printf("IPG %8d kHz\n", mxc_get_clock(MXC_IPG_CLK) / 1000);
printf("IPG PERCLK %8d kHz\n", mxc_get_clock(MXC_IPG_PERCLK) / 1000);
printf("DDR %8d kHz\n", mxc_get_clock(MXC_DDR_CLK) / 1000);
-
+#ifdef CONFIG_MXC_SPI
+ printf("CSPI %8d kHz\n", mxc_get_clock(MXC_CSPI_CLK) / 1000);
+#endif
return 0;
}
mov r10, lr
mov r4, #0 /* Fix R4 to 0 */
-#if defined(CONFIG_MX51)
+#if defined(CONFIG_SYS_MAIN_PWR_ON)
ldr r0, =GPIO1_BASE_ADDR
ldr r1, [r0, #0x0]
orr r1, r1, #1 << 23
printf("\n");
printf("IPG %8d kHz\n", mxc_get_clock(MXC_IPG_CLK) / 1000);
printf("UART %8d kHz\n", mxc_get_clock(MXC_UART_CLK) / 1000);
+#ifdef CONFIG_MXC_SPI
printf("CSPI %8d kHz\n", mxc_get_clock(MXC_CSPI_CLK) / 1000);
+#endif
printf("AHB %8d kHz\n", mxc_get_clock(MXC_AHB_CLK) / 1000);
printf("AXI %8d kHz\n", mxc_get_clock(MXC_AXI_CLK) / 1000);
printf("DDR %8d kHz\n", mxc_get_clock(MXC_DDR_CLK) / 1000);
#define IMX_RTIC_BASE (0x53FEC000)
#define IMX_IIM_BASE (0x53FF0000)
#define IMX_USB_BASE (0x53FF4000)
+#define IMX_USB_PORT_OFFSET 0x200
#define IMX_CSI_BASE (0x53FF8000)
#define IMX_DRYICE_BASE (0x53FFC000)
#define MX31_AIPS1_BASE_ADDR 0x43f00000
#define IMX_USB_BASE (MX31_AIPS1_BASE_ADDR + 0x88000)
-
-/* USB portsc */
-/* values for portsc field */
-#define MXC_EHCI_PHY_LOW_POWER_SUSPEND (1 << 23)
-#define MXC_EHCI_FORCE_FS (1 << 24)
-#define MXC_EHCI_UTMI_8BIT (0 << 28)
-#define MXC_EHCI_UTMI_16BIT (1 << 28)
-#define MXC_EHCI_SERIAL (1 << 29)
-#define MXC_EHCI_MODE_UTMI (0 << 30)
-#define MXC_EHCI_MODE_PHILIPS (1 << 30)
-#define MXC_EHCI_MODE_ULPI (2 << 30)
-#define MXC_EHCI_MODE_SERIAL (3 << 30)
-
-/* values for flags field */
-#define MXC_EHCI_INTERFACE_DIFF_UNI (0 << 0)
-#define MXC_EHCI_INTERFACE_DIFF_BI (1 << 0)
-#define MXC_EHCI_INTERFACE_SINGLE_UNI (2 << 0)
-#define MXC_EHCI_INTERFACE_SINGLE_BI (3 << 0)
-#define MXC_EHCI_INTERFACE_MASK (0xf)
-
-#define MXC_EHCI_POWER_PINS_ENABLED (1 << 5)
-#define MXC_EHCI_TTL_ENABLED (1 << 6)
-
-#define MXC_EHCI_INTERNAL_PHY (1 << 7)
-#define MXC_EHCI_IPPUE_DOWN (1 << 8)
-#define MXC_EHCI_IPPUE_UP (1 << 9)
+#define IMX_USB_PORT_OFFSET 0x200
/*
* CSPI register definitions
#define PWM_BASE_ADDR 0x53FE0000
#define RTIC_BASE_ADDR 0x53FEC000
#define IIM_BASE_ADDR 0x53FF0000
+#define IMX_USB_BASE 0x53FF4000
+#define IMX_USB_PORT_OFFSET 0x400
#define IMX_CCM_BASE CCM_BASE_ADDR
MX53_CSPI_IPP_CSPI_CLK_IN_SELECT_INPUT,
MX53_CSPI_IPP_IND_MISO_SELECT_INPUT,
MX53_CSPI_IPP_IND_MOSI_SELECT_INPUT,
+ MX53_CSPI_IPP_IND_SS_B_0_SELECT_INPUT,
MX53_CSPI_IPP_IND_SS_B_1_SELECT_INPUT,
MX53_CSPI_IPP_IND_SS_B_2_SELECT_INPUT,
MX53_CSPI_IPP_IND_SS_B_3_SELECT_INPUT,
- MX53_CSPI_IPP_IND_SS_B_4_SELECT_INPUT,
