#include <linux/bch.h>
#include <linux/compiler.h>
#include <nand.h>
-#ifdef CONFIG_AM33XX
#include <asm/omap_elm.h>
-#endif
+
+#define BADBLOCK_MARKER_LENGTH 2
+#define SECTOR_BYTES 512
static uint8_t cs;
-static __maybe_unused struct nand_ecclayout hw_nand_oob =
- GPMC_NAND_HW_ECC_LAYOUT;
-static __maybe_unused struct nand_ecclayout hw_bch8_nand_oob =
- GPMC_NAND_HW_BCH8_ECC_LAYOUT;
+static __maybe_unused struct nand_ecclayout omap_ecclayout;
/*
* omap_nand_hwcontrol - Set the address pointers corretly for the
uint8_t type;
uint8_t nibbles;
struct bch_control *control;
+ enum omap_ecc ecc_scheme;
};
/* bch types */
{
uint32_t val;
uint32_t dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1;
-#ifdef CONFIG_AM33XX
uint32_t unused_length = 0;
-#endif
uint32_t wr_mode = BCH_WRAPMODE_6;
struct nand_bch_priv *bch = chip->priv;
/* Clear the ecc result registers, select ecc reg as 1 */
writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control);
-#ifdef CONFIG_AM33XX
- wr_mode = BCH_WRAPMODE_1;
+ if (bch->ecc_scheme == OMAP_ECC_BCH8_CODE_HW) {
+ wr_mode = BCH_WRAPMODE_1;
switch (bch->nibbles) {
case ECC_BCH4_NIBBLES:
val |= (unused_length << 22);
break;
}
-#else
+ } else {
/*
* This ecc_size_config setting is for BCH sw library.
*
* size1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area)
*/
val = (32 << 22) | (0 << 12);
-#endif
+ }
/* ecc size configuration */
writel(val, &gpmc_cfg->ecc_size_config);
}
/*
- * BCH8 support (needs ELM and thus AM33xx-only)
+ * BCH support using ELM module
*/
-#ifdef CONFIG_AM33XX
+#ifdef CONFIG_NAND_OMAP_ELM
/*
* omap_read_bch8_result - Read BCH result for BCH8 level
*
}
return 0;
}
-#endif /* CONFIG_AM33XX */
+#endif /* CONFIG_NAND_OMAP_ELM */
/*
* OMAP3 BCH8 support (with BCH library)
*/
-#ifdef CONFIG_NAND_OMAP_BCH8
+#ifdef CONFIG_BCH
/*
- * omap_calculate_ecc_bch - Read BCH ECC result
+ * omap_calculate_ecc_bch_sw - Read BCH ECC result
*
* @mtd: MTD device structure
* @dat: The pointer to data on which ecc is computed (unused here)
* @ecc: The ECC output buffer
*/
-static int omap_calculate_ecc_bch(struct mtd_info *mtd, const uint8_t *dat,
+static int omap_calculate_ecc_bch_sw(struct mtd_info *mtd, const uint8_t *dat,
uint8_t *ecc)
{
int ret = 0;
}
/**
- * omap_correct_data_bch - Decode received data and correct errors
+ * omap_correct_data_bch_sw - Decode received data and correct errors
* @mtd: MTD device structure
* @data: page data
* @read_ecc: ecc read from nand flash
* @calc_ecc: ecc read from HW ECC registers
*/
-static int omap_correct_data_bch(struct mtd_info *mtd, u_char *data,
+static int omap_correct_data_bch_sw(struct mtd_info *mtd, u_char *data,
u_char *read_ecc, u_char *calc_ecc)
{
int i, count;
chip_priv->control = NULL;
}
}
-#endif /* CONFIG_NAND_OMAP_BCH8 */
+#endif /* CONFIG_BCH */
+
+/**
+ * omap_select_ecc_scheme - configures driver for particular ecc-scheme
+ * @nand: NAND chip device structure
+ * @ecc_scheme: ecc scheme to configure
+ * @pagesize: number of main-area bytes per page of NAND device
+ * @oobsize: number of OOB/spare bytes per page of NAND device
+ */
+static int omap_select_ecc_scheme(struct nand_chip *nand,
+ enum omap_ecc ecc_scheme, unsigned int pagesize, unsigned int oobsize) {
+ struct nand_bch_priv *bch = nand->priv;
+ struct nand_ecclayout *ecclayout = nand->ecc.layout;
+ int eccsteps = pagesize / SECTOR_BYTES;
+ int i;
+
+ switch (ecc_scheme) {
