#ifdef CONFIG_SYS_FSL_ERRATUM_A007212
check_erratum_a007212();
#endif
+#ifdef CONFIG_SYS_FSL_ERRATUM_A005434
+ puts("Work-around for Erratum A-005434 enabled\n");
+#endif
return 0;
}
CPU_TYPE_ENTRY(G4860, G4860, 0),
CPU_TYPE_ENTRY(G4060, G4060, 0),
CPU_TYPE_ENTRY(B4440, B4440, 0),
+ CPU_TYPE_ENTRY(B4460, B4460, 0),
CPU_TYPE_ENTRY(G4440, G4440, 0),
CPU_TYPE_ENTRY(B4420, B4420, 0),
CPU_TYPE_ENTRY(B4220, B4220, 0),
#define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
#define CONFIG_SYS_FSL_ERRATUM_A005125
+#ifndef CONFIG_USB_MAX_CONTROLLER_COUNT
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#endif
#elif defined(CONFIG_P1021)
#define CONFIG_MAX_CPUS 2
#define CONFIG_SYS_FSL_ESDHC_P1010_BROKEN_SDCLK
#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.2"
#define CONFIG_SYS_FSL_ERRATUM_A005125
+#define CONFIG_SYS_FSL_ERRATUM_A005434
#define CONFIG_SYS_FSL_ERRATUM_I2C_A004447
#define CONFIG_SYS_FSL_A004447_SVR_REV 0x11
#define CONFIG_ESDHC_HC_BLK_ADDR
#define SVR_C293 0x850030
#define SVR_B4860 0X868000
#define SVR_G4860 0x868001
+#define SVR_B4460 0x868003
#define SVR_G4060 0x868003
#define SVR_B4440 0x868100
#define SVR_G4440 0x868101
/* some boards with non-256-bytes EEPROM have special define */
/* for MAX_NUM_PORTS in board-specific file */
#ifndef MAX_NUM_PORTS
-#define MAX_NUM_PORTS 23
+#define MAX_NUM_PORTS 16
#endif
#define NXID_VERSION 1
#endif
u8 res_1[21]; /* 0x2b - 0x3f Reserved */
u8 mac_count; /* 0x40 Number of MAC addresses */
u8 mac_flag; /* 0x41 MAC table flags */
- u8 mac[MAX_NUM_PORTS][6]; /* 0x42 - x MAC addresses */
- u32 crc; /* x+1 CRC32 checksum */
+ u8 mac[MAX_NUM_PORTS][6]; /* 0x42 - 0xa1 MAC addresses */
+ u8 res_2[90]; /* 0xa2 - 0xfb Reserved */
+ u32 crc; /* 0xfc - 0xff CRC32 checksum */
#endif
} e;
# SPDX-License-Identifier: GPL-2.0+
#
+MINIMAL=
+
+ifdef CONFIG_SPL_BUILD
+ifdef CONFIG_SPL_INIT_MINIMAL
+MINIMAL=y
+endif
+endif
+
+ifdef MINIMAL
+
+obj-y += spl_minimal.o tlb.o law.o
+
+else
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
obj-y += p1_p2_rdb.o
+obj-$(CONFIG_PCI) += pci.o
+endif
obj-y += ddr.o
obj-y += law.o
-obj-$(CONFIG_PCI) += pci.o
obj-y += tlb.o
+
+endif
phys_size_t fixed_sdram (void)
{
- char buf[32];
fsl_ddr_cfg_regs_t ddr_cfg_regs;
size_t ddr_size;
struct cpu_type *cpu;
ulong ddr_freq, ddr_freq_mhz;
cpu = gd->arch.cpu;
- /* P1020 and it's derivatives support max 32bit DDR width */
- if (cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1011) {
- ddr_size = (CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 / 2);
- } else {
- ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
- }
+
+ ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+
#if defined(CONFIG_SYS_RAMBOOT)
return ddr_size;
#endif
ddr_freq = get_ddr_freq(0);
ddr_freq_mhz = ddr_freq / 1000000;
- printf("Configuring DDR for %s MT/s data rate\n",
- strmhz(buf, ddr_freq));
+ printf("Configuring DDR for %ld T/s data rate\n", ddr_freq);
if(ddr_freq_mhz <= 400)
memcpy(&ddr_cfg_regs, &ddr_cfg_regs_400, sizeof(ddr_cfg_regs));
else if(ddr_freq_mhz <= 800)
memcpy(&ddr_cfg_regs, &ddr_cfg_regs_800, sizeof(ddr_cfg_regs));
else
- panic("Unsupported DDR data rate %s MT/s data rate\n",
- strmhz(buf, ddr_freq));
+ panic("Unsupported DDR data rate %ld T/s\n", ddr_freq);
/* P1020 and it's derivatives support max 32bit DDR width */
if (cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1011) {
--- /dev/null
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <malloc.h>
+#include <mmc.h>
+#include <nand.h>
+#include <i2c.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define SYSCLK_MASK 0x00200000
+#define BOARDREV_MASK 0x10100000
+
+#define SYSCLK_66 66666666
+#define SYSCLK_100 100000000
+
+unsigned long get_board_sys_clk(ulong dummy)
+{
+ ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
+ u32 val_gpdat, sysclk_gpio;
+
+ val_gpdat = in_be32(&pgpio->gpdat);
+ sysclk_gpio = val_gpdat & SYSCLK_MASK;