MX53_ECSPI1_IPP_CSPI_CLK_IN_SELECT_INPUT,
MX53_ECSPI1_IPP_IND_MISO_SELECT_INPUT,
MX53_ECSPI1_IPP_IND_MOSI_SELECT_INPUT,
+ MX53_ECSPI1_IPP_IND_SS_B_0_SELECT_INPUT,
MX53_ECSPI1_IPP_IND_SS_B_1_SELECT_INPUT,
MX53_ECSPI1_IPP_IND_SS_B_2_SELECT_INPUT,
MX53_ECSPI1_IPP_IND_SS_B_3_SELECT_INPUT,
- MX53_ECSPI1_IPP_IND_SS_B_4_SELECT_INPUT,
MX53_ECSPI2_IPP_CSPI_CLK_IN_SELECT_INPUT,
MX53_ECSPI2_IPP_IND_MISO_SELECT_INPUT,
MX53_ECSPI2_IPP_IND_MOSI_SELECT_INPUT,
+ MX53_ECSPI2_IPP_IND_SS_B_0_SELECT_INPUT,
MX53_ECSPI2_IPP_IND_SS_B_1_SELECT_INPUT,
- MX53_ECSPI2_IPP_IND_SS_B_2_SELECT_INPUT,
MX53_ESAI1_IPP_IND_FSR_SELECT_INPUT,
MX53_ESAI1_IPP_IND_FST_SELECT_INPUT,
MX53_ESAI1_IPP_IND_HCKR_SELECT_INPUT,
#define POWER_MINPWR_PWD_ANA_CMPS (1 << 10)
#define POWER_MINPWR_ENABLE_OSC (1 << 9)
#define POWER_MINPWR_SELECT_OSC (1 << 8)
-#define POWER_MINPWR_FBG_OFF (1 << 7)
+#define POWER_MINPWR_VBG_OFF (1 << 7)
#define POWER_MINPWR_DOUBLE_FETS (1 << 6)
#define POWER_MINPWR_HALFFETS (1 << 5)
#define POWER_MINPWR_LESSANA_I (1 << 4)
#define POWER_DCLIMITS_POSLIMIT_BUCK_MASK (0x7f << 8)
#define POWER_DCLIMITS_POSLIMIT_BUCK_OFFSET 8
#define POWER_DCLIMITS_NEGLIMIT_MASK 0x7f
-#define POWER_DCLIMITS_NETLIMIT_OFFSET 0
+#define POWER_DCLIMITS_NEGLIMIT_OFFSET 0
#define POWER_LOOPCTRL_TOGGLE_DIF (1 << 20)
#define POWER_LOOPCTRL_HYST_SIGN (1 << 19)
orr r1, r1, #0x00000C00
orr r1, r1, #0x00000003
str r1, [r0, #CLKCTL_CGR1]
+
+ ldr r1, [r0, #CLKCTL_CGR2]
+ orr r1, r1, #0x00C00000
+ str r1, [r0, #CLKCTL_CGR2]
.endm
.macro setup_sdram
mxc_request_iomux(MX35_PIN_CSPI1_SCLK, MUX_CONFIG_SION);
}
+static void setup_iomux_usbotg(void)
+{
+ int in_pad, out_pad;
+
+ /* Set up pins for USBOTG. */
+ mxc_request_iomux(MX35_PIN_USBOTG_PWR,
+ MUX_CONFIG_SION | MUX_CONFIG_FUNC);
+ mxc_request_iomux(MX35_PIN_USBOTG_OC,
+ MUX_CONFIG_SION | MUX_CONFIG_FUNC);
+
+ in_pad = PAD_CTL_DRV_3_3V | PAD_CTL_HYS_SCHMITZ | PAD_CTL_PKE_ENABLE |
+ PAD_CTL_PUE_PUD | PAD_CTL_100K_PD | PAD_CTL_ODE_CMOS |
+ PAD_CTL_DRV_NORMAL | PAD_CTL_SRE_SLOW;
+ out_pad = PAD_CTL_DRV_3_3V | PAD_CTL_HYS_CMOS | PAD_CTL_PKE_NONE |
+ PAD_CTL_ODE_CMOS | PAD_CTL_DRV_NORMAL | PAD_CTL_SRE_SLOW;
+
+ mxc_iomux_set_pad(MX35_PIN_USBOTG_PWR, out_pad);
+ mxc_iomux_set_pad(MX35_PIN_USBOTG_OC, in_pad);
+}
+
static void setup_iomux_fec(void)
{
int pad;
__raw_writel(readl(&ccm->rcsr) | MXC_CCM_RCSR_NFC_FMS, &ccm->rcsr);
setup_iomux_i2c();
+ setup_iomux_usbotg();
setup_iomux_fec();
setup_iomux_spi();
mode), which causes the effect of this failure to be much lower (in terms
of frequency deviation), avoiding system failure, or at least decreasing
the likelihood of system failure.
