Shaohui Xie [Mon, 19 Aug 2013 10:58:52 +0000 (18:58 +0800)]
powerpc/t4240: add QSGMII interface support
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Shaohui Xie [Mon, 19 Aug 2013 10:43:07 +0000 (18:43 +0800)]
powerpc/common/vsc3316: remove const from vsc3316_config parameter define
Since the parameters need to be modified according to different Serdes
protocols at runtime, the const will block this. Also remove const from
arrays define used by vsc3316_config.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Shruti Kanetkar [Thu, 15 Aug 2013 16:25:38 +0000 (11:25 -0500)]
powerpcv2: Print hardcoded size like print_size() does
Makes the startup output more consistent
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: York Sun <yorksun@freescale.com>
85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions.
because of this code checkpatch script generates "WARNING: Avoid CamelCase".
Convert variables name to normal naming convention and modify board, driver
files with updated the new structure.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:15 +0000 (15:16 +0800)]
TPL : introduce the TPL based on the SPL
Due to the nand SPL on some board(e.g. P1022DS)has a size limit, it can
not be more than 4K. So, the SPL cannot initialize the DDR with the SPD
code. This patch introduces TPL to enable a loader stub that is loaded
by the code from the SPL. It initializes the DDR with the SPD or other
operations.
The TPL's size is sizeable, the maximum size is decided by the memory's
size that TPL runs. It initializes the DDR through SPD code, and copys
final uboot image to DDR. So there are three stage uboot images:
* spl_boot, * tpl_boot, * final uboot image
Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:13 +0000 (15:16 +0800)]
powerpc : spi flash : Support to start from eSPI with SPL
This patch introduces SPL to enable a loader stub that being loaded by
the code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:11 +0000 (15:16 +0800)]
powerpc: mpc85xx: Support booting from SD Card with SPL
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Ying Zhang [Fri, 16 Aug 2013 07:16:10 +0000 (15:16 +0800)]
powerpc: deleted unused symbol CONFIG_SPL_NAND_MINIMAL and enabled some functionality for common SPL
1. The symbol CONFIG_SPL_NAND_MINIMAL is unused, so deleted it.
2. Some functions were unused in the minimal SPL, but it is useful
in the common SPL. So, enabled some functionality for common SPL.
Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Łukasz Majewski [Fri, 16 Aug 2013 13:33:33 +0000 (15:33 +0200)]
i2c:samsung: Adjust Trats, GONI and Universal_c210 boards to work with new I2C framework
New I2C framework, introduced after v2013.07 final release, imposed I2C
code adjustment for some Samsung boards - namely Trats, GONI and Universal_c210.
Those boards were using schematic based I2C enumeration (I2C_5, I2C_9).
However, new I2C framework imposes usage of logical I2C adapters numbering
(e.g. I2C_0, I2C_1, etc).
Additionally, I2C_GET_* macros were replaced with i2c_*_bus_num() functions.
Trats board gained definition of second soft I2C adapter.
Chunhe Lan [Fri, 16 Aug 2013 07:10:37 +0000 (15:10 +0800)]
fsl_i2c: add workaround for the erratum I2C A004447
This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.
At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.
The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Heiko Schocher <hs@denx.de>
Disabling the data cache is no longer required to boot Dalmore, so
enable it. This results in notably better performance when loading
and booting the Linux kernel.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Currently all Tegra SoCs are assumed to have 32 byte cache lines. This
isn't true for Tegra114, however, which uses 4 Cortex-A15 cores and
therefore uses a cache line size of 64 bytes. Move the cache line size
setting to the per-SoC common configuration file.
Signed-off-by: Thierry Reding <treding@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Joel Fernandes [Mon, 19 Aug 2013 08:14:14 +0000 (16:14 +0800)]
SPL: Makefile: Build a separate autoconf.mk for SPL
SPL defines CONFIG_SPL_BUILD but this does not percolate to the
autoconf.mk Makefile. As a result the build breaks when
CONFIG_SPL_BUILD is used in the board-specific include header file. With
this, there is a possibility of having a CONFIG option defined in the
header file but not defined in the Makefile causing all kinds of build
failure and problems.
It also messes things for up, for example, when one might want to
undefine options to keep the SPL small and doesn't want to be stuck with
the CONFIG options used for U-boot. Lastly, this also avoids defining
special CONFIG_SPL_ variables for cases where some options are required
in U-boot but not in SPL.
We add a spl-autoconf.mk rule that is generated for SPL with the
CONFIG_SPL_BUILD flag and conditionally include it for SPL builds.
Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Ying Zhang <b40530@freescale.com>
Wolfgang Denk [Sun, 28 Jul 2013 20:12:46 +0000 (22:12 +0200)]
board/esd/cpci750/mv_eth.c: Fix license
The file header indicated that this file was GPL-2.0+, but actually
the code was derived from (Marvell based) Linux source code which is
only GPL-2.0. Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Acked-by: Stefan Roese <sr@denx.de>
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README Acked-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Sun, 28 Jul 2013 20:12:44 +0000 (22:12 +0200)]
SPDX-License-Identifier: fixing some problematic GPL-2.0 files
Unlike the other patches in this series so far, this commit fixes a
ambiguity in the license terms for some OMAP files: the code was
originally derived from the Linux kernel sources, where it was clearly
marked as GPL-2.0 (i. e. without the "or later" part), but the U-Boot
version had a GPL-2.0+ file header added, apparently without
permission / relicensing from the original authors of the code.
Insert a GPL-2.0 SPDX-License-Identifier to fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Tom Rix <Tom.Rix@windriver.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Tom Rini <trini@ti.com>
net: phy/realtek: Add support for RTL8211DN and RTL8211E phy modules
This patch adds support for Realtek PHY modules RTL8211DN and
RTL8211E (variants: RTL8211E-VB-CG, RTL8211E-VL-CG, RTL8211EG-VB-CG),
which can be found on Freescale's T1040RDB boards.
To make the driver more generic across 8211 family, a generic name 8211x
is added for macros and function names.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
Axel Lin [Wed, 3 Jul 2013 03:24:18 +0000 (11:24 +0800)]
net: Use ARRAY_SIZE at appropriate places
Use ARRAY_SIZE instead of having similar implementation in each drivers.
The NUMELEMS defined in drivers/net/npe/include/IxOsalTypes.h is not used
at all, so this patch removes it instead of converting it to use ARRAY_SIZE.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Marek Vasut <marex@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: TsiChungLiew <Tsi-Chung.Liew@freescale.com> Cc: Wolfgang Denk <wd@denx.de> Cc: York Sun <yorksun@freescale.com>
Dirk Eibach [Fri, 9 Aug 2013 08:52:53 +0000 (10:52 +0200)]
powerpc/ppc4xx: Do full iocon PHY initialization in software
Up to this point some PHY initialization was done from the FPGA
and some from u-boot.
From now all initialization is done from u-boot.
To keep this maintainable a PHY setup machine was implemented that can
execute commands from initialization arrays.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
York Sun [Tue, 30 Jul 2013 22:26:11 +0000 (15:26 -0700)]
tools/Makefile: Move _GNU_SOURCE to Makefile
Commit 669dfc2e adds libfdt_env.h to HOSTCPPFLAGS. It causes stdio.h
to be included before _GNU_SOURCE is defined in C files. On some old hosts
some prototypes are protected by #ifdef __USE_GNU, which is set when
_GNU_SOURCE is defined.
Signed-off-by: York Sun <yorksun@freescale.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 Jul 2013 03:10:01 +0000 (20:10 -0700)]
image: Display FIT timestamp when booting
The timestamp is shown in fit_print_contents() but for some reason not
in fit_image_print(). This seems to be an oversight, since it is the latter
which is used by bootm.
Add timestamp printing in this case.
(There is code duplication in these two function, for looking at in a future
patch).
Paul B. Henson [Sun, 4 Aug 2013 04:29:09 +0000 (21:29 -0700)]
bootm: fix conditional controlling call to fixup_silent_linux
This function is only defined if CONFIG_SILENT_CONSOLE is set and
CONFIG_SILENT_U_BOOT_ONLY is not set, the call to it should be based
on the same conditions.
Signed-off-by: Paul B. Henson <henson@acm.org> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 Jul 2013 03:10:00 +0000 (20:10 -0700)]
RFC: bootm: Add silent_linux environment variable
At present the console for linux is silent if the U-Boot console is silent,
unless CONFIG_SILENT_U_BOOT_ONLY is set. I wonder if a better way would be
to have an environment variable to control this? Then we can control the
verbosity from scripts, and set the variable to 'no' for those boards that
want Linux to boot with console output.
TENART Antoine [Tue, 2 Jul 2013 10:06:00 +0000 (12:06 +0200)]
Add TI816X evm board support
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Change to SPDX, fix a few compiler warnings, adapt to
CONFIG_OMAP_COMMON] Signed-off-by: Tom Rini <trini@ti.com>
TENART Antoine [Tue, 2 Jul 2013 10:05:59 +0000 (12:05 +0200)]
Add TI816X support
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Fix warnings about vtp things in emif4.c, adapt AM43XX] Signed-off-by: Tom Rini <trini@ti.com>
TENART Antoine [Tue, 2 Jul 2013 10:05:58 +0000 (12:05 +0200)]
Prepare for TI816X : reuse existing code from TI814X
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX] Signed-off-by: Tom Rini <trini@ti.com>
Heiko Schocher [Mon, 5 Aug 2013 14:00:37 +0000 (16:00 +0200)]
arm, da850: enable the correct uart in arch_cpu_init()
in arch_cpu_init() uart2 is fix enabled, without reference the
setting from CONFIG_SYS_NS16550_COM1. Use the setting from
CONFIG_SYS_NS16550_COM1 for enabling the console.