+
+ if (sysclk_gpio == 0)
+ return SYSCLK_66;
+ else
+ return SYSCLK_100;
+
+ return 0;
+}
+
+phys_size_t get_effective_memsize(void)
+{
+ return CONFIG_SYS_L2_SIZE;
+}
+
+void board_init_f(ulong bootflag)
+{
+ u32 plat_ratio, bus_clk;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+ console_init_f();
+
+ /* Set pmuxcr to allow both i2c1 and i2c2 */
+ setbits_be32(&gur->pmuxcr, in_be32(&gur->pmuxcr) | 0x1000);
+ setbits_be32(&gur->pmuxcr,
+ in_be32(&gur->pmuxcr) | MPC85xx_PMUXCR_SD_DATA);
+
+ /* Read back the register to synchronize the write. */
+ in_be32(&gur->pmuxcr);
+
+#ifdef CONFIG_SPL_SPI_BOOT
+ clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA);
+#endif
+
+ /* initialize selected port with appropriate baud rate */
+ plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+ plat_ratio >>= 1;
+ bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+ gd->bus_clk = bus_clk;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ bus_clk / 16 / CONFIG_BAUDRATE);
+#ifdef CONFIG_SPL_MMC_BOOT
+ puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ puts("\nSPI Flash boot...\n");
+#endif
+
+ /* copy code to RAM and jump to it - this should not return */
+ /* NOTE - code has to be copied out of NAND buffer before
+ * other blocks can be read.
+ */
+ relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ /* Pointer is writable since we allocated a register for it */
+ gd = (gd_t *)CONFIG_SPL_GD_ADDR;
+ bd_t *bd;
+
+ memset(gd, 0, sizeof(gd_t));
+ bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t));
+ memset(bd, 0, sizeof(bd_t));
+ gd->bd = bd;
+ bd->bi_memstart = CONFIG_SYS_INIT_L2_ADDR;
+ bd->bi_memsize = CONFIG_SYS_L2_SIZE;
+
+ probecpu();
+ get_clocks();
+ mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+ CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_initialize(bd);
+#endif
+ /* relocate environment function pointers etc. */
+#ifdef CONFIG_SPL_NAND_BOOT
+ nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_NAND_BOOT
+ nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_SPI_BOOT
+ spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+
+ gd->env_addr = (ulong)(CONFIG_ENV_ADDR);
+ gd->env_valid = 1;
+
+ gd->ram_size = initdram(0);
+#ifdef CONFIG_SPL_NAND_BOOT
+ puts("Tertiary program loader running in sram...");
+#else
+ puts("Second program loader running in sram...\n");
+#endif
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ nand_boot();
+#endif
+}
--- /dev/null
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <asm/io.h>
+#include <nand.h>
+#include <linux/compiler.h>
+#include <asm/fsl_law.h>
+#include <fsl_ddr_sdram.h>
+#include <asm/global_data.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+#define SYSCLK_MASK 0x00200000
+#define BOARDREV_MASK 0x10100000
+
+#define SYSCLK_66 66666666
+#define SYSCLK_100 100000000
+
+unsigned long get_board_sys_clk(ulong dummy)
+{
+ ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
+ u32 val_gpdat, sysclk_gpio;
+
+ val_gpdat = in_be32(&pgpio->gpdat);
+ sysclk_gpio = val_gpdat & SYSCLK_MASK;
+
+ if (sysclk_gpio == 0)
+ return SYSCLK_66;
+ else
+ return SYSCLK_100;
+
+ return 0;
+}
+
+void board_init_f(ulong bootflag)
+{
+ u32 plat_ratio;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+#if defined(CONFIG_SYS_NAND_BR_PRELIM) && defined(CONFIG_SYS_NAND_OR_PRELIM)
+ set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM);
+ set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM);
+#endif
+
+ /* initialize selected port with appropriate baud rate */
+ plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+ plat_ratio >>= 1;
+ gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ gd->bus_clk / 16 / CONFIG_BAUDRATE);
+
+ puts("\nNAND boot... ");
+
+ /* copy code to RAM and jump to it - this should not return */
+ /* NOTE - code has to be copied out of NAND buffer before
+ * other blocks can be read.
