
+ /* the timestamp string contains "\n" at the end */
+ printf(" on %s", qixis_read_time(buf));
+
+ puts("SERDES Reference Clocks:\n");
+ sw = QIXIS_READ(brdcfg[2]);
+ printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[sw >> 6],
+ freq[(sw >> 4) & 0x3]);
+ printf("SD2_CLK1=%s, SD2_CLK2=%s\n", freq[(sw & 0xf) >> 2],
+ freq[sw & 0x3]);
+
+ return 0;
+}
+
+int select_i2c_ch_pca9547(u8 ch)
+{
+ int ret;
+
+ ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+ if (ret) {
+ puts("PCA: failed to select proper channel\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+int brd_mux_lane_to_slot(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_prtcl_s1, srds_prtcl_s2;
+
+ srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+ srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+ srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
+ srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
+
+ switch (srds_prtcl_s1) {
+ case 0:
+ /* SerDes1 is not enabled */
+ break;
+ case 0x1c:
+ case 0x95:
+ case 0xa2:
+ case 0x94:
+ /* SD1(A:D) => SLOT3 SGMII
+ * SD1(G:H) => SLOT1 SGMII
+ */
+ QIXIS_WRITE(brdcfg[12], 0x58);
+ break;
+ case 0x51:
+ /* SD1(A:D) => SLOT3 XAUI
+ * SD1(E) => SLOT1 PCIe4
+ * SD1(F:H) => SLOT2 SGMII
+ */
+ QIXIS_WRITE(brdcfg[12], 0x15);
+ break;
+ case 0x66:
+ case 0x67:
+ /* SD1(A:D) => XFI cage
+ * SD1(E:H) => SLOT1 PCIe4
+ */
+ QIXIS_WRITE(brdcfg[12], 0xfe);
+ break;
+ case 0x6b:
+ /* SD1(A:D) => XFI cage
+ * SD1(E) => SLOT1 PCIe4
+ * SD1(F:H) => SLOT2 SGMII
+ */
+ QIXIS_WRITE(brdcfg[12], 0xf1);
+ break;
+ case 0x6c:
+ case 0x6d:
+ /* SD1(A:B) => XFI cage
+ * SD1(C:D) => SLOT3 SGMII
+ * SD1(E:H) => SLOT1 PCIe4
+ */
+ QIXIS_WRITE(brdcfg[12], 0xda);
+ break;
+ default:
+ printf("WARNING: unsupported for SerDes1 Protocol %d\n",
+ srds_prtcl_s1);
+ return -1;
+ }
+
+ switch (srds_prtcl_s2) {
+ case 0:
+ /* SerDes2 is not enabled */
+ break;
+ case 0x01:
+ case 0x02:
+ /* SD2(A:H) => SLOT4 PCIe1 */
+ QIXIS_WRITE(brdcfg[13], 0x20);
+ break;
+ case 0x15:
+ case 0x16:
+ /*
+ * SD2(A:D) => SLOT4 PCIe1
+ * SD2(E:F) => SLOT5 PCIe2
+ * SD2(G:H) => SATA1,SATA2
+ */
+ QIXIS_WRITE(brdcfg[13], 0xb0);
+ break;
+ case 0x18:
+ /*
+ * SD2(A:D) => SLOT4 PCIe1
+ * SD2(E:F) => SLOT5 Aurora
+ * SD2(G:H) => SATA1,SATA2
+ */
+ QIXIS_WRITE(brdcfg[13], 0x70);
+ break;
+ case 0x1f:
+ /*
+ * SD2(A:D) => SLOT4 PCIe1
+ * SD2(E:H) => SLOT5 PCIe2
+ */
+ QIXIS_WRITE(brdcfg[13], 0xa0);
+ break;
+ case 0x29:
+ case 0x2d:
+ case 0x2e:
+ /*
+ * SD2(A:D) => SLOT4 SRIO2
+ * SD2(E:H) => SLOT5 SRIO1
+ */
+ QIXIS_WRITE(brdcfg[13], 0x50);
+ break;
+ default:
+ printf("WARNING: unsupported for SerDes2 Protocol %d\n",
+ srds_prtcl_s2);
+ return -1;
+ }
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash + PROMJET region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* invalidate existing TLB entry for flash + promjet */
+ disable_tlb(flash_esel);
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+ set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ setup_portals();
+#endif
+
+ /* Disable remote I2C connection to qixis fpga */
+ QIXIS_WRITE(brdcfg[5], QIXIS_READ(brdcfg[5]) & ~BRDCFG5_IRE);
+
+ brd_mux_lane_to_slot();
+ select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+
+ return 0;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT
+ /* use accurate clock measurement */
+ int freq = QIXIS_READ(clk_freq[0]) << 8 | QIXIS_READ(clk_freq[1]);
+ int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]);
+ u32 val;
+
+ val = freq * base;
+ if (val) {
+ debug("SYS Clock measurement is: %d\n", val);
+ return val;
+ } else {
+ printf("Warning: SYS clock measurement is invalid, ");
+ printf("using value from brdcfg1.\n");
+ }
+#endif
+
+ switch (sysclk_conf & 0x0F) {
+ case QIXIS_SYSCLK_83:
+ return 83333333;
+ case QIXIS_SYSCLK_100:
+ return 100000000;
+ case QIXIS_SYSCLK_125:
+ return 125000000;
+ case QIXIS_SYSCLK_133:
+ return 133333333;
+ case QIXIS_SYSCLK_150:
+ return 150000000;
+ case QIXIS_SYSCLK_160:
+ return 160000000;
+ case QIXIS_SYSCLK_166:
+ return 166666666;
+ }
+ return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+#ifdef CONFIG_FSL_QIXIS_CLOCK_MEASUREMENT
+ /* use accurate clock measurement */
+ int freq = QIXIS_READ(clk_freq[2]) << 8 | QIXIS_READ(clk_freq[3]);
+ int base = QIXIS_READ(clk_base[0]) << 8 | QIXIS_READ(clk_base[1]);
+ u32 val;
+
+ val = freq * base;
+ if (val) {
+ debug("DDR Clock measurement is: %d\n", val);
+ return val;
+ } else {
+ printf("Warning: DDR clock measurement is invalid, ");
+ printf("using value from brdcfg1.\n");
+ }
+#endif
+
+ switch ((ddrclk_conf & 0x30) >> 4) {
+ case QIXIS_DDRCLK_100:
+ return 100000000;
+ case QIXIS_DDRCLK_125:
+ return 125000000;
+ case QIXIS_DDRCLK_133:
+ return 133333333;
+ }
+ return 66666666;
+}
+
+int misc_init_r(void)
+{
+ return 0;
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+ fdt_fixup_dr_usb(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+ fdt_fixup_board_enet(blob);
+#endif
+}
--- /dev/null
+/*
+ * Copyright 2011-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CORENET_DS_H__
+#define __CORENET_DS_H__
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+
+#endif
--- /dev/null
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __T2080QDS_QIXIS_H__
+#define __T2080QDS_QIXIS_H__
+
+/* Definitions of QIXIS Registers for T2080QDS */
+
+#define QIXIS_SRDS1CLK_122 0x5a
+#define QIXIS_SRDS1CLK_125 0x5e
+
+
+/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */
+#define BRDCFG4_EMISEL_MASK 0xE0
+#define BRDCFG4_EMISEL_SHIFT 5
+
+/* SYSCLK */
+#define QIXIS_SYSCLK_66 0x0
+#define QIXIS_SYSCLK_83 0x1
+#define QIXIS_SYSCLK_100 0x2
+#define QIXIS_SYSCLK_125 0x3
+#define QIXIS_SYSCLK_133 0x4
+#define QIXIS_SYSCLK_150 0x5
+#define QIXIS_SYSCLK_160 0x6
+#define QIXIS_SYSCLK_166 0x7
+
+/* DDRCLK */
+#define QIXIS_DDRCLK_66 0x0
+#define QIXIS_DDRCLK_100 0x1
+#define QIXIS_DDRCLK_125 0x2
+#define QIXIS_DDRCLK_133 0x3
+
+#define BRDCFG5_IRE 0x20 /* i2c Remote i2c1 enable */
+
+#define BRDCFG12_SD3EN_MASK 0x20
+#define BRDCFG12_SD3MX_MASK 0x08
+#define BRDCFG12_SD3MX_SLOT5 0x08
+#define BRDCFG12_SD3MX_SLOT6 0x00
+#define BRDCFG12_SD4EN_MASK 0x04
+#define BRDCFG12_SD4MX_MASK 0x03
+#define BRDCFG12_SD4MX_SLOT7 0x02
+#define BRDCFG12_SD4MX_SLOT8 0x01
+#define BRDCFG12_SD4MX_AURO_SATA 0x00
+#endif
--- /dev/null
+/*
+ * Copyright 2008-2013 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+ /*
+ * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
+ * SRAM is at 0xfff00000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_1M, 1),
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+ /*
+ * SRIO_PCIE_BOOT-SLAVE. When slave boot, the address of the
+ * space is at 0xfff00000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR,
+ CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_1M, 1),
+#else
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_16M, 1),
+
+ /* *I*G* - Flash, localbus */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCIe 1, 0x80000000 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_512M, 1),
+
+ /* *I*G* - PCIe 2, 0xa0000000 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_VIRT, CONFIG_SYS_PCIE2_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCIe 3, 0xb0000000 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+
+
+ /* *I*G* - PCIe 4, 0xc0000000 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE4_MEM_VIRT, CONFIG_SYS_PCIE4_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 7, BOOKE_PAGESZ_256K, 1),
+
+ /* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 9, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 10, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 11, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 12, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 13, BOOKE_PAGESZ_32M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+ /*
+ * *I*G - NAND
+ * entry 14 and 15 has been used hard coded, they will be disabled
+ * in cpu_init_f, so we use entry 16 for nand.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 16, BOOKE_PAGESZ_64K, 1),
+#endif
+#ifdef QIXIS_BASE_PHYS
+ SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 17, BOOKE_PAGESZ_4K, 1),
+#endif
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+ /*
+ * SRIO_PCIE_BOOT-SLAVE. 1M space from 0xffe00000 for
+ * fetching ucode and ENV from master
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR,
+ CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
+ 0, 18, BOOKE_PAGESZ_1M, 1),
+#endif
+
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
#include <asm/fsl_law.h>
#include "ddr.h"
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/fsl_portals.h>
#include <asm/fsl_liodn.h>
#include <asm/cache.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <asm/io.h>
#include <libfdt.h>
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm,
unsigned int ctrl_num)
#include <i2c.h>
#include <hwconfig.h>
#include <asm/mmu.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
obj-y += sbc8548.o
obj-y += law.o
obj-y += tlb.o
-obj-$(CONFIG_FSL_DDR2) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
*/
phys_size_t fixed_sdram(void)
{
- volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);
out_be32(&ddr->cs0_bnds, 0x0000007f);
out_be32(&ddr->cs1_bnds, 0x008000ff);
#include <asm/processor.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <spd_sdram.h>
#include <netdev.h>
obj-y += sbc8641d.o
obj-y += law.o
-obj-$(CONFIG_FSL_DDR2) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/immap_86xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_serdes.h>
#include <libfdt.h>
#include <fdt_support.h>
{
#if !defined(CONFIG_SYS_RAMBOOT)
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile ccsr_ddr_t *ddr = &immap->im_ddr1;
+ volatile struct ccsr_ddr *ddr = &immap->im_ddr1;
ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
ddr->cs1_bnds = CONFIG_SYS_DDR_CS1_BNDS;
ddr->sdram_cfg_2 = CONFIG_SYS_DDR_CFG_2;
ddr->sdram_mode = CONFIG_SYS_DDR_MODE_1;
ddr->sdram_mode_2 = CONFIG_SYS_DDR_MODE_2;
- ddr->sdram_mode_cntl = CONFIG_SYS_DDR_MODE_CTL;
+ ddr->sdram_md_cntl = CONFIG_SYS_DDR_MODE_CTL;
ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
ddr->sdram_data_init = CONFIG_SYS_DDR_DATA_INIT;
ddr->sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL;
ddr->sdram_cfg_2 = CONFIG_SYS_DDR2_CFG_2;
ddr->sdram_mode = CONFIG_SYS_DDR2_MODE_1;
ddr->sdram_mode_2 = CONFIG_SYS_DDR2_MODE_2;
- ddr->sdram_mode_cntl = CONFIG_SYS_DDR2_MODE_CTL;
+ ddr->sdram_md_cntl = CONFIG_SYS_DDR2_MODE_CTL;
ddr->sdram_interval = CONFIG_SYS_DDR2_INTERVAL;
ddr->sdram_data_init = CONFIG_SYS_DDR2_DATA_INIT;
ddr->sdram_clk_cntl = CONFIG_SYS_DDR2_CLK_CTRL;
obj-y += tlb.o
obj-y += nand.o
obj-y += sdram.o
-obj-$(CONFIG_FSL_DDR2) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr.o
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <common.h>
#include <asm/processor.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/processor.h>
#include <asm/mmu.h>
#include <spd_sdram.h>
*/
phys_size_t fixed_sdram(void)
{
- volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);
/*
* Disable memory controller.
