Wolfgang Denk [Sun, 27 Nov 2011 15:03:21 +0000 (16:03 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-mmc
* 'master' of git://git.denx.de/u-boot-mmc:
Revert "mmc: retry the cmd8 to meet 74 clocks requirement in the spec"
mmc: mv_sdhci: Fix host version read for Armada100
Stephan Linz [Thu, 24 Nov 2011 12:32:52 +0000 (12:32 +0000)]
microblaze: usable uart16550 for big endian systems
As a result of the commit 6833260 the uart16550 driver
is broken for Microblaze big endian systems, because of
the missing 3 byte offset. Other than as described, not
all U-Boot BSP will treat properly the 3 byte offset.
This why prefer to mask out the 3 byte offset in general
and setup correct _REG_SIZE value depending on edianess.
Signed-off-by: Stephan Linz <linz@li-pro.net> Tested-by: Michal Simek <monstr@monstr.eu>
This patch add 3 times retry to CMD8 because the Marvell mmc controller
doesn't obey the power ramp up process in the SD specification 6.4.1.
(Please refer to figure 6.1 and 6.2 in the specification.)
The CMD0 should be send after power ramp up has been finished.
However, the Marvell mmc contorller must do power ramp up after the
first CMD0 command has been send.
This patch also affect existing platforms like Nokia N900 and other
platforms.
Signed-off-by: Macpaul Lin <macpaul@andestech.com> Acked-by: Lei Wen <leiwen@marvell.com> Acked-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com>
Fix:
dnet.c: In function 'dnet_send':
dnet.c:136:9: warning: variable 'len' set but not used
[-Wunused-but-set-variable]
dnet.c: In function 'dnet_set_hwaddr':
dnet.c:209:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
dnet.c:209:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
dnet.c:209:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
dnet.c:209:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
Fix:
flash.c: In function 'flash_erase':
flash.c:223:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:392:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Fix:
syncflash.c: In function 'SF_SR':
syncflash.c:60:10: warning: variable 'tmp1' set but not used
[-Wunused-but-set-variable]
syncflash.c: In function 'SF_PrechargeAll':
syncflash.c:96:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
mx1ads.c: In function 'board_early_init_f':
mx1ads.c:83:24: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
syncflash.c: In function 'SF_Erase':
syncflash.c:112:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
syncflash.c: In function 'flash_init':
syncflash.c:155:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
Fix:
flash.c: In function 'flash_erase':
flash.c:223:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:392:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable]
Fix:
cpuinfo.c: In function 'print_cpuinfo':
cpuinfo.c:155:6: warning: variable 'system_serial_low' set but not used
[-Wunused-but-set-variable]
cpuinfo.c:154:6: warning: variable 'system_serial_high' set but not used
[-Wunused-but-set-variable]
Fix:
lan91c96.c: In function 'dump_memory_info':
lan91c96.c:157:7: warning: variable 'mem_info' set but not used
[-Wunused-but-set-variable]
lan91c96.c: In function 'smc_send_packet':
lan91c96.c:320:16: warning: variable 'ioaddr' set but not used
[-Wunused-but-set-variable]
Fix clash between IH_ARCH_NDS32 and IH_ARCH_SANDBOX
NDS32 and SANDBOX architecture were sharing the same IH_ARCH number
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Acked-by: Macpaul Lin <macpaul@andestech.com> Acked-by: Marek Vasut <marek.vasut@gmail.com>
Igor Grinberg [Mon, 7 Nov 2011 01:14:06 +0000 (01:14 +0000)]
env: clean env_embedded.c checkpatch and code style
Cleanup the env_embedded.c checkpatch warnings, errors and coding style.
There is one error left though:
ERROR: Macros with multiple statements should be enclosed in a do - while loop
#79: FILE: u-boot/common/env_embedded.c:79:
+#define GEN_ABS(name, value) \
+ asm(".globl " GEN_SYMNAME(name)); \
+ GEN_SET_VALUE(name, value)
total: 1 errors, 0 warnings, 213 lines checked
We cannot enclose that statement in a do - while loop,
because these are a global assembly declarations.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Igor Grinberg [Mon, 7 Nov 2011 01:14:05 +0000 (01:14 +0000)]
env: clean env_mmc.c checkpatch and code style
Cleanup the env_mmc.c checkpatch warnings, errors and coding style.
Simplify env_relocate_spec() function implementation.
Also mark internal functions as static.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Igor Grinberg [Mon, 7 Nov 2011 01:14:04 +0000 (01:14 +0000)]
env: clean env_nvram.c checkpatch and code style
Cleanup the env_nvram.c checkpatch warnings, errors and coding style.
