The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
B4860QDS has a PowerOne ZM7300 programmable digital Power
Manager which is programmed as per the value read from
the fuses.
Reference for this code is taken from t4qds VID implementation.
Adds Support for PowerOne ZM7300 voltage regulator.
This device is available on some Freescale Boards like B4860QDS
and has to be programmed to adjust the voltage on the board.
Use zynq_dma_xfer_init, zynq_align_dma_buffer,
zynq_dma_transfer helper function performing dma
transfers so that the code can be reused easily for
different cases of dma transfer.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 25 Apr 2014 11:51:58 +0000 (13:51 +0200)]
fpga: zynq: Remove sparse warnings
Warnings:
drivers/fpga/zynqpl.c:150:32: warning: Using plain integer as NULL pointer
drivers/fpga/zynqpl.c:152:16: warning: Using plain integer as NULL pointer
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 13 Mar 2014 12:07:57 +0000 (13:07 +0100)]
fpga: xilinx: Simplify load/dump/info function handling
Connect FPGA version with appropriate operations
to remove huge switch-cases for every FPGA family.
Tested on Zynq. Spartan2/Spartan3/Virtex2 just compile test.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Akshay Saraswat [Tue, 13 May 2014 05:00:15 +0000 (10:30 +0530)]
S5P: Exynos: Config: Enable GPIO CMD config
Enabling configs for GPIO CMD, EXYNOS4 family and replacing
exynos_gpio_get with new linear GPIO pin number required
because of the new function asking only 2 arguments (pin
and value) instead of 3 (bank, pin and value).
Akshay Saraswat [Tue, 13 May 2014 05:00:14 +0000 (10:30 +0530)]
S5P: Exynos: Add GPIO pin numbering and rename definitions
This patch includes following changes :
* Adds gpio pin numbering support for EXYNOS SOCs.
To have consistent 0..n-1 GPIO numbering the banks are divided
into different parts where ever they have holes in them.
* Rename GPIO definitions from GPIO_... to S5P_GPIO_...
These changes were done to enable cmd_gpio for EXYNOS and
cmd_gpio has GPIO_INPUT same as s5p_gpio driver and hence
getting a error during compilation.
* Adds support for name to gpio conversion in s5p_gpio to enable
gpio command EXYNOS SoCs. Function has been added to asm/gpio.h
to decode the input gpio name to gpio number.
Example: SMDK5420 # gpio set gpa00
Because I'm leaving Samsung Electronics, I won't have access to their
developer hardware anymore. Przemyslaw Marczak will take over my
responsibilities.
Akshay Saraswat [Tue, 6 May 2014 14:37:04 +0000 (20:07 +0530)]
Exynos5: config: Enable FIT
Adding two configs:
* CONFIG_FIT - Enable FIT image support.
* CONFIG_FIT_BEST_MATCH - Enable fetching correct DTB from
FIT image by comparing compatibles.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Ian Campbell [Mon, 28 Apr 2014 19:14:05 +0000 (20:14 +0100)]
net/designware: call phy_connect_dev() to properly setup phylib device
This sets up the linkage from the phydev back to the ethernet device. This
symptom of not doing this which I noticed was:
<NULL> Waiting for PHY auto negotiation to complete....
rather than:
dwmac.1c50000 Waiting for PHY auto negotiation to complete....
Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Wu, Josh [Thu, 8 May 2014 08:14:07 +0000 (16:14 +0800)]
fs/fat: correct FAT16/12 file finding in root dir
When write a file into FAT file system, it will search a match file in
root dir. So the find_directory_entry() will get the first cluster of
root dir content and search the directory item one by one. If the file
is not found, we will call get_fatent_value() to get next cluster of root
dir via lookup the FAT table and continue the search.
The issue is in FAT16/12 system, we cannot get root dir's next clust
from FAT table. The FAT table only be use to find the clust of data
aera in FAT16/12.
