With driver model GPIOs must be requested before use. Make sure this is
done correctly.
(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)
Signed-off-by: Simon Glass <sjg@chromium.org>
* this same assumption.
*/
if ((peripheral == PERIPH_ID_SDMMC0) && (i == (start + 2))) {
* this same assumption.
*/
if ((peripheral == PERIPH_ID_SDMMC0) && (i == (start + 2))) {
+#ifndef CONFIG_SPL_BUILD
+ gpio_request(i, "sdmmc0_vdden");
+#endif
gpio_set_value(i, 1);
gpio_cfg_pin(i, S5P_GPIO_OUTPUT);
} else {
gpio_set_value(i, 1);
gpio_cfg_pin(i, S5P_GPIO_OUTPUT);
} else {
/* Configure gpios for usb 3503 hub:
* disconnect, toggle reset and connect
*/
/* Configure gpios for usb 3503 hub:
* disconnect, toggle reset and connect
*/
+ gpio_request(EXYNOS5_GPIO_D17, "usb_connect");
+ gpio_request(EXYNOS5_GPIO_X35, "usb_reset");
gpio_direction_output(EXYNOS5_GPIO_D17, 0);
gpio_direction_output(EXYNOS5_GPIO_X35, 0);
gpio_direction_output(EXYNOS5_GPIO_D17, 0);
gpio_direction_output(EXYNOS5_GPIO_X35, 0);
void keys_init(void)
{
/* Set direction to input */
void keys_init(void)
{
/* Set direction to input */
+ gpio_request(KEY_VOL_UP_GPIO, "volume-up");
+ gpio_request(KEY_VOL_DOWN_GPIO, "volume-down");
gpio_direction_input(KEY_VOL_UP_GPIO);
gpio_direction_input(KEY_VOL_DOWN_GPIO);
}
gpio_direction_input(KEY_VOL_UP_GPIO);
gpio_direction_input(KEY_VOL_DOWN_GPIO);
}
int i, ret, ret_sd = 0;
/* MASSMEMORY_EN: XMSMDATA7: GPJ2[7] output high */
int i, ret, ret_sd = 0;
/* MASSMEMORY_EN: XMSMDATA7: GPJ2[7] output high */
+ gpio_request(S5PC110_GPIO_J27, "massmemory_en");
gpio_direction_output(S5PC110_GPIO_J27, 1);
/*
gpio_direction_output(S5PC110_GPIO_J27, 1);
/*
* SD card (T_FLASH) detect and init
* T_FLASH_DETECT: EINT28: GPH3[4] input mode
*/
* SD card (T_FLASH) detect and init
* T_FLASH_DETECT: EINT28: GPH3[4] input mode
*/
+ gpio_request(S5PC110_GPIO_H34, "t_flash_detect");
gpio_cfg_pin(S5PC110_GPIO_H34, S5P_GPIO_INPUT);
gpio_set_pull(S5PC110_GPIO_H34, S5P_GPIO_PULL_UP);
gpio_cfg_pin(S5PC110_GPIO_H34, S5P_GPIO_INPUT);
gpio_set_pull(S5PC110_GPIO_H34, S5P_GPIO_PULL_UP);
static void board_enable_audio_codec(void)
{
/* Enable MAX98095 Codec */
static void board_enable_audio_codec(void)
{
/* Enable MAX98095 Codec */
+ gpio_request(EXYNOS5_GPIO_X17, "max98095_enable");
gpio_direction_output(EXYNOS5_GPIO_X17, 1);
gpio_set_pull(EXYNOS5_GPIO_X17, S5P_GPIO_PULL_NONE);
}
gpio_direction_output(EXYNOS5_GPIO_X17, 1);
gpio_set_pull(EXYNOS5_GPIO_X17, S5P_GPIO_PULL_NONE);
}
/* Setup the GPIOs */
/* PD is ACTIVE_LOW, and initially de-asserted */
/* Setup the GPIOs */
/* PD is ACTIVE_LOW, and initially de-asserted */
+ gpio_request(EXYNOS5_GPIO_Y25, "dp_bridge_pd");
gpio_set_pull(EXYNOS5_GPIO_Y25, S5P_GPIO_PULL_NONE);
gpio_direction_output(EXYNOS5_GPIO_Y25, 1);
/* Reset is ACTIVE_LOW */