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Tom Rini <tom.rini@gmail.com> Cc: Christian Riesch <christian.riesch@omicron.at>
Heiko Schocher [Mon, 5 Aug 2013 14:00:36 +0000 (16:00 +0200)]
bootstage: get more BOOTSTAGE_ID* in show_boot_progress()
In case CONFIG_BOOTSTAGE is not defined, call from bootstage_mark_name()
show_boot_progress(), so get more BOOTSTAGE_ID* ids in show_boot_progress()
if CONFIG_BOOTSTAGE is not defined.
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 9 Aug 2013 15:22:18 +0000 (11:22 -0400)]
TI:omap5/dra7xx: Convert to ti_armv7_common.h
Update omap5_common.h to use ti_armv7_common.h, and in turn update
dra7xx_evm.h and omap5_uevm.h slightly. The biggest changes here are
that IP blocks which exist on the platform, and had clocks enabled,
now have the drivers being built as well.
Tom Rini [Fri, 9 Aug 2013 15:22:17 +0000 (11:22 -0400)]
TI:am33xx: Create common config files for TI ARMv7 platforms, and AM33xx
We create two new files, include/configs/ti_armv7_common.h for all of
the common IP blocks and related features / commands we share in
virtually all of our platforms. We then create
include/configs/ti_am335x_common.h for everything common to the am335x
SoC leaving just the board specific parts to
include/configs/ti_am335x_common.h.
Tom Rini [Fri, 9 Aug 2013 15:22:15 +0000 (11:22 -0400)]
arm: spl: For Falcon Mode, set a default machid of ~0
With device trees, boards do not always set CONFIG_MACH_TYPE now, so we
must not rely on this define being set. The kernel uses ~0 to see if we
have a valid machine number or not, so set that as the default, invalid
machine, id and only fix if CONFIG_MACH_TYPE is set.
Acked-by: Dan Murphy <dmurphy@ti.com> Tested-by: Heiko Schocher <hs@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 9 Aug 2013 15:22:13 +0000 (11:22 -0400)]
am33xx: Stop using PHYS_DRAM_1 define
We defined PHYS_DRAM_1 to 0x80000000 (start of DRAM) and then used this
for CONFIG_SYS_SDRAM_BASE. But then we kept on referencing PHYS_DRAM_1
in other places. Change to directly setting CONFIG_SYS_DRAM_BASE and
then using that name in code.
OMAP3: igep00x0: allow booting with a FDT from MMC
IGEP boards now have Device Tree support in the mainline
kernel. To boot an IGEP board using a DT, a uEnv.txt plain
text file could be used to define a custom uenvcmd that will
be run by the default boot command.
It is more convenient to change the default boot command to
allow loading a FDT if it is stored in the boot dir of the
rootfs uSD/MMC partition.
If no FDT is found then the defaul command tries to boot a
zImage without a DT using legacy boot.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
ARM: igep00x0.h: Enable the use of CMD_EXT4, CMD_FS_GENERIC and zImage.
Able to load the kernel from some form of ext[234] or FAT. Also, with v3.9 and
later of the Linux Kernel, uImage isn't builtable anymore by default, so we
should switch to use the bootz command.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Commit "OMAP5: emif/ddr: Change emif settings as required for ES1.0 silicon"
(f40107345cbcd6e0d1747eda45e76c4e2a6df0db)
changed sequence to set final DDR PHY config register value at the beginning.
Looks like it was made by mistake and should be reverted.
Naumann Andreas [Tue, 9 Jul 2013 07:43:17 +0000 (09:43 +0200)]
ARM: omap3: Implement dpll5 (HSUSB clk) workaround for OMAP36xx/AM/DM37xx according to errata sprz318e.
In chapter 'Advisory 2.1 USB Host Clock Drift Causes USB Spec Non-compliance in Certain Configurations' of the TI Errata it is recommended to use certain div/mult values for the DPLL5 clock setup.
So far u-boot used the old 34xx values, so I added the errata recommended values specificly for 36xx init only.
Also, the FSEL registers exist no longer, so removed them from init.
Tested this on a AM3703 board with 19.2MHz oscillator, which previously couldnt lock the dpll5 (kernel complained). As a consequence the EHCI USB port wasnt usable in U-Boot and kernel. With this patch, kernel panics disappear and USB working fine in u-boot and kernel.
Signed-off-by: Andreas Naumann <anaumann@ultratronik.de>
[trini: Add extern to <asm/arch-omap3/clock.h> Signed-off-by: Tom Rini <trini@ti.com>
ARM: IGEP0033: Add support for Flattened Device Tree.
Now, the default kernel to boot the IGEP COM AQUILA is device tree based. As
old kernel is deprecated we should adapt the boot commands to use DTB files.
Also, with v3.9 and later of the Linux Kernel, uImage isn't builtable anymore
by default, so we should switch to use the bootz command.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.
projects / karo-tx-uboot.git / log