+
+1.2 CONFIG_SYS_MAIN_PWR_ON: Trigger MAIN_PWR_ON upon startup.
+ This option should be enabled for boards having a SYS_ON_OFF_CTL signal
+ connected to GPIO1[23] and triggering the MAIN_PWR_ON signal like in the
+ reference designs.
reg_ctrl = reg_read(®s->ctrl);
/* Reset spi */
- reg_write(®s->ctrl, 0);
- reg_write(®s->ctrl, (reg_ctrl | 0x1));
+ reg_write(®s->ctrl, (reg_ctrl & ~MXC_CSPICTRL_EN));
+ reg_write(®s->ctrl, (reg_ctrl | MXC_CSPICTRL_EN));
/*
* The following computation is taken directly from Freescale's code.
if (cs > 3) {
mxcs->gpio = cs >> 8;
cs &= 3;
- ret = gpio_direction_output(mxcs->gpio, 0);
+ ret = gpio_direction_output(mxcs->gpio, !(mxcs->ss_pol));
if (ret) {
printf("mxc_spi: cannot setup gpio %d\n", mxcs->gpio);
return -EINVAL;
return NULL;
}
+ mxcs->ss_pol = (mode & SPI_CS_HIGH) ? 1 : 0;
+
ret = decode_cs(mxcs, cs);
if (ret < 0) {
free(mxcs);
mxcs->slave.bus = bus;
mxcs->slave.cs = cs;
mxcs->base = spi_bases[bus];
- mxcs->ss_pol = (mode & SPI_CS_HIGH) ? 1 : 0;
ret = spi_cfg_mxc(mxcs, cs, max_hz, mode);
if (ret) {
#define MX5_USBOTHER_REGS_OFFSET 0x800
-#define MXC_OTG_OFFSET 0
-#define MXC_H1_OFFSET 0x200
-#define MXC_H2_OFFSET 0x400
+#define MXC_OTG_OFFSET 0
+#define MXC_H1_OFFSET 0x200
+#define MXC_H2_OFFSET 0x400
+#define MXC_H3_OFFSET 0x600
#define MXC_USBCTRL_OFFSET 0
#define MXC_USB_PHY_CTR_FUNC_OFFSET 0x8
#define MXC_USB_PHY_CTR_FUNC2_OFFSET 0xc
#define MXC_USB_CTRL_1_OFFSET 0x10
#define MXC_USBH2CTRL_OFFSET 0x14
+#define MXC_USBH3CTRL_OFFSET 0x18
/* USB_CTRL */
-#define MXC_OTG_UCTRL_OWIE_BIT (1 << 27) /* OTG wakeup intr enable */
-#define MXC_OTG_UCTRL_OPM_BIT (1 << 24) /* OTG power mask */
-#define MXC_H1_UCTRL_H1UIE_BIT (1 << 12) /* Host1 ULPI interrupt enable */
-#define MXC_H1_UCTRL_H1WIE_BIT (1 << 11) /* HOST1 wakeup intr enable */
-#define MXC_H1_UCTRL_H1PM_BIT (1 << 8) /* HOST1 power mask */
+/* OTG wakeup intr enable */
+#define MXC_OTG_UCTRL_OWIE_BIT (1 << 27)
+/* OTG power mask */
+#define MXC_OTG_UCTRL_OPM_BIT (1 << 24)
+/* OTG power pin polarity */
+#define MXC_OTG_UCTRL_O_PWR_POL_BIT (1 << 24)
+/* Host1 ULPI interrupt enable */
+#define MXC_H1_UCTRL_H1UIE_BIT (1 << 12)
+/* HOST1 wakeup intr enable */
+#define MXC_H1_UCTRL_H1WIE_BIT (1 << 11)
+/* HOST1 power mask */
+#define MXC_H1_UCTRL_H1PM_BIT (1 << 8)
+/* HOST1 power pin polarity */
+#define MXC_H1_UCTRL_H1_PWR_POL_BIT (1 << 8)
/* USB_PHY_CTRL_FUNC */
-#define MXC_OTG_PHYCTRL_OC_DIS_BIT (1 << 8) /* OTG Disable Overcurrent Event */
-#define MXC_H1_OC_DIS_BIT (1 << 5) /* UH1 Disable Overcurrent Event */
+/* OTG Polarity of Overcurrent */
+#define MXC_OTG_PHYCTRL_OC_POL_BIT (1 << 9)
+/* OTG Disable Overcurrent Event */
+#define MXC_OTG_PHYCTRL_OC_DIS_BIT (1 << 8)
+/* UH1 Polarity of Overcurrent */
+#define MXC_H1_OC_POL_BIT (1 << 6)
+/* UH1 Disable Overcurrent Event */
+#define MXC_H1_OC_DIS_BIT (1 << 5)
+/* OTG Power Pin Polarity */
+#define MXC_OTG_PHYCTRL_PWR_POL_BIT (1 << 3)
/* USBH2CTRL */
-#define MXC_H2_UCTRL_H2UIE_BIT (1 << 8)
-#define MXC_H2_UCTRL_H2WIE_BIT (1 << 7)
-#define MXC_H2_UCTRL_H2PM_BIT (1 << 4)
+#define MXC_H2_UCTRL_H2_OC_POL_BIT (1 << 31)
+#define MXC_H2_UCTRL_H2_OC_DIS_BIT (1 << 30)
+#define MXC_H2_UCTRL_H2UIE_BIT (1 << 8)