There are 2 wanring left about the extern used in c file:
WARNING: externs should be avoided in .c files
#53: FILE: env_nvram.c:53:
+extern void *nvram_read(void *dest, const long src, size_t count);
WARNING: externs should be avoided in .c files
#54: FILE: env_nvram.c:54:
+extern void nvram_write(long dest, const void *src, size_t count);
total: 0 errors, 2 warnings, 138 lines checked
There is no common nvram header file to use instead of the externs.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Igor Grinberg [Mon, 7 Nov 2011 01:13:59 +0000 (01:13 +0000)]
env: clean cmd_nvedit.c checkpatch and code style
Cleanup the cmd_nvedit.c checkpatch warnings, errors and coding style.
There are 10 wanrings left about the simple_strtoul() function:
WARNING: simple_strtoul is obsolete, use kstrtoul instead
#359: FILE: cmd_nvedit.c:359:
+ load_addr = simple_strtoul(argv[2], NULL, 16);
...
total: 0 errors, 10 warnings, 1043 lines checked
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Simon Glass [Fri, 4 Nov 2011 06:42:35 +0000 (06:42 +0000)]
Define uintptr_t as long int to simplify printf() format strings
If uintptr_t can be either an unsigned int or an unsigned long int, it is
tricky to use it in a printf() format string. This changes it to
unsigned long int consistently. This should do the right thing on both
32-bit and 64-bit architectures.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
David Wagner [Mon, 26 Sep 2011 03:26:34 +0000 (03:26 +0000)]
new tool mkenvimage: generates an env image from an arbitrary config file
This tool takes a key=value configuration file (same as would a `printenv' show)
and generates the corresponding environment image, ready to be flashed.
use case: flash the environment with an external tool
Signed-off-by: David Wagner <david.wagner@free-electrons.com>
Acked-by; Mike Frysinger <vapier@gentoo.org> Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Wolfgang Grandegger <wg@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Wolfgang Grandegger <wg@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Simon Glass <sjg@chromium.org>
Wolfgang Denk [Mon, 21 Nov 2011 21:04:17 +0000 (22:04 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
* 'master' of git://git.denx.de/u-boot-blackfin:
Blackfin: cache result of cpp check
Blackfin: traps: fix up printf warnings from debug
Blackfin: drop now unused local variable
Wolfgang Denk [Mon, 21 Nov 2011 21:02:35 +0000 (22:02 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-nds32
* 'master' of git://git.denx.de/u-boot-nds32:
nds32/lib: add ide generic support
nds32: enhance io.h for compatibility with periphals
ftide020: fix incorrect information display format
Wolfgang Denk [Mon, 21 Nov 2011 21:00:37 +0000 (22:00 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-nios
* 'master' of git://git.denx.de/u-boot-nios:
nios2: Offer ft_board_setup() capability and call fdt_fixup_ethernet().
board/nios2-generic: Use altera_pio driver and remove board specific driver
gpio: Add driver for Altera's PIO core
nios2: Pseudo implement dcache_status/enable/disable()
Aneesh V [Sat, 5 Nov 2011 07:43:33 +0000 (13:13 +0530)]
Makefile: Add the missing dependency for spl target
Wolfgang's patch for build time improvement is bringing
out issues due to missing dependencies in the top-level
Makefile. I get errors such as the below while building
with many threads.
make[1]: /home/a0393566local/u-boot-denx/tools/mkimage: Command not found
This also allows one to do:
$ make spl/u-boot-spl.bin
if you want to build only spl
Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Aneesh V <aneesh@ti.com>
Zang Roy-R61911 [Sun, 6 Nov 2011 22:22:36 +0000 (22:22 +0000)]
e1000: fix unused variable waring for e1000 driver
Fix the following build warning in drivers/net/e1000.c
e1000.c: In function 'e1000_reset_hw':
e1000.c:1373:11: warning: variable 'icr' set but not used [-Wunused-but-set-variable]
e1000.c: In function 'e1000_phy_init_script':
e1000.c:4395:11: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com>
The original commit broke long standing assumption that md commands work
on effective addresses. This normally isn't an issue for most systems
that map 1:1, however on systems with a 36-bit address map it breaks.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kim Phillips [Tue, 15 Nov 2011 23:02:23 +0000 (23:02 +0000)]
common: tsi148 - fix gcc 4.6 compiler warning
Configuring for vme8349 board...
