]> git.kernelconcepts.de Git - karo-tx-uboot.git/commitdiff
TI DaVinci: Driver for the davinci SPI controller
authorSekhar Nori <nsekhar@ti.com>
Wed, 27 Jan 2010 16:10:40 +0000 (11:10 -0500)
committerTom Rix <Tom.Rix@windriver.com>
Sun, 31 Jan 2010 23:46:17 +0000 (17:46 -0600)
This adds a driver for the SPI controller found on davinci
based SoCs from Texas Instruments.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
drivers/spi/Makefile
drivers/spi/davinci_spi.c [new file with mode: 0644]
drivers/spi/davinci_spi.h [new file with mode: 0644]

index 824d8e740cae32d16f95abe18a397f175b707bf9..f112ed00d0c841f78e45566f3277b5547b9e5e61 100644 (file)
@@ -29,6 +29,7 @@ COBJS-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o
 COBJS-$(CONFIG_ATMEL_SPI) += atmel_spi.o
 COBJS-$(CONFIG_BFIN_SPI) += bfin_spi.o
 COBJS-$(CONFIG_CF_SPI) += cf_spi.o
+COBJS-$(CONFIG_DAVINCI_SPI) += davinci_spi.o
 COBJS-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o
 COBJS-$(CONFIG_MPC52XX_SPI) += mpc52xx_spi.o
 COBJS-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
diff --git a/drivers/spi/davinci_spi.c b/drivers/spi/davinci_spi.c
new file mode 100644 (file)
index 0000000..ebc7f80
--- /dev/null
@@ -0,0 +1,223 @@
+/*
+ * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Driver for SPI controller on DaVinci. Based on atmel_spi.c
+ * by Atmel Corporation
+ *
+ * Copyright (C) 2007 Atmel Corporation
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <spi.h>
+#include <malloc.h>
+#include <asm/io.h>
+#include <asm/arch/hardware.h>
+#include "davinci_spi.h"
+
+void spi_init()
+{
+       /* do nothing */
+}
+
+struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
+                       unsigned int max_hz, unsigned int mode)
+{
+       struct davinci_spi_slave        *ds;
+
+       if (!spi_cs_is_valid(bus, cs))
+               return NULL;
+
+       ds = malloc(sizeof(*ds));
+       if (!ds)
+               return NULL;
+
+       ds->slave.bus = bus;
+       ds->slave.cs = cs;
+       ds->regs = (struct davinci_spi_regs *)CONFIG_SYS_SPI_BASE;
+       ds->freq = max_hz;
+
+       return &ds->slave;
+}
+
+void spi_free_slave(struct spi_slave *slave)
+{
+       struct davinci_spi_slave *ds = to_davinci_spi(slave);
+
+       free(ds);
+}
+
+int spi_claim_bus(struct spi_slave *slave)
+{
+       struct davinci_spi_slave *ds = to_davinci_spi(slave);
+       unsigned int scalar, data1_reg_val = 0;
+
+       /* Enable the SPI hardware */
+       writel(SPIGCR0_SPIRST_MASK, &ds->regs->gcr0);
+       udelay(1000);
+       writel(SPIGCR0_SPIENA_MASK, &ds->regs->gcr0);
+
+       /* Set master mode, powered up and not activated */
+       writel(SPIGCR1_MASTER_MASK | SPIGCR1_CLKMOD_MASK, &ds->regs->gcr1);
+
+       /* CS, CLK, SIMO and SOMI are functional pins */
+       writel((SPIPC0_EN0FUN_MASK | SPIPC0_CLKFUN_MASK |
+               SPIPC0_DOFUN_MASK | SPIPC0_DIFUN_MASK), &ds->regs->pc0);
+
+       /* setup format */
+       scalar = ((CONFIG_SYS_SPI_CLK / ds->freq) - 1) & 0xFF;
+
+       /*
+        * Use following format:
+        *   character length = 8,
+        *   clock signal delayed by half clk cycle,
+        *   clock low in idle state - Mode 0,
+        *   MSB shifted out first
+        */
+       writel(8 | (scalar << SPIFMT_PRESCALE_SHIFT) |
+               (1 << SPIFMT_PHASE_SHIFT), &ds->regs->fmt0);
+
+       /* hold cs active at end of transfer until explicitly de-asserted */
+       data1_reg_val = (1 << SPIDAT1_CSHOLD_SHIFT) |
+                       (slave->cs << SPIDAT1_CSNR_SHIFT);
+       writel(data1_reg_val, &ds->regs->dat1);
+
+       /*
+        * Including a minor delay. No science here. Should be good even with
+        * no delay
+        */
+       writel((50 << SPI_C2TDELAY_SHIFT) |
+               (50 << SPI_T2CDELAY_SHIFT), &ds->regs->delay);
+
+       /* default chip select register */
+       writel(SPIDEF_CSDEF0_MASK, &ds->regs->def);
+
+       /* no interrupts */
+       writel(0, &ds->regs->int0);
+       writel(0, &ds->regs->lvl);
+
+       /* enable SPI */
+       writel((readl(&ds->regs->gcr1) | SPIGCR1_SPIENA_MASK), &ds->regs->gcr1);
+
+       return 0;
+}
+
+void spi_release_bus(struct spi_slave *slave)
+{
+       struct davinci_spi_slave *ds = to_davinci_spi(slave);
+
+       /* Disable the SPI hardware */
+       writel(SPIGCR0_SPIRST_MASK, &ds->regs->gcr0);
+}
+
+int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
+               const void *dout, void *din, unsigned long flags)
+{
+       struct davinci_spi_slave *ds = to_davinci_spi(slave);
+       unsigned int    len, data1_reg_val = readl(&ds->regs->dat1);
+       int             ret, i;
+       const u8        *txp = dout; /* dout can be NULL for read operation */
+       u8              *rxp = din;  /* din can be NULL for write operation */
+
+       ret = 0;
+
+       if (bitlen == 0)
+               /* Finish any previously submitted transfers */
+               goto out;
+
+       /*
+        * It's not clear how non-8-bit-aligned transfers are supposed to be
+        * represented as a stream of bytes...this is a limitation of
+        * the current SPI interface - here we terminate on receiving such a
+        * transfer request.
+        */
+       if (bitlen % 8) {
+               /* Errors always terminate an ongoing transfer */
+               flags |= SPI_XFER_END;
+               goto out;
+       }
+
+       len = bitlen / 8;
+
+       /* do an empty read to clear the current contents */
+       readl(&ds->regs->buf);
+
+       /* keep writing and reading 1 byte until done */
+       for (i = 0; i < len; i++) {
+               /* wait till TXFULL is asserted */
+               while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK);
+
+               /* write the data */
+               data1_reg_val &= ~0xFFFF;
+               if (txp) {
+                       data1_reg_val |= *txp;
+                       txp++;
+               }
+
+               /*
+                * Write to DAT1 is required to keep the serial transfer going.
+                * We just terminate when we reach the end.