+ */
+ relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ puts("\nSecond program loader running in sram...");
+ nand_boot();
+}
+
+void putc(char c)
+{
+ if (c == '\n')
+ NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
+
+ NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
+}
+
+void puts(const char *str)
+{
+ while (*str)
+ putc(*str++);
+}
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 1, BOOKE_PAGESZ_1M, 1),
+#ifndef CONFIG_SPL_BUILD
/* W**G* - Flash/promjet, localbus */
/* This will be changed to *I*G* after relocation to RAM. */
SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
0, 4, BOOKE_PAGESZ_256K, 1),
#endif /* #if defined(CONFIG_PCI) */
+#endif
/* *I*G - NAND */
SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, 6, BOOKE_PAGESZ_1M, 1),
-#if defined(CONFIG_SYS_RAMBOOT)
+#ifdef CONFIG_SYS_INIT_L2_ADDR
+ /* *I*G - L2SRAM */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G,
+ 0, 11, BOOKE_PAGESZ_256K, 1),
+#if CONFIG_SYS_L2_SIZE >= (256 << 10)
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
+ CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 12, BOOKE_PAGESZ_256K, 1),
+#endif
+#endif
+
+#if defined(CONFIG_SYS_RAMBOOT) || \
+ (defined(CONFIG_SPL) && !defined(CONFIG_SPL_COMMON_INIT_DDR))
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
MAS3_SX|MAS3_SW|MAS3_SR, 0,
0, 7, BOOKE_PAGESZ_1G, 1)
#ifdef CONFIG_DEEP_SLEEP
void board_mem_sleep_setup(void)
{
+ /* does not provide HW signals for power management */
+ CPLD_WRITE(misc_ctl_status, (CPLD_READ(misc_ctl_status) & ~0x40));
/* Disable MCKE isolation */
gpio_set_value(2, 0);
udelay(1);
Active powerpc mpc85xx - freescale t4qds T4240QDS_SECURE_BOOT T4240QDS:PPC_T4240,SECURE_BOOT Aneesh Bansal <aneesh.bansal@freescale.com>
Active powerpc mpc85xx - freescale t4qds T4240QDS_SPIFLASH T4240QDS:PPC_T4240,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF40000 -
Active powerpc mpc85xx - freescale t4qds T4240QDS_SRIO_PCIE_BOOT T4240QDS:PPC_T4240,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF40000 -
+Active powerpc mpc85xx - freescale t4rdb T4160RDB T4240RDB:PPC_T4160 Chunhe Lan <Chunhe.Lan@freescale.com>
Active powerpc mpc85xx - freescale t4rdb T4240RDB T4240RDB:PPC_T4240 Chunhe Lan <Chunhe.Lan@freescale.com>
Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD controlcenterd:36BIT,SDCARD Dirk Eibach <eibach@gdsys.de>
Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD_DEVELOP controlcenterd:36BIT,SDCARD,DEVELOP Dirk Eibach <eibach@gdsys.de>
#define MIIM_VSC8514_18G_QSGMII 0x80e0
#define MIIM_VSC8514_18G_CMDSTAT 0x8000
+/* Vitesse VSC8664 Control/Status Register */
+#define MIIM_VSC8664_SERDES_AND_SIGDET 0x13
+#define MIIM_VSC8664_ADDITIONAL_DEV 0x16
+#define MIIM_VSC8664_EPHY_CON 0x17
+#define MIIM_VSC8664_LED_CON 0x1E
+
+#define PHY_EXT_PAGE_ACCESS_EXTENDED 0x0001
+
/* CIS8201 */
static int vitesse_config(struct phy_device *phydev)
{
return 0;
}
+static int vsc8664_config(struct phy_device *phydev)
+{
+ u32 val;
+
+ /* Enable MAC interface auto-negotiation */
+ phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, 0);
+ val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_EPHY_CON);
+ val |= (1 << 13);
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_EPHY_CON, val);
+
+ phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS,
+ PHY_EXT_PAGE_ACCESS_EXTENDED);
+ val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_SERDES_AND_SIGDET);
+ val |= (1 << 11);
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_SERDES_AND_SIGDET, val);
+ phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, 0);
+
+ /* Enable LED blink */
+ val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_LED_CON);
+ val &= ~(1 << 2);