cmd_tsi148.c: In function 'tsi148_init':
cmd_tsi148.c:56:17: warning: variable 'lastError' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Configuring for kmeter1 board...
km83xx_i2c.c: In function 'i2c_make_abort':
km83xx_i2c.c:44:8: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Heiko Schocher <hs@denx.de>
Kim Phillips [Tue, 15 Nov 2011 22:59:51 +0000 (22:59 +0000)]
mpc83xx: spd_sdram - fix gcc 4.6 compiler warning
Configuring for sbc8349 board...
spd_sdram.c: In function 'spd_sdram':
spd_sdram.c:152:41: warning: variable 'trfc_high' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fix:
s3c24x0_rtc.c: In function 'rtc_get':
s3c24x0_rtc.c:67:53: warning: variable 'a_armed' set but not used
s3c24x0_rtc.c:67:45: warning: variable 'a_year' set but not used
s3c24x0_rtc.c:67:38: warning: variable 'a_mon' set but not used
s3c24x0_rtc.c:67:30: warning: variable 'a_date' set but not used
s3c24x0_rtc.c:67:22: warning: variable 'a_hour' set but not used
s3c24x0_rtc.c:67:15: warning: variable 'a_min' set but not used
s3c24x0_rtc.c:67:8: warning: variable 'a_sec' set but not used
[-Wunused-but-set-variable]
Fix:
yaffs_guts.c: In function 'yaffs_CheckChunkErased':
yaffs_guts.c:854:6: warning: variable 'result' set but not used
yaffs_guts.c: In function 'yaffs_UpdateObjectHeader':
yaffs_guts.c:3463:6: warning: variable 'result' set but not used
yaffs_guts.c: In function 'yaffs_GrabChunkCache':
yaffs_guts.c:3774:6: warning: variable 'pushout' set but not used
yaffs_guts.c: In function 'yaffs_Scan':
yaffs_guts.c:5237:6: warning: variable 'result' set but not used
yaffs_guts.c: In function 'yaffs_CheckObjectDetailsLoaded':
yaffs_guts.c:5748:6: warning: variable 'alloc_failed' set but not used
yaffs_guts.c:5747:6: warning: variable 'result' set but not used
yaffs_guts.c: In function 'yaffs_ScanBackwards':
yaffs_guts.c:5808:6: warning: variable 'deleted' set but not used
yaffs_guts.c:5806:6: warning: variable 'result' set but not used
yaffs_guts.c: In function 'yaffs_GetObjectName':
yaffs_guts.c:6657:7: warning: variable 'result' set but not used
[-Wunused-but-set-variable]
Fix:
flash.c: In function 'flash_erase':
flash.c:209:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:373:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Fix:
flash.c: In function 'flash_erase':
flash.c:209:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:373:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Fix:
enc28j60.c: In function 'enc_receive':
enc28j60.c:435:5: warning: variable 'eir_reg' set but not used
[-Wunused-but-set-variable]
enc28j60.c: In function 'enc_poll':
enc28j60.c:503:5: warning: variable 'estat_reg' set but not used
[-Wunused-but-set-variable]
Stefan Roese [Tue, 15 Nov 2011 08:03:45 +0000 (08:03 +0000)]
pip405.c: Fix GCC 4.6 build warnings
Fix:
pip405.c: In function 'board_early_init_f':
pip405.c:192:16: warning: variable 'tctp_clocks' set but not used [-Wunused-but-set-variable]
pip405.c:182:16: warning: variable 'dataout' set but not used [-Wunused-but-set-variable]
Stefan Roese [Tue, 15 Nov 2011 08:03:39 +0000 (08:03 +0000)]
mip405.c: Fix GCC 4.6 build warnings
Fix:
mip405.c: In function 'init_sdram':
mip405.c:250:4: warning: variable 'tctp_clocks' set but not used [-Wunused-but-set-variable]
mip405.c: In function 'initdram':
mip405.c:629:9: warning: variable 'ds' set but not used [-Wunused-but-set-variable]
Stefan Roese [Tue, 15 Nov 2011 08:03:33 +0000 (08:03 +0000)]
auto_update.c: Fix GCC 4.6 build warnings
Fix:
../common/auto_update.c: In function 'au_check_header_valid':
../common/auto_update.c:94:16: warning: variable 'checksum' set but not used [-Wunused-but-set-variable]
../common/auto_update.c: In function 'do_auto_update':
../common/auto_update.c:400:30: warning: variable 'got_ctrlc' set but not used [-Wunused-but-set-variable]