+#define MXC_H2_UCTRL_H2WIE_BIT (1 << 7)
+#define MXC_H2_UCTRL_H2PM_BIT (1 << 4)
+#define MXC_H2_UCTRL_H2_PWR_POL_BIT (1 << 4)
+
+/* USBH3CTRL */
+#define MXC_H3_UCTRL_H3_OC_POL_BIT (1 << 31)
+#define MXC_H3_UCTRL_H3_OC_DIS_BIT (1 << 30)
+#define MXC_H3_UCTRL_H3UIE_BIT (1 << 8)
+#define MXC_H3_UCTRL_H3WIE_BIT (1 << 7)
+#define MXC_H3_UCTRL_H3_PWR_POL_BIT (1 << 4)
/* USB_CTRL_1 */
-#define MXC_USB_CTRL_UH1_EXT_CLK_EN (1 << 25)
+#define MXC_USB_CTRL_UH1_EXT_CLK_EN (1 << 25)
/* USB pin configuration */
#define USB_PAD_CONFIG (PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST | \
if (flags & MXC_EHCI_INTERNAL_PHY) {
v = __raw_readl(usbother_base +
MXC_USB_PHY_CTR_FUNC_OFFSET);
+ if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)
+ v |= MXC_OTG_PHYCTRL_OC_POL_BIT;
+ else
+ v &= ~MXC_OTG_PHYCTRL_OC_POL_BIT;
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+ /* OC/USBPWR is used */
+ v &= ~MXC_OTG_PHYCTRL_OC_DIS_BIT;
+ else
/* OC/USBPWR is not used */
v |= MXC_OTG_PHYCTRL_OC_DIS_BIT;
+#ifdef CONFIG_MX51
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MXC_OTG_PHYCTRL_PWR_POL_BIT;
else
- /* OC/USBPWR is used */
- v &= ~MXC_OTG_PHYCTRL_OC_DIS_BIT;
+ v &= ~MXC_OTG_PHYCTRL_PWR_POL_BIT;
+#endif
__raw_writel(v, usbother_base +
MXC_USB_PHY_CTR_FUNC_OFFSET);
v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET);
+#ifdef CONFIG_MX51
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+ v &= ~MXC_OTG_UCTRL_OPM_BIT;
+ else
v |= MXC_OTG_UCTRL_OPM_BIT;
+#endif
+#ifdef CONFIG_MX53
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MXC_OTG_UCTRL_O_PWR_POL_BIT;
else
- v &= ~MXC_OTG_UCTRL_OPM_BIT;
+ v &= ~MXC_OTG_UCTRL_O_PWR_POL_BIT;
+#endif
__raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
}
break;
- case 1: /* Host 1 Host ULPI */
+ case 1: /* Host 1 ULPI */
#ifdef CONFIG_MX51
/* The clock for the USBH1 ULPI port will come externally
from the PHY. */
#endif
v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET);
+#ifdef CONFIG_MX51
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
- v &= ~MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used */
+ v &= ~MXC_H1_UCTRL_H1PM_BIT; /* H1 power mask unused */
else
- v |= MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used */
+ v |= MXC_H1_UCTRL_H1PM_BIT; /* H1 power mask used */
+#endif
+#ifdef CONFIG_MX53
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MXC_H1_UCTRL_H1_PWR_POL_BIT;
+ else
+ v &= ~MXC_H1_UCTRL_H1_PWR_POL_BIT;
+#endif
__raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET);
v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET);
+ if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)
+ v |= MXC_H1_OC_POL_BIT;
+ else
+ v &= ~MXC_H1_OC_POL_BIT;
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
v &= ~MXC_H1_OC_DIS_BIT; /* OC is used */
else
break;
case 2: /* Host 2 ULPI */
v = __raw_readl(usbother_base + MXC_USBH2CTRL_OFFSET);
+#ifdef CONFIG_MX51
if (flags & MXC_EHCI_POWER_PINS_ENABLED)
- v &= ~MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask used */
+ v &= ~MXC_H2_UCTRL_H2PM_BIT; /* H2 power mask unused */
else
- v |= MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask used */
-