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8664_LED_CON, val);
+
+ genphy_config_aneg(phydev);
+
+ return 0;
+}
+
static struct phy_driver VSC8211_driver = {
.name = "Vitesse VSC8211",
.uid = 0xfc4b0,
.shutdown = &genphy_shutdown,
};
+static struct phy_driver VSC8664_driver = {
+ .name = "Vitesse VSC8664",
+ .uid = 0x70660,
+ .mask = 0xffff0,
+ .features = PHY_GBIT_FEATURES,
+ .config = &vsc8664_config,
+ .startup = &vitesse_startup,
+ .shutdown = &genphy_shutdown,
+};
+
/* Vitesse bought Cicada, so we'll put these here */
static struct phy_driver cis8201_driver = {
.name = "CIS8201",
phy_register(&VSC8574_driver);
phy_register(&VSC8514_driver);
phy_register(&VSC8662_driver);
+ phy_register(&VSC8664_driver);
phy_register(&cis8201_driver);
phy_register(&cis8204_driver);
u64 size)
{
u32 sz = (__ilog2_u64(size) - 1);
- u32 flag = PIWAR_EN | PIWAR_LOCAL |
- PIWAR_READ_SNOOP | PIWAR_WRITE_SNOOP;
+#ifdef CONFIG_SYS_FSL_ERRATUM_A005434
+ u32 flag = 0;
+#else
+ u32 flag = PIWAR_LOCAL;
+#endif
+
+ flag |= PIWAR_EN | PIWAR_READ_SNOOP | PIWAR_WRITE_SNOOP;
out_be32(&pi->pitar, r->phys_start >> 12);
out_be32(&pi->piwbar, r->bus_start >> 12);
if (!strncmp(phy_type, "utmi", 4)) {
#if defined(CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY)
- setbits_be32(&ehci->control, PHY_CLK_SEL_UTMI);
- setbits_be32(&ehci->control, UTMI_PHY_EN);
+ clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK,
+ PHY_CLK_SEL_UTMI);
+ clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK,
+ UTMI_PHY_EN);
udelay(1000); /* delay required for PHY Clk to appear */
#endif
out_le32(&(*hcor)->or_portsc[0], PORT_PTS_UTMI);
- setbits_be32(&ehci->control, USB_EN);
+ clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK,
+ USB_EN);
} else {
- setbits_be32(&ehci->control, PHY_CLK_SEL_ULPI);
- clrsetbits_be32(&ehci->control, UTMI_PHY_EN, USB_EN);
+ clrsetbits_be32(&ehci->control, CONTROL_REGISTER_W1C_MASK,
+ PHY_CLK_SEL_ULPI);
+ clrsetbits_be32(&ehci->control, UTMI_PHY_EN |
+ CONTROL_REGISTER_W1C_MASK, USB_EN);
udelay(1000); /* delay required for PHY Clk to appear */
if (!usb_phy_clk_valid(ehci))
return -EINVAL;
* for slave u-boot IMAGE instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
/*
* for slave UCODE and ENV instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
"ramdiskfile=b4860qds/ramdisk.uboot\0" \
"fdtaddr=c00000\0" \
"fdtfile=b4860qds/b4860qds.dtb\0" \
- "bdev=sda3\0" \
- "c=ffe\0"
+ "bdev=sda3\0"
/* For emulation this causes u-boot to jump to the start of the proof point
app code automatically */
#endif
/* Set up IFC registers for boot location NOR/NAND */
-#if defined(CONFIG_NAND)
+#if defined(CONFIG_NAND) || defined(CONFIG_NAND_SECBOOT)
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
#ifdef CONFIG_P1011RDB
#define CONFIG_P1011
+#define CONFIG_SYS_L2_SIZE (256 << 10)
#endif
#ifdef CONFIG_P1020RDB
#define CONFIG_P1020
+#define CONFIG_SYS_L2_SIZE (256 << 10)
#endif
#ifdef CONFIG_P2010RDB
#define CONFIG_P2010
+#define CONFIG_SYS_L2_SIZE (512 << 10)
#endif
#ifdef CONFIG_P2020RDB
#define CONFIG_P2020
-#endif
-
-#ifdef CONFIG_NAND
-#define CONFIG_NAND_U_BOOT 1
-#define CONFIG_RAMBOOT_NAND 1
-#ifdef CONFIG_NAND_SPL
-#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
-#else
-#define CONFIG_SYS_LDSCRIPT $(CPUDIR)/u-boot-nand.lds
-#define CONFIG_SYS_TEXT_BASE 0xf8f82000
-#endif /* CONFIG_NAND_SPL */
+#define CONFIG_SYS_L2_SIZE (512 << 10)
#endif
#ifdef CONFIG_SDCARD
-#define CONFIG_RAMBOOT_SDCARD 1
-#define CONFIG_SYS_TEXT_BASE 0x11000000
-#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SYS_TEXT_BASE 0x11001000
+#define CONFIG_SPL_TEXT_BASE 0xf8f81000
+#define CONFIG_SPL_PAD_TO 0x20000
+#define CONFIG_SPL_MAX_SIZE (128 * 1024)