+ case OMAP_ECC_HAM1_CODE_SW:
+ debug("nand: selected OMAP_ECC_HAM1_CODE_SW\n");
+ /* For this ecc-scheme, ecc.bytes, ecc.layout, ... are
+ * initialized in nand_scan_tail(), so just set ecc.mode */
+ bch_priv.control = NULL;
+ bch_priv.type = 0;
+ nand->ecc.mode = NAND_ECC_SOFT;
+ nand->ecc.layout = NULL;
+ nand->ecc.size = pagesize;
+ bch->ecc_scheme = OMAP_ECC_HAM1_CODE_SW;
+ break;
+
+ case OMAP_ECC_HAM1_CODE_HW:
+ debug("nand: selected OMAP_ECC_HAM1_CODE_HW\n");
+ /* check ecc-scheme requirements before updating ecc info */
+ if ((3 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) {
+ printf("nand: error: insufficient OOB: require=%d\n", (
+ (3 * eccsteps) + BADBLOCK_MARKER_LENGTH));
+ return -EINVAL;
+ }
+ bch_priv.control = NULL;
+ bch_priv.type = 0;
+ /* populate ecc specific fields */
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.strength = 1;
+ nand->ecc.size = SECTOR_BYTES;
+ nand->ecc.bytes = 3;
+ nand->ecc.hwctl = omap_enable_hwecc;
+ nand->ecc.correct = omap_correct_data;
+ nand->ecc.calculate = omap_calculate_ecc;
+ /* define ecc-layout */
+ ecclayout->eccbytes = nand->ecc.bytes * eccsteps;
+ for (i = 0; i < ecclayout->eccbytes; i++)
+ ecclayout->eccpos[i] = i + BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
+ BADBLOCK_MARKER_LENGTH;
+ bch->ecc_scheme = OMAP_ECC_HAM1_CODE_HW;
+ break;
+
+ case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
+#ifdef CONFIG_BCH
+ debug("nand: selected OMAP_ECC_BCH8_CODE_HW_DETECTION_SW\n");
+ /* check ecc-scheme requirements before updating ecc info */
+ if ((13 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) {
+ printf("nand: error: insufficient OOB: require=%d\n", (
+ (13 * eccsteps) + BADBLOCK_MARKER_LENGTH));
+ return -EINVAL;
+ }
+ /* check if BCH S/W library can be used for error detection */
+ bch_priv.control = init_bch(13, 8, 0x201b);
+ if (!bch_priv.control) {
+ printf("nand: error: could not init_bch()\n");
+ return -ENODEV;
+ }
+ bch_priv.type = ECC_BCH8;
+ /* populate ecc specific fields */
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.strength = 8;
+ nand->ecc.size = SECTOR_BYTES;
+ nand->ecc.bytes = 13;
+ nand->ecc.hwctl = omap_enable_ecc_bch;
+ nand->ecc.correct = omap_correct_data_bch_sw;
+ nand->ecc.calculate = omap_calculate_ecc_bch_sw;
+ /* define ecc-layout */
+ ecclayout->eccbytes = nand->ecc.bytes * eccsteps;
+ ecclayout->eccpos[0] = BADBLOCK_MARKER_LENGTH;
+ for (i = 1; i < ecclayout->eccbytes; i++) {
+ if (i % nand->ecc.bytes)
+ ecclayout->eccpos[i] =
+ ecclayout->eccpos[i - 1] + 1;
+ else
+ ecclayout->eccpos[i] =
+ ecclayout->eccpos[i - 1] + 2;
+ }
+ ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
+ BADBLOCK_MARKER_LENGTH;
+ omap_hwecc_init_bch(nand, NAND_ECC_READ);
+ bch->ecc_scheme = OMAP_ECC_BCH8_CODE_HW_DETECTION_SW;
+ break;
+#else
+ printf("nand: error: CONFIG_BCH required for ECC\n");
+ return -EINVAL;
+#endif
+
+ case OMAP_ECC_BCH8_CODE_HW:
+#ifdef CONFIG_NAND_OMAP_ELM
+ debug("nand: selected OMAP_ECC_BCH8_CODE_HW\n");
+ /* check ecc-scheme requirements before updating ecc info */
+ if ((14 * eccsteps) + BADBLOCK_MARKER_LENGTH > oobsize) {
+ printf("nand: error: insufficient OOB: require=%d\n", (
+ (14 * eccsteps) + BADBLOCK_MARKER_LENGTH));
+ return -EINVAL;
+ }
+ /* intialize ELM for ECC error detection */
+ elm_init();
+ bch_priv.type = ECC_BCH8;
+ /* populate ecc specific fields */
+ nand->ecc.mode = NAND_ECC_HW;