+ v |= MXC_H2_UCTRL_H2PM_BIT; /* H2 power mask used */
+#endif
+#ifdef CONFIG_MX53
+ if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)
+ v |= MXC_H2_UCTRL_H2_OC_POL_BIT;
+ else
+ v &= ~MXC_H2_UCTRL_H2_OC_POL_BIT;
+ if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+ v &= ~MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is used */
+ else
+ v |= MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is not used */
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MXC_H2_UCTRL_H2_PWR_POL_BIT;
+ else
+ v &= ~MXC_H2_UCTRL_H2_PWR_POL_BIT;
+#endif
__raw_writel(v, usbother_base + MXC_USBH2CTRL_OFFSET);
break;
+#ifdef CONFIG_MX53
+ case 3: /* Host 3 ULPI */
+ v = __raw_readl(usbother_base + MXC_USBH3CTRL_OFFSET);
+ if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)
+ v |= MXC_H3_UCTRL_H3_OC_POL_BIT;
+ else
+ v &= ~MXC_H3_UCTRL_H3_OC_POL_BIT;
+ if (flags & MXC_EHCI_POWER_PINS_ENABLED)
+ v &= ~MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is used */
+ else
+ v |= MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is not used */
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MXC_H3_UCTRL_H3_PWR_POL_BIT;
+ else
+ v &= ~MXC_H3_UCTRL_H3_PWR_POL_BIT;
+ __raw_writel(v, usbother_base + MXC_USBH3CTRL_OFFSET);
+ break;
+#endif
}
return ret;
}
-void __board_ehci_hcd_postinit(struct usb_ehci *ehci, int port)
+int __weak board_ehci_hcd_init(int port)
{
+ return 0;
}
-void board_ehci_hcd_postinit(struct usb_ehci *ehci, int port)
- __attribute((weak, alias("__board_ehci_hcd_postinit")));
+void __weak board_ehci_hcd_postinit(struct usb_ehci *ehci, int port)
+{
+}
int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
__raw_writel(val, usbother_base + USB_H1_CTRL_OFFSET);
}
+int __weak board_ehci_hcd_init(int port)
+{
+ return 0;
+}
+
int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
struct usb_ehci *ehci;
#define USBCTRL_OTGBASE_OFFSET 0x600
-#ifdef CONFIG_MX25
-#define MX25_USB_CTRL_IP_PUE_DOWN_BIT (1<<6)
-#define MX25_USB_CTRL_HSTD_BIT (1<<5)
-#define MX25_USB_CTRL_USBTE_BIT (1<<4)
-#define MX25_USB_CTRL_OCPOL_OTG_BIT (1<<3)
-#endif
+#define MX25_OTG_SIC_SHIFT 29
+#define MX25_OTG_SIC_MASK (0x3 << MX25_OTG_SIC_SHIFT)
+#define MX25_OTG_PM_BIT (1 << 24)
+#define MX25_OTG_PP_BIT (1 << 11)
+#define MX25_OTG_OCPOL_BIT (1 << 3)
+
+#define MX25_H1_SIC_SHIFT 21
+#define MX25_H1_SIC_MASK (0x3 << MX25_H1_SIC_SHIFT)
+#define MX25_H1_PP_BIT (1 << 18)
+#define MX25_H1_PM_BIT (1 << 16)
+#define MX25_H1_IPPUE_UP_BIT (1 << 7)
+#define MX25_H1_IPPUE_DOWN_BIT (1 << 6)
+#define MX25_H1_TLL_BIT (1 << 5)
+#define MX25_H1_USBTE_BIT (1 << 4)
+#define MX25_H1_OCPOL_BIT (1 << 2)
-#ifdef CONFIG_MX31
#define MX31_OTG_SIC_SHIFT 29
#define MX31_OTG_SIC_MASK (0x3 << MX31_OTG_SIC_SHIFT)
#define MX31_OTG_PM_BIT (1 << 24)
#define MX31_H1_SIC_MASK (0x3 << MX31_H1_SIC_SHIFT)
#define MX31_H1_PM_BIT (1 << 8)
#define MX31_H1_DT_BIT (1 << 4)
-#endif
+
+#define MX35_OTG_SIC_SHIFT 29
+#define MX35_OTG_SIC_MASK (0x3 << MX35_OTG_SIC_SHIFT)
+#define MX35_OTG_PM_BIT (1 << 24)
+#define MX35_OTG_PP_BIT (1 << 11)
+#define MX35_OTG_OCPOL_BIT (1 << 3)
+
+#define MX35_H1_SIC_SHIFT 21
+#define MX35_H1_SIC_MASK (0x3 << MX35_H1_SIC_SHIFT)
+#define MX35_H1_PP_BIT (1 << 18)