gpio_set_pull(EXYNOS5_GPIO_Y25, S5P_GPIO_PULL_NONE);
gpio_direction_output(EXYNOS5_GPIO_Y25, 1);
/* Reset is ACTIVE_LOW */
+ gpio_request(EXYNOS5_GPIO_X15, "dp_bridge_reset");
gpio_set_pull(EXYNOS5_GPIO_X15, S5P_GPIO_PULL_NONE);
gpio_direction_output(EXYNOS5_GPIO_X15, 0);
udelay(10);
gpio_set_value(EXYNOS5_GPIO_X15, 1);
gpio_set_pull(EXYNOS5_GPIO_X15, S5P_GPIO_PULL_NONE);
gpio_direction_output(EXYNOS5_GPIO_X15, 0);
udelay(10);
gpio_set_value(EXYNOS5_GPIO_X15, 1);
+ gpio_request(EXYNOS5_GPIO_X07, "dp_bridge_hpd");
gpio_direction_input(EXYNOS5_GPIO_X07);
/*
gpio_direction_input(EXYNOS5_GPIO_X07);
/*
void exynos_cfg_lcd_gpio(void)
{
/* For Backlight */
void exynos_cfg_lcd_gpio(void)
{
/* For Backlight */
+ gpio_request(EXYNOS5_GPIO_B20, "lcd_backlight");
gpio_cfg_pin(EXYNOS5_GPIO_B20, S5P_GPIO_OUTPUT);
gpio_set_value(EXYNOS5_GPIO_B20, 1);
/* LCD power on */
gpio_cfg_pin(EXYNOS5_GPIO_B20, S5P_GPIO_OUTPUT);
gpio_set_value(EXYNOS5_GPIO_B20, 1);
/* LCD power on */
+ gpio_request(EXYNOS5_GPIO_X15, "lcd_power");
gpio_cfg_pin(EXYNOS5_GPIO_X15, S5P_GPIO_OUTPUT);
gpio_set_value(EXYNOS5_GPIO_X15, 1);
gpio_cfg_pin(EXYNOS5_GPIO_X15, S5P_GPIO_OUTPUT);
gpio_set_value(EXYNOS5_GPIO_X15, 1);
mdelay(10);
/* board_dp_backlight_en */
mdelay(10);
/* board_dp_backlight_en */
+ gpio_request(EXYNOS5_GPIO_X30, "board_dp_backlight_en");
gpio_direction_output(EXYNOS5_GPIO_X30, 1);
#endif
}
gpio_direction_output(EXYNOS5_GPIO_X30, 1);
#endif
}
mdelay(5);
/* TODO(ajaykumar.rs@samsung.com): Use device tree */
mdelay(5);
/* TODO(ajaykumar.rs@samsung.com): Use device tree */
+ gpio_request(EXYNOS5420_GPIO_X35, "edp_slp#");
gpio_direction_output(EXYNOS5420_GPIO_X35, 1); /* EDP_SLP# */
mdelay(10);
gpio_direction_output(EXYNOS5420_GPIO_X35, 1); /* EDP_SLP# */
mdelay(10);
+ gpio_request(EXYNOS5420_GPIO_Y77, "edp_rst#");
gpio_direction_output(EXYNOS5420_GPIO_Y77, 1); /* EDP_RST# */
gpio_direction_output(EXYNOS5420_GPIO_Y77, 1); /* EDP_RST# */
+ gpio_request(EXYNOS5420_GPIO_X26, "edp_hpd");
gpio_direction_input(EXYNOS5420_GPIO_X26); /* EDP_HPD */
gpio_set_pull(EXYNOS5420_GPIO_X26, S5P_GPIO_PULL_NONE);
gpio_direction_input(EXYNOS5420_GPIO_X26); /* EDP_HPD */
gpio_set_pull(EXYNOS5420_GPIO_X26, S5P_GPIO_PULL_NONE);
void exynos_backlight_on(unsigned int onoff)
{
/* For PWM */
void exynos_backlight_on(unsigned int onoff)
{
/* For PWM */
+ gpio_request(EXYNOS5420_GPIO_B20, "backlight_on");
gpio_cfg_pin(EXYNOS5420_GPIO_B20, S5P_GPIO_FUNC(0x1));
gpio_set_value(EXYNOS5420_GPIO_B20, 1);
gpio_cfg_pin(EXYNOS5420_GPIO_B20, S5P_GPIO_FUNC(0x1));
gpio_set_value(EXYNOS5420_GPIO_B20, 1);
+ gpio_request(EXYNOS4_GPIO_Y40, "i2c_clk");
+ gpio_request(EXYNOS4_GPIO_Y41, "i2c_data");
gpio_direction_output(EXYNOS4_GPIO_Y40, 1);
gpio_direction_output(EXYNOS4_GPIO_Y41, 1);
}
gpio_direction_output(EXYNOS4_GPIO_Y40, 1);