+#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000)
+#define CONFIG_SYS_MMC_U_BOOT_START (0x11000000)
+#define CONFIG_SYS_MMC_U_BOOT_OFFS (129 << 10)
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#define CONFIG_SPL_MMC_BOOT
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_COMMON_INIT_DDR
+#endif
#endif
#ifdef CONFIG_SPIFLASH
-#define CONFIG_RAMBOOT_SPIFLASH 1
-#define CONFIG_SYS_TEXT_BASE 0x11000000
-#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_MINIMAL
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SYS_TEXT_BASE 0x11001000
+#define CONFIG_SPL_TEXT_BASE 0xf8f81000
+#define CONFIG_SPL_PAD_TO 0x20000
+#define CONFIG_SPL_MAX_SIZE (128 * 1024)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x11000000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x11000000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (128 << 10)
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#define CONFIG_SPL_SPI_BOOT
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_COMMON_INIT_DDR
+#endif
+#endif
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL
+#define CONFIG_TPL
+#ifdef CONFIG_TPL_BUILD
+#define CONFIG_SPL_NAND_BOOT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_NAND_INIT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SPL_MAX_SIZE (128 << 10)
+#define CONFIG_SPL_TEXT_BASE 0xf8f81000
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (832 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000)
+#define CONFIG_SYS_NAND_U_BOOT_START (0x11000000)
+#define CONFIG_SYS_NAND_U_BOOT_OFFS ((128 + 128) << 10)
+#elif defined(CONFIG_SPL_BUILD)
+#define CONFIG_SPL_INIT_MINIMAL
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_TEXT_BASE 0xff800000
+#define CONFIG_SPL_MAX_SIZE 4096
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST 0xf8f80000
+#define CONFIG_SYS_NAND_U_BOOT_START 0xf8f80000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10)
+#endif /* not CONFIG_TPL_BUILD */
+
+#define CONFIG_SPL_PAD_TO 0x20000
+#define CONFIG_TPL_PAD_TO 0x20000
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SYS_TEXT_BASE 0x11001000
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
#endif
#ifndef CONFIG_SYS_TEXT_BASE
#endif
#ifndef CONFIG_SYS_MONITOR_BASE
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
+#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
+#endif
/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_SYS_MEMTEST_END 0x1fffffff
#define CONFIG_PANIC_HANG /* do not reset board on panic */
- /*
- * Config the L2 Cache as L2 SRAM
- */
+/*
+ * Config the L2 Cache as L2 SRAM
+*/
+#if defined(CONFIG_SPL_BUILD)
+#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH)
#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
+#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000
+#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024)
+#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 116 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE (32 << 10)
+#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 148 * 1024)
+#if defined(CONFIG_P2020RDB)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (364 << 10)
+#else
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (108 << 10)
+#endif
+#elif defined(CONFIG_NAND)
+#ifdef CONFIG_TPL_BUILD
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
+#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000
+#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 192 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 208 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (48 << 10)
+#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 176 * 1024)
#else
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
+#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