+ nand->ecc.strength = 8;
+ nand->ecc.size = SECTOR_BYTES;
+ nand->ecc.bytes = 14;
+ nand->ecc.hwctl = omap_enable_ecc_bch;
+ nand->ecc.correct = omap_correct_data_bch;
+ nand->ecc.calculate = omap_calculate_ecc_bch;
+ nand->ecc.read_page = omap_read_page_bch;
+ /* define ecc-layout */
+ ecclayout->eccbytes = nand->ecc.bytes * eccsteps;
+ for (i = 0; i < ecclayout->eccbytes; i++)
+ ecclayout->eccpos[i] = i + BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree[0].offset = i + BADBLOCK_MARKER_LENGTH;
+ ecclayout->oobfree[0].length = oobsize - ecclayout->eccbytes -
+ BADBLOCK_MARKER_LENGTH;
+ bch->ecc_scheme = OMAP_ECC_BCH8_CODE_HW;
+ break;
+#else
+ printf("nand: error: CONFIG_NAND_OMAP_ELM required for ECC\n");
+ return -EINVAL;
+#endif
+
+ default:
+ debug("nand: error: ecc scheme not enabled or supported\n");
+ return -EINVAL;
+ }
+ return 0;
+}
#ifndef CONFIG_SPL_BUILD
/*
* @eccstrength - the number of bits that could be corrected
* (1 - hamming, 4 - BCH4, 8 - BCH8, 16 - BCH16)
*/
-void omap_nand_switch_ecc(uint32_t hardware, uint32_t eccstrength)
+int __maybe_unused omap_nand_switch_ecc(uint32_t hardware, uint32_t eccstrength)
{
struct nand_chip *nand;
struct mtd_info *mtd;
+ int err = 0;
if (nand_curr_device < 0 ||
nand_curr_device >= CONFIG_SYS_MAX_NAND_DEVICE ||
!nand_info[nand_curr_device].name) {
- printf("Error: Can't switch ecc, no devices available\n");
- return;
+ printf("nand: error: no NAND devices found\n");
+ return -ENODEV;
}
mtd = &nand_info[nand_curr_device];
nand = mtd->priv;
-
nand->options |= NAND_OWN_BUFFERS;
-
- /* Reset ecc interface */
- nand->ecc.mode = NAND_ECC_NONE;
- nand->ecc.read_page = NULL;
- nand->ecc.write_page = NULL;
- nand->ecc.read_oob = NULL;
- nand->ecc.write_oob = NULL;
- nand->ecc.hwctl = NULL;
- nand->ecc.correct = NULL;
- nand->ecc.calculate = NULL;
- nand->ecc.strength = eccstrength;
-
/* Setup the ecc configurations again */
if (hardware) {
if (eccstrength == 1) {
- nand->ecc.mode = NAND_ECC_HW;
- nand->ecc.layout = &hw_nand_oob;
- nand->ecc.size = 512;
- nand->ecc.bytes = 3;
- nand->ecc.hwctl = omap_enable_hwecc;
- nand->ecc.correct = omap_correct_data;
- nand->ecc.calculate = omap_calculate_ecc;
- omap_hwecc_init(nand);
- printf("1-bit hamming HW ECC selected\n");
- }
-#if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8)
- else if (eccstrength == 8) {
- nand->ecc.mode = NAND_ECC_HW;
- nand->ecc.layout = &hw_bch8_nand_oob;
- nand->ecc.size = 512;
-#ifdef CONFIG_AM33XX
- nand->ecc.bytes = 14;
- nand->ecc.read_page = omap_read_page_bch;
-#else
- nand->ecc.bytes = 13;
-#endif
- nand->ecc.hwctl = omap_enable_ecc_bch;
- nand->ecc.correct = omap_correct_data_bch;
- nand->ecc.calculate = omap_calculate_ecc_bch;
- omap_hwecc_init_bch(nand, NAND_ECC_READ);
- printf("8-bit BCH HW ECC selected\n");
+ err = omap_select_ecc_scheme(nand,
+ OMAP_ECC_HAM1_CODE_HW,
+ mtd->writesize, mtd->oobsize);
+ } else if (eccstrength == 8) {
+ err = omap_select_ecc_scheme(nand,
+ OMAP_ECC_BCH8_CODE_HW,
+ mtd->writesize, mtd->oobsize);
+ } else {
+ printf("nand: error: unsupported ECC scheme\n");
+ return -EINVAL;
}
-#endif
} else {
- nand->ecc.mode = NAND_ECC_SOFT;
- /* Use mtd default settings */
- nand->ecc.layout = NULL;
- nand->ecc.size = 0;
- printf("SW ECC selected\n");
+ err = omap_select_ecc_scheme(nand, OMAP_ECC_HAM1_CODE_SW,
+ mtd->writesize, mtd->oobsize);
}
/* Update NAND handling after ECC mode switch */