obj-y += law.o
obj-y += tlb.o
obj-y += flash.o
-obj-$(CONFIG_FSL_DDR1) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR1) += ddr.o
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <ioports.h>
#include <asm/io.h>
#include <spd_sdram.h>
obj-y += stxssa.o
obj-y += law.o
obj-y += tlb.o
-obj-$(CONFIG_FSL_DDR1) += ddr.o
+obj-$(CONFIG_SYS_FSL_DDR1) += ddr.o
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_pci.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <ioports.h>
#include <asm/io.h>
#include <spd_sdram.h>
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address)
{
#include <common.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/mmu.h>
#include <asm/io.h>
#include <fdt_support.h>
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
{
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void get_spd(ddr2_spd_eeprom_t *spd, u8 i2c_address)
{
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
void get_spd(ddr3_spd_eeprom_t *spd, u8 i2c_address)
{
Active powerpc mpc85xx - freescale t4qds T4240QDS_SDCARD T4240QDS:PPC_T4240,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000 -
Active powerpc mpc85xx - freescale t4qds T4240QDS_SPIFLASH T4240QDS:PPC_T4240,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 -
Active powerpc mpc85xx - freescale t4qds T4240QDS_SRIO_PCIE_BOOT T4240QDS:PPC_T4240,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 -
-Active powerpc mpc85xx - freescale t1040qds T1040QDS T1040QDS:PPC_T1040 Naveen Burmi <NaveenBurmi@freescale.com>
+Active powerpc mpc85xx - freescale t1040qds T1040QDS T1040QDS:PPC_T1040 Poonam Aggrwal <poonam.aggrwal@freescale.com>
Active powerpc mpc85xx - freescale t104xrdb T1040RDB T1040RDB:PPC_T1040 Poonam Aggrwal <poonam.aggrwal@freescale.com>
Active powerpc mpc85xx - freescale t104xrdb T1042RDB_PI T1042RDB_PI:PPC_T1042 Poonam Aggrwal <poonam.aggrwal@freescale.com>
+Active powerpc mpc85xx - freescale t2080qds T2080QDS T2080QDS:PPC_T2080
+Active powerpc mpc85xx - freescale t2080qds T2080QDS_SDCARD T2080QDS:PPC_T2080,RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000
+Active powerpc mpc85xx - freescale t2080qds T2080QDS_SPIFLASH T2080QDS:PPC_T2080,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
+Active powerpc mpc85xx - freescale t2080qds T2080QDS_NAND T2080QDS:PPC_T2080,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000
+Active powerpc mpc85xx - freescale t2080qds T2080QDS_SRIO_PCIE_BOOT T2080QDS:PPC_T2080,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000
Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD controlcenterd:36BIT,SDCARD Dirk Eibach <eibach@gdsys.de>
Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD_DEVELOP controlcenterd:36BIT,SDCARD,DEVELOP Dirk Eibach <eibach@gdsys.de>
Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER controlcenterd:TRAILBLAZER,SPIFLASH Dirk Eibach <eibach@gdsys.de>
--- /dev/null
+#
+# Copyright 2008-2011 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License
+# Version 2 as published by the Free Software Foundation.
+#
+
+obj-$(CONFIG_SYS_FSL_DDR1) += main.o util.o ctrl_regs.o options.o \
+ lc_common_dimm_params.o
+
+obj-$(CONFIG_SYS_FSL_DDR2) += main.o util.o ctrl_regs.o options.o \
+ lc_common_dimm_params.o
+
+obj-$(CONFIG_SYS_FSL_DDR3) += main.o util.o ctrl_regs.o options.o \
+ lc_common_dimm_params.o
+ifdef CONFIG_DDR_SPD
+SPD := y
+endif
+ifdef CONFIG_SPD_EEPROM
+SPD := y
+endif
+ifdef SPD
+obj-$(CONFIG_SYS_FSL_DDR1) += ddr1_dimm_params.o
+obj-$(CONFIG_SYS_FSL_DDR2) += ddr2_dimm_params.o
+obj-$(CONFIG_SYS_FSL_DDR3) += ddr3_dimm_params.o
+endif
+
+obj-$(CONFIG_FSL_DDR_INTERACTIVE) += interactive.o
+obj-$(CONFIG_SYS_FSL_DDRC_GEN1) += mpc85xx_ddr_gen1.o
+obj-$(CONFIG_SYS_FSL_DDRC_GEN2) += mpc85xx_ddr_gen2.o
+obj-$(CONFIG_SYS_FSL_DDRC_GEN3) += mpc85xx_ddr_gen3.o
+obj-$(CONFIG_SYS_FSL_DDR_86XX) += mpc86xx_ddr.o
+obj-$(CONFIG_SYS_FSL_DDRC_ARM_GEN3) += arm_ddr_gen3.o
--- /dev/null
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Derived from mpc85xx_ddr_gen3.c, removed all workarounds
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <fsl_ddr_sdram.h>
+#include <asm/processor.h>
+#include <fsl_immap.h>
+
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
+#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
+#endif
+
+
+/*
+ * regs has the to-be-set values for DDR controller registers
+ * ctrl_num is the DDR controller number
+ * step: 0 goes through the initialization in one pass
+ * 1 sets registers and returns before enabling controller
+ * 2 resumes from step 1 and continues to initialize
+ * Dividing the initialization to two steps to deassert DDR reset signal
+ * to comply with JEDEC specs for RDIMMs.
+ */
+void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
+ unsigned int ctrl_num, int step)
+{
+ unsigned int i, bus_width;
+ struct ccsr_ddr __iomem *ddr;
+ u32 temp_sdram_cfg;
+ u32 total_gb_size_per_controller;
+ int timeout;
+
+ switch (ctrl_num) {
+ case 0:
+ ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR;
+ break;
+#if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
+ case 1:
+ ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR;
+ break;
+#endif
+#if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
+ case 2:
+ ddr = (void *)CONFIG_SYS_FSL_DDR3_ADDR;
+ break;
+#endif
+#if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
+ case 3:
+ ddr = (void *)CONFIG_SYS_FSL_DDR4_ADDR;
+ break;
+#endif
+ default:
+ printf("%s unexpected ctrl_num = %u\n", __func__, ctrl_num);
+ return;
+ }
+
+ if (step == 2)
+ goto step2;
+
+ if (regs->ddr_eor)
+ out_be32(&ddr->eor, regs->ddr_eor);
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ if (i == 0) {
+ out_be32(&ddr->cs0_bnds, regs->cs[i].bnds);
+ out_be32(&ddr->cs0_config, regs->cs[i].config);
+ out_be32(&ddr->cs0_config_2, regs->cs[i].config_2);
+
+ } else if (i == 1) {
+ out_be32(&ddr->cs1_bnds, regs->cs[i].bnds);
+ out_be32(&ddr->cs1_config, regs->cs[i].config);
+ out_be32(&ddr->cs1_config_2, regs->cs[i].config_2);
+
+ } else if (i == 2) {
+ out_be32(&ddr->cs2_bnds, regs->cs[i].bnds);
+ out_be32(&ddr->cs2_config, regs->cs[i].config);
+ out_be32(&ddr->cs2_config_2, regs->cs[i].config_2);
+
+ } else if (i == 3) {
+ out_be32(&ddr->cs3_bnds, regs->cs[i].bnds);
+ out_be32(&ddr->cs3_config, regs->cs[i].config);
+ out_be32(&ddr->cs3_config_2, regs->cs[i].config_2);
+ }
+ }
+
+ out_be32(&ddr->timing_cfg_3, regs->timing_cfg_3);
+ out_be32(&ddr->timing_cfg_0, regs->timing_cfg_0);
+ out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1);
+ out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2);
+ out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
+ out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode);
+ out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2);
+ out_be32(&ddr->sdram_mode_3, regs->ddr_sdram_mode_3);
+ out_be32(&ddr->sdram_mode_4, regs->ddr_sdram_mode_4);
+ out_be32(&ddr->sdram_mode_5, regs->ddr_sdram_mode_5);
+ out_be32(&ddr->sdram_mode_6, regs->ddr_sdram_mode_6);
+ out_be32(&ddr->sdram_mode_7, regs->ddr_sdram_mode_7);
+ out_be32(&ddr->sdram_mode_8, regs->ddr_sdram_mode_8);
+ out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl);
+ out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval);
+ out_be32(&ddr->sdram_data_init, regs->ddr_data_init);
+ out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
+ out_be32(&ddr->init_addr, regs->ddr_init_addr);
+ out_be32(&ddr->init_ext_addr, regs->ddr_init_ext_addr);
+
+ out_be32(&ddr->timing_cfg_4, regs->timing_cfg_4);
+ out_be32(&ddr->timing_cfg_5, regs->timing_cfg_5);
+ out_be32(&ddr->ddr_zq_cntl, regs->ddr_zq_cntl);
+ out_be32(&ddr->ddr_wrlvl_cntl, regs->ddr_wrlvl_cntl);
+#ifndef CONFIG_SYS_FSL_DDR_EMU
+ /*
+ * Skip these two registers if running on emulator
+ * because emulator doesn't have skew between bytes.