+#define MX35_H1_PM_BIT (1 << 16)
+#define MX35_H1_IPPUE_UP_BIT (1 << 7)
+#define MX35_H1_IPPUE_DOWN_BIT (1 << 6)
+#define MX35_H1_TLL_BIT (1 << 5)
+#define MX35_H1_USBTE_BIT (1 << 4)
+#define MX35_H1_OCPOL_BIT (1 << 2)
static int mxc_set_usbcontrol(int port, unsigned int flags)
{
unsigned int v;
-#ifdef CONFIG_MX25
- v = MX25_USB_CTRL_IP_PUE_DOWN_BIT | MX25_USB_CTRL_HSTD_BIT |
- MX25_USB_CTRL_USBTE_BIT | MX25_USB_CTRL_OCPOL_OTG_BIT;
-#endif
+ v = readl(IMX_USB_BASE + USBCTRL_OTGBASE_OFFSET);
+#if defined(CONFIG_MX25)
+ switch (port) {
+ case 0: /* OTG port */
+ v &= ~(MX25_OTG_SIC_MASK | MX25_OTG_PM_BIT | MX25_OTG_PP_BIT |
+ MX25_OTG_OCPOL_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_OTG_SIC_SHIFT;
-#ifdef CONFIG_MX31
- v = readl(IMX_USB_BASE + USBCTRL_OTGBASE_OFFSET);
-
- switch (port) {
- case 0: /* OTG port */
- v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT);
- v |= (flags & MXC_EHCI_INTERFACE_MASK)
- << MX31_OTG_SIC_SHIFT;
- if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
- v |= MX31_OTG_PM_BIT;
-
- break;
- case 1: /* H1 port */
- v &= ~(MX31_H1_SIC_MASK | MX31_H1_PM_BIT |
- MX31_H1_DT_BIT);
- v |= (flags & MXC_EHCI_INTERFACE_MASK)
- << MX31_H1_SIC_SHIFT;
- if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
- v |= MX31_H1_PM_BIT;
-
- if (!(flags & MXC_EHCI_TTL_ENABLED))
- v |= MX31_H1_DT_BIT;
-
- break;
- case 2: /* H2 port */
- v &= ~(MX31_H2_SIC_MASK | MX31_H2_PM_BIT |
- MX31_H2_DT_BIT);
- v |= (flags & MXC_EHCI_INTERFACE_MASK)
- << MX31_H2_SIC_SHIFT;
- if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
- v |= MX31_H2_PM_BIT;
-
- if (!(flags & MXC_EHCI_TTL_ENABLED))
- v |= MX31_H2_DT_BIT;
-
- break;
- default:
- return -EINVAL;
- }
-#endif
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX25_OTG_PM_BIT;
+
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MX25_OTG_PP_BIT;
+
+ if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
+ v |= MX25_OTG_OCPOL_BIT;
+
+ break;
+ case 1: /* H1 port */
+ v &= ~(MX25_H1_SIC_MASK | MX25_H1_PM_BIT | MX25_H1_PP_BIT |
+ MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT |
+ MX25_H1_USBTE_BIT | MX25_H1_IPPUE_DOWN_BIT |
+ MX25_H1_IPPUE_UP_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_H1_SIC_SHIFT;
+
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX25_H1_PM_BIT;
+
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MX25_H1_PP_BIT;
+
+ if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
+ v |= MX25_H1_OCPOL_BIT;
+
+ if (!(flags & MXC_EHCI_TTL_ENABLED))
+ v |= MX25_H1_TLL_BIT;
+
+ if (flags & MXC_EHCI_INTERNAL_PHY)
+ v |= MX25_H1_USBTE_BIT;
+
+ if (flags & MXC_EHCI_IPPUE_DOWN)
+ v |= MX25_H1_IPPUE_DOWN_BIT;
+
+ if (flags & MXC_EHCI_IPPUE_UP)
+ v |= MX25_H1_IPPUE_UP_BIT;
+
+ break;
+ default:
+ return -EINVAL;
+ }
+#elif defined(CONFIG_MX31)
+ switch (port) {
+ case 0: /* OTG port */
+ v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX31_OTG_SIC_SHIFT;
+
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX31_OTG_PM_BIT;
+ break;
+ case 1: /* H1 port */
+ v &= ~(MX31_H1_SIC_MASK | MX31_H1_PM_BIT | MX31_H1_DT_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX31_H1_SIC_SHIFT;
+