+#define CONFIG_SPL_RELOC_TEXT_BASE (CONFIG_SYS_INIT_L2_END - 0x2000)
+#define CONFIG_SPL_RELOC_STACK ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
+#endif /* CONFIG_TPL_BUILD */
+#endif
#endif
-#define CONFIG_SYS_L2_SIZE (512 << 10)
-#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-
-#define CONFIG_SYS_CCSRBAR 0xffe00000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
-#if defined(CONFIG_NAND_SPL)
+#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-#define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR size on P1_P2 RDBs */
+#if defined(CONFIG_P1011RDB) || defined(CONFIG_P1020RDB)
+/*
+ * P1020 and it's derivatives support max 32bit DDR width
+ * So Reduce available DDR size
+*/
+#define CONFIG_SYS_SDRAM_SIZE 512
+#else
+#define CONFIG_SYS_SDRAM_SIZE 1024
+#endif
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#if defined(CONFIG_RAMBOOT_NAND) || defined(CONFIG_RAMBOOT_SDCARD) || \
- defined(CONFIG_RAMBOOT_SPIFLASH)
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/
-#ifndef CONFIG_NAND_SPL
-#define CONFIG_SYS_NAND_BASE 0xffa00000
+#define CONFIG_SYS_NAND_BASE 0xff800000
#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
+#define CONFIG_SYS_NAND_BASE_PHYS 0xfff800000ull
#else
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
#endif
-#else
-#define CONFIG_SYS_NAND_BASE 0xfff00000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_NAND_BASE_PHYS 0xffff00000ull
-#else
-#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
-#endif
-#endif
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
#define CONFIG_NAND_FSL_ELBC 1
#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
-/* NAND boot: 4K NAND loader config */
-#define CONFIG_SYS_NAND_SPL_SIZE 0x1000
-#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000)
-#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR)
-#define CONFIG_SYS_NAND_U_BOOT_START (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE)
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (0)
-#define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000)
-#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
-
/* NAND flash config */
#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
| OR_FCM_TRLX \
| OR_FCM_EHTR)
-#ifdef CONFIG_RAMBOOT_NAND
+#ifdef CONFIG_NAND
#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
#define CONFIG_SYS_BR1_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#ifdef CONFIG_NAND_SPL
+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
#define CONFIG_NS16550_MIN_FUNCTIONS
#endif
/*
* Environment
*/
-#if defined(CONFIG_SYS_RAMBOOT)
-#if defined(CONFIG_RAMBOOT_NAND)
- #define CONFIG_ENV_IS_IN_NAND 1
- #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
- #define CONFIG_ENV_OFFSET ((768*1024)+CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_RAMBOOT_SDCARD)
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10))
+#elif defined(CONFIG_SDCARD)
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_FSL_FIXED_MMC_LOCATION
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_SYS_MMC_ENV_DEV 0
-#elif defined(CONFIG_RAMBOOT_SPIFLASH)
- #define CONFIG_ENV_IS_IN_SPI_FLASH
- #define CONFIG_ENV_SPI_BUS 0
- #define CONFIG_ENV_SPI_CS 0
- #define CONFIG_ENV_SPI_MAX_HZ 10000000
- #define CONFIG_ENV_SPI_MODE 0
- #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
- #define CONFIG_ENV_SECT_SIZE 0x10000
- #define CONFIG_ENV_SIZE 0x2000
-#endif
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_OFFSET (512 * 0x800)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10))
+#elif defined(CONFIG_NAND)
+#ifdef CONFIG_TPL_BUILD
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10))
#else
- #define CONFIG_ENV_IS_IN_FLASH 1