+ */
+
+ if (regs->ddr_wrlvl_cntl_2)
+ out_be32(&ddr->ddr_wrlvl_cntl_2, regs->ddr_wrlvl_cntl_2);
+ if (regs->ddr_wrlvl_cntl_3)
+ out_be32(&ddr->ddr_wrlvl_cntl_3, regs->ddr_wrlvl_cntl_3);
+#endif
+
+ out_be32(&ddr->ddr_sr_cntr, regs->ddr_sr_cntr);
+ out_be32(&ddr->ddr_sdram_rcw_1, regs->ddr_sdram_rcw_1);
+ out_be32(&ddr->ddr_sdram_rcw_2, regs->ddr_sdram_rcw_2);
+ out_be32(&ddr->ddr_cdr1, regs->ddr_cdr1);
+ out_be32(&ddr->ddr_cdr2, regs->ddr_cdr2);
+ out_be32(&ddr->err_disable, regs->err_disable);
+ out_be32(&ddr->err_int_en, regs->err_int_en);
+ for (i = 0; i < 32; i++) {
+ if (regs->debug[i]) {
+ debug("Write to debug_%d as %08x\n", i + 1,
+ regs->debug[i]);
+ out_be32(&ddr->debug[i], regs->debug[i]);
+ }
+ }
+
+ /*
+ * For RDIMMs, JEDEC spec requires clocks to be stable before reset is
+ * deasserted. Clocks start when any chip select is enabled and clock
+ * control register is set. Because all DDR components are connected to
+ * one reset signal, this needs to be done in two steps. Step 1 is to
+ * get the clocks started. Step 2 resumes after reset signal is
+ * deasserted.
+ */
+ if (step == 1) {
+ udelay(200);
+ return;
+ }
+
+step2:
+ /* Set, but do not enable the memory */
+ temp_sdram_cfg = regs->ddr_sdram_cfg;
+ temp_sdram_cfg &= ~(SDRAM_CFG_MEM_EN);
+ out_be32(&ddr->sdram_cfg, temp_sdram_cfg);
+
+ /*
+ * 500 painful micro-seconds must elapse between
+ * the DDR clock setup and the DDR config enable.
+ * DDR2 need 200 us, and DDR3 need 500 us from spec,
+ * we choose the max, that is 500 us for all of case.
+ */
+ udelay(500);
+ asm volatile("dsb sy;isb");
+
+ /* Let the controller go */
+ temp_sdram_cfg = in_be32(&ddr->sdram_cfg) & ~SDRAM_CFG_BI;
+ out_be32(&ddr->sdram_cfg, temp_sdram_cfg | SDRAM_CFG_MEM_EN);
+ asm volatile("dsb sy;isb");
+
+ total_gb_size_per_controller = 0;
+ for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+ if (!(regs->cs[i].config & 0x80000000))
+ continue;
+ total_gb_size_per_controller += 1 << (
+ ((regs->cs[i].config >> 14) & 0x3) + 2 +
+ ((regs->cs[i].config >> 8) & 0x7) + 12 +
+ ((regs->cs[i].config >> 0) & 0x7) + 8 +
+ 3 - ((regs->ddr_sdram_cfg >> 19) & 0x3) -
+ 26); /* minus 26 (count of 64M) */
+ }
+ if (regs->cs[0].config & 0x20000000) {
+ /* 2-way interleaving */
+ total_gb_size_per_controller <<= 1;
+ }
+ /*
+ * total memory / bus width = transactions needed
+ * transactions needed / data rate = seconds
+ * to add plenty of buffer, double the time
+ * For example, 2GB on 666MT/s 64-bit bus takes about 402ms
+ * Let's wait for 800ms
+ */
+ bus_width = 3 - ((ddr->sdram_cfg & SDRAM_CFG_DBW_MASK)
+ >> SDRAM_CFG_DBW_SHIFT);
+ timeout = ((total_gb_size_per_controller << (6 - bus_width)) * 100 /
+ (get_ddr_freq(0) >> 20)) << 1;
+ total_gb_size_per_controller >>= 4; /* shift down to gb size */
+ debug("total %d GB\n", total_gb_size_per_controller);
+ debug("Need to wait up to %d * 10ms\n", timeout);
+
+ /* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done. */
+ while ((in_be32(&ddr->sdram_cfg_2) & SDRAM_CFG2_D_INIT) &&
+ (timeout >= 0)) {
+ udelay(10000); /* throttle polling rate */
+ timeout--;
+ }
+
+ if (timeout <= 0)
+ printf("Waiting for D_INIT timeout. Memory may not work.\n");
+}
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
+#include <fsl_immap.h>
+#include <asm/io.h>
-#define _DDR_ADDR CONFIG_SYS_MPC8xxx_DDR_ADDR
+#define _DDR_ADDR CONFIG_SYS_FSL_DDR_ADDR
static u32 fsl_ddr_get_version(void)
{
- ccsr_ddr_t *ddr;
+ struct ccsr_ddr __iomem *ddr;
u32 ver_major_minor_errata;
ddr = (void *)_DDR_ADDR;
{
int rtt;
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
rtt = 0;
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
rtt = 3;
#else
rtt = 0;
/* -3E = 667 CL5, -25 = CL6 800, -25E = CL5 800 */
-#if !defined(CONFIG_FSL_DDR1)
+#if !defined(CONFIG_SYS_FSL_DDR1)
static inline int avoid_odt_overlap(const dimm_params_t *dimm_params)
{
#if CONFIG_DIMM_SLOTS_PER_CTLR == 1
/* Mode register set cycle time (tMRD). */
unsigned char tmrd_mclk;
-#ifdef CONFIG_FSL_DDR3
+#ifdef CONFIG_SYS_FSL_DDR3
/*
* (tXARD and tXARDS). Empirical?
* The DDR3 spec has not tXARD,
pre_pd_exit_mclk = act_pd_exit_mclk;
taxpd_mclk = 1;
}
-#else /* CONFIG_FSL_DDR2 */
+#else /* CONFIG_SYS_FSL_DDR2 */
/*
* (tXARD and tXARDS). Empirical?
* tXARD = 2 for DDR2
| ((twrt_mclk & 0x3) << 28) /* WRT */
| ((trrt_mclk & 0x3) << 26) /* RRT */
| ((twwt_mclk & 0x3) << 24) /* WWT */
- | ((act_pd_exit_mclk & 0x7) << 20) /* ACT_PD_EXIT */
+ | ((act_pd_exit_mclk & 0xf) << 20) /* ACT_PD_EXIT */
| ((pre_pd_exit_mclk & 0xF) << 16) /* PRE_PD_EXIT */
| ((taxpd_mclk & 0xf) << 8) /* ODT_PD_EXIT */
- | ((tmrd_mclk & 0xf) << 0) /* MRS_CYC */
+ | ((tmrd_mclk & 0x1f) << 0) /* MRS_CYC */
);
debug("FSLDDR: timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0);
}
-#endif /* defined(CONFIG_FSL_DDR2) */
+#endif /* defined(CONFIG_SYS_FSL_DDR2) */
/* DDR SDRAM Timing Configuration 3 (TIMING_CFG_3) */
static void set_timing_cfg_3(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
const common_timing_params_t *common_dimm,
- unsigned int cas_latency)
+ unsigned int cas_latency,
+ unsigned int additive_latency)
{
/* Extended precharge to activate interval (tRP) */
unsigned int ext_pretoact = 0;
unsigned int ext_refrec;
/* Extended MCAS latency from READ cmd */
unsigned int ext_caslat = 0;
+ /* Extended additive latency */
+ unsigned int ext_add_lat = 0;
/* Extended last data to precharge interval (tWR) */
unsigned int ext_wrrec = 0;
/* Control Adjust */
ext_acttopre = picos_to_mclk(common_dimm->tras_ps) >> 4;
ext_acttorw = picos_to_mclk(common_dimm->trcd_ps) >> 4;
ext_caslat = (2 * cas_latency - 1) >> 4;
+ ext_add_lat = additive_latency >> 4;
ext_refrec = (picos_to_mclk(common_dimm->trfc_ps) - 8) >> 4;
/* ext_wrrec only deals with 16 clock and above, or 14 with OTF */
ext_wrrec = (picos_to_mclk(common_dimm->twr_ps) +
| ((ext_acttorw & 0x1) << 22)
| ((ext_refrec & 0x1F) << 16)
| ((ext_caslat & 0x3) << 12)
+ | ((ext_add_lat & 0x1) << 10)
| ((ext_wrrec & 0x1) << 8)
| ((cntl_adj & 0x7) << 0)
);
* 4.5 1000
* 5.0 5 1001
*/
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
caslat_ctrl = (cas_latency + 1) & 0x07;
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
caslat_ctrl = 2 * cas_latency - 1;
#else
/*
/*
* JEDEC has min requirement for tRRD
*/
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
if (acttoact_mclk < 4)
acttoact_mclk = 4;
#endif
/*
* JEDEC has some min requirements for tWTR
*/
-#if defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR2)
if (wrtord_mclk < 2)
wrtord_mclk = 2;
-#elif defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR3)
if (wrtord_mclk < 4)
wrtord_mclk = 4;
#endif
add_lat_mclk = additive_latency;
cpo = popts->cpo_override;
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
/*
* This is a lie. It should really be 1, but if it is
* set to 1, bits overlap into the old controller's
* the HW will magically treat it as 1 for DDR 1. Oh Yea.