gpio_direction_output(EXYNOS4_GPIO_Y41, 1);
}
static unsigned int get_hw_revision(void)
{
int hwrev = 0;
static unsigned int get_hw_revision(void)
{
int hwrev = 0;
int i;
/* hw_rev[3:0] == GPE1[3:0] */
int i;
/* hw_rev[3:0] == GPE1[3:0] */
- for (i = EXYNOS4_GPIO_E10; i < EXYNOS4_GPIO_E14; i++) {
- gpio_cfg_pin(i, S5P_GPIO_INPUT);
- gpio_set_pull(i, S5P_GPIO_PULL_NONE);
+ for (i = 0; i < 4; i++) {
+ int pin = i + EXYNOS4_GPIO_E10;
+
+ sprintf(str, "hw_rev%d", i);
+ gpio_request(pin, str);
+ gpio_cfg_pin(pin, S5P_GPIO_INPUT);
+ gpio_set_pull(pin, S5P_GPIO_PULL_NONE);
static void exynos_uart_init(void)
{
/* UART_SEL GPY4[7] (part2) at EXYNOS4 */
static void exynos_uart_init(void)
{
/* UART_SEL GPY4[7] (part2) at EXYNOS4 */
+ gpio_request(EXYNOS4_GPIO_Y47, "uart_sel");
gpio_set_pull(EXYNOS4_GPIO_Y47, S5P_GPIO_PULL_UP);
gpio_direction_output(EXYNOS4_GPIO_Y47, 1);
}
gpio_set_pull(EXYNOS4_GPIO_Y47, S5P_GPIO_PULL_UP);
gpio_direction_output(EXYNOS4_GPIO_Y47, 1);
}
void exynos_reset_lcd(void)
{
void exynos_reset_lcd(void)
{
+ gpio_request(EXYNOS4_GPIO_Y45, "lcd_reset");
gpio_direction_output(EXYNOS4_GPIO_Y45, 1);
udelay(10000);
gpio_direction_output(EXYNOS4_GPIO_Y45, 0);
gpio_direction_output(EXYNOS4_GPIO_Y45, 1);
udelay(10000);
gpio_direction_output(EXYNOS4_GPIO_Y45, 0);
static void check_hw_revision(void)
{
int modelrev = 0;
static void check_hw_revision(void)
{
int modelrev = 0;
* TRM say that it may cause unexcepted state and leakage current.
* and pull-none is only for output function.
*/
* TRM say that it may cause unexcepted state and leakage current.
* and pull-none is only for output function.
*/
- for (i = EXYNOS4X12_GPIO_M10; i < EXYNOS4X12_GPIO_M12; i++)
- gpio_cfg_pin(i, S5P_GPIO_INPUT);
+ for (i = 0; i < 2; i++) {
+ int pin = i + EXYNOS4X12_GPIO_M10;
+
+ sprintf(str, "model_rev%d", i);
+ gpio_request(pin, str);
+ gpio_cfg_pin(pin, S5P_GPIO_INPUT);
+ }
/* GPM1[5:2]: HW_REV[3:0] */
/* GPM1[5:2]: HW_REV[3:0] */
- for (i = EXYNOS4X12_GPIO_M12; i < EXYNOS4X12_GPIO_M16; i++) {
- gpio_cfg_pin(i, S5P_GPIO_INPUT);
- gpio_set_pull(i, S5P_GPIO_PULL_NONE);
+ for (i = 0; i < 4; i++) {
+ int pin = i + EXYNOS4X12_GPIO_M12;
+
+ sprintf(str, "hw_rev%d", i);
+ gpio_request(pin, str);
+ gpio_cfg_pin(pin, S5P_GPIO_INPUT);
+ gpio_set_pull(pin, S5P_GPIO_PULL_NONE);
}
/* GPM1[1:0]: MODEL_REV[1:0] */
}
/* GPM1[1:0]: MODEL_REV[1:0] */
+ gpio_request(EXYNOS4X12_GPIO_F14, "i2c8_clk");
+ gpio_request(EXYNOS4X12_GPIO_F15, "i2c8_data");
gpio_direction_output(EXYNOS4X12_GPIO_F14, 1);
gpio_direction_output(EXYNOS4X12_GPIO_F15, 1);
/* I2C_9 */
gpio_direction_output(EXYNOS4X12_GPIO_F14, 1);
gpio_direction_output(EXYNOS4X12_GPIO_F15, 1);
/* I2C_9 */
+ gpio_request(EXYNOS4X12_GPIO_M21, "i2c9_clk");
+ gpio_request(EXYNOS4X12_GPIO_M20, "i2c9_data");
gpio_direction_output(EXYNOS4X12_GPIO_M21, 1);