In FAT16/12 if the clust is in root dir, the clust number is a negative
number or 0, 1. Since root dir is located in front of the data area.
Data area start clust #2. So the root dir clust number should < 2.
This patch will check above situation before call get_fatenv_value().
If curclust is < 2, include minus number, we just increase one on the
curclust since root dir is in continous cluster.
The patch also add a sanity check for entry in get_fatenv_value().
Łukasz Majewski [Tue, 6 May 2014 07:36:05 +0000 (09:36 +0200)]
fs:ext4:write:fix: Reinitialize global variables after updating a file
This bug shows up when file stored on the ext4 file system is updated.
The ext4fs_delete_file() is responsible for deleting file's (e.g. uImage)
data.
However some global data (especially ext4fs_indir2_block), which is used
during file deletion are left unchanged.
The ext4fs_indir2_block pointer stores reference to old ext4 double
indirect allocated blocks. When it is unchanged, after file deletion,
ext4fs_write_file() uses the same pointer (since it is already initialized
- i.e. not NULL) to return number of blocks to write. This trunks larger
file when previous one was smaller.
Lets consider following scenario:
1. Flash target with ext4 formatted boot.img (which has uImage [*] on itself)
2. Developer wants to upload their custom uImage [**]
- When new uImage [**] is smaller than the [*] - everything works
correctly - we are able to store the whole smaller file with corrupted
ext4fs_indir2_block pointer
- When new uImage [**] is larger than the [*] - theCRC is corrupted,
since truncation on data stored at eMMC was done.
3. When uImage CRC error appears, then reboot and LTHOR/DFU reflashing causes
proper setting of ext4fs_indir2_block() and after that uImage[**]
is successfully stored (correct uImage [*] metadata is stored at an
eMMC on the first flashing).
Due to above the bug was very difficult to reproduce.
This patch sets default values for all ext4fs_indir* pointers/variables.
Steve Rae [Mon, 5 May 2014 20:00:08 +0000 (13:00 -0700)]
disk: part_efi: add support for the Backup GPT
Check the Backup GPT table if the Primary GPT table is invalid.
Renamed "Secondary GPT" to "Backup GPT" as per:
UEFI Specification (Version 2.3.1, Errata A)
York Sun [Sat, 3 May 2014 00:28:04 +0000 (17:28 -0700)]
common/board_f: Initialized global data for generic board
Some platforms (tested on mpc85xx, mpc86xx) use global data before calling
function baord_inti_f(). The data should not be cleared later. Any arch
which uses global data in generic board board_init_f() should define
CONFIG_SYS_GENERIC_GLOBAL_DATA.
Signed-off-by: York Sun <yorksun@freescale.com> CC: Scott Wood <scottwood@freescale.com> CC: Simon Glass <sjg@chromium.org> CC: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Simon Glass <sjg@chromium.org>
Ralph Siemsen [Thu, 1 May 2014 18:18:41 +0000 (14:18 -0400)]
Trivial fix to .gitignore for spl/Makefile
Trivial fix to .gitignore for spl/Makefile
According to the gitignore man page:
"An optional prefix "!" which negates the pattern; any matching file
excluded by a previous pattern will become included again."
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
So the directory exclude "/spl/*" must come before the exception
for spl/Makefile otherwise it has no effect.
Tom Rini [Thu, 1 May 2014 14:01:08 +0000 (10:01 -0400)]
cmd_bootm.c: Only say XIP image when load is image_start
We say we have an XIP (in this case, image loaded at desired execution
address) when the image header has been offset in the load. It's
possible that in some cases executing the header is non-fatal but that's
not true in many other cases.
Kristian Otnes [Fri, 25 Apr 2014 13:35:43 +0000 (15:35 +0200)]
hush shell: Avoid string write overflow when entering max cmd length
console_buffer array is defined to be CONFIG_SYS_CBSIZE + 1 long,
whereas the_command array only CONFIG_SYS_CBSIZE long. Subsequent
use of strcpy(the_command, console_buffer) will write final \0
terminating byte outside the_command array when entering a command
of max length.