- nand_scan_tail(mtd);
-
- nand->options &= ~NAND_OWN_BUFFERS;
+ if (!err)
+ err = nand_scan_tail(mtd);
+ return err;
}
#endif /* CONFIG_SPL_BUILD */
{
int32_t gpmc_config = 0;
cs = 0;
-
+ int err = 0;
/*
* xloader/Uboot's gpmc configuration would have configured GPMC for
* nand type of memory. The following logic scans and latches on to the
cs++;
}
if (cs >= GPMC_MAX_CS) {
- printf("NAND: Unable to find NAND settings in "
+ printf("nand: error: Unable to find NAND settings in "
"GPMC Configuration - quitting\n");
return -ENODEV;
}
nand->IO_ADDR_R = (void __iomem *)&gpmc_cfg->cs[cs].nand_dat;
nand->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_cmd;
-
- nand->cmd_ctrl = omap_nand_hwcontrol;
- nand->options = NAND_NO_PADDING | NAND_CACHEPRG;
+ nand->priv = &bch_priv;
+ nand->cmd_ctrl = omap_nand_hwcontrol;
+ nand->options |= NAND_NO_PADDING | NAND_CACHEPRG;
/* If we are 16 bit dev, our gpmc config tells us that */
if ((readl(&gpmc_cfg->cs[cs].config1) & 0x3000) == 0x1000)
nand->options |= NAND_BUSWIDTH_16;
nand->chip_delay = 100;
-
-#if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8)
-#ifdef CONFIG_AM33XX
- /* AM33xx uses the ELM */
- /* required in case of BCH */
- elm_init();
-#else
- /*
- * Whereas other OMAP based SoC do not have the ELM, they use the BCH
- * SW library.
- */
- bch_priv.control = init_bch(13, 8, 0x201b /* hw polynominal */);
- if (!bch_priv.control) {
- puts("Could not init_bch()\n");
- return -ENODEV;
- }
-#endif
- /* BCH info that will be correct for SPL or overridden otherwise. */
- nand->priv = &bch_priv;
-#endif
-
- /* Default ECC mode */
-#if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8)
- nand->ecc.mode = NAND_ECC_HW;
- nand->ecc.layout = &hw_bch8_nand_oob;
- nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE;
- nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES;
- nand->ecc.strength = 8;
- nand->ecc.hwctl = omap_enable_ecc_bch;
- nand->ecc.correct = omap_correct_data_bch;
- nand->ecc.calculate = omap_calculate_ecc_bch;
-#ifdef CONFIG_AM33XX
- nand->ecc.read_page = omap_read_page_bch;
-#endif
- omap_hwecc_init_bch(nand, NAND_ECC_READ);
-#else
-#if !defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_NAND_SOFTECC)
- nand->ecc.mode = NAND_ECC_SOFT;
+ nand->ecc.layout = &omap_ecclayout;
+
+ /* select ECC scheme */
+#if defined(CONFIG_NAND_OMAP_ELM)
+ err = omap_select_ecc_scheme(nand, OMAP_ECC_BCH8_CODE_HW,
+ CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE);
+#elif defined(CONFIG_NAND_OMAP_BCH8)
+ err = omap_select_ecc_scheme(nand, OMAP_ECC_BCH8_CODE_HW_DETECTION_SW,
+ CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE);
+#elif !defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_NAND_SOFTECC)
+ err = omap_select_ecc_scheme(nand, OMAP_ECC_HAM1_CODE_SW,
+ 0, 0);
#else
- nand->ecc.mode = NAND_ECC_HW;
- nand->ecc.layout = &hw_nand_oob;
- nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE;
- nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES;
- nand->ecc.hwctl = omap_enable_hwecc;
- nand->ecc.correct = omap_correct_data;
- nand->ecc.calculate = omap_calculate_ecc;
- nand->ecc.strength = 1;
- omap_hwecc_init(nand);
-#endif
+ err = omap_select_ecc_scheme(nand, OMAP_ECC_HAM1_CODE_HW,
+ CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE);
#endif
+ if (err)
+ return err;
#ifdef CONFIG_SPL_BUILD
if (nand->options & NAND_BUSWIDTH_16)
projects / karo-tx-uboot.git / commitdiff