+                */
+               if ((i == (len - 1)) && (flags & SPI_XFER_END)) {
+                       /* clear CS hold */
+                       writel(data1_reg_val &
+                               ~(1 << SPIDAT1_CSHOLD_SHIFT), &ds->regs->dat1);
+               } else {
+                       /* enable CS hold */
+                       data1_reg_val |= ((1 << SPIDAT1_CSHOLD_SHIFT) |
+                                       (slave->cs << SPIDAT1_CSNR_SHIFT));
+                       writel(data1_reg_val, &ds->regs->dat1);
+               }
+
+               /* read the data - wait for data availability */
+               while (readl(&ds->regs->buf) & SPIBUF_RXEMPTY_MASK);
+
+               if (rxp) {
+                       *rxp = readl(&ds->regs->buf) & 0xFF;
+                       rxp++;
+               } else {
+                       /* simply drop the read character */
+                       readl(&ds->regs->buf);
+               }
+       }
+       return 0;
+
+out:
+       if (flags & SPI_XFER_END) {
+               writel(data1_reg_val &
+                       ~(1 << SPIDAT1_CSHOLD_SHIFT), &ds->regs->dat1);
+       }
+       return 0;
+}
+
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+       return bus == 0 && cs == 0;
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+       /* do nothing */
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+       /* do nothing */
+}
+
diff --git a/drivers/spi/davinci_spi.h b/drivers/spi/davinci_spi.h
new file mode 100644 (file)
index 0000000..8d36a42
--- /dev/null
@@ -0,0 +1,101 @@
+/*
+ * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Register definitions for the DaVinci SPI Controller
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _DAVINCI_SPI_H_
+#define _DAVINCI_SPI_H_
+
+struct davinci_spi_regs {
+       dv_reg  gcr0;           /* 0x00 */
+       dv_reg  gcr1;           /* 0x04 */
+       dv_reg  int0;           /* 0x08 */
+       dv_reg  lvl;            /* 0x0c */
+       dv_reg  flg;            /* 0x10 */
+       dv_reg  pc0;            /* 0x14 */
+       dv_reg  pc1;            /* 0x18 */
+       dv_reg  pc2;            /* 0x1c */
+       dv_reg  pc3;            /* 0x20 */
+       dv_reg  pc4;            /* 0x24 */
+       dv_reg  pc5;            /* 0x28 */
+       dv_reg  rsvd[3];
+       dv_reg  dat0;           /* 0x38 */
+       dv_reg  dat1;           /* 0x3c */
+       dv_reg  buf;            /* 0x40 */
+       dv_reg  emu;            /* 0x44 */
+       dv_reg  delay;          /* 0x48 */
+       dv_reg  def;            /* 0x4c */
+       dv_reg  fmt0;           /* 0x50 */
+       dv_reg  fmt1;           /* 0x54 */
+       dv_reg  fmt2;           /* 0x58 */
+       dv_reg  fmt3;           /* 0x5c */
+       dv_reg  intvec0;        /* 0x60 */
+       dv_reg  intvec1;        /* 0x64 */
+};
+
+#define BIT(x)                 (1 << (x))
+
+/* SPIGCR0 */
+#define SPIGCR0_SPIENA_MASK    0x1
+#define SPIGCR0_SPIRST_MASK    0x0
+
+/* SPIGCR0 */
+#define SPIGCR1_CLKMOD_MASK    BIT(1)
+#define SPIGCR1_MASTER_MASK    BIT(0)
+#define SPIGCR1_SPIENA_MASK    BIT(24)
+
+/* SPIPC0 */
+#define SPIPC0_DIFUN_MASK      BIT(11)         /* SIMO */
+#define SPIPC0_DOFUN_MASK      BIT(10)         /* SOMI */
+#define SPIPC0_CLKFUN_MASK     BIT(9)          /* CLK */
+#define SPIPC0_EN0FUN_MASK     BIT(0)
+
+/* SPIFMT0 */
+#define SPIFMT_SHIFTDIR_SHIFT  20
+#define SPIFMT_POLARITY_SHIFT  17
+#define SPIFMT_PHASE_SHIFT     16
+#define SPIFMT_PRESCALE_SHIFT  8
+
+/* SPIDAT1 */
+#define SPIDAT1_CSHOLD_SHIFT   28
+#define SPIDAT1_CSNR_SHIFT     16
+
+/* SPIDELAY */
+#define SPI_C2TDELAY_SHIFT     24
+#define SPI_T2CDELAY_SHIFT     16
+
+/* SPIBUF */
+#define SPIBUF_RXEMPTY_MASK    BIT(31)
+#define SPIBUF_TXFULL_MASK     BIT(29)
+
+/* SPIDEF */
+#define SPIDEF_CSDEF0_MASK     BIT(0)
+
+struct davinci_spi_slave {
+       struct spi_slave slave;
+       struct davinci_spi_regs *regs;
+       unsigned int freq;
+};
+
+static inline struct davinci_spi_slave *to_davinci_spi(struct spi_slave *slave)
+{
+       return container_of(slave, struct davinci_spi_slave, slave);
+}
+
+#endif /* _DAVINCI_SPI_H_ */