Signed-off-by: Kristian Otnes <kotnes <at> cisco <dot> com>
Andreas Bießmann [Sun, 20 Apr 2014 08:34:15 +0000 (10:34 +0200)]
lib/sha256: fix compile on some hosts
Commit 2842c1c24269a05142802d25520e7cb9035e456c introduced lib/sha256 into
mkimage. Since then it will be compiled with HOSTCC which may produce errors
on some systems. Most BSD systems (like OS X for me) do not ship a
linux/string.h which will lead to take the U-Boot provided
include/linux/string.h in the end. This header howver is completely wrong
here. Just take the string.h if compiling with HOSTCC and linux/string.h when
not.
Makefile: Build with -Werror=date-time if the compiler supports it
GCC 4.9 and newer have a new warning -Wdate-time, which warns on any use
of __DATE__, __TIME__, or __TIMESTAMP__, which would make the build
non-deterministic. Now that the kernel does not use any of those
macros, turn on -Werror=date-time if available, to keep it that way.
The kernel already (optionally) records this information at build time
in a single place; other kernel code should not duplicate that.
Signed-off-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Michal Marek <mmarek@suse.cz> Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Shengzhou Liu [Fri, 11 Apr 2014 08:14:17 +0000 (16:14 +0800)]
net/phy: enable get_phy_id redefinable
As some PHYs have non-standard PHY ID registers, PHY Id can't
be read correctly by current get_phy_id function, so we enable
get_phy_id redefinable to permit specific PHY driver having own
specific get_phy_id function.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
AR8035/phy: Enable autonegotiation function for ar8035
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before,
but used "if (phydev->supported & SUPPORTED_Autoneg)" now.
So assign "phydev->supported" to "phydev->drv->features" for ar8035
to enable autonegotiation. Then removed the genphy_config_aneg() function.
keystone serial hw support hw flow control. This patch
enables hw flow control for keystone EVMs as an optional
feature based on CONFIG_SERIAL_HW_FLOW_CONTROL.
fs: fat: Fix cache align error message in fatwrite
Use of malloc of do_fat_write() causes cache error on ARM v7 platforms.
Perhaps, the same problem will occur at any other CPUs.
This replaces malloc with memalign to fix cache buffer alignment.
Simon Glass [Sat, 26 Oct 2013 05:01:32 +0000 (23:01 -0600)]
Make 'run' use run_command_list() instead of run_command()
In the case where an environment variable spans multiple lines, we should
use run_command_list() so that all lines are executed. This shold be
backwards compatible with existing behaviour for existing scripts.
This adds support for the 7" WVGA produced by Future Eletronics and
make it dynamically detect if it is connected or not based on the
touchscreen controller.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de>
On mx6sl there is a LVE (Low Voltage Enable) bit in the IOMUXC_SW_PAD_CTL
register that can enable or disable low voltage on the pad.
LVE is bit 22 of IOMUXC_SW_PAD_CTL register, but in order to make the
calculation easier we can define it as a flag in bit 1, since this bit is unused.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Tim Harvey [Mon, 5 May 2014 15:22:25 +0000 (08:22 -0700)]
ventana: Add support for the LTC3676 PMIC
The LTC3676 PMIC is used instead of the PFUZE100 PMIC on the
GW51xx/GW52xx/GW53xx Ventana baseboards. In order to support the IMX6Q SoC
at 1GHz on those baseboards, we need to adjust the voltage scaling for the SW1
and SW3 DC/DC converters on the LTC3676 for 1225mV. Note that the scalar
values for the LTC3676 are board-specific as they relate to a resistor devider
chosen by the board design.