*/
wr_lat = 0;
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
wr_lat = cas_latency - 1;
#else
wr_lat = compute_cas_write_latency();
/*
* JEDEC has some min requirements for tRTP
*/
-#if defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR2)
if (rd_to_pre < 2)
rd_to_pre = 2;
-#elif defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR3)
if (rd_to_pre < 4)
rd_to_pre = 4;
#endif
- if (additive_latency)
- rd_to_pre += additive_latency;
if (popts->otf_burst_chop_en)
rd_to_pre += 2; /* according to UM */
* * ({EXT_REFREC || REFREC} + 8 + 2)]}
* << DDR_SDRAM_INTERVAL[REFINT]
*/
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
obc_cfg = popts->otf_burst_chop_en;
#else
obc_cfg = 0;
d_init = 0;
#endif
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
md_en = popts->mirrored_dimm;
#endif
qd_en = popts->quad_rank_present ? 1 : 0;
unsigned short esdmode2 = 0; /* Extended SDRAM mode 2 */
unsigned short esdmode3 = 0; /* Extended SDRAM mode 3 */
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
int i;
unsigned int rtt_wr = 0; /* Rtt_WR - dynamic ODT off */
unsigned int srt = 0; /* self-refresh temerature, normal range */
);
debug("FSLDDR: ddr_sdram_mode_2 = 0x%08x\n", ddr->ddr_sdram_mode_2);
-#ifdef CONFIG_FSL_DDR3
+#ifdef CONFIG_SYS_FSL_DDR3
if (unq_mrs_en) { /* unique mode registers are supported */
for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (popts->rtt_override)
debug("FSLDDR: ddr_sdram_interval = 0x%08x\n", ddr->ddr_sdram_interval);
}
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
/* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */
static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr,
const memctl_options_t *popts,
}
}
-#else /* !CONFIG_FSL_DDR3 */
+#else /* !CONFIG_SYS_FSL_DDR3 */
/* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */
static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr,
unsigned int bt;
unsigned int bl; /* BL: Burst Length */
-#if defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR2)
const unsigned int mclk_ps = get_memory_clk_period_ps();
#endif
dqs_en = !popts->dqs_config;
*/
pd = 0;
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
wr = 0; /* Historical */
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
wr = (common_dimm->twr_ps + mclk_ps - 1) / mclk_ps - 1;
#endif
dll_res = 0;
mode = 0;
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
if (1 <= cas_latency && cas_latency <= 4) {
unsigned char mode_caslat_table[4] = {
0x5, /* 1.5 clocks */
} else {
printf("Warning: unknown cas_latency %d\n", cas_latency);
}
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
caslat = cas_latency;
#endif
bt = 0;
unsigned int wwt = 0; /* Write-to-write turnaround for same CS */
unsigned int dll_lock = 0; /* DDR SDRAM DLL Lock Time */
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
if (popts->burst_length == DDR_BL8) {
/* We set BL/2 for fixed BL8 */
rrt = 0; /* BL/2 clocks */
unsigned int wodt_on = 0; /* Write to ODT on */
unsigned int wodt_off = 0; /* Write to ODT off */
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
/* rodt_on = timing_cfg_1[caslat] - timing_cfg_2[wrlat] + 1 */
rodt_on = cas_latency - ((ddr->timing_cfg_2 & 0x00780000) >> 19) + 1;
rodt_off = 4; /* 4 clocks */
if (cs_en) {
ddr->cs[i].bnds = (0
- | ((sa & 0xFFF) << 16)/* starting address MSB */
- | ((ea & 0xFFF) << 0) /* ending address MSB */
+ | ((sa & 0xffff) << 16) /* starting address */
+ | ((ea & 0xffff) << 0) /* ending address */
);
} else {
/* setting bnds to 0xffffffff for inactive CS */
set_ddr_eor(ddr, popts);
-#if !defined(CONFIG_FSL_DDR1)
+#if !defined(CONFIG_SYS_FSL_DDR1)
set_timing_cfg_0(ddr, popts, dimm_params);
#endif
- set_timing_cfg_3(ddr, popts, common_dimm, cas_latency);
+ set_timing_cfg_3(ddr, popts, common_dimm, cas_latency,
+ additive_latency);
set_timing_cfg_1(ddr, popts, common_dimm, cas_latency);
set_timing_cfg_2(ddr, popts, common_dimm,
cas_latency, additive_latency);
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
/*
* Calculate the Density of each Physical Rank.
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
/*
* Calculate the Density of each Physical Rank.
* Returned size is in bytes.
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
/*
* Calculate the Density of each Physical Rank.
#include <common.h>
#include <linux/ctype.h>
#include <asm/types.h>
+#include <asm/io.h>
-#include <asm/fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr.h>
/* Option parameter Structures */
struct options_string {
CTRL_OPTIONS_CS(3, odt_rd_cfg),
CTRL_OPTIONS_CS(3, odt_wr_cfg),
#endif
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
CTRL_OPTIONS_CS(0, odt_rtt_norm),
CTRL_OPTIONS_CS(0, odt_rtt_wr),
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1)
CTRL_OPTIONS_CS(3, odt_rd_cfg),
CTRL_OPTIONS_CS(3, odt_wr_cfg),
#endif
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
CTRL_OPTIONS_CS(0, odt_rtt_norm),
CTRL_OPTIONS_CS(0, odt_rtt_wr),
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 1)
print_option_table(options, n_opts, popts);
}
-#ifdef CONFIG_FSL_DDR1
+#ifdef CONFIG_SYS_FSL_DDR1
void ddr1_spd_dump(const ddr1_spd_eeprom_t *spd)
{
unsigned int i;
}
#endif
-#ifdef CONFIG_FSL_DDR2
+#ifdef CONFIG_SYS_FSL_DDR2
void ddr2_spd_dump(const ddr2_spd_eeprom_t *spd)
{
unsigned int i;
}
#endif
-#ifdef CONFIG_FSL_DDR3
+#ifdef CONFIG_SYS_FSL_DDR3
void ddr3_spd_dump(const ddr3_spd_eeprom_t *spd)
{
unsigned int i;
static inline void generic_spd_dump(const generic_spd_eeprom_t *spd)
{
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
ddr1_spd_dump(spd);
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
ddr2_spd_dump(spd);
-#elif defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR3)
ddr3_spd_dump(spd);
#endif
}
*/
#include <common.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
static unsigned int
compute_cas_latency_ddr3(const dimm_params_t *dimm_params,
common_timing_params_t *outpdimm,
unsigned int temp1, temp2;
unsigned int additive_latency = 0;
-#if !defined(CONFIG_FSL_DDR3)
+#if !defined(CONFIG_SYS_FSL_DDR3)
const unsigned int mclk_ps = get_memory_clk_period_ps();
unsigned int lowest_good_caslat;
unsigned int not_ok;
if (temp1 != 0)
printf("ERROR: Mix different RDIMM detected!\n");
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
if (compute_cas_latency_ddr3(dimm_params, outpdimm, number_of_dimms))
return 1;
#else
}
outpdimm->highest_common_derated_caslat = temp1;
debug("highest common dereated CAS latency = %u\n", temp1);
-#endif /* #if defined(CONFIG_FSL_DDR3) */
+#endif /* #if defined(CONFIG_SYS_FSL_DDR3) */
/* Determine if all DIMMs ECC capable. */
temp1 = 1;
}
outpdimm->all_dimms_ecc_capable = temp1;
-#ifndef CONFIG_FSL_DDR3
+#ifndef CONFIG_SYS_FSL_DDR3
/* FIXME: move to somewhere else to validate. */
if (mclk_ps > tckmax_max_ps) {
printf("Warning: some of the installed DIMMs "
additive_latency = 0;
-#if defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR2)
if (lowest_good_caslat < 4) {
additive_latency = (picos_to_mclk(trcd_ps) > lowest_good_caslat)
? picos_to_mclk(trcd_ps) - lowest_good_caslat : 0;
}
}
-#elif defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR3)
/*
* The system will not use the global auto-precharge mode.