gpio_direction_output(EXYNOS4X12_GPIO_M20, 1);
}
gpio_direction_output(EXYNOS4X12_GPIO_M21, 1);
gpio_direction_output(EXYNOS4X12_GPIO_M20, 1);
}
struct pmic *p = pmic_get("MAX77686_PMIC");
/* LCD_2.2V_EN: GPC0[1] */
struct pmic *p = pmic_get("MAX77686_PMIC");
/* LCD_2.2V_EN: GPC0[1] */
+ gpio_request(EXYNOS4X12_GPIO_C01, "lcd_2v2_en");
gpio_set_pull(EXYNOS4X12_GPIO_C01, S5P_GPIO_PULL_UP);
gpio_direction_output(EXYNOS4X12_GPIO_C01, 1);
gpio_set_pull(EXYNOS4X12_GPIO_C01, S5P_GPIO_PULL_UP);
gpio_direction_output(EXYNOS4X12_GPIO_C01, 1);
void exynos_reset_lcd(void)
{
/* reset lcd */
void exynos_reset_lcd(void)
{
/* reset lcd */
+ gpio_request(EXYNOS4X12_GPIO_F21, "lcd_reset");
gpio_direction_output(EXYNOS4X12_GPIO_F21, 0);
udelay(10);
gpio_set_value(EXYNOS4X12_GPIO_F21, 1);
gpio_direction_output(EXYNOS4X12_GPIO_F21, 0);
udelay(10);
gpio_set_value(EXYNOS4X12_GPIO_F21, 1);
}
/* gpio pad configuration for LCD reset. */
}
/* gpio pad configuration for LCD reset. */
+ gpio_request(EXYNOS4_GPIO_Y45, "lcd_reset");
gpio_cfg_pin(EXYNOS4_GPIO_Y45, S5P_GPIO_OUTPUT);
spi_init();
gpio_cfg_pin(EXYNOS4_GPIO_Y45, S5P_GPIO_OUTPUT);
spi_init();
* you should set it HIGH since it removes the inverter
*/
/* MASSMEMORY_EN: XMDMDATA_6: GPE3[6] */
* you should set it HIGH since it removes the inverter
*/
/* MASSMEMORY_EN: XMDMDATA_6: GPE3[6] */
+ gpio_request(EXYNOS4_GPIO_E36, "ldo_en");
gpio_direction_output(EXYNOS4_GPIO_E36, 0);
break;
default:
gpio_direction_output(EXYNOS4_GPIO_E36, 0);
break;
default:
* But set it as HIGH to ensure
*/
/* MASSMEMORY_EN: XMDMADDR_3: GPE1[3] */
* But set it as HIGH to ensure
*/
/* MASSMEMORY_EN: XMDMADDR_3: GPE1[3] */
+ gpio_request(EXYNOS4_GPIO_E13, "massmemory_en");
gpio_direction_output(EXYNOS4_GPIO_E13, 1);
break;
}
gpio_direction_output(EXYNOS4_GPIO_E13, 1);
break;
}
static int do_sdhci_init(struct sdhci_host *host)
{
static int do_sdhci_init(struct sdhci_host *host)
{
int dev_id, flag;
int err = 0;
int dev_id, flag;
int err = 0;
dev_id = host->index + PERIPH_ID_SDMMC0;
if (fdt_gpio_isvalid(&host->pwr_gpio)) {
dev_id = host->index + PERIPH_ID_SDMMC0;
if (fdt_gpio_isvalid(&host->pwr_gpio)) {
+ sprintf(str, "sdhci%d_power", host->index & 0xf);
+ gpio_request(host->pwr_gpio.gpio, str);
gpio_direction_output(host->pwr_gpio.gpio, 1);
err = exynos_pinmux_config(dev_id, flag);
if (err) {
gpio_direction_output(host->pwr_gpio.gpio, 1);
err = exynos_pinmux_config(dev_id, flag);
if (err) {
}
if (fdt_gpio_isvalid(&host->cd_gpio)) {
}
if (fdt_gpio_isvalid(&host->cd_gpio)) {
- gpio_direction_output(host->cd_gpio.gpio, 0xf);
+ sprintf(str, "sdhci%d_cd", host->index & 0xf);
+ gpio_request(host->cd_gpio.gpio, str);
+ gpio_direction_output(host->cd_gpio.gpio, 1);
if (gpio_get_value(host->cd_gpio.gpio))
return -ENODEV;
if (gpio_get_value(host->cd_gpio.gpio))
return -ENODEV;