Tim Harvey [Wed, 23 Apr 2014 04:53:58 +0000 (21:53 -0700)]
power: Add support for LTC3676 PMIC
The LTC3676 PMIC includes four DC/DC converters, and three 300mA
LDO Regulators (two Adjustable). The DC/DC converters are adjustable based
on a resistor devider (board-specific).
This adds support for the LTC3676 by creating a namespace unique init function
that uses the PMIC API to allocate a pmic and defines the registers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Stefano Babic <sbabic@denx.de>
Michal Simek [Fri, 25 Apr 2014 11:45:08 +0000 (13:45 +0200)]
serial: zynq: Remove sparse warnings
Warnings:
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_init' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_setbrg' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_getc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_tstc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_putc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_puts' was not declared. Should it be static?
drivers/serial/serial_zynq.c:182:22: warning: symbol 'uart_zynq_serial0_device' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_init' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_setbrg' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_getc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_tstc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_putc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_puts' was not declared. Should it be static?
drivers/serial/serial_zynq.c:185:22: warning: symbol 'uart_zynq_serial1_device' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This change removes LCD menu download mode info screen.
Now key press timeout is checked in function download_menu()
and menu options are displayed directly after PWR + VOLUP keys.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
samsung: misc: menu: increase delay in menu main loop
Increase menu loop delay to 200 ms helps choose the right
menu option by user. Before this, each time key was pressed
the current menu option was changed few times.
Now it changes only once and also changes few times if key
is pressed for a longer time.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This menu option allows restore gpt.
This is usefull and no needs access to the u-boot console.
For proper operation:
- each partition uuid should be set in environment or
- CONFIG_RANDOM_UUID should be defined for automatically uuid setting
After operation success device is going to be reset.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
samsung: misc: allows using environmental macros as args in menu commands
Function cmd_process() runs commands with directly given list of arguments
but it doesn't expand given environmental variables names as macros.
Command "gpt" as one of arguments expects expanded macro e.g. $partitions
so it needs to be called by function run_command().
Changes:
- extend array mode_name by lower case commands names - used by find_cmd()
- put each command arguments into one string - used by run_command()
- use run_command() instead of cmd_process()
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Michal Simek [Fri, 25 Apr 2014 11:45:08 +0000 (13:45 +0200)]
serial: zynq: Remove sparse warnings
Warnings:
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_init' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_setbrg' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_getc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_tstc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_putc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_puts' was not declared. Should it be static?
drivers/serial/serial_zynq.c:182:22: warning: symbol 'uart_zynq_serial0_device' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_init' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_setbrg' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_getc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_tstc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_putc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_puts' was not declared. Should it be static?
drivers/serial/serial_zynq.c:185:22: warning: symbol 'uart_zynq_serial1_device' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 25 Apr 2014 12:17:38 +0000 (14:17 +0200)]
net: zynq: Fix sparse warnings in gem
Add missing header.
Warnings:
drivers/net/zynq_gem.c:491:5: warning: symbol 'zynq_gem_initialize' was not declared. Should it be static?
drivers/net/zynq_gem.c:542:5: warning: symbol 'zynq_gem_of_init' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Wu, Josh [Mon, 10 Mar 2014 08:40:41 +0000 (16:40 +0800)]
at91: video: atmel_hlcdfb.c: fix bad timing configuration
The right correspondance between LCD margins and LCD timings is:
* upper margin -> vertical back porch
* lower margin -> vertical front porch
* left margin -> horizontal back porch
* right margin -> horizontal front porch
Stephen Warren [Fri, 18 Apr 2014 17:15:55 +0000 (11:15 -0600)]
config: enable CMD_BMP when API+LCD is enabled
When both CONFIG_API and CONFIG_LCD are enabled, the API code calls
lcd_display_bitmap(). That isn't compiled unless either CONFIG_CMD_BMP
or CONFIG_SPLASH_SCREEN is enabled. In order to prevent build problems,
have config_fallbacks.h enable CONFIG_CMD_BMP when both API and LCD are
enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / karo-tx-uboot.git / log