* However, it uses the page mode, so we set AL=0
#include <common.h>
#include <i2c.h>
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_law.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr.h>
-#include "ddr.h"
+#ifdef CONFIG_PPC
+#include <asm/fsl_law.h>
void fsl_ddr_set_lawbar(
const common_timing_params_t *memctl_common_params,
unsigned int memctl_interleaved,
unsigned int ctrl_num);
-void fsl_ddr_set_intl3r(const unsigned int granule_size);
+#endif
+void fsl_ddr_set_intl3r(const unsigned int granule_size);
#if defined(SPD_EEPROM_ADDRESS) || \
defined(SPD_EEPROM_ADDRESS1) || defined(SPD_EEPROM_ADDRESS2) || \
defined(SPD_EEPROM_ADDRESS3) || defined(SPD_EEPROM_ADDRESS4)
debug("dbw_cap_adj[%d]=%d\n", i, dbw_cap_adj[i]);
}
- current_mem_base = 0ull;
+ current_mem_base = CONFIG_SYS_DDR_SDRAM_BASE;
total_mem = 0;
if (pinfo->memctl_opts[0].memctl_interleaving) {
rank_density = pinfo->dimm_params[0][0].rank_density >>
}
}
- total_mem = 1 + (((unsigned long long)max_end << 24ULL)
- | 0xFFFFFFULL);
+ total_mem = 1 + (((unsigned long long)max_end << 24ULL) |
+ 0xFFFFFFULL) - CONFIG_SYS_DDR_SDRAM_BASE;
}
return total_mem;
phys_size_t fsl_ddr_sdram(void)
{
unsigned int i;
+#ifdef CONFIG_PPC
unsigned int law_memctl = LAW_TRGT_IF_DDR_1;
+#endif
unsigned long long total_memory;
fsl_ddr_info_t info;
int deassert_reset;
}
}
+#ifdef CONFIG_PPC
/* program LAWs */
for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) {
if (info.memctl_opts[i].memctl_interleaving) {
law_memctl, i);
}
}
+#endif
debug("total_memory by %s = %llu\n", __func__, total_memory);
#include <common.h>
#include <asm/io.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
unsigned int ctrl_num, int step)
{
unsigned int i;
- volatile ccsr_ddr_t *ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
if (ctrl_num != 0) {
printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
void
ddr_enable_ecc(unsigned int dram_size)
{
- volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);
dma_meminit(CONFIG_MEM_INIT_VALUE, dram_size);
#include <common.h>
#include <asm/io.h>
#include <asm/processor.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
unsigned int ctrl_num, int step)
{
unsigned int i;
- ccsr_ddr_t *ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
#if defined(CONFIG_SYS_FSL_ERRATUM_NMG_DDR120) && defined(CONFIG_MPC85xx)
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
#include <common.h>
#include <asm/io.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/processor.h>
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
unsigned int ctrl_num, int step)
{
unsigned int i, bus_width;
- volatile ccsr_ddr_t *ddr;
+ struct ccsr_ddr __iomem *ddr;
u32 temp_sdram_cfg;
u32 total_gb_size_per_controller;
int timeout;
switch (ctrl_num) {
case 0:
- ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR;
break;
-#if defined(CONFIG_SYS_MPC8xxx_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
+#if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
case 1:
- ddr = (void *)CONFIG_SYS_MPC8xxx_DDR2_ADDR;
+ ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR;
break;
#endif
-#if defined(CONFIG_SYS_MPC8xxx_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
+#if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
case 2:
- ddr = (void *)CONFIG_SYS_MPC8xxx_DDR3_ADDR;
+ ddr = (void *)CONFIG_SYS_FSL_DDR3_ADDR;
break;
#endif
-#if defined(CONFIG_SYS_MPC8xxx_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
+#if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
case 3:
- ddr = (void *)CONFIG_SYS_MPC8xxx_DDR4_ADDR;
+ ddr = (void *)CONFIG_SYS_FSL_DDR4_ADDR;
break;
#endif
default:
#include <common.h>
#include <asm/io.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
unsigned int ctrl_num, int step)
{
unsigned int i;
- volatile ccsr_ddr_t *ddr;
+ struct ccsr_ddr __iomem *ddr;
switch (ctrl_num) {
case 0:
- ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR;
break;
case 1:
- ddr = (void *)CONFIG_SYS_MPC8xxx_DDR2_ADDR;
+ ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR;
break;
default:
printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode);
out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2);
- out_be32(&ddr->sdram_mode_cntl, regs->ddr_sdram_md_cntl);
+ out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl);
out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval);
out_be32(&ddr->sdram_data_init, regs->ddr_data_init);
out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
#include <common.h>
#include <hwconfig.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
/*
* Use our own stack based buffer before relocation to allow accessing longer
unsigned int odt_rtt_wr;
};
-#ifdef CONFIG_FSL_DDR3
+#ifdef CONFIG_SYS_FSL_DDR3
static const struct dynamic_odt single_Q[4] = {
{ /* cs0 */
FSL_DDR_ODT_NEVER,
DDR3_RTT_OFF
}
};
-#else /* CONFIG_FSL_DDR3 */
+#else /* CONFIG_SYS_FSL_DDR3 */
static const struct dynamic_odt single_Q[4] = {
{0, 0, 0, 0},
{0, 0, 0, 0},
unsigned int i;
char buffer[HWCONFIG_BUFFER_SIZE];
char *buf = NULL;
-#if defined(CONFIG_FSL_DDR3) || defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR2)
const struct dynamic_odt *pdodt = odt_unknown;
#endif
ulong ddr_freq;
if (getenv_f("hwconfig", buffer, sizeof(buffer)) > 0)
buf = buffer;
-#if defined(CONFIG_FSL_DDR3) || defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR2)
/* Chip select options. */
if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
switch (pdimm[0].n_ranks) {
/* Pick chip-select local options. */
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
-#if defined(CONFIG_FSL_DDR3) || defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR2)
popts->cs_local_opts[i].odt_rd_cfg = pdodt[i].odt_rd_cfg;
popts->cs_local_opts[i].odt_wr_cfg = pdodt[i].odt_wr_cfg;
popts->cs_local_opts[i].odt_rtt_norm = pdodt[i].odt_rtt_norm;
* 0 for DDR1
* 1 for DDR2
*/
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
popts->dqs_config = 0;
-#elif defined(CONFIG_FSL_DDR2) || defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR2) || defined(CONFIG_SYS_FSL_DDR3)
popts->dqs_config = 1;
#endif
* presuming all dimms are similar
* 0 = 64-bit, 1 = 32-bit, 2 = 16-bit
*/
-#if defined(CONFIG_FSL_DDR1) || defined(CONFIG_FSL_DDR2)
+#if defined(CONFIG_SYS_FSL_DDR1) || defined(CONFIG_SYS_FSL_DDR2)
if (pdimm[0].n_ranks != 0) {
if ((pdimm[0].data_width >= 64) && \
(pdimm[0].data_width <= 72))
popts->x4_en = (pdimm[0].device_width == 4) ? 1 : 0;
/* Choose burst length. */
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
#if defined(CONFIG_E500MC)
popts->otf_burst_chop_en = 0; /* on-the-fly burst chop disable */
popts->burst_length = DDR_BL8; /* Fixed 8-beat burst len */
#endif
/* Choose ddr controller address mirror mode */
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
popts->mirrored_dimm = pdimm[0].mirrored_dimm;
#endif
* FIXME: varies depending upon number of column addresses or data
* FIXME: width, was considering looking at pdimm->primary_sdram_width
*/
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
popts->tfaw_window_four_activates_ps = mclk_to_picos(1);
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
/*
* x4/x8; some datasheets have 35000
* x16 wide columns only? Use 50000?
*/
popts->tfaw_window_four_activates_ps = 37500;
-#elif defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR3)
popts->tfaw_window_four_activates_ps = pdimm[0].tfaw_ps;
#endif
popts->zq_en = 0;
popts->wrlvl_en = 0;
-#if defined(CONFIG_FSL_DDR3)
+#if defined(CONFIG_SYS_FSL_DDR3)
/*
* due to ddr3 dimm is fly-by topology
* we suggest to enable write leveling to
*/
#include <common.h>
+#ifdef CONFIG_PPC
#include <asm/fsl_law.h>
+#endif
#include <div64.h>
-#include "ddr.h"
+#include <fsl_ddr.h>
+#include <fsl_immap.h>
+#include <asm/io.h>
/* To avoid 64-bit full-divides, we factor this here */
#define ULL_2E12 2000000000000ULL
return get_memory_clk_period_ps() * mclk;
}
+#ifdef CONFIG_PPC
void
__fsl_ddr_set_lawbar(const common_timing_params_t *memctl_common_params,
unsigned int law_memctl,
fsl_ddr_set_lawbar(const common_timing_params_t *memctl_common_params,
unsigned int memctl_interleaved,
unsigned int ctrl_num);
+#endif
void fsl_ddr_set_intl3r(const unsigned int granule_size)
{
void board_add_ram_info(int use_default)
{
- ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);
#if defined(CONFIG_E6500) && (CONFIG_NUM_DDR_CONTROLLERS == 3)
u32 *mcintl3r = (void *) (CONFIG_SYS_IMMR + 0x18004);
#if CONFIG_NUM_DDR_CONTROLLERS >= 2
if (!(sdram_cfg & SDRAM_CFG_MEM_EN)) {
- ddr = (void __iomem *)CONFIG_SYS_MPC8xxx_DDR2_ADDR;
+ ddr = (void __iomem *)CONFIG_SYS_FSL_DDR2_ADDR;
sdram_cfg = in_be32(&ddr->sdram_cfg);
}
#endif
#if CONFIG_NUM_DDR_CONTROLLERS >= 3
if (!(sdram_cfg & SDRAM_CFG_MEM_EN)) {
- ddr = (void __iomem *)CONFIG_SYS_MPC8xxx_DDR3_ADDR;
+ ddr = (void __iomem *)CONFIG_SYS_FSL_DDR3_ADDR;
sdram_cfg = in_be32(&ddr->sdram_cfg);
}
#endif
obj-$(CONFIG_PDSP188x) += pdsp188x.o
obj-$(CONFIG_STATUS_LED) += status_led.o
obj-$(CONFIG_TWL4030_LED) += twl4030_led.o
+obj-$(CONFIG_FSL_IFC) += fsl_ifc.o
*/
#include <common.h>
-#include <asm/fsl_ifc.h>
+#include <fsl_ifc.h>
void print_ifc_regs(void)
{
#include <asm/io.h>
#include <asm/errno.h>
-#include <asm/fsl_ifc.h>
+#include <fsl_ifc.h>
#define FSL_IFC_V1_1_0 0x01010000
#define MAX_BANKS 4
#include <common.h>
#include <asm/io.h>
-#include <asm/fsl_ifc.h>
+#include <fsl_ifc.h>
#include <linux/mtd/nand.h>
static inline int is_blank(uchar *addr, int page_size)
obj-$(CONFIG_PPC_T1042) += t1040.o
obj-$(CONFIG_PPC_T1020) += t1040.o
obj-$(CONFIG_PPC_T1022) += t1040.o
+obj-$(CONFIG_PPC_T2080) += t2080.o
+obj-$(CONFIG_PPC_T2081) += t2080.o
obj-$(CONFIG_PPC_T4240) += t4240.o
obj-$(CONFIG_PPC_T4160) += t4240.o
obj-$(CONFIG_PPC_B4420) += b4860.o
num = fm_eth->num;
#ifdef CONFIG_SYS_FMAN_V3
- if (fm_eth->type == FM_ETH_10G_E)
- num += 8;
+ if (fm_eth->type == FM_ETH_10G_E) {
+ /* 10GEC1/10GEC2 use mEMAC9/mEMAC10
+ * 10GEC3/10GEC4 use mEMAC1/mEMAC2
+ * so it needs to change the num.