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX31_H1_PM_BIT;
+
+ if (!(flags & MXC_EHCI_TTL_ENABLED))
+ v |= MX31_H1_DT_BIT;
+
+ break;
+ case 2: /* H2 port */
+ v &= ~(MX31_H2_SIC_MASK | MX31_H2_PM_BIT | MX31_H2_DT_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX31_H2_SIC_SHIFT;
+
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX31_H2_PM_BIT;
+
+ if (!(flags & MXC_EHCI_TTL_ENABLED))
+ v |= MX31_H2_DT_BIT;
+
+ break;
+ default:
+ return -EINVAL;
+ }
+#elif defined(CONFIG_MX35)
+ switch (port) {
+ case 0: /* OTG port */
+ v &= ~(MX35_OTG_SIC_MASK | MX35_OTG_PM_BIT | MX35_OTG_PP_BIT |
+ MX35_OTG_OCPOL_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX35_OTG_SIC_SHIFT;
+
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX35_OTG_PM_BIT;
+
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MX35_OTG_PP_BIT;
+
+ if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
+ v |= MX35_OTG_OCPOL_BIT;
+
+ break;
+ case 1: /* H1 port */
+ v &= ~(MX35_H1_SIC_MASK | MX35_H1_PM_BIT | MX35_H1_PP_BIT |
+ MX35_H1_OCPOL_BIT | MX35_H1_TLL_BIT |
+ MX35_H1_USBTE_BIT | MX35_H1_IPPUE_DOWN_BIT |
+ MX35_H1_IPPUE_UP_BIT);
+ v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX35_H1_SIC_SHIFT;
+
+ if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
+ v |= MX35_H1_PM_BIT;
+
+ if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
+ v |= MX35_H1_PP_BIT;
+
+ if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
+ v |= MX35_H1_OCPOL_BIT;
+
+ if (!(flags & MXC_EHCI_TTL_ENABLED))
+ v |= MX35_H1_TLL_BIT;
+
+ if (flags & MXC_EHCI_INTERNAL_PHY)
+ v |= MX35_H1_USBTE_BIT;
+
+ if (flags & MXC_EHCI_IPPUE_DOWN)
+ v |= MX35_H1_IPPUE_DOWN_BIT;
+
+ if (flags & MXC_EHCI_IPPUE_UP)
+ v |= MX35_H1_IPPUE_UP_BIT;
+
+ break;
+ default:
+ return -EINVAL;
+ }
+#else
+#error MXC EHCI USB driver not supported on this platform
+#endif
writel(v, IMX_USB_BASE + USBCTRL_OTGBASE_OFFSET);
+
return 0;
}
udelay(80);
ehci = (struct usb_ehci *)(IMX_USB_BASE +
- (0x200 * CONFIG_MXC_USB_PORT));
+ IMX_USB_PORT_OFFSET * CONFIG_MXC_USB_PORT);
*hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
*hcor = (struct ehci_hcor *)((uint32_t) *hccr +
HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
setbits_le32(&ehci->usbmode, CM_HOST);
__raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
mxc_set_usbcontrol(CONFIG_MXC_USB_PORT, CONFIG_MXC_USB_FLAGS);
+#ifdef CONFIG_MX35
+ /* Workaround for ENGcm11601 */
+ __raw_writel(0, &ehci->sbuscfg);
+#endif
udelay(10000);
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 1
#define CONFIG_LOADADDR 0x81000000 /* loadaddr env var */
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
*/
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 1
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_LOADADDR 0x42000000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_BOARD_LATE_INIT
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 1
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs_base=setenv bootargs console=ttymxc0,115200\0" \
#define CONFIG_NET_RETRY_COUNT 100
#define CONFIG_CMD_DATE
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
#define CONFIG_CMD_MMC
#define CONFIG_DOS_PARTITION
#define CONFIG_EFI_PARTITION