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
- #define CONFIG_ENV_SIZE 0x2000
- #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#endif
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET (1024 * 1024)
+#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
+#elif defined(CONFIG_SYS_RAMBOOT)
+#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
+#define CONFIG_ENV_SIZE 0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#endif
+
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
* for slave u-boot IMAGE instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
/*
* for slave UCODE and ENV instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
"ramdiskfile=p2041rdb/ramdisk.uboot\0" \
"fdtaddr=c00000\0" \
"fdtfile=p2041rdb/p2041rdb.dtb\0" \
- "bdev=sda3\0" \
- "c=ffe\0"
+ "bdev=sda3\0"
#define CONFIG_HDBOOT \
"setenv bootargs root=/dev/$bdev rw " \
"ramdiskfile=t1040qds/ramdisk.uboot\0" \
"fdtaddr=c00000\0" \
"fdtfile=t1040qds/t1040qds.dtb\0" \
- "bdev=sda3\0" \
- "c=ffe\0"
+ "bdev=sda3\0"
#define CONFIG_LINUX \
"setenv bootargs root=/dev/ram rw " \
"ramdiskfile=" __stringify(RAMDISKFILE) "\0" \
"fdtaddr=c00000\0" \
"fdtfile=" __stringify(FDTFILE) "\0" \
- "bdev=sda3\0" \
- "c=ffe\0"
+ "bdev=sda3\0"
#define CONFIG_LINUX \
"setenv bootargs root=/dev/ram rw " \
* for slave u-boot IMAGE instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
/*
* for slave UCODE and ENV instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
"ramdiskfile=t2080qds/ramdisk.uboot\0" \
"fdtaddr=c00000\0" \
"fdtfile=t2080qds/t2080qds.dtb\0" \
- "bdev=sda3\0" \
- "c=ffe\0"
+ "bdev=sda3\0"
/*
* For emulation this causes u-boot to jump to the start of the
* for slave u-boot IMAGE instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
/*
* for slave UCODE and ENV instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
"ramdiskfile=t2080rdb/ramdisk.uboot\0" \
"fdtaddr=c00000\0" \
"fdtfile=t2080rdb/t2080rdb.dtb\0" \
- "bdev=sda3\0" \
- "c=ffe\0"
+ "bdev=sda3\0"
/*
* For emulation this causes u-boot to jump to the start of the
"ramdiskfile=t4240emu/ramdisk.uboot\0" \
"fdtaddr=c00000\0" \
"fdtfile=t4240emu/t4240emu.dtb\0" \
- "bdev=sda3\0" \
- "c=ffe\0"
+ "bdev=sda3\0"
/*
* For emulation this causes u-boot to jump to the start of the proof point
* for slave u-boot IMAGE instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
/*
* for slave UCODE and ENV instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
"ramdiskfile=t4240qds/ramdisk.uboot\0" \
"fdtaddr=c00000\0" \
"fdtfile=t4240qds/t4240qds.dtb\0" \
- "bdev=sda3\0" \
- "c=ffe\0"
+ "bdev=sda3\0"
#define CONFIG_HVBOOT \
"setenv bootargs config-addr=0x60000000; " \
* interleaving. It can be cacheline, page, bank, superbank.
* See doc/README.fsl-ddr for details.
*/
+#ifdef CONFIG_PPC_T4240
#define CTRL_INTLV_PREFERED 3way_4KB
+#else
+#define CTRL_INTLV_PREFERED cacheline
+#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:" \
* for slave u-boot IMAGE instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
/*
* for slave UCODE and ENV instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
"ramdiskfile=p4080ds/ramdisk.uboot\0" \
"fdtaddr=c00000\0" \
"fdtfile=p4080ds/p4080ds.dtb\0" \
- "bdev=sda3\0" \
- "c=ffe\0"
+ "bdev=sda3\0"
#define CONFIG_HDBOOT \
"setenv bootargs root=/dev/$bdev rw " \
#endif
#endif
+#if defined(CONFIG_P1020RDB_PD)
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+#endif
+
#define CONFIG_MMC
#ifdef CONFIG_MMC
#include <asm/processor.h>
+#define CONTROL_REGISTER_W1C_MASK 0x00020000 /* W1C: PHY_CLK_VALID */
+
/* Global offsets */
#define FSL_SKIP_PCI 0x100
+++ /dev/null
-#
-# (C) Copyright 2007
-# Stefan Roese, DENX Software Engineering, sr@denx.de.