+ */
+ if (fm_eth->num >= 2)
+ num -= 2;
+ else
+ num += 8;
+ }
base = ®->memac[num].fm_memac;
phyregs = ®->memac[num].fm_memac_mdio;
#else
#define RX_PORT_1G_BASE 0x08
#define MAX_NUM_RX_PORT_1G CONFIG_SYS_NUM_FM1_DTSEC
#define RX_PORT_10G_BASE 0x10
+#define RX_PORT_10G_BASE2 0x08
#define TX_PORT_1G_BASE 0x28
#define MAX_NUM_TX_PORT_1G CONFIG_SYS_NUM_FM1_DTSEC
#define TX_PORT_10G_BASE 0x30
+#define TX_PORT_10G_BASE2 0x28
#define MIIM_TIMEOUT 0xFFFF
struct fm_muram {
#if (CONFIG_SYS_NUM_FM1_10GEC >= 2)
FM_TGEC_INFO_INITIALIZER(1, 2),
#endif
+#if (CONFIG_SYS_NUM_FM1_10GEC >= 3)
+ FM_TGEC_INFO_INITIALIZER2(1, 3),
+#endif
+#if (CONFIG_SYS_NUM_FM1_10GEC >= 4)
+ FM_TGEC_INFO_INITIALIZER2(1, 4),
+#endif
#if (CONFIG_SYS_NUM_FM2_10GEC >= 1)
FM_TGEC_INFO_INITIALIZER(2, 1),
#endif
* FM1_10GEC1 is enabled and FM1_DTSEC9 is disabled, ensure that the
* dual-role MAC is not disabled, ditto for other dual-role MACs.
*/
- if (((info->port == FM1_DTSEC9) && (PORT_IS_ENABLED(FM1_10GEC1))) ||
- ((info->port == FM1_DTSEC10) && (PORT_IS_ENABLED(FM1_10GEC2))) ||
- ((info->port == FM1_10GEC1) && (PORT_IS_ENABLED(FM1_DTSEC9))) ||
- ((info->port == FM1_10GEC2) && (PORT_IS_ENABLED(FM1_DTSEC10)))
+ if (((info->port == FM1_DTSEC9) && (PORT_IS_ENABLED(FM1_10GEC1))) ||
+ ((info->port == FM1_DTSEC10) && (PORT_IS_ENABLED(FM1_10GEC2))) ||
+ ((info->port == FM1_DTSEC1) && (PORT_IS_ENABLED(FM1_10GEC3))) ||
+ ((info->port == FM1_DTSEC2) && (PORT_IS_ENABLED(FM1_10GEC4))) ||
+ ((info->port == FM1_10GEC1) && (PORT_IS_ENABLED(FM1_DTSEC9))) ||
+ ((info->port == FM1_10GEC2) && (PORT_IS_ENABLED(FM1_DTSEC10))) ||
+ ((info->port == FM1_10GEC3) && (PORT_IS_ENABLED(FM1_DTSEC1))) ||
+ ((info->port == FM1_10GEC4) && (PORT_IS_ENABLED(FM1_DTSEC2)))
#if (CONFIG_SYS_NUM_FMAN == 2)
||
((info->port == FM2_DTSEC9) && (PORT_IS_ENABLED(FM2_10GEC1))) ||
--- /dev/null
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * Shengzhou Liu <Shengzhou.Liu@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <phy.h>
+#include <fm_eth.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_serdes.h>
+
+u32 port_to_devdisr[] = {
+ [FM1_DTSEC1] = FSL_CORENET_DEVDISR2_DTSEC1_1,
+ [FM1_DTSEC2] = FSL_CORENET_DEVDISR2_DTSEC1_2,
+ [FM1_DTSEC3] = FSL_CORENET_DEVDISR2_DTSEC1_3,
+ [FM1_DTSEC4] = FSL_CORENET_DEVDISR2_DTSEC1_4,
+ [FM1_DTSEC5] = FSL_CORENET_DEVDISR2_DTSEC1_5,
+ [FM1_DTSEC6] = FSL_CORENET_DEVDISR2_DTSEC1_6,
+ [FM1_DTSEC9] = FSL_CORENET_DEVDISR2_DTSEC1_9,
+ [FM1_DTSEC10] = FSL_CORENET_DEVDISR2_DTSEC1_10,
+ [FM1_10GEC1] = FSL_CORENET_DEVDISR2_10GEC1_1,
+ [FM1_10GEC2] = FSL_CORENET_DEVDISR2_10GEC1_2,
+ [FM1_10GEC3] = FSL_CORENET_DEVDISR2_10GEC1_3,
+ [FM1_10GEC4] = FSL_CORENET_DEVDISR2_10GEC1_4,
+};
+
+static int is_device_disabled(enum fm_port port)
+{
+ ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 devdisr2 = in_be32(&gur->devdisr2);
+
+ return port_to_devdisr[port] & devdisr2;
+}
+
+void fman_disable_port(enum fm_port port)
+{
+ ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+ setbits_be32(&gur->devdisr2, port_to_devdisr[port]);
+}
+
+phy_interface_t fman_port_enet_if(enum fm_port port)
+{
+ ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 rcwsr13 = in_be32(&gur->rcwsr[13]);
+
+ if (is_device_disabled(port))
+ return PHY_INTERFACE_MODE_NONE;
+
+ if ((port == FM1_10GEC1 || port == FM1_10GEC2 ||
+ port == FM1_10GEC3 || port == FM1_10GEC4) &&
+ ((is_serdes_configured(XAUI_FM1_MAC9)) ||
+ (is_serdes_configured(XFI_FM1_MAC1)) ||
+ (is_serdes_configured(XFI_FM1_MAC2)) ||
+ (is_serdes_configured(XFI_FM1_MAC9)) ||
+ (is_serdes_configured(XFI_FM1_MAC10))))
+ return PHY_INTERFACE_MODE_XGMII;
+
+ if ((port == FM1_DTSEC3) && ((rcwsr13 & FSL_CORENET_RCWSR13_EC1) ==
+ FSL_CORENET_RCWSR13_EC1_DTSEC3_RGMII))
+ return PHY_INTERFACE_MODE_RGMII;
+
+ if ((port == FM1_DTSEC4) && ((rcwsr13 & FSL_CORENET_RCWSR13_EC2) ==
+ FSL_CORENET_RCWSR13_EC2_DTSEC4_RGMII))
+ return PHY_INTERFACE_MODE_RGMII;
+
+ if ((port == FM1_DTSEC10) && ((rcwsr13 & FSL_CORENET_RCWSR13_EC2) ==
+ FSL_CORENET_RCWSR13_EC2_DTSEC10_RGMII))
+ return PHY_INTERFACE_MODE_RGMII;
+
+ switch (port) {
+ case FM1_DTSEC1:
+ case FM1_DTSEC2:
+ case FM1_DTSEC3:
+ case FM1_DTSEC4:
+ case FM1_DTSEC5:
+ case FM1_DTSEC6:
+ case FM1_DTSEC9:
+ case FM1_DTSEC10:
+ if (is_serdes_configured(SGMII_FM1_DTSEC1 + port - FM1_DTSEC1))
+ return PHY_INTERFACE_MODE_SGMII;
+ break;
+ default:
+ return PHY_INTERFACE_MODE_NONE;
+ }
+
+ return PHY_INTERFACE_MODE_NONE;
+}
#define CONFIG_DDR_SPD
#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_SYS_MEMTEST_END 0x01ffffff
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#undef CONFIG_SYS_DDR_RAW_TIMING
#undef CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_SYS_MEMTEST_END 0x01ffffff
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS1 0x54 /* I2C access */
#define SPD_EEPROM_ADDRESS2 0x56 /* I2C access */
#define CONFIG_PANIC_HANG
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x50
/* -------------------------------------------------------------------- */
/* FreeScale DDR2/3 SDRAM Controller */
-#define CONFIG_FSL_DDR2 /* Our SDRAM slot is DDR2 */
+#define CONFIG_SYS_FSL_DDR2 /* Our SDRAM slot is DDR2 */
#define CONFIG_DDR_ECC /* Enable ECC by default */
#define CONFIG_DDR_SPD /* Detect DDR config from SPD EEPROM */
#define CONFIG_SPD_EEPROM /* ...why 2 config variables for this? */
#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
/*
- * define CONFIG_FSL_DDR2 to use unified DDR driver
+ * define CONFIG_SYS_FSL_DDR2 to use unified DDR driver
* undefine it to use old spd_sdram.c
*/
-#define CONFIG_FSL_DDR2
-#ifdef CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
+#ifdef CONFIG_SYS_FSL_DDR2
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS1 0x52
#define SPD_EEPROM_ADDRESS2 0x51
/* DDR Setup */
#define CONFIG_VERY_BIG_RAM
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#endif
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
/* DDR Setup */
#define CONFIG_VERY_BIG_RAM
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD for DDR */
#define CONFIG_DDR_SPD
/*
* DDR Setup
*/
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 1
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
#endif
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITION
+#define CONFIG_CMD_MTDPARTS
+#define MTDIDS_DEFAULT "nand0=ff800000.flash"
+#define MTDPARTS_DEFAULT \
+ "mtdparts=ff800000.flash:2m(uboot-env),1m(dtb),5m(kernel),56m(fs),-(usr)"
+
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| CSPR_PORT_SIZE_8 \
| CSPR_MSEL_NAND \
/* DDR Setup */
#define CONFIG_DDR_SPD
#define CONFIG_VERY_BIG_RAM
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#ifdef CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
#define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SDRAM_SIZE 512u /* DDR is 512M */
#define CONFIG_SYS_SPD_BUS_NUM 0
#endif
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
/* DDR Setup */
#define CONFIG_VERY_BIG_RAM
#ifdef CONFIG_DDR2
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#else
-#define CONFIG_FSL_DDR3 1
+#define CONFIG_SYS_FSL_DDR3 1
#endif
/* ECC will be enabled based on perf_mode environment variable */
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x52
#define CONFIG_MMC
#define CONFIG_PCIE3
+#define CONFIG_CMD_SATA
+#define CONFIG_SATA_SIL
+#define CONFIG_SYS_SATA_MAX_DEVICE 2
+#define CONFIG_LIBATA
+#define CONFIG_LBA48
+
#define CONFIG_SYS_SRIO
#define CONFIG_SRIO1 /* SRIO port 1 */
#define CONFIG_SRIO2 /* SRIO port 2 */
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_DDR_SPD
#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x51
#define CONFIG_DDR_SPD
#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x51
--- /dev/null
+/*
+ * Copyright 2011-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * T2080 QDS board configuration file
+ */
+
+#ifndef __T2080QDS_H
+#define __T2080QDS_H
+
+#define CONFIG_T2080QDS
+#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
+#define CONFIG_MMC
+#define CONFIG_SPI_FLASH
+#define CONFIG_USB_EHCI
+#define CONFIG_FSL_SATA_V2
+#define CONFIG_SYS_SRIO /* Enable Serial RapidIO Support */
+#define CONFIG_SRIO1 /* SRIO port 1 */
+#define CONFIG_SRIO2 /* SRIO port 2 */
+
+/* High Level Configuration Options */
+#define CONFIG_PHYS_64BIT
+#define CONFIG_BOOKE
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_E500MC /* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
+#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */
+#define CONFIG_MP /* support multiple processors */
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP 1
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC /* Enable IFC Support */
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t2080qds/t2080_pbi.cfg
+#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t2080qds/t2080_rcw.cfg
+#endif
+
+#define CONFIG_SRIO_PCIE_BOOT_MASTER
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+/* Set 1M boot space */
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+#endif
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#endif
+
+#ifdef CONFIG_SYS_NO_FLASH
+#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_ENV_IS_NOWHERE
+#endif
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (512 * 1105)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+#define CONFIG_ENV_IS_IN_REMOTE
+#define CONFIG_ENV_ADDR 0xffe20000
+#define CONFIG_ENV_SIZE 0x2000
+#elif defined(CONFIG_ENV_IS_NOWHERE)
+#define CONFIG_ENV_SIZE 0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
+#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
+
+/*
+ * Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
+
+#define CONFIG_SYS_DCSRBAR 0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_FSL_DDR3
+#define CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */
+#define SPD_EEPROM_ADDRESS1 0x51
+#define SPD_EEPROM_ADDRESS2 0x52
+#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
+#define CTRL_INTLV_PREFERED cacheline
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE 0xe0000000
+#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
+#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+ + 0x8000000) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EXT (0xf)
+#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
+
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
+ FTIM1_NOR_TRAD_NOR(0x1A) |\
+ FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0x0E) | \
+ FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3 0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \
+ + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+
+#define CONFIG_FSL_QIXIS /* use common QIXIS code */
+#define QIXIS_BASE 0xffdf0000
+#define QIXIS_LBMAP_SWITCH 6
+#define QIXIS_LBMAP_MASK 0x0f
+#define QIXIS_LBMAP_SHIFT 0
+#define QIXIS_LBMAP_DFLTBANK 0x00
+#define QIXIS_LBMAP_ALTBANK 0x04
+#define QIXIS_RST_CTL_RESET 0x83
+#define QIXIS_RST_FORCE_MEM 0x1
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
+#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE)
+
+#define CONFIG_SYS_CSPR3_EXT (0xf)
+#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+#define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024)
+#define CONFIG_SYS_CSOR3 0x0
+/* QIXIS Timing parameters for IFC CS3 */
+#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
+ FTIM1_GPCM_TRAD(0x3f))
+#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
+ FTIM2_GPCM_TCH(0x0) | \
+ FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS3_FTIM3 0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE 0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */\
+ | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW 11
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
+#endif
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+/*
+ * I2C
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
+#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
+#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
+#define CONFIG_SYS_FSL_I2C_SPEED 100000
+#define CONFIG_SYS_FSL_I2C2_SPEED 100000
+#define CONFIG_SYS_FSL_I2C3_SPEED 100000
+#define CONFIG_SYS_FSL_I2C4_SPEED 100000
+#define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */
+#define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */
+#define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */
+#define I2C_MUX_CH_DEFAULT 0x8
+
+
+/*
+ * RapidIO
+ */
+#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
+#define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
+#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
+#define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+/*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
+
+/* slave core release by master*/
+#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
+#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
+
+/*
+ * SRIO_PCIE_BOOT - SLAVE
+ */
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+#endif
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#ifdef CONFIG_SPI_FLASH
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE 0
+#endif
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controler 1 */
+#define CONFIG_PCIE2 /* PCIE controler 2 */
+#define CONFIG_PCIE3 /* PCIE controler 3 */
+#define CONFIG_PCIE4 /* PCIE controler 4 */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 4, Base address 203000 */
+#define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000
+#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull
+#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
+#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */
+#define CONFIG_NET_MULTI
+#define CONFIG_E1000
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 18
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS 18
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+#define CONFIG_SYS_PMAN
+#define CONFIG_SYS_DPAA_DCE
+#define CONFIG_SYS_DPAA_RMAN /* RMan */
+#define CONFIG_SYS_INTERLAKEN
+
+/* Default address of microcode for the Linux Fman driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 545KB (1089 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1130)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+/*
+ * Slave has no ucode locally, it can fetch this from remote. When implementing
+ * in two corenet boards, slave's ucode could be stored in master's memory
+ * space, the address can be mapped from slave TLB->slave LAW->
+ * slave SRIO or PCIE outbound window->master inbound window->
+ * master LAW->the ucode address in master's memory space.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHY_TERANETICS
+#define RGMII_PHY1_ADDR 0x1
+#define RGMII_PHY2_ADDR 0x2
+#define FM1_10GEC1_PHY_ADDR 0x3
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "FM1@DTSEC3"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * SATA
+ */
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+#define CONFIG_SYS_SATA_MAX_DEVICE 2
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
+#define CONFIG_SATA2
+#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
+#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+/*
+ * USB
+ */
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#define CONFIG_HAS_FSL_DR_USB
+#endif
+
+/*
+ * SDHC
+ */
+#ifdef CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_BDI
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#define __USB_PHY_TYPE utmi
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:" \
+ "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \
+ "bank_intlv=auto;" \
+ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+ "netdev=eth0\0" \
+ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot && " \
+ "protect off $ubootaddr +$filesize && " \
+ "erase $ubootaddr +$filesize && " \
+ "cp.b $loadaddr $ubootaddr $filesize && " \
+ "protect on $ubootaddr +$filesize && " \
+ "cmp.b $loadaddr $ubootaddr $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=t2080qds/ramdisk.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=t2080qds/t2080qds.dtb\0" \
+ "bdev=sda3\0" \
+ "c=ffe\0"
+
+/*
+ * For emulation this causes u-boot to jump to the start of the
+ * proof point app code automatically
+ */
+#define CONFIG_PROOF_POINTS \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "cpu 1 release 0x29000000 - - -;" \
+ "cpu 2 release 0x29000000 - - -;" \
+ "cpu 3 release 0x29000000 - - -;" \
+ "cpu 4 release 0x29000000 - - -;" \
+ "cpu 5 release 0x29000000 - - -;" \
+ "cpu 6 release 0x29000000 - - -;" \
+ "cpu 7 release 0x29000000 - - -;" \
+ "go 0x29000000"
+
+#define CONFIG_HVBOOT \
+ "setenv bootargs config-addr=0x60000000; " \
+ "bootm 0x01000000 - 0x00f00000"
+
+#define CONFIG_ALU \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "cpu 1 release 0x01000000 - - -;" \
+ "cpu 2 release 0x01000000 - - -;" \
+ "cpu 3 release 0x01000000 - - -;" \
+ "cpu 4 release 0x01000000 - - -;" \
+ "cpu 5 release 0x01000000 - - -;" \
+ "cpu 6 release 0x01000000 - - -;" \
+ "cpu 7 release 0x01000000 - - -;" \
+ "go 0x01000000"
+
+#define CONFIG_LINUX \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "setenv ramdiskaddr 0x02000000;" \
+ "setenv fdtaddr 0x00c00000;" \
+ "setenv loadaddr 0x1000000;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_HDBOOT \
+ "setenv bootargs root=/dev/$bdev rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#undef CONFIG_CMD_USB
+#endif
+
+#endif /* __T2080QDS_H */
#define CONFIG_SYS_SDRAM_SIZE 1024
#define CONFIG_VERY_BIG_RAM
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SPD_BUS_NUM 1
#define SPD_EEPROM_ADDRESS1 0x51
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#endif
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 1
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
/*
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
#define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
/*
/*
* DDR config
*/
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
/*
* DDR config
*/
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
/*
* DDR config
*/
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
/*
* DDR config
*/
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
FM1_DTSEC10,
FM1_10GEC1,
FM1_10GEC2,
+ FM1_10GEC3,
+ FM1_10GEC4,
FM2_DTSEC1,
FM2_DTSEC2,
FM2_DTSEC3,
.compat_offset = CONFIG_SYS_FSL_FM##idx##_OFFSET + \
offsetof(struct ccsr_fman, memac[n-1+8]),\
}
+
+#if (CONFIG_SYS_NUM_FM1_10GEC >= 3)
+#define FM_TGEC_INFO_INITIALIZER2(idx, n) \
+{ \
+ FM_ETH_INFO_INITIALIZER(idx, CONFIG_SYS_FM1_TGEC_MDIO_ADDR) \
+ .index = idx, \
+ .num = n - 1, \
+ .type = FM_ETH_10G_E, \
+ .port = FM##idx##_10GEC##n, \
+ .rx_port_id = RX_PORT_10G_BASE2 + n - 3, \
+ .tx_port_id = TX_PORT_10G_BASE2 + n - 3, \
+ .compat_offset = CONFIG_SYS_FSL_FM##idx##_OFFSET + \
+ offsetof(struct ccsr_fman, memac[n-1-2]),\
+}
+#endif
+
#else
#define FM_DTSEC_INFO_INITIALIZER(idx, n) \
{ \
#ifndef FSL_DDR_MAIN_H
#define FSL_DDR_MAIN_H
-#include <asm/fsl_ddr_sdram.h>
-#include <asm/fsl_ddr_dimm_params.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
-#include "common_timing_params.h"
+#include <common_timing_params.h>
#if defined(CONFIG_DDR_SPD) || defined(CONFIG_SPD_EEPROM)
/*
#define DDR2_RTT_150_OHM 2
#define DDR2_RTT_50_OHM 3
-#if defined(CONFIG_FSL_DDR1)
+#if defined(CONFIG_SYS_FSL_DDR1)
#define FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR (1)
typedef ddr1_spd_eeprom_t generic_spd_eeprom_t;
#ifndef CONFIG_FSL_SDRAM_TYPE
#define CONFIG_FSL_SDRAM_TYPE SDRAM_TYPE_DDR1
#endif
-#elif defined(CONFIG_FSL_DDR2)
+#elif defined(CONFIG_SYS_FSL_DDR2)
#define FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR (3)
typedef ddr2_spd_eeprom_t generic_spd_eeprom_t;
#ifndef CONFIG_FSL_SDRAM_TYPE
#define CONFIG_FSL_SDRAM_TYPE SDRAM_TYPE_DDR2
#endif
-#elif defined(CONFIG_FSL_DDR3)
+#elif defined(CONFIG_SYS_FSL_DDR3)
#define FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR (3) /* FIXME */
typedef ddr3_spd_eeprom_t generic_spd_eeprom_t;
#ifndef CONFIG_FSL_SDRAM_TYPE
#define CONFIG_FSL_SDRAM_TYPE SDRAM_TYPE_DDR3
#endif
-#endif /* #if defined(CONFIG_FSL_DDR1) */
+#endif /* #if defined(CONFIG_SYS_FSL_DDR1) */
#define FSL_DDR_ODT_NEVER 0x0
#define FSL_DDR_ODT_CS 0x1
* SPDX-License-Identifier: GPL-2.0+
*/
-#ifndef __ASM_PPC_FSL_IFC_H
-#define __ASM_PPC_FSL_IFC_H
+#ifndef __FSL_IFC_H
+#define __FSL_IFC_H
#ifdef CONFIG_FSL_IFC
#include <config.h>
#endif /* CONFIG_FSL_IFC */
#endif /* __ASSEMBLY__ */
-#endif /* __ASM_PPC_FSL_IFC_H */
+#endif /* __FSL_IFC_H */
--- /dev/null
+/*
+ * Common internal memory map for some Freescale SoCs
+ *
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __FSL_IMMAP_H
+#define __FSL_IMMAP_H
+/*
+ * DDR memory controller registers
+ * This structure works for mpc83xx (DDR2 and DDR3), mpc85xx, mpc86xx.
