From: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Date: Tue, 11 Jun 2013 15:34:22 +0000 (-0500)
Subject: fsl_esdhc: Do not clear interrupt status bits until data processed
X-Git-Tag: v2013.07-rc2~96^2~4
X-Git-Url: https://git.kernelconcepts.de/?p=karo-tx-uboot.git;a=commitdiff_plain;h=01b77353e45f99daf3b3e598b9addf9365c7c47a

fsl_esdhc: Do not clear interrupt status bits until data processed

After waiting for the command completion event, the interrupt status
bits, that occured to be set by that time, are cleared by writing them
back. It is supposed, that it should be command related bits (command
complete and may be command errors).

However, in some cases the DMA already completes by that time before
the full transaction completes. The corresponding DINT bit gets set
and then cleared before even entering the loop, waiting for data part
completion. That waiting loop never gets this bit set, causing the
operation to hang. This is reported to happen, for example, for write
operation of 1 sector to upper area (block #7400000) of SanDisk Ultra II
8GB card.

The solution could be to explicitly clear only command related interrupt
status bits. However, since subsequent processing does not rely on
any command bits state, it could be easier just to remove clearing
of any bits at that point, leaving them all until all data processing
completes. After that the whole register will be cleared at once.

Also, on occasion, interrupts masking moved to before writing the command,
just for the case there should be no chance of interrupt between the first
command and interrupts masking.

Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
---

diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
index ec01795f32..973b19f337 100644
--- a/drivers/mmc/fsl_esdhc.c
+++ b/drivers/mmc/fsl_esdhc.c
@@ -310,6 +310,9 @@ esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
 	/* Figure out the transfer arguments */
 	xfertyp = esdhc_xfertyp(cmd, data);
 
+	/* Mask all irqs */
+	esdhc_write32(&regs->irqsigen, 0);
+
 	/* Send the command */
 	esdhc_write32(&regs->cmdarg, cmd->cmdarg);
 #if defined(CONFIG_FSL_USDHC)
@@ -320,15 +323,11 @@ esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
 	esdhc_write32(&regs->xfertyp, xfertyp);
 #endif
 
-	/* Mask all irqs */
-	esdhc_write32(&regs->irqsigen, 0);
-
 	/* Wait for the command to complete */
 	while (!(esdhc_read32(&regs->irqstat) & (IRQSTAT_CC | IRQSTAT_CTOE)))
 		;
 
 	irqstat = esdhc_read32(&regs->irqstat);
-	esdhc_write32(&regs->irqstat, irqstat);
 
 	/* Reset CMD and DATA portions on error */
 	if (irqstat & (CMD_ERR | IRQSTAT_CTOE)) {