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 1
#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */
#define CONFIG_MXC_NAND_HWECC
#define CONFIG_SYS_NAND_LARGEPAGE
+/* EHCI driver */
+#define CONFIG_USB_EHCI
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_EHCI_MXC
+#define CONFIG_MXC_USB_PORT 0
+#define CONFIG_MXC_USB_FLAGS (MXC_EHCI_INTERFACE_DIFF_UNI | \
+ MXC_EHCI_POWER_PINS_ENABLED | \
+ MXC_EHCI_OC_PIN_ACTIVE_LOW)
+#define CONFIG_MXC_USB_PORTSC (MXC_EHCI_UTMI_16BIT | MXC_EHCI_MODE_UTMI)
+
/* mmc driver */
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_SYS_DDR_CLKSEL 0
#define CONFIG_SYS_CLKTL_CBCDR 0x59E35145
+#define CONFIG_SYS_MAIN_PWR_ON
#endif
#define CONFIG_CMD_DATE
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 1
#define CONFIG_ETHPRIME "FEC0"
#define CONFIG_SYS_DDR_CLKSEL 0
#define CONFIG_SYS_CLKTL_CBCDR 0x59E35100
+#define CONFIG_SYS_MAIN_PWR_ON
/*-----------------------------------------------------------------------
* FLASH and environment organization
#undef CONFIG_CMD_IMLS
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 1
#define CONFIG_ETHPRIME "FEC0"
#define CONFIG_CMD_BOOTZ
#undef CONFIG_CMD_IMLS
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 1
#define CONFIG_LOADADDR 0x10800000
#define CONFIG_SYS_TEXT_BASE 0x17800000
#undef CONFIG_CMD_IMLS
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 1
#define CONFIG_PREBOOT ""
/* 166 MHz DDR RAM */
#define CONFIG_SYS_DDR_CLKSEL 0
#define CONFIG_SYS_CLKTL_CBCDR 0x19239100
+#define CONFIG_SYS_MAIN_PWR_ON
#define CONFIG_SYS_NO_FLASH
#define CONFIG_USB_EHCI /* Enable EHCI USB support */
#define CONFIG_USB_EHCI_MXC
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_MXC_USB_PORT 2
-#define CONFIG_MXC_USB_PORTSC 0xC0000000
-#define CONFIG_MXC_USB_FLAGS 0
+#define CONFIG_MXC_USB_PORT 1
+#define CONFIG_MXC_USB_PORTSC MXC_EHCI_MODE_SERIAL
+#define CONFIG_MXC_USB_FLAGS (MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN)
#define CONFIG_EHCI_IS_TDI
#define CONFIG_USB_STORAGE
#define CONFIG_DOS_PARTITION
/*
* For MXC SOCs
*/
+
+/* values for portsc field */
+#define MXC_EHCI_PHY_LOW_POWER_SUSPEND (1 << 23)
+#define MXC_EHCI_FORCE_FS (1 << 24)
+#define MXC_EHCI_UTMI_8BIT (0 << 28)
+#define MXC_EHCI_UTMI_16BIT (1 << 28)
+#define MXC_EHCI_SERIAL (1 << 29)
+#define MXC_EHCI_MODE_UTMI (0 << 30)
+#define MXC_EHCI_MODE_PHILIPS (1 << 30)
+#define MXC_EHCI_MODE_ULPI (2 << 30)
+#define MXC_EHCI_MODE_SERIAL (3 << 30)
+
+/* values for flags field */
+#define MXC_EHCI_INTERFACE_DIFF_UNI (0 << 0)
+#define MXC_EHCI_INTERFACE_DIFF_BI (1 << 0)
+#define MXC_EHCI_INTERFACE_SINGLE_UNI (2 << 0)
+#define MXC_EHCI_INTERFACE_SINGLE_BI (3 << 0)
+#define MXC_EHCI_INTERFACE_MASK (0xf)
+
#define MXC_EHCI_POWER_PINS_ENABLED (1 << 5)
-#define MXC_EHCI_TTL_ENABLED (1 << 6)
-#define MXC_EHCI_INTERNAL_PHY (1 << 7)
+#define MXC_EHCI_PWR_PIN_ACTIVE_HIGH (1 << 6)
+#define MXC_EHCI_OC_PIN_ACTIVE_LOW (1 << 7)
+#define MXC_EHCI_TTL_ENABLED (1 << 8)
+
+#define MXC_EHCI_INTERNAL_PHY (1 << 9)
+#define MXC_EHCI_IPPUE_DOWN (1 << 10)
+#define MXC_EHCI_IPPUE_UP (1 << 11)
/* Board-specific initialization */
int board_ehci_hcd_init(int port);
projects / karo-tx-uboot.git / commitdiff