Stefan Roese [Tue, 15 Nov 2011 08:03:20 +0000 (08:03 +0000)]
cmd_dasa_sim.c: Fix GCC 4.6 build warnings
Fix:
cmd_dasa_sim.c: In function 'updatePci9054':
cmd_dasa_sim.c:135:6: warning: variable 'val' set but not used [-Wunused-but-set-variable]
cmd_dasa_sim.c: In function 'clearPci9054':
cmd_dasa_sim.c:189:6: warning: variable 'val' set but not used [-Wunused-but-set-variable]
Stefan Roese [Tue, 15 Nov 2011 08:03:00 +0000 (08:03 +0000)]
dlvision-10g.c: Fix GCC 4.6 build warnings
Fix:
dlvision-10g.c: In function 'print_fpga_info':
dlvision-10g.c:90:11: warning: variable 'feature_compression' set but not used [-Wunused-but-set-variable]
Stefan Roese [Tue, 15 Nov 2011 08:02:54 +0000 (08:02 +0000)]
nand_boot.c: Fix GCC 4.6 build warnings
Fix:
nand_boot.c: In function 'nand_read_page':
nand_boot.c:190:6: warning: variable 'stat' set but not used [-Wunused-but-set-variable]
nand_boot.c: In function 'nand_boot':
nand_boot.c:271:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Stefan Roese [Tue, 15 Nov 2011 08:02:49 +0000 (08:02 +0000)]
sata_dwc.c: Fix GCC 4.6 build warnings
Fix:
sata_dwc.c: In function 'sata_dwc_softreset':
sata_dwc.c:444:5: warning: variable 'status' set but not used [-Wunused-but-set-variable]
sata_dwc.c:443:6: warning: variable 'serror' set but not used [-Wunused-but-set-variable]
sata_dwc.c: In function 'scan_sata':
sata_dwc.c:654:16: warning: variable 'lba_desc' set but not used [-Wunused-but-set-variable]
sata_dwc.c:538:16: warning: variable 'xfer_mask' set but not used [-Wunused-but-set-variable]
sata_dwc.c: In function 'ata_dev_read_id':
sata_dwc.c:747:14: warning: variable 'reason' set but not used [-Wunused-but-set-variable]
sata_dwc.c: In function 'ata_dev_read_sectors':
sata_dwc.c:1810:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
sata_dwc.c: In function 'ata_dev_write_sectors':
sata_dwc.c:1994:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
Stefan Roese [Tue, 15 Nov 2011 08:02:37 +0000 (08:02 +0000)]
40x_spd_sdram.c: Fix GCC 4.6 build warnings
Fix:
40x_spd_sdram.c: In function 'spd_sdram':
40x_spd_sdram.c:137:6: warning: variable 'sdram0_b3cr' set but not used [-Wunused-but-set-variable]
40x_spd_sdram.c:136:6: warning: variable 'sdram0_b2cr' set but not used [-Wunused-but-set-variable]
40x_spd_sdram.c:129:6: warning: variable 'sdram0_ecccfg' set but not used [-Wunused-but-set-variable]
Stefan Roese [Tue, 15 Nov 2011 08:02:30 +0000 (08:02 +0000)]
44x_spd_ddr2.c: Fix GCC 4.6 build warnings
44x_spd_ddr2.c: In function 'initdram':
44x_spd_ddr2.c:450:17: warning: variable 'dimm_spd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c: In function 'program_copt1':
44x_spd_ddr2.c:1003:16: warning: variable 'ddrtype' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c: In function 'DQS_calibration_process':
44x_spd_ddr2.c:2498:7: warning: variable 'window_found' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2497:16: warning: variable 'end_rffd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2496:16: warning: variable 'end_rqfd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2495:16: warning: variable 'begin_rffd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2494:16: warning: variable 'begin_rqfd' set but not used [-Wunused-but-set-variable]
44x_spd_ddr2.c:2493:7: warning: variable 'min_end' set but not used [-Wunused-but-set-variable]
Stefan Roese [Tue, 15 Nov 2011 08:02:24 +0000 (08:02 +0000)]
44x_spd_ddr.c: Fix GCC 4.6 build warnings
Fix:
44x_spd_ddr.c: In function 'program_cfg0':
44x_spd_ddr.c:384:16: warning: variable 'dimm_64bit' set but not used [-Wunused-but-set-variable]
44x_spd_ddr.c:383:16: warning: variable 'dimm_32bit' set but not used [-Wunused-but-set-variable]
projects / karo-tx-uboot.git / log