-#
-# Copyright 2009-2011 Freescale Semiconductor, Inc.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-CONFIG_SYS_TEXT_BASE_SPL := 0xfff00000
-PAD_TO := 0xfff01000
-
-nandobj := $(objtree)/nand_spl/
-
-LDSCRIPT= $(srctree)/$(CPUDIR)/u-boot-nand_spl.lds
-LDFLAGS := -T $(nandobj)u-boot-nand_spl.lds -Ttext $(CONFIG_SYS_TEXT_BASE_SPL) \
- $(LDFLAGS) $(LDFLAGS_FINAL)
-asflags-y += -DCONFIG_NAND_SPL
-ccflags-y += -DCONFIG_NAND_SPL
-
-SOBJS = start.o resetvec.o
-COBJS = cache.o cpu_init_early.o spl_minimal.o fsl_law.o law.o \
- nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o
-
-OBJS := $(addprefix $(obj)/,$(SOBJS) $(COBJS))
-__OBJS := $(SOBJS) $(COBJS)
-LNDIR := $(nandobj)board/$(BOARDDIR)
-
-targets += $(__OBJS)
-
-all: $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
-
-$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
- $(OBJCOPY) $(OBJCOPYFLAGS) --pad-to=$(PAD_TO) -O binary $< $@
-
-$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl
- $(OBJCOPY) $(OBJCOPYFLAGS) -O binary $< $@
-
-$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot-nand_spl.lds
- cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \
- -Map $(nandobj)u-boot-spl.map -o $@
-
-$(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT)
- $(CPP) $(cpp_flags) $(LDPPFLAGS) -I$(nandobj)/board/$(BOARDDIR) \
- -ansi -D__ASSEMBLY__ -P - <$< >$@
-
-# create symbolic links for common files
-
-$(obj)/cache.c:
- @rm -f $@
- ln -sf $(srctree)/arch/powerpc/lib/cache.c $@
-
-$(obj)/cpu_init_early.c:
- @rm -f $@
- ln -sf $(srctree)/arch/powerpc/cpu/mpc85xx/cpu_init_early.c $@
-
-$(obj)/spl_minimal.c:
- @rm -f $@
- ln -sf $(srctree)/arch/powerpc/cpu/mpc85xx/spl_minimal.c $@
-
-$(obj)/fsl_law.c:
- @rm -f $@
- ln -sf $(srctree)/arch/powerpc/cpu/mpc8xxx/law.c $@
-
-$(obj)/law.c:
- @rm -f $@
- ln -sf $(srctree)/board/$(BOARDDIR)/law.c $@
-
-$(obj)/nand_boot_fsl_elbc.c:
- @rm -f $@
- ln -sf $(srctree)/nand_spl/nand_boot_fsl_elbc.c $@
-
-$(obj)/ns16550.c:
- @rm -f $@
- ln -sf $(srctree)/drivers/serial/ns16550.c $@
-
-$(obj)/resetvec.S:
- @rm -f $@
- ln -s $(srctree)/$(CPUDIR)/resetvec.S $@
-
-$(obj)/start.S:
- @rm -f $@
- ln -sf $(srctree)/arch/powerpc/cpu/mpc85xx/start.S $@
-
-$(obj)/tlb.c:
- @rm -f $@
- ln -sf $(srctree)/arch/powerpc/cpu/mpc85xx/tlb.c $@
-
-$(obj)/tlb_table.c:
- @rm -f $@
- ln -sf $(srctree)/board/$(BOARDDIR)/tlb.c $@
+++ /dev/null
-/*
- * Copyright 2009 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#include <common.h>
-#include <mpc85xx.h>
-#include <asm/io.h>
-#include <ns16550.h>
-#include <nand.h>
-#include <asm/mmu.h>
-#include <asm/immap_85xx.h>
-#include <fsl_ddr_sdram.h>
-#include <asm/fsl_law.h>
-
-#define SYSCLK_MASK 0x00200000
-#define BOARDREV_MASK 0x10100000
-#define BOARDREV_B 0x10100000
-#define BOARDREV_C 0x00100000
-
-#define SYSCLK_66 66666666
-#define SYSCLK_50 50000000
-#define SYSCLK_100 100000000
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void board_init_f(ulong bootflag)
-{
- uint plat_ratio, bus_clk, sys_clk = 0;
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- volatile ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
- uint val, temp, sysclk_mask;
-
- val = pgpio->gpdat;
- sysclk_mask = val & SYSCLK_MASK;
- temp = val & BOARDREV_MASK;
- if (temp == BOARDREV_C) {
- if(sysclk_mask == 0)
- sys_clk = SYSCLK_66;
- else
- sys_clk = SYSCLK_100;
- } else if (temp == BOARDREV_B) {
- if(sysclk_mask == 0)
- sys_clk = SYSCLK_66;
- else
- sys_clk = SYSCLK_50;
- }
-
- plat_ratio = gur->porpllsr & 0x0000003e;
- plat_ratio >>= 1;
- bus_clk = plat_ratio * sys_clk;
- NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
- bus_clk / 16 / CONFIG_BAUDRATE);
-
- puts("\nNAND boot... ");
-
- /* copy code to DDR and jump to it - this should not return */
- /* NOTE - code has to be copied out of NAND buffer before
- * other blocks can be read.
- */
- relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, 0,
- CONFIG_SYS_NAND_U_BOOT_RELOC);
-}
-
-void board_init_r(gd_t *gd, ulong dest_addr)
-{
- nand_boot();
-}
-
-void putc(char c)
-{
- if (c == '\n')
- NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
-
- NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
-}
-
-void puts(const char *str)
-{
- while (*str)
- putc(*str++);
-}
projects / karo-tx-uboot.git / commitdiff