+ */
+struct ccsr_ddr {
+ u32 cs0_bnds; /* Chip Select 0 Memory Bounds */
+ u8 res_04[4];
+ u32 cs1_bnds; /* Chip Select 1 Memory Bounds */
+ u8 res_0c[4];
+ u32 cs2_bnds; /* Chip Select 2 Memory Bounds */
+ u8 res_14[4];
+ u32 cs3_bnds; /* Chip Select 3 Memory Bounds */
+ u8 res_1c[100];
+ u32 cs0_config; /* Chip Select Configuration */
+ u32 cs1_config; /* Chip Select Configuration */
+ u32 cs2_config; /* Chip Select Configuration */
+ u32 cs3_config; /* Chip Select Configuration */
+ u8 res_90[48];
+ u32 cs0_config_2; /* Chip Select Configuration 2 */
+ u32 cs1_config_2; /* Chip Select Configuration 2 */
+ u32 cs2_config_2; /* Chip Select Configuration 2 */
+ u32 cs3_config_2; /* Chip Select Configuration 2 */
+ u8 res_d0[48];
+ u32 timing_cfg_3; /* SDRAM Timing Configuration 3 */
+ u32 timing_cfg_0; /* SDRAM Timing Configuration 0 */
+ u32 timing_cfg_1; /* SDRAM Timing Configuration 1 */
+ u32 timing_cfg_2; /* SDRAM Timing Configuration 2 */
+ u32 sdram_cfg; /* SDRAM Control Configuration */
+ u32 sdram_cfg_2; /* SDRAM Control Configuration 2 */
+ u32 sdram_mode; /* SDRAM Mode Configuration */
+ u32 sdram_mode_2; /* SDRAM Mode Configuration 2 */
+ u32 sdram_md_cntl; /* SDRAM Mode Control */
+ u32 sdram_interval; /* SDRAM Interval Configuration */
+ u32 sdram_data_init; /* SDRAM Data initialization */
+ u8 res_12c[4];
+ u32 sdram_clk_cntl; /* SDRAM Clock Control */
+ u8 res_134[20];
+ u32 init_addr; /* training init addr */
+ u32 init_ext_addr; /* training init extended addr */
+ u8 res_150[16];
+ u32 timing_cfg_4; /* SDRAM Timing Configuration 4 */
+ u32 timing_cfg_5; /* SDRAM Timing Configuration 5 */
+ u8 reg_168[8];
+ u32 ddr_zq_cntl; /* ZQ calibration control*/
+ u32 ddr_wrlvl_cntl; /* write leveling control*/
+ u8 reg_178[4];
+ u32 ddr_sr_cntr; /* self refresh counter */
+ u32 ddr_sdram_rcw_1; /* Control Words 1 */
+ u32 ddr_sdram_rcw_2; /* Control Words 2 */
+ u8 reg_188[8];
+ u32 ddr_wrlvl_cntl_2; /* write leveling control 2 */
+ u32 ddr_wrlvl_cntl_3; /* write leveling control 3 */
+ u8 res_198[104];
+ u32 sdram_mode_3; /* SDRAM Mode Configuration 3 */
+ u32 sdram_mode_4; /* SDRAM Mode Configuration 4 */
+ u32 sdram_mode_5; /* SDRAM Mode Configuration 5 */
+ u32 sdram_mode_6; /* SDRAM Mode Configuration 6 */
+ u32 sdram_mode_7; /* SDRAM Mode Configuration 7 */
+ u32 sdram_mode_8; /* SDRAM Mode Configuration 8 */
+ u8 res_218[0x908];
+ u32 ddr_dsr1; /* Debug Status 1 */
+ u32 ddr_dsr2; /* Debug Status 2 */
+ u32 ddr_cdr1; /* Control Driver 1 */
+ u32 ddr_cdr2; /* Control Driver 2 */
+ u8 res_b30[200];
+ u32 ip_rev1; /* IP Block Revision 1 */
+ u32 ip_rev2; /* IP Block Revision 2 */
+ u32 eor; /* Enhanced Optimization Register */
+ u8 res_c04[252];
+ u32 mtcr; /* Memory Test Control Register */
+ u8 res_d04[28];
+ u32 mtp1; /* Memory Test Pattern 1 */
+ u32 mtp2; /* Memory Test Pattern 2 */
+ u32 mtp3; /* Memory Test Pattern 3 */
+ u32 mtp4; /* Memory Test Pattern 4 */
+ u32 mtp5; /* Memory Test Pattern 5 */
+ u32 mtp6; /* Memory Test Pattern 6 */
+ u32 mtp7; /* Memory Test Pattern 7 */
+ u32 mtp8; /* Memory Test Pattern 8 */
+ u32 mtp9; /* Memory Test Pattern 9 */
+ u32 mtp10; /* Memory Test Pattern 10 */
+ u8 res_d48[184];
+ u32 data_err_inject_hi; /* Data Path Err Injection Mask High */
+ u32 data_err_inject_lo; /* Data Path Err Injection Mask Low */
+ u32 ecc_err_inject; /* Data Path Err Injection Mask ECC */
+ u8 res_e0c[20];
+ u32 capture_data_hi; /* Data Path Read Capture High */
+ u32 capture_data_lo; /* Data Path Read Capture Low */
+ u32 capture_ecc; /* Data Path Read Capture ECC */
+ u8 res_e2c[20];
+ u32 err_detect; /* Error Detect */
+ u32 err_disable; /* Error Disable */
+ u32 err_int_en;
+ u32 capture_attributes; /* Error Attrs Capture */
+ u32 capture_address; /* Error Addr Capture */
+ u32 capture_ext_address; /* Error Extended Addr Capture */
+ u32 err_sbe; /* Single-Bit ECC Error Management */
+ u8 res_e5c[164];
+ u32 debug[32]; /* debug_1 to debug_32 */
+ u8 res_f80[128];
+};
+#endif /* __FSL_IMMAP_H */
u32 flags;
};
+struct fixed_link {
+ int phy_id;
+ int duplex;
+ int link_speed;
+ int pause;
+ int asym_pause;
+};
+
static inline int phy_read(struct phy_device *phydev, int devad, int regnum)
{
struct mii_dev *bus = phydev->bus;
#include <nand.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_law.h>
#define SYSCLK_66 66666666
#include <asm/io.h>
#include <nand.h>
#include <asm/fsl_law.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/global_data.h>
DECLARE_GLOBAL_DATA_PTR;
/* Fixed sdram init -- doesn't use serial presence detect. */
void sdram_init(void)
{
- ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
+ struct ccsr_ddr __iomem *ddr =
+ (struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1);
#include <nand.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
-#include <asm/fsl_ddr_sdram.h>
+#include <fsl_ddr_sdram.h>
#include <asm/fsl_law.h>
#define SYSCLK_MASK 0x00200000
LIBS-$(CONFIG_SPL_I2C_SUPPORT) += drivers/i2c/
LIBS-$(CONFIG_SPL_GPIO_SUPPORT) += drivers/gpio/
LIBS-$(CONFIG_SPL_MMC_SUPPORT) += drivers/mmc/
+LIBS-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += drivers/ddr/fsl/
LIBS-$(CONFIG_SPL_SERIAL_SUPPORT) += drivers/serial/
LIBS-$(CONFIG_SPL_SPI_FLASH_SUPPORT) += drivers/mtd/spi/
LIBS-$(CONFIG_SPL_SPI_SUPPORT) += drivers/spi/
projects / karo-tx-uboot.git / commitdiff